UDX series
User Manual
R5906112/01
24/05/2017
Product revision
Software version: 1.2
Barco NV
Beneluxpark 21, 8500 Kortrijk, Belgium
Phone: +32 56.23.32.11
Fax: +32 56.26.22.62
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Printed in Belgium
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site
https://www.barco.com/en/signin.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in
the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures
which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal
maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the
customer.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment
EMC statements
EN55032/CISPR32 Class A MME (MultiMedia Equipment)
Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.
Class A ITE (Information Technology Equipment)
Warning : This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
Table of contents
TABLE OF CONTENTS
1. Safety . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 3
1.1
1.2
1.3
1.4
1.5
1.6
General considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Product safety labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
High Brightness precautions: Hazard Distance (HD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
HD for fully enclosed projection systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HD in function of modifying optics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. Remote Control Unit . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 13
2.1
2.2
2.3
Remote control, Battery installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Using the XLR connector of the RCU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Remote control, on/off button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3. Input & Communication . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 15
3.1
3.2
3.3
3.4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Input source connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Communication connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
LED and Button indication chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4. Getting Started.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 25
4.1
4.2
4.3
4.4
4.5
4.6
Functionality overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Power on projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Switching to standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Power off projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Using the RCU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Projector Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.6.1 Controlling the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.6.2 Displaying and Programming addresses into the RCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.7 Quick setup via Direct access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5. Graphic User Interface (GUI) . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 33
5.1
5.2
5.3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Test Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6. GUI – Source .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 37
6.1
6.2
Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Connector Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7. GUI – Image . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 39
7.1
7.2
7.3
Setting image levels manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
P7 Realcolor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 40
Setting the output resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8. GUI – Installation . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 43
8.1
8.2
8.3
Configuring the lens, shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Warping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.3.1 About warping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.3.2 Warping – On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.3.3 Warping – Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.3.4 Warping – 4 corners adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8.3.5 Warping – Bow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
8.4 Blending. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
8.4.1 Blend Zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
8.5 Laser illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
9. GUI – System Settings. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 53
9.1
9.2
9.3
9.4
9.5
9.6
Communication, LAN setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9.1.1 Introduction to a Network connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9.1.2 Wired IP address set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
GSM configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
IR control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
9.3.1 Broadcast address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
9.3.2 Projector address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
9.3.3 IR sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Themes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Service Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
9.5.1 Service – Color. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
9.5.2 Service – Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
9.5.3 Lens Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
9.5.4 Lens features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
R5906112 UDX SERIES 24/05/2017
1
Table of contents
10. Status menu . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 65
10.1 Status menu overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
11. Maintenance. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 67
11.1 Cleaning the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
11.2 Cleaning the exterior of the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
A. Specifications .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 69
A.1
A.2
A.3
A.4
A.5
A.6
A.7
A.8
A.9
Specifications of the UDX 4K32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Specifications of the UDX 4K22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Specifications of the UDX W32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Specifications of the UDX W22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Specifications of the UDX U32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Dimensions of a UDX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Dimensions of the rigging frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Dimensions of the flight case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Technical Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
B. Environmental information .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 77
B.1
B.2
B.3
B.4
2
Disposal information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Turkey RoHS compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Contact information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Download Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
R5906112 UDX SERIES 24/05/2017
1. Safety
1. SAFETY
About this document
Read this document attentively. It contains important information to prevent personal injury while installing and using the UDX projector. Furthermore, it includes several cautions to prevent damage to the UDX projector. Ensure that you understand and follow all
safety guidelines, safety instructions and warnings mentioned in this chapter before installing the UDX projector.
Clarification of the term “UDX” used in this document
When referring in this document to the term “UDX” means that the content is applicable for following Barco products:
•
UDX 4K22
•
UDX 4K32
•
UDX U32
•
UDX W22
•
UDX W32
Model certification name
•
UDX
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. Observing the specification mentioned in this chapter is critical for projector performance. Neglecting
this can result in loss of warranty.
1.1
General considerations
WARNING:
Be aware of suspended loads.
WARNING:
Wear a hard hat to reduce the risk of personal injury.
WARNING:
Be careful while working with heavy loads.
WARNING:
Mind your fingers while working with heavy loads.
General safety instructions
•
Before operating this equipment please read this manual thoroughly and retain it for future reference.
•
Installation and preliminary adjustments should be performed by qualified Barco personnel or by authorized Barco service dealers.
•
All warnings on the projector and in the documentation manuals should be adhered to.
•
All instructions for operating and use of this equipment must be followed precisely.
•
All local installation codes should be adhered to.
Notice on safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1,
UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including
electrical business equipment. These safety standards impose important requirements on the use of safety critical components,
materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access
to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability
R5906112 UDX SERIES 24/05/2017
3
1. Safety
and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing ensures the
safety of the equipment to the user even when the equipment’s normal operation fails.
Notice on optical radiation
This projector embeds extremely high brightness (radiance) lasers; this laser light is processed through the projectors optical path.
Native laser light is not accessible by the end user in any use case. The light exiting the projection lens has been diffused within the
optical path, representing a larger source and lower radiance value than native laser light. Nevertheless the projected light represents a significant risk for the human eye when exposed directly within the beam. This risk is not specific related to the characteristics
of laser light but solely to the high thermal induced energy of the light source; which is equivalent with lamp based systems.
Thermal retinal eye injury is possible when exposed within the Hazard Distance (HD). The HD is defined from the projection lens
surface towards the position of the projected beam where the irradiance equals the maximum permissible exposure as described in
the chapter “Hazard Distance”.
WARNING: No direct exposure to the beam within the hazard distance shall be permitted, RG3 IEC 624715:2015
CAUTION:
Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to persons having appropriate technical training and experience
necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize
the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE PERSONNEL, AUTHORIZED to operate professional projection systems.
The UDX projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards
associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures generated by the lamp and
associated circuits. Only qualified SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions
inside the product enclosure.
1.2
Important safety instructions
To prevent the risk of electrical shock
4
•
This product should be operated from a mono phase AC power source. Ensure that the mains voltage and capacity matches
the projector electrical ratings (120-160V / 200-240V (+/- 10%), 20A, 50-60Hz). If you are unable to install the AC requirements,
contact your electrician. Do not defeat the purpose of the grounding.
•
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If you are unable to insert the plug
into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
•
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect
the cord, pull it out by the plug. Never pull the cord itself.
•
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
•
Do not operate the projector with a damaged cord. Replace the cord.
•
Do not operate the projector if the projector has been dropped or damaged - until it has been examined and approved for
operation by qualified service personnel.
•
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated
for less amperage than the projector may overheat.
•
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electrical shock.
•
Do not expose this projector to rain or moisture.
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
•
Do not disassemble this projector, always take it to qualified service personnel when service or repair work is required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
•
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.
R5906112 UDX SERIES 24/05/2017
1. Safety
To prevent personal injury
•
To prevent injury and physical damage, always read this manual and all labels on the system before powering the projector or
adjusting the projector.
•
To prevent injury, take note of the weight of the projector. Minimum 2 persons are needed to carry the projector. The projector
weights about ±90 kg (±198 lbs) without lens and rigging frame.
•
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
•
Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
•
Warning: extremely high brightness projector: This projector embeds extremely high brightness (radiance) lasers; this laser
light is processed through the projectors optical path. Native laser light is not accessible by the end user in any use case. The
light exiting the projection lens has been diffused within the optical path, representing a larger source and lower radiance value
than native laser light. Nevertheless the projected light represents a significant risk for the human eye when exposed directly
within the beam. This risk is not specific related to the characteristics of laser light but solely to the high thermal induced energy
of the light source; which is comparable with lamp based systems.
Thermal retinal eye injury is possible when exposed within the Hazard Distance. The Hazard Distance (HD) is defined from
the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible
exposure as described in the chapter "High Brightness precautions: Hazard Distance (HD)", page 8 .
•
High Brightness Warning: The projector light source may not be switched on or the shutter must be closed when no projection
lens is installed.
•
Based on international requirements, no person is allowed to enter the projected beam within the zone between the projection
lens and the related Hazard Distance (HD). This shall be physically impossible by creating sufficient separation height or by
placing optional barriers. Within the restricted area operator training is considered sufficient. The applicable separation heights
are discussed in "High Brightness precautions: Hazard Distance (HD)", page 8 .
•
Don’t put your hand in front of the beam.
•
Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall outlet.
•
When required to switch off the projector, to access parts inside, always disconnect the power cord from the power net.
•
The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to
access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side is not
accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily
accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
•
Never stack more than 2 UDX projectors in a hanging configuration (truss) and never stack more than 3 UDX projectors in a
base stand configuration (table mount).
•
When using the projector in a hanging configuration, always mount 2 safety cables. See installation manual for the correct use
of these cables.
•
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and
possible injury to the user.
•
It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become
visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.
•
Cooling liquid circuit. The projector contains a cooling circuit filled with Mono-ethylene glycol (1,2-ethane diol) and inhibitors
in aqueous solution (34% active). When the cooling circuit leaks, switch off the device and contact qualified service personnel.
The liquid is not for household use. Keep out of reach of children. Harmful by oral intake. Avoid exposure to pregnant women.
Avoid contact with eyes, skin and clothing. Avoid inhale of the noxious fumes.
•
Never point or allow light to be directed on people or reflective objects within the HD zone.
•
All operators shall have received adequate training and be aware of the potential hazards.
•
In case of using an external cooling system position the hoses of the cooling system so that they will not be tripped over, pulled,
or contact hot surfaces.
R5906112 UDX SERIES 24/05/2017
5
1. Safety
To prevent fire hazard
•
Do not place flammable or combustible materials near the projector!
•
Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This
projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and
safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition
of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external
surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone must be not less
than 40 cm (16”) for this projector. The exclusion zone on the lens side must be at least 5 m. Do not cover the projector or the
lens with any material while the projector is in operation. Keep flammable and combustible materials away from the projector at
all times. Mount the projector in a well ventilated area away from sources of ignition and out of direct sun light. Never expose
the projector to rain or moisture. In the event of fire, use sand, CO 2 or dry powder fire extinguishers. Never use water on an
electrical fire. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine
Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this projector.
•
Ensure no misalignment can occur. Prolonged exposure of wooden walls at close distance (< 20 cm) can represent a fire risk.
After alignment the projector shall be securely mounted to the pedestal.
•
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent hot exhaust air from
projector and cooling system to the outside of the building.
•
Let the projector cool completely before storing. Remove cord from the projector when storing.
To prevent battery explosion
•
Danger of explosion if battery is incorrectly installed.
•
Replace only with the same or equivalent type recommended by the manufacturer.
•
For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations
to ensure proper disposal.
To prevent projector damage
6
•
The air filters of the projector must be cleaned or replaced on a regular basis. Cleaning the booth area would be monthlyminimum. Neglecting this could result in disrupting the air flow inside the projector, causing overheating. Overheating may lead
to the projector shutting down during operation.
•
The projector must always be installed in a manner which ensures free flow of air into its air inlets.
•
If more than one projector is installed in a common projection booth, the exhaust air flow requirements are valid for EACH
individual projector system. Note that inadequate air extraction or cooling will result in decreased life expectancy of the projector
as a whole as well as causing premature failure of the lasers.
•
In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC)
and safety requirements, it should always be operated with all of it’s covers in place.
•
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product
on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The
device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and remove all power
from the projector. Do not operate the projector again until it has been checked by qualified service personnel.
•
Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not be
nearer to the projector than 10 cm (4") on any side.
•
Do not use this equipment near water.
•
Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power
laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices TM in
which case there is a loss of warranty.
•
Never place the projector in direct sunlight. Sunlight on the lens can severely damage the Digital Mirror Devices TM in which
case there is a loss of warranty.
•
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
•
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet.
Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
•
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective
coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. For lens cleaning follow the
instructions precisely as stipulated in the projector manual.
•
Only use zoom lenses of the Barco TLD+ series. Using other lenses will damage the internal optics. For suitable fixed TLD+
lenses contact Barco or see Barco website.
•
Allowed ambient temperature range: t a= 0°C (32°F) to 40 °C (104 °F)
•
Rated humidity = 0% RH to 80% RH Non-condensed.
R5906112 UDX SERIES 24/05/2017
1. Safety
On servicing
•
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials
and risk of electric shock.
•
Refer all servicing to qualified service personnel.
•
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can
lead to permanent damage to the projector and cancellation of the warranty.
•
Remove all power from the projector and refer servicing to qualified service technicians under the following conditions:
-
When the power cord or plug is damaged or frayed.
-
If liquid has been spilled into the equipment.
-
If the product has been exposed to rain or water.
-
If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation.
-
If the product has been dropped or the cabinet has been damaged.
-
If the product exhibits a distinct change in performance, indicating a need for service.
•
Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement
parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may
void warranty.
•
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
Stacking/transporting UDX rental flight cases
1.3
•
Stack maximum 2 rental flight cases high. Never higher.
•
Surface on which flight case is standing must be level to ensure that the total load is evenly spread out among the four wheels.
The surface must also be able to support the load safely.
•
Before stacking or transporting flight cases, check the wheels and their fixation screws for wear or defects.
•
Before stacking or transporting flight cases, check that the four lock handles on each flight case are in good working order and
locked securely.
•
When stacked, make sure the wheels of the upper flight case are precisely positioned in the stacking dishes of the flight case
below.
•
Stacked flight cases may not be moved. Before stacking, the lower flight case must already be in its final resting position before
placing the second upon it.
•
Never stack loaded flight cases in a truck or other transport medium, unless each flight case is rigidly strapped tight.
•
In the event of a wheel breaking, flight cases must be rigidly strapped tight to prevent a stack collapsing.
•
Use an appropriate forklift to raise flight cases and take the necessary precautions to avoid personnel injury.
Product safety labels
Light beam related safety labels
Label image
Label description
Label location
Hazard RG3: not for household use symbol.
Hazard RG3: optical radiation warning symbol.
WARNING! DO NOT LOOK INTO THE LIGHT BEAM NO DIRECT EYE EXPOSURE TO
THE BEAM IS PERMITTED. RG3 IEC EN 62471–5:2015. CLASS 1 IEC EN 60825–1:2014.
HAZARD DISTANCE: CONSULT SAFETY MANUAL.
R5906112 UDX SERIES 24/05/2017
7
1. Safety
Label image
Label description
Label location
COMPLIES WITH 21 CFR 1040 EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS
AUTHORIZED BY VARIANCE NUMBER xxxx-x-xxxx DATED mm dd, yyyy RISK GROUP 3
LIP IEC 62471:2006.
警告! 勿观看光束 眼睛勿直接接触可允许暴露的光束 (RG3 IEC EN 62471-5:2015 CLASS 1
IEC EN 60825-1:2014) 危害距离:请参考 安全手册
DANGER ! NE PAS REGARDER LE FAISCEAU EVITER TOUTE EXPOSITION DIRECTE
DES YEUX AU FAISCEAU. RG3 IEC EN 62471-5:2015. CLASS 1 IEC EN 60825-1:2014.
DISTANCE DE SECURITE : CONSULTER LE MANUEL DE SECURITE.
1.4
High Brightness precautions: Hazard Distance (HD)
HD
Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the energy per surface
unit becomes lower than the applicable exposure limit on the cornea or on the skin. The light beam is considered (to
be) unsafe for exposure if the distance from a person to the light source is less than the HD.
Restriction Zone (RZ) based on the HD
The HD depends on the amount of lumens produced by the projector and the type of lens installed. See next chapter"HD in function
of modifying optics", page 11.
To protect untrained end users (as cinema visitors) the installation shall comply with the following installation requirements: Operators shall control access to the beam within the hazard distance or install the product at the height that will prevent spectators’ eyes
from being in the hazard distance. Radiation levels in excess of the limits will not be permitted at any point less than 2.0 meter (SH)
above any surface upon which persons other than operators, performers, or employees are permitted to stand or less than 1.0 meter
(SH) lateral separation from any place where such persons are permitted to be. In non-cinema environments where unrestrained
behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential
exposure, for example by an individual sitting on another individual’s shoulders, within the HD.
These values are minimum values and are based on the guidance provided in IEC 62471-5:2015 section 6.6.5.
The end user must understand the risk and apply protective measures based upon the hazard distance as indicated on the label and
in the user information. Installation method, barriers, detection system or other applicable control measure shall prevent hazardous
eye access to the radiation within the hazard distance.
For example, projectors that have a HD greater than 1 m and emit light into an uncontrolled area where persons may be present
should be positioned in accordance with “the fixed projector installation” parameters, resulting in a HD that does not extend into
the audience area unless the beam is at least 2.0 meter above the floor level. In non-cinema environments where unrestrained
behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential
exposure, for example by an individual sitting on another individual’s shoulders, within the HD. For example, a sufficiently large
separation height may be achieved by mounting the image projector on the ceiling or through the use of physical barriers.
For applications installed in the USA market the above limits do not apply. The relevant minimum separation height is 2.5 meter (8.2
ft) and the separation width is defined as 1.0 meter (3.3 ft) by the FDA CDRH.
RA
TH
TH
HD
SW
RZ
SW
RA
SH
RZ
PR
SH
HD
1m
SW
SW
(A) SIDE VIEW
(B) TOP VIEW
Image 1-1
A
Side view.
B
Top view.
RA Restricted Access location (boot area of projector).
PR Projector.
8
R5906112 UDX SERIES 24/05/2017
1. Safety
TH
RZ
SH
SW
Theater.
Restriction Zone in the theater.
Separation Height.
Separation Width.
Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and
the related hazard distance (HD). This shall be physically impossible by creating sufficient separation height or by placing barriers.
The minimum separation height takes into account the surface upon which persons other than operator, performers or employees
are permitted to stand.
On image 1-2 a typical setup is displayed. It must be verified if these minimum requirements are met. If required a restricted zone
(RZ) in the theater must be established. This can be done by using physical barrier, like a red rope as illustrated in image 1-2.
The restricted area sticker can be replaced by a sticker with only the symbol.
PR
RESTRICTED
AREA
RESTRICTED
AREA
Image 1-2
1.5
HD for fully enclosed projection systems
HD
Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the energy per surface
unit becomes lower than the applicable exposure limit on the cornea or on the skin. The light beam is considered (to
be) unsafe for exposure if the distance from a person to the light source is less than the HD.
Restriction Zone (RZ) based on the HD
The projector is also suitable for rear projection applications; projecting a beam onto a defuse coated projection screen. As displayed
in image 1-3 two areas should be considered: the restricted enclosed projection area (RA) and the observation area (TH).
R5906112 UDX SERIES 24/05/2017
9
RESTRICTED
AREA
sw
1. Safety
RA
RESTRICTED
AREA
sw
TH
RZ
HDDIFFUSE
PD
PR
sw
HD
sw
REFLECTION
Image 1-3
RA Restricted Access location (enclosed projection area).
PR Projector.
TH Theater (observation area).
RZ Restriction Zone.
PD Projection Distance.
SW Separation Width. Must be minimum 1 meter.
For this type of setup 3 different HD shall be considered:
•
HD as discussed in "High Brightness precautions: Hazard Distance (HD)", page 8 , relevant for intrabeam exposure.
•
HD reflection : the distance that has to be kept restrictive related to the reflected light from the rear projection screen.
•
HD diffuse : the relevant distance to be considered while observing the defuse surface of the rear projection screen.
As described in "High Brightness precautions: Hazard Distance (HD)", page 8 , it is mandatory to create a restricted zone within
the beam areas closer than any NOHD. In the enclosed projection area the combination of two restricted zones are relevant: The
restricted zone of the projected beam toward the screen; taking into account 1 meter Separation Width (SW) from the beam onward.
Combined with the restricted zone related to the rear reflection from the screen (HD reflection); also taking into account a 1 meter lateral
separation.
The HD reflection distance equals 25% of the difference between the determined HD distance and the projection distance to the rear
projection screen. To determine the HD distance for the used lens and projector model see graphs in chapter "HD in function of
modifying optics", page 11.
HD reflection = 25% (HD – PD)
The light emitted from the screen within the observation shall never exceed the RG2 exposure limit, determined at 10 cm. The
HD diffuse can be neglected if the measured light at the screen surface is below 5000 cd/m² or 15000 LUX.
10
R5906112 UDX SERIES 24/05/2017
1. Safety
1.6
HD in function of modifying optics
Hazard Distance
12,00
UDX 4K32
UDX U32
UDX W32
Hazard Distance [m]
10,00
8,00
UDX 4K22
UDX W22
6,00
4,00
11,1
11,5
10,7
9,9
10,3
9,5
9,1
8,3
8,7
7,9
7,5
6,7
7,1
6,3
5,9
5,5
4,7
5,1
4,3
3,9
3,5
2,7
3,1
2,3
2,0
1,7
1,3
0,9
0,00
0,5
2,00
Throw Ratio
Image 1-4
R5906112 UDX SERIES 24/05/2017
11
1. Safety
12
R5906112 UDX SERIES 24/05/2017
2. Remote Control Unit
2. REMOTE CONTROL UNIT
2.1
Remote control, Battery installation
Where to find the batteries for the remote control ?
The batteries are not placed in the remote control unit to avoid control operation in its package, resulting in a shorter battery life
time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your remote control,
install the batteries first.
How to install
1. Push the battery cover tab with the fingernail a little backwards (1) and pull, at the same time, the cover upwards (2).
1
2
Image 2-1
2. Insert the two AA size batteries, making sure the polarities match the + and - marks inside the battery compartment.
-
+
+
-
Image 2-2
3. Insert (1) both lower tabs of the battery cover in the gaps at the bottom of the remote control, and press (2) the cover until it clicks
in place.
2
-
+
+
-
1
Image 2-3
When replacing batteries, the broadcast address of the RCU will be reset to its default value ’0’.
R5906112 UDX SERIES 24/05/2017
13
2. Remote Control Unit
CAUTION: Replace with the correct battery type. Use two AA size batteries. There is a risk of explosion if the
battery is replaced with an incorrect type.
CAUTION: Replace the battery as explained above. There is a risk of explosion if the battery is incorrectly
installed.
2.2
Using the XLR connector of the RCU
Connecting a cable with the XLR connector will reset the broadcast address of the RCU to its default value ’0’.
How to use the XLR connector
1. Remove the XLR cover by pulling it backwards.
Image 2-4
2. Connect a cable with XLR plug into the XLR connector of the RCU.
3. Connect the other end of the cable with the XLR input of the projector.
2.3
Remote control, on/off button
Purpose of the remote control on/off button
The Pulse remote control unit has at the front side an on/off switch (reference 1 image 2-5). Switching off the remote control prevents
that unwanted commands are send due to an accidental key press. Furthermore, switching the RCU off will extend the battery life
time of the remote control.
To activate the remote control press the on/off button.
To deactivate the remote control press the on/off button again.
1
Image 2-5
14
R5906112 UDX SERIES 24/05/2017
3. Input & Communication
3. INPUT & COMMUNICATION
3.1
Introduction
General
The Input & Communication side of the projector consists of a local keypad, a communication panel, a venues & hospitality Input
(V&H) and a free input slots. The free input slot can be used for optional modules (e.g. Virtual & Augmented Reality Input (V&AR)).
1
2
3
4
5
6
Image 3-1
1
Local Keypad and touch panel
2
Optional antenna for WiFi connection
3
Optional antenna for GSM
4
Communication Panel
5
Venues & Hospitality Input (V&H)
6
Free input slot (here filled with the V&AR module)
3.2
Input source connections
Venues & Hospitality Input (V&H)
SDI IN
SDI IN/OUT
SEL
SYNC
SYNC
A
1
2
SYNC
SYNC
C
B
3
SEL
SEL
SEL
SEL
DP
D
4
5
SEL
HDMI
SYNC
6
SYNC
SEL
SEL
HDBT 1
7
SYNC
HDBT 2
SYNC
8
Image 3-2
1 Quad 3G SDI channel A Input
5 DisplayPort Input
2 Quad 3G SDI channel B Input
6 HDMI Input
3 Quad 3G SDI channel C Input
7 HDBaseT Input 1
4 Quad 3G SDI channel D Input
8 HDBaseT Input 2
The yellow LED lights up when valid input sync is detected.
The green LED lights up when the input is selected.
R5906112 UDX SERIES 24/05/2017
15
3. Input & Communication
Input specifications
HDMI
Up to 297 MHZ pixel clock
YCbCr 4:4:4
For future release
•
YCbCr 4:2:2 and YCbCr 4:2:0
•
3D support
•
Interlaced support
•
HDCP 1.4
•
HDCP 2.2
HDMI 1.4a
Support for ’Deep Color’ up to 12 bit per color
Audio
not supported
Video timings
640 x 480 @60 Hz
720 x 480 @60 Hz
720 x 576 @50 Hz
800 x 600 @60 Hz
1024 x 768 @60 Hz
1280 x 720 @50 Hz
1280 x 720 @60 Hz
1280 x 800 @60 Hz
1280 x 960 @60 Hz
1280 x 1024 @60 Hz
1400 x 1050 @60 Hz
1600 x 1200 @60 Hz
1920 x 1080 @24 Hz
1920 x 1080 @25 Hz
1920 x 1080 @30 Hz
1920 x 1080 @50 Hz
1920 x 1080 @60 Hz
1920 x 1200 @50 Hz
1920 x 1200 @60 Hz
2048 x 1080 @24 Hz
2048 x 1080 @25 Hz
2048 x 1080 @30 Hz
2048 x 1080 @48 Hz
2048 x 1080 @50 Hz
2048 x 1080 @60 Hz
2560 x 1600 @50 Hz
2560 x 1600 @60 Hz
3840 x 2160 @24 Hz
3840 x 2160 @25 Hz
3840 x 2160 @30 Hz
3840 x 2160 @50 Hz
3840 x 2160 @60 Hz
4096 x 2160 @24 Hz
16
R5906112 UDX SERIES 24/05/2017
3. Input & Communication
HDMI
4096 x 2160 @25 Hz
4096 x 2160 @30 Hz
4096 x 2160 @50 Hz
4096 x 2160 @60 Hz
HDBase-T
25 – 297 MHz pixel clock
Colors
•
YCbCr 4:2:2
•
YCbCr 4:4:4
•
Color 24 bpp
•
Color 30 bpp
•
Color 36 bpp
For future release
Audio
•
3D support
•
Interlaced support
•
HDCP 1.4
not supported
Video timings
640 x 480 @60 Hz
720 x 480 @60 Hz
720 x 576 @50 Hz
800 x 600 @60 Hz
1024 x 768 @60 Hz
1280 x 720 @50 Hz
1280 x 720 @60 Hz
1280 x 800 @60 Hz
1280 x 1024 @60 Hz
1400 x 1050 @60 Hz
1600 x 1200 @60 Hz
1920 x 1080 @24 Hz
1920 x 1080 @25 Hz
1920 x 1080 @30 Hz
1920 x 1080 @50 Hz
1920 x 1080 @60 Hz
1920 x 1200 @50 Hz
1920 x 1200 @60 Hz
2048 x 1080 @24 Hz
2048 x 1080 @25 Hz
2048 x 1080 @30 Hz
2048 x 1080 @48 Hz
2048 x 1080 @50 Hz
2048 x 1080 @60 Hz
2560 x 1600 @50 Hz
2560 x 1600 @60 Hz
3840 x 2160 @24 Hz
3840 x 2160 @25 Hz
R5906112 UDX SERIES 24/05/2017
17
3. Input & Communication
HDBase-T
3840 x 2160 @30 Hz
4096 x 2160 @24 Hz
4096 x 2160 @25 Hz
4096 x 2160 @30 Hz
SDI
3G SDI follows the SMPTE 425M standard Level A
HD-SDI follows the SMPTE 292M standard
Color space
YCbCr
RGB : future release
Color depth
10 bpc
12 bpc : future release
Chroma sampling
4:2:2 only
Audio support
not supported
3D support
For future release
4:2:0 and 4:4:4 : future release
•
Interlaced support
•
Segmented frame support
Video timings
Progressive
Type
Port type
Format
HD-SDI
Single link
1280 x 720 @24 Hz
HD-SDI
Single link
1280 x 720 @25 Hz
HD-SDI
Single link
1280 x 720 @30 Hz
HD-SDI
Single link
1280 x 720 @50 Hz
HD-SDI
Single link
1280 x 720 @60 Hz
HD-SDI
Single link
1920 x 1080 @24 Hz
HD-SDI
Single link
1920 x 1080 @25 Hz
HD-SDI
Single link
1920 x 1080 @30 Hz
3G-SDI Level A
Single link
1920 x 1080 @50 Hz
3G-SDI Level A
Single link
1920 x 1080 @60 Hz
3G-SDI Level A
Single link
2048 x 1080 @50 Hz
3G-SDI Level A
Single link
2048 x 1080 @60 Hz
3G-SDI “BarcoLink”
Single link
1920 x 1200 @50 Hz
3G-SDI “BarcoLink”
Single link
1920 x 1200 @59.94 Hz
3G-SDI “BarcoLink”
Single link
1920 x 1200 @60 Hz
DisplayPort
Up to 600 MHz pixel clock
Colors
3D support
18
•
YCbCr 4:4:4
•
YCbCr 4:2:2
Field sequential 3D (active 3D)
R5906112 UDX SERIES 24/05/2017
3. Input & Communication
DisplayPort
For future release:
•
Passive 3D support
•
Interlaced support
•
HDCP 1.4
Audio
not supported
DP 1.2
Support for ’Deep Color’ up to 12 bit per color
Bitrate Support
•
Reduced Bit Rate (RBR)
•
High Bit Rate (HBR)
•
High Bit Rate 2 (HBR2)
Video timings
640 x 480 @60 Hz
800 x 600 @60 Hz
960 x 2160 @120 Hz
960 x 2400 @120 Hz
1024 x 768 @60 Hz
1024 x 2160 @120 Hz
1280 x 800 @60 Hz
1280 x 960 @60 Hz
1280 x 1024 @60 Hz
1400 x 1050 @60 Hz
1600 x 1200 @60 Hz
1920 x 1080 @24 Hz
1920 x 1080 @30 Hz
1920 x 1080 @50 Hz
1920 x 1080 @60 Hz
1920 x 1200 @50 Hz
1920 x 1200 @60 Hz
1920 x 1200 @120 Hz
1920 x 2160 @60 Hz
1920 x 2160 @120 Hz
2048 x 1080 @24 Hz
2048 x 1080 @25 Hz
2048 x 1080 @30 Hz
2048 x 1080 @48 Hz
2048 x 1080 @50 Hz
2048 x 1080 @60 Hz
2048 x 1080 @120 Hz
2560 x 1600 @50 Hz
2560 x 1600 @60 Hz
3840 x 2160 @24 Hz
3840 x 2160 @25 Hz
3840 x 2160 @30 Hz
3840 x 2160 @50 Hz
3840 x 2160 @60 Hz
R5906112 UDX SERIES 24/05/2017
19
3. Input & Communication
DisplayPort
3840 x 2400 @50 Hz
3840 x 2400 @60 Hz
4096 x 2160 @24 Hz
4096 x 2160 @30 Hz
4096 x 2160 @50 Hz
4096 x 2160 @60 Hz
3D Support
1280 x 720 @50 Hz
1280 x 720 @60 Hz
1920 x 1080 @50 Hz
4096 x 2160 @24 Hz
CAUTION: In order to display high resolution images (ex.: 3840X2160@60Hz) via the DP1.2 input, the quality
of the cable must be adequate, in addition the length of the cable can also influence the performance. In case
there is an issue with one of these criteria the automatic link-training initiated by the DP-standard may decide
to switch to a lower resolution.
CAUTION:
The HDBaseT inputs can bridge a distance of 100 m but is sensitive to radiated electromagnetic
interference: radiated electromagnetic interference (e.g. from GSM or switching inductive or capacitive loads)
within the limits of electromagnetic compatibility requirements of 3 V/m can cause random flashes or temporary loss of the projected image.
As such, shielded CAT-6 cables with metal RJ-45 connectors are recommended; choose cable length no longer
than required and route HDBT cable optimally screened from possible sources of electromagnetic emission.
Virtual & Augmented Reality Input (V&AR) (Optional)
SEL
DP A
DP B
SYNC
1
SEL
SEL
DP C
SYNC
2
3
SEL
DP D
SYNC
SYNC
4
Image 3-3
1 Quad DisplayPort channel A Input
3 Quad DisplayPort channel C Input
2 Quad DisplayPort channel B Input
4 Quad DisplayPort channel D Input
The yellow LED lights up when valid input sync is detected.
The green LED lights up when the input is selected.
Input specifications
All inputs are DisplayPort 1.2 .
DP
Up to 600 MHz pixel clock
YCbCr 4:4:4
For future release
Audio
20
•
YCbCr 4:2:2 and YCbCr 4:2:0
•
3D support
•
Interlaced support
•
HDCP 1.4
not supported
R5906112 UDX SERIES 24/05/2017
3. Input & Communication
DP
DP 1.2
Support for ’Deep Color’ up to 12 bit per color
Video timings
640 x 480 @60 Hz
720 x 480 @60 Hz
800 x 600 @60 Hz
1024 x 768 @60 Hz
1280 x 720 @50 Hz
1280 x 720 @60 Hz
1280 x 960 @60 Hz
1280 x 1024 @60 Hz
1400 x 1050 @60 Hz
1920 x 1080 @24 Hz
1920 x 1080 @30 Hz
1920 x 1080 @50 Hz
1920 x 1080 @60 Hz
1920 x 2160 @60 Hz
2560 x 1600 @60 Hz
3840 x 2160 @24 Hz
3840 x 2160 @30 Hz
3840 x 2160 @60 Hz
4096 x 2160 @24 Hz
4096 x 2160 @30 Hz
3.3
Communication connections
Communication Panel
1
2
3
4
5
6
7
8
9
10
11
12
13
Image 3-4
1 WIFI antenna for wireless IP (optional)
8 RS232 for serial communication
2 12V 1A output
9 Sync Out 3D
3 Firmware update / USB backup custom settings
10 Sync In 3D
4 10/100 base-T for external control over IP and Art-Net
11 Status lights
5 DMX interface input
12 IR receive sensor
6 DMX interface output
13 GSM antenna input (optional)
7 XLR input for wired projector control
12V output
12 V output, maximum 1A, available when projector is not in stand by.
R5906112 UDX SERIES 24/05/2017
21
3. Input & Communication
DMX interface
DMX is used as communication bus between different devices in the light technic. Each device has an input and an output, so that
the bus can be looped between the different devices. According the standard a five wire cable with XLR connector is used.
You can use the DMX input port to connect a DMX device (DMX console) to the projector. This way you can control the projector
from that DMX device (console). The DMX output port can be connected with the next device in the loop.
Pin
Description
1
Earth
2
Cold
3
Hot
4
Return - (or not used)
5
Return + (or not used)
DMX
DMX-512 Lighting protocol over RS-485 interface. Carries information of 512 channels from a lighting controller to
lighting devices. Standardized by USITT.
RS232/RS422 input
The communication interface of the UDX supports RS232 and RS422 serial communication on two different types of input connectors, a Sub-D connector and an USB connector acting as RS input when connected to an USB input of a PC.
You can use the RS232/RS422 input to connect a local PC to your UDX. By this way you can configure and control your UDX from
your local PC.
Advantages of using RS232/RS422 serial communication:
•
easy adjustment of the projector via PC (or MAC).
•
allow storage of multiple projector configurations and set ups.
•
wide range of control possibilities.
•
address range from 0 to 255.
•
sending data to the projector (update).
•
copying data from the projector (backup).
RS232/422 input (Sub-D) port
Pin
Description
1
DCD : Data Carrier Detect
2
RXD- : Receive Data
3
TXD- : Transmitted Data
4
DTR : Data Terminal Ready [RS232]
TXD+ : Transmitted Data [RS422]
5
GND : Ground
6
DSR : Data Set Ready [RS232]
RXD+ : Received Data [RS422]
7
— (not connected) —
8
CTS : Clear To Send
9
RI : Ring Indicator
RS232
An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the communication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for
relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard
with a set number of conductors, data rate, word length and type of connector to be used. The standard specifies component connection standards with regard to computer interface. It is also called RS-232-C, which is the third version
of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical ’0’ is > + 3V, Logical ’1’ is < 3V. The range between -3V and +3V is the transition zone.
22
R5906112 UDX SERIES 24/05/2017
3. Input & Communication
RS422
An EIA serial digital interface standard that specifies the electrical characteristics of balanced (differential) voltage,
digital interface circuits. This standard is usable over longer distances than RS-232. This signal governs the asynchronous transmission of computer data at speeds of up to 920,000 bits per second. It is also used as the serial port
standard for Macintosh computers. When the difference between the 2 lines is < - 0.2V that equals with a logical ’0’.
When the difference is > +0.2V that equals to a logical ’1’..
USB port
The communication interface is equipped with a master USB port, type “A” connector. This USB port will simplify the service procedures for software updates or for taking backup files from the projector without network connection. An USB-stick is plugged into
the USB port and files can be transferred from or to the projector using the local or remote control unit. Note that the USB-stick has
to be Linux FAT16 compatible.
3.4
LED and Button indication chart
Button Backlight Status
Button
Color status
Description
Standby button
Blinking WHITE (slow)
Projector starts up (booting)
Blinking WHITE (fast)
Firmware upgrade
Solid WHITE
Projector is in Standby mode
Blinking BLUE
Projector goes to ON mode
Solid BLUE
Projector is ON
Blinking RED
Error condition
Off (no color)
Solid WHITE
Projector is OFF, starts up, or is in Standby
mode.
Projector is ON, shutter is open
Solid RED
Projector is ON, shutter is closed
LED
Color status
Description
PWR (power LED)
Off
Projector powers up
RED
Projector is in Standby
ORANGE
Projector is Ready
GREEN
Projector is on
Off
Light source is off
RED
No light source detected
ORANGE
Light source is on in ECO mode
GREEN
Light source is on in normal mode
GREEN-ORANGE
Light source is on in CLO mode
Shutter button
LED Status
LIGHT (Illumination LED)
R5906112 UDX SERIES 24/05/2017
23
3. Input & Communication
LED
Color status
Description
ERR (error LED)
Off
No error
RED toggles on/off
Error
ORANGE toggles on/off
Warning
RED
IR signal received
GREEN
IR signal acknowledged
IR
24
R5906112 UDX SERIES 24/05/2017
4. Getting Started
4. GETTING STARTED
How controlling the projector ?
The projector can be controlled by the local keypad, by the remote control unit or by browser application.
Location of the local keypad ?
The local keypad is located on the input side of the projector.
Remote control functions.
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This
remote control is used for source selection, control, adaptation and set up.
Other functions of the remote control are :
•
switching between stand by and operational mode.
•
switching to "pause" (blanked picture, full power for immediate restarting)
•
direct access to all connected sources.
Overview
4.1
•
Functionality overview
•
Power on projector
•
Switching to standby
•
Power off projector
•
Using the RCU
•
Projector Address
•
Quick setup via Direct access
Functionality overview
Local Keypad overview
1
1 Menu Selection.
2
3
4
5
6
2 Menu Activation, OK button
3 OSD On/Off.
4 Menu Back.
5 Power On/Off.
6 Touch Panel On/Off.
7 Input Selection.
8 Shutter Open/Close.
11
10
9
8
7
9 Test Patterns.
10 Lens Menu.
11 Touch Panel.
The Keypad gives direct access to several functions, in addition to access to the menu system.
The keypad has a back light that can be switched on and off manually. The light turns off automatically after a preselected time.
The keys are equipped with white and blue backlit LEDs. Power button is equipped with white, blue and red backlit. The LEDs are
controlled according to the features available.
R5906112 UDX SERIES 24/05/2017
25
4. Getting Started
Remote Control Unit buttons
1
1 Button pressed indicator.
14 Backspace (while entering
values)
2 Shutter Open.
15 XLR connector.
3 Shutter Close.
16 Decimal mark (while entering
values)
2
24
3
23
4
22
5
21
6
20
4 Touch Panel On/Off.
17 Macro button.
7
19
5 OSD On/Off.
18 Menu Back.
8
18
6 Lens Zoom.
19 Default button.
10
7 Lens Shift.
20 Lens Focus.
11
8 Menu Activation.
21 Color On/Off.
9 Menu Selection, OK button.
22 Test Patterns.
9
12
17
13
14
16
10 Menu Navigation.
23 Power On.
11 Input Selection.
24 Power Off.
12 Address button.
25 Stereo Jack.
13 Numeric buttons.
26 RCU On/Off.
15
25
26
The projector remote control is a full feature wireless remote control, powered by two (2) standard AA batteries. The battery compartment is on the back side of the remote control.
The remote control is backlit for use in dark environments. It also has an XLR connector for wired connection to the projector. When
the wire is connected, the IR beam is switched off.
LCD panel
The LCD panel has two main functions:
1.
Showing the menus and adjustment information. and also a mirror of the OSD, (On Screen Display) described in User Interface
when this is enabled.
2.
Information regarding the status of the projector showing this data:
-
Projector status
-
Network address
-
Active source
-
Current firmware version
-
Operation Data
-
Active functions (Enabled Functions).
Toggle between the two indications by using the Menu button on the keypad, or on the remote control
The LCD Display will fade out 30 seconds after the last key operation.
4.2
Power on projector
How to power on
1. Press the mains switch at the side of the projector to switch on this projector.
26
R5906112 UDX SERIES 24/05/2017
4. Getting Started
Image 4-1
Mains switch
-
When ’0’ is pressed, the projector is switched off.
-
When ’I’ is pressed, the projector is switched on.
The projector starts up to standby mode. The Power on/off button will blink until standby mode is achieved. Once in standby
mode, the Power on/off button will be lit WHITE, but the display will be off.
2. Press the Power on/off button on the projector, or the Power On button on the remote control.
The projector will continue to power on mode. The Power on/off button will blink until the projector is ready. Once the projector
is ready, the Power button will be lit BLUE.
The start up screen is displayed on the touch panel and when fully started up, it changes to the overview screen.
1
2
Image 4-2
The current mains input voltage is indicated on the voltmeter just above the power switch.
The background image of the startup screen and info screens can be changed with Projector Toolset with an
installed UDX plug-in.
Status overview
Once the projector is started, press Status to get an overview of parameters such as :
•
Device serial number and article number
•
Current firmware version and model name
•
Current illumination (in percentage)
•
Projector runtime in hours
•
Uptime in hours
•
Chosen source
•
Current resolution and refresh rate
•
Chosen communication method and IP address (if connected)
•
Active functions
R5906112 UDX SERIES 24/05/2017
27
4. Getting Started
Starting image projection
1. Make sure the available sources are connected to the appropriate input ports.
Tip:
If properly connected, the “SYNC” LED will lit up ORANGE.
2. Press the Input Selection button on the keypad or on the remote control until:
-
the LED of the selected source (the “SEL” LED) lit up GREEN, and
-
the image of the selected source is projected.
1
2
Image 4-3
4.3
Switching to standby
How to switch to standby
1. Press and hold the Power on/off button for 3 seconds on the local keypad, or press the Power Off button on the remote control.
The projector goes to standby mode. The after-cooling cycle will start (about 30 seconds). During this period the Power on/off
button will blink. Once the after-cooling cycle has ended, the projector will be in standby mode and the Power on/off button will
be lit WHITE.
3s
30 s
Image 4-4
4.4
Power off projector
CAUTION:
This procedure assumes the projector is in standby mode.
How to power off
1. Switch off the projector with the mains switch. ’0’ must be pressed.
28
R5906112 UDX SERIES 24/05/2017
4. Getting Started
Image 4-5
2. Unplug the power cord from the projector.
4.5
Using the RCU
Pointing to the reflective screen
1. Point the front of the RCU to the reflective screen surface.
Image 4-6
IR control via reflective screen
Hardwired to the XLR input
1. Plug one end of the remote cable in the connector on the bottom of the RCU.
2. Plug the other end in the big connector on the communication interface of the projector, labelled Remote CTRL.
Note: Plugging the remote control will switch the broadcast address of the remote control to the default value ’0’. This is the
only broadcast address that will work when hardwired. If you want to change the broadcast address after disconnecting
the remote control, see "Projector Address", page 30.
Pointing directly to the IR sensor
When using the wireless remote control, make sure you are within the effective operating distance (30 m, 100 ft in a straight line).
The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote
control unit and the projector IR sensor.
R5906112 UDX SERIES 24/05/2017
29
4. Getting Started
45°
45°
45°
45°
45°
45°
Image 4-7
RCU to one of the IR sensors
4.6
Projector Address
Projector address
Address installed in the projector to be individually controlled.
Broadcast address
Projector will always execute the command coming from a RCU programmed with that broadcast address.
4.6.1
Controlling the projector
Why a projector address?
As more than one projector can be installed in a room, each projector should be separately addressable with an RCU or computer.
Therefore each projector has its own address.
Set up an individual Projector Address
The set up of a projector address can be done via the software.
Projector controlling
Every projector requires an individual address between 0 and 255.
When the address is set, the projector can be controlled now:
•
with the RCU: only for addresses between 0 and 31.
•
with a computer: for any address between 0 and 255.
Broadcast Address
Every projector has a broadcast (common) address ’0’ or ’1’. The default address is ’0’.
The choice between ’0’ and ’1’ can be selected in the GUI: “System Settings” → “Communication” →“IR Control “.
Placing new batteries in the remote control or plugging the remote to a projector via XLR cable will automatically reset the address back to its default value ’0’.
30
R5906112 UDX SERIES 24/05/2017
4. Getting Started
4.6.2
Displaying and Programming addresses into the RCU
Displaying the Projector Address on the Screen.
1. Press the Address button to see the projector address (proximately 2 seconds).
The projector’s address is displayed on the LCD status screen.
How to Program an Address into the RCU?
1. Press the Address button until the Button pressed indicator lights up continuously (proximately 5 seconds).
2. Enter the address with the digit buttons within the time the indicator lights up (also proximately 5 seconds).
Note: That address can be any value between 0 and 31.
Tip:
A few examples:
To enter address 3, press "3" digit button on the RCU to set the RCU’s address to 3 and wait until the button pressed
indicator is out. Alternatively, you can also press “0” and “3”. This way, he button pressed indicator goes out immediately.
To enter address 31, then press “3” and “1” on the digit button on the RCU and the button pressed indicator goes out
immediately.
4.7
Quick setup via Direct access
Quick source selection
1. Press the Input button on the remote control or local keypad.
I
I
Image 4-8
The source selection menu opens.
Image 4-9
Input selection
2. Use the arrow keys to select the desired source.
R5906112 UDX SERIES 24/05/2017
31
4. Getting Started
Quick test pattern selection
1. Press the Test pattern button on the remote control or local keypad.
P
P
Image 4-10
A first test pattern will be displayed.
2. Press as may times on that button until the desired pattern is displayed
32
R5906112 UDX SERIES 24/05/2017
5. Graphic User Interface (GUI)
5. GRAPHIC USER INTERFACE (GUI)
Overview
5.1
•
Overview
•
Navigation
•
Test Patterns
Overview
GUI - Main Menu overview
The projector on screen display (OSD) is the primary user interface (UI). From here, you can review and adjust all projector and
display settings.
The OSD interface uses tabs to display the main menu. Each main menu contains submenus.
The OSD can be disabled by pressing the OSD on/off button.
Image 5-1
Home menu
The projector’s software platform uses access levels what each user can do. A standard user has access to all projector functionality.
A certified service technician has also access to the service menu. This menu is password protected.
5.2
Navigation
Navigation via the RCU or local keypad
Navigating the OSD can be done using the remote control or the local keypad.
1
2
3
4
3
2
1
4
Image 5-2
To start up the menu structure, press MENU (1).
R5906112 UDX SERIES 24/05/2017
33
5. Graphic User Interface (GUI)
Use the arrow keys (Menu Navigation buttons) to navigate to the desired menu item (2). The background color changes to light
blue.
Press the Menu Selection button (center key of the arrow keys), also called OK button, to activate that item and to jump one level
deeper (3).
Use the numeral keys to enter values, or use the arrow keys to move the bar scale up or down.
Press the Back button to go up one level (4).
Image 5-3
Home menu
Remark: a blue slider bar on the right side of the window means that there are more items to show than those currently displayed.
Define values
Menu settings are displayed using check boxes, bar scale sliders, and drop-down lists.
To set a value:
•
Press OK to select or deselect a checkbox (turn a function ON or OFF).
•
Use the arrow keys to move the bar scale slider up or down on the value line. For a bar scale 0-9, each step will equal 10% of
the total value.
•
To enter the value as a direct number, press OK, input the digit(s), and then press OK again to execute and exit cursor mode
e.g. OK 79 OK.
Within an input field, use the * button as backspace button to remove an entered digit. Use the # button to enter a dot (.).
Changes to values are implemented dynamically.
To enter values with the local keyboard, use the arrow keys to select the first digit, press OK. Select the second digit and press OK.
Continue until all digits are entered. Close the action by selecting the enter (↵) button and press OK. Select the backspace button
and press OK to remove the last entered digit.
Menu memory
The OSD menu remembers the last selected sub-item as long as the projector is running. The menu memory is reset when restarting
the projector from standby.
5.3
Test Patterns
How to use test patterns
1. In the main menu, select Test Patterns.
Or,
Push the Test Patterns button on the RC or on the local keypad.
Image 5-4
Main menu, Test Patterns
2. In the Test Patterns menu, select either Internal, or Output test patterns.
3. In the chosen submenu, select the desired test pattern from the list.
You can select one of the following Internal test patterns:
34
R5906112 UDX SERIES 24/05/2017
5. Graphic User Interface (GUI)
-
Color bars
-
Checker board
-
Blue / Green / Red / White
-
Convergence
-
Focus
-
Aspect
-
Cross hatch
-
Mono scope
You can select one of the following Output test patterns:
-
Vertical / diagonal lines
-
Step bar
-
Blemish zone
-
Checkerboard
-
Color bars
-
Convergence
-
FIP
-
Full screen black / white / blue / green / red / cyan / magenta / yellow
-
Grid
-
Vertical Ramp
-
Horizontal Ramp
-
MTF
4. To turn the test pattern off, return to the previous menu.
R5906112 UDX SERIES 24/05/2017
35
5. Graphic User Interface (GUI)
36
R5906112 UDX SERIES 24/05/2017
6. GUI – Source
6. GUI – SOURCE
About the Source menu
This menu is used to select, review and configure sources into the projector.
Overview of features
6.1
•
Source Selection
•
Connector Settings
Source Selection
How to select?
1. Press Menu to activate the menus and select Source.
Image 6-1
Select Source
2. Press OK.
The Select Source menu is displayed with the actual available sources filled out.
Image 6-2
Input selection
3. Select the desired input.
6.2
Connector Settings
How to configure the connector
1. Press Menu to activate the menus and select Source.
Image 6-3
Select Source
2. Press OK.
R5906112 UDX SERIES 24/05/2017
37
6. GUI – Source
The Select Source menu is displayed with the actual available sources filled out.
3. Scroll down to the bottom of the list and select Connector Settings.
Image 6-4
The available sources are displayed.
Image 6-5
Select source
4. Select the desired connector.
The Connector Settings menu for this connector will be displayed. All default values are Auto.
Image 6-6
5. To apply a limit on the used color space, select one of the other values in Color space.
6. To apply a limit on the used signal range, select one of the other ranges in Signal Range.
38
R5906112 UDX SERIES 24/05/2017
7. GUI – Image
7. GUI – IMAGE
Overview of features
•
7.1
Setting image levels manually
•
P7 Realcolor
•
Setting the output resolution
Setting image levels manually
Purpose
Contrast: Change the contrast of the complete output signal (main and PiP window together) of the projected image.
Brightness: Change the brightness of the complete output signal (main and PiP window together) of the projected image.
Saturation: Change the saturation of the complete output signal (main and PiP window together) of the projected image.
How to set up Contrast
1. In the main menu, select Image → Contrast.
Image 7-1
Image menu — Contrast
2. Use the ◄ or ► key to change the contrast enhancement until the desired value is reached (adjustable between 0 and 2).
Image 7-2
Contrast slider
3. Use the ▲ or ▼ key to select Saturation or Brightness.
Or,
go to Home - Image and select Saturation or Brightness.
How to set up Brightness Level
1. In the main menu, select Image → Brightness.
Image 7-3
Image menu — Brightness
R5906112 UDX SERIES 24/05/2017
39
7. GUI – Image
2. Use the ◄ or ► key to change the brightness until the desired value is reached (adjustable between –1 and 1).
Image 7-4
Brightness slider
3. Use the ▲ or ▼ key to select Contrast or Saturation.
Or,
go to Home - Image and select Contrast or Saturation.
How to set up Saturation Level
1. In the main menu, select Image → Saturation.
Image 7-5
Image menu — Saturation
2. Use the ◄ or ► key to change the saturation until the desired value is reached (adjustable between -1 and 1).
Image 7-6
Saturation slider
3. Use the ▲ or ▼ key to select Brightness or Contrast.
Or,
go to Home - Image and select Brightness or Contrast.
7.2
P7 Realcolor
Purpose
When blending images from multiple projectors, the measured color coordination of each projector can be altered to a desired
common level. This so that the projected colors are identical over all projectors used.
40
R5906112 UDX SERIES 24/05/2017
7. GUI – Image
How to set the P7 desired values
1. In the main menu, select Image → Advanced → P7 Realcolor.
Image 7-7
Advanced menu — P7 Realcolor
The P7 menu is displayed.
Image 7-8
P7 Realcolor menu
2. Select the desired Mode. Choose one of the following:
-
Native: Default mode, with default values. All other options in the P7 menu are disabled.
-
Custom RGB: 3–point color configuration. In RGB mode, the C, M and Y coordinates will be calculated automatically based
on the R, G and B coordinates.
-
Custom RGBCMY: 6–point color configuration (both RGB and CMY). In RGBCMY mode, each color can be given a specific
coordinate within the measured color triangle.
-
Custom WHITE: Configure only the White temperature.
3. Define the coordinates for each available color.
Click on a coordinate value and select the current value. Enter the desired value with the numeric keys.
Note: You can only pick coordinates within the measured color triangle.
4. For Custom White, click on White point and choose one of the following:
-
Coordinates: Configure the white point via specific coordinates. The white point is specified using an x, y coordinate in the
CIE 1931 Chart.
-
Temperature: Configure the white point via a color temperature slider. The white point is specified on a Kelvin scale between
3200K and 13000K tracking along the black body curve.
You can reset all coordinates to the default values (to native) by selecting Reset modes to native. Press OK
button to reset.
7.3
Setting the output resolution
This menu is only available on the 4k models, with an actuator included.
How to choose the output resolution
1. In the main menu, select Image → Advanced → Output resolution.
R5906112 UDX SERIES 24/05/2017
41
7. GUI – Image
Image 7-9
Advanced menu — Output resolution
The current active output resolution is indicated at the bottom of the selection button.
2. Select the desired output resolution.
Possible resolutions:
-
4K UHD: 4K images, using the actuator.
-
WQXGA: 2K images. In this mode, the actuator is disabled.
Image 7-10
Output resolution
42
R5906112 UDX SERIES 24/05/2017
8. GUI – Installation
8. GUI – INSTALLATION
Overview of features
•
Configuring the lens, shift
•
Orientation
•
Warping
•
Blending
•
Laser illumination
8.1
Configuring the lens, shift
What can be done?
The image can be shifted by using the vertical and horizontal lens shift.
Vertical and Horizontal Shift
1. To change the position of the projected image, select Installation → Lens → Shift.
Image 8-1
Lens menu, Lens shift
2. Use the ▲ or ▼ key to shift the lens (image) in vertical direction.
Use the ◄ or ► key to shift the lens (image) in horizontal direction.
Image 8-2
Shift adjustment
8.2
Orientation
What can be done?
The way of physical installation of the projector can be defined to the projector.
The following installation are possible:
•
front/table
•
front/ceiling
•
rear/table
•
rear/ceiling
R5906112 UDX SERIES 24/05/2017
43
8. GUI – Installation
How to set the correct orientation
1. In the main menu, select Installation → Orientation.
Image 8-3
Installation menu, Orientation
The Orientation menu is displayed.
Image 8-4
Orientation menu
2. Use the ▲ or ▼ key to select the desired mounting position and press OK button to activate.
Use the ▲ or ▼ key to select the desired projection position and press OK button to activate.
8.3
8.3.1
Warping
About warping
Overview
Image warping is the process of digitally manipulating an image to compensate for the distortion of the screen. Consequently, it can
also be used to generate an image with irregular shape.
While an image can be transformed in various ways, pure warping doesn’t affect the colors.
8.3.2
Warping – On/Off
About warping on/off
By toggling between on and off the warping functionality can be enabled or disabled.
How to toggle
1. In the main menu, select Installation → Warp.
Image 8-5
Installation menu, Warp
2. In the Warp menu, click Warp to toggle between On and Off.
44
R5906112 UDX SERIES 24/05/2017
8. GUI – Installation
Image 8-6
8.3.3
Image 8-7
Warping – Screen Size
About (Warp) Screen Size adjustment
If the used source aspect ratio is different than the projector aspect ratio, e.g. source is 16:9 and projector is 16:10, then black bars
will be projected. In the example case a black bar on top and bottom of the image will be projected. The warp area contains not
only the image information but also the black bars. If we want to position e.g. the active left top corner exactly on the screen using
4 corner warp, then it is very hard to do that as we are moving the black left top corner and we do not have control over the exact
position of image left top corner. By moving the outline of the warp screen size to the active image information, the corner points of
the warp area are now exactly on the corner points of the active image information and makes warping much easier.
Image 8-8
Warp outline example
How to adjust the image?
1. In the main menu, select Installation → Warp → Screen Size.
Image 8-9
Warp Menu, Screen Size
The Screen Size menu is displayed.
R5906112 UDX SERIES 24/05/2017
45
8. GUI – Installation
Image 8-10
Screen size
2. Select either Screen width or Screen height.
3. Set the new value to shrink either the width or height of the warp outline so that the outline is equal with the active source.
Tip:
A red border will be projected along with the current image. The border is a visual tool, showing the result of the adjusted
outline.
4. Click Apply.
8.3.4
Warping – 4 corners adjustment
About 4 Corners adjustment
4 corner adjustment is typically used when the mechanical installation of the projector prevents it from pointing perpendicularly at
the screen. For example, you can overshoot the screen and use 4 corner adjustment to pull your projected image corners back into
the screen.
Some examples:
Image 8-11
4 corner adjustment
How to adjust the image?
1. In the main menu, select Installation → Warp → 4Corners.
Image 8-12
Warp menu, 4Corners
46
R5906112 UDX SERIES 24/05/2017
8. GUI – Installation
The 4Corners menu is displayed.
Image 8-13
4Corners Warping
2. To enable 4 corners, make sure the 4 corners slider is set to On.
The slider is enabled when set to the right and when it is colored blue.
3. To set warping on one or more of the four corners, select one of the four corners.
4. Set the desired X and Y coordinates for this corner, using the arrow keys.
Tip:
A red border corner will be projected along with the current image. The border is a visual aid, showing the result of the
warped corners.
5. Repeat from step 3 for each corner, until all corners are warped in the desired position.
To reset the 4 corner adjustments, select Reset and press the OK button.
8.3.5
Warping – Bow
About bow adjustment
A bow distortion can be adjusted so that a normal image is displayed. Positive adjustments introduce more outside bow distortion.
Negative adjustments introduce more inside bow distortion.
Image 8-14
Bow distortion
How to adjust
1. In the main menu, select Installation → Warp.
R5906112 UDX SERIES 24/05/2017
47
8. GUI – Installation
Image 8-15
Installation menu, Warp
2. In the Warp menu, select Bow.
Image 8-16
Warp menu, Bow
A check symbol at the bottom right corner indicates that the bow function is activated.
3. To enable Bow correction, make sure the Bow slider is set to On.
The slider is enabled when set to the right and when it is colored blue.
Image 8-17
Bow adjustment
4. To enable a symmetric adjustment, make sure the Symmetric slider is set to On.
The slider is enabled when set to the right and when it is colored blue.
5. Select an adjustment point and use the arrow keys to adjust.
When selecting a mid point of an edge, the bow angle can be adjusted.
When selecting a corner point, the linearity can be adjusted.
To reset the bow adjustments, select Reset and press the OK button.
8.4
Blending
About Blending
Blending is used in multi channel installation to have a seamless transition between the channels. Image blending gives the appearance of a single view, thus achieving realistic immersion for the majority of wide screen applications.
The principle is that the light intensity in the blend zone from each projector will be adjusted individually, so that the rendering on the
screen are perceived as from one projector.
From the start (offset) position, you can blend zone size per edge (left, top, right, bottom). For each edge there will be a drop-off
curve for the blend zone.
48
R5906112 UDX SERIES 24/05/2017
8. GUI – Installation
8.4.1
Blend Zones
About offset and blending width or height
Offset is used to clip the image. The larger the offset value, the more the image is masked (by black bar) at the corresponding side.
E.g. Top offset of 100 will blank the top 100 lines.
Height or width is used to create a blending zone with a smooth brightness drop off. This is used to compensate for the double
brightness in overlap areas. The value is the size of the blended area in pixels.
How to adjust blend zones?
1. In the main menu, select Installation → Blend → Blend Zones.
Image 8-18
Blend menu, Zones
The Blend zones menu is displayed
Image 8-19
Blend Zone menu
2. To enable blending, put the switch to the right. The color of the switch becomes blue when activated.
3. To show blending lines on the screen, put the switch before Show lines to the right. The color of the switch becomes blue when
activated.
4. Specify the start position (offset)(1) for the blending height and width, setup an size value (2) to determine the width of the blending
area.
When the blending lines are activated, you will get a visual indication of the screen of the installed blending area.
R5906112 UDX SERIES 24/05/2017
49
8. GUI – Installation
2
1
Image 8-20
1
Start position (offset)
2
Blending width
5. First select an offset and click Menu selection to activate the selection.
Use the arrow keys to change the value (the start position of the blending)
Repeat for the other edges if necessary.
6. Select the height or width and setup a size value.
Repeat for the other edges if necessary.
The value will range from 0 to 1.0 (linear to S-curved), with a default value of 0.5.
Example of the use of blending
When projecting an image with 2 projectors, there is always an small overlap that should be corrected by using the blending function.
In order to obtain a satisfying result for the Blend function, the overlap / Blend zone are recommended to be
at least 10% of the picture width.
The basic principle is that the overlap setup in the source shall correspond with the blend width setup for the projector. That means
that if the overlap zone for the source is set to 500 pixels, the width of the blend zone for the projector also must be set to 500 pixels.
First step is to align the image from the projectors as accurate as possible in a mechanical way, meaning without any optical corrections. At the same time, establish an overlap in the pictures between the two screens.
Then adjust the remaining irregularities by using the shift and warp features in the projectors to obtain the last fine tuning of the
alignment.
Enable blending and activate Show lines.
First set the blending width for the right edge of the first projector. Enter a width value equal to the overlap area (width1).
Repeat for the left edge of the second projector.
Adjust the offset to cut the image on each side (masking).
50
R5906112 UDX SERIES 24/05/2017
8. GUI – Installation
Image 8-21
Set up for projector 1
Image 8-22
Set up for projector 2
8.5
Laser illumination
What can be done?
Within a certain power mode, the light output of the laser can be reduced by reducing the laser power.
How to reduce the power
1. In the main menu, select Installation → Illumination → Power.
Image 8-23
Illumination menu, Power
The actual power setting is indicated at the bottom of the Power button.
2. Use the Slider to change the power value.
R5906112 UDX SERIES 24/05/2017
51
8. GUI – Installation
Image 8-24
Laser power adjustment
52
R5906112 UDX SERIES 24/05/2017
9. GUI – System Settings
9. GUI – SYSTEM SETTINGS
Overview of features
•
Communication, LAN setup
•
GSM configuration
•
IR control
•
Themes
•
Service Menu
•
Reset
9.1
Communication, LAN setup
About a network connection
A network connection can be made via a wired connection or via the optional wireless unit.
9.1.1
Introduction to a Network connection
DHCP
Dynamic host configuration protocol. DHCP is a communications protocol that lets network administrators manage
centrally and automate the assignment of IP addresses in an organization’s network. Using the Internet Protocol, each
machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users
with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address
must be entered manually at each computer and, if computers move to another location in another part of the network,
a new IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from
a central point and automatically sends a new IP address when a computer is plugged into a different place in the
network.
IP
Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.
Subnet mask
A number that is used to identify a subnetwork so that IP addresses can be shared on a local area network.
Default Gateway
A router that serves as an entry point into and exit point out of a network. For example, a local network (LAN) may
need a gateway to connect it to a wide area network (WAN) or to the Internet.
MAC address
Media Access Control address. Unique hardware number, used in combination with the IP-address to connect to the
network (LAN or WAN).
What should be set up for an Ethernet address?
Two ways can be used to assign an address:
•
use the Automatic setting so that an automatic address will be assigned.
•
Assign manually an IP address, Net-mask (subnet-mask), (default) gateway address.
-
Set the IP-Address field to the desired value. This must NOT be 0.0.0.0 for static IP-Address assignment. The IP address
identifies a projector’s location on the network in the same way a street address identifies a house on a city block. Just as
a street address must identify a unique residence, an IP address must be globally unique and have a uniform format.
-
Set the Subnet-Mask as appropriate for the local subnet.
-
Set the Default-Gateway to the IP-Address of the local router (MUST be on the local subnet!) on the same network as this
projector that is used to forward traffic to destinations beyond the local network. This must not be 0.0.0.0. If there is no
router on the projector’s local subnet then just set this field to any IP-Address on the subnet.
R5906112 UDX SERIES 24/05/2017
53
9. GUI – System Settings
9.1.2
Wired IP address set up
How to automatically set up the IP address
1. In the main menu, select System Settings → Communication → LAN.
Image 9-1
Communication menu, LAN
The LAN menu is displayed
Image 9-2
LAN menu
2. To enable Automatic, put the switch to the right. The color of the switch becomes blue.
An automatic IP is assigned.
When connected, it is indicated with the connection symbol and the indication Connected.
3. Select APPLY and click OK.
How to manually set up the IP address
1. In the main menu, select System Settings → Communication → LAN.
Image 9-3
Communication menu, LAN
The LAN menu is displayed
Image 9-4
LAN menu
54
R5906112 UDX SERIES 24/05/2017
9. GUI – System Settings
2. Disable Automatic. Put the switch to the left. The switch becomes gray.
3. Use the ▲ or ▼ key to select Address and press OK button to activate the input box.
4. Use the ▲ or ▼ key to change the selected character.
Use the ◄ or ► key to select another character.
Note: Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way,
the next character will be selected automatically.
5. Repeat steps 4 and 5 for the Subnet mask and Default Gateway.
6. Select APPLY and click OK to confirm all changes.
When the connection is established, it is indicated with the connection symbol and the indication Connected.
9.2
GSM configuration
Only possible when a GSM module with SIM card is installed in the projector.
What can be done ?
To configure the projector software with the installed SIM card, a correct PIN code (4digits) must be entered.
As the PIN code cannot be checked with the one on the SIM card, ensure to enter the correct PIN code.
When your SIM card is blocked, you have to remove the SIM card from the GSM module and to insert the SIM
card in a mobile phone so that you can enter the PUK code to unblock the SIM card.
How to activate
1. In the main menu, select System Settings → Communication → GSM.
Image 9-5
Communication menu, GSM
The GSM pin code input menu is displayed. The current configured PIN code is indicated next to Pin input field. If the code is
still the same, it is not necessary to enter the PIN code again. If it is a PIN code, continue with next step.
Image 9-6
Enter PIN code
2. Enter the 4 digits of the pin code and select APPLY and click OK.
R5906112 UDX SERIES 24/05/2017
55
9. GUI – System Settings
9.3
IR control
Overview
•
Broadcast address
•
Projector address
•
IR sensors
9.3.1
Broadcast address
About broadcast address
Broadcast address is a common address that can be set on the projector. That can be “0” or “1”.
Any command coming from a remote control programmed with that common address will be executed.
How to the broadcast address
1. In the main menu, select System Settings → Communication → IR Control.
Image 9-7
Communication menu, IR control
The IR control menu is displayed.
Image 9-8
IR control menu
2. To change the broadcast address select the radio button of your choice.
The following choices are possible:
-
Generic IR (address 0)
-
Barco broadcast IR (address 1)
3. Select APPLY and click OK to apply the changes.
9.3.2
Projector address
About individual projector address
Before a projector, and only this projector, can be controlled via a remote control, an individual address must be entered in the
projector.
This individual projector address can then be used to control the projector via remote control.
Next to an individual projector address, each projector has also a broadcast address for group control.
How to change
1. In the main menu, select System Settings → Communication → IR Control.
56
R5906112 UDX SERIES 24/05/2017
9. GUI – System Settings
Image 9-9
Communication menu, IR control
The IR control menu is displayed.
Image 9-10
IR control menu
2. Select the current projector address and enter a new address.
3. Select APPLY and click OK to apply the changes.
From now on the projector will only listen to this new address and to its broadcast address.
9.3.3
IR sensors
What can be done?
Each IR sensor can be individually disabled or enabled.
When all sensors are turned off, the projector will no longer respond to signals from the remote control. To re-enable the sensors,
use the menu keypad on the projector.
How to disable
1. In the main menu, select System Settings → Communication → IR Control.
Image 9-11
Communication menu, IR control
The IR control menu is displayed.
Image 9-12
IR control menu
R5906112 UDX SERIES 24/05/2017
57
9. GUI – System Settings
2. To disable an IR sensor, select the slider and drag to the left.
A blue slider means an active IR sensor.
A gray slider means an inactive IR sensor.
3. Select APPLY and click OK to apply the changes.
9.4
Themes
About Themes
Themes are used to apply a predefined functionality to the OSD display. There are two options: light (default) or dark.
How to select a different interface theme
1. In the main menu, select System Settings →Themes.
Image 9-13
System Settings Menu — Themes.
2. In the themes menu, select the desired Theme.
You can choose one of the following: Light, or Dark.
9.5
Service Menu
About the service menu
The service menu can only be entered with a Service code.
Image 9-14
Service code
If you have a service code, select Service code with the arrow keys and click OK to enter the entry mode. Enter the code with the
numeric keys and select OK and click OK on to confirm. Otherwise select DISCARD and click OK to return to the System Settings
menu.
Overview
58
•
Service – Color
•
Service – Statistics
•
Lens Calibration
•
Lens features
R5906112 UDX SERIES 24/05/2017
9. GUI – System Settings
9.5.1
Service – Color
CAUTION: The native colors have been measured and set during factory production. Do not change them,
unless parts of the optical path have been replaced due to servicing.
If you need to change the native colors on the device, make sure to also perform a P7 calibration, using the
Projector Toolset and a chroma meter. For more info on P7 calibration, refer to the Projector Toolset Reference
guide.
How to adjust the P7 native settings
1. In the main menu, System Settings → Service.
Image 9-15
2. Enter the service code.
3. In the Service menu, select Color.
Image 9-16
The Color menu will be displayed.
Image 9-17
4. Select the desired value to change and confirm.
5. Change the values to the desired position, taking into account the color gamut values.
6. Select APPLY and click OK.
9.5.2
Service – Statistics
What can be seen?
The statistics screen shows the general information about the projector.
The following items will be displayed:
•
Laser runtime
•
Laser Strikes
•
Projector Runtime
•
System time
•
Current Uptime
R5906112 UDX SERIES 24/05/2017
59
9. GUI – System Settings
How to display the statistics
1. In the main menu, System Settings → Service.
Image 9-18
2. Enter the service code.
3. In the Service menu, select Statistics.
Image 9-19
The Statistics will be displayed.
Image 9-20
9.5.3
Lens Calibration
Lens calibration is a time consuming operation.
How to calibrate
1. In the main menu, System Settings → Service.
Image 9-21
2. Enter the service code.
3. In the Service menu, select Lens Calibration.
60
R5906112 UDX SERIES 24/05/2017
9. GUI – System Settings
Image 9-22
System Settings menu — Lens Calibration
The Lens Calibration menu is displayed.
Image 9-23
Lens Calibration menu
4. In the Lens Calibration menu, select the desired calibration action and click OK.
You can select one of the following functions:
-
Horizontal shift
-
Vertical shift
The text Calibration in progress will be displayed next to selected function until the calibration is completed.
When an error is detected, the message Calibration Error is displayed next to function.
9.5.4
Lens features
What can be done?
Some lens features can be disabled once they are correctly aligned so that a misalignment during a show is not possible.
How to enable/disable
1. In the main menu, System Settings → Service.
Image 9-24
2. Enter the service code.
3. In the Service menu, select Lens features.
Image 9-25
Service menu, lens features
R5906112 UDX SERIES 24/05/2017
61
9. GUI – System Settings
The Lens features menu is displayed.
Image 9-26
Lens features
Depending on the lens type, different functions are available such as:
-
Focus
-
Horizontal lens shift
-
Vertical lens shift
-
Shutter
-
Zoom
4. To enable/disable a feature, click on the slider and drag it to the left to disable the feature or the right to enable the feature.
When enabled, the slider becomes blue;
When disabled, the slider is gray.
9.6
Reset
What can be done?
All settings and values on the projector can be reset to its default values. This can be done for one or more settings separately, or
all settings together (factory reset).
Default settings
The following settings are default settings:
Setting
Default value
ImageConnector
Color Space
auto
Signal Range
auto
ImageFeatures
Contrast
mid value
Brightness
mid value
Saturation
mid value
Screen size
5120x3200 / 2560x1600
4 corner
Warp off, no warp
ImageResolution
Output Resolution
4K UHD
Optics
High Contrast
Off
ImageWarp
ImageSource
Source files
Standard
ImageRealColor
P7 Realcolor
all set to native
ImageOrientation
Orientation
Table, Front
UserInterface
Theme
Light
Illumination
Power
100%
ImageBlend
Blend Width
disabled, all value to zero
offset
How to reset one or more projector settings
1. In the main menu, select System Settings → Reset.
62
R5906112 UDX SERIES 24/05/2017
9. GUI – System Settings
Image 9-27
System Settings menu, Reset
The Reset menu is displayed.
Image 9-28
Reset menu
2. Navigate to the checkbox next to the settings that need to be reset and press OK.
Multiple selection are possible.
3. Select RESET and press OK to reset all selected settings.
How to reset all projector settings
1. In the main menu, select System Settings → Reset.
2. In the Reset menu, select RESET ALL and click OK.
R5906112 UDX SERIES 24/05/2017
63
9. GUI – System Settings
64
R5906112 UDX SERIES 24/05/2017
10. Status menu
10. STATUS MENU
This is a status menu only. No changes can be made to settings from this menu.
Overview
•
Status menu overview
10.1 Status menu overview
Status menu
While in the main menu, press Status.
Image 10-1
Status overview
Source status
Displays active source information
Product
Displays active product information:
•
Article number: Projector article / part number
•
Serial number: Projector serial number
•
Firmware: Projector software package version
•
Model name: Projector model name
Illumination
Shows the used light source power (in %) and runtime.
Communication
Lists the projector IP address.
Warp
Warp status
Flex
Current light output
R5906112 UDX SERIES 24/05/2017
65
10. Status menu
66
R5906112 UDX SERIES 24/05/2017
11. Maintenance
11. MAINTENANCE
About this chapter
This chapter contains general maintenance procedures.
Overview
•
Cleaning the lens
•
Cleaning the exterior of the projector
11.1 Cleaning the lens
To minimize the possibility of damage to optical coatings, or scratches to lens surfaces follow the cleaning
procedure as described here precisely.
Necessary tools
•
Compressed air.
•
Clean Toraysee® cloth or any micro fiber lens cleaning cloth.
•
Clean cotton cloth.
Necessary parts
Lens cleaner (e.g. Carl Zeiss lens cleaner or Purasol® or any water-based lens cleaner)
How to clean the lens?
1. Blow off dust with clean compressed air (or pressurized air cans1) .
2. Clean with lens cleaner together with a clean lens cleaning cloth to remove the dust and contamination. Use big wipes in one
single direction.
Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.
3. Use a dry lens cleaning cloth to remove left liquid or stripes. Polish with small circles.
4. If there are still fingerprints on the surface, wipe them off with lens cleaner together with a clean lens cleaning cloth. Polish again
with a dry one.
If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.
11.2 Cleaning the exterior of the projector
How to clean the exterior of the projector ?
1. Switch off the projector and unplug the projector from the mains power net.
2. Clean the housing of the projector with a damp cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild
detergent solution.
1. Pressurized air cans are not efficient if there is too much dust on the surface, the pressure is too low
R5906112 UDX SERIES 24/05/2017
67
11. Maintenance
68
R5906112 UDX SERIES 24/05/2017
A. Specifications
A. SPECIFICATIONS
About this chapter
This chapter gives an overview of the specification of the UDX projector as well as the dimensions and the center of gravity.
Overview
A.1
•
Specifications of the UDX 4K32
•
Specifications of the UDX 4K22
•
Specifications of the UDX W32
•
Specifications of the UDX W22
•
Specifications of the UDX U32
•
Dimensions of a UDX
•
Dimensions of the rigging frame
•
Dimensions of the flight case
•
Technical Regulations
Specifications of the UDX 4K32
Specifications
Projector type
4K UHD 3-chip DLP digital projector
Technology
0.9" DMD™ x3
Resolution
3,840 x 2,160 (4K UHD) / 2,560 x 1,600 (native)
Brightness
31,000 (WQ)/30,000 (4K UHD) center lumens*
Contrast ratio
2,000:1
Brightness uniformity
90%
Aspect ratio
16:10
ScenergiX
Horizontal and vertical edge blending
Lenses
TLD+ 0.8-1.16:1 ; 1.25-1.6:1 ; 1.5-2.0:1 ; 2.0-2.8:1 ; 2.8-4.5:1 ; 4.5-7.5:1 ; 7.5-11.5:1
Optical lens shift
V: -100% to +130% / H: +/- 40% on zoom lenses (memorized)
Color correction
P7
Light source
laser phosphor with inorganic phosphor wheel
Light source lifetime
+20,000 hrs
Optical dowser
Standard
Picture-in-picture
Two sources simultaneously
Orientation
360°
Sealed DLP™ core
standard
DMX 512
standard
WARP
Direct adjust OSD + toolset
Integrated web server
Yes
CLO (constant light output)
Standard
3D
Active eye wear (optional), passive circular (optional); 3 flash up to 200Hz
Inputs
Dual HDBt; HDMI 2.0 (HDCP 2.2); DP 1.2 (HDCP 1.3); Quad SDI/HDSDI/dual
HDSDI/6G/BarcoLink
Optional Inputs
Quad DP1.2
Input resolutions
From NTSC up to 4K (4,096 x 2,160)
Max. pixel clock
600 MHz
Software tools
Projector Toolset + Android app + iOS app
Control
XLR wired + IR, RS232, Wifi, GSM (opt)
R5906112 UDX SERIES 24/05/2017
69
A. Specifications
A.2
Network connection
10/100 base-T, RJ-45 connection, Wifi (optional)
Power requirements
120-160V / 200-240V (+/- 10%), 20A, 50-60Hz
Max. power consumption
2,900W nom/3,100W max / STBY less than 10W
Noise level (typical at 25°C/77°F)
52dB(A)
Operational ambient temperature
0-40°C / 32°-104°F
Operational humidity
0-80% (non condens)
Dissipation BTU
Max. 10,921 BTU/h
Dimensions (WxLxH)
660 x 830 x 350 mm / 25.98 x 32.67 x 13.77 inches
Shipping Dimensions
(LxWxH) 1,200 x 800 x 685 mm / 47.24 x 31.49 x 26.96 inches
Weight
92kg (202 lbs)/shipping weight from factory: 110kg (242 lbs)
Standard accessories
Power cord, wireless/XLR wired rugged remote control
Certifications
Compliant with UL60950-1 and EN60950-1 complies with FCC rules & regulations, part
15 Class A and CE EN55032 Class A, Rohs
Warranty
3 years
*
+/- 10%
Specifications of the UDX 4K22
Specifications
70
Projector type
4K UHD 3-chip DLP digital projector
Technology
0.9" DMD™ x3
Resolution
3,840 x 2,160 (4K UHD) / 2,560 x 1,600 (native)
Brightness
21,000 (WQ)/20,000 (4K UHD) center lumens*
Contrast ratio
2,000:1
Brightness uniformity
90%
Aspect ratio
16:10
ScenergiX
Horizontal and vertical edge blending
Lenses
TLD+ 0.8-1.16 ; 1.25-1.6:1 ; 1.5-2.0:1 ; 2.0-2.8:1 ; 2.8-4.5:1 ; 4.5-7.5:1 ; 7.5-11.5:1
Optical lens shift
Vert -100% to +130% / Hor +/-40% on zoom lenses memorized
Color correction
P7
Light source
laser phosphor with inorganic phosphor wheel
Light source lifetime
+20,000 hrs
Optical dowser
Standard
Picture-in-picture
Two sources simultaneously
Sealed DLP™ core
Standard
Orientation
360°
DMX 512
standard
WARP
Direct adjust OSD + toolset
Integrated web server
Yes
CLO (constant light output)
Standard
3D
Active eye wear (optional), passive circular (optional); 3 flash up to 200Hz
Inputs
Dual HDBt; HDMI 2.0 (HDCP 2.2); DP 1.2 (HDCP 1.3); Quad SDI/HDSDI/dual
HDSDI/6G/BarcoLink
Optional Inputs
Quad DP1.2
Input resolutions
From NTSC up to 4K (4,096 x 2,560)
Max. pixel clock
600 Mhz
R5906112 UDX SERIES 24/05/2017
A. Specifications
A.3
Software tools
Projector Toolset + Android app + iOS app
Control
XLR wired + IR, RS232, Wifi, GSM (opt)
Network connection
10/100 base-T, RJ-45 connection, Wifi (optional)
Power requirements
120-160 V / 200-240 V (+/- 10%), 20 A, 50-60 Hz (reduced power on 110 V)
Max. power consumption
1,900W @ 230 volts STBY<10W
Noise level (typical at 25°C/77°F)
TBD
Operational ambient temperature
0°-40°C/ 32°-104°F (45°C reduced power)
Operational humidity
0-80% (non condens)
Dissipation BTU
Max. 6,600 BTU/h
Dimensions (WxLxH)
660 x 830 x 350 mm (25.98 x 32.67 x 13.77")
Shipping Dimensions
(LxWxH)1,200 x 980 x 760 mm (47.24 x 38.58 x 29.92")
Weight
87.5 kg (193 lbs)/shipping weight from factory: 105kg (231lbs)
Standard accessories
Power cord, wireless/XLR wired rugged remote control
Certifications
Compliant with UL60950-1 and EN60950-1, complies with FCC rules & regulations, part
15 Class A and CE EN55032 Class A, Rohs
Warranty
3 years
*
+/- 10%
Specifications of the UDX W32
Specifications
Projector type
WUXGA 3-chip DLP digital projector
Technology
0.96" DMD™ x3
Resolution
1,920 x 1,200
Brightness
32,000 center lumens*
Contrast ratio
2,000:1
Brightness uniformity
90%
Aspect ratio
16:10
ScenergiX
Horizontal and vertical edge blending
Lenses
TLD+ 0.73:1 ; 1.2:1 ; 0.8-1.16 ; 1.25 -1.6:1 ; 1.5-2.0:1 ; 2.0-2.8:1 ; 2.8-4.5:1 ; 4.5-7.5:1 ;
7.5-11.5:1
Optical lens shift
V: -100% to +130% / H: +/-40% on zoom lenses (memorized)
Color correction
P7
Light source
laser phosphor with inorganic phosphor wheel
Light source lifetime
+20,000 hrs
Optical dowser
Standard
Picture-in-picture
Two sources simultaneously
Sealed DLP™ core
standard
Orientation
360°
DMX 512
standard
WARP
Direct adjust OSD + toolset
Integrated web server
Yes
CLO (constant light output)
Standard
3D
Active eye wear (optional), passive circular (optional); 3 flash up to 200Hz
Inputs
Dual HDBt; HDMI 2.0 (HDCP 2.2); DP 1.2 (HDCP 1.3); Quad SDI/HDSDI/dual
HDSDI/6G/BarcoLink
Optional Inputs
Quad DP1.2
R5906112 UDX SERIES 24/05/2017
71
A. Specifications
A.4
Input resolutions
From NTSC up to 4K (4,096 x 2,160)
Max. pixel clock
600 MHz
Software tools
Projector Toolset + Android app + iOS app
Control
XLR wired + IR, RS232, Wifi, GSM (opt)
Network connection
10/100 base-T, RJ-45 connection, Wifi (optional)
Power requirements
120-160V / 200-240V (+/- 10%), 20A, 50-60Hz
Max. power consumption
2,900W nom/3,100W max. / STBY less than 10W
Noise level (typical at 25°C/77°F)
52dB(A)
Operational ambient temperature
0-40°C / 32°-104°F
Operational humidity
0-80% (non condens)
Dissipation BTU
Max. 10,921 BTU/h
Dimensions (WxLxH)
660 x 830 x 350 mm / 25.95 x 32.7 x 13.78 inches
Shipping Dimensions
(LxWxH) 1,200 x 800 x 685 mm / 47.24 x 31.49 x 26.96 inches
Weight
92kg (202 lbs)/shipping weight from factory: 110kg (242 lbs)
Standard accessories
Power cord, wireless/XLR wired rugged remote control
Certifications
Compliant with UL60950-1 and EN60950-1 complies with FCC rules & regulations, part
15 Class A and CE EN55032 Class A, Rohs
Warranty
3 years
*
+/- 10%
Specifications of the UDX W22
Specifications
72
Projector type
WUXGA 3-chip DLP digital projector
Technology
0.96" DMD™ x3
Resolution
1,920 x 1,200
Brightness
22,000 center lumens*
Contrast ratio
2,000:1
Brightness uniformity
90%
Aspect ratio
16:10
ScenergiX
Horizontal and vertical edge blending
Lenses
TLD+ 0.73:1 ; 1.2:1 ; 1.25 -1.6:1 ; 1.5-2.0:1 ; 2.0-2.8:1 ; 2.8-4.5:1 ; 4.5-7.5:1 ; 7.5-11.5:1
Optical lens shift
Vert -100% to +130% / Hor +/-40% on zoom lenses memorized
Color correction
P7
Light source
laser phosphor with inorganic phosphor wheel
Light source lifetime
+20,000 hrs
Optical dowser
Standard
Picture-in-picture
Two sources simultaneously
Sealed DLP™ core
standard
Orientation
360°
DMX 512
standard
WARP
Direct adjust OSD + toolset
Integrated web server
Yes
CLO (constant light output)
Standard
3D
Active eye wear (optional), passive circular (optional); 3 flash up to 200Hz
R5906112 UDX SERIES 24/05/2017
A. Specifications
A.5
Inputs
Dual HDBt; HDMI 2.0 (HDCP 2.2); DP 1.2 (HDCP 1.3); Quad SDI/HDSDI/dual
HDSDI/6G/BarcoLink
Optional Inputs
Quad DP1.2
Input resolutions
From NTSC up to 4K (4,096 x 2,560)
Max. pixel clock
600 Mhz
Software tools
Projector Toolset + Android app + iOS app
Control
XLR wired + IR, RS232, Wifi, GSM (opt)
Network connection
10/100 base-T, RJ-45 connection, Wifi (optional)
Power requirements
120-160V / 200-240V (+/- 10%), 20A, 50-60Hz (reduced power on 110v)
Max. power consumption
1,900 W @ 230 volts/ STBY less than 10W
Noise level (typical at 25°C/77°F)
TBD
Operational ambient temperature
0°-40°C/ 32°-104°F (45°C reduced power)
Operational humidity
0-80% (non condens)
Dissipation BTU
Max. 6,600 BTU/h
Dimensions (WxLxH)
660 x 830 x 350 mm (25.98 x 32.67 x 13.77")
Shipping Dimensions
(LxWxH) 1200 x 800 x 685 mm / (47.24 x 31.49 x 26.96")
Weight
87.5kg (193 lbs)/shipping weight from factory: 105kg (231 lbs)
Standard accessories
Power cord, wireless/XLR wired rugged remote control
Certifications
Compliant with UL60950-1 and EN60950-1 complies with FCC rules & regulations, part
15 Class A and CE EN55032 Class A, Rohs
Warranty
3 years
*
+/- 10%
Specifications of the UDX U32
Specifications
Projector type
UXGA 3-chip DLP digital projector
Technology
0.96" DMD™ x3
Resolution
1,600 x 1,200
Brightness
30,000 center lumens*
Contrast ratio
2,000:1
Brightness uniformity
90%
Aspect ratio
4:3
ScenergiX
Horizontal and vertical edge blending
Lenses
TLD+ 0.73:1 ; 1.2:1 ; 0.8-1.16 ; 1.25-1.6:1 ; 1.5-2.0:1 ; 2.0-2.8:1 ; 2.8-4.5:1 ; 4.5-7.5:1 ;
7.5-11.5:1
Optical lens shift
V: -100% to +130% / H: +/- 40% on zoom lenses (memorized)
Color correction
P7
Light source
laser phosphor with inorganic phosphor wheel
Light source lifetime
+20,000 hrs
Optical dowser
Standard
Picture-in-picture
Two sources simultaneously
Sealed DLP™ core
standard
Orientation
360°
DMX 512
standard
WARP
Direct adjust OSD + toolset
Integrated web server
Yes
R5906112 UDX SERIES 24/05/2017
73
A. Specifications
74
CLO (constant light output)
Standard
3D
Active eye wear (optional), passive circular (optional); 3 flash up to 200Hz
Inputs
Dual HDBt; HDMI 2.0 (HDCP 2.2); DP 1.2 (HDCP 1.3); Quad SDI/HDSDI/dual
HDSDI/6G/BarcoLink
Optional Inputs
Quad DP1.2
Input resolutions
From NTSC up to 4K (4,096 x 2,160)
Max. pixel clock
600 MHz
Software tools
Projector Toolset + Android app + iOS app
Control
XLR wired + IR, RS232, Wifi, GSM (opt)
Network connection
10/100 base-T, RJ-45 connection, Wifi (optional)
Power requirements
120-160V / 200-240V (+/- 10%), 20A, 50-60Hz
Max. power consumption
2,900W nom/3,100W max / STBY less than 10W
Noise level (typical at 25°C/77°F)
52dB(A)
Operational ambient temperature
0-40°C / 32°-104°F
Operational humidity
0-80% (non condens)
Dissipation BTU
Max. 10,921 BTU/h
Dimensions (WxLxH)
660 x 830 x 350 mm / 25.98 x 32.7 x 13.78 inches
Shipping Dimensions
(LxWxH) 1,200 x 800 x 685 mm / 47.24 x 31.49 x 26.96 inches
Weight
92kg (202 lbs)/shipping weight from factory: 110kg (242lbs)
Standard accessories
Power cord, wireless/XLR wired rugged remote control, bottom rigging kit/clamps
Certifications
Compliant with UL60950-1 and EN60950-1, complies with FCC rules & regulations, part
15 Class A and CE EN55032 Class A, Rohs
Warranty
3 years
*
+/- 10%
R5906112 UDX SERIES 24/05/2017
A. Specifications
A.6
Dimensions of a UDX
36
223
385
Overview
437
20
624
664
796
20
20
836
408
624
312
20
1
Image A-1
Dimensions, in mm
1
A.7
Geometrical centre
Dimensions of the rigging frame
Overview
385
1018,97
773,72
843,94
803,38
50
463,3
978,38
Image A-2
Dimensions, in mm
R5906112 UDX SERIES 24/05/2017
75
A. Specifications
A.8
Dimensions of the flight case
Overview
350
781,5
958
431,5
1133
Image A-3
Dimensions, in mm
A.9
Technical Regulations
Certificates
10
Image A-4
EAC mark
Image A-9
FCC label
76
Image A-5
Rohs
Image A-10
RCM mark
RoHS
Image A-6
Rohs OK
Image A-7
CE mark
Image A-8
CCC mark
Image A-11
SGS mark
R5906112 UDX SERIES 24/05/2017
B. Environmental information
B. ENVIRONMENTAL INFORMATION
Overview
B.1
•
Disposal information
•
Turkey RoHS compliance
•
Contact information
•
Download Product Manual
Disposal information
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and
electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee
Disposal of batteries in the product
This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately
from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will
appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects
on the environment and human health.
B.2
Turkey RoHS compliance
Turkey RoHS compliance
Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.
[Republic of Turkey: In conformity with the WEEE Regulation]
B.3
Contact information
Barco contact information
Registered office address: President Kennedypark 35, 8500 Kortrijk, Belgium
Contact address: Beneluxpark 21, 8500 Kortrijk, Belgium
Importers contact information
To find your local importer, contact Barco directly or one of Barco’s regional offices via the contact information given on Barco’s web
site, www.barco.com.
R5906112 UDX SERIES 24/05/2017
77
B. Environmental information
Made in information
The made in country is indicated on the product ID label on the product itself.
Production date
The month and year of production is indicated on the product ID label on the product itself.
B.4
Download Product Manual
Download Product Manual
Product manuals and documentation are available online at www.barco.com/td.
Registration may be required; follow the instructions given on the website.
IMPORTANT! Read Installation Instructions before connecting equipment to the mains power supply.
78
R5906112 UDX SERIES 24/05/2017
Download PDF
Similar pages