HP ProLiant ML350 Generation 4p Server Maintenance and Service

HP ProLiant ML350 Generation 4p Server
Maintenance and Service Guide
July 2006 (Second Edition)
Part Number 382586-002
© Copyright 2005, 2006 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP
shall not be liable for technical or editorial errors or omissions contained herein.
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Windows Server is a trademark of Microsoft Corporation.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
Linux is a U.S. registered trademark of Linus Torvalds.
July 2006 (Second Edition)
Part Number 382586-002
Audience assumptions
This guide is for an experienced service technician. HP assumes you are qualified in the servicing of
computer equipment and trained in recognizing hazards in products with hazardous energy levels and
are familiar with weight and stability precautions for rack installations.
Contents
Illustrated parts catalog ................................................................................................................. 5
Customer self repair................................................................................................................................... 5
Mechanical components............................................................................................................................. 6
System components ................................................................................................................................... 7
Removal and replacement procedures ........................................................................................... 10
Required tools......................................................................................................................................... 10
Safety considerations ............................................................................................................................... 10
Preventing electrostatic discharge .................................................................................................... 11
Symbols on equipment ................................................................................................................... 11
Rack warnings .............................................................................................................................. 12
Preparation procedures ............................................................................................................................ 12
Extending the server from the rack ................................................................................................... 13
Powering down the server .............................................................................................................. 13
Removing the server from the rack ................................................................................................... 14
Access panel .......................................................................................................................................... 14
Tower feet .............................................................................................................................................. 14
Front bezel (tower model)......................................................................................................................... 15
Rack rails ............................................................................................................................................... 15
Power supply blank ................................................................................................................................. 16
Hot-plug power supply ............................................................................................................................. 16
Hot-plug power supply backplane ............................................................................................................. 17
SCSI hard drive blanks ............................................................................................................................ 18
Hot-plug SCSI hard drives ........................................................................................................................ 18
Hot-plug SATA and SAS hard drives .......................................................................................................... 19
Redundant system fan .............................................................................................................................. 20
Expansion slot cover ................................................................................................................................ 21
Expansion board..................................................................................................................................... 22
Half-height media device.......................................................................................................................... 23
Tape drive.............................................................................................................................................. 24
Internal two-bay hot-plug SCSI drive cage................................................................................................... 25
Processor and heatsink............................................................................................................................. 26
PPM ...................................................................................................................................................... 30
DIMM .................................................................................................................................................... 31
Second serial port ................................................................................................................................... 32
Duplex SCSI backplane............................................................................................................................ 32
Battery ................................................................................................................................................... 33
System board ......................................................................................................................................... 34
Server serial number and product ID.......................................................................................................... 35
Diagnostic tools .......................................................................................................................... 36
Troubleshooting resources ........................................................................................................................ 36
Automatic Server Recovery ....................................................................................................................... 36
HP Systems Insight Manager ..................................................................................................................... 37
HP Instant Support Enterprise Edition.......................................................................................................... 37
Integrated Management Log ..................................................................................................................... 37
Option ROM Configuration for Arrays ....................................................................................................... 37
HP ProLiant Essentials Rapid Deployment Pack ............................................................................................ 38
ROM-Based Setup Utility .......................................................................................................................... 38
ROMPaq utility........................................................................................................................................ 38
Contents
3
System online ROM flash component utility ................................................................................................. 38
SmartStart software ................................................................................................................................. 39
HP Insight Diagnostics .................................................................................................................... 39
Server component identification.................................................................................................... 40
Front panel components ........................................................................................................................... 40
Front panel LEDs and buttons .................................................................................................................... 41
Rear panel components............................................................................................................................ 42
Rear panel LEDs ...................................................................................................................................... 43
System board components........................................................................................................................ 44
NMI jumper .................................................................................................................................. 45
System maintenance switch............................................................................................................. 45
System LEDs and internal health LED combinations....................................................................................... 46
System board LEDs .................................................................................................................................. 47
Hot-plug hard drive IDs ............................................................................................................................ 48
Hot-plug SCSI hard drive LEDs .................................................................................................................. 49
SATA or SAS hard drive LEDs ................................................................................................................... 50
Specifications ............................................................................................................................. 51
Tower server specifications ....................................................................................................................... 51
Rack server specifications ......................................................................................................................... 51
Environmental specifications ..................................................................................................................... 52
Hot-plug power supply calculations............................................................................................................ 52
DDR2 SDRAM DIMM specifications ........................................................................................................... 52
1.44-MB diskette drive specifications ......................................................................................................... 53
CD-ROM drive specifications .................................................................................................................... 53
Acronyms and abbreviations........................................................................................................ 55
Index......................................................................................................................................... 58
Contents
4
Illustrated parts catalog
In this section
Customer self repair ................................................................................................................................. 5
Mechanical components ........................................................................................................................... 6
System components .................................................................................................................................. 7
Customer self repair
What is customer self repair?
HP's customer self-repair program offers you the fastest service under either warranty or contract. It
enables HP to ship replacement parts directly to you so that you can replace them. Using this program,
you can replace parts at your own convenience.
A convenient, easy-to-use program:
•
An HP support specialist will diagnose and assess whether a replacement part is required to address
a system problem. The specialist will also determine whether you can replace the part.
•
Replacement parts are express-shipped. Most in-stock parts are shipped the very same day you
contact HP. You may be required to send the defective part back to HP, unless otherwise instructed.
•
Available for most HP products currently under warranty or contract. For information on the warranty
service, refer to the HP website
(http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html).
For more information about HP's customer self-repair program, contact your local service provider. For the
North American program, refer to the HP website (http://www.hp.com/go/selfrepair).
Customer replaceable parts are identified in the following tables.
Illustrated parts catalog 5
Mechanical components
Item
Description
Original spare
part number
Modified spare
part number
Customer self
repair (on page
5)
1
Access panel, tower
365058-001
—
Yes
2
Access panel, rack*
371714-001
—
Yes
3
Front bezel (tower model)
365064-001 ‡ 433940-001
See requirement
Yes
4
Rack bezel*
390545-001 ‡ 409684-001
See requirement
Yes
5
Removable media blank
231212-001
—
Yes
6
Hard drive blank
—
—
—
a) SCSI hard drive blank
319602-001
—
Yes
b) SATA hard drive blank*
392613-001
—
—
7
Hot-plug power supply blank
365059-001 ‡ 433942-001
See requirement
Yes
8
Return kit (tower model)*
339550-001
—
Yes
9
Return kit (rack model)*
290551-001
—
Yes
*Not shown
‡REQUIREMENT:
For Customers in the EU only.
The use of the Original Spare part is regulated by RoHS legislation§.
If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as
the replacement part in the EU.
Illustrated parts catalog 6
If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the
replacement part in the EU. In this case either the Original Spare or the Modified Spare may be shipped which will
not affect performance or functionality of the unit.
§Directive 2002/95/EC restricts the use of lead, mercury, cadmium, hexavalent chromium, PBBs and PBDEs in
electronic products.
System components
Item
Description
Original spare
part number
Modified spare
part number
Customer self
repair (on page
5)
System components
10
Fan assembly, 120-mm
367637-001
—
Yes
11
3.0-V lithium battery
234556-001
—
Yes
12
Heatsink
366866-001
—
Yes
13
Processor
—
—
—
a) Intel® Xeon™ 2.80-GHz, 1MB with 800MHz system bus
373580-005
—
Yes
b) Intel® Xeon™ 3.00-GHz, 1MB with 800MHz system bus*
366864-001
—
Yes
c) Intel® Xeon™ 3.00-GHz, 2MB with 800MHz system bus*
383035-001
—
Yes
d) Intel® Xeon™ 3.20-GHz, 2MB with 800MHz system bus*
383036-001
—
Yes
e) Intel® Xeon™ 3.40-GHz, 2MB with 800MHz system bus*
383037-001
—
Yes
Illustrated parts catalog 7
Item
Description
Original spare
part number
Modified spare
part number
Customer self
repair (on page
5)
14
Processor power module
347884-001
—
Yes
15
Hot-plug power supply, 725-W, 12-V
390394-001 ‡ 406413-001
See requirement
Yes
390546-001 ‡ 409682-001
See requirement
Yes
Boards
16
System board
17
SCSI hard drive cage with simplex backplane 366862-001
18
Power supply backplane
390548-001 ‡ 433943-001
See requirement
Yes
19
SATA/SAS hard drive cage*
390547-001 ‡ 409683-001
See requirement
Yes
Diskette drive, 3-mode, 1.44-MB with USB
372058-001 ‡ 433939-001
See requirement
Yes
CD-ROM drive, IDE, 48X
288894-001
—
Yes
—
Yes
Mass storage devices
20
21
Miscellaneous
22
Power switch
292236-001
—
Yes
23
Plastics kit*
250843-001
—
Yes
Miscellaneous signal cable kit*
163353-001
—
Yes
25
AC power cable, 3.66-m (12-ft)*
187335-001
—
Yes
26
SCSI cable*
367168-001
—
Yes
27
SCSI point-to-point cable*
292232-001
—
Yes
28
4-port SATA cable*
389950-001
—
Yes
DIMM
—
—
—
a) 512-MB DDR2 DIMM PC2-3200*
359241-001 ‡ 413384-001
See requirement
Yes
b) 1-GB DDR2 DIMM PC2-3200*
359242-001 ‡ 413385-001
See requirement
Yes
c) 2-GB DDR2 DIMM PC2-3200*
359243-001 ‡ 413386-001
See requirement
Yes
d) 2-GB DDR2 DIMM PC2-3200 (dual-rank)* 378021-001 ‡ 413387-001
See requirement
Yes
Cables
24
Memory
29
Options
30
Two-bay, SCSI hot-plug drive cage*
253761-001
—
Yes
31
Tower-to-rack conversion kit*
366861-001
—
Yes
32
Redundant system fan assembly
372213-001
—
Yes
33
Duplex SCSI backplane*
371722-001
—
Yes
34
Hard drives
—
—
—
a) 72-GB SCSI Ultra320, 10,000-rpm
404709-001
—
Yes
Illustrated parts catalog 8
Description
Original spare
part number
Modified spare
part number
Customer self
repair (on page
5)
b) 146-GB SCSI Ultra320, 10,000-rpm*
404708-001
—
Yes
c) 300-GB, SCSI Ultra320, 10,000-rpm*
404701-001
—
Yes
d) 80-GB SATA, 7,200-rpm*
399967-001
—
Yes
e) 160-GB SATA, 7,200-rpm*
399968-001
—
Yes
f) 250-GB SATA, 7,200-rpm*
399969-001
—
Yes
35
Second Serial Port*
391183-001 ‡ 409685-001
See requirement
Yes
36
Keyboard*
355630-001
—
Yes
37
Mouse*
344704-001
—
Yes
Item
*Not shown
‡REQUIREMENT:
For Customers in the EU only.
The use of the Original Spare part is regulated by RoHS legislation§.
If your unit contains a part that is labelled with the Modified Spare number, the Modified Spare must be ordered as
the replacement part in the EU.
If your unit contains a part that is labelled with the Original Spare number, please order the Original Spare as the
replacement part in the EU. In this case either the Original Spare or the Modified Spare may be shipped which will
not affect performance or functionality of the unit.
§Directive 2002/95/EC restricts the use of lead, mercury, cadmium, hexavalent chromium, PBBs and PBDEs in
electronic products.
Illustrated parts catalog 9
Removal and replacement procedures
In this section
Required tools........................................................................................................................................ 10
Safety considerations.............................................................................................................................. 10
Preparation procedures........................................................................................................................... 12
Access panel ......................................................................................................................................... 14
Tower feet ............................................................................................................................................. 14
Front bezel (tower model)........................................................................................................................ 15
Rack rails .............................................................................................................................................. 15
Power supply blank ................................................................................................................................ 16
Hot-plug power supply ............................................................................................................................ 16
Hot-plug power supply backplane ............................................................................................................ 17
SCSI hard drive blanks ........................................................................................................................... 18
Hot-plug SCSI hard drives ....................................................................................................................... 18
Hot-plug SATA and SAS hard drives......................................................................................................... 19
Redundant system fan ............................................................................................................................. 20
Expansion slot cover ............................................................................................................................... 21
Expansion board.................................................................................................................................... 22
Half-height media device......................................................................................................................... 23
Tape drive............................................................................................................................................. 24
Internal two-bay hot-plug SCSI drive cage ................................................................................................. 25
Processor and heatsink ........................................................................................................................... 26
PPM...................................................................................................................................................... 30
DIMM ................................................................................................................................................... 31
Second serial port .................................................................................................................................. 32
Duplex SCSI backplane .......................................................................................................................... 32
Battery .................................................................................................................................................. 33
System board......................................................................................................................................... 34
Server serial number and product ID......................................................................................................... 35
Required tools
You need the following items for some procedures:
•
T-15 Torx screwdriver
•
Flathead screwdriver
•
Diagnostics Utility
Safety considerations
Before performing service procedures, review all the safety information.
Removal and replacement procedures 10
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the
system or handling parts. A discharge of static electricity from a finger or other conductor may damage
system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the
device.
To prevent electrostatic damage:
•
Avoid hand contact by transporting and storing products in static-safe containers.
•
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
•
Place parts on a grounded surface before removing them from their containers.
•
Avoid touching pins, leads, or circuitry.
•
Always be properly grounded when touching a static-sensitive component or assembly.
Symbols on equipment
The following symbols may be placed on equipment to indicate the presence of potentially hazardous
conditions.
This symbol indicates the presence of hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified personnel.
WARNING: To reduce the risk of injury from electric shock hazards, do not open
this enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel.
This symbol indicates the presence of electric shock hazards. The area contains no
user or field serviceable parts. Do not open for any reason.
WARNING: To reduce the risk of injury from electric shock hazards, do not open
this enclosure.
This symbol on an RJ-45 receptacle indicates a network interface connection.
WARNING: To reduce the risk of electric shock, fire, or damage to the equipment,
do not plug telephone or telecommunications connectors into this receptacle.
This symbol indicates the presence of a hot surface or hot component. If this surface is
contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the surface to
cool before touching.
This symbol indicates that the component exceeds the recommended weight for one
individual to handle safely.
27.22 kg
60 lb
WARNING: To reduce the risk of personal injury or damage to the equipment,
observe local occupational health and safety requirements and guidelines for manual
material handling.
Removal and replacement procedures 11
These symbols, on power supplies or systems, indicate that the equipment is supplied
by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power
cords to completely disconnect power from the system.
Rack warnings
WARNING: To reduce the risk of personal injury or damage to the equipment, be sure
that:
• The leveling jacks are extended to the floor.
• The full weight of the rack rests on the leveling jacks.
• The stabilizing feet are attached to the rack if it is a single-rack installation.
• The racks are coupled together in multiple-rack installations.
• Only one component is extended at a time. A rack may become unstable if more than
one component is extended for any reason.
WARNING: To reduce the risk of personal injury or equipment damage when unloading
a rack:
• At least two people are needed to safely unload the rack from the pallet. An empty
42U rack can weigh as much as 115 kg (253 lb), can stand more than 2.1 m (7 ft)
tall, and may become unstable when being moved on its casters.
• Never stand in front of the rack when it is rolling down the ramp from the pallet.
Always handle the rack from both sides.
WARNING: To reduce the risk of personal injury or damage to the equipment,
adequately stabilize the rack before extending a component outside the rack. Extend
only one component at a time. A rack may become unstable if more than one component
is extended.
WARNING: When installing a server in a telco rack, be sure that the rack frame is
adequately secured to the top and bottom of the building structure.
Preparation procedures
To access some components and perform certain service procedures, you must perform one or more of the
following procedures:
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
If you are performing service procedures in a Compaq branded rack, telco rack, or third-party rack
cabinet, you can use the locking feature of the rack rails to support the server and gain access to
internal components.
For more information about telco rack solutions, refer to the RackSolutions.com website
(http://www.racksolutions.com/hp).
•
Power down the server ("Powering down the server" on page 13).
If you must remove a server from a rack or a non-hot-plug component from a server, power down the
server.
•
Remove the server from the rack ("Removing the server from the rack" on page 14).
If the rack environment, cabling configuration, or the server location in the rack creates awkward
conditions, remove the server from the rack.
Removal and replacement procedures 12
Extending the server from the rack
1.
Loosen the thumbscrews that secure the server faceplate to the front of the rack.
IMPORTANT: If the server is installed in a telco rack, remove the server from the rack to access internal
components.
2.
Extend the server on the rack rails until the server rail-release latches engage.
WARNING: To reduce the risk of personal injury or equipment damage, be sure that the
rack is adequately stabilized before extending a component from the rack.
WARNING: To reduce the risk of personal injury, be careful when pressing the server
rail-release latches and sliding the server into the rack. The sliding rails could pinch your
fingers.
3.
After performing the installation or maintenance procedure, slide the server back into the rack:
a. Press the server rail-release latches and slide the server fully into rack.
b. Secure the server by tightening the thumbscrews.
Powering down the server
WARNING: To reduce the risk of personal injury, electric shock, or damage to the
equipment, remove the power cord to remove power from the server. The front panel
Power On/Standby button does not completely shut off system power. Portions of the
power supply and some internal circuitry remain active until AC power is removed.
IMPORTANT: If installing a hot-plug device, it is not necessary to power down the server.
1.
Shut down the operating system as directed by the operating system documentation.
2.
Press the Power On/Standby button to place the server in standby mode. When the server activates
standby power mode, the system power LED changes to amber.
3.
Disconnect the power cords.
The system is now without power.
CAUTION: Due to the high capacitance in the power supply, always wait 30 seconds after disconnecting
the power cord before removing the access panel.
Removal and replacement procedures 13
Removing the server from the rack
To remove the server from an HP, telco, or third-party rack:
1.
Power down the server ("Powering down the server" on page 13).
2.
Loosen the front panel thumbscrews that secure the server faceplate to the front of the rack.
3.
Disconnect the cabling and remove the server from the rack. Reverse the server installation steps in
the documentation that ships with the rack-mounting option.
4.
Place the server on a sturdy, level surface.
Access panel
CAUTION: Due to the high capacitance in the power supply, always wait 30 seconds after disconnecting
the power cord before removing the access panel.
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
a. Remove the server from the rack, if applicable ("Removing the server from the rack" on page
14).
b. Remove the tower front bezel, if applicable ("Front bezel (tower model)" on page 15).
3.
Loosen the two thumbscrews on the front panel of the server near the access panel.
4.
Slide the access panel back about 1.5 cm (0.5 in).
5.
Lift and remove the access panel.
NOTE: Turn the access panel over to locate the hood labels. These labels provide information on installing
various options, flexible memory configurations, LED status indicators, and switch settings.
To replace the component, reverse the removal procedure.
Tower feet
Remove the feet.
Removal and replacement procedures 14
To replace the component, reverse the removal procedure.
Front bezel (tower model)
This server has a removable front bezel that must be unlocked and opened before accessing the hard
drive cage or removing the access panel. The door should be kept closed during normal server
operations.
Use the key provided with the server to unlock the bezel with a clockwise turn.
If necessary, remove the front bezel.
Rack rails
NOTE: This procedure applies to rack servers only.
To remove the component:
1.
Use a flat-head screwdriver to lift the spring tab.
Removal and replacement procedures 15
2.
Slide the rail forward and remove it from the server.
3.
Repeat steps 1 and 2 to remove other rail.
To replace the component, reverse the removal procedure.
Power supply blank
Loosen the thumbscrew that secures the redundant power supply blank, and then pull the blank from the
back of the server.
Hot-plug power supply
WARNING: To reduce the risk of electric shock, do not disassemble the power supply or
attempt to repair it. Replace it only with the specified spare part.
CAUTION: Do not attempt to remove and replace a power supply as a hot-plug procedure unless both
bays are populated with power supplies.
To remove the component:
1.
Remove the power cord from the unit to be removed.
Removal and replacement procedures 16
2.
Push down on the power supply release latch, and remove the power supply from the server.
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays
are populated with either a component or a blank.
To replace the component, reverse the removal procedure.
Hot-plug power supply backplane
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Remove the power supplies from the server ("Hot-plug power supply" on page 16).
3.
Remove the access panel ("Access panel" on page 14).
4.
Disconnect the cables from the components connected to the power supply backplane.
5.
Remove the power supply backplane.
To replace the component, reverse the removal procedure.
Removal and replacement procedures 17
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays
are populated with either a component or a blank.
SCSI hard drive blanks
To remove the component:
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays
are populated with either a component or a blank.
NOTE: Depending on model purchased, the server may look slightly different than shown.
To replace the component, reverse the removal procedure.
Hot-plug SCSI hard drives
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays
are populated with either a component or a blank.
To remove the component:
1.
Open the front bezel ("Front bezel (tower model)" on page 15).
2.
Determine the status of the hard drive from the hot-plug hard drive LEDs ("Hot-plug SCSI hard drive
LEDs" on page 49).
3.
Back up all server data on the hard drive.
Removal and replacement procedures 18
4.
Remove the hard drive.
To replace the component, reverse the procedure.
Hot-plug SATA and SAS hard drives
Hot-plug SATA and hot-plug SAS hard drives can be used interchangeably when a SAS controller is
installed. Before installing a SAS hard drive, you must install a SAS controller. A SATA controller is
embedded for use with SATA drives only.
To remove the component:
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays
are populated with either a component or a blank.
1.
Open the front bezel ("Front bezel (tower model)" on page 15).
2.
Determine the status of the hard drive:
a. when using the embedded SATA controller, observe the OS logs or the status in POST
b. when using an optional SATA/SAS controller, observe the hot-plug hard drive LEDs ("SATA or
SAS hard drive LEDs" on page 50)
3.
Back up all server data on the hard drive.
4.
Disconnect the cables from the hot-plug SATA/SAS drive cage.
Removal and replacement procedures 19
5.
Remove the hard drive.
To replace the component:
1.
Remove the existing hard drive blank or hard drive from the drive bay.
2.
Install the hard drive.
3.
Determine the status of the hard drive from the hot-plug hard drive LEDs ("Hot-plug SCSI hard drive
LEDs" on page 49).
4.
Resume normal server operations.
Redundant system fan
CAUTION: The redundant system fan is not hot-pluggable.
To remove the redundant system fan:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
Removal and replacement procedures 20
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Disconnect the redundant system fan cable from the redundant system fan connector on the system
board.
5.
Remove the fan.
To replace the component, reverse the removal procedure.
Expansion slot cover
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
3.
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
Remove the access panel ("Access panel" on page 14).
Removal and replacement procedures 21
4.
Remove the expansion slot cover.
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all PCI slots
have either an expansion slot cover or an expansion board installed.
To replace the component, reverse the removal procedure.
Expansion board
CAUTION: To prevent damage to the server or expansion boards, power down the server and remove all
AC power cords before removing or installing the expansion boards.
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
3.
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
Remove the access panel ("Access panel" on page 14).
Removal and replacement procedures 22
4.
Remove the expansion board retainer.
5.
Disconnect any internal or external cables from the expansion board.
6.
Remove the expansion board.
7.
Reinstall the expansion board retainer, then tighten the thumbscrew.
To replace the component, reverse the removal procedure.
Half-height media device
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Disconnect the cables from the rear of the media device.
Removal and replacement procedures 23
5.
Push up on the release lever and push the drive partially out through the front of the server.
6.
Remove the media device.
To replace the component, reverse the removal procedure.
Tape drive
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Disconnect the data and power cables from the rear of the tape drive.
5.
Push up on the release lever and push the drive partially out through the front of the server.
6.
Remove the tape drive.
Removal and replacement procedures 24
To replace the component, reverse the removal procedure.
IMPORTANT: HP recommends installing the tape drive on a separate SCSI cable to avoid a decrease in
performance on other SCSI devices.
Internal two-bay hot-plug SCSI drive cage
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Access the removable media cage.
5.
Disconnect the SCSI and power cables.
6.
Remove the drive cage from the chassis.
Removal and replacement procedures 25
To replace the component, reverse the removal procedure.
IMPORTANT: Be sure that the unit identification numbers (0 and 1) appear on the right side of the drive
cage front panel.
Refer to the HP Internal Two-Bay Hot-Plug SCSI Drive Cage Installation Instructions for additional
information.
Processor and heatsink
IMPORTANT: If upgrading processor speed, update the system ROM before installing the processor.
IMPORTANT: PPM 2 must be installed when processor 2 is installed. The system fails to boot if the PPM is
missing.
To remove a processor and heatsink:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Disconnect the heatsink fan cable from the heatsink connectors on the system board.
5.
Open the heatsink retaining levers.
Removal and replacement procedures 26
6.
Remove the heatsink.
7.
Open the processor locking lever and remove the processor.
To replace the processor and heatsink:
1.
Open the processor locking lever, if necessary.
2.
Install the processor and close the processor locking lever.
Removal and replacement procedures 27
CAUTION: Forcing the processor locking lever could lead to hardware damage.
IMPORTANT: Do not remove the thermal tape from the bottom of the heatsink. Removing the tape will
affect the thermal solution and prevent the system from working properly.
Removal and replacement procedures 28
3.
Install the heatsink.
4.
Close the processor retaining brackets.
Removal and replacement procedures 29
5.
Connect the heatsink fan cable to the connector on the system board.
Item
Description
1
Processor 1 heatsink fan connector
2
Processor 2 heatsink fan connector
6.
Install the access panel.
PPM
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Open the latches on the PPM slot.
5.
Remove the PPM for processor 2 (if a second processor is installed).
Removal and replacement procedures 30
NOTE: PPM 1 is embedded in the system board.
NOTE: The appearance of compatible PPMs may vary.
To replace the component, reverse the removal procedure.
DIMM
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Open the DIMM slot latches.
5.
Remove the DIMM.
To replace the component, reverse the removal procedure.
Removal and replacement procedures 31
Second serial port
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Open the retention clip securing the second serial port.
5.
Remove the serial port cable from the serial port header on the system board.
6.
Remove the second serial port option.
To replace the component, reverse the removal procedure.
Duplex SCSI backplane
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
3.
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
Remove the access panel ("Access panel" on page 14).
Removal and replacement procedures 32
4.
Remove the SCSI cable from the duplex SCSI backplane and from either the array controller or the
system board.
5.
Remove the duplex SCSI backplane.
To replace the component, reverse the removal procedure.
Battery
If the server no longer automatically displays the correct date and time, you may need to replace the
battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years.
WARNING: The computer contains an internal lithium manganese dioxide, a vanadium
pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack
is not properly handled. To reduce the risk of personal injury:
Removal and replacement procedures 33
•
•
•
•
Do not attempt to recharge the battery.
Do not expose the battery to temperatures higher than 60°C (140°F).
Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or
water.
Replace only with the spare designated for this product.
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Remove the battery.
IMPORTANT: Replacing the system board battery resets the system ROM to its default configuration. After
replacing the battery, reconfigure the system through RBSU.
To replace the component, reverse the removal procedure.
For more information about battery replacement or proper disposal, contact an authorized reseller or an
authorized service provider.
System board
To remove the component:
1.
Power down the server ("Powering down the server" on page 13).
2.
Do one of the following:
•
Unlock and remove the bezel ("Front bezel (tower model)" on page 15).
•
Extend the server from the rack ("Extending the server from the rack" on page 13).
3.
Remove the access panel ("Access panel" on page 14).
4.
Remove the system fans ("Redundant system fan" on page 20).
5.
Remove the processors and heatsinks ("Processor and heatsink" on page 26).
6.
Remove all DIMMs ("DIMM" on page 31).
Removal and replacement procedures 34
7.
Remove all expansion boards ("Expansion board" on page 22).
8.
Remove the PPM for processor 2 ("PPM" on page 30).
9.
Disconnect all cables connected to the system board.
10. Remove the four system board screws, and remove the system board.
To replace the component, reverse the removal procedure.
Server serial number and product ID
After you replace the system board, you must re-enter the server serial number and the product ID.
1.
During the server startup sequence, press the F9 key to access RBSU.
2.
Select the System Options menu.
3.
Select Serial Number. The following warning is displayed:
WARNING! WARNING! WARNING! The serial number is loaded into the system
during the manufacturing process and should NOT be modified. This option
should only be used by qualified service personnel. This value should
always match the serial number sticker located on the chassis.
4.
Press the Enter key to clear the warning.
5.
Enter the serial number and press the Enter key.
6.
Select Product ID.
7.
Enter the product ID and press the Enter key.
8.
Press the Esc key to close the menu.
9.
Press the Esc key to exit RBSU.
Press the F10 key to confirm exiting RBSU. The server will automatically reboot.
Removal and replacement procedures 35
Diagnostic tools
In this section
Troubleshooting resources ....................................................................................................................... 36
Automatic Server Recovery ...................................................................................................................... 36
HP Systems Insight Manager.................................................................................................................... 37
HP Instant Support Enterprise Edition ........................................................................................................ 37
Integrated Management Log .................................................................................................................... 37
Option ROM Configuration for Arrays ...................................................................................................... 37
HP ProLiant Essentials Rapid Deployment Pack........................................................................................... 38
ROM-Based Setup Utility ......................................................................................................................... 38
ROMPaq utility....................................................................................................................................... 38
System online ROM flash component utility................................................................................................ 38
SmartStart software ................................................................................................................................ 39
Troubleshooting resources
The HP ProLiant Servers Troubleshooting Guide provides simple procedures for resolving common
problems as well as a comprehensive course of action for fault isolation and identification, error message
interpretation, issue resolution, and software maintenance.
To obtain the guide, refer to any of the following sources and then select the HP ProLiant Servers
Troubleshooting Guide:
•
The server-specific Documentation CD
•
The Business Support Center on the HP website (http://www.hp.com/support). Navigate to the
server technical support page. Under self-help resources, select ProLiant Troubleshooting
Guide.
•
The Technical Documentation website (http://www.docs.hp.com). Select Enterprise Servers,
Workstations and Systems Hardware, and then the appropriate server.
Automatic Server Recovery
ASR is a feature that causes the system to restart when a catastrophic operating system error occurs, such
as a blue screen, ABEND, or panic. A system fail-safe timer, the ASR timer, starts when the System
Management driver, also known as the Health Driver, is loaded. When the operating system is
functioning properly, the system periodically resets the timer. However, when the operating system fails,
the timer expires and restarts the server.
ASR increases server availability by restarting the server within a specified time after a system hang or
shutdown. At the same time, the HP SIM console notifies you by sending a message to a designated
pager number that ASR has restarted the system. You can disable ASR from the HP SIM console or
through RBSU.
Diagnostic tools 36
HP Systems Insight Manager
HP SIM is a web-based application that allows system administrators to accomplish normal administrative
tasks from any remote location, using a web browser. HP SIM provides device management capabilities
that consolidate and integrate management data from HP and third-party devices.
IMPORTANT: You must install and use HP SIM to benefit from the Pre-Failure Warranty for processors,
SAS and SCSI hard drives, and memory modules.
For additional information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack or
the HP SIM website (http://www.hp.com/go/hpsim).
HP Instant Support Enterprise Edition
ISEE is a proactive remote monitoring and diagnostic tool to help manage your systems and devices, a
feature of HP support. ISEE provides continuous hardware event monitoring and automated notification to
identify and prevent potential critical problems. Through remote diagnostic scripts and vital system
configuration information collected about your systems, ISEE enables fast restoration of your systems.
Install ISEE on your systems to help mitigate risk and prevent potential critical problems.
For more information on ISEE, refer to the HP website
(http://www.hp.com/hps/hardware/hw_enterprise.html).
To download HP ISEE, visit the HP website (http://www.hp.com/hps/hardware/hw_downloads.html).
For installation information, refer to the HP ISEE Client Installation and Upgrade Guide
(ftp://ftp.hp.com/pub/services/hardware/info/isee_client.pdf).
Integrated Management Log
The IML records hundreds of events and stores them in an easy-to-view form. The IML timestamps each
event with 1-minute granularity.
You can view recorded events in the IML in several ways, including the following:
•
From within HP SIM ("HP Systems Insight Manager" on page 37)
•
From within Survey Utility
•
From within operating system-specific IML viewers
•
For NetWare: IML Viewer
•
For Windows®: IML Viewer
•
For Linux: IML Viewer Application
•
From within the RILOE user interface
•
From within HP Insight Diagnostics (on page 39)
For more information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack.
Option ROM Configuration for Arrays
Before installing an operating system, you can use the ORCA utility to create the first logical drive, assign
RAID levels, and establish online spare configurations.
The utility also provides support for the following functions:
•
Reconfiguring one or more logical drives
Diagnostic tools 37
•
Viewing the current logical drive configuration
•
Deleting a logical drive configuration
•
Setting the controller to be the boot controller
If you do not use the utility, ORCA will default to the standard configuration.
For more information regarding array controller configuration, refer to the controller user guide.
For more information regarding the default configurations that ORCA uses, refer to the HP ROM-Based
Setup Utility User Guide on the Documentation CD.
HP ProLiant Essentials Rapid Deployment Pack
The RDP software is the preferred method for rapid, high-volume server deployments. The RDP software
integrates two powerful products: Altiris Deployment Solution and the HP ProLiant Integration Module.
The intuitive graphical user interface of the Altiris Deployment Solution console provides simplified pointand-click and drag-and-drop operations that enable you to deploy target servers, including server blades,
remotely. It enables you to perform imaging or scripting functions and maintain software images.
For more information about the RDP, refer to the HP ProLiant Essentials Rapid Deployment Pack CD or
refer to the HP website (http://www.hp.com/servers/rdp).
ROM-Based Setup Utility
RBSU, an embedded configuration utility, performs a wide range of configuration activities that may
include:
•
Configuring system devices and installed options
•
Displaying system information
•
Selecting the primary boot controller
For more information on RBSU, refer to the HP ROM-Based Setup Utility User Guide on the Documentation
CD or the HP website (http://www.hp.com/servers/smartstart).
ROMPaq utility
Flash ROM enables you to upgrade the firmware (BIOS) with system or option ROMPaq utilities. To
upgrade the BIOS, insert a ROMPaq diskette into the diskette drive and boot the system.
The ROMPaq utility checks the system and provides a choice (if more than one exists) of available ROM
revisions. This procedure is the same for both system and option ROMPaq utilities.
For more information about the ROMPaq utility, refer to the HP website
(http://www.hp.com/servers/manage).
System online ROM flash component utility
The Online ROM Flash Component Utility enables system administrators to efficiently upgrade system or
controller ROM images across a wide range of servers and array controllers. This tool has the following
features:
•
Works offline and online
•
Supports Microsoft®, Windows® 2000, Windows Server™ 2003, Novell Netware, and Linux
operating systems
Diagnostic tools 38
IMPORTANT: This utility supports operating systems that may not be supported by the server. For
operating systems supported by the server, refer to the HP website (http://www.hp.com/go/supportos).
•
Integrates with other software maintenance, deployment, and operating system tools
•
Automatically checks for hardware, firmware, and operating system dependencies, and installs only
the correct ROM upgrades required by each target server
To download the tool and for more information, refer to the HP website
(http://h18000.www1.hp.com/support/files/index.html).
SmartStart software
SmartStart is a collection of software that optimizes single-server setup, providing a simple and consistent
way to deploy server configuration. SmartStart has been tested on many ProLiant server products,
resulting in proven, reliable configurations.
SmartStart assists the deployment process by performing a wide range of configuration activities,
including:
•
Configuring hardware using embedded configuration utilities, such as RBSU and ORCA
•
Preparing the system for installing "off-the-shelf" versions of leading operating system software
•
Installing optimized server drivers, management agents, and utilities automatically with every
assisted installation
•
Testing server hardware using the Insight Diagnostics Utility ("HP Insight Diagnostics" on page 39)
•
Installing software drivers directly from the CD. With systems that have internet connection, the
SmartStart Autorun Menu provides access to a complete list of ProLiant system software.
•
Enabling access to the Array Configuration Utility, Array Diagnostic Utility, and Erase Utility
SmartStart is included in the HP ProLiant Essentials Foundation Pack. For more information about
SmartStart software, refer to the HP ProLiant Essentials Foundation Pack or the HP website
(http://www.hp.com/servers/smartstart).
HP Insight Diagnostics
HP Insight Diagnostics is a proactive server management tool, available in both offline and online
versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify
server installations, troubleshoot problems, and perform repair validation.
HP Insight Diagnostics Offline Edition performs various in-depth system and component testing while the
OS is not running. To run this utility, launch the SmartStart CD.
HP Insight Diagnostics Online Edition is a web-based application that captures system configuration and
other related data needed for effective server management. Available in Microsoft® Windows® and
Linux versions, the utility helps to ensure proper system operation.
For more information or to download the utility, refer to the HP website
(http://www.hp.com/servers/diags).
Diagnostic tools 39
Server component identification
In this section
Front panel components .......................................................................................................................... 40
Front panel LEDs and buttons ................................................................................................................... 41
Rear panel components........................................................................................................................... 42
Rear panel LEDs ..................................................................................................................................... 43
System board components....................................................................................................................... 44
System LEDs and internal health LED combinations ..................................................................................... 46
System board LEDs ................................................................................................................................. 47
Hot-plug hard drive IDs ........................................................................................................................... 48
Hot-plug SCSI hard drive LEDs ................................................................................................................. 49
SATA or SAS hard drive LEDs .................................................................................................................. 50
Front panel components
Item
Description
1
Removable media bays (4)
2
Hot-plug hard drive bays (6)
3
Power On/Standby button
4
UID button
5
USB connector
6
Diskette drive
7
CD-ROM drive
Server component identification 40
Front panel LEDs and buttons
Item
Description
Status
1
UID LED
Blue = Activated
Flashing = System remotely managed
Off = Deactivated
2
Internal health LED
Green = Normal
Amber = System degraded. Refer to system board LEDs (on page
47) to identify component in degraded state.
Red = System critical. Refer to system board LEDs (on page 47) to
identify component in critical state.
Off = Normal (when in standby mode)
3
External health LED
(power supply)
Green = Power supply OK
Amber = Redundancy failure
Red = Critical power failure
4
NIC activity LED
Green = Network link
Flashing = Network link and activity
Off = No link to network. If power is off, view the rear panel
RJ­45 LEDs for status.
5
System power LED
On = Power
Amber = System off and power available
Off = No power
6
Power On/Standby button
—
7
UID button
—
Server component identification 41
Rear panel components
Item
Description
1
Power cord connector
2
Optional hot-plug redundant power supply bay
3
SCSI connector knockouts
4
PCI Express slot 1 (x4, half-length)
5
PCI Express slot 2 (x8 (full-length)
6
PCI-X slot 3 (bus 9, 64-bit/100-MHz)
7
PCI-X slot 4 (bus 9, 64-bit/100-MHz)
8
PCI-X slot 5 (bus 6, 64-bit/133-MHz)
9
PCI-X slot 6 (bus 2, 64-bit/66-MHz)
10
iLO Management connector
11
RJ-45 Ethernet connector
12
USB 2.0 connector
13
Video connector
14
Parallel connector
15
Serial connector
16
Keyboard connector
17
Mouse connector
Server component identification 42
Rear panel LEDs
Item
LED
Status
1
Power supply LED
Green = Power supply is on and functioning
Off = No power or inadequate power supply
2
UID LED
Blue = Activated
Flashing = Remote inquiry
Off = Deactivated
3
10/100/1000
On = Link
NIC link LED
Flashing = Activity
Off = No link
4
5
10/100/1000
On = Standby
NIC standby LED
Off = Activity
iLO NIC Activity LED
On = Link
Flashing = Activity
Off = No link
6
iLO NIC standby LED
On = Standby
Off = Activity
Server component identification 43
System board components
NOTE: PPM 1 is embedded in the system board.
Item
Description
1
Power supply connectors
2
Processor 1 heatsink fan connector
3
Processor socket 1
4
Processor socket 2
5
Diskette drive connector
6
Primary IDE connector (ATAPI devices)
7
Processor 2 heatsink fan connector
8
Power button/LED connector
9
SATA 1 connector
10
SATA 2 connector
11
Primary SCSI connector
12
Secondary SCSI connector
13
PPM 2 slot
14
RILOE II connector (30-pin)
15
Serial port connector
16
PCI-X slot 6 (bus 2, 64-bit/66-MHz)
17
PCI-X slot 5 (bus 6, 64-bit/133-MHz)
18
PCI-X slot 4 (bus 9, 64-bit/100-MHz)
19
PCI-X slot 3 (bus 9, 64-bit/100-MHz)
20
System maintenance switch
21
System battery
22
PCI Express slot 2 (x8, full-length)
23
PCI Express slot 1 (x4, half-length)
24
NMI jumper
Server component identification 44
Item
Description
25
Redundant fan connector
26
System fan connector
27
DIMM slot 6 (bank C)
28
DIMM slot 5 (bank C)
29
DIMM slot 4 (bank B)
30
DIMM slot 3 (bank B)
31
DIMM slot 2 (bank A)
32
DIMM slot 1 (bank A)
NMI jumper
The NMI jumper allows administrators to perform a memory dump before performing a hard reset. Crash
dump analysis is an essential part of eliminating reliability problems, such as hangs or crashes in
operating systems, device drivers, and applications. Many crashes freeze a system, requiring you to do a
hard reset. Resetting the system erases any information that would support root cause analysis.
Systems running Microsoft® Windows® operating systems experience a blue screen trap when the
operating system crashes. When this happens, Microsoft® recommends that system administrators
perform an NMI event by pressing a dump switch. The NMI event enables a hung system to become
responsive again.
System maintenance switch
Position
Default
Function
S1
RILOE
security
Off = RILOE security is enabled
Off
Off = System configuration can be
changed.
S2
On = RILOE security is disabled
On = System configuration is
locked.
S3
Off
Reserved
S4
Off
Reserved
S5
Off
Off = Power-on password is
enabled.
On = Power-on password is
disabled.
S6
Off
Off = No function
On = Clear NVRAM
S7
—
Reserved
S8
—
Reserved
When the system maintenance switch position 6 is set to the On position, the system is prepared to erase
all system configuration settings from both CMOS and NVRAM.
CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. Be sure to properly
configure the server or data loss could occur.
Server component identification 45
System LEDs and internal health LED combinations
When the internal health LED on the front panel illuminates either amber or red, the server is experiencing
a health event. Combinations of illuminated system LEDs and the internal health LED indicate system
status.
The front panel health LEDs indicate only the current hardware status. In some situations, HP SIM may
report server status differently than the health LEDs because the software tracks more system attributes.
System LED and Color
Internal Health
LED Color
Status
Processor failure,
socket X (amber)
Red
One or more of the following conditions may exist:
•
Processor in socket X has failed.
•
Processor in socket X failed over to the second processor.
•
Processor X is not installed in the socket.
•
Processor X is not supported.
•
Processor heatsink is not attached properly.
Amber
Processor in socket X is in a pre-failure condition.
Processor failure, both
sockets (amber)
Red
Processor types are mismatched.
PPM failure (amber)
Red
•
PPM has failed.
•
PPM is not installed, but the corresponding processor is
installed.
•
DIMM in slot X has failed.
•
DIMM in slot X is an unsupported type, and no valid
memory exists in another bank.
•
DIMM in slot X has reached single-bit correctable error
threshold.
•
DIMM in slot X is in a pre-failure condition.
•
DIMM in slot X is an unsupported type, but valid memory
exists in another bank.
•
The Health Driver has detected a cautionary temperature
level.
•
The server has detected a hardware critical temperature
level.
DIMM failure, slot X
(amber)
Red
Amber
Overtemperature
(amber)
Fan (amber)
Red
Red
The minimum fan requirements are not being met. Fan has
failed.
Amber
A fan has failed but still meets the minimum fan requirements
(with redundant system fan option only).
Server component identification 46
System board LEDs
Item
LED description
Status
1
AC power
Off = No AC power or failed power supply
Green = Power supply is on and functioning
2
3
Processor 1 fan
status
Off = Processor fan is functioning
Processor 1 status
Off = Processor 1 functioning
Amber = Fan is not installed or has failed
Amber = Processor 1 failed
4
5
6
PPM 1 (embedded)
status
Off = PPM 1 is functioning
Processor 2 fan
status
Off = Processor fan is functioning
Processor 2 status
Off = Processor 1 is functioning
Amber = PPM 1 has failed
Amber = Fan is not installed or has failed
Amber = Processor 1 has failed
7
PPM 2 status
Off = PPM 2 is functioning
Amber = PPM 2 has failed
8
9
Temperature
threshold
Off = Normal
Memory status
Off = Normal
Amber = System temperature threshold has
been exceeded
Amber = Memory has failed or configuration
problem has occurred
10
11
Online spare
memory failover
Off = Normal
Redundant fan status
Off = Fan is functioning
Amber = Online spare memory is in use
because of memory failover
Amber = Redundant fan has failed
12
Rear fan status
Off = Processor fan is functioning
Amber = Fan is not installed or has failed
Server component identification 47
Item
LED description
Status
13
DIMM 6 status
Off = DIMM 6 is functioning
Amber = DIMM 6 has failed
14
DIMM 5 status
Off = DIMM 5 is functioning
Amber = DIMM 5 has failed
15
DIMM 4 status
Off = DIMM 4 is functioning
16
DIMM 3 status
Off = DIMM 3 is functioning
Amber = DIMM 4 has failed
Amber = DIMM 3 has failed
17
DIMM 2 status
Off = DIMM 2 is functioning
Amber = DIMM 2 has failed
18
DIMM 1 status
Off = DIMM 1 is functioning
Amber = DIMM 1 has failed
Hot-plug hard drive IDs
SCSI models of the HP ProLiant ML350 Generation 4p Server support single- or dual-channel SCSI hard
drive configurations. The single-channel configuration (simplex) supports up to six SCSI hard drives on
one channel. The dual-channel configuration (duplex) supports two SCSI hard drives on one channel
(SCSI IDs 4 and 5) and up to four SCSI hard drives on the other channel (SCSI IDs 0 through 3) with the
duplex option.
The SCSI IDs for both simplex and duplex configurations are illustrated. Always populate hard drive bays
starting with the lowest SCSI ID.
SATA models of the HP ProLiant ML350 Generation 4p Server support up to six hard drives. The
embedded SATA controller supports drives in bays 1 and 2 (SATA IDs 1 and 2). An optional controller is
required to support drives in bays 3 through 6 (SATA IDs 3 through 6). The hot-plug SATA drive cage also
supports 8.89-cm (3.5-in) SAS hot-plug hard drives. An optional SAS controller is required to support SAS
drives.
Item
Description
1
Hot-plug SCSI hard drive cage
Server component identification 48
Item
Description
2
Hot-plug SATA hard drive cage (SAS-enabled)
Hot-plug SCSI hard drive LEDs
Item
LED description
Status
1
Activity status
On = Drive activity
Flashing = High activity on the drive or drive
is being configured as part of an array.
Off = No drive activity
2
Online status
On = Drive is part of an array and is
currently working.
Flashing = Drive is actively online.
Off = Drive is offline.
3
Fault status
On = Drive failure
Flashing = Fault-process activity
Off = No fault-process activity
Server component identification 49
SATA or SAS hard drive LEDs
Item
LED description
Status
1
Online/Activity status
Green = Drive activity
Flashing green = High activity on the
drive or drive is being configured as part
of an array
Off = No drive activity
2
Fault/UID status
Amber = Drive failure
Flashing amber = Fault-process activity
Blue = Unit identification is active
Off = No fault-process activity
Server component identification 50
Specifications
In this section
Tower server specifications...................................................................................................................... 51
Rack server specifications........................................................................................................................ 51
Environmental specifications .................................................................................................................... 52
Hot-plug power supply calculations .......................................................................................................... 52
DDR2 SDRAM DIMM specifications.......................................................................................................... 52
1.44-MB diskette drive specifications........................................................................................................ 53
CD-ROM drive specifications ................................................................................................................... 53
Tower server specifications
Specification
Value
Dimensions
Height
44.45 cm (17.50 in)
Depth (with bezel)
64 cm (25.2 in)
Width
22 cm (8.66 in)
Weight (no drives installed)
27.22 kg (60 lb)
Models with a redundant power supply
Input requirements
Rated input voltage
100 VAC to 240 VAC
Rated input frequency
47 Hz to 63 Hz
Rated input current
10 A (110 V) to 5 A (220 V)
Rated input power
893 W
BTUs per hour
3049
Power supply output
Rated steady-state power
700 W
Maximum peak power
725 W
Rack server specifications
Specification
Value
Dimensions
Height
21.87 cm (8.61 in)
Depth (with bezel)
50.17 cm (19.75 in)
Width (with bezel)
48.26 cm (19 in)
Weight (no drives installed)
27.24 kg (60 lb)
Specifications
51
Models with a redundant power supply
Input requirements
Rated input voltage
100 VAC to 240 VAC
Rated input frequency
47 Hz to 63 Hz
Rated input current
10 A (110 V) to 5 A (220 V)
Rated input power
893 W
BTUs per hour
3049
Power supply output
Rated steady-state power
725 W
Maximum peak power
725 W
Environmental specifications
Specification
Value
Temperature range*
Operating
10°C to 35°C (50°F to 95°F)
Shipping
-40°C to 70°C (-40°F to 158°F)
Maximum wet bulb temperature
28°C (82.4°F)
Relative humidity
(noncondensing)**
Operating
10% to 90%
Non-operating
5% to 95%
* All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to
3048 m (10,000 ft) is applicable. No direct sunlight allowed.
** Storage maximum humidity of 95% is based on a maximum temperature of 45°C (113°F). Altitude maximum for
storage corresponds to a pressure minimum of 70 KPa.
Hot-plug power supply calculations
For hot-plug power supply specifications and calculators to determine electrical and heat loading for the
server, refer to the HP Enterprise Configurator website (http://h30099.www3.hp.com/configurator/).
DDR2 SDRAM DIMM specifications
NOTE: Use only 512-MB, 1-GB, 2-GB, 72-bit wide, PC2 3200 Registered ECC DDR2 SDRAM. Use HPbranded DDR2 SDRAM only.
Item
Description
Size
512 MB, 1 GB, 2 GB
Width
72 bits
Upgrade requirement Any combination of like-paired DDR2 SDRAM DIMMs that
provide a minimum of 512 MB
Specifications
52
1.44-MB diskette drive specifications
Specification
Value
Dimensions
Height
12.7 mm (0.5 in)
Width
96 mm (3.8 in)
Depth
130 mm (5.1 in)
LEDs (front panel)
Green = Active
Read/write capacity per
diskette
High density
1.44 MB
Low density
720 KB
Drives supported
1
Drive height
One-third height
Drive rotation
300 rpm
Transfer rate
High
500 Kb/s
Low
250 Kb/s
Bytes/sector
512
Sectors per track (high/low)
18/9
Tracks per side (high/low)
80/80
Access times
Track-to-track (high/low)
3 ms/6 ms
Average (high/low)
169 ms/94 ms
Setting time
15 ms
Latency average
100 ms
Cylinders (high/low)
80/80
Read/write heads
2
CD-ROM drive specifications
Specification
Value
Disk formats
CD-ROM (modes 1 and 2); mixed mode (audio and data combined); CD-DA;
Photo CD (single/multiple-session), CD-XA ready; CDi ready
Capacity
550 MB (mode 1, 12 cm)
640 MB (mode 2, 12 cm)
Block size
2368, 2352 bytes (mode 0)
2352, 2340, 2336, 2048 bytes (mode 1)
2352, 2340, 2336, 2048 bytes (mode 2)
Dimensions
Height
12.7 mm (0.50 in)
Depth
132.08 mm (5.20 in)
Specifications
53
Specification
Value
Width
132.08 mm (5.20 in)
Weight
0.34 kg (0.75 lb)
Data transfer rate
Sustained
150 KB/s (sustained 1X), 1500/3600 KB/s (10X to 24X)
Burst
16.6 MB/s
Access times
(typical)
Full stroke
300 ms
Random
140 ms
Diameter
12 cm, 8 cm (4.70 in, 3.15 in)
Thickness
1.2 mm (0.05 in)
Track pitch
1.6 µm (6.3 × 10-7 in)
Cache/buffer
128 KB
Startup time
< 10 s
Stop time
< 5 s (single); < 30 s (multisession)
Laser parameters
Type
Semiconductor laser GaAs
Wave length
700 ± 25 nm
Divergence angle
53.5° ± 1.5°
Output power
0.14 mW
Operating
conditions
Temperature
5°C to 55°C (41°F to 131°F)
Humidity
10% to 80%
Specifications
54
Acronyms and abbreviations
ABEND
abnormal end
ACU
Array Configuration Utility
ADU
Array Diagnostics Utility
ASR
Automatic Server Recovery
ATAPI
Advanced Technology Attachment Packet Interface
DDR
double data rate
DIMM
dual inline memory module
HD68
high density 68
IEC
International Electrotechnical Commission
iLO
Integrated Lights-Out
IML
Integrated Management Log
IPL
initial program load
Acronyms and abbreviations
55
IRQ
interrupt request
ISEE
Instant Support Enterprise Edition
MPS
multi-processor specification
NEMA
National Electrical Manufacturers Association
NFPA
National Fire Protection Association
NIC
network interface controller
NMI
non-maskable interrupt
NVRAM
non-volatile memory
ORCA
Option ROM Configuration for Arrays
PCI Express
peripheral component interconnect express
PCI-X
peripheral component interconnect extended
PDU
power distribution unit
POST
Power-On Self Test
PPM
processor power module
Acronyms and abbreviations
56
PSP
ProLiant Support Pack
PXE
Preboot Execution Environment
RBSU
ROM-Based Setup Utility
RILOE II
Remote Insight Lights-Out Edition II
SAS
serial attached SCSI
SATA
serial ATA
SCSI
small computer system interface
SDRAM
synchronous dynamic RAM
SIM
Systems Insight Manager
TMRA
recommended ambient operating temperature
UID
unit identification
VHDCI
very high density cable interconnect
WOL
Wake-on LAN
Acronyms and abbreviations
57
Index
A
access panel 14
Altiris Deployment Solution 37
Altiris eXpress Deployment Server 37
ASR (Automatic Server Recovery) 35, 54
Automatic Server Recovery (ASR) 35, 54
Autorun menu 38
B
Basic Input/Output System (BIOS) 37
battery 32
BIOS (Basic Input/Output System) 37
BIOS upgrade 37
buttons 39
C
CD-ROM drive 22, 52
component identification 39, 48
components 39
components, mechanical 6
components, system 7
configuration of system 37
connectors 39
creating a disk image 37
CSR (customer self repair) 5
customer self repair (CSR) 5
D
deployment software 37
diagnostic tools 35, 37, 38
diagnostics utility 38
DIMM slot LEDs 48
DIMMs 30
diskette image creation 37
drive cage assembly, SCSI 24
drive LEDs 48
duplex SCSI backplane 31
E
electrostatic discharge 11
environmental requirements 51
environmental specifications 51
expansion boards 21
expansion slot covers, removing 20
F
fan LED 48
fans 19
features 39
flash ROM 37
front bezel 15
front panel components 39
front panel LEDs 40
H
half-height media device 22
hard drive blanks 16
hard drive LEDs 48
hard drives 24, 48
hard drives, determining status of 48
health driver 35, 48
health LEDs 48
heatsink 25
hot-plug power supply 16
hot-plug power supply backplane 16
HP Insight Diagnostics 38
HP Instant Support Enterprise Edition 36
HP ProLiant Essentials Foundation Pack 36
HP ProLiant Essentials Rapid Deployment Pack 37
HP Systems Insight Manager, overview 36
I
illustrated parts catalog 5
iLO (Integrated Lights-Out) 54
IML (Integrated Management Log) 36
Insight Diagnostics 38
Instant Support Enterprise Edition 36
Integrated Lights-Out (iLO) 54
Integrated Management Log (IML) 36
L
LED, fan 48
Index 58
LEDs 39
LEDs, hard drive 48
M
management tools 35
mechanical components 6
media devices 22, 23
N
network interface controller (NIC) 55
NMI jumper 44
O
Online ROM Flash Component Utility 37
Option ROM Configuration for Arrays (ORCA) 36
P
part numbers 5
Power On/Standby button 13
power requirements 51
power supplies 16, 51
power supply blank 16
power supply output 51
powering down 13
PPM (processor power module) 29
preparation procedures 12
Processor Power Module (PPM) 29
processors 25
ProLiant Support Pack (PSP) 55
PSP (ProLiant Support Pack) 55
S
safety considerations 10
safety information 10
SAS drive numbers 24
SAS drives 49
SATA hard drive 18, 49
SCSI backplane, duplex 31
SCSI hard drive 16, 18
SCSI IDs 47
serial number 34
serial port 31
server specifications 50, 51
SmartStart autorun menu 38
SmartStart, overview 38
specifications 50, 51
specifications, environmental 50, 51
specifications, server 50, 51
static electricity 11
support packs 38
symbols on equipment 11
system board 33, 43
system board LEDs 46
system components 7
system maintenance switch 44
Systems Insight Manager 36
T
tape drives 23
telco racks 12
tools 35
tower feet 14
R
U
rack warnings 12
RBSU (ROM-Based Setup Utility) 37
rear components 41
rear panel LEDs 42
redundant system fan 19
remote support and analysis tools 36
removal and replacement procedures 10
removing server from rack 14
required tools 10
requirements, environmental 51
requirements, power 51
ROM-Based Setup Utility (RBSU) 37
ROMPaq utility 37
UID LEDs 13
updating the system ROM 37
utilities 35
utilities, deployment 37
Index 59
Download PDF
Similar pages