CON1200RD - Rotary Hammer Drill.fm

ROTARY HAMMER DRILL
MODEL NO: CON1200RD
PART NO: 6479600
OPERATION & MAINTENANCE
INSTRUCTIONS
LS0117
INTRODUCTION
Thank you for purchasing this CLARKE Hammer Drill. The CON1200RD is
designed for general drilling/masonry drilling/chiselling/drill & hammer use in
light industrial applications.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
INVENTORY
1
Moulding plastic carrying case
7
Pot of Grease
2
Rotary Hammer Drill
8
8mm SDS+ masonry drill bit
3
Front Handle
9
10mm SDS+ masonry drill bit
4
13 mm Drill Chuck Adaptor
10
12mm SDS+ masonry drill bit
5
Chuck Key
11
2 x SDS+ plus masonry chisel bits
6
Dust Shield Cup
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY PRECAUTIONS
WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL
INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/
OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED
BELOW REFERS TO YOUR HAMMER DRILL.
WORK AREA
1. Keep work area clean and well lit. Cluttered and dark areas invite
accidents.
2. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges or refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
2. Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
3. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in personal injury.
2. Use safety equipment. Always wear eye protection. Safety equipment such
as dust mask, non-skid safety shoes, or hearing protection used for
appropriate conditions will reduce personal injuries.
3. Avoid accidental starting. Ensure the switch is in the off position before
connecting to the power supply.
4. Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
5. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
POWER TOOL USE AND CARE
1. Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate which it was designed.
2. Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the battery before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
4. Store idle tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Poorly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
7. Use the power tool and accessories in accordance with these instructions
and in the manner intended for the particular type of power tool, taking
into account the working conditions and the work to be performed. Use of
the power tool for operations different from intended could result in a
hazardous situation.
SERVICE
1. Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY SYMBOLS
Read instruction
manual before use
Wear dust mask
Class 2 Double
Insulated
Wear ear defenders
CE Mark
Wear safety glasses
Weee Directive
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste. It must be disposed of according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ELECTRICAL CONNECTIONS
WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS
SUPPLY.
Before switching the product on, make sure that the voltage of your electricity
supply is the same as that indicated on the rating plate. Connecting it to any
other power source may cause damage.
If it is necessary to change the fuse in the plug, the fuse cover must be refitted.
If the fuse cover becomes lost or damaged, the plug must not be used until a
suitable replacement is obtained.
If the plug has to be changed due to damage, a replacement should be
fitted, following the wiring instructions shown below. The old plug must be
disposed of as insertion into a mains socket could cause an electrical hazard.
WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE
COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL
BROWN = LIVE
If the colours of the wires in the power cable of this product do not correspond
with the markings on the terminals of your plug, proceed as follows.
• The wire which is
coloured Blue must be
connected to the
terminal which is
marked N or coloured
Black.
• The wire which is
coloured Brown must
be connected to the
terminal which is
marked L or coloured
Red.
Plug must be BS1363/A approved.
Always fit
a 13 Amp
fuse
Neutral
(Blue)
Live
(Brown)
Ensure that the outer sheath of
the cable is firmly held by the clamp
We strongly recommend that this machine is connected to the mains supply via
a Residual Current Device (RCD)
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs
yourself.
This symbol indicates that this is a Class II product, and does not require
an earth connection.
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
OVERVIEW
NO DESCRIPTION
NO DESCRIPTION
1
SDS+ Chuck
5
Rear Handle
2
Rotation Stop Switch
6
Hammer Action Selector
3
Grease Port Cover
7
Motor
4
Trigger
8
Front Handle
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
BEFORE USE
INSERTING A DRILL BIT / CHISEL
The chuck clamps SDS+ drill bits and chisels without the need for a chuck key.
1. Pull back the collar.
2. Insert the bit
3. Turn the bit in the chuck until it
latches.
4. Release the collar to lock in
place.
5. Check by pulling the bit to see if it
is locked in place.
IMPORTANT: Always clean the shaft
of the drill bit before inserting into the chuck.
IMPORTANT: Do not allow dust or debris inside the chuck as this will cause
problems in the future.
REMOVING A BIT
1. Slide the collar to the rear and pull the bit out of the chuck.
CAUTION: WHEN REMOVING A BIT FROM THE DRILL, REMEMBER THAT IT
MAY BE EXTREMELY HOT. EITHER ALLOW IT TO COOL DOWN FIRST OR USE
INDUSTRIAL GLOVES TO REMOVE THE BIT.
USING THE DRILL CHUCK ADAPTOR (DRILL MODE ONLY)
When drilling with non SDS+ drill bits, a
13mm chuck (supplied) can be
inserted into the SDS+ chuck as
shown.
IMPORTANT: DO NOT USE THE
CHUCK ADAPTER IN HAMMER
ACTION MODE.
8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
POSITIONING THE FRONT HANDLE
The front handle can be positioned
left, right or centre as required.
1. Loosen the handle by twisting it
clockwise (when viewed from
above).
2. Rotate the handle to the required
position.
3. Secure the handle by twisting it
anticlockwise (when viewed from
above).
SELECTING THE OPERATING MODE
Mode
Hammer Action selector
Rotation selector
Drill Only
Drill Only
ON
Hammer Drill
Hammer Assisted Drilling
ON
Hammer only (no rotation)
Hammer Assisted Drilling
OFF
HAMMER ACTION SELECTOR
1. With the drill not operating, set the
hammer action selector to the
required setting.
• Left - Hammer Assisted Drilling
• Right - Drill Only
IMPORTANT: When using the
“hammer action” you only need to
apply light pressure. Too much
pressure will place unnecessary load on the motor. Check the drill bits
regularly, re-sharpen or replace if required.
9
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ROTATION ON/OFF SELECTOR
Some jobs require the chuck to
remain stationary yet still have the
hammer effect, such as chiselling
concrete, plaster etc.
• Set the rotation selector to the
right for “no rotation”.
• Set the rotation selector to the
left for “normal rotation”.
10
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
USING THE DRILL
BEFORE STARTING WORK
1. Before drilling into walls and floors etc., check first that there are no hidden
electrical cables, gas or water pipes etc.
2. Check the mains voltage before plugging in and switching on.
3. Ensure the work area is as hazard free as possible.
STARTING WORK
1. Select and install the bit to be used. See page 8.
2. If required, adjust the support handle attachment for the most comfortable
position. See page 9.
• For safety, always use the hammer drill with the front handle attached.
3. Set the required operating mode. See page 9.
4. When drilling vertically overhead,
fit the rubber dust shield cup
shown onto the drill bit.
5. Position the tool against the
surface to be drilled and pull the
trigger switch.
• If using the hammer action do
not start the drill until the tool is
in contact with the work
surface.
STOPPING WORK
1. Release the trigger and wait until the bit has stopped before placing the
drill on any surface
11
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
DRILLING TIPS
• Always use sharp, good quality drill bits. The performance of your drill is
dependant on the quality of the bits used.
• After drilling material to the full depth, do not simply pull out the drill but
maintain chuck rotation to ease withdrawal.
• Reduce the pressure on the drill bit when it is about to break through. This
will prevent the drill from jamming.
• If drilling a large hole, first drill a pilot hole using a smaller drill bit.
• Always apply pressure to your drill bit in a straight line and, where
possible, at right angles to the workpiece.
• When drilling in metal, the materials being drilled can become hot. To
reduce overheating use a suitable cooling lubricant. No cooling
lubricant is necessary when drilling cast iron or brass as they should be
drilled dry.
• When drilling metal, the harder the metal the slower the drill speed.
Similarly, the bigger the drill bit the slower the speed.
• To prevent the drill bit from slipping when starting to drill a hole in metal,
use a centre punch to make an indentation at the start point.
• Always start drilling at a slow speed to prevent the drill from slipping out
of the pop mark or indent, gradually increasing speed until the optimum
cutting speed is achieved whilst maintaining a MODERATE pressure
ONLY. NEVER force the drill bit into the work. This will overheat the tip and
cause it to dull very quickly.
• When drilling in wood, clamp a piece of scrap wood to the underside of
the material to avoid splintering.
• Large holes should be drilled with wood augers, flat wood bits or hole
saws.
DRILL BITS
A Wide choice of SDS+ and standard drill bits are readily available for this drill.
Please contact your local stockist or visit the Clarke website at:
www.clarkeinternational.com
12
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
MAINTENANCE AND SERVICING
1. After use, remove the drill bit and tap the side of the chuck to remove any
dust or chippings etc.
2. Keep the handle clean and free from oil and grease.
3. Worn or damaged parts must be replaced by qualified personnel.
4. Clean the tool regularly, use a soft brush and or soft cleaning cloth. DO
NOT use any chemicals or harsh abrasives to clean the tool.
5. At the end of work, to prevent dust deposits you should use compressed air
(max.3 bar) to clean out the ventilation holes.
GEARBOX GREASE
Check gearbox occasionally and top up if necessary with a good quality high
melting point grease.
1. Remove the 4 hex bolts from the
grease cover.
2. Remove the cover.
3. Apply sufficient grease to cover
all visible moving parts.
• DO NOT overfill the gearbox.
4. Replace the cover and hex bolts
before using the drill again.
13
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SPECIFICATIONS
Operating Voltage and
Frequency
230V AC~ 50Hz -1phase
Rated Input Power
1200W
Chuck capacity/type
SDS+ Plus
13mm keyed chuck adapter
Rotational Speed
Drill Mode 860 rpm
Drill/Hammer Mode 820 rpm
Impact Rating
4050 (blows/min)
Maximum Drilling Capacity:
Wood - 42 mm,
Steel - 13 mm,
Concrete - 32 mm
Sound Pressure Level
96.4 dB LpA
Sound Power Level
107.4 dB LWA
Vibration
Rotary hammer - 19.327 m/s2
Chiselling hammer - 17.879 m/s2
Weight
4.7 kg
Dimensions (LxHxW)
410 x 275 x 105 mm
Duty Cycle classification
S1 Continuous
14
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
PARTS DIAGRAM
15
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
PARTS LIST
ID
DESCRIPTION
ID
DESCRIPTION
1
Rubber Cap
31
Cylinder Case
2
Circlip
32
Circlip
3
Chuck Grip
33
Bearing
4
Spring
34
Gearbox
5
Chuck Barrel
35
Small Gear
6
Screw
36
Washer
7
Washer
37
Bearing
8
Washer
38
Washer
9
Oil Seal
39
Gear
10 Washer
40
Fixing Plate
11 Circlip
41
Washer
12 Bearing
42
Ball
13 Ball
43
Plate
14 Flex
44
Spring
15 X-ring
45
Nut
16 O-ring
46
Bearing
17 Impact Hammer
47
Eccentric Shaft
18 Ball
48
Bearing
19 Cylinder
49
Washer
20 Flat Key
50
Washer
21 Spring
51
Washer
22 Drive Gear
52
Spring
23 Circlip
53
Flat Key
24 Hammer
54
Spindle
25 O-ring
55
Gear
26 Piston Pin
56
Needle Bearing
27 Piston
57
Impact Bolt Holder
28 Connecting Rod
58
Centre Cover
29 Needle Bearing
59
Middle Cover
30 O Ring
60
O-ring
16
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ID
DESCRIPTION
ID
61 Hammer Action Selector
DESCRIPTION
84
Screw
62 Screw
85
Spring
63 Retainer
86
Anti-vibration Board
64 Bearing
87
Screw
65 Rotor
88
Anti-vibration Cover
66 Screw
89
Right Side Of Handle
67 Stator
90
Trigger
68 Bearing
91
Capacitor
69 Motor Casing
92
Inductor
70 Screw
93
Power Cable
71 Brush
94
Cable Sheath
72 Brush Holder
95
Cable Board
73 Brush Cover
96
Left Hand Handle Sheath
74 Screw
97
Right Hand Handle Sheath
75 Upper Cover
98
Screw
76 Rotation Selector
99
Left Side Of Handle
77 Spring
100 Screw
78 Button
101 Nut
79 Washer
102 Socket Head
80 Washer 14
S1
Hoop
81 Screw
S2
Screw
82 O-ring
S3
Bracket
83 Cover
S4
Handle/grip
When ordering spare parts, please quote the reference TXCON1200RD01
onwards. e.g. Eccentric Shaft will be TXCON1200RD47.
17
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
DECLARATION OF CONFORMITY
18
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
19
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
Download PDF
Similar pages