Installation Instructions
#1500093 - Rev. C
SwingArm™
FLAT SCREEN MONITOR ARM
Contents
Important Safety Instructions............................. 2
Components and Fasteners................................. 3
SA1000 Assembly Instructions............................ 4
LCD Monitor Attachment..................................... 5
Cable Management............................................ 6
Arm Adjustment................................................ 7
Desk Base Template........................................... 8
Important Safety Instructions
Read and understand all these safety
instructions before using the product.
Do not mount the Desk Base of the Arm on an
unstable surface or any surface that could not
mount the Desk Base firmly.
For safety reasons, the internal gas-strut of
the LCD Arm product was pre-adjusted in the
factory to the lowest force to prevent the Arm
body from being recoiled during installation.
During installation, beware of the recoil of
the Arm body when attaching or detaching
the LCD monitor to the Arm. To prevent damage or injury when changing the LCD monitor,
always readjust the gas-strut to the lowest
force level to control the recoil of the Arm
body when the LCD monitor is detached.
Do not attempt to disassemble, service or
modify the product by yourself.
Use only a slightly damp cloth to clean the
Arm surface. Never apply flammable solvents
like alcohol, benzene, thinner, etc. to the
product.
2
Workrite Ergonomics 800.959.9675 www.workriteergo.com
Components
Fasteners
A
a
Desk Base with Clamp
Plastic Spacer
x1
b
x1
B
x1
c Washer
x2
Arm Assembly
d
x1
C
Round Head Cap Screw
Plastic Cap
Disc Spring Washer
x1
e
M5 Hex Wrench
x1
x1
D
Base Cushion
M8 Thread Rod
x1
x1
E
f
g
Wing Nut
U Bracket
x1
h
M4 Hex Wrench
x1
x1
i
M8 Flat Head Cap Screw
x2
j
Round Head Cap Screw
x2
k
M4 6mm Screw
x4
l
M4 10mm Screw
x4
m
Cable Clip
x1
n
M5 10mm Set Screw
x1
o
M3 6mm Screw
x2
p
75mm Vesa Plate
x1
Workrite Ergonomics 800.959.9675 www.workriteergo.com
3
SA1000 Assembly Instructions
Step 7
C
convex side
face up
Step 6
b
c
d
B
Step 5
a
Step 4
A
Step 1
Step 2
D
Step 1
Step 3
i
Step 2
bolt hole >12mm
a
Step 3
Bracket
j
Clamp
c
Step 4
Steps:
DESK CLAMP
g
E
DESK BOLT
Clamp Mount:
1 Mount Bracket to Desk Base then tighten (i)Flat Head Cap Screw with (e)M5 Hex Wrench.
2 Attach (D)Base Cushion to (A)Desk Base.
3 Put Desk Base onto work surface then mount Clamp to the Bracket then tighten (j)Round
Head Cap Screw with (e)M5 Hex Wrench.
4 Put (a) Plastic Spacer over (A) main shaft of Desk Base.
5 Put (B)Arm Assembly onto the main shaft.
6 Insert (b), (c) and (d) into Arm Assembly and tighten with (e)M5 Hex Wrench.
7 Snap (C)Plastic Cap into the top of Arm Assembly.
Grommet Mount:
1 Remove the Bracket from (A)Desk Base with (e)M5 Hex Wrench.
2 Attach (D)Base Cushion to (A)Desk Base.
3 Put Desk Base directly on the bolting hole of work surface and tighten (f)M8 Thread Rod
with (h)M4 Hex Wrench.
Insert (E)U Bracket & (c)Washer through (f)M8 Thread Rod and tighten them with (g)Wing Nut.
4 Follow Desk Mount Steps 4 to 7.
4
Workrite Ergonomics 800.959.9675 www.workriteergo.com
LCD Monitor Attachment
100mm VESA standard
75mm VESA standard
Stand-alone
75mm VESA standard
The combination 75/100mm VESA plate is pre-mounted to the SwingArmTM
Mount the LCD monitor directly to the front plate of the Ball Joint Pivot with the supplied M4 x
6mm (or M4 x 10mm) screws or screws provided by the manufacturer. For 100mm x 100mm
or 75mm x 75mm standard, use the 4 outer corner holes or 4 inner corner holes on the front
plate respectively.
If the mounting area on your monitor is smaller than the 100mm VESA connecting plate
and is recessed, remove the plate and replace it with the smaller 75mm. plate. Then
attach the plate to the back of the monitor.
IMPORTANT
It is strongly recommended to use the mounting screws provided by the LCD monitor
manufacturer. Due to the varieties of monitor mounting design, the mounting holes at
the back of the LCD monitor might not be suitable for the M4 screws provided by our
Product. Using unsuitable mounting screws might cause damage to the LCD monitor.
Please consult your LCD monitor manufacturer if you have enquires.
Workrite Ergonomics 800.959.9675 www.workriteergo.com
5
Cable Management
FOREARM
Thread monitor cable
through Cable Mount
located on underside
of Forearm.
Cable Mount
EXTENSION
Secure Velcro® strips
under side of Extension around
monitor cable(s), leaving slack
for monitor cables to move freely.
Strip
Strip
DESK BASE
Attach the Cable Clip to the
back of the Desk Base with the
supplied M3 Screws and put
cable(s) into the Cable Clip.
M3 Screws
Note:
To allow free movement of monitor and Arm/Extension, please leave sufficient slack in the cable(s).
6
Workrite Ergonomics 800.959.9675 www.workriteergo.com
Arm Adjustment
Adjust the Ball-Joint for Tilt Action
4 Tensioning
Screws
Depending on the weight of the LCD monitor, adjustments may be required to the ball joint
mechanism. If the monitor doesn’t hold its position or is too tight, adjust the four tensioning
screws located around the ball joint cover (clockwise to tighten, counter-clockwise to loosen).
Check the monitor, and then adjust again if necessary.
Vertical Movement
Adjustment Screw
Increase
Tension
Decrease
Tension
Depending on the weight of the monitor, adjustments may be required to the Arm, this can be
done by using the M5 Hex wrench provided.
If the Arm tends to drift down or rise up when positioned, it will be necessary to make small
adjustments at the Adjustment Screw. The above shows the adjusting method. The M5 Hex
wrench provided should be used to make this adjustment.
If the Arm tends to rise, the M5 Hex Wrench should be turned clockwise to decrease the tension
until the Arm reaches a stable position.
If the Arm tends to fall, the M5 Hex Wrench should be turned counter-clockwise to increase the
tension until the Arm reaches a stable position.
IMPORTANT
When performing this adjustment, the Arm must be in a HORIZONTAL position as shown
above. To prevent damage to the aluminium Arm body, remove the M5 Hex Wrench before
releasing the Arm from the horizontal adjustment position.
Workrite Ergonomics 800.959.9675 www.workriteergo.com
7
Desk Base Template
1.57" (40mm)
8
Workrite Ergonomics 800.959.9675 www.workriteergo.com
Download PDF
Similar pages