Delfield 6125XLR-S Installation manual

SHELLEYBASIC BY DELFIELD
Service, Installation and Care Manual
Please read this manual completely before attempting to install or operate this equipment! Notify
carrier of damage! Inspect all components immediately. See page 2.
N
CAUTIO
ION
T
A
M
R
O
T INF
N
A
T
R
O
USE
IMP
E
R
O
F
E
ONS!
I
T
C
READ B
U
R
NST
I
E
S
E
H
VE T
A
S
E
S
A
PLE
EFFECTIVE FEBRUARY 2004
Shelleybasic by Delfield Service & Installation Manual
CONTENTS
RECEIVING AND INSPECTING UNIT.................................. 2
SPECIFICATIONS ............................................................. 3-4
INSTALLATION...................................................................... 5
OPERATION....................................................................... 6-7
MAINTENANCE .................................................................... 8
WIRING DIAGRAM .......................................................... 9-12
REPLACEMENT PARTS LIST........................................ 13-16
STANDARD WARRANTIES............................................ 18-19
AUTHORIZED PARTS DEPOTS ......................................... 20
SERIAL NUMBER INFORMATION
The serial number on self-contained refrigerated units is on the
electrical specifications tag located near the condensing unit.
On hot food pans and hot/cold combination pans, the serial
number tag is located on the back of the control raceway or
remote panel.
The serial number tag also lists the refrigerant used and the
amount of charge.
Always have the serial number of your unit available when
calling for parts or service. A complete list of authorized
Delfield parts depots is shown on the back cover of this
manual.
©2004 The Delfield Company. All rights reserved. Reproduction without written
permission is prohibited. Delfield is a registered trademark of The Delfield
Company.
RECEIVING AND INSPECTING THE EQUIPMENT
Even though most equipment is shipped crated, care should
be taken during unloading so the equipment is not damaged
while being moved into the building.
1.
2.
3.
4.
5.
2
Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
If damaged, open and inspect the contents with the
carrier.
In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally as
well as in written form.
Request an inspection by the shipping company of the
damaged equipment. This should be done within 10 days
from receipt of the equipment.
Check the lower portion of the unit to be sure legs or
casters are not bent.
6.
7.
8.
Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines
are secure and base is still intact.
Freight carriers can supply the necessary damage forms
upon request.
Retain all crating material until an inspection has been
made or waived.
Uncrating the Equipment
First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required. If the unit is on legs remove the top of the crate
as well and lift the unit off the skid. If the unit is on casters it
can be "rolled" off the skid.
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Shelleybasic by Delfield Service & Installation Manual
SPECIFICATIONS
Shelleybasic by Delfield Model Numbers
Model #
Description
L
D
Shelleybasic by Delfield Heated Counters
SE-H2
2 food wells
39”
29”
SE-H3
3 food wells
50”
29”
SE-H4
4 food wells
64”
29”
SE-H5
5 food wells
78”
29”
SE-H6
6 food wells
92”
29”
H
Plug
Amp
Ship Wt
Frt Class
36”
36”
36”
36”
36”
14-20P
14-20P
14-30P
14-50P
14-50P
11
16
22
28
32
215
265
320
410
500
100
100
100
100
100
Amp
H.P.
Ship Wt
Ref Chrg.
4
4
7
7
7
1/5
1/5
1/4
1/4
1/4
340
415
490
565
640
8 oz.
8 oz.
16 oz.
16 oz.
16 oz.
Model #
12 X 20 Pans Held
L
D
H
Plug
Shelleybasic by Delfield Refrigerated Cold Pan Serving Counters
SE-C2
2
39”
29” 36”
5-15P
SE-C3
3
50”
29” 36”
5-15P
SE-C4
4
64”
29” 36”
5-15P
SE-C5
5
78”
29” 36”
5-15P
SE-C6
6
92”
29” 36”
5-15P
Model #
12 X 20 Pans Held
L
D
H
Plug
Amp
Shelleybasic by Delfield Hot / Cold Self-Contained Combination Counters
SE-HC2
2
39”
29” 36”
5-30P
17
SE-HC3
3
50”
29” 36”
14-30P
17
SE-HC4
4
64”
29” 36”
14-30P
22
SE-HC5
5
78”
29” 36”
14-50P
28
SE-HC6
6
92”
29” 36”
14-50P
33
Model #
12 X 20 Pans Held
L
D
H
Shelleybasic by Delfield Ice Cooled Serving Counters
SE-I2
2
39”
29” 36”
SE-I3
3
50”
29” 36”
SE-I4
4
64”
29” 36”
SE-I5
5
78”
29” 36”
SE-I6
6
92”
29” 36”
204
379
569
758
948
708
812
889
1373
1469
200
245
280
330
380
100
100
100
100
100
H
Plug
Amp
H.P.
Ship Wt
Ref Chrg.
36”
36”
36”
36”
36”
5-15P
5-15P
5-15P
5-15P
5-15P
7.5
7.5
7.5
7.5
8
1/4
1/4
1/4
1/4
1/3
370
445
530
600
670
24 oz.
24 oz.
24 oz.
24 oz.
24 oz.
D
H
Ship Wt
Frt Class
29”
29”
29”
29”
29”
36”
36”
36”
36”
36”
150
170
200
230
280
100
100
100
100
100
H
Ship Wt
Frt Class
36”
170
100
D
H
Ship Wt
Frt Class
29”
36”
140
100
Amp
H. P.
Ship Wt
Ref Chrg.
5
5
1/4
1/4
460
505
9 oz.
9 oz.
Model #
Cabinet Capacity
L
D
H
Plug
Shelleybasic by Delfield Ice Cream Counters - 0 degree only
SE-ICE1
210 cups
39”
29” 36”
5-15P
SE-ICE2
420 cups
50”
29” 36”
5-15P
Model #
L
Shelleybasic by Delfield Corner Units
SE-28
29”
SE-38
39”
1/5
1/5
1/4
1/4
1/4
Sys. Cap.
Frt Class
Model #
Description
L
D
Shelleybasic by Delfield Cashier’s Stand
SE-CS
Cashier’s Stand
29”
29”
Model #
Description
L
Shelleybasic by Delfield Tray Stand
SE-TS
Tray Stand
39”
BTU Load
204
379
569
758
948
Ship Wt
Model #
Description
L
D
Shelleybasic by Delfield Frost Top Counters
SE-F2
Frost Top
39”
29”
SE-F3
Frost Top
50”
29”
SE-F4
Frost Top
64”
29”
SE-F5
Frost Top
78”
29”
SE-F6
Frost Top
92”
29”
Model #
Description
L
Shelleybasic by Delfield Utility Counters
SE-U2
Utility, Flat Counter
39”
SE-U3
Utility, Flat Counter
50”
SE-U4
Utility, Flat Counter
64”
SE-U5
Utility, Flat Counter
78”
SE-U6
Utility, Flat Counter
92”
H.P.
BTU Load
D
H
Ship Wt
Frt Class
29”
29”
36”
36”
110
160
100
100
Sys. Cap.
708
812
889
1373
1469
Ref Chrg.
5.5 oz.
5.5 oz.
8 oz.
8 oz.
12 oz.
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
3
Shelleybasic by Delfield Service & Installation Manual
SPECIFICATIONS continued
Shelleybasic by Delfield Model Numbers
Model #
Description
L
D
Shelleybasic by Delfield Heated Counters
SES-H2
2 food wells
39”
29”
SES-H3
3 food wells
50”
29”
SES-H4
4 food wells
64”
29”
SES-H5
5 food wells
78”
29”
SES-H6
6 food wells
92”
29”
H
Plug
Amp
Ship Wt
Frt Class
30”
30”
30”
30”
30”
14-20P
14-20P
14-30P
14-50P
14-50P
11
16
22
28
32
215
265
320
410
500
100
100
100
100
100
Amp
H.P.
Ship Wt
Ref Chrg.
4
4
7
7
7
1/5
1/5
1/4
1/4
1/4
340
415
490
565
640
8 oz.
8 oz.
16 oz.
16 oz.
16 oz.
Model #
12 X 20 Pans Held
L
D
H
Plug
Shelleybasic by Delfield Refrigerated Cold Pan Serving Counters
SES-C2
2
39”
29” 30”
5-15P
SES-C3
3
50”
29” 30”
5-15P
SES-C4
4
64”
29” 30”
5-15P
SES-C5
5
78”
29” 30”
5-15P
SES-C6
6
92”
29” 30”
5-15P
Model #
12 X 20 Pans Held
L
D
H
Plug
Amp
Shelleybasic by Delfield Hot / Cold Self-Contained Combination Counters
SES-HC2
2
39”
29” 30”
5-30P
17
SES-HC3
3
50”
29” 30”
14-30P
17
SES-HC4
4
64”
29” 30”
14-30P
22
SES-HC5
5
78”
29” 30”
14-50P
28
SES-HC6
6
92”
29” 30”
14-50P
33
Model #
12 X 20 Pans Held
L
D
H
Shelleybasic by Delfield Ice Cooled Serving Counters
SES-I2
2
39”
29” 30”
SES-I3
3
50”
29” 30”
SES-I4
4
64”
29” 30”
SES-I5
5
78”
29” 30”
SES-I6
6
92”
29” 30”
4
204
379
569
758
948
708
812
889
1373
1469
200
245
280
330
380
100
100
100
100
100
H
Plug
Amp
H.P.
Ship Wt
Ref Chrg.
30”
30”
30”
30”
30”
5-15P
5-15P
5-15P
5-15P
5-15P
7.5
7.5
7.5
7.5
8
1/4
1/4
1/4
1/4
1/3
370
445
530
600
670
24 oz.
24 oz.
24 oz.
24 oz.
24 oz.
D
H
Ship Wt
Frt Class
29”
29”
29”
29”
29”
30”
30”
30”
30”
30”
150
170
200
230
280
100
100
100
100
100
H
Ship Wt
Frt Class
30”
170
100
D
H
Ship Wt
Frt Class
29”
30”
140
100
Amp
H. P.
Ship Wt
Ref Chrg.
5
5
1/4
1/4
460
505
9 oz.
9 oz.
Model #
Cabinet Capacity
L
D
H
Plug
Shelleybasic by Delfield Ice Cream Counters - 0 degree only
SES-ICE1
210 cups
39”
29” 30”
5-15P
SES-ICE2
420 cups
50”
29” 30”
5-15P
Model #
L
Shelleybasic by Delfield Corner Units
SES-28
29”
SES-38
39”
1/5
1/5
1/4
1/4
1/4
Sys. Cap.
Frt Class
Model #
Description
L
D
Shelleybasic by Delfield Cashier’s Stand
SES-CS
Cashier’s Stand
29”
29”
Model #
Description
L
Shelleybasic by Delfield Tray Stand
SES-TS
Tray Stand
39”
BTU Load
Ship Wt
Model #
Description
L
D
Shelleybasic by Delfield Frost Top Counters
SES-F2
Frost Top
39”
29”
SES-F3
Frost Top
50”
29”
SES-F4
Frost Top
64”
29”
SES-F5
Frost Top
78”
29”
SES-F6
Frost Top
92”
29”
Model #
Description
L
Shelleybasic by Delfield Utility Counters
SES-U2
Utility, Flat Counter
39”
SES-U3
Utility, Flat Counter
50”
SES-U4
Utility, Flat Counter
64”
SES-U5
Utility, Flat Counter
78”
SES-U6
Utility, Flat Counter
92”
H.P.
D
H
Ship Wt
Frt Class
29”
29”
30”
30”
110
160
100
100
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Ref Chrg.
5.5 oz.
5.5 oz.
8 oz.
8 oz.
12 oz.
Shelleybasic by Delfield Service & Installation Manual
INSTALLATION
Location
Units represented in this manual are for indoor use only. Be
sure the location chosen has a floor strong enough to support
the total weight of the cabinet and contents. A fully loaded
model may weigh as much as 3000 pounds! Reinforce the floor
as necessary to provide for maximum loading.
For the most efficient refrigeration, be sure to provide good air
circulation inside and out. Don’t pack the refrigerator so full that
air cannot circulate. Be sure that the exterior of the unit has
access to ample air. Avoid hot corners and locations near stoves
and ovens. It is suggested the rear of the unit be no less than
two inches from any wall, partition or any other object which will
restrict exhaust air flow.
Leveling
A level cabinet looks better and will perform more efficiently
when the doors line up with the door frames properly, the
cabinet will not be subject to undue strain, and the corners of
the shelves will not move around on the supports. Use a level
to make sure the unit is level from front to back and side to side.
Stabilizing
All models are supplied on casters for your convenience, ease
of cleaning underneath and for mobility.
The unit must be installed in a stable
condition with the front wheels locked,
locking the front casters after installation is
the owner’s and operator’s responsibility.
Electrical Connection
A standard refrigerated unit is provided with a power cord and
grounded plug.
The unit should be plugged into a receptacle with its own circuit
protection that matches the amperage of the plug.
Refer to the amperage data on page 3-4, the
serial tag, your local code or the National
Electrical Code to be sure the unit is
connected to the proper power source. A
protected circuit of the correct voltage and
amperage must be run for connection of the
line cord, or permanent connection to the
unit.
On cord-connected units, an ON/OFF switch
is located directly behind the louvered panel
of the compressor section. The switch must
be turned to its OFF position and power
supply disconnected whenever doing the
following:
1. Performing maintenance functions.
2. Cleaning the refrigerated cabinet area.
3. Performing service or repair functions.
Under no circumstances should the unit be operated without the
louvered panel in place.
Plumbing
Refrigerated units have a drain that exits the unit on the bottom,
and is located on the operator’s left side. Standard units on
casters or legs will have a bronze faucet that fits a standard
garden hose. Units on legs with option remote drain valve
handle will have 1” threaded pipe extending from bottom of unit.
On standard units, a stainless steel access panel or hinged
louver will be provided for access to drain connections.
Moisture collecting from improper drainage
can create a slippery surface on the floor
and a hazard to employees. It is the owner’s
and operator’s responsibility to provide a
container or outlet for drainage.
Installation Heated Units
Location
Do not install the unit near combustible objects or surfaces
affected by heat or moisture
Leveling
The unit must be level, both front and back and left to right, in
order to maintain an equal water depth throughout the wells.
Electrical Connections
Connections must be made in accordance
with all applicable local codes and/or the
National Electrical Code. Refer to the
amperage data on page 3 and the wiring
diagrams on pages 8 and 9. A standard unit
is provided with a power cord and grounded
plug. All units must be plugged into a
grounded receptacle with its own circuit
protection that matches the amperage of the
plug.
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
5
Shelleybasic by Delfield Service & Installation Manual
OPERATION SE-C AND SES-C
Cold pans are adjusted at the factory to provide satisfactory
operation without any further adjustments. However, if it is
necessary to adjust the temperature, the control is located in the
machine compartment. Turn the knob clock-wise as indicated
on the control. Settings are from 1 through 7; 7 being the
coldest. Adjustments should be made gradually. Several small
adjustments will be more effective than one large adjustment. It
may take an hour or longer to realize the temperature change
depending on the application and location of the unit.
may be necessary to maintain overall temperature. Warming of
food product can occur very quickly outside of the unit. When
loading or rotating product, avoid leaving food items in a nonrefrigerated location to prevent warming or spoilage.
These units are not designed to cool warm food products. Items
should be placed in the unit pre-cooled at least to the desired
holding temperature, if not slightly colder. In some applications,
a gradual warming of product may occur, particularly at the
exposed top of the product. Stirring or rotation of the product
If the cold pan is to be used with ice, it is recommended that
the optional perforated bottoms be used. These will allow ice
to melt properly.
The temperature control is used to turn the unit on and off as
well as control the temperature of the cold pan. The settings
range from 1 through 7; 7 being the coldest. To turn the cold
pan off, turn the knob to the off position.
OPERATION SE-H AND SES-H
These units are designed to hold warm food product between
140˚F to 160˚F (60˚C to 71˚C).
Individually heated hot food units may be operated “wet” (with
water in the wells) or “dry”. However, “wet” operation is usually
recommended for higher efficiency.
After plugging in the power supply cord, select desired
temperature by rotating the knob on the temperature control.
Knobs and indicator lights are provided for each heated food
well.
Before the unit is used the first time for serving, turn the
temperature knob to “HI” and heat the well for 10 to 15 minutes.
Do not be alarmed if smoke appears; this preheat should
burn off any residue or dust that has adhered to the food well
element.
When using thick sauces, always operate the hot food well filled
with water. This will provide more uniform temperature for the
sauce.
Never place food directly in well. Always use
pans.
For most efficient operation, when empty, place covered insets
in each well during preheating and when the well is not in use.
Always place covers on pans when not serving to prevent food
from drying out and to reduce your operating costs.
Wet Operation
Fill the food well with about 2 gallons of water and cover with lid
or empty pan. To preheat water, set temperature control at “HI”
with pans in place, wells will boil water.
6
Food temperature will vary depending on type and amount
of product. To minimize steam and water usage, set control
to lowest setting that will maintain safe food temperature. To
reduce preheating time, use hot water to fill the well.
When operating these units “wet”, never use
anything other than plain water in the wells
or tank. Failure to observe this warning may
result in personal injury or damage to the unit.
When operated at the highest temperature
setting, the top of the unit will become very
hot. Staff and customers using the equipment
should be informed about this.
Steam can cause serious burns. Always wear
some type of protective covering on your
hands and arms when removing lids from
the unit. Lift the lid in a way that will direct
escaping steam away from your face and body.
Dry Operation
Wet operation is usually much more efficient and is usually
preferred. However, these units may be operated without water
with no damage to the unit.
When operated dry, the bottom of the well will discolor. To
clean, use a stainless steel cleaner or mild abrasive.
The dry well should never be preheated longer
than 15 minutes. Only 6” deep pans should be
used with dry food wells.
When operated dry, the well bottoms become
very hot. Do not allow unprotected skin to
contact any well surface.
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Shelleybasic by Delfield Service & Installation Manual
OPERATION SE-F AND SES-F
Frost tops are designed to maintain an even layer of frost to
pleasantly display desserts and pies. Once turned on, the
compressor will run continuously. The unit should be turned off
overnight or when not in use.
Since it takes some time for frost to accumulate initially, the unit
should be turned on approximately an hour before it is actually
required. Product should not be placed on the frost top prior to
turning the unit on, because it may freeze to the surface of the
unit.
OPERATION SE-HC AND SES-HC
The hot and cold combination pans must be operated with water
in the well for proper hot performance. It is also recommended
that ice be used in conjunction with the refrigeration system for
best cold performance.
Hot Operation
Place water in pan. Place function switch in HOT position. Turn
thermostat dial to highest position and allow unit to warm up.
Then reset the thermostat to maintain the desired temperature.
When operating these units “wet,” never use
anything more than plain water in the wells
or tank. Failure to observe this warning may
result in personal injury or damage to the unit.
When operated at the highest temperature
setting, the top of the unit will become very
hot. Staff and customers using the equipment
should be informed about this.
To turn unit off, simply move the function switch to OFF position.
Drain water and allow unit to cool before cleaning or switching
to cold operation.
Read the section on “Switching from Hot to Cold Operation”
before changing temperatures on the unit.
Cold Operation
Simply place the function switch to the COLD position. The
compressor controller has been factory set and no temperature
adjustment should be necessary. The unit may be operated
with or without ice. However, for best results it is recommended
that ice be used. The refrigeration system will keep ice usage
to a minimum while the ice helps maintain a constant, usually
ideal, holding temperature.
Switching from Hot to Cold Operation
Follow the following procedure:
1) Place the function switch in the OFF position
and drain off hot water.
2) Allow the unit to cool until it can be safely
cleaned.
3)
When clean up procedures are complete,
unit will be ready for cold operation.
To assure maximum compressor life, do not
switch from “hot” to “cold” operation without
allowing a cool down period. Never switch from
hot to cold operation while hot water remains in
the pans. Failure to observe this warning will
greatly reduce compressor life and eventually
cause premature compressor failure.
Switching from Cold to Hot Operation
No special procedure is required to switch from cold to hot
operation.
This unit is designed so that the compressor and the heating
elements cannot operate at the same time. Continued or
repeated operation of the compressor in the “hot” position
should not be considered normal. Before calling for Service, try
switching quickly from HOT to COLD and back to HOT
HOT. If the
compressor still does not shut off or continues to cycle on and
off, call for service.
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
7
Shelleybasic by Delfield Service & Installation Manual
ROUTINE MAINTENANCE
Cleaning the unit
To clean refrigerated understorage, use mild soap and water.
For all fiberglass and stainless steel parts, use a mild, nonabrasive soap or detergent and warm water. This may be
followed by an application of stainless steel cleaner or polish
which will eliminate water spotting, fingerprints and bring out
the color of the fiberglass.
To maintain the rich, brilliant color of the fiberglass and to
remove shallow surface scratches, wax twice a year. This can
be done in the same manner in which a car is waxed.
Cleaning the Condenser
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt, and grease
regularly. It is recommended that this be done at least every
three months. If conditions are such that the condenser is
totally blocked in three months, the frequency of cleaning should
be increased. Clean the condenser with a vacuum cleaner
or stiff brush. If extremely dirty, a commercially available
condenser cleaner may be required.
Do not use a hose or pressure washer on
these units. The water will damage the
electrical components.
Casters
Casters can be lubricated with penetrating type oil.
Recommended maintenance schedule:
Daily: Wipe and/or wash food wells, unit surface, any
refrigerated understorage and door gaskets.
Monthly: Remove louvers and clean condensing coil with
a soft brush, such as a fin comb, or vacuum cleaner brush
attachment. The object is to remove dust and webs from fins
without bending them. Check casters for any debris that could
be binding the wheels such as strings from mops or bits of
paper.
Every six months: Wax fiberglass body and if necessary,
lubricate casters.
Defrosting
Refrigerated cold pans and frost tops should be defrosted
daily. Milk or Ice Cream dispensers require defrosting after
3/8” to 1/2” of frost forming. On/Off switch located above
louver panel.
Never use sharp objects or tools to clean or scrape ice/
frost build up from the refrigerated cold pans or frost
tops. A puncture to the pan could cause irreparable
damage to the refrigeration system.
Units with a Eutectic Fluid Cold Pan require the same
precautions. The fluid is NOT refillable and loss of fluid
due to a puncture would cause irreparable damage.
Over shelves and other items mounted to the top of the
counters should never be installed in the field due to the
potential damage to the refrigeration system.
8
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Shelleybasic by Delfield Service & Installation Manual
WIRING DIAGRAM SE-C/SES-C
CONDENSER FAN
S
C
L1
COOLING T'STAT
R
COMPRESSOR
120V
N
RECEPTACLE FOR OPTIONAL
LOW VOLTAGE COOLING FANS
G
WIRING DIAGRAM SE-F/SES-F
ON/OFF SWITCH
L1
CONDENSER FAN
S
C
R
COMPRESSOR
120V
N
G
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
9
Shelleybasic by Delfield Service & Installation Manual
WIRING DIAGRAM SE-H/SES-H
PILOT LIGHT
(FURNISHED)
H1
1000 W - 120V
OR 1000/1200 W 208/240 V
HEATING ELEMENT
P
L1
L2
H2
LINE
WIRES
INFINITE CONTROL
WITH “OFF”
POSITION
TO ADDITIONAL
FOOD WARMERS
AMPERES IN LINE WIRES
208/240V, 3 PHASE
# OF
WARMERS
1
L1
120V,
1 PHASE
9
208V,
1 PHASE
5
240V,
1 PHASE
5
2
17
10
10
3
25
15
15
4
33
L1
L2
L3
10
10
10
10
19
20
15
15
5
24
26
20
15
15
6
29
31
20
20
20
G
L1
L2(N)
L2
G
LS
20A, 3–POLE SWITCH
(OPTIONAL)
30A SWITCH
(OPTIONAL)
HA–1
HA–1
HA–2
HA–2
ALL WIRING
MINIMUM 14 AWG
250°C
HA–3
HA–3
HA–4
HA–4
HA–5
HA–5
HA–6
HA–6
HA = HEATER ASSEMBLY
Standard Single Phase
10
HA = HEATER ASSEMBLY
Optional Three Phase
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Shelleybasic by Delfield Service & Installation Manual
WIRING DIAGRAM SE-HC2/SES-HC2
Self-contained units
L1
WIRING FOR HOT/COLD SERIES
115V MODELS WITH ONE TO TWO HEATERS
R-134A CAP TUBE REFRIGERATION SYSTEM
G
N
POWER LEADS
#14 AWG MIN FOR 1 HEATER
#12 AWG MIN FOR 2 HEATERS
CONDENSER FAN
FUNCTION
SWITCH
#14 MTW
COLD
OFF
HOT
C
S
R
COMPRESSOR
115V
COOLING T' STAT
HEATER 1
HEATING T' STAT
HEATER 2
PILOT LIGHT
#14 TGGT
WIRING DIAGRAM SE-HC3/SES-HC3 AND SE-HC4/SES-HC4
WIRING FOR HOT/COLD SERIES,
115/208-230V MODELS WITH THREE OR
FOUR HEATERS R-134A CAP TUBE
REFRIGERATION SYSTEM
FUNCTION
SWITCH
L1 G
#14 MTW
COLD
OFF
COOLING T' STAT
HOT
HEATING T' STAT
N L2
POWER LEADS
#12 AWG MIN FOR 3 HEATERS
#10 AWG MIN FOR 4 HEATERS
CONDENSER FAN
S
C
R
COMPRESSOR
115V
HEATER 1
HEATER 2
HEATER 3
HEATER 4
PILOT LIGHT
#14 TGGT
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
11
Shelleybasic by Delfield Service & Installation Manual
WIRING DIAGRAM SE-HC5/SES-HC5 AND SE-HC6/SES-HC6
L1 G
WIRING FOR HOT/COLD SERIES,
115/208-230V MODELS W/ FIVE OF
SIX HEATERS, R-134A CAP TUBE
REFRIGERATION SYSTEM
N L2
POWER LEADS
#10 AWG MIN FOR 5 HEATERS
#8 AWG MIN FOR 6 HEATERS
#14 MTW
FUNCTION
SWITCH
CONDENSER FAN
S
C
COLD
OFF
HOT
#14 MTW
COOLING T' STAT
R
COMPRESSOR
115V
HEATING T' STAT
CONTACTOR "C1"
115V COIL
#12 TGGT
HEATER 1
#12 TGGT
HEATER 2
HEATER 3
C1
HEATER 4
C1
HEATER 5
HEATER 6
PILOT LIGHT
12
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
#14 TGGT
Shelleybasic by Delfield Service & Installation Manual
REPLACEMENT PARTS LIST
DELFIELD PART #
3234161
3547588
3547374
DESCRIPTION
5” caster (6” load height)
1/5 h.p. cap tube system (6 ft.) 0.036”(id) x 72” long
1/4 h.p. cap tube system (10 ft.) 0.042”(id) x 120” long
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
13
Shelleybasic by Delfield Service & Installation Manual
CONDENSING UNIT ASSEMBLY 1/4 h.p. and 1/3 h.p.
3
6
4
5
1
2
1/4 HORSE POWER
1/3 HORSE POWER
Key
1
2
3
4
5
6
7
Key
1
2
3
4
5
6
7
R-404a, Low
14
Qty
1
1
1
1
1
1
2
Delfield Part #
352-6716
036-0327
036-0325
351-6101
354-7508
354-7476
619-0010
Description
condensing unit, 1/4 h.p., low, R-404a, NB
switch, assembly, with bracket
heat exchanger assembly, condensing unit
dryer, filter, 1/4” ODF, sporlan
nut, flare, 1/4” x 1/4”
nut, flare, 3/8” x 3/8”
nut, wire
R-404a, Low
Qty
1
1
1
1
1
1
2
Delfield Part #
352-6710
036-0327
036-0325
351-6011
354-7508
354-7476
619-0010
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Description
condensing unit, 1/3 h.p., low, R-404a, NB
switch, assembly, with bracket
heat exchanger assembly, condensing unit
dryer, filter, 1/4” dia.in/out
nut, flare, 1/4” x 1/4”
nut, flare, 3/8” x 3/8”
nut, wire
Shelleybasic by Delfield Service & Installation Manual
CONDENSING UNIT ASSEMBLY 1/5 h.p.
7
1
6
11
8
10
9
11
2
3 4
5
1/5 HORSE POWER
R-134a, Low
Key
1
2
3
4
5
6
7
8
9
10
11
Qty
1
1
1
1
1
1
1
1
1
1
2
Delfield Part #
352-6694
AMK00021
351-6172
216-2691
351-6047
397-7986
218-3300
3516047
GMK00207
GMK00208
GMK00203
Description
compressor, 1/5 h.p.,115v/60hz
bracket, fan motor, blower coil
blade, fan, 5.56, CCW, Lexan, clear
motor, fan, 115v, 50/60, UPPCO/bay
coil, condenser, 9 x 10, R-134a, 8100
guard, wire, fan, condenser unit, 8100
harness, wire, power cord, 8100
thermostat
fan baffle
compressor stand
access cover
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
15
Shelleybasic by Delfield Service & Installation Manual
FOOD WELL ASSEMBLY WITH INFINITE CONTROL
3
6
5
4
2
2
1
7
16
Key
1
1
2
3
3
4
4
5
6
7
Delfield Part #
219-4110
219-4107
036-0306 (016-0009)
036-0267(016-0008)
343-4703
3234357
3234349
219-4007
219-4006
219-4335
343-4664
323-4557
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Description
control, infinite, 240v, 14a
control, infinite, 120v
well, hot food, without drain
well, hot food, with drain
insulation, fiberglass, 9” x 48”
plate, deflector, DFW, with drain
plate, deflector, DFW, without drain
element, heating, 208/230v, 1000w
element, heating, 120v
thermostat, non-adjustable, 550˚F
insulation, blanket, 24” wide
knob, infinite control
Shelleybasic by Delfield Service & Installation Manual
NOTES:
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
17
Shelleybasic by Delfield Service & Installation Manual
STANDARD LABOR GUIDELINES TO REPAIR OR REPLACE PARTS ON DELFIELD EQUIPMENT
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
• A maximum of 1-hour is allowed to diagnose a defective component.
• A maximum of 1-hour is allowed for retrieval of parts not in stock.
• A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
• Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
LABOR OF 1-HOUR IS ALLOWED TO REPLACE:
• Thermostat
• Infinite Switch
• Door Jamb Switch
• Solenoid Coil
• Hi-limit/Thermal Protector Switch
• Fan Delay/Defrost Termination Switch
• Compressor Start Components and Overload Protector
• Defrost Timer
• Thermometer
• Gear Box
•
•
•
•
•
•
•
•
•
Contactor/Relay
Transformer
Evaporator/Condenser Fan Motor and Blade
Circulating Fan Motor and Blade
Microprocessor Control
Water Level Sensor/Probe
Door Hinges, Locks, and Gaskets
Condensate Element
Springs/Lowerator
LABOR OF 2 HOURS TO REPLACE:
• Drawer Tracks/Cartridges
• Defrost Element
• Pressure Control
• Heating Element
• Solenoid Valve
• Locate/Repair Leak
LABOR OF 3 HOURS TO REPLACE:
• EPR or CPR Valve
• Condenser or Evaporator Coil
• Expansion Valve
LABOR OF 4 HOURS TO REPLACE
• Compressor
This includes recovery of refrigerant and leak check.
$35.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings,
solder, brazing rod, nitrogen, or similar fees.)
REFRIGERANTS
• R22 A maximum of $4.00/lb. or 25¢/oz. will be reimbursed.
• R134A A maximum of $5.00/lb. or 31¢/oz. will be reimbursed.
• R404A A maximum of $12.00/lb. or 75¢/oz. will be reimbursed.
18
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Shelleybasic by Delfield Service & Installation Manual
STANDARD ONE YEAR WARRANTY (ONE YEAR PARTS, 90 DAYS LABOR.)
The Delfield Company (“Delfield”) warrants to the Original Purchaser
of the Delfield product (herein called the “Unit”) that such Unit, and all
parts thereof, will be free from defects in material and workmanship
under normal use and service for a period of one (1) year from
the date of shipment of the Unit to the Original Purchaser or, if the
Original Purchaser returns the warranty card completely filled out
including the date of installation within thirty (30) days of receipt
of the Unit, one (1) year from the date of installation. During this
one year warranty period, Delfield will repair or replace any defective
part or portion there of returned to Delfield by the Original Purchaser
which Delfield determines was defective due to faulty material or
workmanship. The Original purchaser will pay all labor, crating, freight
and related costs incurred in the removal of the Unit of defective
component and shipment to Delfield, except that during a period of
either ninety (90) days from the date of shipment of the Unit to the
Original Purchaser or, if the Original Purchaser returns the warranty
card completely filled out including the date of installation within thirty
(30) days of receipt of the Unit, ninety (90) days from the date of
installation Delfield will pay all related labor costs. Delfield will pay the
return costs if the Unit or part thereof was defective.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
This warranty does not apply to any Unit or part thereof that has
been subjected to misuse, neglect, alteration, or accident, such as
accidental damage to the exterior finish, operated contrary to the
recommendations specified by Delfield; or repaired or altered by anyone
other than Delfield in any way so as to, in Delfield’s sole judgement,
affect its quality or efficiency. This warranty does not apply to any Unit
that has been moved from the location where it was originally installed.
This warranty also does not cover the refrigerator drier or the light
bulbs used in the Unit. The warranty is subject to the user’s normal
maintenance and care responsibility as set forth in the Service and
Installation Manual, such as cleaning the condenser coil, and is in
lieu of all other obligations of Delfield. Delfield neither assumes, nor
authorizes any other person to assume for Delfield, any other liability
in connection with Delfield’s products.
Removal or defacement of the original Serial Number or Model Number
from any Unit shall be deemed to release Delfield from all obligations
hereunder or any other obligations, express or implied.
Parts furnished by suppliers to Delfield are guaranteed by Delfield only
to the extent of the original manufacturer’s express warranty to Delfield.
Failure of the Original Purchaser to receive such manufacturer’s express
warranty to Delfield. Failure of the Original Purchaser to receive such
manufacturers warranty shall in no way create any warranty, expressed
or implied, or any other obligation or liability on Delfield’s part in respect
thereof.
IF THE CUSTOMER IS USING A PART THAT RESULTS IN A VOIDED
WARRANTY AND A DELFIELD AUTHORIZED REPRESENTATIVE
TRAVELS TO THE INSTALLATION ADDRESS TO PERFORM WARRANTY
SERVICE, THE SERVICE REPRESENTATIVE WILL ADVISE CUSTOMER
THE WARRANTY IS VOID. SUCH SERVICE CALLS WILL BE BILLED
TO CUSTOMER AT THE AUTHORIZED SERVICE CENTER’S THEN
APPLICABLE TIME AND MATERIALS RATES. CONSIDER: CUSTOMER
MAY INITIATE A SERVICE AGREEMENT WITHOUT PARTS COVERAGE.
If shipment of a replacement part is requested prior to the arrival in
the Delfield factory of the part claimed to be defective, the Original
Purchaser must accept delivery of the replacement part of a C.O.D.
basis, with credit being issued after the part has been received and
inspected at Delfield’s plant and determined by Delfield to be within this
warranty.
Under no condition does this warranty give the Original Purchaser the
right to replace the defective Unit with a complete Unit of the same
manufacturer or of another make. Unless authorized by Delfield in
writing, this warranty does not permit the replacement of any part,
including the motor-compressor, to be made with the part of another
make or manufacturer.
No claims can be made under this warranty for spoilage of any products
for any reason, including system failure.
The installation contractor shall be responsible for building access,
entrance and field conditions to insure sufficient clearance to allow any
hood(s), vent’s), or Unit’s) if necessary, to be brought into the building.
Delfield will not be responsible for structural changes or damages
incurred during installation of the Unit or any exhaust system.
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war,
governmental restrictions or restraints, strike, lockouts, injunctions,
fire, flood, acts of nature, short or reduced supply of raw materials, or
discontinuance of the parts by the original part manufacturer.
Except as provided in any Additional Four Year Protection Plan,
if applicable, and the Service Labor Contract, if applicable, the
foregoing is exclusive and in lieu of all other warranties, whether
written or oral, express or implied. This warranty supersedes
and excludes any prior oral or written representations or
warranties. Delfield expressly disclaims any implied warranties
of merchantability, fitness for a particular purpose of compliance
with any law, treaty, rule or regulation relating to the discharge of
substances into the environment. The sole and exclusive remedies
of any person relating to the Unit, and the full liability of Delfield for
any breach of this warranty, will be as provided in this warranty.
Other than this Delfield Standard One Year Limited Warranty, any
applicable Delfield Additional Four Year Protection Plan or applicable
Delfield Service Labor Contract, the Original Purchaser agrees and
acknowledges that no other warranties are offered or provided in
connection with or for the unit or any other part thereof.
In no event will Delfield be liable for special, incidental or consequential
damages, or for damages in the nature of penalties.
IF DURING THE WARRANTY PERIOD, CUSTOMER USES A PART FOR
THIS DELFIELD EQUIPMENT OTHER THAN AN UNMODIFIED NEW
OR RECYCLED PART PURCHASED DIRECTLY FROM DELFIELD OR
ANY OF ITS AUTHORIZED SERVICE CENTERS AND/OR THE PART
BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION,
THIS WARRANTY WILL BE VOID. FURTHER, DELFIELD AND ITS
AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS DAMAGES OR
EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY
OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION
OF ANY MODIFIED PART AND/OR PART RECEIVED FROM AN
UNAUTHORIZED SERVICE CENTER. If the warranty becomes void,
Customer may purchase from Delfield, if available, a Service
Agreement or service at the then current time and materials rate.
For more information on Delfield warranty’s log on and check out the
service section of our web site at www.delfield.com.
For customer service, call (800) 733-8948, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
19
NORTH
AMERICA
12
8
5
1
11
15
10
6
4
4
2
3 16
14
13
7
9
12
Delfield has 16 conveniently located Parts Depots to ensure parts are handled promptly and accurately.
1) The Delfield Company
980 South Isabella Road
Mt. Pleasant, MI 48858
800.733.8829
989.773.7981
989.773.3210 FAX
custom parts direct from Delfield
5) Contract Ice
2) A.I.S. Commercial Parts & Service
3) Appliance Installation Service
1816 West 26th Street
Erie, PA 16508-1149
800.332.3732
814.456.3732
814.452.4843 FAX
1336 Main Street
Buffalo, NY 14209
800.722.1252
716.884.7425
716.884.0410 FAX
serves: MD, NJ, OH, PA, VA, WV
serves: CT, DC, DE, MA, MD, ME,
NH, NJ, NY, PA, RI, VA, VT, WV
6) E.M.C.O. Sales & Distributors
7) Stove Parts Supply/GCS Service
14450 Ewing Ave S. #100
Burnsville, MN 55306
800.422.2823
952.894.4427
952.894.2164 FAX
3909 St. Timothy Lane
St. Ann, MO 63074
800.972.7670
314.427.7477
314.427.8190 FAX
2120 Solona St.
PO Box 14009
Fort Worth, TX 76117-0009
800.433.1804
800.272.7358 fax
serves: IA, MN, MT, ND, SD, WI
serves: AR, IA, IL, KS,
KY, MO, NE, OK, TX, NM, LA
serves: AR, LA, NM, OK, TX
9) Global Parts and Supplies
10) Hawkins Commercial Appl. Serv.
2920 N.W. 109th Avenue
Miami, FL 33172
305.994.9994
305.994.9992 FAX
3000 S. Wyandot
Englewood, CO 80110
800.624.2117
303.761.8861 FAX
International parts depot
serves: AZ, CO, KS, NE, NM, OK, UT, WY
11) MicroDine, Inc.
44792 Helm
Plymouth, MI 48170
888.828.4454
734.451.2043
734.451.3215 FAX
serves: MI, IN, WI, OH
13) Southeastern Restaurant Services
15) Heritage Food Serv. Equip. Inc.
14) T.M.A.
2200 Norcross Parkway, Suite 210
Atlanta, GA 30071
800.235.6516
770.446.6177
770.446.3157 FAX
2916 Sidco Drive
Nashville, TN 37204
615.726.0351
800.737.0351
615.259.4100 FAX
serves: FL, GA, MS, NC, SC, VA
serves: TN, AL
4) Pacific Coast Parts
15024 Staff Court
Gardena, CA 90248
800.531.1111
800.782.5747
Email: orders@pacparts.com
www.pacparts.com
serves: AZ, CA, HI, NV, OR
8) Garland Group
1177 Kamato Road
Mississauga, Ontario L4W1X4
800.427.6668
800.361.7745 FAX
serves: Canada
12) Performance Refrigeration Parts
9923 S.W. 178th St.
Vashon, WA 98070
888.872.2465
206.463.1772
206.463.4431 FAX
serves: AK, HI, ID, MT, OR, WA
16) Northern Parts & Service
5130 Executive Blvd.
Fort Wayne, IN 46808
800.458.5593
800.800.4981 FAX
21 Northern Avenue
Plattsburgh, NY 12903
800.634.5005
800.782.5424 FAX
serves: IL, IN, MI, OH, WI
serves: CT, DC, DE, MA, MD, ME,
NH, NJ, NY, PA, RI, VA, VT, WV
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2004 The Delfield Company. All rights reserved. Printed in the U.S.A.
DMSHELLEYBASIC 02/04