User Manual - Element Electronics

E4SFC5017
50" UHD Digital LED TV
INSTRUCTION MANUAL
Please read all the instructions carefully before using this TV,
and keep the manual for future reference.
CONTENTS
Important Safety Instructions
2
Additional Safety Information
3
Preparations
What's Included
Front/Rear View
Rear View
Wall Mounting
Remote Control
4
4
5
5
6
7
Connecting External Devices
8
Customizing TV Settings
Turning On/Off Your TV
Initial Setup
Source
Channel Selection
Volume Adjustment
Streaming
Media
Viewing Photos
Listening To Music
Watching Videos
TV Settings
General
Picture Settings
Audio Settings
Network Settings
Channel Settings
Time Settings
Lock Settings
APP Settings
Support
Parental Control
9
9
9
11
11
11
12
13
13
14
14
15
16
17
18
19
19
20
21
22
22
23
Troubleshooting
25
FCC Notes
28
Specifications
28
OTT APP Service
29
1
IMPORTANT SAFETY INSTRUCTIONS
• Read these instructions – All the safety
and operating instructions should be read
before this product is operated.
• Keep these instructions – The safety
and operating instructions should be
retained for future reference.
• Heed all warnings – All warnings on
the appliance and in the operating
instructions should be adhered to.
• Follow all instructions – All operating
and use instructions should be followed.
• Do not use this apparatus near water
– The appliance should not be used near
water or moisture – for example, in a wet
basement or near a swimming pool, and
the like.
• Clean only with dry cloth.
• Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
• Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
• Do not defeat the safety purpose of
the polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding-type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.
• Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
• O n l y u s e a t t a c h m e n t s / a c c e s s o r i e s
specified by the manufacturer.
• Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
• Unplug this apparatus during lightning
storms or when unused for long periods
of time.
2
• Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as the power-supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally, or
has been dropped.
• Please keep the unit in a well-ventilated
environment.
WARNING: To reduce the risk of fire or electric
shock, do not expose this apparatus to rain
or moisture. The apparatus should not be
exposed to dripping or splashing. Objects
filled with liquids, such as vases should not be
placed on apparatus.
WARNING: The batteries shall not be exposed
to excessive heat such as sunshine, fire or the
like.
WA R N I N G : T h e m a i n p l u g i s u s e d a s
disconnect device, the disconnect device shall
remain readily operable.
WARNING: To reduce the risk of electric
shock, do not remove cover (or back) as there
are no user-serviceable parts inside. Refer
servicing to qualified personnel.
RISQUE DE CHOC ELECTRIQUE NE
PAS OUVRIR
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to
the presence of non-insulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance instructions in
the literature accompanying the appliance.
This equipment is a Class II or double
insulated electrical appliance. It
has been designed in such a way
that it does not require a safety connection to
electrical earth.
ADDITIONAL SAFETY INFORMATION
To ensure reliable and safe operation of this equipment, please read carefully all the
instructions in this user guide, especially the safety information below.
Electrical Safety
• The TV set should only be connected to a main power supply with voltage that
matches the label at the rear of the product.
• To prevent overload, do not share the same power supply socket with too many other
electronic components.
• Do not place any connecting wires where they may be stepped on or tripped over.
• Do not place heavy items on them, which may damage the leads.
• Hold the main plug, not the wires, when removing from a socket.
• During a thunderstorm, or when not using the television for extended period of time,
turn off the power switch on the back of the television.
• Do not allow water or moisture to enter the TV or power adapter. Do NOT use in wet,
moist areas, such as bathrooms, steamy kitchens or near swimming pools.
• Pull the plug out immediately, and seek professional help if the main plug or cable
is damaged, liquid is spilt onto the set, if accidentally exposed to water or moisture,
if anything accidentally penetrates the ventilation slots or if the set does not work
normally.
• Do not remove the safety covers. There are no user serviceable parts inside. Trying
to service the unit yourself is dangerous and may invalidate the product’s warranty.
Qualified personnel must only service this apparatus.
• To avoid battery leakage, remove exhausted batteries from the remote control, or
when not using for long period.
• Do not break open or throw exhausted batteries on a fire.
• Do not mix old and new batteries.
• Do not mix Alkaline,Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or
(Nickel Metal Hydride) batteries.
Physical Safety
• Do not block ventilation slots in the back cover. You may place the TV in a cabinet,
but ensure at least 5cm (2'') clearance all around.
• Do not tap or shake the TV screen, or you may damage the internal circuits. Take
good care of the remote control.
• To clean the TV use a soft dry cloth. Do not use solvents or petroleum based fluids.
• Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong, the wide blade, or the third prong is provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs.
• Unplug the apparatus during lightning storms or when unused for long periods.
• Refer all servicing to a qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled, or objects have fallen into the apparatus, has been
exposed to rain or moisture, does not operate normally, or has been dropped.
3
PREPARATIONS
What is Included?
1
2
3
4
5
6
7
8
9
0
MENU
SOURCE
OK
RETURN
EXIT
USB
VOL
CH
REPEAT
INFO
TV Set
FREEZE
ADD/ERASE
FAV
CH.LIS T
P.MODE
S.MODE
V-CHIP
CC
MTS
ASPECT
SLEEP
AUTO
HDMI
VGA
TV
Remote Control with Batteries
E4SFC5017
50" UHD Digital LED TV
INSTRUCTION MANUAL
QUICK START GUIDE
Please read all the instructions carefully before using this TV,
and keep the manual for future reference.
User Manual
4
Quick Start Guide
PREPARATIONS
Front/Rear View
LED
IR
•
Switch the TV between On / Standby mode.
• SOURCE
Press to select among different input signal sources.
• MENU
Display the OSD (on screen display) menu.
• CH
Press to select a channel.
• VOL +/Press to adjust the volume.
• LED
The LED light indicates when the TV is activated.
• IR
Infrared Receiver.
5
PREPARATIONS
2
900
Rear View
9
4
8
1
2
3
4
1. Optical Output
Connect a digital sound system to this jack.
2. USB Input
Connect to a USB storage device to play
photo files. (USB mode)
3. LAN
Network connection port.
4. HDMI Inputs
Connect to a High-Definition (HD) signal
input device.
5. VGA Input
Connect to a computer or other devices
with a VGA interface.
5
6
7
6. PC Audio Input
Connect to a computer audio output.
7. Antenna Input (75Ω VHF/UHF)
Connect to the antenna (75Ω VHF/UHF)
socket with the RF coaxial cable.
8. Headphone output
Connect to the Headphones.
9. COMPONENT/AV Input
Connect to AV devices with composite/
component (Y/Pb/Pr) video and audio output
sockets. COMPOSITE VIDEO and COMPONENT(Y/
PB/PR) share with AUDIO IN (L/R).
Wall Mounting
The TV is provided with mounting holes for a VESA approved wall mounting bracket (Not Supplied).
Remove the screws holding the base to the base bracket and lift the base away (do not remove the base
mounting brackets). Mount the VESA bracket using 4*M6*12 isometric threaded screws (Not Supplied).
WARNING
Never place a television set in an unstable location. A television set may fall, causing serious personal
injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such
as:
-Using cabinets or stands recommended by the manufacturer of the television set.
-Only using furniture that can safely support the television set.
-Ensuring the television set is not overhanging the edge of the supporting furniture.
-Not placing the television set on tall furniture(for example, cupboards or bookcases) without anchoring
both the furniture and the television set to a suitable support.
-Not placing the television set on cloth or other materials that may be located between the television set
and supporting furniture.
-Educating children about the dangers of climbing on furniture to reach the television set or its controls.
If your existing television set is being retained and relocated, the same considerations as above should
be applied.
Your new TV is heavy, please consult with professional wall mount installer to perform this installation.
6
PREPARATIONS
Remote Control
1.
:Switch the TV between On and
Standby mode.
2.
:Mute and restore TV sound.
3. 0~9:Select a program.(ATV/DTV mode)
4. —:Enter multiple program channel number
such as 2-1.
5.
:Return to the previous viewing channel.
6. APP:Press to select the desired APP.
7. MENU:Display the main menu.
8. SOURCE:Select among the different input
signal sources:TV/AV/COMPONENT/HDMI1/
HDMI2/HDMI3/VGA/USB.
:Allows you to navigate the on
9.
screen display menus and adjust the system
settings to your preference.
10. OK:Confirm the selection.
11. RETURN:Return to previous menu.
12. EXIT:Exit the on screen display menu.
13. USB:Access into the USB directly.
14. VOL+/-:Adjust the volume.
15. CH :Select the channel.
16. REPEAT:Press repeatedly to select the repeat
mode.
17. :Stop the playback.
18. :Skip to the beginning of the previous
chapter/track/photo.
19. :Skip to the beginning of the next chapter/
track/photo.
20. :Reverse playback rapidly.
21. :Advance playback rapidly.
22. FREEZE:Freeze the picture.
23. :Start playback or pause.
24. ADD/ERASE:Add or delete Favorite channels.
25. FAV:Display the favorite channel list.
26. INFO:Display the present screen information
such as the current channel and input source.
27. S.MODE:Select sound mode:standard/music/
movie/user.
28. P.MODE:Select picture mode:dynamic/movie/
user/standard.
29. CH.LIST:Display program list.
30. V-CHIP:Set up parental control.
31. ASPECT:Select the aspect ratio.
settings:standard/wide/wide zoom/zoom/Just Scan
(HDMI)/Dot by Dot(VGA).
32. CC:Closed Caption selection:ON/OFF/CC On
Mute.
33. MTS:Switch among different audio
channels:STEREO/MONO/SAP.
34. AUTO:Press to adjust the picture automatically
in VGA source.
35. SLEEP:Set the TV sleep timer: OFF/5/10.../180
/ 240 min.
36. TV:Press to turn to TV mode.
37. HDMI:Access into the HDMI directly.
38. VGA:Access into the VGA directly.
7
CONNECTING EXTERNAL DEVICES
8
CUSTOMIZING TV SETTINGS
Turning On/Off Your TV
• Connect the power cord to the power socket after you have completed all the
physical connections. At this stage, the TV will enter Standby Mode and the red
LED indicator will illuminate.
• In Standby Mode, press the
button on the main unit or on the remote control to
turn the TV on. The red LED indicator will turn blue.
The POWER button on the main unit or on the remote control can only
switch the TV into standby. To completely turn off the TV, please disconnect
the power cord from the power socket.
Initial Setup
• The first time you turn the TV on, it will go into
the Setup Wizard. Press the Arrow buttons
to highlight and select your desired mode and
press OK to confirm. 9
CUSTOMIZING TV SETTINGS
Initial Setup
Home Mode :The picture mode will be Standard if you
select this mode.
Retail Mode:Select Dynamic Mode if you would like
your picture to be brighter. At times this mode may use
more energy to operate the Volume/Sound Mode and
Picture Mode.
The SLEEP-MODE power consumption should be less
than 0.5W.
• Follow the next screens. Use the arrow keys on
the remote control and then press OK button to
customize your TV channel configuration.
• After the channel scan, your TV channels will be set
up.
Use the UP and DOWN
arrows on your remote
control or TV keypad to
select the channel scan type.
5
FOUND
QUIT
RETURN TO SCAN CHANNELS PROGRAM
7
CONNECT A GAME, BLU-RAY, DVD OR OTHER PLAYERS
• If channels cannot be found, this frame
will be displayed automatically.
10
CUSTOMIZING TV SETTINGS
Source
SOURCE
TV
AV
COMPONENT
• Press SOURCE on the remote control or on
the main unit to display the source menu, then
use the Arrow buttons to cycle among the
different input sources: TV/AV/COMPONENT/
HDMI1/HDMI2/HDMI3/VGA/USB, then use the
Arrow buttons to highlight the desired source
and press OK to confirm.
HDMI 1
HDMI 2
HDMI 3
VGA
USB
Channel Selection
• Press the CH /CH buttons on the main unit or on the remote control repeatedly
to select the channel.
• Press the 0-9 buttons on the remote control to select the channel directly.
Press "4", and then press OK button to select channel 4.
Press "4" and "5", and then press OK button to select channel 45.
Press "1", "2" and "3", and then press OK button to select channel 123.
Volume Adjustment
• Press the VOL+/- buttons on the main unit or on the remote control to adjust the
volume.
• If you wish to switch the sound off, press the MUTE button again or the VOL+
button to resume the sound.
11
CUSTOMIZING TV SETTINGS
Streaming
STREAMING
MY MEDIA
TV SETTINGS
NETWORK
• Press MENU button on the main unit or on the remote to display the main
interface. Then use the Arrow buttons to select STREAMING and press OK to
enter. Use the Arrow buttons to select the desired APP and press OK button to
view. Or press the hotkey on the remote control to enter the desired APP directly.
For full listing of available Apps, please visit elementelectronics.com.
NETFLIX
YouTube
VUDU
Pandora
Toon goggles
AccuWeather
12
Enjoys TV shows & movies streamed instantly over the
Internet.
YouTube your way on the best screen in your house.
Discover, watch and collect the latest movies and
TV shows in high quality 1080p. Free to sign up. No
subscriptions, late fees or commitments.
Free personalized radio that offers effortless and
endless music enjoyment and discovery. Just start with
the name of one of your favorite artists, songs, genres
or composers and Pandora will do the rest. It’s easy to
create personalized stations that play only music you’ll
love.
A subscription video on-demand platform that offers
animated, fun and educational cartoons, engaging
games and songs from all over the world and in many
different languages to children.
Displays the current weather conditions and the
temperature anywhere in the world in centigrade or
Fahrenheit.
CUSTOMIZING TV SETTINGS
Media
STREAMING
MY MEDIA
My Media
Display photos, music & video from a USB drive.
Press ‘OK’ on your Remote or change Source to USB.
TV SETTINGS
NETWORK
PHOTOS
MUSIC
VIDEO
• Press MENU button to display the main interface, then use the Arrow buttons to
highlight MY MEDIA and press OK to confirm. Select among Photos, Music and
Video to view what you like.
Note: Portable drives should be inserted before entering MY MEDIA menu.
Viewing Photos
• Use the Arrow buttons to highlight the PHOTOS option and press OK, then it will jump
to confirm the inserted drive, press OK to enter. After entering PHOTOS, use the Arrow
buttons to select the picture file and press OK to enter.
• After entering the picture file, use the Arrow buttons to select the desired picture,
to display. When the picture is playing, the picture Function Bar will be
then press the
displayed. Use the Arrow buttons to select the desired function available on the bar.
13
CUSTOMIZING TV SETTINGS
Listening To Music
• Use the Arrow buttons to highlight the MUSIC option and press OK, then it will jump
to confirm the inserted drive, press OK to enter. After entering MUSIC, use the Arrow
buttons to select the audio file and press OK to enter.
• After entering the audio file, use the Arrow buttons to select the desired music, then press
the
to display. When the picture is playing, the music Function Bar will be displayed. Use
the Arrow buttons to select the desired function available on the bar.
Watching Videos
• Use the Arrow buttons to highlight the VIDEOS option and press OK, then it will jump
to confirm the inserted drive, press OK to enter. After entering VIDEOS, use the Arrow
buttons to select the video file and press OK to enter.
• After entering the video file, use the Arrow buttons to select the desired music, then press
the
to display. When the picture is playing, the music Function Bar will be displayed. Use
the Arrow buttons to select the desired function available on the bar.
14
CUSTOMIZING TV SETTINGS
TV Settings
STREAMING
MY MEDIA
GENERAL
PICTURE
AUDIO
NETWORK
CHANNEL
TIME
TV SETTINGS
NETWORK
• Press the MENU button on the main unit or on the remote control to display the
main interface. Then use the Arrow buttons to highlight TV Settings and press
OK to enter. Then use the Arrow buttons to cycle among the following options
and select the desired one to enter.
15
CUSTOMIZING TV SETTINGS
General
• Press MENU to display the main interface, then
use the Arrow buttons to highlight TV Settings
and press OK to confirm. Use the Arrow buttons
to cycle among different options and select
General to enter and adjust each option setting.
MENU LANGUAGE
TRANSPARENCY
ZOOM MODE
VGA SETTINGS
CLOSED CAPTION
DLC
OTHER SETTINGS
RESTORE DEFAULT
16
Select the menu language among
English, Français or Español. The
default on-screen menu language is
English.
Select to turn On/Off transparency
function.
Select zoom mode:
Wide/Wide Zoom/Zoom/Auto/
Standard/Just Scan(at HDMI mode)/
Dot by Dot(at VGA mode).
Note: With a different input source,
the zoom mode options may differ.
Adjust advanced option’s setting:
H-POS, V-POS, Clock, Phase or
Auto. (only available in VGA mode)
CC mode
On/Off/CC on Mute.
CC1, CC2, CC3,
Basic
CC4, Text1, Text2,
Selection
Text3, Text4.
Advanced
Service1/Service2.../
Selection
Service6.
Mode, Font Style,
Font Size, Font Edge
Style, Font Edge
Option
Color, FG_ Color,
BG_ Color, FG_
Opacity, BG_Opacity.
Select to turn the dynamic
luminance control On/Off.
HDMI EDID: Select the HDMI
version: HDMI 2.0/HDMI 1.4.
Inlink: Set the options: Inlink
Control, Device Power Off, TV
Power On, Audio Receive, Inlink
Device List, Root Menu.
Restore the TV to factory default
settings.
CUSTOMIZING TV SETTINGS
Picture Settings
• Press MENU to display the main interface, then
use the Arrow buttons to highlight TV Settings
and press OK to confirm. Use the Arrow buttons
to cycle among different options and select
Picture to enter and adjust each option setting.
PICTURE MODE
BLUE SCREEN
BRIGHTNESS
CONTRAST
COLOR
SHARPNESS
TINT
COLOR
TEMPERATURE
ADVANCED
OPTION
MEMC
Cycle among picture modes:
Dynamic/Standard/Movie/User.
Alternative: Press P.MODE button on
remote control to set the picture mode
directly.
Allow the blue background to turn
On/Off during weak or no signal
conditions.
Increase or decrease the amount of
white in the picture.
Adjust the difference between light
and dark levels in the pictures.
Control the color intensity.
Adjust crispness level in edges
between light and dark areas of the
picture.
Adjust the balance between red and
green levels.
Cycle among color temperatures:
Normal/Warm/Cool.
Set the following options:
Noise Reduction: Reduce the noise
level of the connected device: Off/
Weak/Middle/Strong.
White Balance: To set the different
options of white balance.
Color Management: set different color
options
Backlight: To set the value of
backlight.
Gamma: To set Gamma value:
2.0/2.2/2.4.
Reset: To reset the advanced option.
Cycle among Motion Estimate and
Motion Compensation modes:
Medium/High/Off/Low.
17
CUSTOMIZING TV SETTINGS
Audio Settings
• Press MENU to display the main interface, then
use the Arrow buttons to highlight TV Settings
and press OK to confirm. Use the Arrow buttons
to cycle among different options and select Audio
to enter and adjust each option setting.
SOUND MODE
BASS
TREBLE
BALANCE
DIGITAL AUDIO
OUTPUT
SURROUND
SOUND
AUTO VOLUME
AUDIO
LANGUAGE
18
Allow the selection of an audioenhancement technique: Standard/
Music/Movie/User.
Control the relative intensity of lowerpitched sounds.
Control the relative intensity of higherpitched sounds.
Adjust the relative volume of the
speaker in a multiple speaker system.
Select the digital audio output mode
between PCM/RAW.
Turn On/Off to provide an enhanced
listening experience.
Turn On/Off to automatically control
volume levels.
Select audio language among: English,
French, Spanish.
CUSTOMIZING TV SETTINGS
Network Settings
• Press MENU to display the main interface, then
use the Arrow buttons to highlight TV Settings.
Use the Arrow buttons to cycle among different
options and select Network then press OK to
enter and adjust each option setting.
• The first time when connecting the network and
make connection successfully, Network Updated
menu will pop up, and confirm Next to enter
Enable Interactive TV menu. Then selecting
Enable option and press OK button to interactive
your TV and make some settings.
NETWORK
TYPE
MY NETWORK
IP ADDRESS
Select Lan and Wireless network, then
connect the TV to the wired network or
search the wireless network through
searching available Wifi.
Display the current network which you
connect to.
Display the current IP information.
Channel Settings
• Press MENU to display the main interface, then
use the Arrow buttons to highlight TV Settings.
Use the Arrow buttons to cycle among different
options and select Channel to enter and adjust
each option setting.
AIR/CABLE
AUTO SCAN
FAVORITE
SHOW/HIDE
CHANNEL
NUMBER
CHANNEL
LABEL
SIGNAL
INFORMATION
Select antenna between Air and
Cable.
Select the Auto Scan feature to scan
your available Air and cable channels.
Set the selected channel as a favorite
channel.
Show/Hide the selected channel.
Display the current channel number.
Display the current channel label.
Display the information of current
signal.
19
CUSTOMIZING TV SETTINGS
Time Settings
• Press MENU to display the main interface, then
use the Arrow buttons to highlight TV Settings
and press OK to confirm. Use the Arrow buttons
to cycle among different options and select Time
to enter and adjust each option setting.
SLEEP TIMER
OSD TIMER
TIME ZONE
DAYLIGHT
SAVING TIME
20
Select a period of time after which the TV
automatically switches to standby mode:
Off/5/10/…/180/240 min.
Alternative: You may press the SLEEP
button repeatedly to select the number of
minutes directly.
Set the OSD timer:
Off/15s/30s/60s/120s/240s.
Select a Time Zone:
Pacific/Alaska/Hawaii/Newfoundland/
Atlantic/Eastern/Central/Mountain.
Select to turn daylight saving time On/Off.
CUSTOMIZING TV SETTINGS
Lock Settings
• Press MENU to display the main interface, then
use the Arrow buttons to highlight TV Settings.
Use the Arrow buttons to cycle among different
options and select Lock to enter and adjust each
option setting.
Note: the default password is “0000”.
Use 0-9 buttons to input the old
password and then input the new 4-digit
password. Re-enter new password for
confirmation.
Select to turn On/Off system lock. The
following options (USA, Canada, RRT
SYSTEM LOCK Setting and Reset RRT) will only be
accessible when you turn the system
lock on.
TV RATING: Press OK
TV
button to lock or unlock TV
rating.
USA
Select MPAA rating : N/A,G,
MPAA
PG, PG-13, R, NC-17,or X.
Select MPAA rating for
Canada
English-speaking Canada
English
: E, C, C8+, G, PG, 14+,
18+.
CANADA
Select MPAA rating for
Canada
Quebec Canada : E, G, 8
French
ans+, 13 ans+, 16 ans+, 18
ans+.
RRT SETTING
Set Rating Region Table.
RESET RRT
Select to reset the RRT setting.
CLEAR LOCK
Clear all lock settings.
CHANGE
PASSWORD
21
CUSTOMIZING TV SETTINGS
APP Settings
• Press MENU to display the main interface,
then use Arrows to highlight TV Settings. Use
Arrows to cycle among different options and
select App Settings to enter and adjust each
option setting.
DEACTIVATE
APP
DEACTIVATE
APP
INTERACTIVE
TV SETTINGS
ESN
Deactivate Netflix and clear the account
information.
Deactivate Vudu and clear the account
information.
To enter the Muse and enjoy the
different programs and shows in the
Samba TV .
Electronic Serial Number.
Support
• Press MENU to display the main interface, then use the Arrow buttons to highlight TV
Settings and press OK to confirm. Use the Arrow buttons to cycle among different options
and select Support to enter and view the electronic user manual.
22
CUSTOMIZING TV SETTINGS
Parental Control
Press the MENU button on the main unit or on the remote control and then press the
buttons to select LOCK menu. Use the 0-9 buttons to input 4-digit password to enter
the LOCK menu. If used, this option feature can "block'' undesirable programming from
appearing on the TV. Parental Control offers the user a wide variety of options and settings
that restrict or "block'' the programming that can appear on the TV. Parental Control allows
the user the capability of defining which program rating they consider acceptable to the
younger more sensitive viewer. It can be preset and turned either on or off by the user
who specifies the secret 4-number code, the password. The number of hours blocked are
specified. General audiences and children blocks should be both programmed into the
TV's memory. Viewer ratings are specified for both TV and the motion picture Industry; both
rating systems should be used, for complete coverage. The ratings are based on the ages
of children.
Overview
To ensure complete coverage for all TV programs, (movies and regular TV shows) choose
a rating for MPAA, from the selections below,as well as ratings from the TV Parental
Guidelines Rating Systems below, using the Age Block option for General Audiences, and
for children. In addition to those, you may wish to add additional restrictions from the content
block menu, and submenus examples below.
Things to Consider before Setting up Parental Control
Determine which rating you consider acceptable to the viewer. (For example,if you choose
TV-PG, more restrictive ratings will be automatically blocked; the viewer will not be able to
see: TV-PG,TV-14,or TV-MA rated programming.) Do you want to block the auxiliary video
source entirely? (Blocks the signal sent by the equipment, such as VCR, connected to the
TV Audio/VIdeo Input Jacks) Or leave unblocked, then choose allowable ratings. Block
program "Content" based on individual parameters such as: Strong Dialog, Bad Language,
Sex Scenes,Violence Scenes, or Fantasy. Violent Scenes; in Content Blk option. Select a
secret password, in the Set Password option, using the numbers keys on the remote control.
Do not forget the password, it is the only way you can access the Parental Control menu
and change rating selections, or turn Parental Control off.Do you want the Parental Control
to be active at all times? If not, you can turn it on or off with the Lock On/Off option.
• You can set different Parental Control viewing restrictions for general audiences and for
children, both can be active at the same time.
• Simply specifying one content block such as Sex Scenes, will not automatically restrict
the programming that appears from the video sources.
• Even If you choose to leave the AUX Inputs unblocked, the ratings you specify will
automatically restrict the programming that appears from the video sources.
• You can not disable Parental Control by disconnecting the TV from power. Block hours will
be automatically reset to the original block time setting specified if power is disconnected.
23
CUSTOMIZING TV SETTINGS
Motion Picture Association of America (MPAA) Rating System
Grade
General Audiences
Parental Guidance
Suggested
G
PG
PG-13
Parents Strongly
Cautioned
R
Restricted
NC-17
X
No Rating
No children under
age 17
Hard Core Films
No Rating
Meaning
Content not offensive to most viewers.
Content is such that parents may not want
their children to view the program.
Program is inappropriate for pre-teens, with a
greater degree of offensive material suggested
than a PG rated program.
Not for children under 17, strong element of
sex and/or violence.
Not for children under 17 under any
circumstances. Strong sexual content.
Same as NC-17 rating.
MPAA Not Rated
TV Parental Guideline Rating System
TV-Y
TV-Y7
Grade
All Children
Directed to Older
Children
TV-G
General Audience
TV-PG
Parental Guidance
Suggested
TV-14
Parents Strongly
Cautioned
TV-MA
Mature Audience
Only
Meaning
Content not offensive to most viewers.
Considered suitable for children over 7, may
contain fantasy violence scenes.
Considered suitable for all audience; children
may watch unattended.
Suggested unsuitable for younger children,
may contain suggestive language, bad
language, sex and violence scenes.
unsuitable for children under 14, may contain
strong language, bad language, sex and
violence scenes.
Adults only, may contain strong language, bad
language, sex and violence scenes.
Canadian Rating:
• Canadian English is used throughout all English-speaking Canada (C, C8+,G, PG,14+, 18+).
• Canadian French is used in Quebec (G,8 ans+, 13 ans+,16 ans+, 18 ans+).
The V-Chip will automatically block certain categories that are "more
restrictive".If you block TV-Y category,then TV-Y7 will be automatically
blocked. Similarly,if you block TV-G category, then allthe categories in the
"young adult" will be blocked (TV-G, TV-PG,TV-14,and TV-MA).
24
TROUBLESHOOTING
If your TV does not operate normally or cannot be turned on, please check
the following troubleshooting questions. Remember also to check any other
connected electronic device, such as DVD or blu-ray player to pinpoint the
problem. If the TV still fails to operate normally, please contact technical support
(Refer to Warraty page).
SYMPTOM
POSSIBLE CAUSE
Dead. No LED lit
No power to the TV.
Dead. No LED lit red
Set in standby mode.
Blue screen
No signal.
Incorrect
source selected.
Noisy, snowy, ghosting
picture (TV)
Poor antenna signal.
No sound
Sound "Mute".
Volume set too low.
External leads
not connected "if used".
PASSWORD
Lost password
REMEDY
• Check all connections to the
TV's AC socket.
• Press either the Power button
or the Standby button on the
remote control.
• Press the SOURCE button to
select the correct source.
• If using an indoor antenna, try
adjusting the antenna position.
Check antenna connections.
• Turn sound "Mute" off.
• Check volume settings.
• Check that all external leads
are connected properly.
Select the SET Password setting in the LOCK menu, then
enter the following master password “8899”. The master
password clears your previous password and allows you to
enter a new password.
25
TROUBLESHOOTING
Before contacting the service technician, perform the following simple checks. If
any problem still persists, unplug the LED TV and call for assistance.
PROBLEM
POSSIBLE SOLUTIONS
• Check that the main plug has been connected to a
wall outlet.
• Check that you have pressed the POWER on the
No sound and picture
front of the TV set.
• Check the picture contrast and the brightness
setting.
• Set in standby mode. Press either the Power button
Red LED indicator lights
or the Standby button on the remote control.
• Check the volume.
• Sound muted? Press the MUTE button.
Normal picture but no sound • Try another channel, the problem may be with the
broadcast.
• Are the audio cables installed properly?
• Check to see if there are any objects between the
TV and remote control causing obstruction.
The remote control does not
• Are batteries installed with correct polarity (+/-)?
work
• Correct remote operating mode set: TV, VCR, etc?
• Install new batteries.
• Is the sleep timer set?
• Check the power connection, power may be
Power suddenly turns off
interrupted.
• No broadcast on the station tuned.
• This is normal, the image is muted during the product
Picture appears slowly after
start up process. Please contact a service provider if
switching on
the picture has not appeared after 5 minutes.
• Adjust the color in Menu option.
• Keep a sufficient distance between the product and
the VCR.
• Try another channel, the problem may be with the
Poor color or picture
broadcast.
• Are the VIDEO cables installed properly?
• Activate any function to restore the brightness of the
picture.
Horizontal/vertical bars or • Check for local interference, such as an electrical
picture shaking
appliance or power tool.
Blue screen
• Press the SOURCE button to select correct source.
• Station or cable experiencing problems. Tune to
another station.
Poor reception on
• Station signal is weak, reorient antenna for better
some channels
reception.
• Check for sources of possible interference.
• Check the antenna (change the direction of the
Lines or streaks in pictures
antenna).
No output from one of the
• Adjust balance in the Menu option.
speakers
26
TROUBLESHOOTING
Note: When there is a problem in VGA mode ( only when VGA mode is applied).
PROBLEM
The signal is out of range
Ve r t i c a l b a r o r s t r i p o n t h e
background, horizontal noise
and incorrect position
Screen color is unstable or is a
single color
POSSIBLE SOLUTIONS
• Adjust resolution, horizontal or vertical
frequency.
• Check whether the signal cable is connected or
loose.
• Check the input source.
• Set the auto configure or adjust clock, phase, or
H/V position.
• Check the signal cable.
• Reinstall the PC video card.
Maintenance
Early malfunction can be prevented. Careful and regular cleaning can extend
the amount of time you will have with your new TV. Be sure to turn the power off
and unplug the power cord before you begin any cleaning.
Do not use your TV in areas that are too hot or too cold, because the cabinet
may warp or the screen may malfunction. Your TV works best in temperatures
that are comfortable to you.
Storage temperatures are 32° to 122°F(0° to 50°C).
Working temperatures are 32° to 95°F(0° to 35°C).
Do not place your TV in direct sunlight or near a heat source.
-minimum 5cm distances around the apparatus for sufficient ventilation;
-the ventilation should not be impeded by covering the ventilation openings with
items, such as newspapers, table-cloths, curtains, etc.;
-no naked flame sources, such as lighted candles, should be placed on the
apparatus;
-attention should be drawn to the environmental aspects of battery disposal.
Clean the screen
A great tip to dust off your screen: wet a soft cloth in a mixture of lukewarm
water and a little fabric softener or dish washing detergent. Wring the cloth until
it’s almost dry, and then use to wipe the screen.
Make sure the excess water is off the screen, then let air-dry before you turn on
the TV.
Cleaning the cabinet
To remove dirt or dust, wipe the cabinet with a soft, dry, line-free cloth. Please
be sure not to use a wet cloth.
27
FCC NOTES
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
For customer support: 1-888-338-5666
Please send all correspondence to:
Element TV Company, LP. Customer Service
15930 Valley Blvd., City of Industry, CA 91744
customerservice@elementelectronics.com
SPECIFICATIONS
Panel Size
Display Type
Panel Technology
Display Resolution
Panel Resolution
Aspect Ratio
Contrast Ratio-Panel
Brightness (Centre Typ.) Cd/M²
Response Time (G To G)
Lamp Life (Typ. Hours)
Horizontal Viewing Angle (At CR>10)
Vertical Viewing Angle (At CR>10)
TV System
Channel Range
49.5 inches diagonally
LED
TFT
3840 x 2160
3840 x 2160
16:9
3200~4000:1
180
8 ms
30,000 hours
178
178
ATSC/NTSC
VHF/UHF
Design and specifications are subjects to change without prior notice.
28
OTT APP SERVICE
OTT APP SERVICE
If you want to know about these APP information or get more service. Please refer to following
content.
• Netflix
You can call the following telephone for more help: 866-579-7172
If your matter is regarding customer service, please refer to https://contactus.netflix.com/help for
alternative contact information.
• YouTube
You can browse the following website for more help:
https://productforums.google.com/forum/#!categories/youtube/smart-tvs
• VUDU
You can call the following telephone for more help: 888-554-8838
• TG
You can call the following telephone for more help: 888-874-5411
• Pandora
You can send E-mail to Pandora for more help: pandora-support@pandora.com
• AccuWeather
You can send E-mail to AccuWeather for more help: CustomerService@AccuWeather.com
29
This product contains electrical or electronic materials. The presence of these materials may, if
not disposed of properly, have potential adverse effects on the environment and human health.
Presence of this label on the product means it should not be disposed of as unsorted waste
and must be collected separately. As a consumer, you are responsible for ensuring that this
product is disposed of properly.
P/NO.:002-BDF-ELEM
Download PDF
Similar pages