GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
GT480
C o n t r o l Pa n e l
User Instructions
19/07/2007
17:18
Page 1
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Display Status Blanking . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT USER INFORMATION . . . . . . . . . . . . . . 2
Full Setting the System . . . . . . . . . . . . . . . . . . . . . . . . 3
Setting & Unsetting the System via a Keyswitch . . . . . . 3
Pre Exit Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Part Setting the System (using Part 1) . . . . . . . . . . . . . 4
Part Setting the System (using Part 2 or 3) . . . . . . . . . . 5
Unsetting the System . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Display After Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Resetting After Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Tamper Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the System with Mains Fail . . . . . . . . . . . . . . . . 10
Programming User Codes . . . . . . . . . . . . . . . . . . . . . . 12
Programmable User Options . . . . . . . . . . . . . . . . . . . . 15
Zone Remove Option . . . . . . . . . . . . . . . . . . . . . . . . . . 15
System Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Turning Chime On/Off . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting Time & Date . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Reading the Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Keypad Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Keypad Tamper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tamper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
System Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
19/07/2007
17:18
Page 1
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Introduction
Welcome to the GT480 control panel. Your installation company will
have programmed your system to protect your premises to the highest
possible standards. Several user programmable options are available
that will be covered later in this manual. Throughout this manual
reference will be made to the Master User Code. The factory set
default is 5678. This code is programmable along with eight other User
Codes.
If an Engineer is on site, it may be necessary to authorise them to
access your system. Do this by entering your User Code when
asked to do so by the engineer.
One of two types of Keypad may be fitted to your system, the first type
has Text on the keys for example Yes and No Keys. The second type
uses Icons and is designed to be multi-lingual (see table below).
Icon style keypad
Text style keypad
Full
Part
Quick
Yes
No
! ! ! IMPORTANT ! ! !
The Keypad may have ‘Icon’ style keys
instead of ‘Text’ style keys. Please use
the table above for a conversion of the
different styles. This will be reflected in
this manual, for example.
Press Yes (
)
Pa g e 1
17:18
Page 1
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Display Status Blanking
Depending on Control Panel installed, it may be a requirement that
the Status (Set or Unset display) of the security system is not
displayed. Set or Unset Status will only be displayed for ten seconds
when the system is Set or Unset. The bottom line of the display will
then be blanked off.
I
IMPORTANT USER INFORMATION
If the Control Panel is non EN then all displays will be shown and
“CHECK” will not be displayed.
All information displays will remain until cleared by the User.
Pa g e 2
17:18
Page 2
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Full Setting the System.
After checking the premises are secure:
1)
Enter a valid User Code followed by Yes (
).
2)
The exit tone will now sound.
3)
Exit the premises via an authorised exit route.
4)
Once the premises are secure, listen (from outside the
protected area) for the exit tone to finish.
Note:
To abort the exit, enter a valid User Code.
Setting & Unsetting the System via a Keyswitch (if fitted).
Biased Keyswitch
To set the system with a biased keyswitch, insert the key and turn it,
then return the key to the original position and remove. Follow the
instructions from step 3 (above).To unset, repeat this operation.
Pa g e 3
17:18
Page 3
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
Pre Exit Check.
At the start of the setting procedure, a fault
tone will sound if any non exit routes are
open. The display will show, for example:-
19/07/2007
Exit Now ! . . .
Zone 3
If the fault clears within 20 seconds then the exit tone will begin, if not,
the fault tone will continue until a valid User code is entered.
Part Setting the System (using Part 1).
Up to three Part Sets may be available for your system. Please refer to
the customer details at the rear of this manual for information about
Part Set zones. Part Set zones will be omitted from the system when
that particular Part Set is used. To set the system using Part 1.
1)
Enter a valid User Code followed by 1 (
2)
Retire to an unprotected area.
Note:
To abort the exit, enter a valid User Code.
Pa g e 4
).
17:18
Page 4
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Part Setting the System (using Part 2 or 3).
Two other Part Sets may be available for your system. Part 2 is a
second set of zones that may be omitted and Part 3 will combine Part
1 and Part 2. To use Part 2 or 3.
1)
Enter a valid User Code followed by 2 or 3.
2)
Retire to an unprotected area.
Note:
To abort the exit enter a valid User Code.
3)
The exit tone may or may not be heard depending on the
system settings programmed by the installation company.
4)
Exit the premises or retire to an unprotected part of the
system. At the end of the exit time, either the exit sounder
will stop (if the exit tone has been audible) or a single beep
will be emitted (if the exit tone has been silent).
5)
The system is now Part Set. You are free to move around the
zones that have been removed by the Part Set but other
zones on the system are active.
Pa g e 5
17:18
Page 5
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Unsetting the System.
1)
Enter the premises via an authorised Entry Point.
2)
The entry tone will sound.
3)
Proceed to the keypad and enter a valid User Code.
Display After an Alarm.
If an alarm occurs when the system is Set, the cause of the alarm will
be displayed for 10 seconds after you unset the system.
1)
The display will show, for
example:-
! ! ! ALARM 4 ! ! !
Zone 4
2)
Then, after 10 seconds the display
will show:-
! ! ! ! CHECK
3)
To view the cause of the alarm again, enter your User code.
Then press 0.
Pa g e 6
!!!!!
17:18
Page 6
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Resetting After an Alarm
After an alarm the system needs to be reset.
Your installation company will have programmed the reset modes for
your system so that it complies with your insurance company and to
legislation requirements.
Your installation company will have informed you as to the type of
reset that your system is set for.
Before attempting to reset your system, ensure that the system
is Un-set and the fault has been rectified.
1)
If the system has been
programmed for Any code reset;
2)
With the display showing:Enter your User code.
Then press Yes (
).
The exit tone will sound and the
display will show:-
3)
! ! ! ! CHECK
Exit Now ! . . .
Ok !
Enter your User code again to abort the setting.
The system is now reset.
Pa g e 7
!!!!!
17:18
Page 7
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
If a Master Code Reset has been programmed by the engineer, a
higher level of code will be required.
If Alarm Reset has been programmed for Master, then the display will
show, for example, ! ! ! ALARM 4 ! ! ! each time the User attempts to set
Zone 4
the system.
Use a Master code to reset the system.
1)
With the display showing:Enter a valid Master code.
Then press Yes (
! ! ! ! CHECK
!!!!!
).
Exit Now ! . . .
Ok !
2)
The exit tone will sound and the
display will show:-
3)
Enter your Master User code again to abort the setting.
The system is now reset.
If an Engineer Code Reset has been programmed, please call the
Installation Company.
If Alarm Reset has been programmed for Engineer, then the display
will show, for example, ! ! ! ALARM 4 ! ! ! each time the User attempts to
Zone 4
set the system.
Pa g e 8
17:18
Page 8
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
If Anti has been programmed for Alarm Reset, contact the Central
Station or Engineer, (as instructed by the Installation Company) and
quote the number given by the display.
1)
The central station or engineer will give a return
Anti-Code, (this may contain the YES (
for example: 5, YES (
2)
) & NO ( ) keys
), 2, 4.
Enter this Anti-Code into the keypad.
The system is now reset.
Tamper Reset
If a fault or tamper occurs when the system is in Day (Unset) mode, the
fault sounder will operate. The display will
! ! ! ! CHECK ! ! ! ! !
show:1)
2)
To view the cause of the fault, enter
your User Code.The display will
show, for example:The message will stay on the
display for 10 seconds or until you
press the 0 key. The display will
then return to:-
! ! ! ! CHECK
Tamper
!!!!!
! ! ! ! CHECK
!!!!!
After the cause of the fault has been rectified, the system will need to be reset.
The terms of your insurance may prohibit User reset. If Tamper
Reset has been programmed for Engineer Reset the display will
show ! ! SERVICE DUE ! for 10 seconds each time the user
attempts to set the system. Please contact your installation
company.
Pa g e 9
17:18
Page 9
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Tamper Resetting
1)
With the display showing:Enter a valid User code.
Then press Yes (
! ! ! ! CHECK
!!!!!
).
2)
The exit tone will sound and
the display will show:-
3)
Enter your User code again to abort the setting.
Exit Now ! . . .
Ok !
The system is now reset.
Setting the system with Mains Fail
In the event of a short term power cut, where it is known when power
will be restored, (e.g. Engineers working on power lines that affect
your premises) it might be necessary to set the system. Please follow
the steps outlined below:
1)
With the display showing:-
2)
Enter your User code. The display
will show:-
Pa g e 1 0
! ! ! ! CHECK
!!!!!
! ! ! ! CHECK
Mains Flt
!!!!!
17:18
Page 10
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
3)
Enter a your User Code again followed by Yes (
4)
The exit tone will now sound.
5)
Exit the premises via an authorised exit route .
Note:
To abort the exit, enter a valid User Code.
19/07/2007
).
If Part Setting
! ! ! ! CHECK
!!!!!
! ! ! ! CHECK
Mains Flt
!!!!!
1)
With the display showing:-
2)
Enter your User code. The display
will show:-
3)
Enter a your User Code again followed by 1, 2 or 3.
4)
The exit tone will now sound.
5)
Retire to an unprotected area.
Note:
To abort the exit, enter a valid User Code.
Pa g e 1 1
17:18
Page 11
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Programming User Codes
Up to nine user codes may be programmed on predetermined levels.
These are.
User Numbers 1 to 3 Master Level.
Allows Set, Part Set, Unset and User Programming Mode.
User Numbers 4 to 7 User Level.
Allows Set, Part Set and Unset.
User Numbers 8 to 9 Set Only Level.
Allows Set Only
User Number 1 is factory default 5678. This code may only be
changed, there is no facility for deleting this code.
All other codes may be changed or deleted as required.
To program User Codes.
1)
Enter a valid Master User Code
followed by No ( ).
The display will show:2)
Press No ( ).
The display will show:-
3)
Press No ( ). The display will
show:-
4)
Press Yes (
show:-
Do You Want to. .
Test ?
Do You Want to. .
Delete Zone ?
Do You Want to. .
Select Options ?
). The display will
Do You Want to. .
Program Chime ?
Pa g e 1 2
17:18
Page 12
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
5)
Press No ( ).
The display will show:-
6)
Press Yes (
).
The display will show:-
7)
Press a single digit corresponding
to the user number (1 to 9) that
you wish to program.
The display will show for example:-
8)
9)
To change the code press No ( ).
The display will show,
for example:(To delete a code enter 0000).
10)
Do You Want to. .
Program Codes ?
Select
1..9
Code 2
####
Code 2
0 0 0 0 <-
Enter your required code,
followed by Yes (
).
The display will show for example:-
Code
2 Text
User 2
Code
-
2 Text
To accept the current text press
Yes (
)
or
To change the text press No ( ).
The display will show for example:-
Pa g e 1 3
19/07/2007
17:18
Page 13
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
11)
19/07/2007
Text is entered in a similar way that you would enter text on
a mobile telephone. Select characters from the list below:1
3
5
7
9
=
=
=
=
=
ABC
GHI
MNO
STU
YZ blank
2
4
6
8
0
=
=
=
=
=
DEF
JKL
PQR
VWX
1234567890
Enter the required character followed by Yes (
).
Continue until you have entered
eight characters.
12)
The display will show:-
13)
Press Yes (
Do You Want to. .
Program Codes ?
) to program more codes
or
Press 0 twice to return to the Unset Mode.
Pa g e 1 4
17:18
Page 14
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Programmable User Options
Several user programmable options are available via user codes 1, 2
or 3. To use these options please follow instructions below.
Delete Zone Option
This option allows individual zones to be deleted (omitted) when the
system is being set. Note: Zone delete is only effective for one Set and
will need to be repeated for subsequent Sets. If you are removing
particular zones on a regular basis ask your installation company to
include them in a Part Set.
The system will reinstate the detectors and set normally the next time
you set the system.
1)
Enter a valid Master User Code
followed by No ( ). The display
will show:-
2)
Press No ( ).
The display will show:-
Do You Want to. .
Test ?
Do You Want to. .
Delete Zone ?
3)
Press Yes (
).
The display will show:-
Enabled Zones . . .
12345678
4)
Press the zone numbers
corresponding to the zones you
wish to delete from the set
procedure. The display will
show, for example:-
Enabled Zones . . .
1-345-78
Pa g e 1 5
17:18
Page 15
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
5)
6)
Press 0 twice.
The display will show for example:-
Press
or
Press
or
Press
or
Press
Yes (
19/07/2007
Do You Want to. .
Set User 1 ?
) for Full Set
1 for Part 1 Set
2 for Part 2 Set
3 for Part 3 Set
7)
The system will now start the relevant Set, with the zones
you deleted removed from the Set.
Note:
This will be for the one Set state only.
System Test
This option allows the User to test zones, bells and strobes on the
system.
1)
Enter a valid Master User Code followed by No ( ).
The display will show:Do You Want to. .
Test ?
2)
Press Yes (
).
The display will show:Walktesting . . . . .
O.k !
Pa g e 1 6
17:18
Page 16
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
3)
Walk around the area being tested. As each device is
operated, there will a tone from the internal sounders and
the display will show the triggered circuit.
4)
To test the bells (external sounders) and strobe press 9.
To stop the bell test press 9 again.
5)
To escape back to Unset press 0 three times.
Turning Chime On/Off
Your installation company may have programmed the system so that a
chime tone sounds when certain doors are opened, or a detector is
triggered. This Chime function may be turned on or off by the User.
1)
Enter a valid Master User Code
followed by No ( ).
The display will show:-
Do You Want to. .
Test ?
2)
Press No ( ).
The display will show:-
Do You Want to. .
Delete Zone ?
3)
Press No ( ).
The display will show:-
4)
Press Yes (
).
The display will show:Press Yes (
5)
Do You Want to. .
Select Options ?
Do You Want to. .
Program Chime ?
)again.
The current Chime Mode will be displayed. Use the No ( )
key to change it to the mode you require. When finished
press 0 three times to return to the Unset mode.
Pa g e 1 7
17:18
Page 17
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Setting Time & Date
1)
Enter a valid Master User Code
followed by No ( ).
The display will show:-
Do You Want to. .
Test ?
2)
Press No ( ).
The display will show:-
Do You Want to. .
Delete Zone ?
3)
Press No ( ).
The display will show:-
4)
5)
Press Yes.
The display will show:-
Do You Want to. .
Select Options ?
Do You Want to. .
Program Chime ?
Press No ( ).
The display will show:Do You Want to. .
Program Codes ?
6)
7)
8)
Press No ( ).
The display will show:-
Press Yes (
).
The display will show:-
Do You Want to. .
Set Date / Time ?
Type
0000
Day / Mnth
Enter the Day and Month e.g 0307 for 3rd July followed by
Yes (
).
The display will show:Type
0000
Pa g e 1 8
Hrs / Mins
17:18
Page 18
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
9)
19/07/2007
Enter the time using the 24 Hour clock e.g 2300 for 11pm
followed by Yes (
).
The display will show,
for example:-
10)
Press Yes (
) to accept.
The display will show:-
11)
To return to the Unset Mode
press 0 twice.
03 Jul
Ok ?
23: 00
Do You Want to. .
Set Date / Time ?
It should be noted that the time displayed after setting the time may
be plus or minus one minute.
Pa g e 1 9
17:18
Page 19
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Reading the Log
1)
Enter a valid Master User Code
followed by No ( ).
The display will show:-
2)
3)
4)
5)
6)
7)
8)
Do You Want to. .
Test ?
Press No ( ).
The display will show:-
Do You Want to. .
Delete Zone ?
Press No ( ).
The display will show:-
Do You Want to. .
Select Options ?
Press Yes (
).
The display will show:-
Do You Want to. .
Program Chime ?
Press No ( ).
The display will show:-
Do You Want to. .
Program Codes ?
Press No ( ).
The display will show:-
Do You Want to. .
Set Date / Time ?
Press No ( ).
The display will show:-
Do You Want to. .
View Log ?
Press Yes (
).
The display will show the last event in the Log. Whilst
viewing the log pressing No ( ) will display the previous
event. Pressing Yes (
) will display the next event.
Pa g e 2 0
17:18
Page 20
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
9)
To return to the Unset Mode press 0 three times.
Note:
EN control panel only.The the log may store up to 256
events with time and date stamp.
Note:
Non EN control panel. Depending on the Log mode
programmed by your installation engineer the log may store
256 events with no time or date stamp.
or
64 events with time and date stamp.
Keypad Alert
If programmed by your installation company, alarm keys,
when
pressed together will act as alert keys. The exact function will depend
on what they have been programmed for. If they are programmed as
panic, for example, pressing them will activate the alarm when the
system is set or unset.
Keypad Tamper
The keypad will monitor the number keys that are pressed without a
valid User Code being entered. More than 24 key presses will cause a
keypad tamper. This will be displayed as ! ! ! ! CHECK ! ! ! ! ! and will
require a valid User Code entry to stop the sounders. The display will
then show. ! ! ! ! CHECK ! ! ! ! !
KP Tamper
If the system was Unset only the internal sounders will operate. If the
system was Set, a full alarm will be generated.
Tamper
Provision is provided by the control panel for all keypads, cabling and
detectors to be tamper protected. With the system Unset most
tampers will cause an internal alarm, whilst the system is Set a full
alarm will be generated by a tamper.
Pa g e 2 1
17:18
Page 21
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
System Details
Installation By:
Address:
Tel:
Fax:
Zone No.
Location
1
2
3
4
5
6
7
8
Installation Date
Serviced
Next Due
Type
Chime
Service Timer
Serviced
Notes
Pa g e 2 2
Pt1
Pt2
On
Off
Next Due
17:18
Page 22
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
Notes:
Pa g e 2 3
19/07/2007
17:18
Page 23
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
Notes:
Pa g e 2 4
19/07/2007
17:18
Page 24
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
Notes:
Pa g e 2 5
19/07/2007
17:18
Page 25
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
Risco Group UK Ltd
Internet: www.riscogroup.co.uk
Risco Group UK Ltd reserve the right to amend the software and features without prior notice
Installed By:-
5IN480UM B
PR5831 Rev1.1
17:18
Page 26
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd
19/07/2007
17:18
Page 27
Download PDF
Similar pages