S-50 / S-55 Series - Tanning-Bed

1005378_S50_S55_Series_US_en_080130.qxd
30.01.2008
18:01 Uhr
Seite 1
S-50 / S-55 Series
Soltron, a Division of JK-Products & Services, Inc.
1 Walter Kratz Drive
Jonesboro, AR 72401
Phone: 800.643.0086 (Toll-free)
Fax: 870.935.3618
Website: www.soltron.us
1005378
E-Mail: sales@soltron.us
OPERATING INSTRUCTIONS
1005378-00- / us / kn / 03.2008
S-50 Turbo Plus VHP12
S-55 Turbo Plus VHP12
Identify your tanning device
For contact with Customer Services, please write down
the device number of your tanning device.
4
Global Service USA
A Div of JK Products & Services, Inc.
#1 Walter Kratz Drive
Jonesboro, AR 72401
800-445-0624
870-935-9046
e-mail: support@jkamerica.com
http://support.jkamerica.com
2
Skin types
For the recommended exposure schedule see page 4.
Skin type I (Sensitive):
Invariably gets sunburn, accepts little natural sunlight and does not tan.
Skin type II (Fair):
This is the individual that usually burns easily and severely, tans minimally or lightly and peels.
Skin type III (Average):
Often referred to as “Average” complexion, burns moderately and tans
about average.
Skin type IV (Brown):
This individual burns minimally, tans easily and above average with each
exposure.
Skin type V (Dark Brown):
This individual’s system rarely burns, tans easily and substantially.
3
Tanning times
Note:
Description of skin types see
Page 3.
“This product is in conformity with performance standards for sunlamp products under CFR21 Part 1040.”
4
Table of contents
7
General safety instructions and information
9
Description
19
Operation
22
Maintenance
47
Technical data / appendix
85
Index
96
5
Dear Customer,
The Soltron device you have purchased is a technically advanced and
powerful product. Your device was manufactured with the greatest care
and precision. It went through numerous quality and safety checks in order to guarantee trouble-free, safe operation. Nonetheless, you can also
make a significant contribution to your long-term satisfaction with your
device. Following the tips and instructions in the instruction manual will
ensure you enjoyment and pleasure with your device.
If you have any questions, we are always available to answer them.1)
Yours sincerely
JK-Products, Inc.
1) (800) 643 0086
6
• Please read and follow the instructions in this operating manual carefully. This will help prevent accidents and ensure that your sunbed is
always fully functional and operational.
• Always comply with generally accepted legal provisions and any further directives and statutory regulations, as well as any environmental protection requirements in force, including those of the country in
which the system is operated.
• Always comply with local regulations in force established by professional associations and other regulatory authorities.
Table of contents
Use the sunbed – but use it properly! . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Skin types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Tanning times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Important safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Instructions pertaining to a risk of fire, electric shock, or injury . . . . . . 10
Instructions pertaining to a risk of damage to the machine . . . . . . . . . 12
Product information acrylic glass panels . . . . . . . . . . . . . . 18
Meaning of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Obligations of the studio operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MP3 music (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Product information acrylic glass panels . . . . . . . . . . . . . . . . . . . . . . . 18
Environmental protection information . . . . . . . . . . . . . . . . . . . . . . . . . 18
Operation
Mandatory reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use the sunbed – but use it properly! . . . . . . . . . . . . . . . . . . . . .
Start of tanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt or end tanning session . . . . . . . . . . . . . . . . . . . . . . . . .
Regulating the facial tanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching air condition off and on . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulating body cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching AROMA on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching AQUA MIST on and off. . . . . . . . . . . . . . . . . . . . . . . . . . . .
MP3 player connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the audio system (channel). . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the volume and switching-off the audio systems . . . . . . . .
Running time of accent lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
23
25
25
26
27
28
31
33
35
37
39
41
44
46
Description
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7
Table of contents
Maintenance
Maintenance overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Cleaning and maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Relamping / maintenance instructions. . . . . . . . . . . . . . . . . . . . . . . . . 59
Cleaning/replacing UV low-pressure lamps in the sunbed base . . . . . 60
Cleaning/replacing UV low-pressure lamps in the canopy . . . . . . . . . 63
Cleaning/replacing interior lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Cleaning or replacing UV high-pressure lamps and filter panels
in the canopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Cleaning/replacing accent light in front panel . . . . . . . . . . . . . . . . . . . 72
Cleaning the base filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Air condition: Emptying the condensation tank and cleaning the filter. 76
Replacing the AROMA tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
AVS AROMA VITALIZER system: Replacing the canister. . . . . . . . . . 82
Technical data
Connected load, power and noise level. . . . . . . . . . . . . . . . . . . . . . . . 85
Rated power, activation and power levels of the UV lamps. . . . . . . . . 86
Installed lamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Spare parts and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Installation location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
8
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Customer information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Presettings – see “Presettings”, Order No. 1003844
Troubleshooting – see “Error codes”, Order No. 800641
Timer operation – see manual “Intellitan Remote Timer”,
Order no. 801129
Important safety notes
Safety notices
Description of warning signs
Danger notices, damage to persons:
Type and source of danger, e.g. “DANGER – High voltage!”
DANGER! Description of the consequences, e.g. “You can be killed or
injured by an electric shock!”
Countermeasures:
– Disconnect device from power supply before opening.
Caution notices, damage to property:
Caution!
The word “Caution” with this label points out that danger for
devices, materials and the environment can be expected
here.
Important information:
Note:
This symbol does not identify safety notices, but states information for a better understanding of the processes.
– Do not reach into the inside with the device switched on.
Warning notices, damage to persons:
Type and source of danger, e.g. “Warning – hot surface!”
WARNING! Description of the consequences, e.g. “You can burn your
hand (skin, face)!”
Countermeasures:
– Do not touch hot parts and nearby surfaces.
– Wait until hot parts and surfaces have cooled down.
9
Important safety notes
Instructions pertaining to a risk of fire, electric shock, or injury
DANGER – High voltage!
You can be killed or injured by an electric shock!
DANGER! Assembly and electrical connection must comply with national and local regulations.
– The device may only be assembled, installed, upgraded
or repaired by specially trained and instructed personnel.
WARNING – ultraviolet radiation!
Unprotected tanning may result in eye injury and eye disWARNING! eases.
The unprotected eye can become inflamed on the surface,
and in certain cases the retina can be damaged by excessive radiation. Cataracts can form after frequently repeated
exposure to radiation.
– Inform users to use the included protective goggles
that block UV (Order No. 84592-..).
WARNING – ultraviolet radiation! Follow instructions!
Failure to use protective eyewear may result in severe
WARNING! burns or other eye injury. If discomfort develops, discontinue use and consult a physician.
– A person who does not tan in the sun most likely will not
tan from the use of this device. Persons with very sensitive skins (skin type I) must not use the unit, as with this
skin type tanning is impossible without damaging the
skin (e.g. sunburn).
– Individuals with acute sunburn, individuals who have
had or have skin cancer, or individuals who are at increased risk of skin cancer, must not use the system.
– UV devices must not be used without taking medical advice if unexpected effects, such as itching, occur within
48 hours of the first session.
– The sunbed must never be used if a filter panel is missing or damaged, or the timer is defective!
– UV light from the sun or UV systems can cause injuries
to the skin or eyes. This biological effect is dependent
on the sensitivity of the individual's skin and on the type
and amount of UV light.
– As with natural sunlight, overexposure can cause eye
and skin injury, sunburn, and allergic reactions.
10
Important safety notes
– Repeated exposure may cause premature aging of the
skin and skin cancer.
– Medications or cosmetics applied to the skin, may inWARNING!
crease sensitivity to ultraviolet light.
– A person having a history of skin problems should consult a physician before use.
WARNING – risk of infection!
Infections can be transferred through skin contact.
WARNING! All items/equipment components, with which the user can
come into contact during tanning, must be disinfected after
every tanning session:
• Protective goggles
WARNING – ultraviolet radiation!
• Acrylic sunbed
Danger of long-term consequences.
• Handles and control panel
WARNING! – Overexposure should be avoided.
– The elderly should not use this equipment.
– Nursing infants and small children through age 7 years
may not use this device.
• MP3 cable
For fast, hygienic proper cleaning, use a specially developed fast disinfectant cleaner.
– The following applies to minors under the age of
18 years: Only use tanning devices in agreement with a
parent or guardian, or after consulting a physician.
– While there is no immediate clinical evidence of UVA exposure and its effects upon expectant mothers, it is
strongly advised that expectant mothers be discouraged
from using the tanning unit.
11
Important safety notes
Note:
Occasionally, persons using the tanning device will experience a slight reddening of the skin – usually in small patches – after the second or third session. This redness is often
accompanied by an itching sensation. This may be nothing
more than a heat “rash” caused by heat from the lamps
within the device. It is generally very limited and caused by
constant contact of the skin with the acrylic surface. It
should go away within approximately 24 hours and should
not reappear. This rashing can be lessened or prevented by
applying moisturizer lotion to the affected area after the tanning session is completed.
– Follow instructions.
– The time between the first two tanning sessions must be
at least 24 hours.
– Increasing tanning also requires an extension of the exposure time (= radiation time) or after a certain degree
of tanning has been achieved, a further intensification is
not possible. However, the radiation time may not be extended as desired within the scope of the permissible radiation doses! Therefore, only a certain degree of final
tanning dependent on the skin type can be achieved
without endangering your health.
– Inform users about proper tanning.
12
Instructions pertaining to a risk of damage to the
machine
CAUTION – danger of overheating!
Danger of overheating by obstruction of the air routing.
– Do not change, obstruct or block the air inflow and outflow area to the device or make any unauthorized
changes to the device. The manufacturer shall bear no
liability for damage or injuries resulting from such actions.
– Before putting a tanning device into operation, the transport pallet must be removed from under the device.
Danger of overheating by obstruction of the air routing.
Information for the studio operator
Meaning of symbols
Inform Customer Services
Filter panels
Soltron key
Cleaning and disinfectant agents
Do not touch, hot surface!
Part/item number (for orders)
Suction cup
Display of tanning time
Low-pressure lamp(s)
Display of run-on time (fan run-on)
UV low-pressure lamp(s)
Fault display (example),
see separate manual
Starter for low-pressure lamp(s)
Display of Music Channel 1 (Channel 1)
Factory setting: 1 channel
Customer service can set up to 7 channels
UV high-pressure lamp(s)
Display when adjusting volume
13
Information for the studio operator
e.g.
2s
0-3 min
14
Description
Caution, safety switch!
Accent lights
Two persons are required for this work step.
Body cooling with
AQUA SOLAR WITH SKIN+ ADDITIVE
Unscrew/release screw
Fragrance
(AVS AROMA VITALIZER system)
Tighten/lock screw
Press button
Cleaning
Press button for 2 seconds
Replacing
Duration: 3 minutes
Clean or replace depending on soiling
Loudspeaker
Draining
Headphone connection
Air condition
Information for the studio operator
Visual inspection
Filter/filter mat
Filter and filter mats must not be damp.
...
Continuation of work steps on next page
End of work step
15
Information for the studio operator
Intended use
Obligations of the studio operator
The tanning device is intended exclusively for cosmetic tanning of the human skin.
• As the operator you are responsible for informing users on possible
risks during tanning.
• The device is meant for commercial use only, not for home use.
• All danger and safety labels attached to the device must be observed!
Do not remove them!
• This device is used for tanning one adult person at a time.
• The user wears suitable eye protection that blocks UV radiation during tanning.
Any other use shall be considered improper. The manufacturer cannot be
held liable for damage or injuries resulting from this. The operator bears
the sole risk for this.
The proper use also includes compliance with the manufacturer’s instructions, operating and maintenance conditions. This device may only be
operated, maintained and repaired by persons familiar with these tasks
and who have been informed of the dangers involved.
• No safety equipment (e.g. panel switch) may be removed or deactivated which can impair the safe operation of the device!
• The device may only be operated in a serviceable condition!
• The operator is bound to ensure that the equipment is handled correctly.
Guidelines
This device was built conforming to UL STD 482, and is certified to CAN/
CSA STD C22.2 2 No. 224.
Export
We would like to point out that these devices are exclusively intended for
use in the USA and Canada and may not be exported to other countries
and operated there! The manufacturer assumes no liability whatsoever
in the event of non-compliance! We explicitly emphasize that high liability
risks may occur for the exporter and/or the operator in the event of noncompliance.
16
Information for the studio operator
MP3 music (optional)
The personal use of an MP3 player during tanning is not a public broadcast in copyright terms, so that there is no obligation for registration or
payment by the studio owner to the corresponding copyright owning
company in respect of copyright exists on the part of the studio operator.
for each audio CD, MC, audio DVD etc. for which you have obtained the
legal rights. The original sound storage medium must be stored and is
not allowed to be used at the same time.
The same regulations apply for the official use of MP3 music files as for
other music sources: As studio owner you are only allowed to use original
audio CDs, MCs, audio DVDs etc. in your premises and / or play them in
the MP3 music module fitted to the Soltron professional sunbed if you
have already obtained the corresponding performing rights.1)
Copy-protected audio CDs, MCs, audio DVDs etc., as well as the tracks
included on these media, are not allowed to be converted to MP3 format
and / or stored on hard discs, audio CDs, MCs, audio DVDs etc. when
software and / or computer programs are used for this purpose which
cancel or avoid the copy-protection included on the storage media.
At the request of the external staff or any other controlling body of the
responsible company, you must always be in a position to prove that you
have purchased the performance rights by showing the relevant
authorisation.
As long you follow the advice given above and have gained of the necessary rights, you may convert your original audio CDs, MCs, audio
DVDs etc. to the MP3 format required for the player. However, you may
only create one copy (either a duplicate or a conversion to MP3 format)
1) from the company responsible for the allocation of commercial performing
rights in your country (in Germany: GEMA/GVL)
17
Information for the studio operator
Product information acrylic glass panels
The acrylic glass panels for the tanning devices are produced of acrylic
glass developed especially for this application. The acrylics used are
characterized by a particularly high UV permeability and resistance, as
well as an easy-care, hygienic surface that is gentle to the skin.
The acrylic glass panels are formed to their shapes for the specific devices in a technically complex production process. Despite state-of-the-art
production know-how, the presence of minor spots, air bubbles or
streaks in the acrylic panels is unavoidable. In addition, microfine hairline
cracks can occur on the bed surface during operation.
These occurrences are material-dependent and are unavoidable in
processing, however have no significant effect on the use or value and
can therefore not be recognized as defects.
CAUTION!
Cosmetics or sun screen products must be removed prior to
using the sunbed as they can cause damage (e.g. fine
cracks on the surface) when used continuously.
Environmental protection information
Environmental Declaration – The JK Corporate Group
The JK corporate group is subject to the strict regulations of EC Directive
761/2001 and the ISO 14001 standard, and undergoes regular internal
and external environment audits performed by trained auditors.
Environmental regulations – disposal of lamps
UV low-pressure lamps and UV high-pressure lamps contain fluorescent
materials and other waste containing mercury.
According to the national waste disposal laws and in accordance with the
municipal waste regulations, proof must be provided of the proper disposal of UV lamps.
Your local environmental agency will be happy to assist you with the disposal of UV lamps.
Packaging
All packaging consists of 100 % recyclable materials.
Disposal of recyclable materials
The device has been produced of recyclable materials. When being
scrapped later, the device must be disposed of properly. Soltron, Inc. will
provide you with information on the content or potential hazards of the
materials used.
18
Equipment
Depending on the model, each device is equipped differently.
This instruction manual covers all standard and optional components/
functions to be taken into consideration during operation and/or maintenance.
The control panel also differs according to the various equipment: the
only visible buttons are those that can be operated, i.e. the corresponding function must be part of the device’s equipment.
19
Description
1. Facial tanner (UV high pressure lamps)
2. UV low pressure lamps, base
3. Partition
4. Acrylic cover, base
5. Infrared interface
6. UV low pressure lamps, canopy
7. Interior lighting
8. Body cooling air nozzles
9. VITALIZER nozzle
10. Face cooling air nozzles/AROMA
11. Control panel
12. Accent lights, canopy
13. Accent light, front panel
20
Accessories
14. Central air discharge socket
15. Audio-system, 2 loudspeakers
15.1. Headphone connection
15.2. MP3-connection
Some accessory parts are taken into account in the
maintenance schedule beginning on page 54 and in
the spare parts section from page 89. However this
does not automatically mean that your device is fitted
with this equipment.
Order numbers and more accessories are listed in
the sales documentation and the planning manual.
21
Operation
Mandatory reading
Always read and follow all instructions for proper usage prior to allow
anybody using a tanning device. The operating instructions included with
this device must always be followed to prevent possible injuries or to reduce them to a minimum.
Inform users
• to use provided UV-blocking protective eyewear whenever the equipment is energized.
• to follow the exposure schedule in accordance with their skin type.
Failure to do so may result in overexposure.
A tanning system is not a toy. You cannot vary the strength of the lamps
in your unit.
Should you have any questions regarding the proper use of your tanning
system, contact Global Service USA at:
800 445 0624
7:00 a.m. to 7:00 p.m. (CT)
Warning – ultraviolet radiation!
Danger of skin injuries and skin diseases!
• The sunbed must never be used when a filter panel is
WARNING! missing or damaged, or the timer is defective!
22
Note:
When describing the operation, the tanning device is often
shown with the canopy open. During tanning the canopy
must always be closed.
Proper operation is not possible with the canopy open.
Operation overview
...
23
Operation overview
24
see separate instructions “Presettings”, Order no. 1003844
Tanning
Use the sunbed – but use it properly!
A few things need to be noted to get maximum enjoyment from a sunbed.
Here are some answers to some frequently asked questions.
Make-up on the sunbed?
Please remove make-up or don't use make-up while tanning. Clean skin
absorbs UV light better.
A wide variety of ingredients are found in cosmetics. Again, whether
these are emulsifiers, greases, or so-called scents – in conjunction with
UV radiation, these can cause allergic reactions of the skin.
Accordingly, a must before using a sunbed is: Remove all make-up. This
is essential. Make-up clogs the pores in the face. The UV light from a
sunbed re-opens these clogged pores so that not only does the light penetrate the skin, but also the allergenic components of the make-up.
A further negative consequence of make-up is that the appearance of the
skin deteriorates irreversibly over a period of time. However good a decent make-up might be – in conjunction with UV light, it causes more
harm than good. Therefore: Remove all make-up before a session on
your sunbed – it will be much better applied afterwards.
Are medications and the sunbed compatible?
It is known that some medications increase the skin's sensitivity to UV
light. This probability is particularly high with antibiotics, sulphonamides,
psychiatric drugs, tranquillizers, anti-diabetes treatments and diuretics.
Sun creams which contain psorale or kumarin also increase skin sensitivity. If you are in any doubt, first ask your doctor - then you can enjoy
the sun at no risk.
Contact lenses on the sunbed?
The answer is: Yes! Like any other sunbed user, contact lens wearers
should also wear special protective goggles which protect the eyes
against UV radiation. To guarantee better protection, wearers of spectacles and contact lenses can ask their optician for exchange contact lenses with UV protection. The UV-A and UV-B filters built into exchange
contact lenses will protect the cornea and the internal parts of the eye
against almost 100% of the energy in UV radiation.
This will benefit sunbed users not only in the open air, but on the sunbed
itself. For more information, ask your optician or optometrist.
Showering after leaving the sunbed?
The browning is in the skin, not on it. Therefore you cannot wash it off.
Treat your skin to a moisturizing cream after showering.
...
25
Use the sunbed – but use it properly!
Start of tanning
Closing the canopy
The device is started automatically with an internal or external timer.
Note:
Timer instructions: see separate manual1).
Preparation time
Before the UV lamps turn on, you have a few minutes to prepare yourself.
During the preparation time you can switch on the UV lamps at any time
by pressing the START/STOP button.
– Remove your clothes and all jewelry.
– Remove make-up and other cosmetics.
– Remove glasses. Contact lenses can be worn under the protective
goggles.
– Put on the protective goggles.
– Lie down on the bed surface.
– Close the canopy.
– Press the START/STOP button.
1) Order no 801129-..
26
...
Use the sunbed – but use it properly!
Interrupt or end tanning session
Settings on start-up
The tanning session ends automatically after the preset time has run
down. The internal fan continues to run for approx. three (3) minutes to
sufficiently cool the device.
– To interrupt a tanning session, press button START/STOP anytime
during a session.
– Press START/STOP again to restart the lamps.
optional:
27
Regulating the facial tanner
Switching the facial tanners OFF:
– Press button
for two (2) seconds.
Switching the facial tanners on again:
– Press button
. It takes approx. one (1) minute until the facial tanners reach their full output.
Adjusting the intensity:
– Press button
.
– While the button
the facial tanners.
flashes, press + or – to adjust the intensity of
1
...
28
Regulating the facial tanner
2
STOP
3
...
29
Regulating the facial tanner
START
4
30
Switching air condition off and on
Switching air condition OFF:
– Press button
for 2 seconds.
Switching air condition on again:
– Press button
again. It takes approx. 3 minutes until the cooling
effect of the air condition is reestablished.
STOP
1
...
31
Switching air condition off and on
START
2
32
Regulating body cooling
– Press button
.
– While the button flashes, press the plus or minus button to change the
intensity of the air stream.
1
...
33
Regulating body cooling
2
34
Switching AROMA on and off
Switching AROMA on:
– Press button
.
Switching AROMA OFF:
– Press button
again.
START
1
...
35
Switching AROMA on and off
STOP
2
36
Switching AQUA MIST on and off
Switching VITALIZER on:
– Press button
.
Switching VITALIZER OFF:
– Press button
again.
START
1
...
37
Switching AQUA MIST on and off
STOP
2
38
MP3 player connection
MP3 player connection
Studio customers can connect their own MP3 player to the device when
the “Audio System” accessory is available.
1
2
c
Jack plug (Mat.-Nr. 1001855-..) provided for use by the studio operator (1.5 m / 2 x 3.5 mm stereo jack plug).
d
MP3 player connection: refer to the manufacturer’s documentation.
Loud music might disturb other studio users!
...
– Use headphones whenever necessary.
39
MP3 player connection
Caution!
The heat might damage your MP3 player.
– Do not position the unit so that it receives direct tanning radiation.
Cable may be torn off, connectors may be damaged.
– Do not pull on cable when unplugging MP3 player.
40
3
Selecting the audio system (channel)
I.CH (internal): SD card “music”
E.CH (external): externally connected systems (e.g. CD-player)
P.3: MP3 player
1
...
41
Selecting the audio system (channel)
2
Choosing a track (internal/external)
3
...
42
Selecting the audio system (channel)
4
43
Adjusting the volume and switching-off the audio systems
Risk of hearing loss!
– With time, the human ear becomes accustomed to high
sound levels.
– The higher you adjust the volume, the quicker the hearing
can be damaged.
– The use of ear pieces and headphones at high volume can
lead to permanent hearing loss.
Maximum
1
...
44
Adjusting the volume and switching-off the audio systems
Minimum
2
OFF
3
45
Running time of accent lights
The accent lights are automatically switched
on at the end of the tanning session after the
set operating time and are switched off again at
the beginning of the next tannings session.
Stand-by
1
The running time of the accent lights in the
Standby mode can be changed with the presettings – see separate instructions.
2
See separate instructions “Presettings”, Order no. 1003844
46
Safety information for maintenance and care
DANGER!
Extreme danger! High voltage!
CAUTION!
During maintenance work there is a risk of touching live
parts and receiving a fatal electric shock.
Only use genuine spare parts of the same type!
The use of other parts may limit or void your manufacturer’s
warranty!
Any liability is excluded in case of damage or injury proven
to be the result of the use of non-genuine spare parts.
– Disconnect device from power supply before opening –
also see Page 48.
– Do not reach behind covers and do not open the device
with the device switched on.
– Refit any safety devices (e.g. switches) after the work
has been completed.
Maintenance and care play a major role in deciding whether the device
meets the requirements placed on it in a satisfactory manner. The compliance with the specified maintenance intervals and the careful conducting of the maintenance and care work are therefore absolutely necessary
– see Page 54.
The current operating hours of the parts requiring maintenance can be
displayed in the Presetting mode – see separate instructions “Presettings”, Order no. 1003844.
Fire hazard!
High-pressure lamps that have not been approved by Soltron can explode. Hot lamp components can set other
components on fire. People can be killed or severely injured due to smoke inhalation and fire.
– Only fit high-pressure lamps recommended by Soltron.
– Clean the inside of the tanning device regularly. Dustparticles are combustible!
Danger of burns!
DANGER!
Only use the specified genuine UV lamps and filter panels!
Using other UV lamps leads to modified radiation. This
could potentially result in severe burns to the user!
The use of other UV lamps and filter panels invalidates CE
conformity and the GS approval mark!
...
47
Safety information for maintenance and care
Power Off device and secure against being switched on again
A prohibition sign with the text:
“Work in progress!”
Extreme danger!
If work is to be performed on the devices,
they must be powered off. That means that
DANGER!
all live lines must be switched off.
Switching off the device alone is insufficient,
as certain points may remain energized.
Therefore, switch off and lockout circuit
breakers before performing any work.
• “Place: ..............................”
• “Sign may only be removed by: ............”
must always be securely mounted immediately.
01511 / 1
Extreme danger!
04049 / 0
DANGER!
Prohibition signs must not be hung on or touch live parts.
Extreme danger!
Severe accidents can occur if the device is mistakenly
switched on again.
DANGER!
Immediately after powering off, secure all switches or fuses
used for power against being switched on again.
• A strip of adhesive tape with the wording
"DANGER do not switch ON!" may be applied
over the actuation levers of circuit breakers
which cannot be removed.
01510 / 1
...
48
Safety information for maintenance and care
Malfunctions
The display shows error codes1) to make it easier to localize the cause
of the problem.
• If a malfunction occurs, the error code flashes in the display.
• If several malfunctions occur, the error messages are displayed alternately.
• The fault remedy is acknowledged by holding down the START/
STOP button.
• If the problem cannot be remedied, inform Customer Service – see
Page 2.
1) See separate instructions “Error Codes”, Order no. 800641
49
Maintenance overview
see separate instructions “Presettings”, Order no. 1003844
50
Cleaning
Acrylic glass surfaces
CAUTION!
Do not rub with a dry cloth – danger of scratching!
For fast, hygienic proper cleaning of acrylic glass surfaces,
use a specially developed fast disinfectant cleaner.
Other cleaning agents, especially concentrated disinfectants or solvents (e.g. Lysoform, ethyl alcohol or other liquids containing alcohol) must never be used for cleaning.
Failure to observe this voids all warranty claims.
Plastic surfaces
For cleaning the other plastic surfaces, it is best to use warm water and
a leather cloth. Never use aggressive cleaning agents containing alcohol
or essential oils. These may lead, in the long run, to damage not covered
by the warranty.
During cleaning, a slight discoloration of the leather cloth by the rubber
seals must be expected for production-related reasons.
Note:
Prevent damage to plastic surfaces. Remove rings, watches, bracelets etc. before the start of cleaning work.
02756 / 0
...
51
Cleaning
Filter and filter mats
Filters in the sunbed base, in the air conditioner
Dry cleaning: vacuum cleaner (depending on the
degree of soiling)
Moist cleaning: water and detergent, or dishwasher.
Air intake openings in the canopy
Dry cleaning: vacuum cleaner
Moist cleaning: water and a mild detergent.
Caution! The system can be damaged by moisture!
The cleaned filters must be dry when re-assembling.
Cleaning filter panes and lamps
The UV high-pressure lamps fitted are broadband radiators which can be
operated at different outputs (approx. 240-520 W).
UV low pressure lamps: Clean with water only (damp
cloth)
UV high pressure lamps: Clean jackets with methylated
spirits if necessary.
Filter panes: Clean with water only (damp cloth)
Caution! Risk of damage to the device!
Regularly check the filter grille, filter and cooling fins
on the air conditioning system and clean as necessary
– see Page 76.
For cleaning the cooling fins we recommend using our
special fin comb, Order No. 15720470.
52
Maintenance
VITALIZEr
Acrylic covers
The VITALIZER function sprays a fine mist of AQUA SOLAR WITH
SKIN+ ADDITIVE into the tanning chamber.
The acrylic covers for the sunbeds are produced of acrylic glass
developed especially for this application. The acrylics used are
characterized by a particularly high UV permeability and resistance, as
well as an easy-care, hygienic surface that is gentle to the skin.
Health hazard for your customers!
Water contaminated with bacteria can cause skin rashes and
other allergic reactions in sunbed users.
– Do not, therefore, fill the VITALIZER canister with tap water or other liquids.
– Only replace the VITALIZER canister with a genuine canister.
– Do not add any leftovers from the old canister to the new
canister.
– Ensure that the specified maximum temperature is not exceeded during transport and storage.
– Note the expiry date on the canister.
The acrylic covers are formed to sunbed-specific shapes in a technically
complex production process. Despite state-of-the-art production knowhow, the presence of minor spots, air bubbles or streaks in the acrylic
panels is unavoidable. In addition, hairline cracks can occur on the
acrylic glass panel during operation.
These occurrences are material-dependent and are unavoidable in
processing, however have no significant effect on the utility value and
can therefore not be recognized as defects.
Caution!
Cosmetics or sun screen products must be removed prior to
tanning as they can cause damage (e.g. fine cracks on the
surface) when used continuously.
AROMA
The AVS AROMA VITALIZER system also includes fragrances, which
are distributed via the head nozzles.
The aroma “Cabin” is distributed in the cabin.
Note:
Alternatively further fragrances are available. More
information is available from JK-Licht GmbH.
53
Cleaning and maintenance intervals
After each tanning

☞ 51
Schmerler 2255
Soltron 84592


☞ 51
☞ 51

1001855

☞ 51
☞ 51
Confirm cleaning by pressing the START/STOP button (when the follow-up
time of the fan in the device has finished).
Intervals
Intervals, see
“PRODUCT INFORMATION
AQUA SYSTEM”
(order no.: ▲ 801610-..).
54
...
Cleaning and maintenance intervals
–
☞ 51

☞ 82
Empty

☞ 76
Air intake openings
Fire hazard!
Fluff is inflammable! Regularly remove fluff in
the air intake area.
– Use a vacuum cleaner to prevent fluff
getting inside the unit.
...
55
Cleaning and maintenance intervals
50 h

☞ 74

☞ 76

☞ 76
300 h

a)
b)
☞ 80
...
56
Cleaning and maintenance intervals
500 h
a)
☞ 69
b)
☞ 60
c)
☞ 63
1000 h
b) c)
☞ 60, 63
f) g)
☞ 72,
66
...
57
Cleaning and maintenance intervals
1500 h

3000 h

a)
58
☞ 69
Relamping / maintenance instructions
It is imperative that you, the owner and/or operator, check all components for any signs of wear which may occur through normal use.
Observe the cleaning and maintenance schedule specified in the maintenance table on Page 54 to 58.
Only replace UV low-pressure lamps with the original lamp type or with
compatible lamps.
Only replace UV high-pressure lamps with the original lamp type or with
compatible lamps.
– Before replacing lamps or other spare parts, wait until
lamps and metal parts of the device have cooled down
sufficiently.
Danger of pinching!
When opening and closing the tray, panels and covers, you
can pinch your fingers.
Should you require any assistance or need additional information, please
call Global Service USA at 800 445 0624, Monday through Friday
7:00 a.m. - 7:00 p.m. CT, Saturday 8:00 a.m. to 3:00 p.m.
CAUTION – Damage due to improper maintenance!
Improper maintenance can cause the device to be damaged or to become unusable.
– Always comply with the specified maintenance intervals.
– Follow the cleaning instructions.
– If the maintenance intervals for the UV lamps are exceeded or incompatible UV lamps are installed, the share of harmful UVB radiation
may increase. Sunburn and other skin damage may result.
WARNING!
Danger of burns from hot lamps and device parts!
If the tanning device was operated before being switched
WARNING! off and opened, lamps and housing parts may be hot.
59
Cleaning/replacing UV low-pressure lamps in the sunbed base
2
4
3
5
Power Off!
1
...
60
Cleaning/replacing UV low-pressure lamps in the sunbed base
6
8
Attention!
Soiling on the panes is burned in by
the hot lamps and results in the long
term in unserviceable panes.
– Remove fingerprints and other
soiling carefully.
7
1
9
2
03108 / 0
...
03099 / 0
61
Cleaning/replacing UV low-pressure lamps in the sunbed base
Close:
10
11
62
12
Cleaning/replacing UV low-pressure lamps in the canopy
Caution!
2
Canopy panel may break if allowed to fall or if pressure is exerted on the reverse side of an open
canopy. Such failure is not covered by manufacturer's warranty.
Danger of injury from the
canopy panel!
The canopy panel is heavy and
WARNING! falls down by itself after unscrewing the 3 screws.
Power Off!
1
3
– Support canopy panel.
– Loosen screws in the specified order.
...
63
Cleaning/replacing UV low-pressure lamps in the canopy
4
5
6
1
7
2
03108 / 0
64
8
Attention!
– Do not pinch or kink the cable –
see Fig. 9!
03099 / 0
...
Cleaning/replacing UV low-pressure lamps in the canopy
9
Close:
10
65
Cleaning/replacing interior lighting
Caution!
2
Canopy panel may break if allowed to fall or if pressure is exerted on the reverse side of an open
canopy. Such failure is not covered by manufacturer's warranty.
Danger of injury from the
canopy panel!
The canopy panel is heavy and
WARNING! falls down by itself after unscrewing the 3 screws.
Power Off!
1
3
– Support canopy panel.
– Loosen screws in the specified order.
...
66
Cleaning/replacing interior lighting
4
6
8
1
2
03350 / 0
5
03099 / 0
7
...
67
Cleaning/replacing interior lighting
9
Close:
10
68
Cleaning or replacing UV high-pressure lamps and filter panels in the canopy
Caution!
2
Canopy panel may break if allowed to fall or if pressure is exerted on the reverse side of an open
canopy. Such failure is not covered by manufacturer's warranty.
Danger of injury from the
canopy panel!
The canopy panel is heavy and
WARNING! falls down by itself after unscrewing the 3 screws.
Power Off!
1
3
– Support canopy panel.
– Loosen screws in the specified order.
05097 / 0
69
...
Cleaning or replacing UV high-pressure lamps and filter panels in the canopy
4
6
8
3
1
2
05098 / 0
5
05101 / 0
7
9
2
05099 / 0
70
1
05102 / 0
...
Cleaning or replacing UV high-pressure lamps and filter panels in the canopy
10
12
03699 / 0
05104 / 0
Close:
11
13
1
2
3
05103 / 0
71
Cleaning/replacing accent light in front panel
2
4
07162 / 0
07165 / 0
Power Off!
1
3
...
72
Cleaning/replacing accent light in front panel
5
6
07166 / 0
73
Cleaning the base filters
2
4
07759 / 0
Power Off!
1
3
5
...
74
Cleaning the base filters
6
Close:
7
75
Air condition: Emptying the condensation tank and cleaning the filter
Power Off!
1
3
2
4
...
76
Air condition: Emptying the condensation tank and cleaning the filter
5
7
9
6
8
10
...
77
Air condition: Emptying the condensation tank and cleaning the filter
11
13
15
03319 / 0
12
14
...
78
Air condition: Emptying the condensation tank and cleaning the filter
16
Close:
17
79
Replacing the AROMA tank
18
2
2
1
1
03246 / 0
Power Off!
1
19
3
2
2
1
1
BIS
AR RE
LTB EFO
HAST B
BE 007
02
/2
N
DO
NE
OPE
80
03354 / 2
...
Replacing the AROMA tank
4
20
BIS
AR RE
LTB EFO
HAST B
BE 007
02
/2
N
O
NED
3/2
08/0
OPE
06488 / 0
Close:
5
21
2
1
2
03355 / 0
81
AVS AROMA VITALIZER system: Replacing the canister
22
2
23
3
Power Off!
1
...
82
AVS AROMA VITALIZER system: Replacing the canister
24
26
Note:
After replacing the canister, the
system must be vented. To do this
change to service mode and select
function 231 (see separate
instructions “Presettings”, Order
number 1003844).
Close:
25
27
...
83
AVS AROMA VITALIZER system: Replacing the canister
28
29
84
Connected load, power and noise level
Model:
Rated power consumption
without air condtion:
with air condition:
S-50
Turbo Plus
S-55
Turbo Plus
9,400 W
10,400 W
–
11,500 W
Rated frequency:
60 Hz
Rated voltage:
230 V
Fuse rating:
Powerinput 3-pole
(max. 50 amp)
230V AC 60 Hz
Powerinput 1-pole
(max. 90 amp)
230V AC 60 Hz
40 amp 3-pole or
80 amp 2-pole
Conformity mark:
Noise level at 1 m from
the sunbed:
Noise
level in
sunbed:
68.1 dB(A)
66.4 dB(A)
04045 / 1
<81 dB(A)
85
Rated power, activation and power levels of the UV lamps
Rated power
Activation / power levels
a)
400 W
400 W / 240 W / 120 W
b)
180 W
180 W
c)
160 W
160 W
a)
400 W
400 W / 240 W / 120 W
b)
180 W
180 W
c)
160 W
160 W
S-50 Turbo Plus
S-55 Turbo Plus
86
Installed lamps
UV lamps, starters, filter panels
Order No. and lamp name
S-50 Turbo Plus
S-55Turbo Plus
Low pressure lamps
c) 1005341-..
22
26
16
16
38
42
a) F100723-.. JK Ergoline 400 W
3
4
a) 1005413-..
3
4
Soltron VHP12 160 W
b) 1005339-..
Soltron VHP12 180 W
Starter
10002-.. Starter S12 (b, c)
High pressure lamps and filter panels
87
Installed lamps
Accent lights
Design Peach Party / Design Queen Berry
Standard lamps
d)
1x
blue
36 W
▲ 11792-..
e)
1x
white
58 W
▲ 1002108-..
1x
Makrolon tube pink
1x
white
1x
Makrolon tube magenta
3x
S10
f)
▲ 1002101-..
36 W
▲ 1002106-..
▲ 1002107-..
Starter
d) e) f)
88
▲10047-..
Spare parts and accessories
Filter, VITALIZER, AROMA
Acrylic glass, fan

4x
52104-..
 1x
1004424-..

1x
–
 1x
1501870-..

1x
51937-..
 1x
Soltron
84592-..
Schmerler
2255

VITALIZER, 6000 ml
1x

3651803-..
or
 1x
1001855-..
AROMA, 100ml
a) Energy
b) Cabin
a)
b)
3651603-..
3651503-..
89
Dimensions
max. 300 lb/135 kg
A=
B=
C=
C1 =
D=
E=
E1 =
F=
TK =
BK =
90
66 15/16 in
51 3/4 in
56 13/16 in
56 1/8 in
88 9/16 in
89 3/8 in
93 5/16 in
32 11/16 in
82 11/16 in
94 1/2 in
1,700 mm
1,315 mm
1,443 mm
1,425 mm
2,250 mm
2,270 mm
2,370 mm
830 mm
2,100 mm
2,400 mm
Installation location
Ventilation
Attention! Danger of failure!
Non-observance of the ventilation information can lead to serious system
malfunctions.
Information on air supply and extraction planning can be obtained from the customer service (see Page 2).
Operating altitude
For altitudes greater than 2000 m above sea
level a conversion must be carried out to ensure trouble-free operation. Please contact Customer Service (see Page 2) before carrying out
the conversion and starting up the unit for the
first time.
91
JK-Products, Inc. – Limited Warranty
JK-Products, Inc. warrants its products to be free from defects in materials and workmanship under intended normal use as described in the
unit's Operation and Instruction Manual, for a period of three (3) years
from date of sale.
This Limited Warranty applies only to the original purchaser of the equipment through JK-Products, Inc. or its authorized dealer or distributor, and
is not transferable.
Global Service USA obligations under this warranty are limited to repair
or replacement of any defective part without charge for that part to the
original purchaser, with the following exceptions:
A Fluorescent lamps are warranted against defects for a period of thirty
(30) days from date of sale.
B Only parts obtained through JK-Products, Inc., its authorized dealers
or distributors may be used. Transportation costs for parts shipped to
the consumer and the return of defective parts to Global Service USA
are not included.
C Labor will be furnished without charge for ninety (90) days from date
of purchase only. All labor and related charges must be authorized by
Global Service USA prior to start of repairs, and must coincide with
Global Service USA established rates and time allotment policy.
D Acrylic: Refer to Manufacturer's Acrylic Warranty Policy.
It is imperative that the original customer completes and returns the enclosed warranty card within 10 days after purchase to insure valid registration and coverage for potential claims.
If the warranty card is not registered, proof of purchase from JK-Products, Inc. or its authorized dealer or distributor will be required prior to any
consideration on warranty claims. This could result in service delays.
92
This warranty is extended to the individual or legal entity, whose name
appears on the warranty registration card filed with Global Service USA,
or whose name appears on the original sale document and may not be
transferred to any other individual or legal entity.
This warranty does not apply to any failure of the product, or any parts of
the product due to alterations, modifications, misuse, abuse, accident,
improper maintenance, improper installation, acts of God or if the serial
number on the product has been removed, altered or defaced. Adequate
packaging must be used for returned goods to prevent freight damage.
There are no warranties which extend beyond the description on
the face hereof. There is no express or implied warranty of fitness
of merchantability.
The remedies provided in this limited warranty are the exclusive remedies provided to the purchaser by Global Service USA and are
provided in substitution of all other remedies. Consequential and
incidental damages are excluded.
No person, firm or corporation is authorized to obligate JK-Products, Inc.
for any liability in connection with the sale or use of these goods.
JK-Products, Inc. – Limited Warranty
Limited Acrylic Warranty
JK Products, Inc. warrants its acrylic sheets to be free from defects in material and workmanship, under intended normal use, for a period of one
(1) year from date of sale of the tanning bed. Due to the tanning lotions,
cosmetics, disinfectant and improper cleaners used on tanning surfaces
that cannot be controlled by JK Products, Inc., after the first thirty (30)
days of warranty period acrylic will be subject to a prorated cost to the
consumer.
JK Products, Inc. obligations do not include transportation charges on replacement acrylic.
JK Products, Inc. assumes no liability for the cost of removing defective
sheets or installing replacement sheets, nor for damage to persons or
property.
To make a claim, contact an authorized dealer or distributor of JK-Products, Inc. or Global Service USA with the model number, the serial number, and the date of purchase of the bed in which the acrylic will be used.
There are no warranties which extend beyond the description on
the face hereof. There is no express or implied warranty of fitness
or merchantability.
The remedies provided in this limited warranty are the exclusive remedies provided to the purchaser by Global Service USA and are
provided in substitution of all other remedies. Consequential and
incidental damages are excluded.
Global Service USA
A Div of JK Products & Services, Inc.
#1 Walter Kratz Drive
Jonesboro, AR 72401
800-445-0624
870-935-9046
e-mail: support@jkamerica.com
http://support.jkamerica.com
93
JK-Products, Inc. – Limited Warranty
Warranty Claims
Each dealer/distributor has their own internal procedure for handling
Warranty Claims and credits.
Policy & Procedures
NOTE:
1. When to file a Warranty Claim:
In the event that your tanning system is not functioning properly under intended normal use as described in the unit's Operation an Instruction
Manual, you may then have established cause to file a Warranty Claim.
JK-Products, Inc., the manufacturer, does not involve itself
in the direct handling of a Warranty Claim except where mitigating circumstances apply and where required by law.
NOTE:
Both the tanning system and legal registered owner must
meet the criteria established under JK Products, Inc. Limited Warranty as described in this manual before any Warranty Claim will be considered.
2. Where to call to place a Warranty Claim:
JK-Products, Inc. is supported nationwide by an extensive dealer/distributor network through whom the majority of our units are sold. These dealers/distributors are required by contract to stock sufficient parts to meet
the various warranty and nonwarranty needs of their customers.
Therefore, in order for you to properly file a Warranty Claim, you must locate the name and phone number of the dealer/distributor through whom
you purchased your unit. Normally this information can be easily located
either on your paid invoice or other proof of purchase documentation that
you received when taking delivery of the unit.
Next, notify the dealer/distributor of the serial number, model number and
date unit was purchased. This will initiate the Warranty Claim process.
Upon determination of the problem, your dealer/distributor can then supply you with the part(s) and proper instructions to return your unit to working order.
94
NOTE:
If part returned to Global Service USA proves to be operational and not defective, or if product code numbers on part
do not correspond with individual unit date on file with Global Service USA, then a 30% restocking fee will be charged
in addition to the retail purchase price of part.
Acknowledgment of the Agreement is not required for acceptance of the
foregoing stipulations.
Labor Warranty Claim/Credit Procedures
Global Service USA furnishes labor without charge for a period of 90
days from date of purchase. All labor and related charges must be authorized by Global Service USA prior to start or repairs, and must coincide
with Global Service USA established rates and time allotment policy.
Please contact our Service Department for authorization and billing procedures.
JK-Products, Inc. – Limited Warranty
Limited Lifetime Warranty
Global Service USA warrants specific individual components of the tanning system against defects in materials and workmanship for the life of
the product. Coverage is limited to units purchased after November 1,
1994.
This warranty is restricted by the following components only:
• Steel Back Panels
• Structural Steel Frame Components
• Exterior Steel Body.
NOTE:
Components are warranted on an individual basis and not
as they may effect the complete product.
Warranty coverage does not include cosmetic abnormalities such as
scratches, nicks, dents, rust, oxidation of paint or other cosmetic changes that do not interfere with the designed function of the unit.
This warranty does not include failure of the product due to alteration,
modifications, misuse, abuse, improper maintenance, improper installation or repair.
This warranty is not transferable and is only applicable to the original purchaser named on a completed and registered warranty record at JKProducts, Inc. headquarters.
JK Products, Inc. obligations do not include transportation charged on
the shipping of new components to the customer or on the return of defective components of the manufacturer. All freight charges must be paid
by the customer.
There are no warranties which extend beyond the description on the face
hereof. There is no express or implied warranty of fitness or merchantability.
The remedies provided in this limited warranty are the exclusive remedies provided to the purchaser by Global Service USA and are provided
in substitution of all other remedies. Consequential and incidental damages are excluded.
NOTE:
Any misuse, abuse, modification, alteration, improper maintenance, improper installation, etc. of this product or its intended use will subject said party to direct responsibility and
liabilities for any and all consequences resulting from such
action. Furthermore, such actions will void all warranties
and may relieve Global Service USA of any liabilities relating to said product.
95
Index
A
Accent lighting, maintenance...................... 72
Accent lights ............................................... 88
Accessories ................................................ 21
Acrylic glass panel
Allowable loading ............................... 90
Product information............................ 53
Acrylic glass, cleaning ................................ 51
Air condition
Cleaning the filters ............................. 76
Operation ........................................... 31
Allergies ...................................................... 25
AROMA tank, replacing .............................. 80
AVS AROMA VITALIZER system......... 53, 89
B
Base filter, maintenance ............................. 74
Base, replacing the UV lamps .................... 60
Body cooling ............................................... 33
C
Canopy, interior lighting .............................. 66
Canopy, replacing the UV lamps ................ 63
Care ............................................................ 47
Channel ...................................................... 41
Cleaning...................................................... 51
Filter ................................................... 52
Lamps, filter panels............................ 52
Cleaning intervals ....................................... 54
96
Connected load........................................... 85
Contact lenses ............................................ 25
Control elements ......................................... 23
D
Description .................................................. 20
Dimensions ................................................. 90
Disinfection.................................................. 51
Disposal of lamps........................................ 18
E
Empty the condensation tank...................... 76
Ending tanning session............................... 27
Environmental protection ............................ 18
Equipment................................................... 19
Extraction planning...................................... 91
F
Facial tanner
Operation............................................ 28
Replacing high pressure lamps .......... 69
Filter panels................................................. 87
Filter panels, maintenance .......................... 69
Filter, cleaning intervals .............................. 56
Fin comb ..................................................... 52
G
Glasses ....................................................... 25
Global Service USA, address........................ 2
Guidelines ................................................... 16
I
Installation location......................................91
Installed lamps ............................................87
Intended use................................................16
Interior lighting, maintenance ......................66
Interrupting tanning session ........................27
L
Lamp configuration......................................87
Lamps, disposal ..........................................18
M
Maintenance................................................50
Maintenance and care ........................47
Safety information...............................59
Maintenance intervals .................................54
Maintenance overview.................................50
Make-up ......................................................25
Malfunctions ................................................49
Medication ...................................................25
MP3 music, product information..................17
MP3 player connection................................39
Music channel, choosing .............................41
N
Noise level...................................................85
O
Operating altitude ........................................91
Operation overview .....................................23
Index
Operator commitments ............................... 16
Order numbers............................................ 89
P
Packaging ................................................... 18
Plastic surfaces........................................... 51
Power.......................................................... 85
Power levels of the lamps........................... 86
Power, switching off.................................... 48
Preparation time ......................................... 26
Proper use .................................................. 16
Protective goggles ................................ 25, 26
Sunbed description ..................................... 20
Sunbed, how to use it.................................. 25
Switching off the sound............................... 44
Switching on AROMA.................................. 35
Switching VITALIZER on............................. 37
T
Tanning ....................................................... 25
Tanning instructions .................................... 25
Technical data............................................. 85
Temperature, regulating.............................. 31
Timer ........................................................... 26
R
Rated power of the lamps........................... 86
Relamping................................................... 59
Running time of accent lighting................... 46
U
Using the sunbed ........................................ 25
UV low pressure lamps
replacing................................................ 60, 63
S
Safety information, maintenance ................ 59
Selecting audio system............................... 41
Showering................................................... 25
Skin sensitivity ............................................ 25
Skin types ..................................................... 3
Soiling (VITALIZER) ................................... 53
Spare parts ................................................. 47
Order-No. ........................................... 89
Starter ......................................................... 87
Starting tanning........................................... 26
V
Ventilation data, see Planning Manual........ 91
VITALIZER canister, replacing.................... 82
Volume........................................................ 44
97
Index
98
Separate here
1005378_S50_S55_Series_US_en_080130.qxd
30.01.2008
18:01 Uhr
Seite 1
S-50 / S-55 Series
Soltron, a Division of JK-Products & Services, Inc.
1 Walter Kratz Drive
Jonesboro, AR 72401
Phone: 800.643.0086 (Toll-free)
Fax: 870.935.3618
Website: www.soltron.us
1005378
E-Mail: sales@soltron.us