Operating manual
- GB -
High-pressure cleaners
K 2160 TS
K 2160 TS T
K 2195 TS
K 2195 TS T
K 2175 TS
K 2175 TS T
Read and conform safety instructions before use!
Keep instructions in a safe place for later use and
pass them on to any future user.
www.kraenzle.com
2
Description
Kränzle 2160 TS, 2160 TST,
Kränzle 2195 TS, 2195 TST,
Kränzle 2175 TS, 2175 TST
Ergonomically shaped handle
Cable reel with 5 m cable
Receptacle for gun with spray
lance (during breaks)
Generously dimensioned hose
drum with 15 m steel braided highpressure hose
(only available for TST models)
Hand crank (only available for TST
models)
Ergonomically shaped handle
High-pressure gun
Large stainless steel manometer
Fully adjustable pressure control
Detergent hose with filter
Interchangeable lance with Dirtkiller nozzle
Interchangeable washing lance
On/Off switch with signal lamp and motor
protection
Receptacle for high-pressure gun
Receptacle for Dirtkiller and lance
Generously dimensioned trolley
suited for difficult terrain and stairs
Contents
Page
3
Description ........................................................................................... 2
Contents
........................................................................................... 3
Technical data . ....................................................................................... 4
Overview “This is what you have purchased” . .......................................... 6
General rules .......................................................................................... 7
Safety precautions – accident prevention ................................................. 8
Extremely important: Water connection – electrical connection .............. 10
Kränzle- technology .................................................................................. 12
Water and cleaning system ................................................ 12
Lance and spray gun . ........................................................ 12
Pressure control valve – safety valve . ................................ 12
Motor protecting switch ...................................................... 13
High pressure hose and spray device ........................................ 13
Total stop system . ............................................................. 13
Putting into operation ......................................................................... 14
Connection to water mains ................................................. 14
Direct suction .................................................................... 17
When using detergents ...................................................... 18
To shut down the pump / frost protection . .............................................. 19
Small repairs – do it yourself! ................................................................ 20
Inspections – inspection reports . ........................................................... 24
EG – Declaration of Conformity ............................................................. 26
Guarantee ......................................................................................... 27
Accessories for high-pressure cleaners .................................................. 28
Spare parts list . .................................................................................. 30
Complete assembly . .......................................................... 30
Valve housing .................................................................... 32
Unloader valve and pressure switch ................................... 34
Motor ................................................................................ 36
Transmission ..................................................................... 38
Hose drum . ....................................................................... 39
Gun with lance . ................................................................. 40
Dirtkiller with lance ............................................................ 41
Wiring diagrams .................................................................................... 43
Technical data
Kränzle Kränzle
2160 TS 2160 TS T
Kränzle Kränzle
2195 TS 2195 TS T
Operating press. fully adjustable 30 - 140 bar 30 - 180 bar
Nozzle size 25042 25030
Permissible overpressure 160 bar 195 bar
Water outputat 1,400 r.p.m. 11 l/min
at 1,400 r.p.m. 8 l/min
Water inlet temperature max. 60 °C max. 60 °C
Suction height
2.5 m
2.5 m
Hose drum
no
yes
no
yes
Steel braided high-pressure hose
10 m
15 m
10 m
15 m
Detergent suction
yes
yes
Connected load230 V~ 50 Hz, 14 A230 V~ 50 Hz, 14 A
Power input P 1 - 3.2 kW P 1 - 3.2 kW
Power output P 2 - 2.4 kW P 2 - 2.4 kW
Weight
37 kg 39,5 kg
37 kg 39.5 kg
Dim. incl. pulling handle in mm900 x 375 x 360900 x 375 x 360
Sound level acc. to DIN 45 635 78 dB (A) 81 dB (A)
Sound level with Dirtkiller 82 dB (A) 78 dB (A)
Acoustic power LWA 89 dB (A) 91 dB (A)
Recoil at lanceapprox. 25 Napprox. 25 N
Vibration at lance
2.0 m/s2 2.0 m/s2
Permissible tolerance for figures ± 5 % acc. to VDMA uniform sheet 24411
4
Kränzle 2175 TS Kränzle 2175 TS T
Operating press. fully adjustable
Nozzle size
Permissible overpressure
Water output Water inlet temperature
Suction height
Hose drum
Steel braided high-pressure hose
Detergent suction
Connected load
Power input
Power output
Weight
Dim. incl. pulling handle in mm
Sound level acc. to DIN 45 635
Sound level with Dirtkiller
Acoustic power LWA
Recoil at lance
Vibration at lance
30 - 160 bar
25042
175 bar
at 1,400 r.p.m. 12 l/min
max. 60 °C
2.5 m
no
10 m
yes
400 V~ 50 Hz, 6,7 A
P 1 - 3.3 kW
P 2 - 2.6 kW
37 kg
900 x 375 x 360
78 dB (A)
82 dB (A)
91 dB (A)
approx. 27 N
2.1 m/s2
30 - 160 bar
25042
175 bar
at 1.400 r.p.m. 12 l/min
max. 60 °C
2.5 m
yes
15 m
yes
400 V~ 50 Hz, 6,7 A
P 1 - 3.3 kW
P 2 - 2.6 kW
39,5 kg
900 x 375 x 360
78 dB (A)
82 dB (A)
91 dB (A)
approx. 27 N
2.1 m/s2
Permissible tolerance for figures ± 5 % acc. to VDMA uniform sheet 24411
5
6
This is what you have purchased
1. Kränzle high-pressure cleaners
2160 TST, 2195 TST, 2175 TST with 15 m
steel braided high-pressure hose and hose
drum NW 6
or
Kränzle high-pressure cleaners 2160 TS,
2195 TS, 2175 TS with 10 m steel braided
high-pressure hose but without hose drum
NW 6
2. Trigger gun with safety catch, insulated
handle and screw connection
3. Dirtkiller lance with stainless steel pipe
4. Vario-Jet lance with stainless steel pipe
5. Handle with fixing screw for hose drum
6. Operating manual
General rules
7
Range of application
Use machines for cleaning tasks with high-pressure water jet and detergents or with
high-pressure water jet without detergents only.
Inspections
The machine must be inspected according to the “Guidelines for Liquid Spray Devices”
at least once every 12 months by a qualified person, to ensure that continued safe
operation is guaranteed. The results of the inspection are to be recorded in writing.
This may be done in any form. For inspection reports see pages 22 - 25.
High-pressure cleaners used for commercial purposes have to
be checked by a qualified person at least every 12 months!
Accident prevention
The machine is designed for accidents to be impossible if used correctly.The operator is
to be notified of the risk of injury from hot machine parts and the high pressure water jet.
The “Guidelines for Liquid Spray Devices” must be complied with. (see pages 8 and 9).
Oil change:
The first oil change should be carried out after approximately 50 operating hours,
then every year or after 1000 operating hours. If the oil turns grey or white, you must
change the oil of your high pressure pump in any case.
Put the machine into a horizontal position, then open the oil discharge screw at the
bottom of the device over a collection reservoir. The oil is to be caught in the reservoir
and disposed of in an approved manner.
New oil: 0,35 l - Motor oil W 15/40.
Oil leakage: If oil leaks contact your nearest after-sales
service (dealer) at once. (Ecological damage, damage to
the transmission)
In case of increased humidity or fluctuations in
temperature development of condensed water is
possible; if the oil turns grey, you must change it.
8
Safety precautions
Bear in mind that during cleaning tasks
with a high-pressure water jet a significant
recoil at the lance arises (see technical
data on page 4).
Apply the safety catch on the trigger
gun after each use, in order to prevent
unintentional spraying!
Always aim the underbody lance! Bear
in mind when using a curved or angled
spraying lance that there is a significant
amount of torque in the recoil!
Safety precautions - That`s forbidden!
9
Never direct the water jet at people
or animals!
Only use power cables which are
in perfect working order! Do not
damage the power cable or repair it
incorrectly!
Never pull the high pressure hose
if it has formed kinks or “nooses”!
Never pull the hose over sharp
edges!
Never allow children to use the
high pressure cleaner!
Never direct the water jet at the
machine itself!
Never direct the water jet at a
power socket!
10
Please note - important!
Lack of water
Lack of water occurs more often than you
probably believe. The more powerful a
high-cleaner is the greater is the danger
that a lack of water occurs. If there is only
an insufficient amount of water available,
cavitation arises inside the pump, which is
normally noticed too late or even not at all.
The pump will be destroyed!
Please check the available quantity of
water by filling a bucket with litre scale for
one minute.
The following minimum quantity of water is necessary for a safe and problem-free
operation of the high-pressure cleaner:
Kränzle 2160 TS / TS T: 11 l/min
Kränzle 2195 TS / TS T: 8 l/min
Kränzle 2175 TS / TS T: 12 l/min
If the metered quantity of water is too small, you have to use a different
water connection, guaranteeing the necessary output.
Lack of water leads to an accelerated wear of the joints (no guarantee).
Connection to water supply
Please pay attention to the regulations of your waterworks company! In accordance
with DIN EN 61770, the machine may not be directly connected to the public drinking
water supply lines. A brief connection however is permissible according to DVGW
(German Association for Gas and Water Affairs) if a tube ventilator with check valve
(Kränzle Order-No. 41.016 4) is built into the water supply. Also indirect connection
to the public drinking water supply lines is permissible by way of free emission in
accordance with EN 61 770; e.g. by using a reservoir with a float valve.
Direct connection to a non-drinking water supply line is permissible.
11
Insufficient quantity of electricity
If there are too many collectors in your
proximity connected to the network at
the same time, the available voltage
and the current intensity may decline.
Consequently the motor of the
high-pressure cleaner does not start or
even blows.
The power supply may also be insufficient
if the power cable is too long or too
thin. If extension cables are too long,
this may lead to a voltage drop causing
malfunctions or start-up difficulties.
Connected load:
Kränzle 2160 TS / TS T: 230 V ~, 50 Hz
Kränzle 2195 TS / TS T: 230 V ~, 50 Hz
Kränzle 2175 TS / TS T: 400 V, 50 Hz (phase-sequence not significant)
Check the line fusing and have the voltage and the available current
intensity checked by an expert in case of uncertainty.
Electrical connection
The machine is supplied with an electrical power cable with plug. The mains plug must
be fitted to a standard grounded socket with a 30mA residual current operated device.
The socket must be protected with a 16A delay action fuse on the mains side. When
using an extension cable, this must have an earthed lead which is properly connected to
the socket. The conductors in the extension cable must have a minimum cross section of
1.5 mm². Plug connections must be of a spray-proof design, and may not be located on
a wet floor. With extension cables of more than 10 m the minimum cross section must be
2.5 mm! When using a cable drum, always keep the cable wound as far as possible.
12
Kränzle technology
Water and Cleaning System
Water can be connected at mains pressure to the high pressure pump or it can be
sucked directly from a storage tank. The water is then forced under pressure by the high
pressure pump to the lance. The high pressure jet is formed by the nozzle at the end of
the lance.
Environmental, refuse disposal and water protection
regulations must be observed!
Lance with trigger gun
The machine can only be operated when the safety trigger is squeezed. When the
lever is squeezed, the spray gun opens. The liquid is then pumped to the nozzle. The
spray pressure increases and quickly reaches the selected operating pressure. When
the trigger is released, the trigger gun closes and any further spraying of liquid from the
lance is stopped. The pressure gauge must show 0 bar.
The increase in pressure when the trigger gun is closed causes the pressure control
valve-safety valve to open. The motor is switched off by the pressure switch. When
the trigger gun is opened, the pressure control valve - safety valve closes, the motor
is started and the pump resumes pressure spraying from the lance with the selected
operating pressure.
The trigger gun is a safety device. Repairs should only
be performed by qualified persons. Should replacement
parts be required, use only components authorized by
the manufacturer.
Pressure control valve - safety valve
The pressure control valve - safety valve protects the machine from a build up of
excess pressure, and is designed not to permit an excess pressure to be selected for
operation. The limit nut on the handle is sealed with a spray coating. The operating
pressure and spray rate can be steplessly adjusted by turning the handle.
Replacements, repairs, new adjustments and sealing
should only be performed by qualified persons.
13
Motor protection switch
The motor is protected from overload by a motor protection switch, which cuts out the
motor in the event of overload. However should the switch trip frequently, the cause of
the malfunction should be located and rectified (see page 11).
Replacements and inspection work should only be performed
by qualified persons when the machine is disconnected from
the power supply, i.e. with plug pulled out from the electrical
socket.
High pressure hose and spray device
The high pressure hose and spraying device supplied with the machine are made of high
grade material, they are also optimised for the machine and marked as required by the
appropriate regulations.
If replacement parts are required, only such parts that are
authorised by the manufacturer and which bear the markings
required by the appropriate regulations may be used. The
high pressure hose and spray device must be connected in
a pressure-tight manner. The high pressure hose may not be
driven over, pulled excessively, or twisted. The hose may under
no circumstances be pulled over sharp edges, since otherwise
the guarantee is automatically void.
Total stop system
The new Kränzle K2160 / K2195 / K2175 are equipped with an electrical Start/Stop
control. Having connected the high-pressure cleaner to the water supply and having
connected the HP hose, switch the machine “on” using the On/Off switch. A red light in
the switch flashes.
The motor is started by opening the gun. The motor is switched off after the gun has
been closed. The high-pressure cleaner works in stand-by until the On/Off switch is
switched to “Off”. The red light in the switch goes out.
Having switched off the machine shortly press the trigger to release the pressure to be
able to unfasten the HP hose.
14
Putting into operation
1. Move high-pressure cleaner to the
job site.
The Kränzle 2160 / 2195 / 2175 are
movable machines with sturdy trolleys
ideally suited for difficult terrain and stairs.
Setting up – Location
Never pull the machine if the water
supply hose is still connected!
Neither set up or operate the machine in rooms where there
is a risk of fire or explosion nor put it into puddles. Do not
use the machine under water.
2. Check water inlet filter for
cleanliness prior to putting the machine
into operation!
Manually unscrew hose attachment. Take
out the serial water inlet filter using needle
nose pliers and clean if filter is soiled.
3. Each time check oil level at the oil
dipstick prior to putting the HP cleaner
into operation. (Take care that cleaner is
in horizontal position!)
The oil level must show between the two
markings.
4. Put up machine. Release fixing screw
from hexagonal base of hose drum, put
tiltable handle onto the hexagonal base
and fix with screw.
15
5. Push on lance or Dirtkiller lance to gun.
6. Screw together lance and gun.
7. Push on HP hose to gun.
8. Screw together HP hose and gun.
9. Put HP cleaner into horizontal position.
These machines must be operated in
horizontal position! Unwind HP hose
from hose drum without kinks and nooses.
10. Connect water hose to water tank.
The cleaner may be connected to water
mains with cold or 60°C warm water.
Alternatively water can be sucked in from
a container (see page 17).
Be careful when using hot water!
When running your high pressure cleaner with hot water
of 60° C raised temperatures occur. Do not touch the
metal parts of the cleaner without safety gloves!
16
Putting into operation
11. Connect to circuit.
Kränzle 2160 TS / TS T: 230 Volt, 50 Hz.
Kränzle 2195 TS / TS T: 230 Volt, 50 Hz.
Kränzle 2175 TS / TS T: 400 Volt, 50 Hz.
The socket must be protected with a 16A
delay action fuse on the mains side.
12. Steplessly adjust operating pressure
with handwheel. The maximum pressure is
adjusted ex work.
13. Ventilation of the machine: Pull and
release the trigger several times.
Switch on high-pressure cleaner with
opened spray gun. Start cleaning task.
17
Direct suction
Due the suction capacity of its pump (up to 2.5 m suction height, max. hose length 3 m)
this high-pressure cleaner can suck in water for cleaning purposes from separate
containers or ponds.
Prior to starting the first suction the pump resp. the
suction hose has to be filled with water!
1. Mount suction hose with suction filter
(Kränzle accessories No. 15.038 3). When
using other hoses the inner cross section
of the hose must be at least 3/4” = 16 mm.
2. Fill suction hose with water.
3. Put filled suction hose into the
container and start the cleaning job.
Use clean water only!
Never suck in water containing
chlorine.
Note
F
Depending on the water quality it may occur after a prolonged standstill that the valves
get sticky. Consequently the machine cannot properly suck in water from a container.
In this case connect a hose with pressurized water to the pump inlet. Having started the
machine the pressurized water opens the valves and the machine resumes sucking in
water from the container. Now you can carry on with your cleaning task as usual.
18
Suction of detergents
with detergent supply:
For the Kränzle 2160 TS / TS T, 2195 TS / TS T and 2175 TS / TS T a built-in injector
provides the facility to suck in detergents.
By pushing the Vario-Jet nozzle to the front the machine is adjusted to low pressure
and a vaccum is build up in the injector. Thus the detergent can be sucked in via the
connected suction hose with filter.
1. Place chemicals filter into container
with cleansing agent.
2. To reach the low pressure push Vario
nozzle to the front so that the injector can
suck in the cleansing agent.
3. The chemicals supply is automatically
stopped when closing the Vario nozzle by
pushing it backwards.
Let cleansing agent take effect and then
spray off with a high-pressure jet.
The pH value neutral 7-9 is prescribed for the detergents.
Only use detergents suitable for high-pressure cleaners.
Observe specifications of detergent manufacturer!
e.g.: protective equpment, rules for waste water treatment
etc.
Never suck in liquids containing solvents like varnish
solvents, petrol, oil or similar liquid! Observe specifications
of detergent manufacturers! Seals inside the appliance are
no resistant against solvents! The spray mist of solvents is
highly inflammable, explosive and poisonous.
To shut down the pump
19
01. Switch off the machine
02. Cut off the water supply
03. Open the spray gun briefly until the pressure is released
04. Apply the safety catch on the spray gun
05. Remove the water hose and spray gun
06. Drain the pump: switch on the motor for approx. 20 seconds
07. Pull the plug from the socket
08. Clean HP hose and wind up
09. Clean power cable and wind up
10. Clean water filter
11. Winter: store the pump in rooms above 0°C
Store in a place-saving manner
Due to their compact and space saving
design these Kränzle-2000 cleaners can
be stored practically anywhere.
20
Small repairs -
do it yourself!
No water from the nozzle but the gauge shows full pressure:
Most likely the nozzle is blocked.
The pressure gauge shows full pressure,
but from the nozzle comes only little water
or no water at all.
(Inside the pressure gauge is no water but
a filling with glycol to damp the vibration of
the pointer.)
Switch off the cleaner. Pull plug from
the socket. Operate gun seveal times to
decrease the pressure.
First unscrew gun and lance, then rinse
hose from any residues.
Check water inlet filter for soiling.
If the problem still exists, take wire (paper
clip) and push through nozzle opening.
If this procedure is not successful, the nozzle has to be dismantled and cleaned or even
replaced, if necessary.
CAUTION! Pull plug from socket prior to starting
any repair work!
21
Pressure gauge shows little pressure, the water from the nozzle comes
in squirts: Most likely the valves are soiled or sticky.
The pressure gauge shows little
pressure despite fully turned up pressure
regulation. The water from the lance
comes in squirts. The HP hose vibrates.
(Inside the pressure gauge is no water but
a filling with glycol to damp the vibration of
the pointer.)
Unscrew all 6 valves, one after the other
(hexagonal brass screws, 3 in a row,
vertically and horizontally)
Take out valve body (with green or red
plastic coating) and O-ring by means
of needle nose pliers. Check O-ring for
damage. In case of a damage the O-ring
has to be replaced.
Take a wire (paper clip) and clean valves
under running water. Also clean valve seat
inside the pump.
Do not forget the O-ring during
reassembly!
22
Small repairs -
do it yourself!
The pressure gauge shows full pressure although the gun has
been closed. The pressure switch valve switches constantly.
Possible cause no.1: Leakage
Having closed th gun, the HP cleaner must
shut down and the pressure gauge must
show „0“ bar.
If the pressure gauge still shows full
pressure and the motor constantly
switches on and off, the possible reason
for this can be a leakage of the pump, the
HP hose or the lance.
Proceeding:
Check the connections from the HP cleaner to the the HP hose, from the hose to
the gun and also the connection between
lance and gun for tightness.
Switch off the cleaner. Shortly pull the trigger of the gun to decrease the
pressure.
Unscrew HP hose, gun and lance and
check the O-rings.
If the O-rings are damaged they have to
be replaced.
Caution! In case of a leakage there is no guarantee for
possible consequential damages.
23
The pressure gauge shows full pressure although the gun has
been closed. The pressure switch valve switches constantly.
Possible cause no. 2: The return body is soiled
or the sealing ring on the return body is defective.
Unscrew pump outlet.
Take out check ball and check for soiling
or damage of ball or stainless steel seat
inside the pump housing.
Replace non-return valve if necessary.
Caution ! There is no guarantee if the pump is damaged
by defective O-rings due to air induction or lack of water
(cavitation).
24
Inspection report for HP cleaners
HP cleaners for industrial use have to be checked by an expert every 12 months!
Inspection report on annually carried out Labour Safety Inspection (UVV) according to
the Guidelines for Liquid Spray Equipment. (This inspection sheet serves as proof for
the completion of the retest and must be kept carefully!) Kränzle test seals: Order no. UVV200106
Owner:
Address:
Scope of inspection
Type:
Serial no.:
Rep. order no.:
o.k.
yes
no repaired
Type plate (on hand)
Operating manual (on hand)
Protective covering, -device
Pressure line (tightness)
Pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
HP-hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding of operating pr.
Power cable (damage)
Protective conductor (connected)
On / Off switch
Used chemicals
Allowed chemicals
Inspection data
determined value
set value
High-prsure nozzle
Operating pressure..................bar
Switch off pressure................bar
Conductor reist. not exceeded / value
Insulation
Leakage current
Gun locked
Inspection result (tick)
The appliance was checked by an expert according to the Guidelines for Liquid
Spray Equipment, the defects found have been rectified so that the Labour Safety can
be confirmed.
The appliance was checked by an expert according to the Guidelines for Liquid
Spray Equipment. The Labour Safety cannot be confirmed unless the defects found are
rectified by repair or replacement of the faulty parts
The next retest according to the Guidelines for Liquid Spray Equipment has to be carried
out by: Month
Year
Place, date
Signature
25
Inspection report for HP cleaners
HP cleaners for industrial use have to be checked by an expert every 12 months!
Inspection report on annually carried out Labour Safety Inspection (UVV) according to
the Guidelines for Liquid Spray Equipment. (This inspection sheet serves as proof for
the completion of the retest and must be kept carefully!) Kränzle test seals: Order no. UVV200106
Owner:
Address:
Scope of inspection
Type:
Serial no.:
Rep. order no.:
o.k.
yes
no repaired
Type plate (on hand)
Operating manual (on hand)
Protective covering, -device
Pressure line (tightness)
Pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
HP-hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding of operating pr.
Power cable (damage)
Protective conductor (connected)
On / Off switch
Used chemicals
Allowed chemicals
Inspection data
determined value
set value
High-prsure nozzle
Operating pressure..................bar
Switch off pressure................bar
Conductor reist. not exceeded / value
Insulation
Leakage current
Gun locked
Inspection result (tick)
The appliance was checked by an expert according to the Guidelines for Liquid
Spray Equipment, the defects found have been rectified so that the Labour Safety can
be confirmed.
The appliance was checked by an expert according to the Guidelines for Liquid
Spray Equipment. The Labour Safety cannot be confirmed unless the defects found are
rectified by repair or replacement of the faulty parts
The next retest according to the Guidelines for Liquid Spray Equipment has to be carried
out by: Month
Year
Place, date
Signature
26
EC declaration of conformity
Hereby we declare that:
Kränzle 2160 TS / TS T,
Kränzle 2195 TS / TS T,
Kränzle 2175 TS / TS T,
technical specifications available from:
Manfred Bauer, Fa. Josef Kränzle
Rudolf-Diesel-Str. 20, 89257 Illertissen
K 2160 TS / TS T: 660 l/h
K 2195 TS / TS T: 480 l/h
K 2175 TS / TS T: 720 l/h
machinery directive 2006/42/EEC, EMC-directive 2004/108 EEC, noise directive 2005/88/EC, Art. 13, HP water spraying machines annex 3, part B, chapter 27
Nominal flow
comply with the following guidelines
and their amendments for high-pressure
cleaners:
Sound level measured:
Kränzle 2160 TS / TS T: 87 dB (A)
Kränzle 2195 TS / TS T: 87 dB (A)
Kränzle 2175 TS / TS T: 89 dB (A)
Sound level guaranteed:
Kränzle 2160 TS / TS T: 89 dB (A)
Kränzle 2195 TS / TS T: 89 dB (A)
Kränzle 2175 TS / TS T: 91 dB (A)
Applied conformity evaluation procedures
annex V, noise directive 2005/88/EC
Applied specifications and standards:
EN 60 335-2-79 :2004
EN 55 014-1 :2006
EN 61 000-3-2 :2006
EN 61 000-3-3 :2008
I. Kränzle GmbH
Elpke 97 D - 33605 Bielefeld
Bielefeld, 03.09.2012
Kränzle Josef
(Managing director)
Guarantee
27
The guarantee is only valid for material and manufacturing errors.
Wearing does not fall within this gurantee.
The instructions in our operating manual must be complied with..
The operating instructions form part of the guarantee. The Guarantee is void if other parts
are used than genuine Kränzle accessory parts or genuine Kränzle spare parts.
For high-pressure cleaners sold to the user the guarantee period is 24 month.
For high-pressure cleaners sold for industrial use the guarantee period is 12 month.
In the case of a guarantee please contact your dealer or authorized seller delivering
accessories and your purchase receipt. You can fin them in the internet under
www.kraenzle.com.
The guarantee is also void if the machine is used with exceeding the temperature and
speed limits, a voltage below the required rating, with less than the required amount of
water or with dirty water.
Pressure gauge, nozzle, valves, sleeves, high pressure hose and spray equipment are
wear parts and are not covered by the warranty.
28
Versatile due to Kränzle accessories
Rotating washing brush with 400 mm
extension, Order no. 41 050 1
Underbody lance with 800 mm extension,
Order no. 41 075
Pipe cleaning hose with nozzle,
10 m - Order no. 41 058 1
20 m - Order no. 41 058 2
25 m - Order no. 41 058 3
30 m - Order no. 41 058 4
29
Sludge sucker, stainless steel,
Order no. 41 801
Sludge sucker with 3 m suction hose,
Order no. 41 104
Floor cleaner round cleaner UFO
Order no. 41.850
Sand blasting set compl. up to 12 l/min, 150 bar
Order no. 41 068 1
Sand blasting set compl. up to bis 19 l/min, 250
bar Order no. 41 068
30
Spare parts list
Kränzle 2160 / 2195 / 2175
31
Complete assembly
No
Description
1
1.1
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17.1
17.2
17.3
17.4
17.5
17.6
18
19
28
29
30
31.1
Motor-Pumpen-Einheit mit Elektrik
K 2160 TS
K 2160 TS T
K 2195 TS
K 2195 TS T
K 2175 TS
K 2175 TS T
Motor-Pumpen-Einheit ohne Elektrik
K 2160 TS
K 2160 TS T
K 2195 TS
K 2195 TS T
K 2175 TS
K 2175 TS T
Fahrgestell
Versteifungsblech
Schraube 6,0 x 30
Schraube M 8 x 12
Achshalter
Schraube M 6 x 40
Standfuß links + rechts
Käfigmutter M6
Schraube 5,0 x 30
Rad d210mm
Scheibe 40 x 6 x 1,5 (Stahl)
31.2
32.1
32.2
Kunststoffsenkschraube 5,0 x 20
Radkappe
Gummipuffer 20 x 25
Frontplatte „K 2160 TS“
Frontplatte „K 2160 TS T“
Frontplatte „K 2195 TS“
Frontplatte „K 2195 TS T“
Frontplatte „K 2175 TS“
Frontplatte „K 2175 TS T“
Knickschutz
Schraube 5,0 x 14
O-Ring 9,3 x 2,4
Hochdruckschlauch NW 6 10 m (TS-Geräte)
Pistole M2000
Vario-Jet 03 mit Lanze 500 mm
für K 2195 TS / TST
Vario-Jet 042 mit Lanze 500 mm
für K 2160 TS / TST + K 2175 TS / TST
Schmutz-Killer 03 mit Lanze 500 mm
für K 2195 TS / TST
Schmutz-Killer 042 mit Lanze 500 mm für K 2160 TS / TST + K 2175 TS / TST
Qty.
Ord.-No
1
1
1
1
1
1
48.060
48.061
48.062
48.063
48.064
48.065
1
1
1
1
1
1
1
1
6
4
1
2
1
2
2
2
2
48.060 1
48.061 1
48.062 1
48.063 1
48.064 1
48.065 1
48.000
48.010
43.423
40.122
48.003
48.012
48.005
48.011
43.418
44.538
45.216 7
2
45.421 1
1
41.156 8-042
1
41.570-03
1
41.570-042
2
2
1
1
1
1
1
1
1
2
2
1
1
1
46.011
48.013
48.002 1
48.002 2
48.002 3
48.002 4
48.002 5
48.002 6
48.004
43.426
13.273
43.416
12.480
41.156 8-03
32
Spare parts list
Kränzle 2160 / 2175
33
Valve housing 18mm
No
Description
1
2
2.1
3
4
5
6
7
8
8.1
9
10
11
12
13
14
15
16
17
27
28
28.1
29
30
31
32
33
34
37
38
39
40
41
42
43
44
46
47
48
49
50
Ventilgehäuse
Ventilstopfen
Ventilstopfen mit R1/4“ IG
Dichtstopfen M 10 x 1
Ventile (grün) für APG-Pumpe
O-Ring 16 x 2
O-Ring 15 x 2
Dichtstopfen R1/4” mit Bund
Ausgangsteil (TST)
Ausgangsteil (TS)
Dichtstopfen M 8 x 1
O-Ring 18 x 2
Aluminium - Dichtring
Verschraubung Ermeto R1/4” x 8
O-Ring 11 x 1,5
Edelstahlsitz Ø 7
Sprengring
Edelstahlkugel Ø10
Rückschlagfeder „K“
Druckring
Manschette 18 x 26 x 4/2
Gewebemanschette 18 x 26 x 4/2
Backring 18 x 26
O-Ring 28,3 x 1,78
Leckagering 18 mm
Zwischenring 18 mm
Verschlussstopfen R3/8“
Kupferring 17 x 22 x 1,5
Verschlussschraube M10x1
O-Ring 6x1,5
Saugzapfen Schlauchanschluss
Edelstahlkugel 5,5 mm
Edelstahlfeder
Kupferring 14 x 20 x 1,5
Innensechskantschraube M 8 x 30
Innensechskantschraube M 8 x 55
Sauganschluß
Wasserfilter
Gummi Dichtring
Steckkupplung
O-Ring
Qty.
Ord.-No
1
5
1
1
6
6
6
1
1
1
2
1
3
1
1
1
1
1
1
3
3
3
6
3
3
3
1
1
1
2
1
1
1
1
2
2
1
1
1
1
1
42.160 3
41.714
42.102
43.043
41.715 1
13.150
41.716
42.103
40.522
40.522 2
13.158
43.446
13.275
41.042
12.256
14.118
12.258
12.122
14.120 1
41.018
41.013
41.013 1
41.014
40.026
41.066
41.015 2
14.113
40.019
13.385
13.386
13.236
13.238
13.239
42.104
41.036 1
41.017 1
41.016
41.046 2
41.047 1
41.047 4
41.047 3
Reparatur-Sätze:
Reparatursatz Manschetten 18 mm
bestehend aus je
3 x Pos. 27, 3 x Pos. 28; 3 x Pos. 28.1; 6 x Pos. 29; 3 x Pos. 30
Reparatursatz Ventile für APG-Pumpe
bestehend aus je 6 x Pos. 4; 6 x Pos. 5; 6 x Pos. 6
41.049 1
41.748 1
34
Spare parts list
Kränzle 2195
35
Valve housing 15mm
No
Description
1
2
2.1
3
4
5
6
7
8
8.1
9
10
11
12
13
14
15
15
17
27
28
28.1
29
30
31
32
33
34
37
38
39
40
41
42
43
44
46
47
48
49
50
Ventilgehäuse
Ventilstopfen
Ventilstopfen mit R1/4“ IG
Dichtstopfen M 10 x 1
Ventile (grün) für APG-Pumpe
O-Ring 16 x 2
O-Ring 15 x 2
Dichtstopfen R1/4” mit Bund
Ausgangsteil (TST)
Ausgangsteil (TS)
Dichtstopfen M 8 x 1
O-Ring 18 x 2
Aluminium - Dichtring
Verschraubung Ermeto R1/4” x 8
O-Ring 11 x 1,5
Edelstahlsitz Ø 7
Sprengring
Edelstahlkugel Ø10
Rückschlagfeder „K“
Stützring rot 15mm
Manschette weich 15mm
Manschette Gewebe 15mm
Backring 15 x 24
O-Ring 28,3 x 1,78
Leckagering 15 mm
Zwischenring 15 mm
Verschlussstopfen R3/8“
Kupferring 17 x 22 x 1,5
Verschlussschraube M10x1
O-Ring 6x1,5
Saugzapfen Schlauchanschluss
Edelstahlkugel 5,5 mm
Edelstahlfeder
Kupferring 14 x 20 x 1,5
Innensechskantschraube M 8 x 30
Innensechskantschraube M 8 x 55
Sauganschluss
Wasserfilter
Gummi Dichtring
Steckkupplung
O-Ring
Qty.
Ord.-No
1
5
1
1
6
6
6
1
1
1
2
1
3
1
1
1
1
1
1
3
3
3
6
3
3
3
1
1
1
2
1
1
1
1
2
2
1
1
1
1
1
42.163 3
41.714
42.102
43.043
41.715 1
13.150
41.716
42.103
40.522
40.522 2
13.158
43.446
13.275
41.042
12.256
14.118
13.147
12.122
14.120 1
42.913
42.902
42.902 1
42.903
40.026
42.905
42.904 1
14.113
40.019
13.385
13.386
13.236
13.238
13.239
42.104
41.036 1
41.017 1
41.016
41.046 2
41.047 1
41.047 4
41.047 3
Reparatur-Sätze:
Reparatursatz Manschetten 15 mm
bestehend aus je
3 x Pos. 27; 3 x Pos. 28; 3 x Pos. 28.1; 6 x Pos. 29; 3 x Pos. 30
Reparatursatz Ventile für APG-Pumpe
bestehend aus je 6 x Pos. 4; 6 x Pos. 5; 6 x Pos. 6
42.911
41.748 1
36
Spare parts list
Kränzle 2160 / 2195 / 2175
No
Description
Qty.
70
71
72
73.1
73.2
73.3
73.4
Steuerkolben kpl. mit Handrad Rep.- Satz Druckschaltermechanik Druckschalter kpl. Ventilgehäuse kpl. ohne Manometer (K2160 TS, K2175 TS)
Ventilgehäuse kpl. ohne Manometer (K2160 TST, K2175 TST)
Ventilgehäuse kpl. ohne Manometer (K2195 TS)
Ventilgehäuse kpl. ohne Manometer (K2195 TST)
40.490
15.009 3
41.300 6
48.050
48.050 1
48.051
48.051 1
Ord.-No
37
Unloader valve and pressure switch
No
Description
5
5.1
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
40
42
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
O-Ring 16 x 2
O-Ring 13,94 x 2,62
O-Ring 11 x 1,44
Edelstahlsitz
Sicherungsring
Edelstahlkugel
Edelstahlfeder
Verschlussschraube
Steuerkolben
Parbaks 16 mm
Parbaks 8 mm
Spanstift
Kolbenführung spezial
Kontermutter M 8 x 1
Ventilfeder schwarz
Federdruckscheibe
Nadellager
Handrad AM-Pumpe
Kappe Handrad AM-Pumpe
Elastic-Stop-Mutter M 8 x 1
Manometer 0-250 Bar
Aluminium-Dichtring Sechskant - Mutter M 4 Druckfeder 1 x 8,6 x 30
O-Ring 3,3 x 2,4
Führungsteil Steuerstößel
O-Ring 13 x 2,6
O-Ring 14 x 2
Parbaks 4mm
Stützscheibe
Edelstahlfeder
Steuerstößel
Parbaks 7mm
Stopfen M 10 x 1 (durchgebohrt)
Gehäuse Elektroschalter
Gummimanschette PG 9
Scheibe PG 9
Verschraubung PG 9
Kabel 2x 1,5 mm²
Blechschraube 2,8 x 16
Deckel Elektroschalter
O-Ring 44 x 2,5
Mikroschalter
Zylinderschraube M 4 x 22
Qty.
Ord.-No
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
6
1
1
1
2
13.150
42.167
12.256
14.118
13.147
13.148
14.119
14.113
14.134
13.159
14.123
14.148
42.105
14.144
14.125
14.126
14.146
40.457
40.458
14.152
15.039
13.275
12.138
40.520
12.136
15.009 1
15.017
43.445
12.136 2
15.015 1
15.016
15.010 2
15.013
13.385 1
15.007
15.020
15.021
15.022
15.019 1
15.024
15.008
15.023
15.018
15.025
38
Spare parts list
Kränzle 2160 / 2195 / 2175
39
Motor
No
Description
1
3
4
5
6
8
9
10
11
12
13
15
16
20
21
22
23
24
25
27
28
29
30
31
32
Ölgehäuse für AP mit Deckel und Dichtung
Rotor mit Motorwelle
Passfeder 6 x 6 x 20
Motor-Lager B-Seite 6205 - 2Z
Motor-Lager Schulterlager 7304
Öldichtung 25 x 35 x 7
Lüfterrad BG 90
Lüfterhaube BG 90
Flachdichtung
Innensechskantschraube M 6 x 30
Schelle für Lüfterrad mit Schrauben
Schraube M 4 x 12
Erdungsschraube kpl.
Schaltkasten
Deckel für Schaltkasten
Klemmrahmen mit Schalterabdichtung
Blechschraube 3,5 x 9,5
Dichtung für Deckel
Schraube 5,0 x 20
Kabelverschraubung PG 13,5
Gegenmutter für PG 13,5
Kabelverschraubung PG 11
Gegenmutter für PG 11
Lüsterklemme 3-polig
Schraube 3,5 x 20
Kränzle 2160 TS / TST, 2195 TS / TST:
2.1
Motorgehäuse mit Stator Wechselstrom
14.1
Kabel mit Stecker (Schuko)
18
Kondensator 70 µF
26.1
Schalter mit 14,5 A
40.1
41.1
Ord.-No
1
1
1
1
1
1
1
1
1
4
1
10
1
1
1
1
2
1
4
1
1
1
1
1
1
46.530 2
43.316
41.483 1
43.317
41.027
41.024
43.319
43.320
43.030
43.037
43.454
41.489
43.038
48.001
44.512 1
43.453
41.088
44.522
43.018
40.539
44.253
41.419
44.521
43.326
43.415
1
1
1
1
43.826
41.092
43.322
41.111 6
Schaltkasten Wechselstrom kpl. Pos. 18 – 32
Motor Wechselstrom kpl. ohne Schalter Pos. 1 - 16
Kränzle 2175 TS / TST:
2.2
Motorgehäuse mit Stator Drehstrom
14.2
Kabel mit Stecker (CE-KON)
26.2
Schalter mit 8 A
33
Schütz 3x400V 50/60 Hz
34
Schraube 3,9 x 13
40.2
41.2
Qty.
48.052
48.054
1
1
1
1
3
43.827
43.828
41.751
48.016
41.078
Schaltkasten Drehstrom kpl. Pos. 20 – 34
Motor Drehstrom kpl. ohne Schalter Pos. 1 - 16
48.053
48.055
40 Transmission
No
Description
1
2
3
4
5
6
7
8
8.1
10
12
14
15
16
17
18
20
Gehäuseplatte für 18 mm Plunger
Öldichtung 18 x 28 x 7
O-Ring Viton 88 x 2
Plungerfeder
Federdruckscheibe 18 mm
Plunger 18 mm
Sprengring 18 mm
Taumelscheibe 12,0° (K2160 TS / TST)
Taumelscheibe 13,0° (K2175 TS / TST)
Axial-Rillenkugellager 3-teilig
Innensechskantschraube M 8 x 30
O-Ring 14 x 2
Dichtung für Deckel
Deckel für Ölgehäuse
Schraube M5x12
Ölverschlussschraube mit Messstab
Ölablassstopfen M18x1,5 mit Magnet
Qty.
1
3
1
3
3
3
3
1
1
1
4
2
1
1
4
1
1
Ord.-No
41.020 2
41.031
41.021 1
41.033
41.034
41.032 1
41.035
41.028-12,0
41.028-13,0
43.486
41.036 1
43.445
46.531
46.532
41.019 4
48.017
48.020
41
Transmission
No
Description
1
2
3
4
5
6
7
8
10
12
14
15
16
17
18
20
Gehäuseplatte für 15 mm Plunger
Öldichtung 15 x 24 x 7
O-Ring Viton 88 x 2
Plungerfeder
Federdruckscheibe 15 mm
Plunger 15 mm
Sprengring 15 mm
Taumelscheibe 14,1° (K2195 TS / TST)
Axial-Rillenkugellager 3-teilig
Innensechskantschraube M 8 x 30
O-Ring 14 x 2
Dichtung für Deckel
Deckel für Ölgehäuse
Schraube M5x12
Ölverschlussschraube mit Messstab
Ölablassstopfen M18x1,5 mit Magnet
Qty.
1
3
1
3
3
3
3
1
1
4
2
1
1
4
1
1
Ord.-No
42.906
42.907
41.021 1
41.033
42.909
42.908
42.910
41.028-14,1
43.486
41.036 1
43.445
46.531
46.532
41.019 4
48.017
48.020
42
Spare parts list
Kränzle 2160 / 2195 / 2175
43
Hose drum
No
Description
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Seitenschale Trommelteil
Knickschutz
Kunststoffschraube 5,0 x 20
Antriebswelle
Lagerklotz links
Schraube 6,0 x 30
Lagerklotz rechts
Verbindungsrohr
Wasser-Eingangsteil
O-Ring 6 x 0,8
Handkurbel
Schraube M 5 x 14
Scheibe 5,3
Wellensicherungsring 22 mm
O-Ring 9,3 x 2,4
Dichtsatz
Saugzapfen Schlauchanschluss
Edelstahlkugel 5,5 mm
Edelstahlfeder Eingangsinjektror
O-Ring 10 x 2
O-Ring 6,68 x 1,78
Hochdruckschlauch 15m NW6
Chemikaliensaugschlauch mit Filter
Qty.
Ord.-No
2
1
1
5
1
1
4
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
48.101
48.102
40.162
43.018
48.104 1
43.810
43.423
43.811
48.014
48.103
40.177
48.108
40.536
50.152
40.117
13.273
13.410 1
13.236
13.238
13.239
40.317
43.068
40.585
48.015
15.038
30
Schlauchtrommel kpl., ohne HD-Schlauch
48.100
44 Gun with lance
No
Description
Qty.
Ord.-No
1
2
3
18
Pistolenschale re+li
1
Schraube 3,5 x 14
10
Reparatursatz M2000
O-Ring 9,3 x 2,4
1
12.450
44.525
12.454
13.273
19
20
30
31
32
33
33.1
ST 30-Nippel M 22 x 1,5 AG / M 12 x 1
Rohr 500 lang, bds. M12 x 1
Klemmstück
Halterung für Klemmstück
Kunstoffhülle
Vario-Jet 03 (K 2195)
Vario-Jet 042 (K 2160, K 2175)
13.363
41.527 1
41.155 2
41.155 4
41.155 1
41.155 9
41.155 6
M2000-Pistole kpl. 12.480
Lanze kpl. mit Vario-Jet 03 (K 2195)
Lanze kpl. mit Vario-Jet 042 (K 2160, K 2175)
41.156 8-03
41.156 8-042
1
1
1
1
1
1
1
45
Dirtkiller with lance
No
Description
Qty.
Ord.-No
1
Sprühkörper
1
41.520
2
O-Ring 6,88 x 1,68
1
41.521
3
Düsensitz
1
41.522
4
Düse 03
1
41.523 4
4.1
Düse 042
1
41.523
5
Stabilisator
1
41.524
6
O-Ring
1
40.016 1
7
Sprühstopfen
1
41.526
8
Rohr 500 mm 2x M 12 x 1
1
41.527 1
9
ST 30-Nippel M 22 x 1,5 / M 12 x 1 ISK
1
13.363
11
Kappe vorn für Schmutzkiller
1
41.528 1
12
Kappe hinten für Schmutzkiller 03
1
41.542 1
12.1
Kappe hinten für Schmutzkiller 042
1
41.540 2
Rep.-Satz Schmutzkiller 03
41.096 1
Rep.-Satz Schmutzkiller 042
41.097
bestehend aus je 1x 2; 3; 4; 5
Schmutzkiller 03 kpl. mit Lanze
Schmutzkiller 042 kpl. mit Lanze
41.570-03
41.570-042
46
Wiring diagram Kränzle 2160 / 2195,
230 V, 50 Hz
On-Off switch with 14.5 Ampere
overload protection
Pressure switch
Inlet line via
3 x 1,5 mm2,
230 V / 50 Hz
Pump motor
230 V / 50 Hz
Wiring diagram Kränzle 2175,
400 V, 50 Hz
On-Off switch with 11 Ampere
overload protection
Contactor
Pressure switch
Inlet line via
CEE 4 x 1,5 mm²
400 V / 50 Hz
Pump motor
3 x 400 V / 50 Hz
47
Subject to technical modifications. Order no. 30.790 1
I. Kränzle GmbH
Elpke 97
D - 33605 Bielefeld
Re p r i n t o n l y a l l o w e d w i t h t h e a u t h o r i s a t i o n o f K r ä n z l e .
As date of 26.01.2013
Made
in
Germany
www.kraenzle.com
Download PDF
Similar pages