SUPER SUPREME RESOLUTION
IR WEATHER-PROOF CAMERA
SK-P461(D)/M445AI
MANUAL
10. Do not disassemble the unit by yourself. When there is problem with
the unit please contact after-sale service center or the shop where
you bought.
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
5-A. Loosen the bolt A, B, C-1 and C-2 by using the 3mm wrench
included.
6-A. Face the direction of the camera to monitor.
7-A. Tighen the bolt A, B, C-1, C-2 to complete adjustment.
Type - A
WRENCH
BOLT C-1
ACCESSORIES
ANCHOR 6x30, 4EA
SCREW 4x35 TP1 PAN SUS, 4EA
BOLT C-2
WRENCH 3mm L TYPE, 1EA
SUNVISOR BOLT, 1EA
Extra video output cable for installation,
1EA(option)
FEATURE
1. SONY Effio-E2 DSP adopted
2. This camera is incredibly flexible to install with its 3-axis camera
construction, which makes the camera ceiling, wall or slope
mountable.
3. This product is "weather-proof" to resist rain, snow and other weather
factors(IP66)
4. 40M range visible in total darkness with 40pcs of IR LEDs.(Indoor)
5. Adopted 2-DNR technology, It reduces noise efficiently in low light
condition.
6. ATR(Adaptive Tone Reproduction)
7. Day & Night function
8. Super Supreme Resolution(700 TVL - Color)
9. Support 4 different privacy zone
10. Multi function : High Light Mask, Motion Detection, Privacy Mask,
Defect Pixel Correction, Mirror
11. Multi-language full OSD support
CAUTION
1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED light directly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface.
It will cause falling or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
(Use the AC adaptor 12V DC regulated, 1A)
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Due to the possibility of water leakage, do not cut or peel off the
cable. In case you cut or peel off the cable, the warranty will be void.
8. Please use the camera unit within given temperature and electricity limit.
9. Please make sure that installation should be done by qualified service
person only.
BOLT A
BOLT B
5-B. Loosen the bolt by using the 3mm wrench included.
6-B. Face the direction of the camera to monitor.
7-B. Tighten the bolt to complete adjustment.
Type - B
HOW TO INSTALL
BOLT
1. Make a hole of Ø25mm in diameter for passing cable.
2. Drill four holes on the wall or ceiling and insert the anchors.
3. Arrange the cables and fix the screws.
ANCHOR 6x30, 4EA
Ø6
WRENCH
Ø25
DIMENSION
SCREW Tp1 4x35, 4EA
80.4
4. Attach the sunvisor and fix the sunvisor fixing bolt.
Type - A
101.7
BOLT
SUNVISOR
206.7
80.4
Type - B
101.7
205.9
2. OSD menu structure
SPECIFICATION
Model No.
SK-P461/M445AI
SK-P461D/M445AI
Image Sensor
1/3" COLOR SONY SUPER HAD CCDⅡ(960H)
Effective Pixel
976(H) x 494(V) Pixel(NTSC), 976(H) x 582(V) Pixel(PAL)
Scanning System
2:1 Interlace
Sync. Type
Internal
Resolution
Color : 700 TV-Line, B/W : 800 TV-Line
S/N
52dB or More(AGC OFF)
Video Output
Min. Illumination
Gamma
Shutter Speed
AUTO
X0.25/X0.50/X0.75/X1.00
ON(Selectable 0~15)/OFF
Motion Detection
ON/OFF Selectable(4 Zone)
Privacy Zone
ON/OFF Selectable(4 Zone)
Mirror
Day & Night
ICR(AUTO, COLOR, B/W, EXT1)
LED Output
IR LED 40pcs, IR Optimizer
RS-485(Pelco-D, SK-P) / ID 1~99 / 2400, 4800, 9600bps
MANUAL
Regulated 12V DC ±10%
12V DC/24V AC Dual voltage
Max. 600mA(at 12V DC/24V AC) : LED ON
Operation Temp.
-10℃ ~ 50℃
Preservation Temp.
-20℃ ~ 60℃
Dimension
Weight
Iris speed select
Manual iris lens
Mode : Auto iris, Shut + Auto iris,
Shut
Brightness : 0~255(30)
Low Luminance
Auto exposure setting
Shutter : 1/60(1/50), 1/120(1/100),
1/250, 1/500, 1/1000,
1/2000, 1/4000,
Manual exposure setting
1/10000
Speed : 0~255(250)
Delay CNT : 0~255(16)
ATW
80.4(W) x 80.7(H) x 101.7(D)mm
Approx. 900g
ATW Frame : X0.50, X1.00,
X1.50, X2.00
USER1
B-Gain, R-Gain
USER2
B-Gain, R-Gain
ANTI CR
Level(0~255)
MANUAL
FUNCTION SETTING
1. How to use the jog lever
①ENTER :
ㆍPush the lever : Used to access the
6
menu and confirm selection.
7
FZ
ㆍPush the lever for one second : Used
EXT.VIDEO
to return to previous menu from the
motion detection setting section or
2
8
privacy mask setting section.
4
5
② UP, ③ DOWN : Used to move the
3 1
cursor to up or down.
④LEFT, ⑤ RIGHT : Used to move the
*OSD menu & Focus/Zoom
cursor to left or right and change the
adjustment direction
1. Unfasten the screw of the
value.
bottom door
⑥ FOCUS, ⑦ ZOOM : Use a '+' type
2. Adjust the jog lever & Focus
driver for adjusting zoom and focus.
/Zoom trimmers
3. Tighten the screw of the
(In case of operation Focus/Zoom,
bottom door
don't put stress excessively.)
⑧EXT. VIDEO : Extra video output terminal for installation. Plug your
test monitor in here. The cable is option.
Auto trace white balance setting
(1,800 ~ 10,500 )
Automatically adjust the white balance under
all conditions
The gain values for the outdoor fixed mode
(Adjust the Red or Blue values)
The gain values for the fluorescent light fixed
mode(Adjust the Red or Blue values)
Color rolling suppression
4. BACKLIGHT
OFF
BLC
Deactivated function
Back Light Compensation
High Light Compensation
HLC
5. ATR(=DWDR) (Adaptive Tone Reproduction)
OFF
Luminance : Low, Mid, High
ON
Contrast : Low, Midlow, Mid,
Midhigh, High
Set the ATR to OFF
Set the extent of the luminance compression
Set the extent of the contrast enhancement
6. DAY/NIGHT
Burst : OFF, ON
AUTO
Delay CNT : 000~255(005)
Day→Night : 000~255(004)
Night→Day : 000~255(016)
COLOR
B/W
EXT1
EXT2
Day : Color ↔ Night : B/W
(Switching time & speed adjustable)
Fixed at color
Burst : OFF, ON
IR Optimizer : OFF, ON
Mode : Auto, Center
Level : 0~31(022)
Y/C, OFF, Y, C
Set the 2D NR(Noise Reduction) filter mode
Y LEVEL
000~015(004)
Set the Y(luminance signal) filter strength
C LEVEL
000~015(004)
Set the C(chrominance signal) filter strength
8. PICT ADJUST
MIRROR
OFF, ON
Set the horizontal flip
BRIGHTNESS
000~255(000)
Set the screen brightness
CONTRAST
000~255(128)
Set the screen contrast
SHARPNESS
000~255(128)
Set the screen sharpness
HUE
000~255(128)
Adjust the hue
GAIN
000~255(128)
Adjust the color gain
OFF
Set the camera ID to OFF
Letters A to Z, Numerals 0 to 9, You can enter up to 26 letters & 2 lines
Symbols
ON
10. MOTION DET
Set the motion detection to OFF
Detect sense, Block disp,
Monitor area, Area sel
(Top, Bottom, Left, Right)
ON
Manual white balance
Move the camera lens toward to white paper
then press the set button to find the optimal
white balance for current environment
PUSH LOCK
NR MODE
OFF
Environment : Indoor, Outdoor
PUSH
7. NR(=2DNR)
9. CAMERA ID
AGC : 6.00, 12.00, 18.00,
24.00, 30.00, 36.00,
42.00, 44.80
Vari-focal auto iris lens
Current Consumption
Speed : 0~255(48)
3. WHITE BAL
YES
Lens
Auto iris lens(only DC type)
Auto/Open/Close select
Mode : AGC, OFF
Brightness : X0.25, X0.50,
X0.75, X1.00
Mode : Shut + AGC
BLC/HLC/ATR/OFF
DNR(2D)
Type : DC, Video
Mode : Auto, Open, Close
High luminance
1/60(1/50) ~ 1/100,000sec
AGC
Summary
2. SHUTTER/AGC
ATW(1,800 ~ 10,500 )/PUSH/USER1/USER2/
ANTI CR/MANUAL/PUSH LOCK
Backlight
Sub Menu
MANUAL
Yes(Multi Language)
White Balance
Power Supply
AUTO
1.0 Vp-p(Sync. Negative) Termination 75Ω
0.1 Lux(F/1.2) : LED OFF, 0 Lux(40M Range) : LED ON
γ= 0.45 typ.
OSD
Communication(option)
Select Menu
1. LENS
Fixed at B/W
Auto day & night switching mode for IR LED
built-in type(Default)
No use for this model
Adjust the settings of motion detection
11. PRIVACY
Set the privacy masks to OFF
OFF
Area sel(Top, Bottom, Left, Right),
Adjust the settings of privacy
Color, Trasp, Mosaic
ON
12. LANGUAGE
English, Japanese, Chinese, Deutsch, Francais,
Pyccknn, Portugues, Espanol
Select language
13. CAMERA RESET
Restore all the settings to the default values
14. EXIT
SAVE ALL
Save all the setting made
EXIT
Exit the OSD menu
ㆍThe ' ' icon appeared with desired function, press the set button to move sub menu.
ㆍThe '- - -' icon appeared with function that is unavailable according to function setting.
3. Communication menu(option)
(1) How to use the jog lever
① Control jog lever : Left → Right → Left → Right → Down →
Enter(Push)
②Controller : Pelco-D Preset #96 + SAVE
(2) Communication menu structure
Select Menu
Sub menu
Summary
Address
01 ~ 99
Address setting
Protocol
Pelco-D, SK-P
Protocol setting
Baudrate
2400, 4800, 9600
Baudrate setting
Exit
Exit
Exit the communication menu
※All specification is subject to change without notice to improve the quality.
3B25177A
Download PDF
Similar pages