USER GUIDE
CLEANVIEW
®
1332, 1327, 1322, 1328 SERIES
*Product images may vary
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.
Always connect to a polarized outlet (one slot is wider than the other). Unplug from outlet when not in use and before conducting maintenance.
When using an electrical appliance, basic precautions should be observed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY:
»Always connect to a polarized
outlet (one slot is wider than the
other). Do not modify the polarized plug to fit a non-polarized
outlet or extension cord.
»Do not leave vacuum cleaner
when it is plugged in. Unplug
from outlet when not in use
and before servicing.
»Do not use outdoors or on
wet surfaces.
»Do not allow to be used as a toy.
Close attention is necessary when
used by or near children.
»Do not use for any purpose other
than described in this User’s
Guide. Use only manufacturer’s
recommended attachments.
»Do not use with damaged cord or
plug. If appliance is not working
as it should, has been dropped,
damaged, left outdoors, or
dropped into water, have it repaired
at an authorized service center.
»Do not pull or carry by cord, use
cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord
away from heated surfaces.
»Do not unplug by pulling on
cord. To unplug, grasp the plug,
not the cord.
»Hold plug when rewinding onto
cord reel. Do not allow plug to
whip when rewinding.
»Do not handle plug or vacuum
cleaner with wet hands.
»Do not put any object into
openings. Do not use with any
opening blocked; keep openings
free of dust, lint, hair, and anything
that may reduce air flow.
»Keep hair, loose clothing, fingers,
and all parts of body away from
openings and moving parts.
»Turn off all controls before
plugging or unplugging
vacuum cleaner.
»Use extra care when cleaning
on stairs.
»Do not use to pick up flammable
or combustible materials (lighter
fluid, gasoline, kerosene, etc.)
or use in areas where they may
be present.
»Do not use vacuum cleaner in an
enclosed space filled with vapors
given off by oil base paint, paint
thinner, some moth proofing
substances, flammable dust, or
other explosive or toxic vapors.
»Do not use to pick up toxic
material (chlorine bleach,
ammonia, drain cleaner, etc.).
»Do not pick up anything that is
burning or smoking, such as
cigarettes, matches, or hot ashes.
»Do not use without filters in place.
»Do not pick up hard or sharp
objects such as glass, nails, screws,
coins, etc.
»Use only on dry, indoor surfaces.
»Keep appliance on a level surface.
»Do not carry the vacuum cleaner
while it is running.
»Unplug before connecting
or disconnecting the TurboBrush®
Tool or TurboEraser® Pet Tool
(on select models).
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
This model is for household use only.
THIS APPLIANCE HAS A
POLARIZED
PLUG
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install a proper outlet. Do not change the plug in any way.
2
www.BISSELL.com
Quick Start Guide
E
D
B
F
C
G
H
I
CARTON CONTENTS
A.
B.
C.
D.
E.
Vacuum Base
Handle
Screws (2)
Hose Wand Clip
TurboBrush®/TurboEraser®
Pet tool (on select models)
F.
G.
H.
I.
J.
Dusting Brush
Hose
Crevice Tool*
Extension Wand
Pet Hair Corner Tool
(on select models)
*Note: Crevice tool is located inside Extension Wand
Assembly
1. Slide handle onto machine base
2. Screw 2 screws into existing holes with Phillips-head
screwdriver
3. Insert hose wand clip into back of vacuum base and
twist clockwise
4. Line up tabs on the cuff of the hose with the notches
on back of vacuum, twist hose clockwise to lock into place
5. Slide other end of hose into hose wand base and place
hose over upper hose wrap on the handle
6. Slide tools into place
*Product images may vary
www.BISSELL.com
3
Thanks for buying a BISSELL vacuum
We’re glad you purchased a BISSELL
vacuum. Everything we know about
floor care went into the design and
construction of this complete,
high-tech home cleaning system.
Your BISSELL vacuum is well made,
and we back it with a limited
three-year warranty. We also stand
behind it with a knowledgeable,
dedicated Consumer Care
department, so, should you ever
have a problem, you’ll receive fast,
considerate assistance.
My great-grandfather invented the
floor sweeper in 1876. Today, BISSELL
is a global leader in the design,
manufacture, and service of high
quality homecare products like your
BISSELL vacuum.
Thanks again, from all of us
at BISSELL.
Mark J. Bissell
Chairman & CEO
4
www.BISSELL.com
Safety Instructions . . . . . . . . . . 2
Quick Start Guide . . . . . . . . . . . 3
Product View . . . . . . . . . . . . . . . 5
Assembly . . . . . . . . . . . . . . . . . . . 6
Operations . . . . . . . . . . . . . . . . 7-9
Maintenance & Care . . . . . . . 9-12
Troubleshooting . . . . . . . . . . . . 13
Replacement Parts . . . . . . . . . . 14
Warranty . . . . . . . . . . . . . . . . . . . 15
Service . . . . . . . . . . . . . . . . . . . . . 15
Product Registration . . . . . . . . 16
Consumer Care . . . . . . . . . . . . . 16
Product View
1
2
15
16
17
18
3
4
6
19
5
7
21
23
22
9
8
20
10
11
12
24
25
26
27
14
13
1Handle
2 Power switch**
3 Tank Release Button
4 Carry Handle
5 Suction Power Indicator**
6 Lid Release Button
7Pre-Motor Filter (located
inside Dirt Tank lid)
8Bottom Easy Empty™
Dirt Tank
9 Cord Rewind
10 Post-Motor Filter
11 Height Adjustment Knob
12 Brush Roll On/Off**
13 Furniture Protection Guard
14Powerfoot
WARNING
Plastic film can be dangerous. To avoid
danger of suffocation, keep away from
babies and children.
15 Cord Clip
16TurboBrush®/TurboEraser®
Pet Tool**
17 Upper Hose Wrap
18 Dusting Brush
19 Stretch Hose
20 Crevice Tool (Grey)
21 Extension Wand
WARNING
Do not plug in your vacuum cleaner until
you are familiar with all instructions and
operating procedures.
22 Extension Wand Clip
23 Power Switch**
24 Hose Wand
25 Hose Wand Base
26 Handle Release Pedal
27 Foot Hose
WARNING
To reduce the risk of electric shock, turn
power switch off and disconnect polarized
plug from electrical outlet before performing
maintenance or troubleshooting checks.
*Product images may vary
** On select models
www.BISSELL.com
5
Assembly
WARNING
The only tool you’ll need to assemble your
vacuum cleaner is a Phillips-head screwdriver.
Do not operate vacuum with damp or wet filters
or without all filters in place first.
Attach handle to vacuum
1. Locate the vacuum handle and remove the
screw packet taped to the handle. The screw
packet contains two screws of equal length.
2.
4.
2. Stand the vacuum upright and slide the
base of the handle firmly into the opening at
the top of the vacuum body.
3. Check to be sure the handle is fitted to the
vacuum body. If there are any gaps between
the handle and the vacuum base, continue to
push the handle firmly into the base until the
handle is flush.
4. Insert the two screws from the screw packet
into the existing holes. Push each screw firmly
into the hole before beginning to secure the
screw with a Phillips head screwdriver. If the
handle is aligned properly on the vacuum base,
you should be able to push the screw almost
entirely into the hole until only the screw head
is visible. Tighten the screw with a Phillips head
screwdriver by rotating the screw clockwise.
Attach vacuum hose, clips & tools
1. Attach the extension wand clip by inserting
the clip into the back of the vacuum base
and twisting clockwise. Mount the extension
wand (with crevice tool inside) on the back
of the vacuum.
1.
5.
2. Attach the Twist ‘n Snap™ hose by lining
up the tabs on the cuff with the corresponding
notches on the back of the vacuum. Twist the
Twist ‘n Snap hose clockwise to lock the hose
into place.
3. Slide the end of the hose wand into the
hose wand base, and fold the hose over the
upper hose wrap.
4.
NOTE: The powerfoot will not suction properly 2.
unless the hose wand is firmly attached.
2.
4. Slide the dusting brush into the opening
below the upper hose wrap.
5. The TurboBrush®/TurboEraser® pet tool
(on select models) secures to the back of
the handle in the mount above the upper
hose wrap.
1.
3.
3.
3.
6
www.BISSELL.com
Operations
Power switch
The Power switch on model 1332, 13321 and
1327 is located on the left side of the vacuum.
Push the rocker switch “ON” (I) to vacuum,
and “OFF” (O) when cleaning is complete.
The Power switch on models 1322 and 1328 is
located on the front of the handle. Push the
button
once to vacuum, and push the button
again when cleaning is complete.
CAUTION
Before using your vacuum, make sure that the dirt
tank is in the locked position and that both filters
(pre-motor and post-motor) are in place. Do not
operate your vacuum without these filters.
NOTE: You can find your model number on the
back, bottom side of the vacuum on the white
sticker by the UL rating.
Handle position
Press the handle release pedal with your foot
to place your CleanView vacuum into one of
three cleaning positions.
1. Upright – For storage and above floor
cleaning with tools.
2. Normal cleaning – Press handle release
for household floor cleaning tasks.
3. Low cleaning – With the vacuum in
normal cleaning position, press handle release
pedal again, use for reaching under low furniture
such as tables, chairs or beds.
Height adjustment
There are five height settings available for
various floor surfaces. Turn the dial on the foot
of the cleaner to the desired setting.
Lowest setting – For low pile carpet or bare
floors. To pick up debris, it may be necessary
to move up one setting.
Medium setting – For medium pile carpet.
Highest setting – For high pile and most
shag carpet.
NOTE: For optimal carpet cleaning performance,
adjust to the lowest practical setting. If your
cleaner is difficult to push, adjust to the next
higher setting.
If the dial is difficult to turn, tilt the cleaner
back slightly to take the weight off the foot
while turning.
Transporting cleaner
1. To move your cleaner from room to room, put
the handle in the upright position, tilt the cleaner
back on its rear wheels and push forward.
2. The cleaner can also be moved by using the
carrying handle.
Tips
*Product images may vary
» Hair, string and small objects can block the
vacuum hose or tools. Check them occasionally
for obstructions.
» Before cleaning under low furniture, check area
first for objects that might harm the unit or block
the vacuum hose.
www.BISSELL.com
7
Operations
Suction Power Indicator
(On model series: 1322 and 1328)
The suction power indicator tells you when the
air flow in your vacuum is reduced due to dirty
filters or a clog in the hose. The suction power
indicator will remain green until the airflow is
reduced. At that time, it begins to change to red.
When it is fully red, the airflow is significantly
reduced by a dirty filter or clog. Follow the steps
on page 12 for clearing a clog. Follow the steps
on pages 9 and 10 to clean your filters. All filters
in the vacuum should be cleaned or replaced
when the clean filter indicator turns red.
Tip
» Hair, string and small objects
can block the vacuum
hose or tools. Check them
occasionally for obstructions.
NOTE: When your vacuum is turned off, the
suction power indicator will go to the green
color setting. The suction power indicator
only detects reductions in airflow when the
vacuum power is on.
Special tools
Your BISSELL CleanView vacuum is not only a
powerful carpet and rug vacuum cleaner, it’s also
a versatile above floor vacuum cleaner when you
select one of the special tools.
1. Raise handle to upright position.
2. Grasp the hose wand and separate from the
hose wand base.
a.
b.
c.
3. Attach tools by firmly pushing onto vacuum
hose or extension wand.
a. Crevice Tool Use in tight narrow spaces.
. Dusting Brush Use brush to dust
b
furniture, blinds, books, lamps, shelves
and baseboards.
Tip
c. Extension Wand Use with desired
attachment for a longer reach.
d. TurboBrush®/TurboEraser® Pet Tool
(model 1328) Use rotating brush action for
small flat areas such as stairs and cushions.
Press gently down and pull toward you in a
raking motion; too much pressure will cause
the brush to stop rotating.
e. Pet Hair Corner Tool (model 1328)
Use tool in corners of room or stairs to pick
up annoying dirt left stuck in the corners.
Automatic Cord Rewind
1. Gently pull out power cord and stop when
yellow is visible. Do not pull power cord beyond
the red line. Plug cord into electrical outlet.
2. To return cord, turn vacuum power switch
off and remove plug from outlet. Hold plug and
press automatic cord button located below the
power switch (on 1332 and 1327 series models)
to wind cord into reel. Do not allow plug to whip
when rewinding.
8
www.BISSELL.com
d.
» The crevice tool is located
inside the wand
e.
WARNING
The rotating floor brush continues to rotate while tools
are in use. To reduce the risk of injury from moving parts,
always move the cleaner with the carrying handle at the
back of the cleaner. Always place vacuum cleaner on floor
with handle in upright position when using tools. Never
place your fingers under the cleaner when it is running.
Never place powerfoot on furniture or uneven surfaces. Do
not place vacuum cleaner close enough to objects to pull
them into rotating brush.
Maintenance & Care
WARNING
To maintain maximum cleaning performance, the
following maintenance steps must be performed:
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
1. Empty the dirt tank when the dirt reaches the
“Full” line on the side. (See page 10)
2. Check the pre-motor filter at least once a
month and clean or replace as needed. To access
the pre-motor filter, remove the Easy Empty
dirt tank from the vacuum base and push the
lid release button located on the carry handle.
Remove the foam filter from the filter tray. On
model 1328 Series, a second small carbon filter
is included here. Replace the second small, black
odor-absorbing carbon filter as needed.
2.
Lid Release
Button
NOTE: Black Carbon Filter is NOT washable.
3. The post-motor filter assists in the filtration
process to return clean air to the room. Replace
the post-motor filter every three to six months.
To access the post-motor filter, remove the
filter tray located below the Easy Empty dirt
tank. When the filter becomes dirty, push the
filter through the bottom of the tray to clean or
replace the filter.
NOTE: The pleated post-motor filter may NOT
be washed with water or detergent. If dust and/
or debris accumulates on the filter, gently tap
the filter on the side of a garbage container.
Note: More frequent filter cleaning or replacing may be necessary if you are vacuuming
new carpet, fine dust, or have allergy concerns.
Follow the instructions on the following pages
to perform these simple maintenance steps.
3.
Post-Motor
Filter Tray
NOTICE
While vacuuming, certain carpets and low humidity
conditions may generate small static discharges. The
discharges are entirely harmless and are not associated
in any way with the main power supply.
www.BISSELL.com
9
Maintenance & Care
WARNING
Empty Dirt Tank
The dirt tank needs to be emptied when the dirt
reaches the “Full” line on the side of the tank.
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
1. Unplug cleaner from electrical outlet.
2. Remove the Easy Empty dirt tank from the
vacuum base by pushing the tank release button.
2.
3.
3. Hold the dirt tank over a garbage container.
Press the bottom lid release button on the back
of the dirt tank to empty dirt.
4. Mount the Easy Empty dirt tank back on the
vacuum base.
NOTE: The dirt tank may be washed in warm
water with a mild detergent. Make sure it is
completely dry before replacing.
Cleaning the pre-motor filter and inner cyclone
Use only genuine BISSELL replacement filters
in your BISSELL CleanView vacuum.
1. Unplug the cleaner from electrical outlet.
2a.
2b.
2.a. Remove the Easy Empty dirt tank and
locate the pre-motor filter as described on
the previous page.
b. Remove the foam filter from the filter
tray. In model 1328 Series, a second
carbon filter is included in here. The filter
tray is fixed in-place, but may be removed
for cleaning by unscrewing the tray. The
foam filter and tray may be hand washed
in warm water with a mild detergent, if
desired. Rinse well, then air dry thoroughly
before replacing the filter. Make sure all
components are completely dry before
replacing. A second black odor-absorbing
filter can also be found here. Replace this
when needed.
NOTE: Black Carbon Filter is NOT washable.
3. The inner cyclone may also be removed for
cleaning. With the bottom of Easy Empty dirt
tank open, reach up into the dirt cup and grasp
the cyclone. Twist the cyclone clockwise to
unlock and pull straight down to remove. Use
the Lock and Unlock Icons on the tank to help
guide the cyclone back in and lock it correctly. It
is important to lock the cyclone back in correctly
as it will impact performance and separation.
The inner cyclone and dirt cup may be wiped
clean with a damp cloth. Make sure all parts are
dry before replacing.
10
www.BISSELL.com
3.
Tip
» When replacing the inner
cyclone after cleaning, open
the pre-motor filter lid to
help guide the inner cyclone
into the grooves at the
top of the tank. Twist
counterclockwise to lock the
inner cyclone into place.
WARNING
Do not operate cleaner with damp or wet filters or
without all filters in place.
NOTICE
Do not place the dirt tank or other product components
in the dishwasher. Hand wash only.
Maintenance & Care
Replacing the post-motor filter
Use only a genuine BISSELL replacement
post-motor filter in your BISSELL CleanView
vacuum.
2.
Post-Motor
Filter
1. Unplug the cleaner from electrical outlet.
2. The post-motor filter assists in the filtration
process to return clean air to the room. Replace
the post-motor filter every three to six months.
To access the post-motor filter, remove the
filter tray located below the Easy Empty dirt
tank. When the filter becomes dirty, push the
filter through the bottom of the tray to clean or
replace the filter.
NOTE: The pleated post-motor filter may NOT
be washed with water or detergent. If dust and/
or debris accumulates on the filter, gently tap
the filter on the side of a garbage container.
Checking rotating floor brush and drive belt
You should check your vacuum cleaner’s rotating floor brush and drive belt regularly for wear
or damage. You should also clean the brush and
brush ends of strings, hair and carpet fibers.
These can wrap around the brush and hamper
its ability to effectively clean your carpet. Also
remove any debris that has accumulated under
the brush cover.
Brush Cover
3.
1. Unplug cleaner from electrical outlet.
2. Place handle in low position and turn vacuum
cleaner over so bottom side is up.
3. Remove the six screws with a Phillips
head screwdriver. Lift the brush cover off.
4. Grasp rotating floor brush at both ends
and lift straight out of the vacuum foot. Slip
off the belt.
5. Clean strings, hair and other debris from
rotating floor brush, paying particular attention
to brush ends.
6. Clean strings, hair and other debris from
motor pulley and drive belt areas.
7. Check drive belt carefully for wear, cuts
or stressed areas, and replace if necessary
(see instructions on following page).
4.
Motor
Pulley
8.
Air
Passageway
8. Check air passageway for obstructions.
Remove debris from this area.
www.BISSELL.com
11
Maintenance & Care
Replace drive belt
WARNING
Use only a genuine BISSELL style 9 replacement
belt (#203-1093) in your BISSELL CleanView
vacuum.
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
1. Unplug cleaner from electrical outlet.
2. With rotating floor brush removed from
vacuum cleaner (steps 1-4 of Check rotating
floor brush and drive belt), grasp old drive
belt and remove from motor pulley. Discard
old drive belt.
4.
Motor
Pulley
3. Place new drive belt over motor pulley and
stretch other end over rotating floor brush in
the space between the bristles.
4. Place ends of rotating floor brush down
into slots on sides as shown.
5. Turn rotating floor brush by hand several
times in the direction of motor pulley. If
properly installed, drive belt will center itself
on rotating brush.
WARNING
To reduce the risk of injury from moving parts, turn
off vacuum cleaner and disconnect Power Plug from
electrical outlet.
6. Reposition the brush cover and screw
all six screws back into place.
Clearing a clog
Low suction or poor pickup may be due to
a clog in the vacuum cleaner. If you notice a
change in the sound of the motor or a reduction
in the spinning action of the dirt or brush roll,
check for clogs.
3.
4.
1. Unplug cleaner from electrical outlet.
2. Remove Easy Empty dirt tank from vacuum
base and empty dirt and debris.
3. Remove inner cyclone from Easy Empty dirt
tank (see page 10) and check for debris build-up
or clogs in the upper tank.
4. Check the suction inlet for a clog.
5.
5. Grasp the hose wand to separate from the
hose wand base. Check for a clog in the base,
the wand or within the hose.
6. Remove the screw attaching the hose wand
base to the vacuum. Straighten the hose wand
base and check for clogs with a long, narrow
object such as a broom stick. Do not use sharp
objects like a clothes hanger, as these may
puncture the hose.
7. If the clog persists, follow the instructions for
Checking the rotating floor brush on page 11 and
inspect the air passageway for obstructions.
12
www.BISSELL.com
6.
Troubleshooting
WARNING
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
Problem
Possible causes
Remedies
Vacuum
cleaner won’t
turn on
Power cord not plugged in
Check electrical plug
Blown fuse/tripped breaker
Check/replace fuse or reset breaker
Incorrect height adjustment
Adjust powerfoot to correct height setting
Hose not attached to suction
opening
Grasp the hose wand and firmly push
into the hose wand base
Crack or hole in hose
Check hose and replace if needed
Broken or worn drive belt
Replace drive belt, see page 11
Rotating floor brush bristles worn
Replace brush
Rotating floor brush jammed
Remove brush and clean debris from
brush ends, see page 11
Clog in vacuum
Follow instructions on page 12 for
clearing clogs
Dirt tank full
Empty dirt tank
Dirt tank or upper tank not
installed properly
Position correctly and lock in place
Filters are dirty
Check and clean or replace pre-motor
and post-motor filters, see pages 9-11
Vacuum
cleaner won’t
pick up dirt
Crack or hole in hose
Check hose and replace if needed
Clog in vacuum
Follow instructions on page 12 for
clearing clogs
Dirt tank full
Empty dirt tank
Dirt tank or upper tank not
installed properly
Position correctly and lock in place
Filters are dirty
Check and clean or replace pre-motor
and post-motor filters see pages 9-11
Vacuum cleaner
difficult to push
Incorrect height adjustment
Adjust powerfoot to correct
height setting
Visible dirt
escaping from
cleaner
Dirt tank full
Empty dirt tank
Filters missing or installed
incorrectly
Check pre-motor and post-motor
filters for correct installation
Knotted or twisted
Follow instructions on page 8
Tool won’t
pick up
Cord will
not retract
Please do
not return
this product
to the store.
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
For any questions or concerns, BISSELL is happy to
be of service. Contact us directly at 1-800-237-7691.
www.BISSELL.com
13
Replacement Parts
These items are available for your BISSELL CleanView Vacuums.
Call 1-800-237-7691 or visit www.bissell.com
PART #
PART NAME
PART #
PART NAME
160-0159
Brush Roll (13.5”)
203-1093
Style 9 Drive Belt
(2-Pack)
203-2664
Hose Assembly, 6’
(1332, 1327 Series)
203-2665
Hose Assembly, 8’
(1322, 1328 Series)
1215
Febreze® Post-Motor Filter*
(Fits all CleanView vacuums)
1008
F ilter pack (includes
one pre-motor filter and
one post-motor filter)
160-1501
Carbon Filter
Accessories
These items are available for your BISSELL CleanView Vacuums.
Call 1-800-237-7691 or visit www.bissell.com
PART #
PART NAME
PART #
PART NAME
203-1429
TurboBrush Tool
203-1527
Dusting Brush
160-1510
TurboEraser Pet Tool
(1328 Series)
160-1966
Pet Hair Corner Tool
(1328 Series)
203-2666
Extension Wand (11”)
203-1056
Crevice Tool
*Febreze® and related trademarks are owned by The Procter & Gamble Company, Cincinnati, Ohio, and used under license by BISSELL Homecare, Inc.
14
www.BISSELL.com
Warranty
Service
Limited Three-Year Warranty
Visit BISSELL.com or contact BISSELL Consumer Care to locate a
BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you
have questions about your warranty, contact BISSELL Consumer Care.
This warranty gives you specific legal rights, and you may also
have other rights which may vary from state to state. If you need
additional instruction regarding this warranty or have questions
regarding what it may cover, please contact BISSELL Consumer Care
by E-mail, telephone, or regular mail as described below.
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon
receipt of the product BISSELL will repair or replace (with new or
remanufactured components or products), at BISSELL’s option, free
of charge from the date of purchase by the original purchaser, for
three years any defective or malfunctioning part.
See information on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial
or rental service. This warranty does not apply to fans or routine
maintenance components such as filters, belts, or brushes. Damage or
malfunction caused by negligence, abuse, neglect, unauthorized repair,
or any other use not in accordance with the User's Guide is not covered.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S
LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
If your BISSELL product should
require service:
Website or E-mail:
www.BISSELL.com
Or Call:
BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8am - 10pm ET
Saturday 9am - 8pm ET
Sunday 10am - 7pm ET
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES
WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE THREE YEAR DURATION FROM THE DATE
OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied
warranty last so the above limitation may not apply to you.
NOTE: Please keep your original sales
receipt. It provides proof of date of
purchase in the event of a warranty claim.
www.BISSELL.com
15
Register your product today!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
BISSELL Rewards Points
Automatically earn points for
discounts and free shipping on
future purchases.
Faster Service
Supplying your information now
saves you time should you need
to contact us with questions
regarding your product.
Product Support
Reminders and Alerts
We’ll contact you with any
important product maintenance
reminders and alerts.
Special Promotions
Optional: Register your email
to receive notice of offers,
contests, cleaning tips and more!
Visit www.BISSELL.com/registration now!
BISSELL Consumer Care
For information about repairs or replacement parts, or questions about your warranty:
Call:
BISSELL Consumer Care
1-800-237-7691
Monday - Friday
Saturday
Sunday
8 am - 10 pm ET
9 am - 8 pm ET
10am - 7pm ET
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of purchase
date in the event of a warranty claim. See Warranty on page 15 for details.
©2014 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 160-3707 Rev 05/14
Visit our website at: www.BISSELL.com
16
Download PDF
Similar pages