ROBE Spiider - ROBE lighting

Version 2.0
1
Robin Spiider
Table of contents
1. Safety instructions.......................................................................................................... 3
2. Operating determination................................................................................................. 4
3. Fixture exterior view ...................................................................................................... 5
4. Installation....................................................................................................................... 6
4.1 Connection to the mains............................................................................................. 6
4.2 Eggcrate installation.................................................................................................... 6
4.3 Rigging the fixture....................................................................................................... 7
4.4 DMX-512 connection................................................................................................... 9
4.5 Ethernet connection.................................................................................................. 10
4.6 Wireless DMX operation........................................................................................... 12
5. Remotely controllable functions.................................................................................. 13
6. Control menu map......................................................................................................... 15
7. Control menu ................................................................................................................ 18
7.1 Tab " Address"........................................................................................................... 19
7.2 Tab "Information"....................................................................................................... 20
7.3 Tab "Personality"....................................................................................................... 21
7.4 Tab "Manual Control"................................................................................................. 23
7.5 Tab "Stand-alone" ..................................................................................................... 23
7.6 Tab "Service"............................................................................................................. 24
8. RDM................................................................................................................................ 26
9. Error and information messages................................................................................. 27
10. Technical Specifications............................................................................................. 28
11. Maintenance and cleaning.......................................................................................... 31
11.1 Removing the optical module.................................................................................. 32
11.2 Disposing of the product.......................................................................................... 33
12. ChangeLog .................................................................................................................. 33
13. Photometric diagrams................................................................................................ 34
14. Appendix - DMX modes overview.............................................................................. 36
2
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
1. Safety instructions
Every person involved with installation and maintenance of this device have to:
- be qualified
- follow the instructions of this manual
CAUTION!
Be careful with your operations.
With a high voltage you can suffer
a dangerous electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
Important
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
Handle the power cord and all connections with the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear panel.
WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable
to completely remove power from unit when not in use or before cleaning or servicing the unit.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-cord by the plug. Never pull out the plug by tugging the power cord.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
The electric connection, repairs and servicing must be carried out by a qualified employee.
Do not connect this device to a dimmer pack.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
For replacement use fuses of same type and rating only.
Warning! Risk Group 2 LED product according to EN 62471.
LED light emission. Risk of eye injury. Do not look into the beam at short distance of
the of the product. Do not view the light output with optical instruments or any device
that may conncentrate the beam.
The light source contains blue LEDs.
3
2. Operating determination
This device is a moving head for creating decorative effects and was designed for indoor use only.
This device is for professional use only. It is not for household use.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector head, as the mechanics may be damaged. Always hold the
fixture at the transport handles.
When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture
or dust. There should not be any cables lying around. You endanger your own and the safety of others!
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.
Always secure the fixture with an appropriate safety wire.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
The maximum ambient temperature 45°C must never be exceeded.
To avoid damage of an internal optical system of the fixture, never let the sunlight (or
other light source) lights directly to the lens array, even when the fixture is not working
!
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, burns etc.
Always push the zoom module into the head before inserting the fixture into the flight
case.
4
3. Fixture exterior view
1 - Lens array
2 - Yoke
3 - Handle
4 - QVGA touch screen
5 - Control buttons
6 - USB port
7 - Tilt lock
8 - 3-pin DMX OUT
9 - Ethernet IN
10 - Base
11 - Ethernet OUT
12- 3-pin DMX IN
13- 5-pin DMX IN
14- Mains IN
15- Fuse holder
16- 5-pin DMX OUT
17- Moving head
The head should be locked for transportation - the tilt lock latch (7) has to be in the locked position. To unlock
the head, move this latch to unlock position before operating the fixture.
The ENTER/DISPLAY ON button also serves for switching the display on when the fixture is disconnected
from the mains.
5
4. Installation
Fixtures must be installed by a qualified electrician in accordance with all
national and local electrical and construction codes and regulations.
4.1 Connection to the mains
For protection from electric shock, the fixture must be earthed!
The Robin Spiider is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC
power source from 100-240 Volts.
If you install a cord cap on the power cable to allow connection to power outlets, install a grounding-type (earthed)
plug, following the plug manufacturer’s instructions.
The cores in the power cable are coloured according to the following table.
Core (EU)
Core (US)
Connection
Plug Terminal Marking
Brown
Black
Live L
Light blue
White
Neutral
N
Yellow/Green
Green
Earth
This device falls under class one and must be earthed (grounded)!
To apply power, first check that the head pan and tilt locks are released.
Wiring and connection work must be carried out by qualified staff!
4.2 Eggcrate installation
Disconnect the fixture from mains before eggcrate installation
Screw the eggcrate (1) to the head (3) by means of the three screws (2).
6
4.3 Rigging the fixture
A structure intended for installation of the fixture (s) must safely hold weight of the fixture(s) placed on it. The
structure has to be certificated to the purpose.
The fixture (fixtures) must be installed in accordance with national and local electrical and construction codes
and regulations.
.
For overhead installation, the fixture must be always secured with a safety wire that
can bear at least 10 times the weight of the fixture.
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert before taking into operation for the first time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
Allow the fixture to cool for ten minutes before handling.
The fixture should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working
load limits, installation material being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualifications, do not attempt the installation yourself, but use a help of professional
companies.
CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety
of a possible installation, do not install the fixture!
The fixture has to be installed out of the reach of public.
The fixture must never be fixed swinging freely in the room.
.
Danger of fire !
When installing the device, make sure there is no highly inflammable
material (decoration articles, etc.) in a distance of min. 0.5 m.
CAUTION!
Use 2 appropriate clamps to rig the fixture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is fixed properly! Ensure that the
structure (truss) to which you are attaching the fixtures is secure.
The fixture can be placed directly on the stage floor or rigged in any orientation on a truss without altering its
operation characte­ristics .
For securing the fixture to the truss, install a safety wire which can hold at least 10 times the weight of the fixture.
Use only the safety wire with a snap hook with screw lock gate.
7
Truss installation
1. Bolt the clamp (3) to the omega holder (5) with M12 bolt and lock nut through the hole in the holder.
2. Fasten the omega holders to the bottom of the base by inserting both quick-lock fasteners (2) into
the holes of the base and tighten fully clockwise.
3. Clamp the fixture on a truss (6) and tighten the rigging clamps.
4. Pull the safety wire (4) through the attachment point (1) and through the handle (7) and around the truss (6)
and lock the snap hook with screw lock gate.
Use only a safety wire with a snap hook with screw lock gate.
When installing fixtures side-by-side,
avoid illuminating one fixture with another!
DANGER TO LIFE!
Before taking into operation for the first time,the installation has to be approved by
an expert!
8
In order to protect the internal parts of the head from the sun, the function
PARKING POSITION must be switched ON before switching the fixture off.
The PARKING POSITION function is located on the Power/Special functions channel (120-129 DMX). If the
function is on, the fixture will automatically detect via G-sensor whether the fixture is on the floor or hangs on
the truss or is mounted sideways on the truss and moves the pan and tilt to the position (including movement
of zoom to the front part of the head) in which the head will always face down. Owing this position of the fixture
head, there is not chance to burn internal parts of the head by the sun light.
4.4 DMX-512 connection
The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired
in parallel.
Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in
order to connect the controller with the fixture or one fixture with another.
DMX - outputDMX-input
XLR mounting-sockets (rear view):
XLR mounting-plugs (rear view):
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always connect
one output with the input of the next fixture until all fixtures are connected. Up to 32 fixtures can be connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a 3-pin (5-pin) XLR-plug and plug it in the DMX output of the last fixture.
9
4.5 Ethernet connection
The fixtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control software running on your PC (or light console) has to support Art-Net protocol.
Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow
transfer of large amounts of DMX 512 data over a wide area using standard network technology.
IP address is the Internet protocol address.The IP uniquely identifies any node (fixture) on a network.
The Universe is a single DMX 512 frame of 512 channels.
The Robin Spiider is equipped with 8-pin RJ- 45 socket for Ethernet input.Use a network cable category 5 (with
four “twisted” wire pairs) and standard RJ-45 plugs in order to connect the fixture to the network.
RJ-45 socket (front view):
RJ-45 plug (front view):
1- TD+ 5- Not connected
2- TD-6- RX
3- RX+
7- Not connected
4- Not connected
8- Not connected
Patch cables that connect fixtures to the hubs or LAN sockets are wired 1:1,that is,pins with the same numbers
are connected together:
1-12-23-34-45-56-67-78-8
If only the fixture and the computer are to be interconnected,no hubs or other active components are needed.A
cross-cable has to be used:
1-32-63-14-85-76-27-58-4
If the fixture is connected with active Ethernet socket (e.g. switch) the network icon
will appear at the
bottom right corner of the screen:
Direct Ethernet operation
Connect the Ethernet inputs of all fixtures with the Ethernet network.
Option “Artnet (gMaI or gMA2)" has to be selected from “Ethernet Mode” menu on the fixture.
Set IP address (002.xxx.xxx.xxx / 010.xxx.xxx.xxx) and the Universe.
(DMX address=131)
IP addres=002.168.002.004
Universe=1
(DMX address=30)
IP addres=002.168.002.003
Universe=1
(DMX address=1)
IP addres=002.168.002.002
Universe=1
An advised PC setting: IP address: 002.xxx.xxx.xxx / 010.xxx.xxx.xxx (Different from fixture IP addresses)
NET mask: 255.0.0.0
10
Ethernet / DMX operation
Options “Art2DMX” has to be selected from the “Ethernet Mode” menu on the first fixture (connected to the
Ethernet) in the fixture chain,next fixtures have standard DMX setting.
Connect the Ethernet-input of the first fixture in the data chain with the network. Connect the DMX output of
this fixture with the input of the next fixture until all fixtures are connected to the DMX chain.
Caution: At the last fixture, the DMX chain has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a XLR-plug and connect it in the DMX-output of the last fixture.
Example:
DMX address=1
IP addres=002.168.002.002
Universe=0
DMX address=1
IP addres=002.168.002.003
Universe=1
DMX address=49
DMX address=49
11
DMX address=131
DMX address=131
4.6 Wireless DMX operation
The wireless version of the Robin Spiider is equipped with the Lumen Radio CRMX module and antenna for
receiving DMX signal. CRMX module operates on the 2.4 GHz band.
The item " Wireless " from the menu "DMX Input" allows you to activate receiving of wireless DMX (Personality--> DMX Input -->Wireless.). First two options from the "DMX Input" menu are stated in DMX chart as well
(channel Power/Special functions , range of 10-19 DMX). If DMX input option is changed by DMX command,
the change is permanently written into fixture´s memory.
DMX range of 10-19 switching fixture to the wired/wireless operation is active only during first 10 seconds after switching the fixture on.
After switching the fixture on, the fixture checks both modes of receiving DMX in the following order:
1. For the first five seconds, the fixture receives DMX signal from the wired input. If the Power/Special functions
channel is set at some DMX input option, the fixture will receive DMX value according to this option. If DMX input
option is set to the wired input , this option is saved and checking procedure is finished. If DMX input option is
not set, the fixture continues next 5 seconds in scanning wireless DMX signal-see point 2.
2. For the next 5 seconds the fixture receives wireless DMX signal and again detects if the Power/Special
functions channel is set at some DMX input option, if not, the fixture will take option which is set in the fixture
menu "DMX Input".
To link the fixture with DMX transmitter.
The fixture can be only linked with the transmitter by running the link procedure at DMX transmitter .
After linking , the level of DMX signal ( 0-100 %) is displayed in the menu item “Wireless State“ (Information
-->Wireless State).
To unlink the fixture from DMX transmitter.
The fixture can be unlinked from receiver via the menu item “ Unlink Wireless Adapter“ (Information--> Wireless
State --> Unlink Wireless Adapter.).
Note: If the option "Wireless In/XLR Out" is selected (Personality--> DMX Input -->Wireless In/XLR Out), the
fixture receives wireless DMX and sends the signal to its wired DMX output. The fixture behaves as " Wireless/
Wired" adapter.
Example:
12
5. Remotely controllable functions
Virtual colour wheel
This wheel contains 66 preset colours, rainbow effect in both directions is available.
Colour temperarature correction (CTC)
This channel allows to set calibrated white colour from range of 8000K-2700K.
RGBW or CMY colour mixing system
The RGBW colour mixing system is based on red, green, blue and white high power LEDs. Option for switching
the fixture to the CMY colour mixing system is available.
Colour Mix control
The Colour Mix control channel defines relation between global colours (RGBW, CTO, Virtual colour wheel)
and individual RGB pixels or Kling-Net.
Global = Global Colours (RGBW, CTO, Virtual Color Wheel)
Pixel = Pixel Colors (RGB individual pixels or Kling-Net)
DMX value
Function
0-9
Global colours (Global has priority)
10-19
Maximum mode (highest values have priority)
20-29
Minimum mode (lowest values have priority)
30-39
Multiply mode (multiply Global and Pixel)
40-49
Addition mode (Global + Pixel) - default
50-59
Subtraction mode (Global – Pixel)
60-69
Inverted Subtraction mode (Pixel – Global)
70-79
Coloured background
80-127Reserved
128
Global colours (Global has priority)
129-254
Crossfade (crossfade between Global and Pixel)
255
Pixel colours (Pixel has priority)
E.g. If you wish to control RGBW channels, set the Colour Mix Control channel to 0 DMX, if you
need to use pixel effects, set the Colour Mix Control channel to 255 DMX.
Flower Effect
The flower effect rotating in both directions allows to create many dynamic effects.
Zoom
Motorized zoom offers beam range of 4° to 50°.
Pixel control and pixel effects
19 RGB pixels allow you to create many effects or use 90 pre-defined pixel effects
Pixel order:
Dimmer/Shutter unit
Smooth 0 - 100 % dimming is provided by the electronic control unit. This unit is also used for strobe effects
with variable speed.
13
Pan/Tilt
Precise pan/tilt movement due to built-in electronic motion stabilizer. The electronic motion stabilizer ensures
precise position of the fixture´s head during its movement and reduces its swinging when the truss shakes.
Pan movement range: 540°,tilt movement range: 220°.
14
6. Control menu map
Default settings=Bold print
Tab
Level 1
Level 2
Level 3
Addressing
Settings
DMX Address
001-255
DMX Preset
Mode 1, Mode 2,
Mode 3, Mode 4
Ethernet Settings
Ethernet Mode
-
Level 4
Level 5
Disable
ArtNet
gMAI
gMA2
sACN
Ethernet To DMX
Off, On
IP Address/Net Mask
Default IP Address
Custom IP Address
Net Mask
ArtNet Universe
0-255
MANet settings
MANetI/II Universe
01-256
MANet Session ID
01-32
sACN Universe
00001-32000
sACN Priority
0-255
sACN Settings
Klingnet Settings
Disable
Enable
Information
Fixture Times
Power On Time
Total Hours
Resetable Hours
Air Filters
Elapsed Time
Alert Period
Fixture Temperatures
LEDs Temperature
Current
Maximum NonRes.
Maximum Res.
Base Temperature
Current
Maximum NonRes.
Maximum Res.
DMX Values
Pan
:
Blue Pixel 19
Wireless State
Signal Quality
Unlink Wireless
Adapter
Power Channel State
Software Versions
Display System
Module M
Module DR
Module PX
Product IDs
Mac Address
RDM UID
RDM Label
View Logs
Fixture Errors
Fixture States
Power On
Power Off
Fixture Position
Fixture Temperatures
LEDs Temperatures
Base Temperatures
15
10-300
Level 6
Tab
Level 1
Level 2
DMX Presets
Mode 1
Level 3
Level 4
Personality
:
Mode 6
:
Mode 10
View Selected Preset
DMX Input
Wired Input
Wireless Input
Wireless In/XLR Out
Pan/Tilt Settings
Pan Reverse
Off, On
Tilt Reverse
Off, On
Pan/Tilt Feedback
Off, On
Pan/Tilt mode
Time
Speed
Pan/Tilt EMS
On, Off
Pixel Control
Pixel Index
0-11
Pixel Mirror
On, Off
Reset to default
Microphone Sensitivity
1-10-20
Blackout Settings
Blackout During M.C.
Off, On
Blackout while:
Pan/Tilt moving
Colour Mixing Mode
RGBW
CMY
White Point 8000K
Off, On
Tungsten Eff. Sim.
Off
750W
1000W
1200W
2000W
2500W
Dimmer Curve
Linear
Square Law
Init Effect Positions
Pan
0-255
:
Screen Settings
Dimmer Fine
0-255
Display Intensity
1-10
Screen Saver Delay
Off-10min.
Touchscreen Lock
Off-10min.
Recalibrate Touchscreen
Display Orientation
Normal
Inverted
Auto
Temperature Unit
°C,°F
Fan Mode
Auto
High
Date & Time Settings
Default Settings
Manual Control
Reset Functions
Total System reset
Pan/Tilt reset
Zoom Reset
Flower E. Reset
Manual Effect Control
Pan
0-255
:
Blue Pixel 19
0-255
16
Off, On
Level 5
Level 6
Tab
Level 1
Level 2
Stand -Alone
Test Sequences
Dynamic Mode
Static Mode
MusicTrigger
Off, On
Preset Playback
None
Level 3
Level 4
Level 5
Level 6
Pan
0-255
Tilt
0-255
Zoom
0-255
Start Step
1-100
End Step
1-100
Edit Program Steps
Step 1
Pan
0-255
:
:
:
Dimmer Fine
0-255
:
Step Time
0-25,5 sec.
Step 100
Pan
0-255
Test
Prog. 1
Prog. 2
Prog. 3
Play Program
Play Program 1
Play Program 2
Play Program 3
Edit Program
Edit Program 1
:
Service
Adjust DMX Values
Pan
0-255
:
Calibrations
Blue Pixel 19
0-255
Calibrate Effects
Pan
0-255
Tilt:
0-255
Red
0-255
Green
0-255
Blue
0-255
White
0-255
Calibrate colours
Calibrate Pan/Tilt EMS
Load Default Calibrations
Update Software
17
Dimmer Fine
0-255
Step Time
0-25,5 sec.
7. Control menu
The Robin Spiider Light is equipped with the QVGA Robe touch screen with battery backup which
allows to set the fixture´s behaviour according to your needs, obtain information on its operation, test its
various parts and lastly program it, if it has to be used in a stand-alone mode.
The fixture´s menu can be controlled either by the control buttons or directly by touching the icon.
Control buttons on the front panel:
[ESCAPE] button used to leave the menu without saving changes.
[NEXT] , [PREV] buttons for moving between menu items and symbols, adjusting values.
[ENTER/Display On] button used to enter the selected menu (menu item) and to confirm adjusted value.
If the fixture is disconnected from mains, the button switches the touch screen on.
Icons used in the touch screen menu:
- [back arrow] used to move back to the previous screen (menu).
- [up arrow] used to move up on the previous page.
- [down arrow] used to move down on the next page.
- [confirm] used to save adjusted values, to leave menu or to perform desired action.
- [cancel] used to leave menu item without saving changes.
- [confirm+copy] used to save adjusted values and copy them to the next prog. step.
- [warning icon] used to indicate some error which has occurred in the fixture.
- [Ethernet] used to indicate Ethernet connected.
- [display turn] used to turn the display by 180°.
- [slider control] used to recall slider system for setting desired value.
- [keyboard control] used to recall keyboard system for setting desired value.
- [air filters cleaning] used to signal that cleaning period of the air filters elapsed.
The menu page displays icons for each function that you can perform from the touch screen.
After switching the fixture on, the touch screen shows the screen with the ROBE logo:
18
Note: The green icon at the top right corner of the screen indicates the level of the display battery charging. If
the whole icon is green, the battery is fully charged while the red icon indicates exhausted battery. The battery
charges during fixture operation, its charging lasts cca 6 hours.
We recommend that the fixture should be in operation at least 7 hours per week to keep the battery fully charged.
If you switch the fixture on and this screen will not appear till 1 minute, switch the fixture off and on again. If the
screen lights, the battery is exhausted. In case the screen still does not light, the battery is faulty.
This is also indicated by an error message "Faulty battery" and if such an error message appears the battery
should be replaced immediately. The lifetime of the battery is highly dependent on ambient temperature (and
consequently on base temperature). If the maximum ambient temperatures (as recorded and displayed in menu:
Information -> Fixture Temperatures -> Ambient Temperature -> Maximum NonRes.) are kept within the specified limits, the battery should last for at least two years. Shell the ambient temperatures exceed the specified
maximum temperature, the lifetime of the batteries could be considerably shortened even up to just one year
or less and also result in physical damage (battery leakage) or unreliable fixture functions.
Damage caused by batteries failed due to exceeded maximum ambient temperature cannot be claimed under
warranty terms.
Touch any part of the screen or press the [ENTER/Display On] button to display the initial screen with the current stored DMX address:
Touch the green arrow at the bottom right corner of the screen or press the [ENTER/Display On] button to enter
the " Address" menu.
Each item (such as a Tab, menu item, text box, icon) may be selected from a screen by simply touching the
item in the list or by pressing the [NEXT] or [PREV] buttons to scroll through list items. With each press, the
next item is highlighted. Press [ENTER/Display On] to select the highlighted item.
Before first fixture operation, set current date and time in the menu "Date &Time
Setings" (menu path: Personality--> Date &Time Setings).
7.1 Tab " Address"
DMX Address - Select the menu to set the DMX start address.
DMX Preset - Use the menu to select desired channel mode.
View Selected Preset - Use the menu to display channels included in the selected mode.
Ethernet Settings - The menu allows all needed settings for the Ethernet operation
Ethernet Mode
Disable - The option disables Ethernet operation.
Artnet - Fixture receives Artnet protocol
gMAI - Fixture receives MANet I protocol
gMA2 - Fixture receives MANet 2 protocol
sACN - Fixture receives sACN protocol
Ethernet To DMX - Fixture receives protocol from the Ethernet input and sends DMX
data to its DMX output (fixture works as an "Ethernet/DMX converter", next fixture can be connected
to its DMX output and you can build a standard DMX chain by connecting another fixtures.
Only one fixture has to be connected to the Ethernet.
19
IP Address/Net Mask - Select this menu to set IP address. IP address is the Internet protocol
address.The IP uniquely identifies any node (fixture) on a network.
There cannot be 2 fixtures with the same IP address on the network!
Default IP Address -Preset IP address, you can set up only first byte of IP address
(2 or 10) e.g. 002.019.052.086.
Custom IP Address - The option enables to set up all bytes of IP address.
Net Mask - The option enables to set up all bytes of Net Mask.
ArtNet Universe - Use this item to set a Universe (0-255). The Universe is a single DMX
512 frame of 512 channels.
MANet Settings - Use this menu to set parameters for MANet operation.
MANet Universe I/II - The value of this item can be set in range 1-256.
MANet Session ID - The value of this item can be set in range 1-32.
sACN Settings - Use this menu to set parameters for sACN operation.
sACN Universe - The value of this item can be set in range 1-32000.
sACN Priority - The value of this item can be set in range 0-255.
Klingnet Settings - Use this menu to enable or disable Klingnet protocol.
7.2 Tab "Information"
Fixture Times - The menu provides readouts of fixture operation hours and air filters using hours.
Power On Time Hours - Select this menu to read the number of fixture operation hours.
Total Hours - The item shows the total number of the operation hours since the Robin Spiider has been fabricated.
Resetable Hours - The item shows the number of the operation hours that the Robin Spiider has been powered on since the counter was last reset.
In order to reset this counter to 0, touch the text box next to the item "Resetable Hours:"
Air Filters - Regular cleaning of the air filters is very important for the fixture´s life and performance.
Bild-up of dust, dirt and fog fluid residues reduces the fixture´s light output and cooling ability.
The two items of this menu help you to keep cleaning period of the air filters.
Alert period - Cleaning schedule for the fixture depends on the operating environment.
It is therefore impossible to specify accurate cleaning interval. This item allows
you to change the cleaning interval of the air filters. This "alert" value is 300 hours and it
is set as default. Inspect the fixture within its 300 hours of operation to see whether cleaning
is necessary. If cleaning is required, clean all air filters and change the value in this menu
on acceptable level. Min. level of alert period is 10 hours, max. is 300 hours.
Elapsed Time - The item allows you to read the time which remains to cleaning air filters.
The time period is set in the menu mentioned above.
Expired time period is signalled by a negative mark (-) at the time value and a warning icon
on the display.
Clean the filters and reset this menu item (by touching the text box next to the item
"Elapsed Time").
Fixture Temperatures - The menu is used to view temperatures of the fixture´s inside.
LEDs temperatures - The menu shows temperature on the LEDs PCB .
Cur. - A current temperature of the LEDs PCB.
Max. - A maximum temperature of the LEDs PCB since the fixture has
been fabricated.
Max. Res. - A maximum temperature of the LEDs PCB since the counter
was last reset.
In order to reset some counter to 0, touch desired text box under item "Max.Res."
Base Temperature - The menu shows temperature in the fixture base (on the display PCB).
Current - A current temperature in the fixture base.
Maximum NonRes. - A maximum temperature in the fixture base since the fixture has
been fabricated.
20
Maximum Res. - A maximum temperature in the fixture base since the counter
was last reset.
In order to reset this counter to 0, touch the text box next to the item "Maximum Res."
DMX Values - The menu is used to read DMX values of each channel received by the fixture.
Wireless State - The menu serves for reading of the wireless operation status.
Unlink Wireless Adapter - The item serves for unlinking the fixture from DMX transmitter.
Power Channel State - The menu item shows state of the Power/Special functions switches.
Software Version - Select this item to read the software version of the fixture modules:
Display System - A display processor on the display board in the fixture base
Module M - A pan/Tilt processors
Module DR - A LEDs driver
Module PX - Pixels + zooms control
Product IDs - The menu is used to read the MAC Address ,RDM UID and RDM Label.
View Logs - Use this menu to read fixture´s data which have been recorded during fixture operation. This
colected data allows easier troubleshooting.
Fixture Errors - Use this menu to read fixture errors which have occured during fixture operation.
Fixture States - Recorded following actions: Fixture On, Fixture Off.
Fixture Position - Recorded installation positions of the fixture:
Fixture Temperatures - Recorded temperatures which have exceeded defined levels.
Note: The log buffer can contain 8000 records max. If the buffer is full, old data will be overwritten.
7.3 Tab "Personality"
DMX Preset - Use the menu to select desired channel mode.
View Selected Preset - Use the menu to display channels included in the selected mode.
DMX Input- Use the menu to select mode of receiving DMX signal.
Wired - DMX signal is received by means of the standard DMX cable.
Wireless - DMX signal is received by means of the inbuilt wireless module.
Wireless In/XLR Out- the fixture receives wireless DMX and sends the signal to its wired DMX output.
The fixture behaves as " Wireless/Wired" adapter.
The options "Wired" and "Wireless" are also stated in DMX chart (channel Power/Special functions).
Pan/Tilt Settings - Use the menu set behaviour of both pan and tilt movements.
Pan Reverse - The item allows to invert pan movement.
Tilt Reverse - The item allows to invert tilt movement.
Pan/Tilt Feedback - The item allows to return the mowing head to the required pan/tilt position after
changing the position by an external force if this option is set on.
Note. Be careful, the Pan/Tilt Feedback should be permanent On, the option Off is not suitable for standard
operation and the head of the fixture can be damaged!
Pan/Tilt mode - Use this menu to set the mode of the pan/tilt movement
Time mode – The pan and tilt will move with different speeds and they will come at
21
the same time to the end point of their tracks (pan and tilt use their optimal speeds).
Time of the pan/tilt movement (25.5 sec. max.) is set by the channel "Pan/Tilt speed, Pan/Tilt
time".
Speed Mode - Both Pan and tilt will move with the same speed as adjusted at the channel
"Pan/Tilt speed, Pan/Tilt time".
Pan/Tilt EMS - Built-in electronic motion stabilizer ensures precise position of the fixture´s head during its
movement and also reducing its swinging when the truss shakes.
Pixel Control - Use the menu to index or mirror pixels.
Pixel Index - The item allows you to choose 12 positions of turned pixels.
Pixel Mirror - The item allows mirroring of pixels along a vertical axis.
Both functions you can also find on the channel Power/Special functions (210-225 DMX).
Important: If you use DMX commands to set values for both Pixel Index and Pixel Mirror functions, set values will
be lost after switching the fixture off. In order to save the values to the fixture, go to DMX value of 237 and stay
in it for 3 sec. The set values will be saved to the fixture and will not be lost by switching the fixture off and on.
Reset to default - The item sets items "Pixel Index" and "Pixel Mirror" to default (factory) values.
Microphone Sensitivity - Enter the menu if you want to adjust the microphone sensitivity from 1 (max.) to 20
(min.).
Blackout Settings - Use the menu if you need to close the light output under certain conditions which are
described below
Blackout DMC - Blackout during movement correction. Set this option On if you wish to close light
output during the time when the head goes to its correct position, which has been changed by an
external force.
Active Blackouts - Use this menu if you wish to close the light output during effect changes.
Pan/Tilt Moving - The menu item enables to close light output while the pan/tilt coordinates
are changing.
White Point 8000K - If the function is on, the CTC channel allows to set desired white in range of 8000K-2700K
(0 DMX=8000K, 255 DMX=2700K). Necessary condition is , that RGBW channels have to be full or set at the
same DMX values, e.g. 150.
If this function is off, the range of whites is not uniform and may be different for each fixture.
Colour Mixing Mode - This item allows switching into RGBW or CMY mode. In the CMY mode, the white(8bit)/
white (16) bit channels are not active.
Tungsten Effect Sim. - This function simulates behaviour of a halogen lamp during dimming at calibrated whites
2700K, 3200K. You can select from various lamp wattage simulation: 750W, 1000W, 1200W, 2000W, 2500W.
Dimmer Curve - You can select desired dimmer curve: Linear or Square Law.
Init Effect Positions - Use the menu to set all effects to the desired positions at which they will stay after
switching the fixture on without DMX signal connected.
Screen Settings - Use this menu to change the touch screen settings.
Display Intensity - The item allows to control the intensity of the screen (1-min., 10-max.).
Screen saver Delay - The item allows you to keep the screen on or to turn it off automatically after 1-10
minutes after last touch (or pressing any button on the control panel).
Touchscreen Lock - The item allows you to lock the screen after last touch (or pressing any button on the
control panel). The time delay can be set in range of 1-10 minutes.To unlock the screen, press the
[ENTER/Display On] button.
Recalibrate Touchscreen - The item starts calibration of the touchscreen. Follow the instructions on
the screen.
22
Display Orientation - The menu allows to change display orientation.
Normal - Standard display orientation if the fixture is placed horizontally (e.g. on the ground).
Inverted - This function rotates menu 180 degrees from current orientation.
Auto - The option activates a gravitation sensor for automatic screen orientation.
Note: Auto option is set as default. You change the display orientation by touching the icon
on the display,
an the option set in the "Display Orientation" menu is temporarily overriden.
Temperature unit - Use the menu item to change temperature unit from °C to °F.
Fan Mode - Use the menu to set the fixture fans to max. power mode ("High") or to auto-control mode ("Auto").
Date & Time Settings - Use this menu to set current date and time for the fixture log system (menu "View
Logs"). Set this menu item before first fixture operation.
Default Settings - The menu item allows to set all fixture parameters to the default (factory) values.
7.4 Tab "Manual Control"
Reset Functions - The menu allows to reset the fixture either per function modules or all modules together.
Total System Reset - The item resets all function modules.
Pan/Tilt Reset - The item resets a pan and tilt movement.
Zoom Reset - The item resets zoom.
Flower E. Reset - The item resets Flower effect.
Manual Effect control - Use the menu to control all fixture channels by means of the control panel.
7.5 Tab "Stand-alone"
Test Sequences -Use the menu to run a test/demo sequences without an external controller, which will show
you some possibilities of using Robin Spiider.
Dynamic Mode - This mode uses all Robin Spiider functions including pan/tilt movement and therefore
is good for a complete introduction of the fixture.
Static Mode - This mode is suitable for projections on the wall, ceiling or ground without any pan/tilt movement.
Adjust the pan and tilt to desired positions and start test sequences by touching the green icon.
Music Trigger - Use the item to activate the sound control of the running program via the built-in microphone.
Preset Playback - This menu allows you to select the program which will be played in a loop after switching
the fixture on (the option is commonly used in a stand-alone operation without an external controller).
None - The option disables “Presetting playback” function.
Test - The option starts the test sequences.
Prog. 1 - The option starts user program No. 1.
Prog. 2 - The option starts user program No. 2.
Prog. 3 - The option starts user program No. 3.
Play program - Use the menu to run desired program in a loop.
Play Program 1 - The option starts user program No.1.
Play Program 2 - The option starts user program No. 2.
Play Program 3 - The option starts user program No. 3.
Edit Program - Use the menu to create or to edit desired program. The Robin Spiider offers 3 free programs,
each up to 100 steps.
Edit Program 1 - The option allows to edit user program No.1.
Edit Program 2 - The option allows to edit user program No.2.
Edit Program 3 - The option allows to edit user program No.3
23
To edit program:
1. Touch the item which you want to edit (“Edit Program 1” - “Edit Program 3”).
2. Touch the item "Edit Program Steps".
3. Touch the item "Step 1".
4 From the list of effects touch desired effect and set its value. Browse throw the list by touching the [up arrow]
and [down arrow] and set all desired effects.
An item "Step Time" (value of 0-25.5 sec.) is the time during which effects last in the current step
5. Save adjusted effects to the current step by touching the [confirm] or save and copy them to the following
step by touching the [confirm+copy]. By touching the text box "Preview" next to the current program step you
can view created scene.
6. Repeat the steps 4 and 5 for next program steps.
7. After editing desired program steps, adjust the length of the program by touching the text boxes "Start Step"
and "End Step".
Meaning of the icons used in the "Edit Program" menu:
- moves down on the next page
- saves adjusted values and leaves menu
- moves up on the previous page
- saves values to the current step and copy them to the
following prog. step
- leaves menu without saving values
7.6 Tab "Service"
Adjust DMX Values - The menu allows you to set all effects to desired positions before fine calibration of the
effects .
Calibrations - This menu enables fine calibration of fixture effects and download default calibration values.
Calibrate Effects - The menu allows the fine adjustment of effects.
Pan- a pan position fine adjustment
Tilt - a tilt position fine adjustment
Calibration of the effects via the control board
1. Disconnect DMX controller from the fixture and enter the "Calibrate Effects" menu.
2. Use the [up arrow] and [down arrow] to find "Pan" and touch it to enter the fine effect adjustment screen.
3. Set desired value and save it by touching the [confirm].
4. Repeat steps 2 and 3 for next item
5. After calibrating all effects, touch the [confirm] to save all adjusted values and reset the fixture.
Calibrate Colours - The menu serves for adjusting of LEDs saturation to achieve uniform white colours
Red - a red LEDs saturation fine adjustment
Green - a green LEDs saturation fine adjusment
Blue - a blue LEDs saturation fine adjustment
White - a white LEDs saturation fine adjustmentt
Calibration of white colours via the control board
1. Disconnect DMX controller from the fixture , open shutter and dimmer and set the CTC channel
to DMX=64 (white 5600K), RGBW channels to 255 DMX and Zoom channel to 128 DMX.
2. Set the following items in the menu Personality:
White Point 8000K =On
Colour Mixing Mode=RGBW
3. Aim the light beam on the lux meter (e.g. Minolta CL-500 Chroma meter) which is placed at
min. distance of 3 m from the fixture.
4. Enter the menu Calibrate Colours.
5. By means of the Red, green, Blue and White items adjust the 5600K colour temperature as exactly as
possible (∆u´v´= 0).
6. After adjusting 5600K colour temperature, touch the [confirm] to save all adjusted values and reset
the fixture.
24
Calibration protocol:
Effect
Pan-fine adjustment
Tilt - fine adjustment
Red - red saturation
Green- green saturation
Blue - blue saturation
White - white saturation
Mode 1
channel 49
channel 50
channel 51
channel 52
channel 53
channel 54
Mode 2
channel 29
channel 30
channel 31
channel 32
channel 33 channel 34
Mode 3
channel 33
channel 34
channel 35
channel 36
channel 37
channel 38
Mode 4
channel 91
channel 92
channel 93
channel 94
channel 95
channel 96
Calibrate Pan/Tilt EMS - This menu item allows calibration of the pan/tilt electronic motion stabilizer.
Important: during this calibration any external force must not influence the fixture and the surface at which
the fixture stands (or truss if the fixture hangs) has to be without movement, shake, strokes etc.
Load Default Calibrations - The item loads default (factory) calibration values.
Update software - The menu item allows you to update software in the fixture via either serial or USB port of PC.
The following are required in order to update software:
- PC running Windows 10/8/7 or Linux
- DMX Software Uploader
- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
Note: Software update should execute a qualified person. If you lack qualification, do not attempt the
update yourself and ask for help your ROBE distributor.
DMX address, IP address, programs 1-3 and all items in the menu "Personality" will be set to their default
(factory) values.
To update software in the fixture:
I. Installation of the DMX Software Uploader.
1. DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.
2. Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3. Unpack the software.
II.Fixture software updating.
1.Determine which of your ports is available on your PC and connect it:
- with the DMX input of the fixture if you using the flash cable RS232/DMX
- with the DMX output of the Robe Universal Interface if you using the USB cable.
Disconnect the fixture from the other fixtures in a DMX chain. Turn both the computer and
the fixture on. Make sure the lamp is switched off (only if the fixture involves a lamp).
2. Switch the fixture to the updating mode by touching the "Updating Software " item
Note: If you do not want to continue in software update, you have to switch off and on the fixture
to escape from this menu.
We recommend to cancel all running programs before starting the Software Uploader.
3. Run the Software Uploader program. Select desired COM and then click on the Connect button.
(Select COM if the serial port is used or Robe Universal Interface if the USB port is used).
If the connection is OK, click on the “Start Uploading button“ to start uploading. It will take several
minutes to perform software update.
If the option "Incremental Update" is not checked, all processors will be updated (including
processors with the same software version).
If you wish to update only later versions of processors, check the “Incremental Update box“.
Avoid interrupting the process. Update status is being displayed in the Info Box window.
When the update is finished, the line with the text “The fixture is successfully updated“ will appear in
this window and the fixture will reset with the new software.
Note: In the case of an interruption of the upload process (e.g. power cut), the fixture keeps the updating mode
and you have to repeat the software update again.
25
8. RDM
This fixture supports RDM operation. RDM (Remote Device Management) is a bi-directional communications
protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and
status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting
existing non-RDM equipment. By using a special „Start Code,“ and by complying with the timing specifications
for DMX512, the RDM protocol allows a console or dedicated RDM controller to send commands to and receive
messages from specific moving lights.
RDM allows explicit commands to be sent to a device and responses to be received from it.
The list of commands for Robin Spiider is the following.
Parameter ID
Discovery command SET command
DISC_UNIQUE_BRANCH
*
DISC_MUTE
*
DISC_UN_MUTE
*
DEVICE_INFO
*
SUPPORTED_PARAMETERS
*
SOFTWARE_VERSION_LABEL
*
DMX_START_ADDRESS
*
*
IDENTIFY_DEVICE
*
*
DEVICE_MODEL_DESCRIPTION
*
MANUFACTURER_LABEL
*
*
DEVICE_LABEL
2
GET command
*
SENSOR_DEFINITION
*
SENSOR_VALUE
*
DISPLAY_INVERT
*
*
DISPLAY_LEVEL
*
*
PAN_INVERT
*
*
TILT_INVERT
*
*
DEVICE_RESET
*
DMX_PERSONALITY
*
*
DMX_PERSONALITY_DESCRIPTION
*
STATUS_MESSAGES
*
STATUS_ID_DESCRIPTION
*
DEVICE_HOURS
*
2
ROBE_DMX_INPUT
*
ROBE_WIRELESS_UNLINK
...Commands relative resetable values
*
RDM model ID for the Robin Spiider is 0x00c5.
26
*
9. Error and information messages
Information icon
- Air Filters Cleaning
This icon signalizes that cleaning period of the air filters has elapsed
and you have to clear air filters and reset the menu item "Elapsed Time".
Errors
Error in the fixture is signalled by the yellow warning icon at the bottom line of the screen:
Touch the warning icon or press the [ESCAPE] button to display error messages.
List of error and information messages:
Temper.Sensor Error
The message informs you that the communication betwen the head temperature sensor and the main processor
failed.
Tilt Error 1 (Tilt Error 2)
This message will appear after the reset of the fixture if the head´s magnetic-indexing circuit malfunctions
(sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The head
is not located in the default position after the reset.
Pan Error 1 (Pan Error 2)
This message will appear after the reset of the fixture if the yoke´s magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The yoke is not
located in the default position after the reset of the fixture.
Zoom Error 1 (Zoom Error 2 )
The messages will appear after the reset of the zoom module if the zoom module is not located in the default
position.
Rod Error
The messages will appear after the reset of the flower effect if the rod is not in the default position.
EEprom Error
Hardware error of the EEprom.
Recharge The battery
The battery on the display board needs to be charged. Let the fixture on for cca 6 hrs.
Battery faulty. Replace it.
The battery on the display board is exhausted and should be replaced immediately.
Pan/Tilt EMS Cal. Error
The EMS system is not calibrated.
Pan/Tilt EMS Error
Control electronics cannot communicate with the EMS system.
Clean Air Filters
The message informs that the item "Elapsed Time" in the "Fixture Information" menu is at 0 value. Clean air
filters and reset this counter.
27
10. Technical Specifications
Electrical
Power supply:.........................electronic auto-ranging
Input voltage range:............... supply 100-240V, 50-60Hz
Fuse:.......................................T 8 A
Max. power consumption .......600W at 230V ( power factor= 0.98; I=2.7A)
Optic
Light source: 19 RGBW LED multichips
RGBW or CMY colour mixing
19 controllable LED multichips (pixels)
Min. LED life expectancy: 20.000 hours (at full load of LEDs)
Virtual colour wheel
66 preset colours
CTC in range of 2700K-8000K
Halogen lamp effect at whites 2700K and 3200K
Rainbow effect with in both directions with variable speed
Zoom
Effect
Strobe
Dimmer
Linear motorized zoom
Min. beam angle: 4° (1/2 beam)
Max. beam angle: 50°(1/10 beam)
Flower effect rotating in both directions
10 Flower effect macros
Strobe effect with variable speed (0.3 - 20Hz)
Smooth dimmer from 0 - 100 %
Control
Graphic touch screen for fixture setting and addressing
Gravitation sensor for auto screen positioning
Battery backup of the touch screen
Readout fixture and LED module usage, receiving DMX values, temperatures, etc
Built-in analyzer for easy fault finding, error messages
Built-in demo sequences
Individual pixel control of each LED
Stand-alone operation
3 user editable programs, each up to 100 steps
Supported protocols: USITT DMX 512, RDM, ArtNet, MANet, MANet2, sACN, Kling-Net
Support of RDM (Remote Device Management)
10 DMX modes (49, 27, 33, 90, 27,47, 91,110,104,123 control channels)
Wireless DMX/RDM module (only for Wireles DMX version)
Compliance with USITT DMX-512 (1986 & 1990) and 512-A
Full DMX fidelity and frame integrity
Auto sensing of DMX frame rate and frame size
<5ms DMX latency
Operational frequency range of 2402-2480 MHz
Producer: LumenRadio
28
Pan/Tilt
Connection
Pan movement range 540°
Tilt movement range 220°
Continual pan/tilt rotation
16 bit movement resolution
Pan/Tilt electronic motion stabilizer
Automatic Pan/Tilt position correction
Remotely controllable speed of pan/tilt movement for easy programming
Movement control: tracking and vector
Pan/tilt-lock mechanism
DMX data in/out: Locking 3-pin and 5-pin XLR
AC power IN: Neutrik TrueOne NAC3MPX
Ethernet IN/Out: RJ45
Max. number of fixtures in Ethernet IN/Out line
5
Rigging
Temperatures
Mounting points: 2 pairs of 1/4-turn locks
Mounting horizontally or vertically via two Omega brackets
Maximum ambient temperature : 45° C
Maximum housing temperature : 75° C
Minimum distances
Min. distance from flammable surfaces: 0.5 m
Min. distance to lighted object: 1 m
Total heat dissipation
Maximum: 2040 BTU/hr
Ingress protection
Accessories
IP2x
1 x Omega adapter CL-regular 2 pcs in box (P/N 10980033)
1 x power cable
Weight (net)
13.25 kg
29
Dimensions (mm)
Optional accessories
Upgrade kit CRMX Universal 260 (P/N 99030100)
EggCrate for Robin Spiider (P/N10980317)
Diffuser 2° for Robin Spiider (P/N 10980416)
Doughty Trigger Clamp (P/N 17030386)
Safety wire 35 kg (P/N 99011963)
30
11. Maintenance and cleaning
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build
up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will
not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
DANGER !
Disconnect from the mains before starting any
maintenance and cleaning work
The outer side of the front optical module should be cleaned monthly by means of a vacuum cleaner as dust
reducing the light-output very quickly. The cooling fans should be cleaned at least twice a year.
The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air-jet.
Important! Check the air filter periodically and clean before they become clogged!
Periodically clean air filter placed in the fixture´s base. The air filter cover is fastened by means of magnets.
Use a vacuum cleaner, compressed air or you can wash them and put back dry.
After replacing the air filters, reset the elapsed time counter in the menu "Information" (Information--->Air Filters---> Elapsed Time).
Replacing the fuse.
Before replacing the fuse, unplug mains lead.
1) Remove the fuse holder on the rear panel of the base with a fitting screwdriver from the housing
(anti-clockwise).
2) Remove the old fuse from the fuse holder.
3) Install the new fuse in the fuse holder (only the same type and rating).
4) Replace the fuseholder in the housing and fix it.
31
11.1 Removing the optical module
The following instructions are intended for service purposes only.
To remove the optical module
1. Disconnect the fixture from mains.
2. Loosen the four fastening screws (2) on each side
of the head covers (1) to remove the covers.
3. Loosen the four fastening screws (4) on back cover
of the head (3)
4. Unscrew the securing screw (5) from the
guide-pin. Its position is shown on the picture (the fan
connecting PCB (6) has to be on the right from the
securing screw (5)).
If you do not have access to the securing screw, push
the optical module (7) towards the fans. Do not touch
the plastic lenses bare hands.
DO NOT FORGET TO UNSCREW THIS SECURING
SCREW (5)!
5. Carefully take the optical module (7) out of the
guide-tubes (11) and motors (10).
To insert the optical module back
1. Connect the fixture to mains and after fixture reset
go to tab Manual Control, select item Zoom and set
it at 255 DMX.
2. Put the optical module (7) on the LED module
(12) in such a way that three guide-pins (8) aim into
guide-tubes (11) and three lead screws (9) aim into
motors (10).
3. Hold the optical module in this position and slowly
change the item Zoom from 255 DMX to 0 DMX.
Motors "draw" the optical module to the LED module
(12).
DO NOT TRY TO INSERT THE OPTICAL
MODULE BY A FORCE.
4. Run the Zoom Reset from tab Manual Control
or disconnect/connect the fixture to mains.
5. Disconnect the fixture from mains.
6. Screw the securing screw (5) back to the guide-pin.
DO NOT FORGET TO SCREW THIS SECURING
SCREW (5)!
7. Screw covers on the fixture head.
32
11.2 Disposing of the product
To preserve the environment please dispose or recycle this product at the end of its life according to the local
regulations and codes.
12. ChangeLog
This section summarizes all types of changes in the user manual.
Version of the
manual
Date of issue
Description of changes
1.1
16/12/2016
DMX protocol ver. 1.3 (added 6 DMX modes)
1.2
24/01/2017
Added Eggcrate installation
1.3
10/02/2017
DMX protocol ver. 1.4 (Pattern crossfade channel added)
1.4
27/02/2017
DMX protocol ver.1.5
1.5
24/03/2017
DMX protocol ver.1.6
1.6
20/10/2017
DMX protocol 1.7 (Parking position, Pixel index, Pixel mirror on Power ch.)
1.7
1/11/2017
Item Pixel control added to menu Personality
1.8
7/11/2017
DMX protocol 1.8 (Saving Pixel Index and pixel mirror to fixture)
1.9
07/12/2017
2° Diffuser added to Optional Accessories
2.0
15/01/2018
Optional accessories changed
33
13. Photometric diagrams
34
January 15, 2018
Copyright © 2016-2018 Robe Lighting - All rights reserved
All Specifications subject to change without notice
Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici
35
14. Appendix - DMX modes overview
Pixel modes underlined
Mode
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
DMX
Channels
Main Features
49
16-bit pan/tit
Control of three rings separately
16-bit control of four colours (R,G,B,W) on each LED ring
16-bit Dimmer
Pixel effect control (shape,speed, fade)
Flower effect control
Without control of individual pixels
27
16-bit pan/tit
Circle active zone
8-bit control of four colours (R,G,B,W) and Dimmer
Pixel effect control (shape,speed, fade)
Flower effect control
Without control of individual pixels
33
16-bit pan/tit
Circle active zone
16-bit control of four colours (R,G,B,W) and Dimmer
Pixel effect control (shape,speed, fade)
Flower effect control
Without control of individual pixels
90
16-bit pan/tit
Circle active zone
16-bit control of four individual colours (R,G,B,W) and Dimmer
Pixel effect control (shape,speed, fade)
Flower effect
Individual pixels control (R,G,B)
27
16-bit pan/tit
Selection of active zone (rings, sectors)
8-bit control of four individual colours (R,G,B,W) and Dimmer
Flower effect control
Without control of individual pixels.
47
16-bit pan/tit
Selection of active zone (rings, sectors)
16-bit control of four individual colours (R,G,B,W) and Dimmer
Pixel patterns control (shape, repeat/size, rotation, transition, fade, crossfade, colour)
Flower effect control
Without control of individual pixels
91
16-bit pan/tit
Selection of active zone (rings, sectors)
16-bit control of four individual colours (R,G,B,W) and Dimmer
Flower effect control
Individual control of pixels (R,G,B)
110
16-bit pan/tit
Selection of active zone (rings, sectors)
16-bit control of four individual colours (R,G,B,W) and Dimmer
Flower effect control
Individual control of pixels (R,G,B,W)
104
16-bit pan/tit
Selection of active zone (rings, sectors)
16-bit control of four individual colours (R,G,B,W) and Dimmer
Pixel patterns control (shape, repeat/size, rotation, transition, fade, crossfade, colour)
Flower effect control
Individual control of pixels (R,G,B)
123
16-bit pan/tit
Selection of active zone (rings, sectors)
16-bit control of four individual colours (R,G,B,W) and Dimmer
Pixel patterns control (shape, repeat/size, rotation, transition, fade, crossfade, colour)
Flower effect control
Individual control of pixels (R,G,B,W)
36
DMX protocol
Robin SPIIDER - DMX protocol
Version: 1.8 (10 modes) Mode 1 - 3-zones, Mode 2-Basic, Mode 3 -Advanced, Mode 4 -Full RGBW
1
Mode/channel
2
3
4
1
1
1
1
2
2
2
2
DMX
Value
4
5
3
4
5
3
4
5
0 - 255
Fine control of pan movement (0=default)
0 - 255
Tilt movement by 220° (128=default)
0 - 255
Fine control of tilt movement (0=default)
proportional
proportional
Tilt fine (16 bit)
4
proportional
Pan/Tilt speed , Pan/Tilt time
5
1 - 255
6
proportional
Tilt (8 bit)
3
1 - 255
6
Pan movement by 540° (128=default)
Pan Fine (16 bit)
0
6
Type of
control
Pan (8 bit)
0 - 255
3
Function
Max. speed -tracking mode (0=default)
Pan/Tilt speed
Speed from max. to min. (vector mode)
Pan/Tilt time
Time from 0.1 s to 25.5 sec.
step
proportional
proportional
Power/Special functions
6
0 -9
Reserved (0=default)
To activate following functions, stop in DMX value for at least 3 s
and shutter must be closed at least 3 sec. („Shutter,Strobe”
channel 53/27/31/31 must be at range: 0-31 DMX). Corresponding
menu items are temporarily overriden (unless otherwise stated)
10-14
15-19
20-24
25-29
30-34
35-39
40-44
45 - 49
50 -54
55 -59
60 - 64
65 - 69
70 - 74
75 - 79
80-84
85-89
90 -109
110-114
115-119
120-124
125-129
DMX input: Wired DMX
DMX input: Wireless DMX *
Graphic display ON
Graphic display OFF
RGBW colour mixing mode
CMY colour mixing mode
Pan/Tilt speed mode
Pan/Tilt time mode
Blackout while pan/tilt moving
Disabled blackout while pan/tilt moving
Dimmer curve-square law
Dimmer curve-linear
Fans mode: Auto
Fans mode: High
White point 8000K ON
White point 8000K OFF
Reserved
Kling-Net On
Kling-Net Off
Parking position On
Parking position Off
To activate following functions, stop in DMX value for at least 3
seconds (except function Pixel index and Pixel Mirror).
130 - 139 Fixture reset (except pan/tilt)
140 - 149 Pan/Tilt reset
Page 1
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
DMX protocol
150 - 159
160 - 169
170-171
172-173
174-175
176-177
178-179
180-181
182 - 199
200 - 209
210 - 221
222 - 223
224 - 225
226-236
237
238 - 255
7
7
7
Zoom reset
Flower effect reset
Tungsten effect simulation (750W) On **
Tungsten effect simulation (1000W) On **
Tungsten effect simulation (1200W) On **
Tungsten effect simulation (2000W) On **
Tungsten effect simulation (2500W) On **
Tungsten effect simulation Off
Reserved
Total fixture reset
Pixel index
Pixel mirror On
Pixel mirror Off
Reserved
Save Pixel index and mirror to fixture
Reserved
step
step
step
step
step
step
step
step
step
proportional
step
step
step
Virtual colour wheel
7
0
1-2
3-4
5-6
7-8
9-10
11-12
13-14
15-16
17-18
19-20
21-22
23-24
25-26
27-28
29-30
31-32
33-34
35-36
37-38
39-40
41-42
43-44
45-46
47-48
49-50
51-52
53-54
55-56
57-58
59-60
61-62
63-64
No function (0=default)
Filter 4 (Medium Bastard Amber)
Filter 25 (Sunset Red)
Filter 19 (Fire)
Filter 26 (Bright Red)
Filter 58 (Lavender)
Filter 68 (Sky Blue)
Filter 36 (Medium Pink)
Filter 89 (Moss Green)
Filter 88 (Lime Green)
Filter 90 (Dark Yellow Green)
Filter 49 (Medium Purple)
Filter 52 (Light Lavender)
Filter 102 (Light Amber)
Filter 103 (Straw)
Filter 140 (Summer Blue)
Filter 124 (Dark Green)
Filter 106 (Primary Red)
Filter 111 (Dark Pink)
Filter 115 (Peacock Blue)
Filter 126 (Mauve)
Filter 117 (Steel Blue)
Filter 118 (Light Blue)
Filter 122 (Fern Green)
Filter 182 (Light Red)
Filter 121 (Filter Green)
Filter 128 (Bright Pink)
Filter 131 (Marine Blue)
Filter 132 (Medium Blue)
Filter 134 (Golden Amber)
Filter 135 (Deep Golden Amber)
Filter 136 (Pale Lavender)
Filter 137 (Special Lavender)
Page 2
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
DMX protocol
*
8
8
65-66
67-68
69-70
71-72
73-74
75-76
77-78
79-80
81-82
83-84
85-86
87-88
89-90
91-92
93-94
95-96
97-98
99-100
101-102
103-104
105-106
107-108
109-110
111-112
113-114
115-116
117-118
119-120
121-122
123-124
125-126
127-128
129-130
131-132
133-235
236-245
246-255
Filter 138 (Pale Green)
Filter 798 (Chrysalis Pink)
Filter 141 (Bright Blue)
Filter 147 (Apricot)
Filter 148 (Bright Rose)
Filter 152 (Pale Gold)
Filter 154 (Pale Rose)
Filter 157 (Pink)
Filter 143 (Pale Navy Blue)
Filter 162 (Bastard Amber)
Filter 164 (Flame Red)
Filter 165 (Daylight Blue)
Filter 169 (Lilac Tint)
Filter 170 (Deep Lavender)
Filter 172 (Lagoon Blue)
Filter 194 (Surprise Pink)
Filter 180 (Dark Lavender)
Filter 181 (Congo Blue)
Filter 197 (Alice Blue)
Filter 201 (Full C.T. Blue)
Filter 202 (Half C.T. Blue)
Filter 203 (Quarter C.T. Blue)
Filter 204 (Full C.T. Orange)
Filter 219 (Fluorescent Green)
Filter 206 (Quarter C.T. Orange)
Filter 247 (Filter Minus Green)
Filter 248 (Half Minus Green)
Filter 281 (Three Quarter C.T. Blue)
Filter 285 (Three Quarter C.T. Orange)
Filter 352 (Glacier Blue)
Filter 353 (Lighter Blue)
Filter 507 (Madge)
Filter 778 (Millennium Gold)
Filter 793 (Vanity Fair)
Raw DMX
Rainbow effect (with fade time) from slow-> fast
Rainbow effect (without fade time) from slow-> fast
0 - 255
Colour saturation control - coarse 0-100% (255=default)
*
9
9
*
9
10
10
*
*
10
11
12
13
13
*
11
14
14
Colour saturation control - fine (255=default)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
0 - 255
Colour saturation control - fine (255=default)
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
proportional
proportional
proportional
proportional
proportional
0 - 255
Colour saturation control - coarse 0-100% (255=default)
proportional
Green/Magenta (16bit) - all pixels***
proportional
Blue/Yellow (8 bit) - all pixels ***
12
*
step
Green/Magenta (8 bit) - all pixels ***
11
*
step
Red/Cyan (16bit)- all pixels***
0 - 255
*
step
Red/Cyan (8 bit)- all pixels***
8
*
step
proportional
Blue/ Yellow (16bit) -all pixels***
0 - 255
Colour saturation control - fine (255=default)
White (8 bit) - all pixels
Page 3
proportional
DMX protocol
0-255
0 - 255
*
*
15
15
8
*
*
*
10
*
*
*
*
0 - 255
Colour saturation control - coarse 0-100% (255=default)
0 - 255
Colour saturation control - fine (255=default)
*
*
12
*
*
*
0 - 255
Colour saturation control - coarse 0-100% (255=default)
14
*
*
*
*
Colour saturation control - coarse 0-100% (255=default)
0 - 255
Colour saturation control - fine (255=default)
16
*
*
*
18
*
*
*
*
*
*
20
*
*
*
22
*
*
*
*
Colour saturation control - coarse 0-100% (255=default)
0 - 255
Colour saturation control - fine (255=default)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
24
*
*
*
25
*
*
*
Colour saturation control - coarse 0-100% (255=default)
0 - 255
Colour saturation control - fine (255=default)
*
proportional
proportional
proportional
Blue/Yellow (16bit)- zone 2***
proportional
White (8 bit) - zone 2
If RGBW mode is selected:
Colour saturation control - coarse 0-100% (255=default)
If CMY mode is selected:
No function
proportional
White (16 bit) - zone 2
Colour saturation control - fine (255=default)
proportional
Red/Cyan (8 bit) - zone 3***
0 - 255
*
Colour saturation control - fine (255=default)
0 - 255
0 - 255
26
proportional
Blue/Yellow (8 bit) - zone 2***
0 - 255
*
proportional
Green/Magenta (16bit)- zone 2***
0-255
*
proportional
Green/Magenta (8 bit) - zone 2***
*
*
proportional
Red/Cyan (16bit)- zone 2***
*
23
Colour saturation control - fine (255=default)
0 - 255
0 - 255
21
If RGBW mode is selected:
Colour saturation control - coarse 0-100% (255=default)
If CMY mode is selected:
No function
Red/Cyan (8 bit) - zone 2***
*
*
proportional
White (16 bit) - zone 1
*
19
proportional
White (8 bit) - zone 1
0 - 255
17
proportional
Blue/Yellow (16bit)- zone 1***
0 - 255
*
Colour saturation control - fine (255=default)
0 - 255
0-255
*
proportional
Blue/Yellow (8 bit) - zone 1***
*
*
proportional
Green/Magenta (16bit)- zone 1***
*
15
proportional
Green/Magenta (8 bit) - zone 1***
0 - 255
13
proportional
Red/Cyan (16bit)- zone 1***
*
*
Colour saturation control - fine (255=default)
Red/Cyan (8 bit) - zone 1***
*
11
proportional
White (16 bit) - all pixels
0 - 255
9
If RGBW mode is selected:
Colour saturation control - coarse 0-100% (255=default)
If CMY mode is selected:
No function
Colour saturation control - coarse 0-100% (255=default)
proportional
Red/Cyan (16bit)- zone 3***
0 - 255
Colour saturation control - fine (255=default)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
proportional
Green/Magenta (8 bit) - zone 3***
*
Page 4
proportional
DMX protocol
27
28
*
*
*
*
Green/Magenta (16bit)- zone 3***
*
0 - 255
Colour saturation control - fine (255=default)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
Blue/Yellow (8 bit) - zone 3***
*
29
*
*
*
30
*
*
*
0 - 255
*
12
16
proportional
If RGBW mode is selected:
Colour saturation control - coarse 0-100% (255=default)
If CMY mode is selected:
No function
proportional
White (16 bit) - zone 3
*
0 - 255
32
Colour saturation control - fine (255=default)
White (8 bit) - zone 3
0-255
*
proportional
Blue/Yellow (16bit)- zone 3***
0 - 255
31
proportional
Colour saturation control - fine (255=default)
proportional
CTC
16
If function "White Point 8000K" is ON
33
13
17
0-255
Col. temperature correction from 8000K to 2700K -for whites only
proportional
0-255
(0=8000K, 64=5600K, 128=4200K, 192=3200K, 255=2700K)
To get colour temperatures stated above, RGBW channels have to
be set at the same value (e.g. 255DMX) or RGB=0 and White
channel > 0 DMX (0=default)
(To activate Tungsten effect at 2700K and 3200K , set DMX value at
"Power/Special functions" channel)
If function "White Point 8000K" is OFF
Colour temperature correction from cool col. to warm colours
proportional
Colour Mix control
17
The channel defines relation between color channels
IF Flower effect is active, its colour channels always have priority!
Global = Global Colours (RGBW, Virtual Colour Wheel)
Pixel = Pixel Colours (RGB individual pixels or Kling-Net)
0-9
Global colours (Global has priority)
10-19 Maximum mode (highest values have priority)
20-29 Minimum mode (lowest values have priority)
30-39 Multiply mode (multiply Global and Pixel)
40-49 Addition mode (Global + Pixel)
(45=default)
50-59 Subtraction mode (Global – Pixel)
60-69 Inverted Subtraction mode (Pixel – Global)
70-79 Coloured background
80-127 Raw DMX
128
Global colours only (Global has priority)
129-254 Crossfade (crossfade between Global and Pixel)
255
Pixel colours (Pixel has priority)
34
14
18
15
19
step
step
step
step
step
step
proportional
step
proportional
step
Pixel effects
18
0-2
3-4
5-6
:
181-182
183-255
35
step
No function (0=default)
Effect 1
Effect 2
:
Effect 90
Raw DMX
step
step
:
step
proportional
Pixel effects speed
19
0-127
Speed from from min. to max. (0=default)
Page 5
proportional
DMX protocol
128-255 Speed from max. to min. (opposite direction)
36
16
20
0
1-255
37
17
21
0
1 - 127
128
129-255
18
22
22
39
19
23
23
20
24
21
25
25
42
22
26
26
Open position-without Flower Effect (0=default)
Flower Effect forwards rotation from fast to slow
Flower Effect -without rotation
Backwards rotation from slow to fast
step
proportional
step
proportional
Colour saturation control - coarse 0-100% (255=default)
proportional
Flower Effect - Green (8 bit)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
proportional
Flower effect - Blue (8 bit)
24
41
step
proportional
Flower Effect - Red (8 bit)
0 - 255
40
Without fade time (0=default)
Fade time from min. to max.
Flower Effect
21
38
proportional
Pixel effects fade
20
proportional
Flower Effect - White (8 bit)
0-255
Colour saturation control - coarse 0-100% (255=default)
proportional
Flower Effect - colour macros
(Flower Effect channel has to be set > 0 DMX)
0
step
Open position - without macros (0=default)
(Flower effect colour macros have priority to RGBW colours/Virtual colour
wheel,Flower effect colours )
Flower Effect colour macro 1
Flower Effect colour macro 2
Flower Effect colour macro 3
:
119-120 Flower Effect colour macro 60
121-255 Raw DMX
1-2
3-4
5-6
43
23
27
0 - 31
32 - 63
64 - 95
96 - 127
128 - 143
144 - 159
160 - 191
192 - 223
224 - 255
24
28
28
45
25
29
29
47
*
26
30
31
step
step
proportional
Shutter closed
Shutter open (32=default)
Strobe-effect from slow to fast
Shutter open
Opening pulse in sequences from slow to fast
Closing pulse in sequences from fast to slow
Shutter open
Random strobe-effect from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
Flower Effect - Dimmer intensity (8 bit)
0 - 255
46
step
Flower Effect - Shutter/ strobe
27
44
step
Dimmer intensity from 0% to 100% (0=default)
proportional
Zoom
0-255
Zoom from max. to min.beam angle (128=default)
0-255
Fine zooming (0=default)
proportional
Zoom - fine
30
proportional
Shutter/ strobe
31
0 - 31
32 - 63
64 - 95
96 - 127
128 - 143
Shutter closed
Shutter open (32=default)
Strobe-effect from slow to fast
Shutter open
Opening pulse in sequences from slow to fast
Page 6
step
step
proportional
step
proportional
DMX protocol
144 - 159
160 - 191
192 - 223
224 - 255
48
27
32
32
49
*
33
33
*
*
*
*
*
*
*
*
Fine dimming (0=default)
0-255
Red LED saturation control 0-100% (0=default)
0-255
Green LED saturation control 0-100% (0=default)
*
*
*
89
*
*
*
90
step
proportional
proportional
proportional
Green pixel 1
proportional
Blue pixel 1
0-255
88
proportional
Red pixel 1
36
*
Dimmer intensity from 0% to 100% (0=default)
0 - 255
35
*
step
Dimmer intensity - fine (16 bit)
34
*
proportional
Dimmer intensity (8 bit)
0 - 255
*
Closing pulse in sequences from fast to slow
Shutter open
Random strobe-effect from slow to fast
Shutter open
Blue LED saturation control 0-100% (0=default)
:
proportional
Red pixel 19
0-255
Red LED saturation control 0-100% (0=default)
proportional
Green pixel 19
0-255
Green LED saturation control 0-100% (0=default)
proportional
Blue pixel 19
0-255
Blue LED saturation control 0-100% (0=default)
* function is active only 10 seconds after switching the fixture on
** In the Tungsten effect simulation the Dimmer channel imitates behaviour of the halogen lamp during dimming
*** Select RGB or CMY mixing mode on channel "Power/Special functions"
Copyright © 2016-2017 Robe Lighting s.r.o. - All rights reserved
All Specifications subject to change without notice
Page 7
proportional
DMX protocol
Robin SPIIDER - DMX protocol
Version: 1.8 (10 modes)
5
6
1
1
2
3
2
3
Mode/channel
7
8
9
1
2
3
1
2
3
1
2
3
Mode 5-Wash, Mode 6-Pattern, Mode 7-Pixel RGB, Mode 8-Pixel RGBW, Mode 9-Pattern full RGB, Mode 10-Pattern full RGBW
10
DMX
Value
0 - 255
Pan movement by 540° (128=default)
0 - 255
Fine control of pan movement (0=default)
0 - 255
Tilt movement by 220° (128=default)
4
4
4
5
5
5
5
5
5
1 - 255
1 - 255
6
6
6
Fine control of tilt movement (0=default)
proportional
Pan/Tilt speed , Pan/Tilt time
0
6
proportional
Tilt fine (16 bit)
0 - 255
6
proportional
Tilt (8 bit)
3
4
proportional
Pan Fine (16 bit)
2
4
Type of
control
Pan (8 bit)
1
4
Function
Max. speed -tracking mode (0=default)
Pan/Tilt speed
Speed from max. to min. (vector mode)
Pan/Tilt time
Time from 0.1 s to 25.5 sec.
step
proportional
proportional
Power/Special functions
6
0 -9
10-14
15-19
Reserved (0=default)
To activate following functions, stop in DMX value for at least 3 s
and shutter must be closed at least 3 sec. („Master Shutter/Strobe”
channel 26/45/32/32/45/45 must be at range: 0-31 DMX).
Corresponding menu items are temporarily overriden ( unless
otherwise stated)
DMX input: Wired DMX
DMX input: Wireless DMX *
step
step
* function is active only 10 seconds after switching the fixture on
20-24
25-29
30-34
35-39
40-44
45-49
50-54
55-59
60-64
65-69
70-74
75-79
80-84
85-89
90-109
110-114
115-119
120-124
125-129
Graphic display ON
Graphic display OFF
RGBW colour mixing mode
CMY colour mixing mode
step
Pan/Tilt speed mode
Pan/Tilt time mode
Blackout while pan/tilt moving
Disabled blackout while pan/tilt moving
Dimmer curve-square law
Dimmer curve-linear
Fans mode: Auto
Fans mode: High
White point 8000K ON
White point 8000K OFF
Reserved
Kling-Net On
Kling-Net Off
step
Parking position On
Parking position Off
To activate following functions, stop in DMX value for at least 3
seconds (except function Pixel index and Pixel mirror).
step
130 - 139 Fixture reset (except pan/tilt)
Page 1
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
DMX protocol
5
6
Mode/channel
7
8
9
10
DMX
Value
Function
140 - 149
150 - 159
160 - 169
170-171
172-173
Pan/Tilt reset
Zoom reset
Flower effect reset
Tungsten effect simulation (750W) On **
Tungsten effect simulation (1000W) On **
174-175 Tungsten effect simulation (1200W) On **
176-177 Tungsten effect simulation (2000W) On **
178-179 Tungsten effect simulation (2500W) On **
180-181 Tungsten effect simulation Off
182 - 199 Reserved
200 - 209 Total fixture reset
210 - 221 Pixel index
222 - 223 Pixel mirror On
224 - 225 Pixel mirror Off
226-236 Reserved
237
Save Pixel index and mirror to fixture
238 - 255 Reserved
7
7
7
7
7
Type of
control
step
step
step
step
step
step
step
step
step
step
proportional
step
step
step
Background - Virtual colour wheel
7
0
1-2
3-4
5-6
7-8
9-10
11-12
13-14
15-16
17-18
19-20
21-22
23-24
25-26
27-28
29-30
31-32
33-34
35-36
37-38
39-40
41-42
43-44
45-46
47-48
49-50
51-52
53-54
55-56
57-58
No function (0=default)
Filter 4 (Medium Bastard Amber)
Filter 25 (Sunset Red)
Filter 19 (Fire)
Filter 26 (Bright Red)
Filter 58 (Lavender)
Filter 68 (Sky Blue)
Filter 36 (Medium Pink)
Filter 89 (Moss Green)
Filter 88 (Lime Green)
Filter 90 (Dark Yellow Green)
Filter 49 (Medium Purple)
Filter 52 (Light Lavender)
Filter 102 (Light Amber)
Filter 103 (Straw)
Filter 140 (Summer Blue)
Filter 124 (Dark Green)
Filter 106 (Primary Red)
Filter 111 (Dark Pink)
Filter 115 (Peacock Blue)
Filter 126 (Mauve)
Filter 117 (Steel Blue)
Filter 118 (Light Blue)
Filter 122 (Fern Green)
Filter 182 (Light Red)
Filter 121 (Filter Green)
Filter 128 (Bright Pink)
Filter 131 (Marine Blue)
Filter 132 (Medium Blue)
Filter 134 (Golden Amber)
Page 2
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
DMX protocol
5
8
6
8
Mode/channel
7
8
9
8
8
8
10
DMX
Value
59-60
61-62
63-64
65-66
67-68
69-70
71-72
73-74
75-76
77-78
79-80
81-82
83-84
85-86
87-88
89-90
91-92
93-94
95-96
97-98
99-100
101-102
103-104
105-106
107-108
109-110
111-112
113-114
115-116
117-118
119-120
121-122
123-124
125-126
127-128
129-130
131-132
133-235
236-245
246-255
Filter 135 (Deep Golden Amber)
Filter 136 (Pale Lavender)
Filter 137 (Special Lavender)
Filter 138 (Pale Green)
Filter 798 (Chrysalis Pink)
Filter 141 (Bright Blue)
Filter 147 (Apricot)
Filter 148 (Bright Rose)
Filter 152 (Pale Gold)
Filter 154 (Pale Rose)
Filter 157 (Pink)
Filter 143 (Pale Navy Blue)
Filter 162 (Bastard Amber)
Filter 164 (Flame Red)
Filter 165 (Daylight Blue)
Filter 169 (Lilac Tint)
Filter 170 (Deep Lavender)
Filter 172 (Lagoon Blue)
Filter 194 (Surprise Pink)
Filter 180 (Dark Lavender)
Filter 181 (Congo Blue)
Filter 197 (Alice Blue)
Filter 201 (Full C.T. Blue)
Filter 202 (Half C.T. Blue)
Filter 203 (Quarter C.T. Blue)
Filter 204 (Full C.T. Orange)
Filter 219 (Fluorescent Green)
Filter 206 (Quarter C.T. Orange)
Filter 247 (Filter Minus Green)
Filter 248 (Half Minus Green)
Filter 281 (Three Quarter C.T. Blue)
Filter 285 (Three Quarter C.T. Orange)
Filter 352 (Glacier Blue)
Filter 353 (Lighter Blue)
Filter 507 (Madge)
Filter 778 (Millennium Gold)
Filter 793 (Vanity Fair)
Raw DMX
Rainbow effect (with fade time) from slow-> fast
Rainbow effect (without fade time) from slow-> fast
0 - 255
Colour saturation control - coarse 0-100% (255=default)
9
9
9
9
9
9
10
10
10
10
10
*
11
11
11
11
11
Type of
control
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
proportional
proportional
proportional
Background - Red/Cyan (8 bit)***
8
*
Function
proportional
Background - Red/Cyan (16bit)***
0 - 255
Colour saturation control - fine (255=default)
proportional
Background - Green/Magenta (8 bit)***
0 - 255
Colour saturation control - coarse 0-100% (255=default)
proportional
Background - Green/Magenta (16bit) ***
0 - 255
Colour saturation control - fine (255=default)
Page 3
proportional
DMX protocol
5
6
10
12
*
11
13
14
Mode/channel
7
8
9
12
13
14
12
13
14
12
13
14
10
DMX
Value
0 - 255
Colour saturation control - coarse 0-100% (255=default)
0 - 255
Colour saturation control - fine (255=default)
0-255
0 - 255
15
15
15
12
16
16
16
16
16
proportional
Background - White (8 bit) - all pixels
14
15
proportional
Background - Blue/ Yellow (16bit)***
13
15
Type of
control
Background - Blue/Yellow (8 bit)***
12
*
Function
If RGBW mode is selected:
Colour saturation control - coarse 0-100% (255=default)
If CMY mode is selected:
No function
proportional
Background - White (16 bit) - all pixels
0 - 255
Colour saturation control - fine (255=default)
proportional
Background - CTC
If function "White Point 8000K" is ON
0-255
Col. temperature correction from 8000K to 2700K -for whites only
proportional
(0=8000K, 64=5600K, 128=4200K, 192=3200K, 255=2700K)
To get colour temperatures stated above, RGBW channels have to
be set at the same value (e.g. 255DMX) or RGB=0 and White
channel > 0 DMX (0=default)
(To activate Tungsten effect at 2700K and 3200K , set DMX value at
"Power/Special functions" channel)
0-255
13
17
17
17
17
*
15
18
19
20
18
19
20
18
19
20
18
19
20
proportional
Background - Shutter/ strobe
17
0 - 31
32 - 63
64 - 95
96 - 127
128 - 143
144 - 159
160 - 191
192 - 223
224 - 255
14
If function "White Point 8000K" is OFF
Colour temperature correction from cool col. to warm colour
Shutter closed
Shutter open (32=default)
Strobe effect from slow to fast
Shutter open
Opening pulse in sequences from slow to fast
Closing pulse in sequences from fast to slow
Shutter open
Random strobe effect from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
Background - Dimmer intensity (8 bit)
18
0 - 255
Dimmer intensity from 0% to 100% (255=default)
0 - 255
Fine dimming (255=default)
0-2
3-4
5-6
7-8
9-10
11-12
13-14
15-16
17-18
19-20
21-22
23-24
All pixels (0=default)
Ring 1 (Middle pixel)
Ring 2
Ring 3
Ring 1+ Ring 2
Ring 1+ Ring 3
Ring 2 + Ring 3
Sector 1
Sector 2
Sector 3
Sector 4
Sector 5
proportional
Background Dimmer intensity - fine (16 bit)
19
proportional
Background - Active zone
20
Page 4
step
step
step
step
step
step
step
step
step
step
step
DMX protocol
5
6
Mode/channel
7
8
9
10
DMX
Value
25-26
27-28
29-30
31-32
33-34
35-36
37-38
39-40
41-42
43-44
45-46
47-48
49-50
51-52
53-54
55-56
57-58
59-255
16
21
21
21
21
Function
Sector 6
Sector 1+4
Sector 1+4+Ring 1
Sector 2+5
Sector 2+5+Ring 1
Sector 3+6
Sector 3+6+Ring 1
Sector 1+3+5
Sector 1+3+5+Ring 1
Sector 2+4+6
Sector 2+4+6+Ring 1
Sector 1+2+3
Sector 2+3+4
Sector 3+4+5
Sector 4+5+6
Sector 5+6+1
sector 6+1+2
Raw DMX
Type of
control
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
proportional
Colour Mix control
21
The channel defines relation between color channels
IF Flower effect is active, its colour channels always have priority!
Global = Global Colours (Background RGBW, Background Virtual
Colour Wheel, Background CTC)
Pixel = Pixel Colours (RGB individual pixels or Kling-Net)
0-9
Global colours (Global has priority)
10-19 Maximum mode (highest values have priority)
20-29 Minimum mode (lowest values have priority)
30-39 Multiply mode (multiply Global and Pixel)
40-49 Addition mode (Global + Pixel)
(45=default)
50-59 Subtraction mode (Global – Pixel)
60-69 Inverted Subtraction mode (Pixel – Global)
70-79 Coloured background
80-127 Raw DMX
128
Global colours only (Global has priority)
129-254 Crossfade (crossfade between Global and Pixel)
255
Pixel colours (Pixel has priority)
17
22
22
22
22
19
23
24
23
24
23
24
23
24
25
25
25
25
21
26
26
26
26
26
Open position-without Flower Effect (0=default)
Flower Effect forwards rotation from fast to slow
Flower Effect -without rotation
Backwards rotation from slow to fast
0 - 255
Colour saturation control - coarse 0-100% (255=default)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
step
step
step
step
proportional
step
proportional
step
step
proportional
step
proportional
proportional
Flower Effect - Green/Magenta (8 bit)
24
25
step
Flower Effect - Red/Cyan (8 bit)
23
20
step
Flower Effect
22
0
1 - 127
128
129-255
18
step
proportional
Flower effect - Blue/Yellow (8 bit)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
Flower Effect - White (8 bit)
Page 5
proportional
DMX protocol
5
6
22
27
Mode/channel
7
8
9
10
DMX
Value
0-255
27
27
27
Function
Colour saturation control - coarse 0-100% (255=default)
Type of
control
proportional
Flower Effect - colour macros
27
(Flower Effect channel has to be set > 0 DMX)
0
step
Open position - without macros (0=default)
(Flower effect colour macros have priority to RGBW colours/Virtual colour
wheel,Flower effect colours, channels Flower effect-Shutter/strobe and
Flower effect-dimmer has to be open )
1-2
3-4
5-6
Flower Effect colour macro 1
Flower Effect colour macro 2
Flower Effect colour macro 3
:
119-120 Flower Effect colour macro 60
121-255 Raw DMX
23
28
28
28
28
29
29
29
29
0 - 255
30
30
30
30
30
*
31
31
31
31
31
*
32
*
*
32
32
*
33
Shutter closed
Shutter open (32=default)
Strobe-effect from slow to fast
Shutter open
Opening pulse in sequences from slow to fast
Closing pulse in sequences from fast to slow
Shutter open
Random strobe-effect from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
Dimmer intensity from 0% to 100% (255=default)
proportional
Zoom from max. to min.beam angle (128=default)
proportional
Fine zooming (0=default)
proportional
Pattern selection
0-2
3-4
5-6
7-8
9-10
11-12
13-14
15-16
17-18
19-20
21-22
23-24
25-255
*
proportional
Zoom - fine
0-255
33
step
Zoom
0-255
*
step
Flower Effect - Dimmer intensity (8 bit)
29
25
step
Flower Effect - Shutter/ strobe
28
0 - 31
32 - 63
64 - 95
96 - 127
128 - 143
144 - 159
160 - 191
192 - 223
224 - 255
24
step
No pattern (0=default)
Pattern 1
Pattern 2
Pattern 3
Pattern 4
Pattern 5
Pattern 6
Pattern 7
Pattern 8
Pattern 9
Pattern 10
Pattern 11
RAW DMX
step
step
step
step
step
step
step
step
step
step
step
proportional
Pattern - Repeat (Size)
33
0-2
3-4
5-6
7-8
Variant 1 (0=default)
Variant 2
Variant 3
Variant 4
Page 6
step
step
step
step
DMX protocol
5
*
*
6
34
35
Mode/channel
7
8
9
*
*
*
*
34
35
10
DMX
Value
9-10
11-12
13-14
15-16
17-18
19-20
21-22
23-255
Variant 5
Variant 6
Variant 7
Variant 8
Variant 9
Variant 10
Variant 11
Raw DMX
0
1-127
128-190
191-192
193-255
No rotation (0=default)
Pattern indexing
Forwards rotation from fast to slow
Pause - without rotation
Backwards rotation from slow to fast
36
*
*
36
*
*
37
*
*
38
39
40
*
*
*
*
*
*
38
39
40
*
41
41
*
42
*
*
42
42
step
step
proportional
Snap (0=default)
Fade from min. to max.
No fade (0=default)
100ms
:
4 sec
Background
Crossfade between Background and Pattern 0-100% (255=default)
Colour saturation control - coarse 0-100% (255=default)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
step
proportional
proportional
step
proportional
step
proportional
step
step
step
step
proportional
0 - 255
Colour saturation control - coarse 0-100% (255=default)
proportional
Pattern - Green (8-bit)
proportional
Pattern - Blue (8-bit)
40
*
step
0 - 255
39
41
step
Pattern - Red (8-bit)
38
*
step
Pattern - Crossfade
37
0
1-255
*
step
Pattern -Transition
36
255
37
step
Pattern - Fade
35
0
1
*
Type of
control
Pattern - Rotation
34
0
1-255
*
Function
proportional
Pattern - White (8-bit)
0 - 255
Colour saturation control - coarse 0-100% (255=default)
proportional
Pattern - Colour macro
0-2
3-8
9-14
15-20
21-26
27-32
33-38
39-44
45-50
51-56
57-62
63-68
69-74
No macro (0=default)
Macros 1-15 allow control of colour change speed from max. to min.
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Page 7
step
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
proportional
DMX protocol
5
6
Mode/channel
7
8
9
10
DMX
Value
75-80
81-86
87-92
93-98
99-104
105-110
111-255
*
43
*
*
43
0 - 31
32 - 63
64 - 95
96 - 127
128 - 143
144 - 159
160 - 191
192 - 223
224 - 255
44
*
*
44
44
26
45
32
32
45
45
46
33
33
46
47
34
34
47
47
*
*
35
35
48
48
*
*
*
*
*
36
37
*
36
37
38
49
50
*
*
*
90
108 103 121
*
*
91
109 104 122
Shutter closed
Shutter open (32=default)
Strobe effect from slow to fast
Shutter open
Opening pulse in sequences from slow to fast
Closing pulse in sequences from fast to slow
Shutter open
Random strobe effect from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
Dimmer intensity from 0% to 100% (255=default)
proportional
step
step
proportional
step
proportional
proportional
step
proportional
step
Master Dimmer intensity (8 bit)
proportional
Master Dimmer intensity - fine (16 bit)
Fine dimming (0=default)
proportional
Red pixel 1
0-255
Red LED saturation control 0-100% (0=default)
0-255
Green LED saturation control 0-100% (0=default)
0-255
Blue LED saturation control 0-100% (0=default)
proportional
Green pixel 1
proportional
Blue pixel 1
proportional
White pixel 1
0-255
107 102 120
step
proportional
Dimmer intensity from 0% to 100% (0=default)
51
89
step
0 - 255
50
*
step
Shutter closed
Shutter open (32=default)
Strobe effect from slow to fast
Shutter open
Opening pulse in sequences from slow to fast
Closing pulse in sequences from fast to slow
Shutter open
Random strobe effect from slow to fast
Shutter open
49
*
proportional
0 - 31
32 - 63
64 - 95
96 - 127
128 - 143
144 - 159
160 - 191
192 - 223
224 - 255
0 - 255
*
proportional
Master Shutter/ strobe
46
*
proportional
Pattern - Dimmer intensity (8 bit)
0 - 255
27
Macro 13
Macro 14
Macro 15
Macro 16
Macro 17
Macro 18
Raw DMX
Type of
control
Pattern - Shutter/ strobe
43
*
Function
White LED saturation control 0-100% (0=default)
:
proportional
Red pixel 19
0-255
Red LED saturation control 0-100% (0=default)
proportional
Green pixel 19
0-255
Green LED saturation control 0-100% (0=default)
proportional
Blue pixel 19
0-255
Blue LED saturation control 0-100% (0=default)
Page 8
proportional
DMX protocol
5
6
*
*
Mode/channel
7
8
9
*
110
*
10
DMX
Value
Function
Type of
control
White pixel 19
123
0-255
White LED saturation control 0-100% (0=default)
* function is active only 10 seconds after switching the fixture on
** In the Tungsten effect simulation the Dimmer channel imitates behaviour of the halogen lamp during dimming
*** Select RGB or CMY mixing mode on channel "Power/Special functions"
Copyright © 2016 -2017 Robe Lighting s.r.o. - All rights reserved
Page 9
proportional
Robin Spiider - colours on Virtual Colour Wheel
Red
Green
Blue
Colour name
(DMX)
(DMX)
(DMX)
255
118
0
Filter 4 (Medium Bastard Amber)
255
50
0
Filter 25 (Sunset Red)
255
13
0
Filter 19 (Fire)
255
0
0
Filter 26 (Bright Red)
117
0
97
Filter 58 (Lavender)
42
195
100
Filter 68 (Sky Blue)
255
74
8
Filter 36 (Medium Pink)
69
245
0
Filter 89 (Moss Green)
187
226
0
Filter 88 (Lime Green)
0
255
1
Filter 90 (Dark Yellow Green)
255
0
27
Filter 49 (Medium Purple)
227
86
14
Filter 52 (Light Lavender)
233
164
0
Filter 102 (Light Amber)
207
137
0
Filter 103 (Straw)
0
161
7
Filter 140 (Summer Blue)
29
255
0
Filter 124 (Dark Green)
242
1
1
Filter 106 (Primary Red)
255
67
11
Filter 111 (Dark Pink)
0
255
28
Filter 115 (Peacock Blue)
255
0
39
Filter 126 (Mauve)
163
255
14
Filter 117 (Steel Blue)
0
255
61
Filter 118 (Light Blue)
98
255
3
Filter 122 (Fern Green)
255
16
2
Filter 182 (Light Green)
165
255
0
Filter 121 (Filter Green)
255
0
13
Filter 128 (Bright Pink)
73
245
27
Filter 131 (Marine Blue)
0
193
113
Filter 132 (Medium Blue)
191
83
0
Filter 134 (Golden Amber)
255
52
0
Filter 135 (Deep Golden Amber)
164
96
29
Filter 136 (Pale Lavender)
130
60
63
Filter 137 (Special Lavender)
226
255
0
Filter 138 (Pale Green)
49
0
98
Filter 798 (Chrysalis Pink)
8
176
62
Filter 141 (Bright Blue)
215
104
0
Filter 147 (Apricot)
255
3
0
Filter 148 (Bright Rose)
202
115
0
Filter 152 (Pale Gold)
214
107
0
Filter 154 (Pale Rose)
255
56
5
Filter 157 (Pink)
0
193
72
Filter 143 (Pale Navy Blue)
223
153
6
Filter 162 (Bastard Amber)
255
27
0
Filter 164 (Flame Red)
23
236
87
Filter 165 (Daylight Blue)
206
123
0
Filter 169 (Lilac Tint)
235
123
41
Filter 170 (Deep Lavender)
0
255
54
Filter 172 (Lagoon Blue)
1
White
(DMX)
109
3
0
0
110
0
24
3
0
0
0
134
0
33
218
12
0
49
41
0
161
34
2
0
0
32
30
0
0
0
54
102
51
14
0
15
37
39
48
48
148
41
4
81
110
33
0
Colour name
Filter 194 (Surprise Pink)
Filter 180 (Dark Lavender)
Filter 181 (Congo Blue)
Filter 197 (Alice Blue)
Filter 201 (Full C.T. Blue)
Filter 202 (Half C.T. Blue)
Filter 203 (Quarter C.T. Blue)
Filter 204 (Full C.T. Orange)
Filter 219 (Fluorescent Green)
Filter 206 (Quarter C.T. Orange)
Filter 247 (Filter Minus Green)
Filter 248 (Half Minus Green)
Filter 281 (Three Quarter C.T. Blue)
Filter 285 (Three Quarter C.T. Orange)
Filter 352 (Glacier Blue)
Filter 353 (Lighter Blue)
Filter 507 (Madge)
Filter 778 (Millennium Gold)
Filter 793 (Vanity Fair)
Red
(DMX)
110
136
37
107
179
217
236
230
99
204
255
255
225
199
0
0
255
255
255
2
Green
(DMX)
0
43
0
220
255
255
255
125
148
140
81
144
255
124
161
115
31
65
0
Blue
(DMX)
21
181
255
129
57
37
30
3
16
0
0
0
72
0
65
37
0
0
13
White
(DMX)
255
89
0
0
34
3
3
7
50
57
193
137
160
17
90
97
0
0
16
Download PDF
Similar pages