E11
1MP Cube with Basic WDR, Fixed lens
Hardware User’s Manual
(PoE)
Ver. 2012/10/22
E11 Hardware User’s Manual
Table of Contents
0.
Precautions
3
1.
Introduction
4
Package Contents ........................................................................... 4
Features and Benefits ..................................................................... 5
Safety Instructions .......................................................................... 6
Physical description ........................................................................ 8
Basic Connections ........................................................................... 9
Product Specification .................................................................... 10
2.
Accessing Camera
11
If you have DHCP server / router in your network: ...................... 11
If you do NOT have DHCP server / router in your network: ......... 11
2
www.acti.com
E11 Hardware User’s Manual
0. Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to
follow the safety instruction given may directly endanger people, cause damage to the system
or to other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the users will be required to correct the
interference at their own expense.
3
www.acti.com
E11 Hardware User’s Manual
1. Introduction
Package Contents
E11
Camera Stand
Accessories
Warranty Card
QIG
4
www.acti.com
E11 Hardware User’s Manual
Features and Benefits
This is a cutting-edge digital video surveillance camera. It can compress and transmit real time
images with outstanding image quality through a standard TCP/IP network. This camera is
your best choice to build an intelligent IP surveillance system.
H.264 High Profile/MJPEG Multi-Codec Dual Streaming
This device supports 2 compression formats, H.264 High Profile and MJPEG. It brings superior
image quality at 30 frames per second up to a resolution of 720p (1280 x 720) pixels and VGA
(640 x 480) pixels.
Built-in Hardware Motion Detection
No more external motion sensors are required. You may assign up to 3 video motion detection
areas. By tuning the object size and sensitivity, it will reliably detect objects passing though is
view. Hardware motion detection also offers better sensitivity and faster response time than
software motion detection.
Powerful Bundled Surveillance Software
To extend the capabilities of the IP Camera series, a powerful surveillance program is included
in the package for free. Users can easily use an existing PC as a digital video recorder.
Scheduled recording and manual recording keep every important video recorded in the local
hard disk. Reliable and accurate motion detection with instant warning enables immediate
response in every condition. Quick and simple search and playback function lets you easily find
the images and video you want.
Software Development Kit Support
This IP Camera can be integrated or controlled by applications from third party software
developers. Software developers can save considerable efforts by using our Streaming Library
or ActiveX control. Please contact us for details on integration support.
5
www.acti.com
E11 Hardware User’s Manual
Safety Instructions
Don’t open the housing of the product
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may
cause hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool and the like.
Don’t use accessories not recommended by the manufacturer
Only install this device in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to
qualified service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in
this manual. Adjust only those controls that are covered by the instruction manual, as an
improper adjustment of other controls may result in damage, and will often require
extensive work by a qualified technician to restore the video product to its normal
operation.
6
www.acti.com
E11 Hardware User’s Manual
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
7
www.acti.com
E11 Hardware User’s Manual
Physical description
1) Built-in Microphone
2) Audio Output
The IP device supports audio output with earphone jack
3) Reset Button
Step 1: Press and continue to hold the Reset Button for 15 seconds (with a sharp tipped object,
like a pen.) after the unit has successfully completed the boot process.
Step 2: The Ethernet LED light will turn off for about 1~2 seconds and flash on for another
second. By this time the reset to default operation is already completed. You may then release
the reset button. This length of time fluctuates slightly with the environment. The unit will come
back on and stay on after a few more seconds. The unit will start up with factory default
settings automatically.
4) Ethernet Port
The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this
IP device can auto detect the speed of local network segment (10Base-T/100Base-TX
Ethernet).
8
www.acti.com
E11 Hardware User’s Manual
Basic Connections
Follow the procedures below to connect the IP device to the respective apparatuses.
Please use a PoE (Power over Ethernet) supported switch or injector:
1) Connect your IP Camera to the PoE Switch / Injector by CAT5 or CAT6 cables with RJ45
connector.
2) Connect your PoE Switch / Injector to PC with another CAT5 / CAT6 network cable.
9
www.acti.com
E11 Hardware User’s Manual
Product Specification
E11
• Device
Device Type
Image Sensor
Day / Night
Minimum Illumination
Mechanical IR Cut Filter
IR Sensitivity Range
Electronic Shutter
Cube Camera
Progressive Scan CMOS
No
Color: 0.1 lux at F1.8 (30 IRE, 2400 °K)
No
No
1/5 - 1/2,000 sec (Manual / Auto mode)
• Lens
Focal Length / Aperture
Iris
Focus
Mount Type
Horizontal Viewing Angle
Fixed focal, f4.2 mm / F1.8
Fixed iris
Manual focus
CS Mount (interchangeable lens)
57.8°
• Video
Compression
Maximum Frame Rate
vs. Resolution
Multi-Streaming
Bit Rate
Bit Rate Mode
Image Enhancement
Privacy Mask
Text Overlay
Image Orientation
• Audio
Compression
Audio-In
Audio-Out
• Network
Protocol & Service
Ethernet Port
Security
• Alarm
Alarm Trigger
Alarm Response
• General
Power Source / Consumption
Weight
Dimensions (Φ x H)
Bundled Accessories
Mount Type
Operating Temperature
Operating Humidity
Approvals
• Integration
Unified Solution
ISV Integration
Firmware Access Browser
H.264 HP, MJPEG
30 fps at 1280 x 720 (HD 720p); 30 fps at 640 x 480 (VGA)
Simultaneous dual streams based on two configurations
28 Kbps - 6 Mbps (per stream)
Constant, Variable
Basic WDR; White balance: automatic, hold, and manual; Brightness;
Contrast; Automatic gain control; Digital noise reduction; Flickerless
4 configurable regions
User defined text on video
Image flip and mirror
8kHz, Mono, PCM,16 bit encoding; G.711
Built-in Microphone
3.5mm Phone Jack
TCP, UDP, HTTP, HTTPS, DHCP, PPPoE, RTP, RTSP, IPv6, DNS, DDNS, NTP, ICMP, ARP, IGMP, SMTP, FTP,
UPnP, SNMP, Bonjour
1, Ethernet (10/100 Base-T), RJ-45 connector
IP address filtering; HTTPS encryption; Password protected user levels; IEEE 802.1X network access control
Video motion detection (3 regions)
Notify control center; Change camera settings; Command other devices;
E-mail notification with snapshots; Upload video, snapshot to FTP server
PoE Class 2 (IEEE802.3af) / 3.15 W
205 g (0.45 lb)
96 mm x 96 mm x 45.07 mm (3.8" x 3.8" x 1.8")
Bracket
Wall, Ceiling
-10 °C ~ 45 °C (14 °F ~ 113 °F)
10% ~ 85% RH
CE, FCC
Fully compatible with ACTi software
Software Development Kit (SDK) available; ONVIF compliant
Microsoft Internet Explorer 6.0 or newer
10
www.acti.com
E11 Hardware User’s Manual
2. Accessing Camera
If you have DHCP server / router in your network:
Many network server / routers are able to automatically provide IP addresses through DHCP. If
you are using such a network, just plug in your computer and IP Camera into the network and
your IP device will acquire network address by itself. Find and access the device with our IP
Utility program. You may download it at:
http://www.acti.com/product/detail/Software/ACTi_Utility_Suite
If you do NOT have DHCP server / router in your
network:
1. Configure your PC to use the same subnet by changing your PC’s IP address to the
subnet with prefix 192.168.0.XXX. The last number should be anything from 1 to 254
except 100 and other occupied IP addresses. Subnet mask should be 255.555.255.0.
2. The default IP used by this device is 192.168.0.100. Please make sure your PC is
NOT using this address and that no two equipments use the same IP address in
the network.
3. Change your IP address by going to Control Panel ->Manage Network Connections ->
Right click on the connection to change -> Option -> TCP/IP IPv4 Properties.
11
www.acti.com
E11 Hardware User’s Manual
Please set the settings as below.


IP address: 192.168. 0.xxx

Subnet mask: 255.255.255.
0
(NOTE: xxx should be a number
from 1 to 254 except 100, which is
used by the IP device. Please also
make sure that no two equipments
use the same IP address in the
same network..)
4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP:
192.168.0.100
5. When you see the login window, please input default user and password:
Default User: Admin
12
Password: 123456
www.acti.com
E11 Hardware User’s Manual
6. After logging in, you will see the video from camera. To go to the main menu, click the
“Setup” button on the top left.
If you are using a single camera, this is enough to access the device.
If you are using multiple devices, you need to change the current device to another
unused IP address, so that when the next device is connected to the network, no two
devices use the same IP. Please perform the following steps.
7. Go to IP Settings -> Connection Type
8. Change the IP mode to Static.
9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP
address or 192.168.0.100.). If this is not the first device you add to the network, please
also avoid other devices’ IPs.
13
www.acti.com
E11 Hardware User’s Manual
10. Click “Apply”
11. Please go to System -> Save & Reboot, and click “Apply”. Internet Explorer will close
after a few seconds. This is normal.
12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example,
192.168.0.101). For the second device or more you add into the network, please type
the correct IP.
13. Adjust the default Video setting by going to Video -> Video
Please refer the firmware manual for the detail information.
14
www.acti.com