TE 2-A
Bedienungsanleitung
de
Operating instructions
en
Mode d’emploi
fr
Istruzioni d’uso
it
Gebruiksaanwijzing
nl
Manual de instruções
pt
Manual de instrucciones
es
Brugsanvisning
da
Käyttöohje
fi
Bruksanvisning
no
Bruksanvisning
sv
Οδηγιες χρησεως
el
Kasutusjuhend
et
Lietošanas pamācība
lv
Instrukcija
lt
Ръководство за обслужване
bg
Upute za uporabu
hr
Instrukcja obsługi
pl
Инструкция по зксплуатации
ru
Návod na obsluhu
sk
Navodila za uporabo
sl
Návod k obsluze
cs
Használati utasítás
hu
zh
ja
ko
cn
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
1
9
1
2
3 4
5
8
6
7
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
2
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
3
4
2
3
1
L
R
4
R
L
R
L
R
L
R
L
5
2
1
L
R
6
2
1
7
8
2
1
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
1
3
9
6
5
4
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
6
7
8
ORIGINAL OPERATING INSTRUCTIONS
TE 2-A cordless rotary hammer
It is essential that the operating instructions
are read before the tool is operated for the
first time.
Always keep these operating instructions
together with the tool.
Ensure that the operating instructions are with
the tool when it is given to other persons.
1. General information
en
1.1 Signal words and their meaning
-CAUTIONUsed to draw attention to a potentially dangerous situation which could lead to minor personal injury or damage
to the equipment or other property.
-NOTEUsed to draw attention to an instruction or other useful
information. Not used for dangerous situations or where
damage to the equipment or property could occur.
1.2 Pictograms
Warning signs
Operating controls and parts Chuck
Function selector switch
Forward / reverse switch
Motor brake
Control switch (with electronic speed control)
Battery release buttons (2)
Rating plate
Grip
Side handle with depth gauge (option)
General
warning
Warning:
electricity
Warning:
hot surface
Warning:
caustic
substances
Wear
breathing
protection
Wear
protective
gloves
Obligation signs
Wear
eye
protection
Wear
ear
protection
Symbols
Read the
operating
instructions
before use
Contents
1. General information
2. Description
3. Tools and accessories
4. Technical data
5. Safety rules
6. Before use
7. Operation
8. Care and maintenance
9. Troubleshooting
10. Disposal
11. Manufacturer’s warranty – tools
12. Declaration of conformity (original)
Page
11
12
13
13
14
16
17
18
19
19
20
20
V
–––
--no
/min
Return
waste material for
recycling
= volts
= direct current
= no load speed
= revolutions per minute
= hammer drilling
= rotation only
These numbers refer to the corresponding illustrations. The illustrations can be found on the fold-out cover pages. Keep these pages open while studying the
operating instructions.
In these operating instructions, the TE 2-A cordless rotary
hammer with battery fitted is referred to as “the tool”.
11
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
en
Location of identification data on the tool
The type designation, item number, year of manufacture
and technical status can be found on the rating plate on
the tool. The serial number is located on the left side of
the motor housing. Make a note of this data in your operating instructions and always refer to it when making an
enquiry to your Hilti representative or service department.
Type:
Serial no.:
2. Description
The TE 2-A is a cordless rotary hammer for professional use. Its ergonomically designed rubber-padded grip
reduces fatigue and provides a secure hold.
The items supplied include:
- The electric tool
- B24/2.0 NiCd, B24/2.4 NiCd or B24/3.0 NiMH battery
- C 7/24 or C 7/36-ACS charger
- Operating instructions
- Toolbox or cardboard box
2.1 Use of the tool as directed
The TE 2-A is a hand-held cordless rotary hammer for
driving and removing screws, drilling in steel, wood and
masonry and hammer drilling in concrete and masonry. It is intended for use on construction sites of all kinds
for general construction, interior finishing, conversion
and renovation work.
● The tool is designed for continuous use.
● The tool may be used only in a dry environment.
● Do not use the tool where there is a risk of fire or explosion.
● Use only the insert tools and accessories intended for
use with this tool.
● The tool may be powered only by the batteries approved
for use with this tool.
● The batteries are to be used exclusively to power tools
of the Hilti 24 V line.
● Use only the recommended battery charger.
●
described in these operating instructions is not permissible.
● To avoid the risk of injury, use only original Hilti accessories and additional equipment.
● Observe the information printed in the operating instructions concerning operation, care and maintenance.
● The tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel
or when used not as directed.
2.2 Requirements to be met by users
The tool is intended for professional use.
The tool may be operated, serviced and repaired only
by authorized, trained personnel. This personnel must
be informed of any special hazards that may be encountered.
● Always concentrate on the job you are doing. Proceed
carefully and do not use the tool if your full attention
is not on the job.
●
●
2.3 Important features of the tool
– Vibration-absorbing grip (rubber-padded)
– Smooth speed control
– Gearing and clutch with permanent lubrication
(grease)
– Automatic cut-out carbon brushes
– Forward / reverse rotation
– Function selector switch for rotary drilling/hammer
drilling
Modification or manipulation of the tool other than
3. Tools and accessories
Side handle and depth gauge
Grease
Cleaning cloth
Charger
Charger
Charger
Battery
Battery
Battery
Toolbox/cardboard box
Belt adaptor
12
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
Optional
Optional
Optional
C 7/24
C 7/36-ACS
TCU 7/36
B24/2.0 NiCd (depending on country)
B24/2.4 NiCd (depending on country)
B24/3.0 NiMH
BAP 24
4. Technical data
Tool
TE 2-A
Rated voltage
24 V –––
--Weight as per EPTA-Procedure 01/2003
3.9 kg
Dimensions (LxHxW)
325 x 260 x 92 mm
Speed under no load
980 r.p.m.
Speed
900 r.p.m.
Hammering speed
0 … 74 Hz (0 … 4410 blows per min.)
Single impact energy
1.5 joules
Chuck
TE-C
Hammer drilling dia. range in concrete and masonry
4 to 16 mm
Drilling using keyless chuck adaptor for cylindrical drill bits
- Drilling dia. range in wood
3 to 13 mm
- Drilling dia. range in metal
3 to 10 mm
Screwdriving using bit adaptor
- Wood screws
Up to 6 mm
- HUD screws
Up to 6 mm
Speed control
Electronic control switch
Forward / reverse
Electrical switch with interlock to prevent activation
when running
Gearing section sealed to prevent entry of dust and with permanent lubrication (maintenance-free)
en
-NOTEThe vibration emission level given in this information sheet has been measured in accordance with a standardised
test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if
the tool is used for different applications, with different accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure level over the total working period. An estimation of the
level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working
period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain
the tool and the accessories, keep the hands warm, organisation of work patterns.
Noise and vibration information (measured in accordance with EN 60745):
Typical A-weighted noise power level:
97 dB (A)
Typical A-weighted noise pressure level:
86 dB (A)
For the given sound power level as per EN 60745, the tolerance is 3 dB.
Wear ear protection!
Triaxial vibration value (vibration vector sum)
measured in accordance with EN 60745-2-1
Drilling in metal, (ah, D)
measured in accordance with EN 60745-2-6
Hammer drilling in concrete, (ah, HD)
Uncertainty (K) for triaxial vibration value
Battery
Rated voltage
Battery capacity
Weight
Temperature monitoring
Type of cell
No. of cells
B24/2.0 NiCd
24 V –––
--24 V × 2.0 Ah
= 48 Wh
1.38 kg
yes
Nickel-cadmium
SUB C type
20
B24/2.4 NiCd
24 V –––
--24 V × 2.4 Ah
= 58 Wh
1.45 kg
yes
Nickel-cadmium
SUB C type
20
2.5 m/s2
14.5 m/s2
1.5 m/s2
B24/3.0 NiMH
24 V –––
--24 V × 3.0 Ah
= 72 Wh
1.43 kg
yes
Nickel-metal hydride
SUB C type
20
Right of technical changes reserved!
13
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
5. Safety rules
en
5.1 General safety rules
-WARNING- Read all instructions! Failure to follow
all instructions listed below may result in electric shock,
fire and/or serious injury. The term "power tool" in all
of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
5.1.1 Work area
a) Keep the work area clean and well lit. Cluttered
and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
5.1.2 Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord approved for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
5.1.3 Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in
14
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
the off position before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of these
devices can reduce dust related hazards.
5.1.4 Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
5.1.5 Battery tool use and care
a) Ensure the switch is in the off position before insert-
ing battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
b) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.
c) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
d) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that
can make a connection from one terminal to another. Shorting the battery terminals together may
cause burns or a fire.
e) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
5.1.6 Service
a) Have your power tool serviced by a qualified repair
person using only genuine replacement parts. This
will ensure that the safety of the power tool is maintained.
5.2 Additional safety precautions
5.2.1 Personal safety
a) Wear ear protection. Excessive noise may lead to
a loss of hearing.
b) Use the auxiliary handle supplied with the tool.
Loss of control of the tool may lead to injury.
c)Always hold the tool securely with both hands on
the grips provided. Keep the grips clean, dry and
free from oil and grease.
d)Adjust the side handle to the desired position and
check that it is fitted and secured correctly.
e)Avoid contact with rotating parts. Switch the tool on
only once it has been brought into the working position close to the workpiece.
f) Avoid unintentional starting. Do not carry the tool
with your finger on the on/off switch. The battery
should be removed from the tool when the tool is
not in use, before work breaks, before maintenance,
before changing insert tools and before transport.
g)Operate the tool only as directed and only when it
is in faultless condition.
h)Exercise your fingers during pauses between work
to improve the blood circulation in your fingers.
i) Check the area behind the wall you are working on
before drilling right through and when using long
drill bits.
j) Breathing protection must be worn when the tool
is used without a dust removal system for work that
creates dust.
k)Activate the safety lock (forward / reverse switch
in the middle position) before storing or transporting the power tool.
l) The tool is not intended for use by children, by
debilitated persons or those who have received no
instruction or training.
m Children must be instructed not to play with the
tool.
n)Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory diseases
to the operator or bystanders. Certain kinds of dust
are classified as carcinogenic such as oak and beech
dust especially in conjunction with additives for
wood conditioning (chromate, wood preservative).
Material containing asbestos must only be treated
by specialists. Where the use of a dust extraction
device is possible it shall be used. To achieve a
high level of dust collection, use a suitable vacuum cleaner of the type recommended by Hilti for
wood dust and/or mineral dust together with this
tool. Ensure that the workplace is well ventilated.
The use of a dust mask of filter class P2 is recommended. Follow national requirements for the materials you want to work with.
5.2.2 Power tool use and care
a) Secure the workpiece. Use clamps or a vice to hold
the workpiece in place. The workpiece is thus held
more securely than by hand and both hands remain
free to operate the tool.
b) Ensure that the insert tools used are equipped with
the appropriate connection end system and that
they are properly fitted and secured in the chuck.
c) Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with
a “live” wire will make exposed metal parts of the tool
“live” and shock the operator.
5.2.3 Electrical safety
a) Before beginning work, check the working area
(e.g. with a metal detector) to ensure that no concealed electric cables or gas and water pipes are
present. External metal parts of the tool may become
live if, for example, an electric cable is damaged
inadvertenly. This presents a serious risk of electric shock.
5.2.4 Work area
a) Ensure that the workplace is well lit.
b) Ensure that the workplace is well ventilated.
Poorly ventilated workplaces may be injurious to
the health due to exposeure to dust.
5.2.5 Personal protective equipment
The user and any other persons in the vicinity must
wear suitable eye protection, ear protection and pro15
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
en
tective gloves when the tool is in use. Breathing protection must be worn if no dust removal system is used.
en
Wear
eye
protection
Wear
ear
protection
Wear
protective
gloves
Wear
breathing
protection
b)Check that the battery is securely attached to the
tool. A falling battery could injure you or other persons.
c)Batteries that have reached the end of their life
must be disposed of safely.
d)Do not charge or continue to use damaged batteries (e.g. batteries with cracks, broken parts, bent
or pushed-in and/or pulled-out contacts).
5.2.6 Battery tool use and care
a)Ensure that the outer surface of the battery is clean
and dry before inserting the battery in the appropriate charger for charging.
6. Before use
1. It is essential that the safety precautions printed in
these operating instructions are read and observed.
2. It is essential that a new battery is charged correctly
when charged for the first time before initial use. Incorrect initial charging can lead to a permanent reduction of battery capacity.
– With the C 7/24 or TCU 7/36 charger: Charge for 24
hours in normal charging mode or for 12 hours in
conditioning mode.
– With the C 7/36-ACS charger: The charger detects
automatically whether initial charging or normal
charging is necessary.
-NOTEThe tool may be used only with B24/2.0 NiCd, B24/2.4
NiCd or B24/3.0 NiMH batteries.
● Battery performance drops at low temperatures.
● Batteries should be stored at room temperature.
● Never store batteries where they are exposed to the
heat of the sun, on a radiator, behind a motor vehicle
windscreen or at a window.
● Never use the battery until the cells become fully discharged. Change to the second battery as soon as a
drop in performance is noticed and recharge the battery immediately so that it is ready for re-use.
●
16
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
6.1 Fitting the side handle (option) -NOTEAn adjustable side handle (option) may be fitted in addition to the two integrated grips. The side handle permits
the tool to be held more securely and thus more comfortably, particularly in the event of inadvertently drilling
into a reinforcing bar.
1. Slacken the side handle clamping band by turning the
side handle in a counterclockwise direction.
2. Slide the side handle clamping band over the chuck
and onto the front section of the tool.
3. Bring the side handle into the desired position.
4. Secure the side handle by turning it in a clockwise
direction.
7. Operation
-CAUTION●
●
●
Noise is emitted by the tool and the
drilling or screwdriving procedure.
Excessive noise may damage the
hearing.
Wear ear protection.
-CAUTION-
●
●
●
The drilling or screwdriving procedure
may cause the material to splinter.
Splintering material may cause injury
to the body, respiratory passages and
the eyes.
Wear eye and breathing protection.
7.1 Setting forward or reverse rotation The direction of rotation can be selected by operating
the forward / reverse push switch 햴. An interlock prevents operation of the switch while the motor is running. When in the middle position, the on / off switch
is locked.
– Forward rotation: Push the forward / reverse switch
to the right (as seen from the direction in which the
tool is used).
– Reverse rotation: Push the forward / reverse switch
to the left (as seen from the direction in which the tool
is used).
7.2 Screwdriving using the bit adaptor 1.Insert the bit adaptor with TE-C connection end in the
chuck and lock the chuck.
2.Turn the function selector switch to the “drilling” symbol.
3.Set the forward / reverse switch to the desired direction of rotation.
7.5 Switching on and off
Should a sticking drill bit cause the motor to stall for
longer than 2–3 seconds, the tool must be switched
off in order to avoid damage to it.
1. Use the forward / reverse switch to select the direction of rotation.
2. The speed of the tool can be controlled smoothly
between zero and maximum by pressing the on / off
switch slowly.
7.6 Removing the battery (2-finger operation) 1. Press in both release buttons.
2. Pull the battery downwards out of the tool.
7.7 Fitting the battery Use only Hilti B24/2.0 NiCd, B24/2.4 NiCd or B24/3.0
NiMH batteries.
1. Push the battery into the tool from below until it is
heard to engage.
7.8 Charging the battery
The battery cannot be charged through the belt adaptor.
Use only the Hilti C 7/24, C 7/36-ACS or TCU 7/36 chargers.
Incorrect use may lead to electric shocks, overheating
of the battery or leakage of a caustic liquid from the battery.
Read the operating instructions for the charger before
beginning charging.
7.9 Changing the insert tool
-CAUTION●
7.3 Hammer drilling
1. Set the forward / reverse switch to forward rotation
햴.
2. Turn the function selector switch to the “hammer
drilling” symbol 햳.
7.4 Drilling using the quick-release chuck 1. Insert the quick-release chuck with TE-C connection
end in the chuck and lock the chuck.
2. Turn the function selector switch to the “drilling”
symbol.
-CAUTIONA high torque may be transferred to the operator if the
tool stalls while drilling with large-diameter drill bits
and hole saws. Always hold the tool with both hands
on the grips provided.
●
●
The cutting edges of the insert tools
are sharp. The insert tools may also
become hot during use.
There is a risk of cutting or burning
the fingers and hands.
Wear protective gloves when changing insert tools.
7.9.1 Fitting the insert tool 1. Remove the battery from the tool.
2. Check that the connection end of the insert tool is
clean and lightly greased. Clean and grease the connection end if necessary.
3. Check that the sealing lip of the dust shield is clean
and in good condition. Clean the dust shield if necessary or replace the sealing lip if damaged.
17
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
en
4. Turn the chuck ring to the ( ) symbol.
5. Push the insert tool into the chuck as far as it will
go.
6. Rotate the insert tool until it engages.
7. Turn the chuck ring back to the ( ) symbol.
8. Check that the drill bit is engaged by trying to pull it
out of the check.
7.9.2 Removing the insert tool
1. Remove the battery from the tool.
2. Turn the chuck ring to the ( ) symbol.
3. Pull the insert tool out of the chuck.
4. Turn the chuck ring back to the ( ) symbol.
en
8. Care and maintenance
8.1 Care of insert tools
Remove any dirt adhering to the surface of the insert
tools and protect them from corrosion by rubbing them
with an oily cloth from time to time.
8.2 Care of the tool
Before cleaning, remove the battery from the tool in
order to prevent inadvertent starting.
-CAUTIONKeep the power tool, especially its grip surfaces, clean
and free from oil and grease. Do not use cleaning agents
which contain silicone.
The outer casing of the tool is made from impactresistant plastic. Sections of the grip are made from a synthetic rubber material. Never operate the tool when the
ventilation slots are blocked. Clean the ventilation slots
carefully using a dry brush. Do not permit foreign objects
to enter the interior of the tool. Clean the outside of the
tool at regular intervals with a slightly damp cloth. Do not
use a spray, steam pressure cleaning equipment or running water for cleaning. This may negatively affect the
electrical safety of the tool.
8.3 Maintenance
Check all external parts of the tool for damage at regular intervals and check that all controls operate faultlessly. Do not operate the tool when parts are damaged
or when the controls do not operate faultlessly. If necessary, have the tool repaired at a Hilti service center.
Electrical parts of the tool may be repaired only by
trained electrical specialists.
8.4 Care of the battery
Keep the electrical contacts free from dust, oil and
grease. If necessary, use a clean cloth to clean the contact surfaces.
Do not continue to operate the tool until the battery is
completely discharged as this may damage the battery
cells. Recharge the battery as soon as a drop in performance is noticed.
18
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
At monthly intervals or, at the latest, when battery capacity drops significantly, the battery should be conditioned as follows:
– With the C 7/24 or TCU 7/36 charger: Charge for 24
hours in normal charging mode or for 12 hours in
conditioning mode.
– With the C 7/36-ACS charger: The charger detects
automatically whether initial charging or normal charging is necessary.
If, after conditioning, battery capacity is still unsatisfactory, we recommend returning the battery to Hilti
for diagnosis.
8.5 Checking the tool after care and maintenance
After carrying out care and maintenance work on the
tool, check that all protective and safety devices are fitted and that they function faultlessly.
9. Troubleshooting
Fault
Tool doesn‘t run
Possible cause
Battery is discharged or not correctly
fitted
Electrical fault
No hammering action
On / off switch cannot be
pressed
Speed suddenly drops
Function selector switch set to
the wrong mode
Forward / reverse switch is set to
middle position
The battery is almost exhausted.
Battery becomes discharged faster than usual
Battery does not engage
with an audible “click”
Battery condition is not optimal.
Tool or battery overheats
Electrical fault.
Dirt on battery locking mechanism
Overload due to exceeding
application limit
Remedy
Refit the battery. It must be heard to engage
with an audible “click”. Charge the battery if
necessary.
Remove the battery and contact your
nearest Hilti service center.
Set the function selector switch
to hammer drilling mode.
Move the forward / reverse switch to the
left/right.
Stop working with the exhausted battery
and charge it fully.
Charge the battery using conditioning mode
(see battery charger operating instructions).
Clean battery locking mechanism and refit
the battery. Contact your nearest Hilti service center if the problem persists.
Switch off the tool immediately. Remove
the battery and contact your nearest Hilti
service center.
Select the right tool for the application.
10. Disposal
Return waste material for recycling.
Most of the materials from which Hilti power tools are manufactured can be recycled. The materials must be
correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for
taking back your old electric tools for recycling. Please ask your Hilti customer service department or Hilti
sales representative for further information.
Dispose of the battery in accordance with national regulations or return used batteries to Hilti for recycling.
Only for EU countries
Disposal of electric tools together with household waste is not permissible!
In observance of European Directive on waste electrical and electronic equipment and its implementation in
accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
19
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
en
11. Manufacturer’s warranty – tools
en
Hilti warrants that the tool supplied is free of defects
in material and workmanship. This warranty is valid so
long as the tool is operated and handled correctly,
cleaned and serviced properly and in accordance with
the Hilti Operating Instructions, and the technical system is maintained. This means that only original Hilti
consumables, components and spare parts may be
used in the tool.
This warranty provides the free-of-charge repair or
replacement of defective parts only over the entire lifespan of the tool. Parts requiring repair or replacement
as a result of normal wear and tear are not covered by
this warranty.
Hilti is not obligated for direct, indirect, incidental
or consequential damages, losses or expenses in
connection with, or by reason of, the use of, or inability to use the tool for any purpose. Implied warranties
of merchantability or fitness for a particular purpose
are specifically excluded.
For repair or replacement, send tool or related parts
immediately upon discovery of the defect to the address
of the local Hilti marketing organization provided.
This constitutes Hilti's entire obligation with regard to
warranty and supersedes all prior or contemporaneous comments and oral or written agreements concerning warranties.
Additional claims are excluded, unless stringent
national rules prohibit such exclusion. In particular,
12. EC declaration of conformity (original)
Designation:
Type:
Year of design:
Cordless rotary hammer
TE 2-A
2003
We declare, under our sole responsibility, that this product complies with the following directives and standards:
2004/108/EC, 2006/66/EC, EN 60745-1, EN 60745-26, 2006/42/EC, EN ISO 12100, 2011/65/EU, 2004/108/EC.
Hilti Corporation, Feldkircherstrasse 100,
FL-9494 Schaan
Paolo Luccini
Head of BA
Quality and Process Management
Business Area
Electric Tools & Accessories
01/2012
Jan Doongaji
Ececutive Vice President
BU Power Tools & Demolition
20
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
01/2012
Technical documentation filed at:
Hilti Entwicklungsgesellschaft mbH
Zulassung Elektrowerkzeuge
Hiltistrasse 6
86916 Kaufering
Deutschland
Hilti Corporation
Printed: 07.07.2013 | Doc-Nr: PUB / 5137393 / 000 / 00
304444 / A3
304444
Hilti = registered trademark of Hilti Corp., Schaan
W 2842 | 0113 | 10-Pos. 1 | 1
Printed in China © 2013
Right of technical and programme changes reserved S. E. & O.
*304444*
LI-9494 Schaan
Tel.: +423 / 234 21 11
Fax: +423 / 234 29 65
www.hilti.com
Download PDF
Similar pages