Sonata-2 Instructions
Remove the fire from the packing, checking that neither the heater nor the power cable has been damaged during transport. Do not operate the
heater if damaged. The accessories are found in a box that is packed at the side of the fire. Your fire is guaranteed for one year from the date of
purchase. In the unlikely event of a breakdown you have access to our customer services team, simply call 01543 251122 during office hours, 9am
– 5pm or e-mail on info@flameritefires.com
Installation of Fire
Where a chimney is not blocked off completely it will cause the heater to cut out during use.
Your fire has been designed for use as part of a fireplace mantel and surround suite. A minimum depth of up to 140mm may be required. The
dimensions of the aperture in the decorative back panel into which the fire fits are, height maximum 595mm and minimum 560mm and width
maximum 440mm and minimum 405mm. The fire must be positioned so that the plug socket is accessible once the fire has been installed. In the
unlikely event of breakdown access must be allowed to the rear so that the fire maybe serviced, do not seal to the wall. The mains cable must
therefore be long enough to allow this. If the removal of the plug is absolutely necessary for installation, cut off in an area within 100mm only of
the plug itself. Any further may affect your warranty. Where the inset fire is being used in an existing chimney, it is important that the chimney is
blocked off to prevent airflow problems with the fire. Where a chimney is not blocked off sufficiently, it may cause the heater to cut out and the
flame effect to stop or work inefficiently.
Electrical connections
Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement fuses must be 13A and ASTA approved. If the fuse cover is
lost the plug must not be used until a replacement cover, of the same colour, is obtained from an electrical retailer.
The appliance is fitted with a moulded plug if it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse
removed. Under no circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as this could cause a
hazard. If the mains cable is damaged it must be replaced by the manufacturer or an authorised technical service centre.
WARNING THIS APPLIANCE MUST BE EARTHED
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code.
Green and yellow:
EARTH
Blue:
NEUTRAL
Red:
LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in your plug proceed as follows: The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E, or
coloured green or coloured green and yellow, or marked with the earth symbol
The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N, or coloured
black.
The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L, or coloured
red.
Fuel Effects
Once the firep has been installed in the correct position unpack the fuel effect from the accessory box and arranged in a random formation
on top of the fuel bed.
Operating the fire
Controls (Remote)
The main on/off switch is marked with I/O and will need to be switched to I to operate the fire. In this position you will be
unable to operate the fire further unless the
button on the remote or keypad is pressed first.
To operate the flame effect (and further functions) simply press and release the button on the remote or keypad.
To set the flame effect to your desired brightness press then release + or - buttons marked either side of the
For 750W of heat, press then release the button marked
button marked
icon.
O/I. To increase the temperature to 1.5KW press then release
I/II. You may alternate from 750W to 1.5KW by pressing
I/II at anytime. To turn the heater off, press
then release the button marked
O/I. The heater will always start on the lower setting
To turn the flame effect off and deactivate the heater and dimmer functions press then release the button marked
To turn the fire off completely the main on/off switch must be switch back to O.
Page 1 of 2
.
(Operating the fire continued)
Controls (Manual)
The main on/off switch is marked with I/O and will need to be switched to I to operate the fire and illuminate the flame effect.
For heating the Push Switch is located on the opposite side to the on/off switch. For 1.5KW of heat push the switch marked with
a single bar I. The flame effect has to be illuminated for the heater to work.
To turn the fire off completely the main on/off switch must be switch back to O.
Areas around the fire will become hot when activated. We strongly recommend small children be kept away from having any direct
contact with the appliance by means of fitting a fireguard. This appliance is not intended for use by persons (or children) with reduced
physical sensory or mental capabilities or lack of experience or knowledge unless they have been given supervision or instruction
concerning the use of the appliance by the person responsible for their safety. Children should be supervised to ensure they do not
play with this appliance.
Automatic safety cut out
The heater is fitted with an automatic cut out to prevent any damage due to overheating. The element will continually and automatically
cut out if the airflow is obstructed. Never cover the air inlets or outlets. To reset the fire, switch the fire off, disconnect from the mains
supply, remove the cause of overheating and allowed to cool for a suitable period then switch the fire back on. Caution: In order to avoid a
hazard due to inadvertent resetting of the thermal cut out, the appliance must not be supplied through an external switching device, such
as a timer, or connected to circuit regularly switched on and off by a utility.
Maintenance
Before any maintenance/cleaning is undertaken always disconnect the fire from the mains power supply.
Replacing the Lamp (Dimmable 240V 5W 3000k E14 LED lamp if remote/Non Dimmable if manual): Replacements are available from Flamerite
Fires info@flameritefires.com
Allow a suitable time for the lamp to cool then remove the fuel effect, the screws and the orange fuel bed, the lamp will be visible. Please note
that replacement Lamps are only covered by a 2 year warranty from date of purchase.
Changing battery in the remote
On the reverse side of the remote near the bottom is the access plate to the battery compartment. Remove by placing your nail under the catch,
push and lift. We only recommend an alkaline battery MN21 12 Volt. Ensure battery is disposed of safely. Do not dispose of in fire, do not
swallow and keep away from children.
Cleaning
The fire can be cleaned with a damp cloth and non abrasive cleaner. Be sure not to press/rub too hard as to remove the paint.
Warnings
Do not use the fire in the vicinity of a bath shower or swimming pool.
Never use the fire to dry laundry.
Never install the fire directly underneath a fixed main socket.
Never cover the appliance during the operation of the fire.
The use of an extension lead is not recommended.
Particular caution should be applied to ensure that children do not play with the pebbles/coal.
As with any electrical appliance whilst the instructions aim to cover as many eventualities as possible, caution and common sense should
be applied when operating your appliance, particularly in the vicinity of small children.
Problem solving
No power to the fire: Check the wall socket, plug and fuse.
No illumination: Make sure fire is turned on. Check heater is working, if not see Replacing the lamp above.
Illumination but no heat: The safety cut has operated see notes on Operating and Installation the Fire.
Noise when illuminated: Due to moving parts, the electric fire will make a noise.
Noise from the heater when in use: The sound of rushing air is normal.
Page 2 of 2
Download PDF
Similar pages