AII32650 Security System Hood Switch.pmd

INSTALLATION
INSTRUCTIONS
Accessory
Application
SECURITY SYSTEM
HOOD SWITCH
P/N 08E49-SDA-100
2007 ACCORD
2 AND 4-DOOR
PARTS LIST
Publications No.
AII 32650
Issue Date
JULY 2006
Illustration of the Hood Switch Installed on the
Vehicle
HOOD SWITCH
HARNESS
Hood switch harness
Hood switch
HOOD
SWITCH
2205011T
INSTALLATION
14 Wire ties
Ground bolt
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures should
not be attempted by “do-it-yourselfers.”
Washer-screw
1.
Make sure you have the anti-theft code for the
radio, then write down the radio station presets.
Big washer
2.
Disconnect the negative cable from the battery.
Small washer
Installing the Hood Switch
3.
Nut
Open the hood. Remove the radiator cover (ten
clips and four retaining tabs).
TOOL AND SUPPLIES REQUIRED
#2 Phillips screwdriver
CLIPS (10)
Small flat-tip screwdriver
Felt-tip pen
6 mm and 10 mm Combination wrenches
6 mm and 10 mm Sockets
Ratchet
Torx wrench
Long nose pliers
Diagonal cutters
RADIATOR
COVER
RETAINING TAB
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AII 32650 (0607)
2201032T
08E49-SDA-1000-91
1 of 6
4.
Remove the hood latch cover (one clip).
7.
HOOD LATCH COVER
CLIP
HOOD
OPENER
CABLE
2212030T
Using a felt-tip pen, mark the location of the
existing hood lock bracket at each corner.
BOLT
(Reuse.)
SPRING
HOOD LATCH
BRACKET
2212012T
5.
Remove the spring, and disconnect the hood
opener cable from the hood latch bracket.
8.
Install the hood switch to the hood latch bracket
with the washer-screw, small washer, and nut
supplied.
FELT-TIP PEN
WASHER-SCREW
MARK
HOOD SWITCH
HOOD LATCH
BRACKET
BOLT
(Discard.)
BOLT
(Reuse.)
HOOD LATCH
BRACKET
FELT-TIP PEN
2212020T
2212041T
6.
2 of 6
SMALL
WASHER
Remove the hood latch bracket (three bolts).
Discard the one lower bolt as shown.
AII 32650 (0607)
NUT
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
Routing the Hood Switch Harness
9.
Remove the air duct cover (two clips), and remove
the air duct.
11. Route the hood switch harness 2-pin connector
and ground terminal through the front bulkhead
support to the left of the radiator and outside of
the engine compartment, along the vehicle
harness as shown.
AIR DUCT
COVER
CLIP (2)
HOOD SWITCH
HARNESS
HOOD SWITCH
HARNESS 2-PIN
CONNECTOR
FRONT
FRONT
VEHICLE
HARNESS
AIR DUCT
2213010T
10. Remove the relay box (two bolts), and remove the
one bolt that fastens the air cleaner housing cover.
RELAY BOX
2213031T
12. Lift the air cleaner housing cover up, and route the
hood switch harness to the rear of the air cleaner
housing cover, along the vehicle harness.
BOLT
BOLT
Lift
HOOD SWITCH
HARNESS
AIR CLEANER
HOUSING COVER
VEHICLE
HARNESS
BOLT
(Remove.)
AIR CLEANER
HOUSING COVER
2213023T
2405011T
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AII 32650 (0607)
3 of 6
13. Under the relay box, locate the vehicle 3-pin
connector blue-taped to the vehicle harness, and
remove the blue-tape to free the connector.
Connect the hood switch harness 3-pin connector
to the 3-pin connector you just freed. Secure the
hood switch harness to the vehicle harness with
the wire ties.
NOTE: If the 3-pin connector is already being
used by another accessory, unplug the 3-pin
connector. Locate the 3-pin connector taped to
the harness. Remove the dummy connector from
that harness. Plug the other accessory's harness
3-pin connector into the hood switch harness 3pin connector. Secure the harness with one wire
tie in the area shown.
A/T Model:
BLUETAPE
(Remove.)
VEHICLE
HARNESS
RELAY BOX
VEHICLE
3-PIN
CONNECTOR
HOOD SWITCH
HARNESS 3-PIN
CONNECTOR
WIRE TIE
OTHER
ACCESSORY
HARNESS 3-PIN
CONNECTOR
HOOD
SWITCH
HARNESS
HOOD
SWITCH
HARNESS
HOOD
SWITCH
HARNESS
VEHICLE
HARNESS
OTHER
ACCESSORY
HARNESS
WIRE TIE
VEHICLE HARNESS
VEHICLE 3-PIN
CONNECTOR HOOD SWITCH
HARNESS 3-PIN
2215042T
CONNECTOR
M/T Model:
VEHICLE
HARNESS
RELAY BOX
BLUETAPE
(Remove.)
WIRE
TIE
HOOD SWITCH HARNESS
3-PIN CONNECTOR
2215052T
15. Route the hood switch harness along the vehicle
harness, and secure it to the vehicle harness with
five wire ties in the areas shown.
HOOD SWITCH
HARNESS
HOOD
SWITCH
HARNESS
VEHICLE
HARNESS
FRONT
WIRE TIE
VEHICLE
HARNESS
(Fold back.)
HOOD
SWITCH
HARNESS
WIRE TIE
WIRE TIE
VEHICLE
HARNESS
VEHICLE 3-PIN
CONNECTOR
VEHICLE
HARNESS
HOOD SWITCH
HARNESS 3-PIN
CONNECTOR
2320041T
WIRE TIE
WIRE TIE
VEHICLE
HARNESS
HOOD
SWITCH
HARNESS
4 of 6
AII 32650 (0607)
2215031T
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
16. Reinstall the hood opener cable and the spring on
the hood latch bracket.
HOOD OPENER
CABLE
SPRING
19. Route the hood switch harness 2-pin connector
along the vehicle harness. Plug the hood switch
harness 2-pin connector into the hood switch 2-pin
connector.
HOOD SWITCH
HARNESS
VEHICLE
HARNESS
CENTER
STAY
HOOD
LATCH
BRACKET
HOLE
FRONT
CLIP
2212050T
17. Position the hood lock on the center support at the
position you marked in step 5. Loosely install the
two bolts, and install the hood switch harness
ground terminal with the big washer and ground
bolt from the kit.
2215011T
20. Push the hood switch clip into the hole in the
center stay.
21. Secure the hood switch harness to the vehicle
harness with six wire ties in the areas shown.
MARK
BOLT
(Reuse.)
HOOD SWITCH
HARNESS 2-PIN
HOOD SWITCH
2-PIN CONNECTOR CONNECTOR
HOOD
LATCH
BRACKET
WIRE TIE
VEHICLE
HARNESS
WIRE TIE
BIG
WASHER
GROUND HOOD SWITCH
HARNESS GROUND
BOLT
TERMINAL
BOLT
(Reuse.)
2212062T
18. Close the hood, and check that the alignment of
the hood lock and the hood latch is correct, and
check that the hood is latched securely. When
you’re satisfied with the results, open the hood,
and tighten the hood latch bolts securely.
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
FRONT
HOOD SWITCH
HARNESS
AII 32650 (0607)
2215021T
5 of 6
22. Check that all wire harnesses are routed properly
and all connectors are plugged in.
23. Reinstall all removed parts.
24. Reconnect the negative cable to the battery.
25. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
26. Reset the clock.
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
27. Start the engine. Push down on the driver’s
window switch until the window is fully open.
28. Pull up on the driver’s window switch to close the
window completely, then hold the switch for
2 seconds or more.
29. Test the driver's window AUTO function.
6 of 6
AII 32650 (0607)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
Download PDF
Similar pages