PORTABLE GENERATOR
INSTRUCTION MANUAL
SGB16500VSa
SGBT20000VSa
WWW.DAISHIN-JAPAN.CO.JP
P・No.15750165000
Dear Customer:
We carefully manufactured to give you a dependable operation.
However, similar to all mechanical products, your machine will occasionally require
adjustments and maintenance.
This manual should be read carefully before operating
or performing any adjustments on your machine.
Please contact DAISHIN dealer if
technical assistance is required.
Please be advised that unit was designed / manufactured for specific applications.
So
please do not modify and use the unit for any application other than which it was
designed for.
If you have any questions regarding any applications, please ask
DAISHIN dealer before using.
Please read an instruction manual before use.
Safety Messages
Your safety and the safety of others are very important. We have provided important
safety messages in this manual and on the generator. Please read these messages
carefully.
Safety message alerts you to potential hazards that could hurt you or others. Each safety
message is preceded by a safety alert symbol and one of three words; DANGER,
WARNING, or CAUTION.
These words mean:
You will be killed or seriously hurt if you don't follow instructions.
You can be killed or seriously hurt if you don't follow instructions.
You can be hurt if you don't follow instructions.
Each message tells you what the hazard is, what can happen, and what you can do to
avoid or reduce injury.
-1-
Damage Prevention Messages
You will also see other important messages that are preceded by the word.
NOTICE
This word means:
Your generator or other property could be damaged if you don't follow
instructions.
The purpose of these messages is to help prevent damage to your generator, other
property, or the environment.
-2-
Table of Contents
1. SAFETY LABEL LOCATION .............................................. 4
2. SAFETY MESSAGES ......................................................... 6
3. COMPONENTS ................................................................... 8
4. CONTROLS ........................................................................ 11
5. BEFORE STARTING ENGINE ............................................ 13
6. OPERATION ....................................................................... 14
7. STOPPING ENGINE ........................................................... 16
8. MAINTENANCE .................................................................. 17
9. TRANSPORTING AND STORAGE ..................................... 27
10. WATTAGE INFORMATION ................................................. 28
11. TROUBLE SHOOTING ....................................................... 29
12. SPECIFICATION ................................................................. 31
13. WIRING DIAGRAM ............................................................. 32
-3-
1. SAFETY LABEL LOCATION
These labels warn you of potential hazards that can cause serious injury.
Read them carefully.
If a label comes off or becomes hard to read, contact your DAISHIN dealer for a
replacement.
-4-
-5-
2.
SAFETY MESSAGES
Your safety and the safety of others are very important. We have provided important
safety messages in this manual and on the generator. Please read these messages
carefully.
Operator responsibility
・ Know how to stop the generator quickly in case of emergency.
・ Understand the use of all generator controls, output receptacles, and connections.
・ Be sure that anyone who operates the generator receives proper instruction. Do not let
children operate the generator without parental supervision.
Carbon monoxide hazards
・ Exhaust contains poisonous carbon monoxide, a colorless and odorless gas. Breathing
exhaust can cause loss of consciousness and may lead to death.
・ If you the generator in an area that is confined, or even partially enclosed, the air you
breathe could contain a dangerous amount of exhaust gas. To keep exhaust gas from
building up, provide adequate ventilation.
Electric shock hazards
・ The generator produces enough electric power to cause a serious shock or
electrocution if misused.
・ Using a generator or electrical appliance in wet conditions, such as rain or snow, or
near a pool or sprinkler system, or when your hands are wet, could result in
electrocution. Keep the generator dry.
・ If the generator is stored outdoors, unprotected from the weather, check all electrical
components on the control panel, before each use. Moisture or ice can cause a
malfunction or short circuit in electrical components, which could result in electrocution.
・ Do not connect to a building’s electrical system unless an isolation switch has been
installed by a qualified electrician.
Fire and burn hazards
・The exhaust system gets hot enough to ignite some materials.
Keep the generator at least 1 meter (3 feet) away from buildings and other equipment
during operation.
Do not enclose the generator in any structure.
-6-
Keep flammable materials away from the generator.
・ The muffler becomes very hot during operation and remains hot for a while after
stopping the engine. Be careful not to touch the muffler while is in hot. Let the engine
cool before storing the generator indoors.
・ Gasoline is extremely flammable and is explosive under certain conditions. Do not
smoke or allow flames or sparks where the generator is refueled or where gasoline is
stored. Refuel in a well ventilated area with the engine stopped.
・ Fuel vapors are extremely flammable and may ignite after the engine has started. Make
sure that any spilled fuel has been wiped up before starting, the generator.
High altitude
・At altitude over 5000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)
gasoline is acceptable. To remain emissions compliant, high altitude adjustment is
required. Operation without this adjustment will cause decreased performance,
increased fuel consumption, and increased emissions. See a Briggs &Stratton
Authorized Dealer for high altitude adjustment information.
Operation of the engine at altitudes below 2500 feet (762 meters) with the high altitude
kit is not recommended.
-7-
3.
COMPONENTS
FUEL TANK CAP
FUEL METER
LIFTING EYE
FUEL TANK
CHOKE LEVER
CONTROL
PANEL
ENGINE
CASTER
BATTERY
A battery liquid is not in
at the time of the
factory shipment. Fill a
suitable battery liquid
before the use.
FUEL VALVE
GENERATOR
MUFFLER
-8-
CONTROL PANEL
SGB16500VSa (220V 50Hz)
CIRCUIT BREAKER
GROUND TERMINAL
HOUR METER
VOLT METER
AC TERMINALS
PILOT LAMP
ENGINE KEY SWITCH
AC RECEPTACLES
SGBT20000VSa (220/380V 50Hz)
CIRCUIT BREAKER
VOLT METER
HOUR METER
GROUND TERMINAL
PILOT LAMP
ENGINE KEY SWITCH
AC TERMINALS
-9-
AC RECEPTACLES
CASTER KIT
FLANG NUT M8
FLANG BOLT M8-20
CASTER
CASTER
CASTER(STOPPER)
- 10 -
4.
CONTROLS
Engine key switch
To start and stop the engine.
Switch position:
Off: To stop the engine. Key can be removed/ inserted.
On: To run the engine after starting.
Start: To start the engine by turning the starter motor.
OFF
ON
PILOT
ENGINE SW.
OFF
ON
START
START
AC 220V
ENGINE KEY SWITCH
Return the key to the “ON” position once the engine has started. Do not use the starter for
more than 5 seconds at a time. If the engine fails to start, release the switch and wait 10
seconds before operating the starter again.
Fuel valve
The fuel valve is located between the fuel tank
and carburetor.
When the valve lever is in the “ON” position,
fuel is allowed to flow from the fuel tank to the
carburetor. Be sure to return the lever to “OFF”
OFF
after stopping the engine.
ON
- 11 -
Choke Lever
The choke is used to provide proper starting mixture when the engine is cold. It can be
opened and closed by operating the choke lever manually.
Slide has the lever out toward “CLOSED” to enrich the mixture.
SLIDE HAS THE LEVER
CLOSED POSITION
Circuit Breaker
The Circuit breaker will automatically cut off the circuit if there is a short circuit or a
significant overload of the generator at the receptacle.
If the circuit breaker is OFF automatically, check that the appliance is working properly
and does not exceed the rated load capacity of the circuit before turn on to reset the circuit
breaker.
Ground terminal
The generator ground terminal is connected to the frame of the generator, the metal
non-current carrying parts of the generator, and the ground terminals of each receptacle.
Pilot lamp
The pilot lamp is illuminated when the generator is operating normally.
- 12 -
5.
BEFORE STARTING ENGINE
1)
Fill recommended engine oil to the upper limit mark if the oil is short.
2)
Change oil if it becomes dirty or discolored.
Oil capacity at upper limit mark:
See attached OPERATOR’S MANUAL.
LOWER LIMIT
3)
Remove the tank cap and check the fuel
level.
If fuel level is low, refill with unleaded
UPPER LIMIT
automotive gasoline.
4)
Fuel tank capacity: see page 20 (this
INSTRUCTION MANUAL)
5)
Battery liquid is not in at the time of the
factory shipment. Fill a suitable battery
liquid.
1)
Remove the battery cell caps.
2)
Fill the electrolyte into the each cell,
the level must be maintained between the
UPPER and LOWER limit marks.
3)
Peel the protection seal.
Protection seal
Battery cell cap
- 13 -
6.
1.
OPERATION
STARTING THE ENGINE (Refer to OPERATOR’S MANUAL for engine.)
1)
Make sure that disconnect all electrical
loads from panel receptacles.
The generator may be hard to start if a
load is connected.
OFF
2)
Turn the fuel valve to the “ON” position.
3)
ON
If you want to start operate the choke manually, move the choke knob to the
“CLOSED” position.
OPEN POSITION
CLOSED POSITION
OFF
4)
PILOT
Start the engine
ENGINE SW.
ON
OFF
ON
With the electric starter:
START
Turn the engine key switch to the
START
“START” position and hold it there
until the engine starts.
AC 220V
Do not use the electric starter for more than 5 seconds at the time.
If the engine fails to start, release the switch and wait 10 seconds
before operating the starter again.
- 14 -
When the speed of the starter motor drops after a period of the time, it
is the indication that the battery should be recharged.
5)
After the engine starts, let the engine switch return to “ON”.
6)
If you have manually closed the choke, move it to the “OPEN” position as the
engine warms up.
2.
APPLYING AC LOAD
1)
2)
Start engine (see STARTING THE ENGINE).
Allow the engine to warm up for 2-3 minutes before connecting tools or
appliances.
3)
Insert the plug of the electrical appliance into “AC RECEPTACLE”.
4)
Turn the circuit breaker knob to the on position.
** Do not take a current exceeding the specified amperage.
** Be sure that total wattage of all appliances does not exceed the rated output of the
generator.
When the generator is overloaded or a short circuit is made, the CIRCUIT BREAKER will
trip to protect the circuit automatically. If CIRCUIT BREAKER trips during operation, the
generator is either over loaded or the appliance is defective.
Check the appliance and / or generator for overloading or defect make necessary
corrections or repairs before use.
BE SURE THAT THE TOTAL WATTAGE OF ALL APPLIANCES DOES NOT
EXCEED THE RATED OUTPUT OF THE GENERATOR.
- 15 -
7.
STOPPING ENGINE
1)
Turn the circuit breaker knob to the “OFF” position.
2)
Turn the engine key switch to the “OFF” position.
OFF
PILOT
ENGINE SW.
OFF
ON
START
AC 220V
3)
Disconnect all electrical loads from panel receptacles.
4)
Turn the fuel valve to the “OFF” position.
OFF
Never leave an appliance plugged into the generator when you stop the generator as
damage could result to the generator and / or appliance.
- 16 -
8.
MAINTENANCE
Periodic maintenance and adjustment is necessary to keep the generator in good operating
condition. Perform the service and inspection at the intervals shown in the Maintenance
schedule below.
Exhaust gas contains poisonous carbon monoxide. Shut off the engine
before performing any maintenance. If the engine must be run, make sure the area is well
ventilated.
Use only genuine BRIGGS&STRATTON parts or their equivalent for
maintenance or repair. Replacement parts that are not of equivalent quality may damage
the engine.
MAINTENANCE SCHEDULE
REGULAR SERVICE PERIOD
Every
Performed at every indicated hours or operating
annually interval, whichever comes first.
First 5
100
400
use
hours
hours or
hours or
Annually
Annually
ITEM
Check level
Every
Each
○
Engine oil
Change
Engine oil filter
○
Replace
○
Check
Air filter
○
○
Clean
○(1)
Replace
○(1)
Spark plug
Replace
Valve clearance
Check- adjust
Oil cooling fins
Clean
○
○(2)
○(1)
Clean
○
fuel filter
Replace
○
Fuel tank
Check
Every 600 hours or Annually
Fuel tube
Clean
Every 600 hours or Annually
(1) In dusty conditions or when airborne debris is present, clean more often.
(2) Not required unless engine performance problem are noted.
- 17 -
These items should be service by your dealer, unless the owner has the
Engine oil is a major factor affecting engine performance and service life.
No detergent and 2-stroke engine oils will damage the engine and are not
recommended.
Check the oil level BEFORE EACH USE with the generator on a level surface with the
engine stopped.
Use a high quality detergent oil classified for API Service SJ,SL or equivalent.
Use no special additives with recommended oils. Do not mix oil with gasoline.
Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to
select the best viscosity for the outdoor temperature range expected.
**
below 40°(4℃)the use of SAE 30 will result in hard starting.
** Abobe 80°F(27℃) the use of 10W-30 may cause increased oil consumption.
Check oil level more frequently.
- 18 -
Engine oil change
Drain the oil while the engine is warm to assure rapid and complete draining.
1) Remove the drain plug and sealing washer, oil filler cap, and drain the oil.
2) Reinstall the drain plug and sealing washer. Tighten the plug securely.
3) Refill with the recommended oil and check the level.
In case of removing the drain pipe, please control the extended pipe by spanner.
Oil filler cap
Oil capacity:
2.3ℓ (2.42 US qt , 2.03 lmp qt)
Drain plug
Use some tray
Engine oil filter change
1) Drain the oil from the engine.
2) remove the oil filter and dispose of properly.
Used an oil filter socket, rather than a strap wrench, to avoid striking and damaging
the oil pressure switch.
3) Before installing the new oil filter, lightly lubricate the oil filter gasket with fresh,
clean oil.
4) Install the oil filter by hand until the gasket contacts the oil filter adapter, then
- 19 -
tighten the oil filter 1/2 to 3/4 turns.
Replacement parts must be the same and installed in the same position as the
original parts.
5) Add oil. Start and run the engines. As the engine warm up, check for oil leaks.
6) Stop the engine and check the oil level. It should be at the FULL mark on the
dipstick.
Used motor oil may cause skin cancer if repeatedly left in contact with the skin for
prolonged periods. Although this is unlikely unless you handle used oil on a daily
basis, it is still advisable to thoroughly wash your hands with soap and water as
soon as possible after handling used oil.
Please dispose of used motor oil in a manner that is compatible with the environment. We
suggest you take it in a sealed container to your local service station or recycling center for
reclamation. Do not throw it in the trash or pour it on the ground.
Refueling
Fuel tank capacity: 37ℓ (9.78 USG)
Check the fuel level gauge, and refill the tank if the fuel level is low.
Gasoline is highly flammable and explosive, and you can be burned or seriously
injured when handling fuel.
・Stop engine and keep heat, sparks, and flame away.
・Handle fuel only outdoors.
・Wipe up spills immediately.
Refuel in a well-ventilated area before starting the engine. If the engine has been running,
allow it to cool. Refuel carefully to avoid spilling. Do not fill above the shoulder of the fuel
strainer. After refueling, tighten the fuel tank cap securely.
- 20 -
Never refuel the generator inside a building where gasoline fumes may reach flames or
sparks. Keep gasoline away from appliance pilot lights, barbecues, electric appliances,
power tools, etc.
Spilled fuel is not only a fire hazard, it causes environmental damage. Wipe up spills
immediately.
LEVEL GAUGE
Do not fill above fuel
strainer level gauge
FUEL TANK CAP
Spark plug service
Recommended spark plugs: XC92YC(CHAMPION)
To ensure proper engine operation, the spark plug must be properly gapped and free of
deposits.
If the engine has been running, the muffler will by very hot. Be careful not to touch the
muffler.
1)
2)
3)
Remove the spark plug cap.
Clean any dirt from around the spark plug
0.76mm
base.
(0.03 in)
Use the wrench supplied in the tool kit to
remove the spark plug.
4)
Visually inspect the spark plug. Discard it
if the insulator is cracked or chipped.
Clean the spark plug with a wire brush if it
is to be reused.
5)
Measure the plug gap with a feeler gauge.
- 21 -
Correct as necessary by carefully bending
the side electrode.
The gap should be: 0.76mm (0.03 in)
6)
Check that the spark plug washer is in good condition, and thread the spark plug
in by hand to prevent cross-threading.
7)
After the spark plug is seated, tighten with a spark plug wrench to compress the
washer.
Spark plug tightening torque:20N-m(2.0kg・m , 180lb-in)
The spark plug must be securely tightened. An improperly tightened spark plug
can become very hot and could damage the engine.
Never use spark plugs which have an improper heat range. Use only the
recommended spark plugs or equivalent.
Air cleaner service
A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor malfunction,
service the air cleaner regularly. Service more frequently when operating the generator in
extremely dusty areas.
Operating the engine without an air filter, or with a damaged air filter, will allow dirt to
enter the engine, causing rapid engine wear,
This type of damage is not covered by the Distributor’s limited warranty.
Inspection
Remove the air cleaner cover and inspect the filter
Elements. Clean or replace dirty filter elements.
Always replace damaged filter elements.
1) remove the knob(①) and the cover(②).
2) Remove the nut(③) and the retainer(④).
3) Remove the air filter(⑤)
4) Remove the pre-cleaner(⑥),if equipped, from
- 22 -
the air filter.
5) To loosen debris, gentry tap the air filter on a
hard surface. If the air filter is excessively dirty,
replace with a new air filter.
6) Wash the pre-cleaner in liquid detergent and water. Then allow it to
thoroughly air dry.
Do not oil the pre-cleaner.
7)
8)
9)
Assemble the dry pre-cleaner to the air filter.
Install the air filter and secure with retainer and nut.
Install the cover and secure with knob.
Fuel sediment cup cleaning
FUEL VALVE
The sediment cup prevents dirt or water which
may be in the fuel tank from entering the
carburetor. If the engine has not been run for a
long time, the sediment cup should be cleaned.
1) Turn the fuel valve to the “OFF” position.
Remove the sediment cup, O-ring, and
filter.
2) Clean the sediment cup, O-ring, and filter
in nonflammable or high flash point
SEDIMENT CUP
solvent.
3) Reinstall the filter, O-ring, and sediment
FUEL FILTER
cup.
4) Turn the fuel valve “ON” and check for
leaks.
O-RING
SEDIMENT CUP
Fuel filter
1) before replacing the fuel filter (①) ,if equipped, drain the fuel tank or close the fuel
shut-off valve. Otherwise, fuel can leak out and cause a fire or explosion.
2) Use pliers to squeezed tabs (②) on the clamps (③), then slide the clamps away
from the fuel filter. Twist and pull the fuel lines ④ off the fuel filter.
3) Check the fuel lines for cracks or leaks. Replace if necessary.
- 23 -
4) Replace the fuel filter with an original equipment replacement filter.
5) Secure the fuel lines with the clamps as shown.
Fuse replacement
If the fuse isblown, the engine will not start until it is replaced.
1) Turn the engine switch OFF
2) Remove the fuse holder and replace the fuse. Use only a 10A fuse.
If frequent fuse failure occurs, determine the cause and correct the
problem before attempting to operate the generator further.
Never use a fuse with a rating other than 10A. Serious damage to the
electrical system or a fire may result.
10A fuse inside the
control panel
Battery
The generator’s engine has a 3-amp charging system to charge the battery while the
engine is running. If the generator is only used periodically, the battery must be
charged monthly to maintain the battery service life.
A lead acid battery self discharges at a rate of 0.5-1.0% per day. This means that the
battery, if the generator is not operated in a month, can discharge as much as 30% in
the same period. This could cause the engine not to crank or shorten the service life of
the battery. To charge the battery, follow the procedures below.
Removal
1) Remove the battery set plate.
2) Remove the negative(-) cable from the battery negative(-) terminal, then remove
the battery positive(+) terminal.
- 24 -
Negative (-)
cable
Positive (+)
cable
3)Remove the battery
from the battery tray.
Battery set plate
Inspection
1) Remove the battery cell caps.
2) Inspect the electrolyte level of
each cell. The electrolyte level
must be maintained between the
UPPER and LOWER limit marks.
3) If the electrolyte level is near the
LOWER mark, add distilled water
as necessary.
・The battery contains sulfuric acid(electrolyte) which is highly corrosive and
poisonous.
・Getting electrolyte in your eyes or on your skin can cause serious bums.
・Wear protective clothing and eye protection when working near the battery.
EMERGENCY PROCEDURES
・Eyes-Flush with water from a cup or other container for at least 15 minutes
(water under pressure can damage the eye). Immediately call a physician,
local poison control.
・Skin-Remove contaminated clothing. Flush the skin with large quantities of
water. Call a physician immediately.
・Swallowing-Drink water or milk. Call your local poison control center or a
physician immediately.
- 25 -
Charging
The battery is rated at 28AH(ampere-hour). 10% of the ampere-hour rating should be
used as the charging current. A battery charger should be used that can be adjusted
to deliver 1.4 amps.
・The battery gives off expiosive hydrogen gas during normal operation.
・A spark or open flame can cause the battery to explode with enough force to
kill or seriously hurt you.
・Keep sparks and flames away. Wear protective clothing and a face shield, or
have a skilled mechanic do battery maintenance.
1) Remove the battery cell caps.
2) Connect the battery charger following the manufacturer’s instructions.
3) Charge the battery 3-4 hours.
4) After the battery is charged, inspect the electrolyte level in each of the cells.
Add distilled water as necessaery.
5) Install the battery caps.
6) Clean the outside of the battery and the battery tray with a solution of baking soda
and water.
Installation
1) Install the battery in the generator.
2) Install the positive(+) cable to the battery positive(+) terminal, then install the
Negative(-) cable to the battery negative(-) terminal.
3) Install the battery set plate.
Positive (+)
cable
Negative (-)
cable
Battery set plate
- 26 -
9.
TRANSPORTING AND STORAGE
When transporting the generator, turn the engine switch and the fuel valve “OFF”. Keep
the generator level to prevent fuel spillage. Fuel vapor or spilled fuel may ignite.
Contact with a hot engine or exhaust system can cause serious burns or fires.
Let the engine cool before transporting or storing the generator.
Take care not to drop or strike the generator when transporting. Do not place heavy
objects on the generator.
Before storing the unit for an extended period:
1)
Be sure the storage area is free of excessive humidity and dust.
2)
Service according to the table below:
STORAGE TIME
RECOMMENDED SERVICE PROCEDURE TO PREVENT
HARD STARTING
Less than 1 month
No preparation required.
1 to 2 months
Fill with fresh gasoline and add gasoline conditioner*.
2 months to 1 year
Fill with fresh gasoline and add gasoline conditioner*.
Drain the carburetor float bowl.
Drain the fuel sediment cup.
1 year or more
Fill with fresh gasoline and add gasoline conditioner*.
Drain the carburetor float bowl.
Drain the fuel sediment cup.
Remove the spark plug. Put a tablespoon of engine oil into
the cylinder. Turn the engine slowly with the pull rope to
distribute the oil. Reinstall the spark plug. Change the engine
oil.
After removal from storage, drain the stored gasoline into a
suitable container, and fill with fresh gasoline before starting.
* Use gasoline conditioners that are formulated to extend storage life.
Contact your authorized DAISHIN dealer for conditioner recommendations.
- 27 -
Gasoline is extremely flammable and is explosive under certain conditions.
Perform this task in a well ventilated area with the engine stopped. Do not
smoke or allow flames or sparks in the area during this procedure.
When storing gasoline or equipment with fuel in tank
Store away from furnaces, stoves, water heaters or other appliances that have pilot
lights or other ignition sources because they can ignite gasoline vapors.
Fuel system
Fuel can become stale when stored over 30days. Stale fuel causes acid and gum
deposits to from in the fuel system or on essential carburetor parts. To keep fuel fresh,
use FRESH START fuel stabilizer, available as a liquid additive or a drip concentrate
cartridge.
There is no need to drain gasoline from the engine if a fuel stabilizer is added
according to instructions. Run the engine for 2 minutes to circulate the stabilizer
throughout the fuel system. The engine and fuel can then be stored up to 24 months.
If gasoline the engine has not been treated with a fuel stabilizer, it must be drained into
an approved container. Run the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain freshness.
10. WATTAGE INFORMATION
Some appliance needs a “surge” of energy at starting. This means that the amount of
electrical power needed to start the appliance may exceed the amount needed to maintain
its use.
Electrical appliance and tools normally come with a label indicating voltage, cycles/ HZ,
amperage and electrical power needed to run the appliance or tool. If no specification
label is found, check with your nearest dealer for the power surge of your appliances or
power tools.
- 28 -
11. TROUBLE SHOOTING
When the engine will not start:
- 29 -
No electricity at the A.C RECEPTACLES:
- 30 -
12. SPECIFICATION
Models
SGB16500VSa
Frequency (Hz)
Type
50Hz
Revolving field self excited AC generator
Voltage Regulation
AVR
System
Generator
Phase
Single
Three
AC Output Rat.
12.8kVA
16.0kVA
AC Output Max.
14.5kVA
18.0kVA
220V
220/380V
100
80
AC Voltage
Rated Power factor
Model
BRIGGS & STRATTON
Displacement
Engine
Others
SGBT20000VSa
993cm
VANGUARD 33HP
3
Maximum Output
24.6kW / 3600rpm
Oil Alert System
Low lubricating oil pressure
Starting System
Electric Starter
L×W×H
※1
Dry Weight
※2
950.5(950.5)×679(679)×672(886)
207(215)Kg
Fuel Tank Capacity
※1 (
)With Caster kit.
※2 (
)With Battery.
37 liters
NOTE: Specifications are subject to change without notice.
- 31 -
13. WIRING DIAGRAM
SGB16500VSa (220V, 50Hz)
- 32 -
SGBT20000VSa (3P, 380V/220V, 50Hz)
- 33 -
MEMO
DAISHIN INDUSTRIES LTD.
1520-1,FUNATSUKE,YORO-CHO,
YORO-GUN,GIFU 503-1382 JAPAN
PHONE : 81-(0)584-36-0501
FAX : 81-(0)584-36-0504
URL : http://www.daishin-japan.co.jp
MAIL : overseas@daishin-japan.co.jp
Download PDF
Similar pages