ENGLISH
5PX
5PX
5PX
5PX
5PX
5PX
5PX
5PX
1500i RT2U
2000i RT2U
2200i RT2U
3000i RT2U
3000i RT3U
EBM 48V RT2U
EBM 72V RT2U
EBM 72V RT3U
Installation
and user manual
Copyright © 2010 EATON
All rights reserved.
Service and support:
Call your local service representative
614-07977-00_EN
Certification Standards
UPS directives:
pp Safety:
IEC 62040-1: 2008 (C2)
pp EMC:
IEC 62040-2: 2005
pp Performance:
IEC 62040-3: 2010
CE mark (EN 62040-1: 2008 and EN 62040-2: 2006 (C1))
Class B emission level CISPR 22: 2005 + A2 2006 (EN 55022)
Harmonics emission: IEC 61000-3-2 edition 3.2: 2009
Flickers emission: IEC 61000-3-3 edition 2: 2008
The EC Declaration of Conformity is available upon request for products with a CE mark.
For copies of the EC Declaration of Conformity, contact Eaton Power Quality or check Eaton website:
www.powerquality.eaton.com
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.
Important instructions that must always be followed.
Do not discard the UPS or the UPS batteries in the trash.
This product contains sealed lead acid batteries and must be disposed as it's explain in this manual.
For more information, contact your local recycling/reuse or hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE)
in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.
Information, advice, help.
Page 2
614-07977-00_EN
1. Introduction........................................................................................ 4
1.1 Environmental protection.................................................................................................4
2. Presentation....................................................................................... 5
2.1
2.2
2.3
2.4
2.5
2.6
Standard positions............................................................................................................5
Rear Panels.......................................................................................................................6
Control panel....................................................................................................................7
LCD description................................................................................................................8
Display functions..............................................................................................................9
User settings....................................................................................................................9
3. Installation........................................................................................11
3.1
3.2
3.3
3.4
3.5
3.6
3.7
Unpacking and contents check....................................................................................... 11
Installation in tower position........................................................................................... 12
Installation in rack position............................................................................................. 12
Communication ports..................................................................................................... 13
Connection with a FlexPDU (Power Distribution Unit) module (optional)....................... 14
Connection with a HotSwap MBP module (optional)..................................................... 14
UPS connection without a FlexPDU or HotSwap MBP module..................................... 15
4. Operation......................................................................................... 16
4.1
4.2
4.3
4.4
4.5
4.6
Start-up and Normal operation........................................................................................ 16
Starting the UPS on Battery........................................................................................... 16
UPS Shutdown............................................................................................................... 16
Operation on Battery Power........................................................................................... 16
Return of AC Input Power............................................................................................... 17
UPS remote control functions........................................................................................ 17
5. Maintenance.................................................................................... 18
5.1 Troubleshooting.............................................................................................................. 18
5.2 Battery-module replacement.......................................................................................... 19
5.3 Maintenance on a UPS equipped with the HotSwap MBP module...............................20
6. Appendices....................................................................................... 21
6.1 Technical specifications..................................................................................................21
6.2 Glossary..........................................................................................................................22
614-07977-00_EN
Page 3
ENGLISH
Contents
1. Introduction
Thank you for selecting an EATON product to protect your electrical equipment.
The 5PX range has been designed with the utmost care.
We recommend that you take the time to read this manual to take full advantage of the many features
of your UPS (Uninterruptible Power System).
Before installing 5PX, please read the booklet presenting the safety instructions.
Then follow the indications in this manual.
To discover the entire range of EATON products and the options available for the 5PX range,
we invite you to visit our web site at www.eaton.com or contact your EATON representative.
1.1 Environmental protection
EATON has implemented an environmental-protection policy.
Products are developed according to an eco-design approach.
Substances
This product does not contain CFCs, HCFCs or asbestos.
Packing
To improve waste treatment and facilitate recycling, separate the various packing components.
pp The cardboard we use comprises over 50 % of recycled cardboard.
pp Sacks and bags are made of polyethylene.
pp Packing materials are recyclable and bear the appropriate identification symbol
01
PET
Materials
Abbreviations
Number in
the symbols
Polyethylene terephthalat
PET
01
High-density polyethylene
HDPE
02
Polyvinyl chloride
PVC
03
Low-density polyethylene
LDPE
04
Polypropylene
PP
05
Polystyrene
PS
06
01
PET
Follow all local regulations for the disposal of packing materials.
End of life
EATON will process products at the end of their service life in compliance with local regulations.
EATON works with companies in charge of collecting and eliminating our products at the end of
their service life.
Product
The product is made up of recyclable materials.
Dismantling and destruction must take place in compliance with all local regulations concerning waste.
At the end of its service life, the product must be transported to a processing centre for electrical and
electronic waste.
Battery
The product contains lead-acid batteries that must be processed according to applicable local regulations
concerning batteries.
The battery may be removed to comply with regulations and in view of correct disposal.
Page 4
614-07977-00_EN
2.1 Standard positions
Tower position
D
D
W
W
H
H
Rack position
D
D
H
H
W
Description
Weights (kg/lb)
5PX 1500i RT2U
5PX 2000i RT2U
5PX 2200i RT2U
5PX 3000i RT2U
5PX 3000i RT3U
5PX EBM 48V RT2U
5PX EBM 72V RT2U
5PX EBM 72V RT3U
27.60 / 60.90
28.50 / 62.80
28.50 / 62.80
38.08 / 84.00
37.33 / 82.30
32.80 / 72.30
46.39 / 102.30
44.26 / 97.60
614-07977-00_EN
W
Dimensions (mm/inch)
DxWxH
522 x 441.2 x 86.2 / 20.6 x 17.4 x 3.4
647
497
522
647
497
x
x
x
x
x
441.2
441.2
441.2
441.2
441.2
x
x
x
x
x
86.2 / 25.5 x 17.4 x 3.4
130.7 / 19.6 x 17.4 x 5.1
86.2 / 20.6 x 17.4 x 3.4
86.2 / 25.5 x 17.4 x 3.4
130.7 / 19.6 x 17.4 x 5.1
Page 5
ENGLISH
2. Presentation
2. Presentation
2.2 Rear Panels
5PX 1500i / 2000i
5PX 2200i
(1) USB communication port
(2) RS232 communication port
(3)Connector for automatic recognition
of optional battery modules
(4)Slot for optional communication card
(5)Connector for ROO (remote ON/OFF)
or RPO (Remote Power Off) control
(6)Connector for optional battery
modules
(7)16 A outlet for connection of
equipment (Primary group)
(8)Two groups of 2 programmable
outlets for connection of equipment
(Group 1 and 2)
(9)Groups of 4 outlets for connection of
equipment (Primary group)
(10)Socket for connection to AC-power
source
5PX 3000i
5PX EBM (optional battery module)
(12)Connectors for battery modules
(to the UPS or to the other battery
modules)
(13)Connectors for automatic recognition
of battery modules
Page 6
614-07977-00_EN
2.3 Control panel
The UPS has a five-button graphical LCD. It provides useful information about the UPS itself, load status,
events, measurements and settings.
Power On
Indicator (green)
On battery
Indicator (yellow)
Alarm
Indicator (red)
Normal mode
100%
2.7kW
3kVA
100%
17min
1EBM
Efficiency: 98%
Escape
Up
Down
Enter
On/Off
button
The following table shows the indicator status and description :
Indicator
Green
Yellow
Red
614-07977-00_EN
Status
Description
On
The UPS is operating normally
On
The UPS is on battery mode
Flashing
The battery voltage is below the warning level
On
The UPS has an active alarm or fault. See troubleshooting on page 18 for additional information.
Page 7
ENGLISH
2. Presentation
2. Presentation
2.4 LCD description
As default, or after 5 minutes of inactivity, the LCD displays the screen saver.
The backlight LCD automatically dims after 10 minutes of inactivity. Press any button to restore the screen.
Operation status
Normal mode
100%
2.7kW
3kVA
Load/equipment status
100%
17min
1EBM
Battery status
Efficiency: 98%
Efficiency and load group information
The following table describes the status information provided by the UPS
Note. If other indicator appears, see troubleshooting on page 18 for additional information.
Operation status
Standby mode
Possible cause
Action
The UPS is OFF, waiting for start-up Equipment is not powered until
command from user
button is not pressed.
Normal mode
The UPS is operating normally.
The UPS is powering and protecting
the equipment.
In AVR mode
The UPS is operating normally but
the utility voltage is outside normal
mode thresholds.
The UPS is powering the
equipment through a Automatic
Voltage Regulation device.
The equipment is still normally
protected.
A utility failure has occured and
the UPS is in Battery mode.
The UPS is powering the equipment
with the battery power. Prepare
your equipment for shutdown.
The UPS is in battery mode and
the battery is running low.
This warning is approximate, and
the actual time to shutdown may
vary siginificantly.
Depending on the UPS Load and
number of Extended Battery
modules (EBMs), the "Battery Low"
warning may occur before the
battery reach 25 % capacity.
Load protected LED is ON
No beep
On Battery
Battery LED is on
1 beep every 10 seconds
End of backup time
Battery LED is blinking
1 beep every 3 seconds
Page 8
614-07977-00_EN
2.5 Display functions
Press the Enter (
) button to activate the menu options. Use the two middle buttons (
through the menu structure. Press the Enter (
) button to select an option. Press the
or return to the previous menu.
and ) to scroll
button to cancel
Menu map for Display Functions.
Main menu
Measurements
Control
Settings
Fault log
Identification
Submenu
Display information or Menu function
Load W VA / Load A pf / Output V Hz / Input V Hz /
Battery V min / Efficiency / Power usage
Load Segments
Group 1: ON / OFF
Group 2: ON / OFF
These commands overrule user settings for load segments.
Start battery test
Starts a manual battery test
Reset fault state
Clears active fault
Restore factory settings Returns all settings to original values (UPS restart required)
Reset power usage
Clears power usage measurements
Local settings
Sets product general parameters
Input / output settings Sets Input and output parameters
ON / OFF settings
Sets ON / OFF conditions
Battery settings
Sets battery configuration
Displays event log or alarms
UPS Type / Part Number / Serial Number / Firmware release /
Com card address
2.6 User settings
The following table displays the options that can be changed by the user.
Description
Language
Local settings
LCD settings
Audible alarm
Output voltage
Input thresholds
In/Out settings
Sensitivity
Load segments Auto start delay
614-07977-00_EN
Available settings
[English] [Français] [Deutsch]
[Italiano] [Português] [Español]
[Русский]
Menus, status, notices and alarms,
UPS fault, Event Log data and
settings are in all supported
languages.
Authorises to modify LCD screen
brightness and contrast to be
adapted to room light conditions.
[Yes] [No]
Authorises to enable or disable the
buzzer if an alarm occurs.
[200 V] [208 V] [220 V] [230 V]
[240 V]
[Normal mode] [Extended mode]
Extended mode authorises lower
input voltage (150 V) without
transferring to battery.
This can be used if the load can
withstand low voltage supply.
[High] [Low]
High: for sensitive equipment,
UPS will easily transfer to battery
when utility conditions are
becoming bad.
Low: for equipment that can
withstand bad utility conditions,
in that case, the UPS will not
transfer to battery.
[No Delay] [1 s] [2 s]…[65354 s]
The equipment are powered with
the specified delay.
Default settings
English
User selectable when UPS is
powered for the first time.
Yes
230 V
User selectable when UPS is
powered for the first time.
Normal mode
High
Group 1: 3 s
Group 2: 6 s
Page 9
ENGLISH
2. Presentation
2. Presentation
Description
Load segments
- Auto shutdown
delay
Available settings
[Disable] [0s] [1 s] [2 s]…[65354 s]
During a power outage, authorises
to keep some equipment running
while turning off other equipment.
This feature allows to save battery
power.
In/Out settings
Overload pre[5 %] [10 %] [15 %] [20 %] ... [100 %]
alarm
[105 %]
Gives a warning when a predefined
critical percentage of load is
reached.
Cold start
[Disable] [Enable]
Authorises the product to start on
battery power.
Forced reboot
[Disable] [Enable]
If set to Enable, when a shutdown
sequence is sent through
communication port, it allows,
if mains recovers during the
sequence, to shutoff the output
during 10 s.
Auto restart
[Disable] [Enable]
Authorises the product to restart
automatically when mains recovers
after a complete battery discharge.
ON/OFF settings
Energy saving
[Disable] [Enable]
If Enable, UPS will shutdown after
5min of back-up time, if no load is
detected on the output.
Sleep mode
[Disable] [Enable]
If disable, LCD and communication
will turn OFF immediately after
UPS is OFF.
If enable, LCD and communication
stays ON 1h30 min after UPS is OFF.
Remote command [Disable] [Enable]
If enable, shutdown or restart
commands from software are
authorised.
Automatic battery [No test] [Every day] [Every week]
test
[Every month]
Available only if battery charge
mode is set to constant charge.
Low battery warn- [10 %] [20 %] [30 %] [40 %] [50 %]
ing
[60 %] [70 %] [80 %] [90 %]
The alarm triggers when the set
percentage of battery capacity is
reached during a back-up time.
Restart battery
[10 %] [20 %] [30 %] [40 %] [50 %]
level
[60 %] [70 %] [80 %] [90 %] [100 %]
If set, automatic restart will occur
only when percentage of battery
Battery settings
charge is reached.
Battery charge
[ABM cycling] [Constant charge]
mode
EBM number
[0] [1] [2] [3] [4]
setting
Using standard EBM, UPS detects
automatically the amount of EBM
connected.
Deep discharge
[Yes] [No]
protection
If set to Yes, the UPS automatically
prevents battery from deep
discharge by adapting end of
back-up time voltage threshold.
Page 10
Default settings
Group 1: Disable
Group 2: Disable
[105 %]
Enable
Enable
Enable
Disable
Disable
Enable
Every week
(in constant charge,
otherwise following ABM
battery test method)
20 %
0%
ABM cycling
EBM automatic detection,
otherwise 0
Yes
614-07977-00_EN
3.1 Unpacking and contents check
31
32
30
38
40
33
39
35
36
41
44
(30) 5PX UPS
(31) c onnection cable to AC-power source
(5PX 2200 and 3000 models only)
(32) 2
connection cables for the protected
equipment
(33) RS232 communication cable
(34) USB communication cable
(35) 2 cable locking systems
(36) Software CD-ROM
(37) Manual CD-ROM
(38) Safety instructions
(39) Quick start
34
37
42
43
45
46
Elements supplied depending on the version or
optional
(41) 2
supports for tower position
(RT 2U version only)
(42) FlexPDU module (optional)
(43) c onnection cable between FlexPDU module
and UPS
(44) N
MC communication card (optional, standard
on Netpack versions)
(45) HotSwap MBP module (optional)
(46) c onnection cables between HotSwap MBP
module and UPS
(40) Mounting kit for 19-inch enclosures
Packing materials must be disposed of in compliance with all local regulations concerning waste.
Recycling symbols are printed on the packing materials to facilitate sorting.
614-07977-00_EN
Page 11
ENGLISH
3. Installation
3. Installation
3.2 Installation in tower position
Note. The two supports for the tower position are used on the RT 2U version only.
3.3 Installation in rack position
Follow steps 1 to 4 for module mounting on the rails.
1
1
2
3
3
4
4
The rails and necessary hardware are supplied by EATON.
Page 12
614-07977-00_EN
3.4 Communication ports
Connection of RS232 or USB communication port (optional)
The RS232 and USB communication ports cannot operate simultaneously.
1. C
onnect the RS232 (33) or
USB (34) communication cable
to the serial or USB port on
the computer equipment.
2. C
onnect the other end of the
communication cable (33) or
(34) to the USB (1) or RS232
(2) communication port on
the UPS.
The UPS can now communicate
with EATON power management
software.
Installation of the communication cards (optional, standard on the Netpack versions)
It is not necessary to shutdown
the UPS before installing
a communication card.
1. R
emove the slot cover (4)
secured by screws.
2. Insert the communication
card in the slot.
3. Secure the card cover with
the 2 screws.
Characteristics of the contact communication port (optional)
pp Pins 1, 3, 4, 5, 6, 10: not used
pp Pin 2: common (user)
pp Pin 7: low battery
pp P
in 8: operation on battery
power
pp P
in 9: UPS ON, equipment
supplied
n.o.: normally open contact
When a signal is activated, the contact is closed between the common (pin 2) and the pin
for the corresponding signal.
Contact characteristics (optocoupler)
pp Voltage: 48 V DC max
pp Current: 25 mA max
pp Power: 1.2 W
614-07977-00_EN
Page 13
ENGLISH
3. Installation
3. Installation
3.5 Connection with a FlexPDU (Power Distribution Unit) module (optional)
1. 5
PX 2200i / 3000i: connect
the UPS input socket (10) to
the AC-power source using
the cable (31) supplied.
5PX 1500i / 2000i: use the power
cable of the protected equipment.
5PX
2. 5
PX 2200i / 3000i: connect the
input socket on the FlexPDU
module (50) to the UPS outlet
(7) using the cable (43) supplied.
5PX 1500i / 2000i: connect the
input socket on the FlexPDU
module (50) to one of the
outlets (9).
The cable and the connectors
are marked in red.
43
FlexPDU
48
47
49
50
3. C
onnect the equipment to the
outlets (47), (48) and (49) on the
FlexPDU module. These outlets
differ, depending on the version
of the FlexPDU module.
4. F
it the connection securing
system that prevents the plugs
from being pulled out
accidentally.
3.6 Connection with a HotSwap MBP module (optional)
The HotSwap MBP module makes it possible to service or even replace the UPS without affecting the connected
loads (HotSwap function).
1. Connect the input socket (58) on
the HotSwap MBP module to the
5PX
AC-power source using the cable
(31) supplied.
2. C
onnect the UPS input socket (10)
to the “UPS Input” (57) on the
HotSwap MBP module, using the
cable (46) supplied. These cables
and the connectors are marked
blue.
46
HotSwap MBP
51
52 53 54
55
56
57
58
3. C
onnect the UPS outlet (7) to
the “UPS Output” (56) on the
HotSwap MBP module, using the
cable (46) supplied.
5PX 1500i: connect one of the UPS
outlets (9) to the “UPS Output”
(56) on the HotSwap MBP
module.
These cables and the connectors
are marked in red.
4. C
onnect the equipment to the outlets (51) and (52) on the HotSwap
MBP module. These outlets differ,
depending on the version of the
HotSwap MBP module.
Caution. Do not use UPS outlets
(8) and (9) to supply equipment
because use of switch (55) on the
HotSwap MBP module would cut
supply to the equipment.
Page 14
614-07977-00_EN
HotSwap MBP module operation
The HotSwap MBP module has a rotary
switch (55) with two positions:
53
54
Normalthe load is supplied by the UPS,
LED (53) is on.
Bypassthe load is supplied directly by
the AC-power source. LED (54)
is on.
55
UPS start-up with the HotSwap MBP module
1. Check that the UPS is correctly connected to the HotSwap MBP module.
2. Set switch (55) to Normal position.
3. Start the UPS by pressing the ON/OFF button
on the UPS control panel.
The load is supplied by the UPS.
LED (53) "UPS ON - OK to switch" on the HotSwap MBP module goes ON.
HotSwap MBP module test
1. Set switch (55) to Bypass position and check that the load is still supplied.
2. Set switch (55) back to Normal position.
3.7 UPS connection without a FlexPDU or HotSwap MBP module
Check that the indications on the name plate located on the back of the UPS correspond to the AC-power
source and the true electrical consumption of the total load.
31
7
9
8
10
32
35
1. 5
PX 1500i / 2000i: connect the
UPS input socket (10) to the
AC-power source using the cable
of the protected equipment.
5PX 2200i / 3000i: connect the
supplied cable (31) (250 V 16 A) to the socket (10), then
to the AC-power source.
2. C
onnect the loads to the UPS
using the cables (32).
It is preferable to connect the
priority loads to the four outlets
marked (9) and the non-priority
loads to the four outlets marked
(8) that can be programmed in
pairs (1 and 2).
For the 5PX 2200i / 3000i models,
connect any high-power devices
to the 16 A outlet (7).
To program shutdown of outlets
(8) during operation on battery
power and thus optimise
the available backup time,
please check the in/out settings.
3. F
it the connection securing system
(35) that prevents the plugs from
being pulled out accidentally.
Note. T
he UPS charges the battery as soon as it is connected to the AC-power source, even if
button
is not pressed.
Once the UPS is connected to the AC-power source, eight hours of charging are required before the
battery can supply the rated backup time.
614-07977-00_EN
Page 15
ENGLISH
3. Installation
4. Operation
4.1 Start-up and Normal operation
To start the UPS:
1. Verify that the UPS power cord is plugged in.
2. The UPS front panel display illuminates and shows EATON logo.
3. Verify that the UPS status screen shows .
4. Press the
button on the UPS front panel for at least 2 seconds.
The UPS front panel display changes status to "UPS starting...".
5.Check the UPS front panel display for active alarms or notices. Resolve any active alarms before
continuing. See "Troubleshooting" on page 18.
If the
indicator is on, do not proceed until all alarms are clear. Check the UPS status from the front
panel to view the active alarms. Correct the alarms and restart if necessary.
6.Verify that the
indicator illuminates solid, indicating that the UPS is operating normally and any loads
are powered and protected.
The UPS should be in Normal mode.
4.2 Starting the UPS on Battery
Before using this feature, the UPS must have been powered by utility power with output enabled at
least once.
Battery start can be disabled. See the "Cold start" setting in "ON/OFF Settings" on page 10.
To start the UPS on battery:
button on the UPS front panel until the UPS front panel display illuminates and shows
1.Press the
a status of "UPS starting...".
The UPS cycles through Standby mode to Battery mode. The
indicator illuminates solid.
The UPS supplies power to your equipment.
2.Check the UPS front panel display for active alarms or notices besides the "Battery mode" notice
and notices that indicate missing utility power. Resolve any active alarms before continuing.
See "Troubleshooting" on page 18.
Check the UPS status from the front panel to view the active alarms. Correct the alarms and restart
if necessary.
4.3 UPS Shutdown
To shut down the UPS:
button on the front panel for three seconds.
1. Press the
The UPS starts to beep and shows a status of "UPS shutting OFF...". The UPS then transfers to Standby
mode, and the
indicator turns off.
4.4 Operation on Battery Power
Transfer to battery power
pp The connected devices continue to be supplied by the UPS when AC input power is no longer available.
The necessary energy is provided by the battery.
pp The
and
indicator illuminates solid.
pp The audio alarm beeps every ten seconds.
The connected devices are supplied by the battery.
Page 16
614-07977-00_EN
Low-battery warning
pp The
and
indicator illuminates solid.
pp The audio alarm beeps every three seconds.
The remaining battery power is low. Shut down all applications on the connected equipment because
automatic UPS shutdown is imminent.
End of battery backup time
pp LCD displays "End of backup time".
pp All the LEDs go OFF.
pp The audio alarms stops.
4.5 Return of AC Input Power
Following an outage, the UPS restarts automatically when AC input power returns (unless the restart
function has been disabled) and the load is supplied again.
4.6 UPS remote control functions
5PX offers a choice between two remote control functions.
pp RPO: Remote Power Off allow a remote contact to be used to disconnect all the equipment connected to
the UPS. Restarting the UPS requires manual intervention.
pp ROO: Remote ON/OFF allows remote action of button
to shut down the UPS.
These functions are obtained by opening a contact connected between the appropriate pins of connector (5)
on the rear panel of the UPS (see figures below).
5
Remote control connection and test
1. Check that the UPS is OFF and disconnected from the AC input source.
2. Remove connector (5) after unscrewing the screws.
3. Connect a normally closed volt-free contact (60 V DC / 30 V AC max., 20 mA max., 0.75 mm2 cable
cross-section) between the two pins of connector (5) (see diagram).
Contact open: UPS shutdown
Contact closed: UPS start-up (UPS connected to AC power and AC power is available)
Note. The local ON/OFF control using button
overrides the remote-control function.
Contact open: UPS shutdown, LED
goes ON.
To return to normal operation, deactivate the remote external contact and restart
the UPS by pressing button .
4. Plug connector (5) into the back of the UPS.
5. Connect and restart the UPS following the previously described procedures.
6. Activate the external remote shutdown contact to test the function.
Warning. This connector must only be connected to SELV (Safety Extra-Low Voltage) circuits.
614-07977-00_EN
Page 17
ENGLISH
4. Operation
5. Maintenance
5.1 Troubleshooting
Operation status
Batteries disconnected
Possible cause
The UPS does not recognise
the internal batteries
The batteries are disconnected
Action
If the condition persists, contact
your service representative
Verify that all batteries are properly
connected. If the condition persists,
contact your service representative.
Overload
Power requirements exceeds the
UPS capacity (greater than 105 %
of nominal)
End of battery life
The end of the battery life is
reached.
Remove some of the equipment
from the UPS. The UPS continues
to operate, but may shutdown if the
load increases. The alarm resets
when the condition becomes
inactive.
Contact your service representative
for battery replacement.
Event
An UPS event occurs
UPS fault
Example:
Remote Power OFF, the RPO
contact has been activated to
shutdown the UPS and now
prevents restart.
An internal failure occured with the
UPS
Set the contact back to its normal
position and press
button
to restart.
The UPS does not protect the
equipment anymore.
Note. the alarm message and
the UPS Serial Number, then contact
your service representative.
Troubleshooting a UPS equipped with the HotSwap MBP module
1
Indication
The load is no longer supplied
when the rotary switch (55) on
the HotSwap MBP module is
set to Bypass position.
2
The load is no longer supplied
when the rotary switch (55) on
the HotSwap MBP module is
set to Normal position.
3
The load is no longer supplied
after AC-power fails.
Diagnostic
l The protected devices
are connected to the UPS
output instead of to the
HotSwap MBP module.
l The AC-power cord is
connected to the UPS input
instead of to the HotSwap
MBP module.
l The UPS is shut down.
l The wiring between the
UPS and the HotSwap MBP
module is incorrect.
l
l
Page 18
Correction
Check the wiring between
the UPS and the HotSwap MBP
module (see section 3.6).
l
l
he rotary switch (55) on
T
l
the HotSwap MBP module
is set to Bypass position.
l
The wiring between the
UPS and the HotSwap MBP
module is incorrect.
Start the UPS.
Check the wiring between
the UPS and the HotSwap
MBP module
(see section 3.6).
Set the rotary switch (55)
on the HotSwap MBP
module to Normal position.
Check the wiring between
the UPS and the HotSwap
MBP module
(see section 3.6).
614-07977-00_EN
5.2 Battery-module replacement
Safety recommendations
The battery can cause electrocution and high short-circuit currents. The following safety precautions
are required before servicing the battery components:
pp remove watches, rings, bracelets and all other metal objects from the hands and arms,
pp use tools with an insulated handle.
Battery-tray removal
A - Remove the middle part.
B-R
emove the left-hand side of the front
panel by pushing the button and then
by sliding the part.
B
A
C-D
isconnect the battery block by
separating the two connectors
(never pull on the wires).
C
D-R
emove the metal protection cover
in front of the battery (two screws).
D
E-P
ull the plastic tab to remove
the battery block and replace it.
E
614-07977-00_EN
Page 19
ENGLISH
5. Maintenance
5. Maintenance
Mounting the new battery module
Carry out the above instructions in reverse order.
pp To ensure safety and high performance, use only batteries supplied by EATON.
pp Take care to firmly press together the two parts of the connector during remounting.
5.3 Maintenance on a UPS equipped with the HotSwap MBP module
The HotSwap MBP module makes it
5PX
possible to service or even replace
the UPS without affecting the connected
loads (HotSwap function).
Maintenance
1. Set switch (55) to Bypass position.
The red LED on the HotSwap MBP
module goes ON, indicating that the
load is supplied directly with AC input
source power.
46
2. S
top the UPS by pressing the
button on the UPS control panel.
LED (53) "UPS ON - OK to switch"
HotSwap MBP
goes OFF, the UPS can now be
disconnected and replaced.
Return to normal operation
1. Check that the UPS is correctly
connected to the HotSwap MBP
51
52 53 54
55
56
57
58
module.
2. S
tart the UPS by pressing the
button on the UPS control panel.
LED (53) "UPS ON - OK to switch" on
the HotSwap MBP module goes ON
(otherwise, there is a connection error
between the HotSwap MBP module
and the UPS).
3. S
et switch (55) to Normal position.
The red LED on the HotSwap MBP
module goes OFF.
Page 20
614-07977-00_EN
6.1 Technical specifications
Filter
Transformer
"AVR"
Charger
Inverter
Battery
Output Power
AC Input power
l Rated input voltage
l Input voltage range
l input frequency range
Output on battery power
l Voltage
l Frequency
Battery
(sealed lead acid,
maintenance free)
l Standard
lA
dditional
modules possible
(up to 4 EBM)
Environnement
l Operating
temperature range
l Storage
temperature range
l
Relative humidity
5PX 1500i RT2U
1500 VA
1350 W
5PX 2000i RT2U
2000 VA
1800 W
5PX 2200i RT2U
2200 VA
1980 W
5PX 3000i RT2U
3000 VA
2700 W
Single phase 200-240 V
160 to 294 V (1)
47 to 70 Hz (50 Hz system), 56.5 to 70 Hz (60 Hz system)
5PX 3000i RT3U
3000 VA
2700 W
(2)
230 V (-10/+6 %) (3)
50/60 Hz ±0.1 Hz
4 x 12 V
7.2 Ah
4 x 12 V
9 Ah
5PX EBM 48V RT2U
(4)
6 x 12V
9Ah
5PX EBM 72 V
RT2U (5)
5PX EBM 72 V
RT3U (5)
0 to 40 °C
-15 to +50 °C
20 to 90 % (without condensation)
l Noise level
< 45 dBA
< 50 dBA
(1) The high and low thresholds can be adjusted using UPS settings (up to 150-294 V).
(2) Up to 40 Hz in low -sensitivity mode (programmable using UPS settings).
(3) Adjustable to 200/208/220/230/240 V (23 % derating at 200 V, and 10 % derating at 208 V on 2.2 kVA, 17 % derating at 200 V
on 3 kVA)
(4) 5PX EBM 48V RT2U: 2 strings, each 4 x 12 V / 9 Ah.
(5) 5PX EBM 72V RT2U and 5PX EBM 72V RT3U: 2 strings, each 6 x 12 V / 9 Ah.
When the appliance is used in EU area, use an external circuit breaker in front of line with rating 16 A,
250 V which is IEC/EN 60898-1 standard compliant;
When the appliance is used in America area, use an external circuit breaker in front of line with rating 20 A,
250 V.
This product is designed for IT power distribution system.
614-07977-00_EN
Page 21
ENGLISH
6. Appendices
6. Appendices
6.2 Glossary
Page 22
Backup time
Time during which the load can be supplied by the UPS operating on battery power.
Battery test
Internal UPS test to check battery status.
Cold start
The devices connected to the UPS can be started even if AC input power is not
available. The UPS operates on battery power alone.
Deep discharge
Battery discharge beyond the permissible limit, resulting in irreversible damage to
the battery.
FlexPDU
Module with UPS outlets for installation in a bay. There are different modules with
different types of outlets.
HotSwap MBP
UPS manual-bypass module for maintenance. There are different modules with
different types of outlets.
Load
Devices or equipment connected to the UPS output.
Low-battery
warning
This is a battery-voltage level indicating that battery power is low and that the user
must take action in light of the imminent break in the supply of power to the load.
Normal AC
input
The AC-power line supplying the UPS under normal conditions.
Percent load
Ratio of the power effectively drawn by the load to the maximum output of the UPS.
Personalisation
It is possible to modify certain UPS parameters set in the factory. Certain UPS
functions can also be modified by the software to better suit user needs.
Programmable
outlets
Controllable outlets for automatic load shedding, remote shutdown and sequential
restart (personalised using software).
UPS
Uninterruptible Power System.
UPS ON/OFF
controlled by
software
This function enables or disables initiation of UPS ON/OFF control sequences by
computer power-management software.
614-07977-00_EN
Download PDF
Similar pages