436 MILITARY WHEELED LOADING SHOVEL | 436 HT

436 MILITARY WHEELED LOADING SHOVEL | 436 HT
MAX. ENGINE POWER: 132kW (177hp)
MAX. OPERATING WEIGHT: 16897kg (37251lb)
MAX. LOADER CAPACITY: 2.7m3 (3.5yd3)
STATIC DIMENSIONS
LOADER DIMENSIONS
N
G
M
T
J
Q
F
R
O
S
E
H1
H
B
C
P
D
A
HT
A Overall length
mm (ft-in)
B
Axle to pivot pin
HT
6926 (22-9)
Tipping load straight
kg (lb)
11467 (25280)
mm (ft-in)
1143 (3-9)
Tipping load full turn
kg (lb)
9578 (21116)
C Wheel base
mm (ft-in)
3000 (9-10)
Payload
kg (lb)
4789 (10558)
D Axle to counterweight face
mm (ft-in)
1816 (5-11)
Maximum break out force
kN (lbf)
147 (33048)
E
Minimum ground clearance
mm (ft-in)
459 (1-6)
M Dump angle maximum
degrees
50°
F
Height over exhaust
mm (ft-in)
3192 (10-6)
N Roll back angle full height
degrees
58°
G Width over cab
mm (ft-in)
1400 (4-7)
O Roll back at carry
degrees
48°
H Width over tyres
mm (ft-in)
2597 (8-6)
P
degrees
H1 Wheel track
mm (ft-in)
2070 (6-9)
Q Load over height
mm (ft-in)
3755 (12-3)
J
Height over cab
mm (ft-in)
3335 (10-11)
R
Dump height (45° dump)
mm (ft-in)
2974 (9-8)
Pin height (maximum)
mm (ft-in)
3996 (13-1)
S
Dig depth
mm (ft-in)
106 (0-4)
Overall operating height
mm (ft-in)
5305 (17-4)
T
Reach at dump height
mm (ft-in)
1044 (3-5)
Reach maximum (45° dump) – horizontal arm
mm (ft-in)
Front axle weight
kg (lb)
6013 (13256)
Rear axle weight
kg (lb)
8490 (18717)
Total weight
kg (lb)
14503 (31974)
Inside radius
mm (ft-in)
2825 (9-3)
Maximum radius
mm (ft-in)
5860 (19-3)
Articulation angle
degrees
Roll back at ground level
Operating weight (includes 80kg operator and full fuel tank)
± 40°
Data based on machine equipped with pin mounted 2.4m3 bucket with toe plates and Michelin 20.5R25 XHA (L3) radial tyres.
kg (lb)
43°
1883 (6-2)
14503 (31973)
436 MILITARY WHEELED LOADING SHOVEL | 436 HT
STANDARD EQUIPMENT
Loader: Bucket reset mechanism, loader arm kickout mechanism, loader control isolator, single lever servo control, high torque
geometry combines with excellent visibilty between the arms.
Engine: Air cleaner - 2 stage dry type - cyclonic with primary and safety elements, silencer and exhaust stack, sedimenter,
twin bowl fuel filters, alternator and compressor drive belt guards. Isolated cooling package with hydraulically driven cooling fan.
ELECTRICAL SYSTEM
24 volt negative ground system, 70 Amp alternator with 2 x 110 Amp hour low maintenance batteries. Isolator located in rear
of machine. Ignition key start/stop and pre-heat cold start. Primary fuse box. Other electrical equipment includes quartz halogen,
twin filament working lights, front/rear wash/wipe, heated rear screen, full road going lights, clock, gauge and warning light
monitoring. Connectors to IP67 standard.
Transmission: Single lever shift control, speed inhibitor, neutral start, disconnect on footbrake and loader lever, disconnect isolator
switch, direction changes and kickdown on gear selector and loader control lever.
Axles: Epicyclic wheel hub reduction, fixed front, oscillating rear.
Brakes: Multi-plate wet disc brakes, organic linings, dual circuit hydraulic power assisted. Parking disc brake on transmission
output shaft.
Hydraulics: Twin piston pump with priority steer, emergency steer back-up, 2 spool loader circuit with accumulator support,
3rd spool auxiliary hydraulic circuit as standard. Hydraulic tank located in the rear chassis fabrication.
Steering: Adjustable steering column, “soft feel” steering wheel 5 turns lock to lock, resilient stops on max lock.
Cab: ROPS/FOPS safety structure, interior reading light, centre mounted master warning light. Electronic monitoring panel with
LCD message display. Two speed intermittent front windscreen wipe/wash and self park, single speed rear windscreen wipe/wash
and self park. 3 speed heater/demisting with replaceable air filter, LH and RH opening windows, sun visor, sun blind, internal
rear view mirror, heated external mirrors, adjustable suspension seat with belt and headrest, operator storage facilities, laminated
windscreen, heated rear screen, loader control isolator, horn.
CAB
Resiliently mounted ROPS/FOPS structure (tested in accordance with ISO 3471-1 : 1986 / ISO 3449 : 1984). De - luxe operator
environment combines ergonomically located controls with a high level of appointment and low internal noise levels. Entry/exit is
via large rear hinged door and anti - slip steps. Excellent forward visibility is provided by a 3 section curved, laminated windscreen
and low waistline. Extensive instrumentation includes electronic monitoring panel and display (EMS). Heating / ventilation provides
balanced and filtered air distribution throughout the cab via a powerful 11 kW capacity heater. The unitary construction allows easy
sealing and prevents ingress of dust. A transmission lock on the selector prevents inadvertent engagement and the loader controls
can be isolated for safe road travel. Noise level measured in accordance with 86/662/EEC, amendment 95/27/EC
Interior pressure
:
level
73 Lp (A)
Exterior power
:
level
105 Lw (A)
Electrical: Road lights front and rear, parking lights, front and rear working lights, reverse alarm and light, rear fog light, battery
isolator, radio wiring and speakers, 70 amp alternator, rotating beacon.
TRANSMISSION
Bodywork: Front and rear fenders, side and rear access panels, flexible bottom step, full width rear counterweight, recovery hitch,
lifting lugs. RAL 6031 military green.
OPTIONAL EQUIPMENT
Auxiliary 4th spool hydraulic service, air conditioning, limited slip differentials front/rear axles, additional counterweight, turbo 2 precleaner, tooth guard, replaceable bucket wearparts, epoxy coated radiator/coolers, stainless steel brake pipes, smooth ride system
(SRS), hydraulic quickhitch with in-cab hydraulic pin isolation, reversing camera (colour), auto greasing system, joystick or Multi-lever
hydraulic controls, auxiliary hydraulic control on seperate lever or joystick mounted (proportional), Smart reverse alarm, parallel lift links
(recommended for pallet forks), widecore radiator, sealed electrics, grease gun and cartridge, basic and full belly guard kits, mesh air
intake screen, ARV kit, safety strut, transmission cooler bypass, 24V to 12V in cab converter, cab screen guards, air suspension seat, fire
extinguisher, number plate light kit, additional front and rear worklights, automatically reversing fan, LiveLink telematics, convoy lights,
extensive range of attachments.
4 wheel drive, automatic smooth shift transmission electrically operated selector and gear change incorporating a speed inhibitor
and modulation for smooth, responsive on-the-move direction and ratio changes. Single stage integral torque converter
4 forward and 3 reverse gears.
Type
Smooth shift powershift
Make & model
ZF 4WG 190
Torque converter stall ratio
2.873 : 1
Max. speed
kph (mph)
37.9 (23.5)
AXLES
MILITARY EQUIPMENT
-40° cold climate kit, 1.5m water wading kit, blackout lighting, convoy lighting, front winch, rifle brackets, ancillary equipment storage,
specialised paint.
LOADER HYDRAULICS
Variable displacement piston pumps feed a “load sensing” system providing a fuel efficient and responsive distribution of power as
required. Main services are servo actuated from a single lever (joystick) loader control. Auxiliary circuits controlled via additional lever
or joystick mounted electrical buttons. Accumulator back-up is available to control loader in the event of loss of pump pressure.
Type
Make & model
Overall axle ratio
Rear axle oscillation
Epicyclic hub reduction
Graziano PR12 B.O. front and rear
21.098 : 1
21°
436 MILITARY WHEELED LOADING SHOVEL | 436 HT
STEERING
F
Priority steer hydraulic system with emergency steering. Piston pump meters flow through steer valve @ 190 bar (2756 lb/in ) to
provide smooth low effort response. Steering angle ± 40°. Steer rams located high in the chassis fabrication to provide protection
from damage. Adjustable steering column.
2
BRAKES
E
Hydraulic power braking on all wheels, operating pressure 80 bar (1160psi). Dual circuit with accumulator back-up provide
maximum safety under all conditions. Hub mounted, oil immersed, multi-plate disc brakes with organic brake linings are
environmentally acceptable. Parking brake, mechanical disc type operating on transmission output shaft.
D
A
LOADER
B
Widely spaced four ram geometry provides the combination of excellent visibility with high bucket torque characteristics
throughout the working arc. The pin, bush and sealing design on all pivot points provide extended maintenance intervals.
LOADER DIMENSIONS – FORK FRAME WITH FORKS
assumes Michelin 20.5R25 XHA (L3) tyres
ENGINE
6-cylinder wastegated turbo-charged, liquid cooled, direct injection common rail diesel. Air-to-air charge-air cooling ensure
low emissions and “clean-burn” combustion chamber provides minimum fuel consumption. A remote sump oil drain facility
simplifies servicing.
Type
Make & model
Capacity
litres
1500 (4-11)
1500 (4-11)
Length of tines
mm (ft-in)
1220 (4-0)
1220 (4-0)
A Reach at ground level
mm (ft-in)
791 (2-7)
798 (2-7)
B
mm (ft-in)
1613 (5-4)
1620 (5-4)
Reach at arms horizontal
C Below ground level
mm (ft-in)
8 (0-3⁄8)
16 (0-5⁄8)
D Arms, horizontal height
mm (ft-in)
1946 (6-5)
1936 (6-4)
3818 (12-6)
E
Arms, maximum height
mm (ft-in)
3828 (12-7)
F
Reach at maximum height
mm (ft-in)
862 (2-10)
869 (2-10)
6.7
Turbo charged
6
Max gross power to SAE J1995/ISO 14396
kW (hp) @ 2000rpm
133 (178)
Rated gross power to SAE J1995/ISO 14396
kW (hp) @ 2200rpm
129 (173)
kW (hp) @ 2200rpm
123 (165)
Nm (lbf.ft) @ 1400rpm
800 (590)
Emissions:US EPA Tier 3, CARB Tier 3, EU Stage III.
Roll back fork
mm (ft-in)
QSB 6.7
Cylinders
Max torque
Parallel fork
Fork carriage width
4 stroke direct injection
Aspiration
Nett power to SAE J1349/EEC 80/1269
C
Payload**
kg (lb)
5000 (11025)
5000 (11025)
Tipping load straight
kg (lb)
8589 (18935)
8589 (18935)
Tipping load full turn (40°)
kg (lb)
7267 (16021)
7267 (16021)
Attachment weight
kg (lb)
482 (1063)
482 (1063)
**At the centre-of-gravity distance 500mm (1ft-8in). Based on 80% of full turn tipping load as defined by ISO 8313.
Manual fork spacings at 50mm increments. Fork section 100mm x 50mm (4in. x 2in.).
WHEELED LOADING SHOVEL RANGE
Max. operating weight
Max. gross engine power
kg
kW (hp)
403
406
409
411 HT
1990
5082
5924
9170
27 (36)
46 (62)
56 (75)
74 (100)
Shovel capacity
m³
0.3
0.8
1.0
1.2
Full turn tipping load
kg
–
3300
3914
5300
Payload
kg
–
1650
1957
2650
Max. breakout force
kN
20.5
41.9
53.8
73.2
Dump height @ 45°
mm
2180
2489
2619
2524
436 HT
436 HL
436 SHL
436 ZX
15935
16425
16977
16346
133 (178)
133 (178)
133 (178)
133 (178)
Max. operating weight
Max. gross engine power
kg
kW (hp)
Shovel capacity
m³
2.7
2.7
2.7
2.7
Full turn tipping load
kg
9436
7171
5841
9055
Payload
kg
4718
3585
2920
4527
Max. breakout force
kN
134
134
139
162
Dump height @ 45°
mm
2883
3537
4100
2833
WHEELED LOADING SHOVEL RANGE
411 HL
416 HT
416 SHL
426 HT
426 HL
426 ZX
9450
10008
10380
14450
14720
14105
74 (100)
97 (130)
97 (130)
123 (165)
123 (165)
123 (165)
1.2
1.4
1.40
2.1
2.1
2.1
5017
6299
4367
8271
6906
8273
2508
3150
2183
4136
3453
4136
73.2
100.4
101.4
128
128
135
2658
2606
3454
2896
3326
2914
456 HT
456 SHL
456 ZX
456 HL
21179
22079
20924
21335
160 (215)
160 (215)
160 (215)
160 (215)
3.5
3.5
3.5
3.5
12368
7978
12577
9382
6184
3989
6288
4691
143
145
154
136
3027
3993
2845
3416
436 MILITARY WHEELED LOADING SHOVEL | 436 HT
A GLOBAL COMMITMENT TO QUALITY
JCB’s total commitment to its products and customers has helped it grow from a one-man
business into Britain’s largest privately owned manufacturer of backhoe loaders, crawler excavators,
wheeled excavators, telescopic handlers, wheeled loaders, dump trucks, rough terrain fork lifts,
industrial fork lifts, mini/midi excavators, skid steer loaders, tractors and compaction equipment.
By making constant and massive investments in the latest production technology, the JCB factories
have become some of the most advanced in the world.
By leading the field in innovative research and design, extensive testing and stringent quality control,
JCB machines have become renowned all over the world for performance, value and reliability.
And with a global sales and service network of more than 650 dealers and agents, we aim to deliver
the best customer support in the industry.
Through setting the standards by which others are judged, JCB has become one of the world’s
most impressive success stories.
JCB Sales Limited, Rocester, Staffordshire ST14 5JP. Tel: 01889 590312. Fax: 01889 590588. Web: http://www.jcb.com
JCB reserves the right to change specifications without notice. Illustrations shown may include optional equipment and accessories. The JCB logo is a registered trademark of J C Bamford Excavators Ltd.
9999/5563 05/11 Issue 1
Download PDF
Similar pages