OPERATOR'S MANUAL
Cat. No.
0$)
M18™ JOBSITE FAN
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
IMPORTANT SAFETY INSTRUCTIONS
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure
to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
preventative measures reduce the risk of starting
the fan accidentally.
•Avoid accidental starting. Be sure switch is in
the off position before inserting battery pack
or power supply. Inserting the battery pack or
power supply into the fan with the switch on invites
accidents.
•Use only attachments/accessories specified
by the manufacturer.
WORK AREA SAFETY
•Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
•Do not use fan outdoors.
•Do not operate fan in explosive atmospheres,
such as in the presence of flammable liquids,
gases or dust. Fans create sparks which may
ignite the dust or fumes.
•Keep children away while operating fan.
BATTERY TOOL USE AND CARE
ELECTRICAL SAFETY
• Do not attempt to use with any other power
supply or battery.
•Use fan only with specifically designated battery packs. Use of any other batteries may create
a risk of fire.
•Recharge batteries only with the specified
charger for the battery. A charger that may be
suitable for one type of battery may create a risk
of fire when used with another battery.
•When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small metal
objects that can make a connection from one
terminal to another. Shorting the battery terminals together may cause burns or a fire.
•Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
•Do not use fan near water. Never expose the
fan to dripping and splashing. Never immerse
the fan in liquid or allow a liquid to flow inside the
fan. Water entering the fan will increase the risk
for electric shock.
•Unplug the fan during lightning storms or when
unused for long periods. Remove power
supply from outlet when not in use.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they
have
been given
supervision
or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
Exhausted batteries are to be removed from the
appliance and safely disposed of;
if the appliance is to be stored unused for a long
period, the batteries should be removed;
SERVICE
– the supply terminals are not to be
•Refer all servicing to qualified service personshort-circuited.
nel. Servicing is required when the fan has been
PERSONAL SAFETY
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
•Do not overreach. Keep proper footing and
have fallen into the fan, the fan has been exposed
balance of fan at all times. Stable footing on a
to rain or moisture or does not operate normally.
solid surface enables better control of the fan in
Service or maintenance performed by unqualified
unexpected situations.
personnel could result in a risk of injury. •Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelSPECIFIC SAFETY RULES
lery or long hair can be caught in moving parts.
• Maintain labels and nameplates. These carry
FAN USE AND CARE
important information. If unreadable or missing,
contact the store where the product was
•Do not install near any heat sources such as
radiators, heat registers, stoves, or other appara - originally purchased or one of our authorised
tus (including amplifiers) that produce heat.
MILWAUKEE®
service
centres
for
a
•Only operate the fan in a well ventilated area
replacement.
Do not block any ventilation openings.
•Do not operate fan with a damaged or missing
grill.
•Place the fan switch in the off position anddisconnect battery pack or power supply
before making any adjustments, changing
accessories, cleaning or storing the fan. Such
2
WARNING Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and
other masonry products, and
•arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles.
SYMBOLOGY
To reduce the risk of injury, user
must read operator’s manual.
Warning
Double Insulated
Volts
Direct Current
Indoor Use Only
Regulatory
Compliance
Mark
(RCM). Product meets applicable
regulatory requirements.
Cat. No.
0$)
SPECIFICATIONS
DC Volts
18
DC Amps
2.5
REPLACEMENT PART
AC/DC Adapter
FUNCTIONAL DESCRIPTION
4
1
2
5
3
4.Top handle
5.AC/DC power
supply jack
1.Front grill
2.Battery bay
3.Control switch
3
016043003001
ASSEMBLY
OPERATION
WARNING Recharge only with the charger specified for the battery. For specific charging instructions, read the operator’s manual
supplied with your charger and battery.
WARNING Always remove battery pack
before changing or removing accessories.
Only use accessories specifically recommended for this fan. Others may be hazardous.
Inserting/Removing Battery Pack
Insert the battery pack by sliding it into the battery
bay on the front of the fan. Insert the battery pack
until it clicks in place.
To remove the battery pack, push in the release
buttons and pull the battery pack away from the
tool.
WARNING To reduce the risk of fire
or electric shock, do not expose this fan to
water, rain or, moisture.
Battery Pack Protection
To protect the life of the battery pack, the fan will
shut off when the battery’s charge becomes too
low. If this happens, remove the battery pack and
charge it according to the charger’s instructions.
Using the AC/DC Power Supply
Only use MILWAUKEE® 18 volt AC/DC power
supply.
With the battery pack still in place, insert the
connector of the power supply into the 18 volt
DC jack on the back of the fan.
Plug the power supply into a suitable wall outlet.
4
Turning On/Off
To turn the fan On, rotate the control switch from
O to I. To turn the fan Off, return the control switch
to O.
To adjust the speed of the fan, rotate the control
switch between the I, II and III speed postitions.
I - Low
II - Medium
III - High
Adjusting Fan Angle
To adjust the fan angle, grasp fan by the top handle
and tilt fan forwards or backwards. The fan can pivot
forwards to a range of 30°; with detents every 15°.
The fan can pivot backwards to a range of 90°; with
detents every 15°.
Cleaning the Front Grill
Always disconnect the battery pack and
power supply from fan before cleaning. Clean
fan grill periodically with a vacuum wand. For heavy
build up, remove the front grill by removing the
six screws located at the back of the fan along its
outer edges. Dust or wipe grill with a mild soap. Do
not place grill in a dishwasher. Excessive heat can
distort the plastic.
Always reinstall the front
grill before use.
MAINTENANCE
WARNING To reduce the risk of injury,
always unplug the charger and remove the
battery pack from the charger or tool before
performing
any
maintenance.
Never
disassemble the tool, battery pack or charger.
Contact to the store where the product was
originally purchased or one of our authorised
MILWAUKEE® service centres for repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work properly, return the tool, charger and battery pack, to the
store where the product was originally purchased or
one of our authorised MILWAUKEE® service
centres.
WARNING To reduce the risk of personal injury and damage, never immerse your
fan, battery pack or charger in liquid or allow
a liquid to flow inside them.
Cleaning
Disconnect the battery pack and power supply from
fan before cleaning. Clean dust and debris from
charger and tool vents. Keep tool handles clean,
dry and free of oil or grease. Use only mild soap
and a damp cloth to clean the tool, battery pack and
charger since certain cleaning agents and solvents
are harmful to plastics and other insulated parts.
Some of these include gasoline, turpentine, lacquer
thinner, paint thinner, chlorinated cleaning solvents,
ammonia and household detergents containing
ammonia. Never use flammable or combustible
solvents around tools.
Cleaning the Blades
Always disconnect the battery pack and
power supply from fan before cleaning. Remove
the front grill. Wipe blades with a damp cloth. Do not
remove blades. If fan is used in a greasy environment, such as a kitchen, mild soap or a common
household cleaner may be necessary. Do not use
solvents. Do not place in a dishwasher. Excessive
heat can distort the plastic.
Always reinstall
the front grill before use.
Repairs
For repairs, return the tool, battery pack and charger to the nearest service center listed on the back
cover of this operator's manual.
ACCESSORIES
WARNING Always remove battery
pack before changing or removing accessories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
For a complete listing of accessories refer to your
MILWAUKEE® accessories catalogue or go online to
www.milwaukeetools.com.au or www.milwaukeetools.co.nz.
To obtain a catalogue, contact the store where the product
was originally purchased or one of our authorised
MILWAUKEE® service centres.
5
WARRANTY - AUSTRALIA and NEW ZEALAND
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to
product sold in Australia and New Zealand.
AUSTRALIA AND NEW ZEALAND
MILWAUKEE ® Service
MILWAUKEE®prides itself in producing a premium quality product that is Nothing But Heavy Duty®.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, please contact your authorised MILWAUKEE® dealer.
For a list of MILWAUKEE® dealers, guarantee or service agents please contact MILWAUKEE®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 279 624) or visit www.milwaukeetools.com.au /
www.milwaukeetools.co.nz.
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Electric Tool Corporation (Australia)
Techtronic Industries (Australia) Pty. Ltd.
Doncaster, Victoria, Australia, 3108
Milwaukee Electric Tool Corporation (New Zealand)
Techtronic Industries (New Zealand) Pty. Ltd.
Mangere, Auckland, New Zealand, 2022
Professionally made in China for Milwaukee Electric Tool Corporation
Download PDF
Similar pages