BR1000SS
Fridge for the KC1000 Kegerator
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
Important Safety Information
Improper handling can cause serious damage to the EdgeStar kegerator and/or injury to the user. This kegerator is
designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may
invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other
technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire, electric shock or injury.
Electrical Safety
 Do not exceed the power outlet ratings.
 It is recommended the kegerator be connected on
its own circuit.
 The unit must be installed in accordance with
state and local electrical codes.
 A standard electrical supply (115 V, 60Hz), that is
properly grounded in accordance with the
National Electrical Code and local codes and
ordinances is required.
 Use outlets that cannot be turned off by a switch
or pull chain.
 Always turn the unit off and unplug it from the
outlet when cleaning.
 Unplug the unit if it is not going to be used for an
extended period of time.
 Do not operate the unit with a power plug missing
the ground plug, a damaged cord or a loose
socket.
 Be sure the kegerator is properly grounded.
 Never plug or unplug the unit with wet hands.
 Do not bypass, cut or remove the grounding plug.
 Do not use extension cords or power strips with
this unit. You may need to contact your electrician
if it is necessary to use a longer cord or if you do
not have a grounded outlet. Do not modify the
power cord’s length or share the outlet with other
appliances.
 If the power cord is damaged, it must be replaced
by the manufacturer or a qualified technician.
 Never repair the unit while it is plugged in.
 Immediately unplug the unit if it makes strange
sounds, emits smells or smoke comes out of it,
and contact customer service.
 Do not remove any part of the casing unless
instructed by an authorized technician.
 You should never attempt to repair the unit
yourself.
 Contact customer service for service options if the
unit needs service.
i
General Safety
 To prevent back and other types of injuries, use at
least two people to move and install the kegerator.
 This unit is not intended for use by persons,
including children, with reduced physical, sensory or
mental capabilities, unless they have been given
supervision or instruction concerning the use of the
appliance by the person(s) responsible for their
safety.
 Install the unit in a well-ventilated area where the
ambient temperature is above 50°F and below 95°F.
 The temperature range for this kegerator is
optimized for beverage storage. Perishable food
items may require a different storage environment.
 Do not place hot or warm items into the kegerator
before they cool down to room temperature.
 This unit is designed to be installed indoors, and
protected from rain, sleet, snow, and/or moisture.
 This unit is not intended to be used by children.
 Children should be supervised to ensure that they
do not play with this product.
 Never allow children to crawl inside the kegerator. If
disposing the unit, remove the door.
 Do not use this unit near flammable gas or
combustibles, such as gasoline, benzene, thinner,
etc.
 Do not place the unit near heat sources such as
ovens, grills, or direct sunlight.
 Only use in an upright position on a flat, level
surface and provide proper ventilation.
 Do not pinch or kink the power supply line between
the unit and cabinet.
 Do not leave any cleaning solutions in the unit
 Do not use solvent-based cleaning agents or
abrasive solutions to clean the unit as they may
damage the interior and exterior.
 Do not place any other appliances on top of the unit.
 Do not turn the unit upside down, on its side, or at
an angle off level.
 If your model is equipped with a lock, take care to
keep the keys away from children.
 Do not move the unit without emptying the contents
and securing the door in a closed position.
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................. I
INTRODUCTION ................................................................................................... 1
PARTS IDENTIFICATION ..................................................................................... 2
BACK VIEW .......................................................................................................... 2
FRONT VIEW ........................................................................................................ 2
PROPER LOCATION ............................................................................................ 3
INSTALLING THE KEGERATOR ......................................................................... 3
ELECTRICAL REQUIREMENTS ................................................................................ 3
Recommended grounding method ................................................................ 4
LEVELING THE KEGERATOR .................................................................................. 4
OPERATION .......................................................................................................... 5
INSTALLATION CHECK LIST BEFORE OPERATION .................................................... 5
USING THE TEMPERATURE CONTROL PANEL ......................................................... 5
NORMAL SOUNDS ................................................................................................ 6
PREPARING THE KEGERATOR FOR STORAGE ......................................................... 6
CLEANING AND MAINTENANCE ........................................................................ 6
EXTERIOR CLEANING ........................................................................................... 7
INTERIOR CLEANING ............................................................................................. 7
TROUBLESHOOTING .......................................................................................... 7
TROUBLESHOOTING CONTINUED ........................................................................... 8
SPECIFICATIONS ................................................................................................. 9
EDGESTAR LIMITED WARRANTY ................................................................... 10
First Time Operating Instructions
Before use, make sure all packaging labels and materials are all removed from
the unit. Be sure to keep track of all included parts and pieces before discarding
packaging materials. It is advised that you keep the original box and packaging
materials in case you are ever to move or ship the appliance in the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling
components time to settle from transit. The instruction manual should be read
before use.
This owner’s manual is provided for reference use only. Specifications may
change without prior notice. Refer to the product label on the back of your
kegerator for the latest technical information.
EdgeStar Kegerator
ii
Introduction
Thank you for purchasing this EdgeStar kegerator. We are glad you chose us.
We believe that your purchase of this product opens a relationship between you
and EdgeStar. We will provide the customer support needed to nurture that
relationship.
This manual contains important information regarding the proper installation, use
and maintenance of your kegerator. Following this manual will ensure that your
product will work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport
your kegerator.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located on the
ratings label on the back of your unit and are needed to
obtain warranty service. You may also want to staple your
receipt to this manual as it is the proof of your purchase, and
is also needed for service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer service:
1

If you received a damaged product, immediately contact the retailer or
dealer that sold you the product.

Read and follow this instruction manual carefully to help you install, use
and maintain your kegerator.

Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.

Visit us on the web at http://www.edgestar.com to register your
product, download product guides, additional troubleshooting resources
and up-to-date information.

If you need warranty service, our friendly customer service
representatives are available via email at service@edgestar.com or by
telephone at 1 (866) 319-5473.
Parts Identification
Front View
Top Cover
Internal Fan
Opening for
Dispense Tower
Switch for
Internal Light
Control Panel
Cold Plate
Recessed
Handle
Door
Leveling
Foot
Compressor
Step
Tip: Gather the model
and serial number
from the product label
and write them down
before installing the
kegerator.
Back View
Water Pan
Compressor
EdgeStar Kegerator
2
NOTE: This appliance is
designed for “indoor” use
only and should not be
used outdoors.
PROPER LOCATION
To ensure the kegerator will last, install it in a location where there
is proper air circulation and electrical connections. Keep the
refrigerator away from heat and direct sunlight. This refrigerator is
designed for indoor use only and should not be used outdoors. It
should not be placed in a built-in or recessed area as it is designed
to be a freestanding kegerator. The following dimensions are the
recommended clearances around the beer dispenser.
Sides
Back
2 to 3” (76mm)
4 to 5” (127 mm)
UNPACKING ACCESSORIES AND
INVENTORY
Proper Location
Installing the Kegerator
The kegerator should be installed in accordance with local electrical code
requirements. The kegerator should also be placed in a location that is
strong enough to support its total weight, keeping in mind that it will weigh
substantially more when fully loaded than when empty.
Before you plug the kegerator into a power supply, be sure to let it stand
upright for at least 24 hours to allow the compressor’s oils to settle.
Unpacking the Kegerator
WARNING: Use two more people to move and install the kegerator.
Failure to do so can result in back or other injury. Carefully remove the
packaging materials. Remove any shipping tape and glue from your
kegerator before using. Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your kegerator.
IMPORTANT: Do not remove any safety, warning, or product information
labels from your kegerator.
Electrical Requirements
ELECTRIC SHOCK HAZARD!

Plug into a grounded 3-prong outlet.

Never remove the grounding prong from the plug.

Never use an adapter to bypass the grounding prong.

DO NOT use an extension cord.

Failure to follow these instructions can result in fire, electrical
shock, or death.
Before you move your kegerator into its final location, it is important to
make sure you have the proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in
accordance with the National Electrical Code and local codes and
ordinances, is required.
3
It is recommended that a separate circuit, serving only your
kegerator, be provided. Use receptacles that cannot be turned off
by a switch or pull chain. The fuse (or circuit breaker) size should
be 15 Amps.
Recommended grounding method
For your personal safety, this appliance’s plug must be grounded. It
is equipped with a 3-prong power supply cord. To minimize
possible shock hazard, the cord must be plugged into a mating 3prong wall socket and grounded in accordance with the National
Electrical Code as well as local codes and ordinances. In the event
of a malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for electrical
current.
• Plug your appliance into an exclusive, properly installed, grounded
wall outlet. Do not under any circumstances, cut or remove the third
(ground) prong from the power cord.
• Any questions concerning power and/or grounding should be
directed toward a certified electrician.
• This appliance requires a standard 110~120 volt, 60Hz electrical
outlet with three-prong ground.
• Do not use outlet adaptors. No other appliance should be plugged
into the same outlet. Be sure that the plug is fully inserted into the
outlet.
Leveling the Kegerator
Note: A detailed
installation guide of all
the dispense kit
components may be
included with your
kegerator depending on
the type purchased.
It is important for the kegerator to be leveled for optimum efficiency.
It can be raised or lowered by rotating the plastic sheaths around
each of the feet on the bottom of the machine. If you find that the
surface is not level, rotate the feet until the kegerator becomes
level. You may need to make several adjustments to level it.
1. If available, place a carpenter’s level on top of the product to see if the
kegerator is level from front to back and side to side.
2. To adjust the height of the kegerator, simply turn the feet (Right =
Lower / Left = Raise)
IMPORTANT: Kegerator should be level before installation
EdgeStar Kegerator
4
OPERATION
Installation Check List before Operation
Note: Allow the
refrigerator to stand in
an upright position for
24 hours before turning
on the power. This will
ensure that the coolant
has settled.
1. Have all packing materials and tape been removed from the
interior and exterior of the kegerator?
2. Have the installation instructions been followed, including
connecting the machine to electricity? And has proper grounding
been installed for the kegerator?
3. Has the machine been leveled?
4. Is the kegerator in a site where the ambient temperature is
between 50º F and 95º F all year round?
Using the Temperature Control Panel
Note: Whether your
kegerator can reach cooler
temperature depends on the
ambient environmental
conditions.
This kegerator has digital control panel located on the top of the
inside of the cabinet. Pressing the temperature buttons will make
the unit colder or warmer. Press the “-“ button to lower the
temperature by one degree. Press the “+” to raise the temperature
by one degree. This unit has a temperature range of 32-46° F.
Press the F/C button to change the display from °F to °C.
Caution: If you powered off
the unit, please wait at least
5 minutes before powering it
back on.
5
The unit will run automatically once plugged in. Unplug the unit to
turn it off.
Normal Sounds
Your new kegerator may make sounds that are not familiar to you.
Most of the new sounds are normal. Hard surfaces like the floor or
walls can make the sounds seem louder than they actually are. The
following describes the kinds of sounds that might be new to you
and what may be making them.

Rattling noises may come from the flow of the refrigerant or
the water line. Items stored on top of the kegerator can also
make noises.

The high efficiency compressor may make a pulsating or
high-pitched sound.

Water running from the evaporator to the water bin may
make a splashing or sound.

As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your kegerator.

Cracking or popping sounds are caused by the expanding
and / or contracting of the cooling coils.
Preparing the Kegerator for Storage
If the kegerator will not be used for a long time, or is to be moved to
another place, it will be necessary to defrost the unit and dry the
interior.
IMPORTANT:
• Do not touch the power plug
when your hands are wet.
• Never unplug the unit by
pulling on the plug.
1. Disconnect the unit from the power supply by removing the
power plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent
mold, mildew and unpleasant smells.
CAUTION: Store the unit out of the reach of children. If you have
children, you may want to take additional precautions such as
removing the door to prevent a child from being trapped inside the
unit!
CLEANING AND MAINTENANCE
Cleaning accessories and
equipment can be purchased
at Kegerator.com
EdgeStar Kegerator
A regular cleaning once every 2 weeks of the faucet, beer hose,
and keg coupler is extremely important when the Draft Beer
Dispenser is used frequently. If this is not performed, the beer will
foam. Additionally bacteria, yeast, mold, and beer stone will build
up and quickly degrade the quality of draft beer. A few minutes
spent cleaning on a regular basis will add life to your system, and
improve the quality of your draft beer!
6
Exterior Cleaning
The door and cabinet may be cleaned with a mild detergent and
lukewarm water solution such as 2 tablespoons of baking soda to 1
quart of water.
Do not use solvent based or abrasive cleaners. Use a soft sponge
and rinse with clean water. Wipe with a soft clean towel to prevent
water spotting. If the door panel is stainless steel, it can discolor
when exposed to chlorine gas and moisture. Clean stainless steel
with a cloth dampened with a mild detergent and warm water
solution. Never use an abrasive or caustic cleaning agent.
Interior Cleaning
The kegerator’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the door and remove the contents.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reconnect power to the unit.
TROUBLESHOOTING
Before Calling for Help
If the unit appears to be malfunctioning, read through the
OPERATION section of this manual first. If the problem persists,
check the Troubleshooting Guide below and on the following page.
The problem could be something that can easily be solved or
explained.
Symptoms
The kegerator turns on
and off frequently.
7
Possible causes
Solutions
The room temperature is
higher than the
recommended ambient
environment.
Run the unit at the appropriate ambient temperature.
The door is being opened
often.
Minimize the number of times the door is opened.
The door is not completely
closed.
Make sure the door is completely closed.
The door gasket is not
sealing properly.
Make sure the door gasket is properly sealing.
Troubleshooting continued
Issue
The kegerator does not
turn on.
The kegerator will not
reach the desired
temperature
Possible cause
Solution
There is a power failure.
Ensure the unit is plugged in and the power outlet has
power.
The unit is not plugged in.
Plug the unit in to a power outlet that has sufficient
amperage.
A house fuse has blown or
the circuit breaker is tripped.
Replace the broken fuse in your fuse box or reset the
breaker.
The unit is placed too close
to a heat source.
Keep the unit away from direct sun light or other heat
sources.
The door is opened too
frequently or for a long
period of time.
Close the door tightly and do not open the door too
frequently or for a long period of time.
Certain sounds are normal.
Read the “Normal Sounds” section.
The unit is not level or is
touching another appliance.
Check to make sure that the kegerator is level, and that it
is not in contact with another appliance or furniture.
The unit is not grounded
properly.
Contact your local electrician to test your electrical
grounding system.
The kegerator is making
strange noises
The body of the kegerator
is electrified.
The environment is humid.
Frost is forming in the
kegerator.
The ambient temperature is
too low.
The door is being opened
too frequently.
Your unit is not level.
The door gasket is dirty.
The door will not shut
properly.
EdgeStar Kegerator
If frost builds up manual defrosting may be required.
You can try running the kegerator on a warmer
temperature setting, minimizing the number of times you
open the door, or unplugging the unit to allow the frost to
melt.
Make sure the unit is on a level surface.
Clean the door gasket.
The door gasket is not
installed correctly.
Make sure the door gasket is properly installed.
The keg used is too large
This kegerator will not fit oversized kegs. Please check
the specifications on the next page for proper keg loading.
8
Specifications
Description of product
Freestanding Kegerator
Model
BR1000SS
Fridge for the KC1000 Kegerator
Voltage/Frequency
AC 115V~60Hz
Amperage
1.2A
Color
Black Cabinet; Stainless Steel
Door
Storage Capacity Options


1 Sixth Barrel Keg
or
1 Cornelius Keg
Refrigerant
R600a
Dimensions
(Height x Width x Depth )
20.1" x 17.52" x 32.72"
Weight
63.8 pounds
Note: Technical data and performance information is provided for
reference only.
Specifications are subject to change. Check the rating label on the
kegerator for the most accurate information.
9
EdgeStar Limited Warranty
One (1) Year Parts & Ninety (90) Days Labor
This product is warranted by EdgeStar to be free from defective workmanship and materials, subject to any conditions set
forth as follows:
WHAT IS COVERED:
LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at an
authorized EdgeStar repair facility. At its option, EdgeStar will repair the product with new or remanufactured parts, or
exchange the defective product with a new, refurbished, or remanufactured product. If a product is replaced, it will carry the
remaining warranty of the original product. After the ninety (90) day period, EdgeStar will no longer be responsible for labor
charges incurred. All defective products and parts covered by this warranty will be repaired or replaced on a mail-in basis to
an EdgeStar authorized repair facility.
PARTS: For a period of ONE (1) YEAR from the date of original purchase, EdgeStar will supply new, rebuilt, or refurbished
parts free of charge. EdgeStar may request a defective part be returned in exchange for the replacement part. All
replacement parts or products will be new, remanufactured, or refurbished. All products and parts replaced by EdgeStar
under warranty service become the property of EdgeStar.
This warranty applies to the original purchaser only, and only covers defects in workmanship experienced during operation of
the product under normal service, maintenance, and usage conditions. This warranty applies to the purchase and use of this
product in residential settings within the United States of America.
WHAT IS NOT COVERED:
The following limitations apply to the coverage of this warranty. This warranty does not cover:
 Labor charges for installation, setup or training to use the product.
 Shipping damage, and any damage caused by improper packaging for shipment to an authorized service center, and
any damaged caused by improper voltage or any other misuse, including abnormal service, handling, or usage.
 Cosmetic damage such as scratches and dents.
 Normal wear and tear on parts or replacement of parts designed to be replaced, e.g. filters, cartridges, batteries.
 Service trips to deliver, pick-up, or repair, install the product, or to instruct in proper usage of the product.
 Damages or operating problems resulting from misuse, abuse, operation outside environmental specifications, uses
contrary to instructions provided in the owner’s manual, accidents, acts of God, vermin, fire, flood, improper
installation, unauthorized service, maintenance negligence, unauthorized installation or modification, or commercial
use.
 Labor charges incurred 91 days or more after the date of original purchase.
 The use of EdgeStar products in commercial settings.
 Optional accessories, attachments, and appearance items.
 Products that have been modified to perform outside of specifications without the prior written permission of
EdgeStar.
 Products lost in shipment, or theft.
 Products sold AS IS or from an unauthorized reseller.
 Products that have had their serial numbers removed or defaced. Products with serial numbers that have been
invalidated.
OBTAINING WARRANTY SERVICE:
If you believe your product is defective, contact EdgeStar Customer Support for troubleshooting assistance and warranty
service at 1-866-319-5473. Please have your serial number and proof of purchase available. Once an EdgeStar authorized
representative has confirmed that your product is defective and eligible for warranty service, the product must be returned to
an EdgeStar repair facility. The purchaser is solely responsible for prepaying all shipping related costs to and from the repair
facility. EdgeStar is not responsible for damage resulting from shipper mishandling or improper packaging. Do not return a
defective product to the place of purchase. Products received without a return authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT
ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY
PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING
WITHOUT LIMITATION, LOST REVENUES OR PROFITS, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT,
TORT, OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
EdgeStar Kegerator
10
EdgeStar Products
500 N. Capital of TX Hwy, Bldg 5
Austin, TX 78746
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: service@edgestar.com
Register your product, download owner’s manuals, access additional troubleshooting
resources, and obtain more information on other great EdgeStar products on the web at:
http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2015 Living Direct, Inc. All rights reserved.
Download PDF
Similar pages