Magnum 650 Magnum 850 user manual

P/N 35010029-F
Magnum 650
Magnum 850
user manual
Safety information...................................................................................................................... 3
Product overview ....................................................................................................................... 6
Product description................................................................................................................ 6
Features at a glance .............................................................................................................. 6
Product details – Magnum 650 .............................................................................................. 7
Product details – Magnum 850Quick Start ............................................................................ 8
Quick Start ............................................................................................................................. 9
Setting up............................................................................................................................... 9
Making fog ............................................................................................................................. 9
Installation and setting up ....................................................................................................... 10
Location ............................................................................................................................... 10
AC power ............................................................................................................................. 10
Setting up............................................................................................................................. 11
Final checks ......................................................................................................................... 12
Turning on the power........................................................................................................... 12
Operating with remote ......................................................................................................... 12
Priming the machine after fluid out ...................................................................................... 13
What the status lights mean................................................................................................. 13
Optional accessories ............................................................................................................... 14
Timer remote (Magnum 850 only) ....................................................................................... 14
Manual firing ........................................................................................................................ 14
Setting fog output level ........................................................................................................ 15
Setting the Automatic Timer ................................................................................................ 15
Setting the “one-shot” timer................................................................................................. 15
Disabling timer mode........................................................................................................... 16
Meaning of remote control lights ......................................................................................... 16
Fog fluid types ......................................................................................................................... 17
Basic service............................................................................................................................ 18
Cleaning............................................................................................................................... 18
Fuse replacement ................................................................................................................ 18
Troubleshooting ...................................................................................................................... 19
Specifications .......................................................................................................................... 20
2
Safety information
Safety information
The following symbols are used to identify important safety information:
Caution! Safety
hazard. Risk of
personal injury.
Caution! Burn
hazard. Hot
surface. Do not
touch.
Danger!
Hazardous
voltage. Contact
will cause electric
shock.
Caution! Fire
hazard.
Warning! This product is not for household use. It presents risks of injury due to
electric shock, burns, falls and respiratory problems!
Read this manual before operating the machine, follow the safety precautions
listed below, and observe all warnings in this manual and printed on the
machine. Use the system only as described in this manual and in accordance
with local laws and regulations.
If you have questions about how to operate the machine safely, or if you have
followed the instructions in this manual and the machine is malfunctioning,
please contact Martin Service.
Preventing electric shocks
•
Always ground (earth) the machine electrically.
•
Use only a source of AC power that complies with local building and
electrical codes, and that has both overload and ground-fault protection.
•
Before connecting the Magnum smoke machine to power, check that
the voltage indicated on the machine’s serial label matches your local
AC power voltage. If your AC power voltage does not match, do not use
the machine. Contact Martin Service for assistance.
•
Before using the machine, check that all power distribution equipment
and cables are in perfect condition and rated for the current
requirements of all connected devices.
•
If the machine or any cables connected to it are in any way damaged,
defective, wet, or show signs of overheating, stop using the machine
and contact Martin Service for assistance.
•
Disconnect the machine from AC power before servicing and when not
in use.
•
This system is not waterproof and should not be exposed to wet
outdoor conditions. Do not immerse in water or any other liquid. Do not
expose to high-pressure water jets.
•
Do not spill fluid over or inside the machine. If fluid is spilled, disconnect
AC power and clean with a damp cloth. If fluid is spilled onto electronic
parts, take the system out of service and contact Martin for advice.
•
Do not remove the covers or attempt to repair a faulty machine. Refer
any service not described in this manual to Martin.
Safety information
3
•
Do not operate the machine if any parts are damaged, defective or
missing.
•
Moisture and electricity do not mix. Do not aim smoke output at
electrical connections or devices.
•
If the supply cord is damaged, it must be replaced by a special cord or
assembly available from the manufacturer or its service agent.
Preventing burns and fire
•
The smoke produced by the machine is hot enough to cause burns
when it leaves the nozzle, and very hot droplets of fluid escape
occasionally. Keep people and objects at least 1 meter (39 inches) away
from the smoke output nozzle.
•
Do not touch the smoke output nozzle during or after use – it becomes
extremely hot and remain hot for several hours after the machine has
been shut down.
•
Smoke output contains glycol, a flammable alcohol that burns with an
almost invisible blue flame. Do not point smoke output at sources of
ignition such as open flames or pyrotechnic effects.
•
Do not attempt to bypass thermostatic switches, fluid sensors or fuses.
•
Replace fuses only with ones of the type and rating specified in this
manual for the machine.
•
Provide a minimum free space of 100mm (4 inches) around the
machine.
•
Provide a minimum free space of 500mm (20 inches) around fans and
air vents and ensure free and unobstructed air flow to and around the
machine.
•
Keep the machine at least 600mm (24 inches) away from combustible
and heat-sensitive materials.
•
Do not operate the machine if the ambient temperature (Ta) is below 5°
C (41° F) or above 40° C (104° F).
•
Do not operate the machine if the relative air humidity exceeds 80%.
Preventing injuries
4
•
Ensure that the surface on which the machine is located or installed can
safely hold the weight of the machine.
•
This appliance is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
•
Do not install the machine over areas where people are present.
•
Verify that the machine’s temperature setting is suitable for the type of
fluid in use whenever changing fluid or resetting the default menu
values.
•
Smoke machines can cause condensation. Do not point the output at
smooth floors. Floors and surfaces may become slippery. Check these
frequently and wipe dry as necessary to avoid any danger of slipping.
•
Ensure at least 2m visibility in areas where smoke is being produced.
Safety information
•
Smoke fluid contains food-grade glycols in solution but may present
health risks if swallowed. Do not drink it. Store it securely. If eye contact
occurs, rinse with water. If fluid is swallowed, give water and obtain
medical advice.
Preventing breathing problems
•
A smoke machine can operate safely only with the smoke fluid it is
designed for. Use the machine only with fluids specified under “Smoke
fluid options” on page 17 or you may cause the release of toxic gases,
presenting a severe health hazard. You will also probably damage the
machine.
•
Do not create dense smoke in confined or poorly ventilated areas.
•
Do not expose people with health problems (including allergic and/or
respiratory conditions such as asthma) to smoke output.
•
Do not point smoke output directly at a person’s face or at face height.
Safety information
5
Product overview
Product description
The Magnum 850 and Magnum 650 smoke machines from Martin provide a
uniquely flexible and convenient solution to a wide range of smoke requirements
whether permanently installed or taken on the road.
The machines feature a unique new design that encompasses what the
Magnum range is all about: state of the art technology, high quality and
ruggedness.
The Magnum 650 delivers a heavy punch of fog. It’s tough and rugged enough
to meet the demand of mobile discos and parties.
The Magnum 850 is a higher power fogger suitable for larger venues or night
clubs.
This manual contains instructions for both the Magnum 650 and
Magnum 850 machines. Where the Magnum 850 is different, you will
see this symbol.
Congratulations on your purchase of the Magnum smoke machine from Martin.
Details of the full range of Martin products are available on our website at
www.martin.com.
Features at a glance
6
•
Attractive and rugged design
•
Machine to machine link (Magnum 850 only)
•
Continuous operation (at reduced output) (Magnum 850 only)
•
730W (Magnum 650) / 790W (Magnum 850)
•
1 litre fluid capacity
•
Pushbutton remote control (hardwired on Magnum 650)
•
Optional timer remote (Magnum 850 only)
•
Thermal fault protection device
Product overview
Product details – Magnum 650
Carry handle
Power switch
Fluid container
Remote
cable
Power inlet plug
and mains fuse
Fluid level viewer
Smoke output
nozzle
WARNING HIGH
TEMPERATURE
VAPOUR AND
SURFACES
Product overview
7
Product details – Magnum 850
Heat (Red) /
Ready (Green)
indicators
Remote /
machine link
sockets
(Magnum
850 only)
Main power
switch
Power inlet
plug
Fluid container
Fluid level viewer
Smoke output
nozzle
WARNING HIGH
TEMPERATURE
VAPOUR AND
SURFACES
8
Quick Start
You are no doubt eager to switch on the machine and try it out by making a lot
of fog. This section tells you how to do that. However, please also make the time
to read the safety and servicing instructions in the remainder of this manual.
Setting up
Locate the machine in a suitably large area with nothing in front of the smoke
output.
Fill the fluid tank with MARTIN/JEM approved fluid (see page 17).
Connect a suitably rated power supply to the machine. The power requirements
are:
Magnum 650: 2.66A at 230V (EU) or 6.1A at 120V (US)
Magnum 850: 3.4A at 230V (EU) or 6.6A at 120V (US)
Turn the machine on, the on/off button and the remote control light will
illuminate. From cold the machine will take approximately five minutes to reach
operating temperature. When the light on the remote control has
gone out the machine is ready to use. When the light on the remote control
comes on again it indicates that the machine is reheating, this will take
approximately two minutes.
If using the Magnum 850 connect the remote control to the REMOTE
IN connector on the rear panel. The remote control is permanently
connected to the Magnum 650. Turn on the power switch. The red
Heat indicator on the remote and the top of the unit will light. After
about 7-10 minutes the green Ready indicator on the remote and the
top of the unit will light. The machine is then ready to produce fog. To
obtain maximum fog output wait another couple of minutes for the
Heat indicator to go out.
Making fog
Once the machine has heated up, hold the button on the remote to start the fog
output.
9
Installation and setting up
DANGER! DO NOT operate the Magnum smoke machine until you have read
and observed all the precautions listed under “Safety information” on page 3.
Location
The Magnum smoke machine should be located on the floor or a suitably robust
surface.
The machine can operate in any orientation from 45 degrees upwards to 45
degrees downwards. Steeper tilting may cause fluid leakage.
Do not suspend the machine over areas where people will be underneath.
Ensure that there is at least 100mm clearance all round the machine and at least
600mm in front of the smoke output.
AC power
Before using the machine, ensure that a grounding-type (earthed) power plug
that fits the local power outlets is installed on the power cable.
DANGER! Make sure the power plug is correctly rated:
• For EU (230V) use fit a plug rated 6 amp minimum
• US (120V) models must be fitted with a plug rated 10 amp minimum
When installing the plug, follow the plug manufacturer’s instructions and
connect pins as follows:
yellow and green wire to ground (earth), blue wire to neutral and brown wire to
live.
The table below shows some common pin identification schemes.
wire
function
marking
screw colour
brown
live
“L”
yellow or brass
blue
neutral
“N”
silver
green/yellow
earth
green
Before connecting the Magnum smoke machine to power, verify that the AC
supply is adequately dimensioned for the current draw of the machine. The
machine requires:
Magnum 650: 2.66A at 230V (EU) or 6.1A at 120V (US)
Magnum 850: 3.4A at 230V (EU) or 6.6A at 120V (US)
Check that the local AC voltage is appropriate, as indicated on the machine’s
serial number label. If your AC voltage is outside the appropriate range, do not
use the machine. Contact Martin Service for assistance.
10
Installation and setting up
Setting up
Fill the fluid container with MARTIN-approved fluid (see page 17).
If using the Magnum 850 connect the remote control to the REMOTE
IN connector on the rear panel. The remote control is permanently
connected to the Magnum 650.
If you are operating several machines using the machine-to-machine link
function, connect up the machines in a daisy-chain using RJ45 (computer
network) type cables. The maximum total length of cable, including the remote
cable, is 50 metres.
Machine-to-machine link is not available on the Magnum 650.
to additional
machines
Do not connect a computer network to the RJ45 remote / link sockets on the
Magnum 850. Although the connectors are compatible, the electrical signals are
not, and equipment may be damaged.
Installation and setting up
11
Final checks
Before applying power to the Magnum smoke machine, verify the following:
• the machine is safely located or installed and meets the location
requirements stated on page 10
•
the operator is familiar with, and able to comply with, the requirements
for safe operation listed on page 3
•
the smoke fluid is one of the genuine Martin fluids listed under “Smoke
fluid options” on page 14
•
the machine is electrically grounded (earthed)
•
the AC power distribution circuits and lines are adequately rated for the
current load
Turning on the power
Turn on the main power switch located next to the power cable inlet. The red
Heat indicator on the remote will illuminate.
Turn on the main power switch located next to the power cable inlet.
The red Heat indicator on the remote and on top of the machine will
illuminate for about 7-10 minutes as the machine heats up to
operating temperature. When the green Ready indicator comes on,
the machine is ready to make fog.
To obtain maximum output, wait another few minutes for the red Heat
indicator to go off, as fog output is reduced while the unit is heating
up.
Operating with remote
The unit is controlled using the remote control. Press the button to generate fog.
Magnum 650
Fog button
12
Magnum 850
Fog button
Installation and setting up
Priming the machine after fluid out
If the machine runs out of fluid it may not pump properly after refilling the fluid
due to airlocks in the fluid pipework.
To prime the machine, hold down the FOG button and keep the button held until
the fog output is strong and steady.
If the machine is left to run when out of fluid, damage will be caused to the pump
which may cause premature pump failure.
What the status lights mean
The red heat light on the remote control has the following meanings.
on
Machine is heating but is not yet up to operating
temperature
off
Machine is either ready to fire or not powered (check
mains switch light for status)
The red/green Heat / Ready lights on the top of the machine have the
following meanings.
HEAT+READY
meaning
no lights
Machine is not powered
heat
Machine is heating but is not yet up to operating
temperature
heat + ready
Machine is heating and has reached minimum operating
temperature. Fog output level may be reduced while
heating
ready
Machine has finished heating and is at full operating
temperature
Installation and setting up
13
Optional accessories (Magnum 850 only)
Timer remote
The timer remote is an optional accessory for the Magnum 850.
T
h
Output level / timer
programming knob
Machine ready to fog
light
Machine heating light
Fog / Timer engage
button
Timer Off light
Timer On light
Timer set button
The timer remote can be used in these ways:
•
Manual firing by holding down the FOG button
•
Automatic fog bursts using a repeating timer
•
You trigger a timed burst of fog using the “one-shot” timer
You can also set the fog output level using the knob.
Manual firing
Hold down the FOG button. The machine will produce fog until you release the
button.
You must hold the FOG button for one second or more. If you hold the
FOG button for less than one second, the unit will enter timer mode,
unless the timer is disabled.
If a long burst of fog is produced, after a time the fog output level will be
automatically reduced to keep the machine temperature within the operating
range. This allows continuous operation, so that the machine does not have to
stop and re-heat.
14
Optional accessories (Magnum 850 only)
Setting fog output level
Set the knob to the desired output level while firing the machine. The fog output
level is always set by the current position of the knob, whether manually firing or
in timer mode.
Setting the Automatic Timer
The Automatic Timer allows you to set the machine to keep producing timed
bursts of fog without anyone having to press any buttons. You need to set two
times: the run/on time during which the machine will produce fog, and the
wait/off time during which the machine will idle.
1. Press the TIMER SET button. The ON light will flash. You are now
setting the On/Run time.
2. Turn the knob to the required “run” time, as shown on the outer scale of
the knob (OFF – 255 seconds).
3. Press the TIMER SET button once. The ON light will come on static and
the OFF light will flash. You are now setting the Off/Wait time.
4. Turn the knob to the required “wait” time.
5. Press the TIMER SET button once more. Both ON/OFF lights will come
on to show the timer is programmed.
The run and wait times are now stored and will be remembered even after the
unit has been switched off. When valid times are stored, but the timer is not
engaged, the OFF and ON lights remain lit constantly.
To start the timer using the times you’ve set, press the FOG / TIMER ENGAGE
button briefly. To turn off the timer, press the FOG / TIMER ENGAGE button
briefly again. When the timer is engaged, the ON light will come on during the
On/Run time and the OFF light will come on during the Off/Wait time.
If you only want to change the Off/Wait time, leaving the On/Run time
unchanged, press TIMER SET twice. This will take you directly to
setting the Off time without changing the On time.
To find out what the current time settings are, press TIMER SET then rotate the
knob slowly until the “ON” light begins to flash very rapidly. The knob is now set
to the current run/on time. Press TIMER SET once and rotate the knob slowly
again until the “OFF” light begins to flash very rapidly. The knob is now set to
the current wait/off time. Press TIMER SET again to get back to normal.
Setting the “one-shot” timer
The “one shot” timer allows you to pre-program the length of the fog burst. This
can be useful if you want to have a fixed-time burst of fog which you can repeat
at will by pressing the fog button.
1. Press the TIMER SET button. The ON light will flash. You are now
setting the On/Run time.
2. Turn the knob to the required “run” time, as shown on the outer scale of
the knob (OFF – 255 seconds).
3. Press the TIMER SET button once. The ON light will come on and the
OFF light will flash.
4. Turn the knob fully right to where “OS” (“One Shot”) is marked.
5. Press the TIMER SET button once more.
Optional accessories (Magnum 850 only)
15
The timer is now programmed to one-shot mode and this will be remembered
even after the unit has been switched off.
To produce a timed burst of fog, press the FOG button briefly. To stop the timed
fog output early, press the FOG button briefly again.
Disabling timer mode
If you wish to simplify the remote control, you can disable the timer function.
This means that a short press on the FOG button will just produce a short burst
of fog and the timer will not be enabled.
1. Press the TIMER SET button once. The ON light flashes.
2. Turn the knob fully left to the “OFF” section.
3. Press the TIMER SET button again.
The zero times will be stored, disabling the timer. This will be remembered even
after the unit has been switched off. The ON and OFF lights remain off when the
timer is disabled.
To re-enable the timer function, store some non-zero times as described above.
Meaning of remote control lights
The four lights on the remote have the following functions. The red “HEAT” light
and the green “READY” light are also duplicated on the top of the machine itself.
16
HEAT+READY
meaning
no lights
Machine is not powered, or remote is not connected
heat
Machine is heating but is not yet up to operating
temperature
heat + ready
Machine is heating and has reached minimum operating
temperature. Fog output level may be reduced while
heating.
ready
Machine has finished heating and is at full operating
temperature
OFF+ON
meaning
no lights
Timer is disabled
both on
Timer is programmed but not enabled
“OFF” lit
Timer is running, currently in Off/Wait period
“ON” lit
Timer is running, currently in On/Run period
“ON” flashing
The timer “ON” time is currently being programmed
“ON” lit, “OFF”
flashing
The timer “OFF” time is currently being programmed
Optional accessories (Magnum 850 only)
Fog fluid types
The following types of Martin/Jem fog fluid are suitable for use in this machine.
Each produces a different effect as described below. Martin supplies high
quality fog fluids that are based on ultra-pure deionized water. Use only the
following genuine Martin/Jem fog fluids. No other fluid is suitable for use.
DANGER! The Magnum smoke machine can run safely only on the specific
smoke fluids it is designed for. Use ONLY the Martin/Jem smoke fluids
designated in this manual. NEVER use any other type of fluid, or toxic gas may
be produced. You will probably also cause damage to the system that is not
covered by the product warranty. Do not dilute smoke fluid with water or any
other liquid. Discard smoke fluid if it becomes contaminated.
Regular DJ Fluid (DJ mix)
Regular DJ fluid is an economical fluid that gives a good, medium density
smoke well-suited for atmospheric effects.
Pro Smoke Super (ZR mix)
Pro Smoke Super fluid is a high-quality, general purpose fluid that produces a
dense white airborne fog with medium dispersal time. Its medium to high index
of refraction permits both good atmospheric effects and denser “white-outs”.
Fog fluid types
17
Basic service
Before servicing the Magnum smoke machine, read and observe all the
precautions listed in “Safety information” on page 3. Any service not described in
this section must be carried out by a Martin service technician.
Cleaning
Excessive dust, smoke fluid, and dirt buildup will degrade performance and
cause overheating and damage to the machine that is not covered by the
product warranty. To maintain adequate cooling, dust must be cleaned from the
outer casing and air vents of the machine periodically.
Isolate the machine from power and allow to cool completely before cleaning.
The smoke output nozzle remains hot for up to 10 hours after use.
•
Remove dust from the air vents with a soft brush, cotton swab, vacuum,
or compressed air.
•
Clean smoke fluid residues from the fog output of the machine using a
damp cloth.
•
Clean the outer casing with a damp cloth only.
Fuse replacement
The main fuse for the Magnum 850 smoke machine is located on the electronics
board inside the unit. The fuse for the Magnum 650 is located in a tray on the
mains connector.
DANGER! Disconnect the power supply before removing any covers. Live parts
inside!
850: To replace the fuse, disconnect the power cord from the supply, unscrew
the screws holding the top cover of the unit and remove the cover. The
electronics board is located at the back of the unit near the remote control
sockets. Remove the fuse holder cover and pull out the fuse.
650: To replace the fuse, disconnect the power cord from the mains plug on the
rear panel. Using a screwdriver, pull out the small fuse compartment underneath
the plug. Lift out the fuse.
Remove the spent fuse and replace with one of exactly the same size and rating.
The fuse type is indicated below. Contact Martin Service if the fuse blows
repeatedly.
Magnum 850
120V = 10AT
230V = 5AT
Magnum 650
120V = 10AT
230V = 5AT
18
Basic service
Troubleshooting
Problem
Probable cause(s)
Suggested remedy
Machine not at operating
temperature
Wait 10 to 15 minutes
Machine not powered up
Ensure mains power switch
on and AC power is OK
Smoke output is weak
Machine requires priming
Prime machine (page 13)
Wet, greasy, non-uniform
smoke output, fluid drips or
spits from nozzles, or very
loud noise when firing
machine
Incompatible smoke fluid
Use only approved fluid!
Mains fuse blown
Replace fuse (page 18)
No power at AC cable inlet
Check power cable and
circuit breaker
Machine will not produce fog
when remote control Fog
button pressed
Machine appears dead
Troubleshooting
19
Specifications
Magnum 650
Magnum 850
P h ys i c a l
Length ................................................................. 293mm............................ 450mm
Width ................................................................... 216mm............................ 205mm
Height.................................................................. 170mm............................ 244mm
Dry weight .............................................................. 8.2Kg............................... 9.9Kg
Performance
Effect coverage .............................................. 160m3/min....................... 200m3/min
Operating time ...................................................... cycles.......................continuous
Warm up time ...............................................7.5 minutes.........................8 minutes
Safety device.................................................OTP device...................... DTP device
Control and programming
Control options ................................................... remote.......remote, timer remote
DMX channels ........................................................... n/a................................... n/a
F l u i d s ys t e m
Capacity ..................................................................1 litre................................1 litre
Fluid consumption ...........................................23ml/min..........................35ml/min
Compatible fluids ...................................................DJ,ZR...............................DJ,ZR
Connections
DMX............................................................................ n/a................................... n/a
Remote / machine link .................................... hardwired............................RJ45 x2
AC power ......................................................... IEC plug...........................IEC plug
Electrical
AC voltage ....................................120V / 230V, 50/60Hz......120V / 230V, 50/60Hz
Main fuse (120V US version) .................................. 10AT................................ 10AT
Main fuse (230V EU version) .................................... 5AT.................................. 5AT
Power usage (120V US version) .................730W (6.1A).....................790W (6.6A)
Power usage (230V EU version) ...............620W (2.66A).....................790W (3.4A)
The following specifications apply to both machines:
Thermal
Maximum ambient temperature (Ta max)............................................ 40°C (104°F)
Exterior surface temperature, steady state, at 20°C ambient .............. 40°C (104°F)
Approvals
European EMC:....................................... EN61000-6-3,EN61000-3-2,EN61000-3-3
European safety: .................................................................................. EN 60 335-1
Immunity: ............................................... EN61000-6-1, EN61000-4-2,EN61000-4-3
ETL approvals (cETLus)................................................ UL60335-1, CSA-E60335-1
20
Specifications
Included items
EU Model:
3m(9.8ft) IEC power cable 3x1.0mm2 with Schuko male connector
3m(9.8ft) IEC power cable 3x1.0mm2 with no male connector
US Model:
2m(6.5ft) US power cable 18AWG with US male connector(UL approved)
1 x fluid container (empty)
Accessories
Timer remote (Magnum 850 only) .....................................................P/N 92765032
Ducting system Magnum series ........................................................P/N 92625009
Ordering information
Martin Magnum 650 smoke machine 120V .......................................P/N 92228810
Martin Magnum 650 smoke machine 230V .......................................P/N 92228811
Martin Magnum 850 smoke machine 120V .......................................P/N 92229110
Martin Magnum 850 smoke machine 230V .......................................P/N 92229111
Martin Magnum 850 remote control ..................................................P/N 92765030
Specifications
21
Download PDF
Similar pages