CONVENTIONAL FIRE ALARM CONTROL PANEL 1PM2 Series

CONVENTIONAL FIRE ALARM CONTROL PANEL
1PM2 Series
■ Features
1PM2
■ Description
The 1PM2 is a conventional fire alarm panel with a
stylish wall-mount design supplied in 10 to 60 zone
formats. All detector circuits will be indicated with
lighting red LEDs in alarm conditions and flushing
in open circuit fault conditions. Slide-in paper labels
are included for clear zone identification. The alarm
panel has an alarm delay function on every detector
circuits to reduce false alarms, including a zone-byzone settable delay ON/OFF function.
1PM2 features a re-sounding function of panel
buzzer by reception of any subsequence input from
manual alarm stations or other zones ensuring an
announcement of a fire spread after the buzzer
silenced. The alarm panel also has a maintenance
switch to enable installation or maintenance works
to cut off the panel buzzer and zone alarms.
1PM2 to be equipped with a CPU for securing high
reliability features also a CPU trouble back-up function.
Even when the CPU falls down, basic functions are
secured to indicate alarm zones, to sound alarms and
to transmit the alarm signal.
The power consumption reduced 70% compared with
Nittan’s previous models contributes to cost reduction.
•
10 to 60 zone model available
•
Extra slim design
•
Highly reliable design by adopting durable LED
indicators and CPU
•
10 to 20 circuits for zone alarm bells available
(depends on the model on purchased)
•
Alarm delay function
•
Alarm delay ON/OFF switch function
•
Trouble monitoring function
•
CPU trouble back-up function
•
Re-sounding mode of a panel buzzer
•
Equipped with high protection for Lightning surge
•
Interrupting function for emergency announcements to silence zone alarms
•
3 alarm indicators for indicating the alarm inputs
from building facilities such as hydrants
•
CPU trouble back-up function
•
Capability of transmitting the second fire signal
•
Signal transmit for Emergency PA facility also
equipped
•
Easy wiring by Push-in terminals’ one-touch
connection
■ Remote Test Function
Remote test function is available on 2KAH3-P and
2KAD3-P detectors etc. with a dedicated testing
device.
2KAH3-P
- Distinguishes steam
and smoke
- Automatic sensitivity
compensation
- Suitable for Shower
rooms and Kitchens
* Operating Image
2KAD3-P
- Remote-test available
- Automatic sensitivity
compensation
- Suitable for Condominiums
NOT TO BE USED FOR INSTALLATION PURPOSES.
Nittan reserves the right to make changes at any time without notice in prices, colours, materials,
components, equipment, specifications and models and also to discontinue models.
1PM2-DAT-01
Rev.1
■ Main Features
1. High reliability, advanced fire detection
Re-sounding mode of panel buzzer
CPU trouble back-up function
After Panel alarm silence
by operator at fire, the
panel buzzer automatically
re-sounds by operation of
manual alarm stations or by
receipt of alarm signal from
other zones to announce fire
spread.
Alarm delay ON/OFF function
Even when CPU is down,
basic function is carried on,
fire signal can be received,
zone indication, alarm
sounding, fire alarm signal
transmission, etc.
Outputs for Emergency PA system
Alarm delay function can
be cancelled zone by zone
individually.
Outputs for interlocking to
Emergency PA system are
provided as standard.
2. Advanced functions for easy installation and maintenance
Maintenance switch (All alarm silence)
Lightning surge protection
At maintenance work,
unnecessary alarm sounding
can be cut off by operating the
maintenance switch (except
telephone calling sound).
Clicking sounds is made when
the maintenance switch is ON
to draw operator’s attention.
Lightning surge protection
devices are provided as
standard to main circuits to
protect semiconductor parts.
Push-in type terminals
Alarm delay ON/OFF switch
Push-in type terminals
are employed to improve
efficiency at installation.
This switch can make
the alarm delay function
ineffective for installation and
mainenance work.
Self-checking function
Auto reset switch
When operation test of
detectors and manual alarm
stations are conducted, by
pressing auto reset switch to
the reset side, fire test can
be conducted zone by zone
and the tested detector and
the control panel shall be
automatically reset.
Monitoring;
• Detector line open-circuit
• Circuit voltage low
• CPU trouble
• Fuse blow
• Disconnection of Standby battery
• Emergency PA line open-circuit
.
NOT TO BE USED FOR INSTALLATION PURPOSES.
Page 2 of 6
1PM2-DAT-01
Rev.1
■ Indicators on Operation Panel
[6]
[7]
[1]
[2]
[10]
[15]
[3]
[11]
[16]
[4]
[12]
[5]
[13]
[8]
[18] [19]
[17]
[14]
[9]
[20] [21] [22]
[23]
[1] FIRE (Red)
LED turns on when the panel is in an alarm condition.
[2] AC POWER (Green)
LED turns on when AC power is supplied to the main power circuit.
[3] CIRCUIT VOLTAGE (Green)
LED turns on as long as the main circuit voltage of the control
panel is within acceptable levels (approx. 20.4 V and greater).
[4] SWITCH OPERATION (Red)
LED flashes when the panel switches are ON or not normal state.
[5] TELEPHONE (Green)
LED turns on when a handset is plugged into a telephone jack of
a manual alarm station or an annunciator panel.
[6] MAINTENANCE (Red)
LED turns on during a maintenance mode.
[7] ZONE ALARM SILENCE INDICATOR (Red)
LED flashes when zone alarms are silenced.
[8] PANEL ALARM SILENCE switch
Activation of this switch when a panel buzzer is sounding, turns
off the sounding buzzer.
[9] ZONE ALARM SILENCE switch
Activation of this switch makes zone alarms silenced.
[10] ALARM DELAY (Red)
LED turns on during a delay time of 60 sec, and flashes during
a general alarm delay switch is OFF.
[11] CPU TROUBLE (Red)
LED turns on when the CPU is in a fault state.
[12] FUSE FALUT (Red)
LED turns on when a fuse for zone alarm outputs is blown.
[13] BATTERY FAULT (Red)
LED turns on when a standby battery is not connected to the
panel.
[14] EMERGENCY PA (Red)
LED flashes during emergency PA announcements, and turns
on when an open circuit is detected on the emergency PA lines.
[15] MANUAL ALARM STATION (Red)
LED turns on when a manual alarm station is
activated.
[16] HYDRANT OPERATION (Red)
LED flashes while a hydrant pump(s) is in operation.
[24]
[25]
[26] [27]
[17] Other Alarms (Red)
Each of the LEDs turns on when the panel receives alarm signals
from building facilities via LXn-C contacts.
[18] RESET switch
Activation of this switch resets the panel condition.
[19] ALARM TRANSMISSION ISOLATION switch
Activation of this switch isolates an alarm signal transmission
through GA-GB-GC contacts.
[20] GENERAL ALARM switch
Activation of this switch activates all the zone alarms and outputs
alarm signals to an emergency PA facility.
[21] HYDRANT STATION ISOLATION switch
Activation of this switch isolates an alarm signal transmission
through H-H’ contacts.
[22] EMERGENCY PA ISOLATION switch
Activation of this switch isolates an alarm signal transmission to
an emergency PA facility.
[23] FIER TEST switch
Use this switch for conducting a fire indication test.
[24] ZONE SELECTION TENS DIGIT switch
This switch sets tens digit of testing zones during a fire indication
test.
[25] ZONE SELECTION ONES DIGIT switch
This switch sets ones digit of testing zones during a fire indication
test.
[26] AUTO RESET switch
Activation of this switch enables a non-latching test function which
allows manual alarm stations and detectors to be tested and the
panel to resets automatically.
[27] BATERY TEST switch
Activation of this switch enables a standby battery test.
NOT TO BE USED FOR INSTALLATION PURPOSES.
Page 3 of 6
1PM2-DAT-01
Rev.1
■ Typical Wiring Diagram
T
L1
For Detectors
and
Manual Alarm Stations
L
Fire Alarm Zones (24 VDC+)
Fire Alarm Common (-)
Telephone (+)
Response Lamp (24 VDC+)
Fixed Temp.
Heat
Ln
C
T
A
I1
For Announciator
For Fire Alarm Signal
Transmit
For Reset Pulse
Transmit
For Building Facilities
For Zone Alarm Bells
For Emergency PA
System
For Indication Lamps
For Hydrant Pump
Starter
For Primary Power
Source
For Earth Connection
L
ROR
Heat
C
Smoke
C
C
T
C
I1
L
S
C
P
*1 CRE *2
P
L *3
I+
Fire Alarm Zone Indication (-)
In
Announciator Buzzer Silence (-)
IC
Announciator Buzzer (-)
IB
Announciator Power Supply (24VDC+) I+
Common Fire Alarm Signal
F
(Works compulsorily)
F'
F
F’
Fire Alarm Signal
GA
(Isolation switch
GB
available)
GA GC GB
GC
N
Normally Closed
(System Reset=Transmit a pulse)
N'
LX1
Other Alarm Input
LX2
LX3
Other Alarm Common
C
Other Alarm Signal Transfer
XA
(Non-Voltage, N/O)
XC
XA
XC
B1
Zone Alarm Output (24 VDC+)
Bm
Zone Alarm Common (-)
BC
EA1
Zone Block Output
EAn
For Emergency PA Common
EC
First Alarm Signal Transfer
EF1
Second Alarm Signal Transfer
EF2
EB
Microphone Operating Input
(Silences zone alarms)
EB'
PL
Power Output (25 VAC)
PL'
Output for Start
H
(Non-Voltage, N/O)
H'
H
H’
Input for Confirmation of Start
XL
(Pump Activation=25VAC Input)
XL'
P1
Power Input (220 VAC)
P2
E
L
A
F
F'
Announciator
In
IC
IB
I+
N
N'
Fire Protection
System, etc.
Security System, etc.
Fire Extinguishing
System, etc.
B
B
B
*4
EL1
ELn
EC
EF
EB
EB'
*5
LED
Emergency
PA
System
LED
H
H'
XL
XL'
Hydrant
Pump
Starter
AL
LED
LED
AL'
220 VAC
Exclusive
Power supply
*1: P = Manual Alarm Station
*2: The CRE is a dedicated end-of-line device which comes with the 1PM2 fire alarm control panel.
*3: Make sure to be used F-F’ and N-N’ terminals when use Remote indication lamps.
*4: Use the motor bells rated at 10 mA, 24 VDC.
*5: The end-of-line resister comes with the 1PM2 fire alarm control panel.
NOT TO BE USED FOR INSTALLATION PURPOSES.
Page 4 of 6
1PM2-DAT-01
Rev.1
■ Dimensions
20 zones cabinet
450
40 zones cabinet
100
60 zones cabinet
450
450
100
1250
1060
760
100
Specifications
1PM2-nLA
Number of Zones
10
20
Number of Bells (10 mA)
30
40
20
Number of Bell Blocks
50
60
30
10
15
Primary Rated Current (220VAC)
20
0.39 A
Standby Battery
0.45 Ah
1.2 Ah
Mounting Type
Wall-mounting type
Dimensions (mm)
W 450 x H 760 x D 100
W 450 x H 1060 x D 100
W 450 x H 1250 x D 100
Weight
18 kg
25 kg
30 kg
Notes
Not included: Dedicated Battery, Telephone Handset
■ Ordering Information
Model
PTL-1
Description
Telephone Handset
Nicd-battery (0.45AH)
Ni-Cd Battery (0.45AH) for 1PM2-10LA – 30LA
Nicd-battery (1.2AH)
Ni-Cd Battery for (1.2AH) for 1PM2-40LA – 60LA
PSH-nL
Annunciator Panel with n Zone
2KH2-LS
Optical Smoke Detector
CKLD-KPT
LP05
1CD-70-LS
2SC-LS
Beam Type Smoke Detector
Remote Station for Beam Detector
Fixed Temp. Heat Detector, 70°C
Rate of Rise Heat Detector
2KAH3-P
Dual Wavelength Type Optical Smoke Detector with Remote testing function
2KAD3-P
Optical Smoke Detector with Automatic sensitivity compensation and Remote testing function
MTS2
Remote Testing and Address Setting Device for 2KAH3-P, 2KAD3-P and others
LP01/1
Remote Station for MTS2
3T
Common detector Base for LS type detector
B6T2
Common detector Base for LS type detector for connecting a remote indication lamp
B3-J
Detector Base for 2KAH3-P, 2KAD3-P, and others
1MF1A
Manual Alarm Station with telephone jack
BD-6-24-11
Local Alarm Bell (10 mA)
PL-R4-LED
Indication Lamp (LED type)
AL-4-24
SRT-01M6L-47SGB
Remote Indication Lamp
Local Combined Box (vertical type) with telephone jack c/w Surface Mounting Box
NOT TO BE USED FOR INSTALLATION PURPOSES.
Page 5 of 6
1PM2-DAT-01
Rev.1
■ Specifications
Specifications
AC Power
Standby Battery
1PM2-nLA
220 VAC ±10% 50/60 Hz
Sealed Type Ni-Cd battery
10LA - 30LA Panel
: 0.45 Ah
40LA - 60LA Panel
: 1.2 Ah
Power Consumption
39 VA
Nominal Delay Time
60 sec. (For smoke detector: 60 sec. For heat detector: 20 sec.)
Dimensions
LED Indicators
Functions
External Line Resistance
End of Line Device
Panel Alarm Sounder
Trouble Alarm
Fire Alarm Transmission
10L - 20L Panel
30L - 40L Panel
50L - 60L Panel : W 450 x H 760 x D 100 mm
: W 450 x H 1060 x D 100 mm
: W 450 x H1250 x D 100 mm
Fire alarm, AC power, Circuit voltage, Switch operation, Telephone, Maintenance, Zone alarm silence, Alarm
delay, CPU trouble, Fuse fault, Battery fault, Emergency PA, Manual alarm station, Hydrant operation,
Other alarm (3 windows)
CPU fault monitoring, Fuse fault indication, Cable break monitoring
50 Ω and less
CRE
Piezoelectric buzzer, automatic re-sounding type
Detector line open-circuit, CPU trouble, Zone Alarm Fuse blows, No battery connected, Emergency PA line
open-circuit, Alarm inputs from external equipment
Contact Capacity
Common Fire Alarm
: F-F’ (Normally-Open)
1 A 24 VDC
Fire Alarm
: GA-GB-GC (Form-C)
1 A 24 VDC
Reset Pulse
: N-N’ (Normally-Close)
1 A 24 VDC
External Equipment Alarms: XA-XC
1 A 24 VDC
Emergency PA : EC EF1 EF2 EA1-EAn* EB EB’
(Normally-Open)
1 A 24 VDC
*n: 10LA=10, 20LA-40LA=15, 50LA-60LA=20
Output Current for Zone Alarms (Bell)
24 VDC
10LA-30LA: 200 mA
Output Current for Indication Lamps
25 VAC
400 mA
40LA-60LA: 300 mA
Number of Connectable Detectors
Standard type Smoke detector:
Heat detector:
Thermistor type Heat detector:
Detectors with test function: Connectable Manual Alarm Station
1MF1A 1MI1A
Connectable Annunciator Panel
Operating Temperature
Primary Materials
Body Color
Max. 40 /zone, Total 20 x zones
As required
Max. 24 /zone, Total 12 x zones
Max. 20 /zone, Total 10 x zones
Model PSH x 1 unit
0°C to +40°C
Main Body: SPCC t1.6
Door: SPCC t1.2
Operation Panel: Flame retardant resin
JPMA Color Code A22-90B Semi-gloss (off-white)
Page 6 of 6
1PM2-DAT-01
Rev.1
Download PDF
Similar pages