IS0095E
INSTRUCTIONS:
Nextfit Shoulder Pad
Replacement Kit
IMPORTANT: Please also refer to the
instructions that came with your product.
13 Check to make sure BOTH metal Harness Pins are
WARNING: Avoid serious injury or death to your child.
Never use your NextFit car seat without shoulder pads
in place. You must read and understand the Shoulder Pad
Replacement Kit instructions and the instructions in the
User Guide. If you do not understand these instructions,
DO NOT attempt to replace the Shoulder Pads, STOP
and call Chicco at 1-877-424-4226.
Kit Includes:
Flat Head
screwdriver
(not included)
1 set of Shoulder
Pads (Right and
Left)
14 Unbuckle Harness and Repeat Steps 1 thru 5 in
secured! The metal pins must be inserted fully and the
plastic Locks must be snapped upward to hold the metal
Harness Pins in place. Pull on straps to make sure they
have been properly secured.
REVERSE order: 5) Unfold the softgoods on each side,
4) Re-fasten Seat Bottom, 3) Re-fasten Seat Back Panel,
2) Add Newborn Insert (if being used), 1) Lower Headrest if necessary. Refer to User Guide if necessary.
1 Refer to User Guide to raise the
Headrest and unbuckle and loosen
Harness as shown.
2 Remove Newborn Insert (if being used) as shown.
15 IMPORTANT Final Check! Make sure Shoulder Pads, Chest Clip, and Buckle
Tongues are oriented as shown. Check to make sure Harness Straps are flat and not
twisted when buckled! Check to make sure Buckle is inserted correctly through the
cutout in Seat Bottom Panel. Refer to User Guide if necessary.
WARNING: Avoid serious injury or death to your child. You must make sure that all harness components
and shoulder pads have been replaced correctly, so the seat can provide maximum crash protection. Pull
on adjuster strap and the shoulder straps of the harness and operate the harness after this replacement is
complete. Make sure all straps are properly routed and secured. Make sure Shoulder Pads, Chest Clip, and
Buckle Tongues are oriented and installed correctly. If you have a problem, retry these instructions provided
AND review your User Guide. If you still have problems, STOP, Do Not use the Car Seat, and call Chicco at
1-877-424-4226.
4
4a
3 Lift the Seat Back Panel as shown.
4b
4 Unsnap Seat Bottom Panel 4a and pull forward 4b.
6b
!
6a
5 Fold softgoods under BOTH sides to access the
metal Harness Pins.
!
6 ! IMPORTANT - Only press hard enough on plastic lock
to release the metal Harness Pin and move it forward without
permanently deforming the plastic lock.
8 Remove the metal Harness Pin completely and release
the Harness Strap, as shown. Repeat steps 6 thru 8 to remove
the metal Harness Pin on the OTHER side.
2
10 Replace the Right and Left Shoulder Pad on the
9 ! IMPORTANT - Do not mix up LEFT and RIGHT parts.
Harness Straps as shown. Replace Chest Clip and Buckle
Tongues as shown.
NEVER use the Child Restraint without Shoulder Pads.
! IMPORTANT - Check to make sure LEFT and RIGHT parts
are oriented as shown before proceeding to the next step.
Remove Parts from both of the Harness Straps (Harness
Buckle Tongue, Chest Clip and Shoulder Pads).
Your
LEFT
flat head screwdriver as shown.
Your
RIGHT
!
Press down on the plastic Harness Pin Lock with a flat head
screwdriver to release the metal Harness Pin 6a. At the same
time move the metal pin slightly past the plastic lock by lifting
and tugging on the webbing in a forward direction 6b.
7 Slide the metal Harness Pin forward using a
Your
LEFT
Your
RIGHT
11 Buckle BOTH Harness Straps and fold as shown. Check
to make sure Harness Straps are flat and not twisted!
3
12 Place the looped end of the Harness Strap
between the Harness Pin Guide Ribs and reinsert
the metal Harness Pin as shown. Repeat for the
OTHER side.
6b
!
6a
5 Fold softgoods under BOTH sides to access the
metal Harness Pins.
!
6 ! IMPORTANT - Only press hard enough on plastic lock
to release the metal Harness Pin and move it forward without
permanently deforming the plastic lock.
8 Remove the metal Harness Pin completely and release
the Harness Strap, as shown. Repeat steps 6 thru 8 to remove
the metal Harness Pin on the OTHER side.
2
10 Replace the Right and Left Shoulder Pad on the
9 ! IMPORTANT - Do not mix up LEFT and RIGHT parts.
Harness Straps as shown. Replace Chest Clip and Buckle
Tongues as shown.
NEVER use the Child Restraint without Shoulder Pads.
! IMPORTANT - Check to make sure LEFT and RIGHT parts
are oriented as shown before proceeding to the next step.
Remove Parts from both of the Harness Straps (Harness
Buckle Tongue, Chest Clip and Shoulder Pads).
Your
LEFT
flat head screwdriver as shown.
Your
RIGHT
!
Press down on the plastic Harness Pin Lock with a flat head
screwdriver to release the metal Harness Pin 6a. At the same
time move the metal pin slightly past the plastic lock by lifting
and tugging on the webbing in a forward direction 6b.
7 Slide the metal Harness Pin forward using a
Your
LEFT
Your
RIGHT
11 Buckle BOTH Harness Straps and fold as shown. Check
to make sure Harness Straps are flat and not twisted!
3
12 Place the looped end of the Harness Strap
between the Harness Pin Guide Ribs and reinsert
the metal Harness Pin as shown. Repeat for the
OTHER side.
IS0095E
INSTRUCTIONS:
Nextfit Shoulder Pad
Replacement Kit
IMPORTANT: Please also refer to the
instructions that came with your product.
13 Check to make sure BOTH metal Harness Pins are
WARNING: Avoid serious injury or death to your child.
Never use your NextFit car seat without shoulder pads
in place. You must read and understand the Shoulder Pad
Replacement Kit instructions and the instructions in the
User Guide. If you do not understand these instructions,
DO NOT attempt to replace the Shoulder Pads, STOP
and call Chicco at 1-877-424-4226.
Kit Includes:
Flat Head
screwdriver
(not included)
1 set of Shoulder
Pads (Right and
Left)
14 Unbuckle Harness and Repeat Steps 1 thru 5 in
secured! The metal pins must be inserted fully and the
plastic Locks must be snapped upward to hold the metal
Harness Pins in place. Pull on straps to make sure they
have been properly secured.
REVERSE order: 5) Unfold the softgoods on each side,
4) Re-fasten Seat Bottom, 3) Re-fasten Seat Back Panel,
2) Add Newborn Insert (if being used), 1) Lower Headrest if necessary. Refer to User Guide if necessary.
1 Refer to User Guide to raise the
Headrest and unbuckle and loosen
Harness as shown.
2 Remove Newborn Insert (if being used) as shown.
15 IMPORTANT Final Check! Make sure Shoulder Pads, Chest Clip, and Buckle
Tongues are oriented as shown. Check to make sure Harness Straps are flat and not
twisted when buckled! Check to make sure Buckle is inserted correctly through the
cutout in Seat Bottom Panel. Refer to User Guide if necessary.
WARNING: Avoid serious injury or death to your child. You must make sure that all harness components
and shoulder pads have been replaced correctly, so the seat can provide maximum crash protection. Pull
on adjuster strap and the shoulder straps of the harness and operate the harness after this replacement is
complete. Make sure all straps are properly routed and secured. Make sure Shoulder Pads, Chest Clip, and
Buckle Tongues are oriented and installed correctly. If you have a problem, retry these instructions provided
AND review your User Guide. If you still have problems, STOP, Do Not use the Car Seat, and call Chicco at
1-877-424-4226.
4
4a
3 Lift the Seat Back Panel as shown.
4b
4 Unsnap Seat Bottom Panel 4a and pull forward 4b.