INSTRUCTION MANUAL
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
12 V MAX* VARIABLE SPEED JIG SAW
SCIE SAUTEUSE À VITESSE VARIABLE DE 12 V MAX*
SIERRA CALADORA DE VELOCIDAD VARIABLE
DE 12 V MAX*
BCS601
Please read before returning this product for any reason.
à LIRE avant de retourner ce produit pour quelque raison que
ce soit.
LEA EL MANUAL antes de devolver este producto por
cualquier motivo.
final page size: 8.5 x 5.5 in
English
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
Fig. A
6
7
2
1
3
8
4
5
1 Variable speed switch
2 Lock-off button
3 Saw blade locking lever
4 Shoe
5 Blade
6 Battery (may be sold separately)
7 Battery release button
8 Blade storage
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the
instruction manual.
Imported by .Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286
BlackandDecker.com
1-800-544-6986
1
English
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless)
power tool.
1) Work Area Safety
a ) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b ) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c ) Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
2) Electrical Safety
a ) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b ) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c ) Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
d ) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e ) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f ) If operating a power tool in a damp location
is unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of a GFCI
reduces the risk of electric shock.
3) Personal Safety
a ) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
2
b ) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c ) Prevent unintentional starting. Ensure the
switch is in the off position before connecting to
power source and/or battery pack, picking up
or carrying the tool. Carrying power tools with your
finger on the switch or energizing power tools that
have the switch on invites accidents.
d ) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e ) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
g ) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
4) Power Tool Use and Care
a ) Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
b ) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c ) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
d ) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dangerous
in the hands of untrained users.
e ) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits, etc.
in accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
b ) Use power tools only with specifically
designated battery packs. Use of any other battery
packs may create a risk of injury and fire.
c ) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws, or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
6) Service
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Jig Saw Safety Warnings
•
•
•
•
•
•
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
Keep hands away from cutting area. Never reach
underneath the material for any reason. Hold front of saw
by grasping the contoured gripping area. Do not insert
fingers or thumb into the vicinity of the reciprocating
blade and blade clamp. Do not stabilize the saw by
gripping the shoe.
Keep blades sharp. Dull blades may cause the saw to
swerve or stall under pressure.
Use extra caution when cutting overhead and pay
particular attention to overhead wires which may be
hidden from view. Anticipate the path of falling branches
and debris ahead of time.
When cutting pipe or conduit ensure that they are free
from water, electrical wiring, etc.
English
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber (CCA).
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding,
sawing, grinding, drilling, and other construction
activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals.
SAVE THESE INSTRUCTIONS
Additional Safety Information
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemicallytreated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
3
English
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.
WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
CAUTION: When not in use, place tool on its side
on a stable surface where it will not cause a
tripping or falling hazard. Some tools with large
battery packs will stand upright on the battery pack
but may be easily knocked over.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V.......................... volts
or AC/DC..... alternating or
direct current
Hz........................ hertz
....................... Class II
min...................... minutes
Construction
or DC....... direct current
(double insulated)
....................... Class I Construction
no........................ no load speed
(grounded)
n.......................... rated speed
…/min............... per minute
....................... earthing terminal
BPM..................... beats per minute
...................... safety alert symbol
IPM...................... impacts per minute
...................... visible radiation
RPM..................... revolutions per
...................... wear respiratory
minute
protection
sfpm.................... surface feet per
...................... wear eye
minute
protection
SPM..................... strokes per minute
...................... wear hearing
A.......................... amperes
protection
W......................... watts
...................... read all
or AC............ alternating current
documentation
BATTERIES
The battery pack is not fully charged out of the carton.
Before using the battery pack, read the safety instructions
below and then follow charging procedures outlined. When
ordering replacement battery packs, be sure to include the
catalog number and voltage.
READ ALL INSTRUCTIONS
Important Safety Instructions for All
Battery Packs
•
4
WARNING: Read all safety warnings and all
instructions for the battery pack, and power tool.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Do not charge or use the battery pack in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the
•
•
•
•
•
•
charging cable from the battery pack may ignite the dust
or fumes.
NEVER force the battery pack into cable insertion
or tool insertion. DO NOT modify the battery pack
in any way as battery pack may rupture causing
serious personal injury.
DO NOT splash or immerse in water or other liquids.
Do not store or use the tool and battery pack in
locations where the temperature may reach or
exceed 104 °F (40 °C) (such as outside sheds or metal
buildings in summer). For best life store battery packs in
a cool, dry location.
NOTE: Do not store the battery packs in a tool with
the trigger switch locked on. Never tape the trigger
switch in the ON position.
Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
materials are created when lithium ion battery packs
are burned.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte is composed of
a mixture of liquid organic carbonates and lithium salts.
Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persist, seek medical attention.
WARNING: Burn hazard. Battery liquid may be
flammable if exposed to spark or flame.
WARNING: Fire hazard. Never attempt to open the
battery pack for any reason. If the battery pack case is
cracked or damaged, do not attempt to use or charge.
Do not crush, drop or damage the battery pack. Do
not use a battery pack or charger that has received a
sharp blow, been dropped, run over or damaged in
any way (e.g., pierced with a nail, hit with a hammer,
stepped on). Damaged battery packs should be
returned to the service center for recycling.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
NOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
The RBRC® Seal
The RBRC® (Rechargeable Battery Recycling
Corporation) Seal on the nickel cadmium,
nickel metal hydride or lithium-ion batteries
(or battery packs) indicates that the costs
to recycle these batteries (or battery packs)
at the end of their useful life have already been paid by
English
BLACK+DECKER. In some areas, it is illegal to place spent
nickel cadmium, nickel metal hydride or lithium-ion
batteries in the trash or municipal solid waste stream and
the Call 2 Recycle® program provides an environmentally
conscious alternative.
Call 2 Recycle, Inc., in cooperation with BLACK+DECKER
and other battery users, has established the program in
the United States and Canada to facilitate the collection
of spent nickel cadmium, nickel metal hydride or
lithium-ion batteries. Help protect our environment and
conserve natural resources by returning the spent nickel
cadmium, nickel metal hydride or lithium-ion batteries to
an authorized BLACK+DECKER service center or to your
local retailer for recycling. You may also contact your
local recycling center for information on where to drop
off the spent battery. RBRC® is a registered trademark of
Call 2 Recycle, Inc.
Getting Started
• The Micro USB port ( 12 ) on the BLACK+DECKER GoPak
2 in 1 power source is only to be used for charging the
GoPak.
• The USB A port ( 11 ) the BLACK+DECKER GoPak 2 in 1
power source is only to be used for powering USB
devices (Phone/Tablet/MP3/Wearable/Game Controller/
etc.).
Fig. B
12
11
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65 °F – 75 °F (18 ° – 24 °C). DO NOT charge the
battery pack in an air temperature below 40 °F (4.5 °C),
or above 104 °F (40 °C). This is important and will
prevent serious damage to the battery pack.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the power adapter and battery pack to a
location where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and power adapter to your local service center.
3. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
Transportation
WARNING: Fire hazard. Do not store or carry the
battery pack so that metal objects can contact
exposed battery terminals. For example, do
not place the battery pack in aprons, pockets, tool
boxes, product kit boxes, drawers, etc., with loose
nails, screws, keys, etc. Transporting batteries
can possibly cause fires if the battery terminals
inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the
like. The US Department of Transportation Hazardous
Material Regulations (HMR) actually prohibit
transporting batteries in commerce or on airplanes in
carry-on baggage UNLESS they are properly protected
from short circuits. So when transporting individual
battery packs, make sure that the battery terminals
are protected and well insulated from materials that
could contact them and cause a short circuit.
Charging the Black+Decker GoPak 2 in 1
Power Source (Fig. A, C)
WARNING: Never attempt to charge the
BLACK+DECKER GoPak 2 in 1 power source using the
tool terminals on the GoPak.
WARNING: You should only charge the
BLACK+DECKER GoPak 2 in 1 power source using USB
ports rated for charging high performance devices.
The GoPak can pull more current than acceptable
with older USB ports. An error message may display
on your computer if the computer is used to charge
the GoPak.
1. Plug the micro USB cable (included) ( 13 ) into a USB
power supply (not included).
2. Plug the micro USB plug of your charger cord into the
GoPak micro USB port ( 12 ).
3. As the GoPak charges, the State of Charge LEDs will
illuminate. The illuminated LED(s) indicate the state
of charge of the pack. The blinking LED indicates the
next level of charge in progress. The State of Charge
button ( 9 ) is disabled during charging only.
4. The completion of charge is indicated by all four LEDs
turning off. Pressing the state of charge indicator
button ( 9 ) will illuminate all four LEDs. The power source
is fully charged and may be used at this time or left on
the charger.
5. Recharge discharged power sources as soon as possible
after use or power source life may be greatly diminished.
For longest power source life, do not discharge power
sources fully. It is recommended that the power sources
be recharged after each use.
5
English
GoPak Tool Terminal Safety Cap
Fig. C
13
12
A power source storage and carrying cap ( 7 ) is provided for
use whenever the power source is out of the tool. Remove
the cap as shown in Figure B before placing power source
onto tool.
Fig. E
10
State Of Charge Indicator (Fig. D)
The BLACK+DECKER GoPak 2 in 1 power source is equipped
with a state of charge indicator button ( 9 ) with a four
LED display.
The State Of Charge Indicator is an indication of
approximate levels of charge remaining in the power source
according to the following indicators:
96-100% charged
76-95%
51-75%
26-50%
Pack needs to be charged
To actuate the State Of Charge Indicator, press the State Of
Charge Indicator button. A combination of the four LEDs
will illuminate designating the level of charge left. When
the level of charge in the power source is below the usable
limit, the State Of Charge Indicator LEDs will either not light
or the bottom LED will blink.
NOTE: The LED state of charge will only display once the
state of charge button is pressed.
Fig. D
9
• Press state of charge button at anytime to display the
remaining level of charge.
NOTE: The State Of Charge Indicator is only an indication
of the charge left on the power source. It does not
indicate tool functionality and is subject to variation
based on product components, temperature and enduser application.
NOTE: GoPak power source safety cap should be used when
power source is not connected to a power tool. Safety cap
is provided for use whenever the power source is out of the
tool. Remove cap before placing power source into tool.
6
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)
WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.
Intended Use
Your BLACK+DECKER BCS601 jig saw has been designed for
sawing wood, plastics and sheet metal. This tool is intended
for consumer use only.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
English
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: Laceration Hazard. Before attempting any
of the following operations, make sure that the tool is
switched off and the battery is removed, and that the
saw blade has stopped. Used saw blades can be hot.
WARNING: Remove power source when removing or
installing the blade
Fitting the saw blade (Fig. A, F)
1. Hold the saw blade 5 as shown, with teeth
facing forward.
2. Push the locking lever ( 3 ) up away from the shoe ( 4 ).
3. With the teeth facing forward, insert the shank of the
saw blade into the blade holder ( 18 ) as far as it will go.
4. Release the lever.
5. Pull blade to be sure the blade is fully secured.
Fig. F
3
18
4
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: To reduce the risk of injury, never use the
tool when the saw shoe is loose or removed.
Installing and Removing the GoPak 2 in 1
Power Source in a Power Tool (Fig. G)
WARNING: Remove any connected USB cords from
the BLACK+DECKER GoPak 2 in 1 power source before
connecting the GoPak to the compatible tool.
1. Remove the tool terminal safety cap if installed on the
BLACK+DECKER GoPak 2 in 1 power source.
2. To power a compatible GoPak 12V MAX* power tool,
align the tool terminals on the foot of the tool with
the terminal slots on the power source ( 6 ) as shown in
Figure E.
NOTE: The state of charge indicator will face the rear of the
tool and the USB ports will face the front. The arrow on the
power source will align with the arrow on the tool as shown
in Fig. E.
3. Snap the BLACK+DECKER GoPak 2 in 1 power source
into the foot of the tool. The arrow ( 16 ) on the power
source will align with the arrow ( 17 ) on the tool. Ensure
the power source is fully seated and fully latched into
position before using.
4. To remove the BLACK+DECKER GoPak 2 in 1 power
source from the tool, depress the two power source
release buttons ( 7 ) located on the tool and pull the
BLACK+DECKER GoPak 2 in 1 power source off the tool.
NOTE: The BLACK+DECKER GoPak 2 in 1 power source USB
ports are disabled when the trigger is pulled.
Fig. G
17
16
7
6
Using the GoPak 2 in 1 power source to
charge your USB device (FIg. H)
1. Plug the USB A end of your device specific cable ( 14 )
into the BLACK+DECKER GoPak 2 in 1 power source ( 11 )
and the other end of the cable into a compatible device
7
English
(Phone/Tablet/MP3/Wearable/Game Controller/etc.).
Charging will start automatically.
Fig. H
14
Fig. I
2
11
Functionality
The BLACK+DECKER GoPak 2 in 1 power source can power
your compatible BLACK+DECKER 12V GoPak MAX* tools
or power/charge your mobile devices. The compact, slim
power source housing is designed for portability.
-- GoPak Charge Input: Up to 2.4A**
-- GoPak Power Output: Up to 2.4A***
** Actual input charge rate is dependant upon power
adapter (not included).
***Actual output rate is dependant on the device.
• To switch the tool on, press the variable speed
switch 1 . The tool speed depends on how far you
depress the switch.
• To switch the tool off, release the variable speed switch.
How to Use the Sightline® Feature (Fig. J)
1. Use a pencil to mark the cutting line.
2. Position the jig saw over the line 15 .
3. Viewing from directly above the jig saw, the line of cut
can be easily followed.
Fig. J
USB Power Port
The BLACK+DECKER GoPak 2 in 1 power source is equipped
with a USB Type A power port. It delivers up to 2.4 amp
total current.
NOTE: The current delivered to device is dependent on user
device and user's chosen cable.
WARNING: Ensure the safety cap is securly attached
to the BLACK+DECKER GoPak 2 in 1 power source
when using it to power/charge your device.
• Install safety cap on the tool terminals.
• Device charging from USB will start automatically when
device is connected.
• To turn OFF, disconnect USB device.
15
Hints for optimum use
General
Use a high speed for wood, a medium speed for
aluminum and PVC and a low speed for metals other then
aluminum Specific materials also require specialty blades
(sold separately).
Proper Hand Position
Sawing laminates
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
and one hand on the auxiliary handle.
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
• Use a fine-tooth saw blade.
• Saw from the back surface of the workpiece.
• To minimize splintering, clamp a piece of scrap wood
or hardboard to both sides of the workpiece and saw
through this sandwich.
Switching On and Off (Fig. I)
Sawing metal
This tool is equipped with a lock-off button 2 . The button
must be disengaged for the jig saw to turn on. To disengage
the button, depress the button on the side of the handle
that shows the unlock symbol.
8
• Be aware that sawing metal takes much more time than
sawing wood.
• Use a saw blade suitable for sawing metal.
• When cutting thin metal, clamp a piece of scrap wood
to the back surface of the workpiece and cut through
this sandwich.
• Spread a film of oil along the intended line of cut.
English
Pocket Cutting (Fig. K)
A pocket cut is an easy method of making an inside cut. The
saw can be inserted directly into a panel or board without
first drilling a lead or pilot hole. In pocket cutting, measure
the surface to be cut and mark clearly with a pencil. Next tip
the saw forward until the front end of the shoe sits firmly
on the work surface and the blade clears the work through
its full stroke. Switch the tool on and allow it to attain
maximum speed. Grip the saw firmly and lower the back
edge of tool slowly until the shoe sits flate on the surface.
Hold the shoe flat against the wood and continue cutting.
Do not remove blade from cut while it is still moving. Blade
must come to a complete stop.
Fig. K
9
English
MAINTENANCE
TWO-YEAR LIMITED WARRANTY
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Use only mild soap and damp cloth to clean the tool. Never
let any liquid get inside the tool; never immerse any part of
the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment should be performed
by authorized service centers or other qualified service
organizations, always using identical replacement parts.
Black & Decker (U.S.) Inc. warranties this product to be free
from defects in material or workmanship for a period of
two (2) years following the date of purchase, provided that
the product is used in a home environment. This limited
warranty does not cover failures due to abuse, accidental
damage or when repairs have been made or attempted
by anyone other than BLACK+DECKER and its Authorized
Service Centers. A defective product meeting the warranty
conditions set forth herein will be replaced or repaired at no
charge in either of two ways:
The first, which will result in exchanges only, is to return
the product to the retailer from whom it was purchased
(provided that the store is a participating retailer). Returns
should be made within the time period of the retailer’s
policy for exchanges. Proof of purchase may be required.
Please check with the retailer for its specific return policy
regarding time limits for returns or exchanges.
The second option is to take or send the product
(prepaid) to a BLACK+DECKER owned or authorized Service
Center for repair or replacement at BLACK+DECKER’s
option. Proof of purchase may be required. BLACK+DECKER
owned and authorized service centers are listed online
at www.blackanddecker.com. This warranty does not
apply to accessories. This warranty gives you specific
legal rights aand you may have other rights which vary
from state to state or province to province. Should
you have any questions, contact the manager of your
nearest BLACK+DECKER Service Center. This product is
not intended for commercial use, and accordingly, such
commercial use of this product will void this warranty. All
other guarantees, express or implied, are hereby disclaimed.
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
check country specific warranty information contained in
the packaging, call the local company or see the website for
warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-544-6986
for a free replacement..
Cleaning
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool or power supply. These chemicals may weaken
the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let
any liquid get inside the tool or power supply; never
immerse any part of the tool or power supply into
a liquid.
NOTE: Remove tool and both USB cables from GoPak
before cleaning.
Use only mild soap and a damp cloth to clean the tool or
power supply. Many household cleaners contain chemicals
which could seriously damage plastic. Also, do not use
gasoline, turpentine, lacquer or paint thinner, dry cleaning
fluids or similar products.
TROUBLE SHOOTING
1.The GoPak will not power your device or charge.
a.The LED closest to the state of charge button will
blink red when attempting USB functionality.
-- The GoPak is too hot or too cold. Allow the GoPak to
cool down or warm up.
2.The GoPak will not power your compatitible tool.
-- Attempt to charge the power source. If the LED fails
to come on refer to number 1 in Troubleshooting.
Repairs
The BLACK+DECKER GoPak 2 in 1 power source is
not serviceable.
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a BLACK+DECKER factory service
center or a BLACK+DECKER authorized service center.
Always use identical replacement parts.
10
Accessories
WARNING: Since accessories, other than those
offered by BLACK+DECKER have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
BLACK+DECKER recommended accessories should be
used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact BLACK+DECKER, call
1-800-544-6986.
English
TROUBLESHOOTING
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest
you or call the BLACK+DECKER help line at 1-800-544-6986.
Problem
Possible Cause
Possible Solution
Unit will not start.
Power source not installed properly.
Check power source installation.
Power source not charged.
Check power source charging requirements.
Internal components too hot.
Allow tool to cool down.
Cables not properly connected.
Check the cable connections to the power
source.
Power source not plugged in.
Check the connections between the power
source, the device used to charge the power
source and the working outlet.
Surrounding air temperature too hot or too cold.
Move power source to a surrounding air
temperature of above 40 degrees F (4.5 °C) or
below 105 degrees F (+40.5 °C).
Power source has reached its maximum thermal
limit.
Allow power source pack to cool down.
Out of charge. (To maximize the life of the
power source it is designed to shutoff
abruptly when the charge is depleted.)
Place on charger and allow to charge.
Power source will not charge.
Unit shuts off abruptly.
11
Download PDF
Similar pages