ISC2028 Rev C
INSTALLATION, OPERATION, & PARTS
Models C2025 C3025 C4025 C5025 C7000
SWIMCLEAR™ CARTRIDGE FILTERS
MODEL
EFFECTIVE FILTRATION
RATE
DESIGN FLOW RATE
Residential
Commercial
FT2
M2
GPM
LPM
C2025
225
20.9
84
318
C3025
325
30.2
122
462
C4025
425
39.5
150
568
C5025
525
48.8
150
568
C7000
680
63.2
150
568
MAXIMUM WORKING PRESSURE FOR ALL MODELS 50 PSI (3.45 BAR)
ATTENTION INSTALLER: THIS MANUAL CONTAINS IMPORTANT INFORMATION
ON THE OPERATION, AND SAFE USE OF THIS EQUIPMENT.
THIS MANUAL IS INTENDED FOR THE END USER OF THIS PRODUCT
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 2 of 12
SWIMCLEAR CARTRIDGE FILTER
ISC2028 REV C
This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look for one of the
following signal words and be alert to the potential for personal injury or death.
WARNING Warns about hazards that could cause serious personal injury or, death, and or major property
damage and if ignored presents a potential hazard.
CAUTION Warns about hazards that will or can cause minor or moderate personal injury and/or property damage
and if ignored presents a potential hazard. It can also make consumers aware of actions that are unpredictable and unsafe.
The NOTICE label indicates special instructions that are important but not related to hazards.
READ, UNDERSTAND, AND FOLLOW ALL SAFETY AND OPERATION
INSTRUCTIONS. FAILURE TO FOLLOW SAFETY AND OPERATION INSTRUCTIONS CAN RESULT
IN SEVERE PERSONAL INJURY OR DEATH.
CAUTION To reduce risk of injury, do not permit children to use or climb on this product. Closely
supervise children at all times. The ANSI/NSPI-4 Standard (above-ground and on-ground pools) advises that
components such as the filtration system, pumps, and heaters be positioned to prevent their being used as a
means of access to the pool by young children.
WARNING COMPONENT SEPARATION HAZARD
Pool and spa water circulation systems operate under hazardous pressure during start up, normal
operation, and possibly after pump shut off. Pressure in system can cause explosive component
separation of the upper filter body if safety and operation instructions are not followed. Severe
personal injury or death can result.
This product should be installed and serviced only by a qualified pool professional.
TO AVOID COMPONENT SEPARATION
•
•
•
•
•
•
•
•
•
•
•
•
Follow all safety and operation instructions.
Do not operate water circulation system if a system component is assembled improperly, damaged, missing, or not a
genuine Hayward component.
Before performing maintenance on the water circulation system, verify all system and pump controls are in OFF position
and filter manual air relief valve is in the OPEN position.
Use ONLY Hayward clamp system components: DEX2421JKIT clamp assembly, DEX2421J2 nut/bolt assembly, and a
DEX2422Z2 metal reinforced seal.
Non-Hayward components may fail in use and cause explosive separation.
Never rely on hand tightening the clamp nut to the clamp bolt. Using a ¾” socket on a torque wrench, torque clamp nut
and clamp bolt to 150 inch-lbs.
Before starting system pump, insure filter manual air relief valve body is in LOCK position in filter upper body.
Before starting the system pump, verify that all system valves are set in a position to allow water from the filter to return
back to the pool.
Before starting the system pump, the manual air relief valve must be in the OPEN position.
When starting pump, do not stand over or near filter.
If water leakage appears in the area of the filter tank clamp, immediately turn off all system circulation pumps and
electrical power. Do not return to the filter until all water flow has stopped. Reassemble the clamp system per the
instructions in this owner’s manual to stop the leak.
Return to filter to close manual air relief valve only when a steady stream of water (Not air or air and water mix) is
discharged from the manual air relief valve.
Do not change filter control valve position while system pump is running.
WARNING EXCESS PRESSURE HAZARD
Pressure testing of the pump and filter system in excess of the 50 PSI can cause explosive separation
of the components. Component separation can result in severe personal injury or death.
WARNING ELECTROCUTION HAZARD
High Voltage electricity is present in the pool and spa equipment. High voltage electricity can cause
shock and electrocution. Shock and electrocution can result in severe personal injury or death.
•
•
•
•
•
All electrical wiring MUST be in conformance with applicable local codes, regulations and the
National Electrical Code (NEC).
Before performing any service or maintenance on electrical equipment turn off all electrical power.
Contact a licensed electrician or building inspector for information on local electrical codes for bonding requirements.
Verify water discharge from the filter manual air relief valve is directed away from electrical devices.
Do not locate pump controls over or near filter.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 3 of 12
SWIMCLEAR CARTRIDGE FILTER
ISC2028 REV C
WARNING – SUCTION ENTRAPMENT HAZARD.
Suction in suction outlets and/or suction outlet covers that are, damaged, broken, cracked,
missing, or unsecured can cause severe injury and/or death due to the following entrapment
hazards:
Hair Entrapment- Hair can become entangled in suction outlet cover.
Limb Entrapment- A limb inserted into an opening of a suction outlet sump or suction outlet
cover that is damaged, broken, cracked, missing, or not securely attached can result in a
mechanical bind or swelling of the limb.
Body Suction Entrapment- A negative pressure applied to a large portion of the body or
limbs can result in an entrapment.
Evisceration/ Disembowelment Entrapment- A negative pressure applied directly to the
intestines through an unprotected suction outlet sump or suction outlet cover that is,
damaged, broken, cracked, missing, or unsecured can result in evisceration/
disembowelment entrapment.
Mechanical Entrapment- There is potential for jewelry, swimsuit, hair decorations, finger,
toe or knuckle to be caught in an opening of a suction outlet cover resulting in mechanical
entrapment.
TO REDUCE THE RISK OF ENTRAPMENT HAZARDS:
•
•
•
•
•
•
•
•
•
•
A minimum of two functioning suction outlets per pump must be installed. Suction outlets
in the same plane (i.e. floor or wall), must be installed a minimum of three feet (3’)
[1 meter] apart, as measured from near point to near point.
Dual suction outlets shall be placed in such locations and distances to avoid “dual
blockage” by a user.
Dual suction outlets shall not be located on seating areas or on the backrest for such
seating areas.
The pool or spa circulation system shall be designed to comply with ANSI/APSP-7 2006.
Suction outlet covers shall conform to ANSI/ASME A112.19.8
Never use Pool or Spa if any suction outlet component (cover/grate) is damaged, broken,
cracked, missing, or not securely attached.
Immediately replace damaged, broken, cracked, missing, or not securely attached suction
outlet components.
The CPSP as well as the ICC International Residential Code Part IX, Appendix G, Section
AG106 specifies the installation of a safety vacuum release system conforming to ASME
A112.19.17, or an approved gravity drain system.
Failure to remove pressure test plugs and/or plugs used in winterization of the pool/spa
from the suction outlets can result in an increased potential for suction entrapment.
Failure to keep suction outlet components clear of debris, such as leaves, dirt, hair, paper
and other material can result in an increased potential for suction entrapment.
Suction outlet covers and grates have a finite life. They should be inspected frequently
and replaced within specified life.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 4 of 12
SWIMCLEAR CARTRIDGE FILTER
ISC2028 REV C
GENERAL INFORMATION
Your Hayward SwimClearTM cartridge filter combines superior water filtration with ease of operation and totally
corrosion-free construction. With filtration ratings to 9000 gallons (34,000 liters) per hour, they are designed for
continuous or intermittent operation, for installation above or below the pool water line, for fresh or salt water swimming
pools or spas. SwimClear™ filters utilize multiple reusable, reinforced polyester filter cartridge elements to provide a
high degree of water clarity and long filter cycles with minimum care.
REQUIRED CLEARANCE
A
“B” SIDE
“C” ABOVE
IN
CM
IN
CM
IN
CM
C2025
32.5
83
18
46
15
38
C3025
34.5
88
18
46
16
41
C4025
40.5
103
18
46
18
46
C5025
46.5
118
18
46
22
56
C7000
52.5
133
18
46
28
71
INSTALLATION
WARNING
This product should be installed and
serviced only by a qualified pool professional.
B
1. The filter system should be installed
on a level concrete slab or other rigid
base. Select a well drained and
vented area, one that does not flood
when it rains. Position the filter so
that the piping connections, and
winter drain are convenient and
accessible for operation, service,
maintenance and winterizing.
2. Position filter body such that all
operation and safety labels are
visible.
3. Position filter so the filter will drain by
gravity.
4. If practical, place pump and filter in
the shade to shield it from continuous,
direct heat from the sun.
5. Connect the pool suction plumbing
between the skimmer, pool outlet
(from the pool) and the pump.
6. Install the plumbing from the filter to
the pool (return to the pool).
7. Do not locate pump controls over or
near filter.
8. Verify water discharge from the
manual air relief valve(MAR) is
directed away from electrical devices.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
SWIMCLEAR CARTRIDGE FILTER
Page 5 of 12
ISC2028 REV C
STARTING THE PUMP and FILTER SYSTEM
WARNING
Before Starting the Pump
1. Use ONLY Hayward clamp system components; DEX2421JKIT clamp system, DEX2421J2 nut/bolt assembly,
DEX2422Z2 metal reinforced seal. Non-Hayward clamp components may fail in use and cause explosive
component separation. Verify that upper and lower filter bodies are properly secured with the filter body clamp.
Never rely on hand tightening the clamp nut to the clamp bolt. Using a ¾” socket on a torque wrench, torque clamp
nut to clamp bolt to 150 inch-lbs. Verify that the filter manual air relief body is in the LOCK position, and no filter
components are missing, damaged or not genuine Hayward components. (See Fig 2)
2. Close filter drain. Note: Filter plug requires an o-ring seal. (See Fig 4)
3. Open all system valves to allow water from the pool to the filtration system and from the filter to return to the pool.
4. Place the manual air relief valve in OPEN position. (See Fig 2)
Starting Pump
1.
When starting system pump, do not stand over or near filter. If water leakage appears at filter tank clamp,
immediately turn off all system circulation pumps and all electrical power. Do not return to the filter until all water
leakage has stopped.
Reassemble the clamp system per the instructions on page 7 in this owner’s manual to stop leak.
2.
Return to filter to CLOSE manual air relief valve only when a steady stream of water (not air or, air and water mix)
is discharged from the manual air relief valve.
CLAMP
NUT
Figure 1
CLAMP
BOLT
Figure 2
OPERATION
WARNING
FILTERING
Filtration starts as soon as flow is steady through the filter. As the filter
removes dirt from the pool water, the accumulated dirt causes a resistance
to flow. As a result, the gauge pressure will rise and the flow will decrease.
When the pressure rises 7-10 psi (.49-.69 bar) above the starting pressure,
or when the flow decreases below the desired rate, clean or replace the
filter cartridge elements. Once your filter is running and there is a pressure
reading, line up the green arrow with the current reading. (See Fig 3) When
the pressure rises to or above the red or second arrow, it is time to clean or
replace your filter cartridge elements.
Manual Air Relief Shown Open
In Locked Position
Figure 3
By recording the initial starting pressure (with clean filter elements) a determination can be made when the filter cartridge
elements should be replaced rather than cleaned. After the filter elements have been cleaned and reinstalled if the
starting pressure is higher than 6 PSI above the starting pressure with the new filter cartridge elements, the filter cartridge
elements should be replaced the next time the gauge arrow reaches the red arrow.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 6 of 12
SWIMCLEAR CARTRIDGE FILTER
ISC2028 REV C
MAINTAINING YOUR FILTER
WARNING
This product should be installed and serviced only by a
qualified pool professional.
Figure 4
FILTER DISASSEMBLY INSTRUCTIONS
1. Turn off all system circulation pumps and all electric power on
the equipment pad.
2. Set all system valves in a position to prevent water flow to the
filter.
3. The manual air relief valve must be placed in the OPEN
position. (Fig 6)
4. Remove filter drain plug (Fig 4) and drain water from filter.
5. Using 3/4” wrenches, loosen and remove the clamp nut and
the clamp bolt. (Fig 5)
6. Holding both ends of the filter clamp carefully spread the
clamp ends. Remove the clamp by lifting over the upper filter
body. Do not to drop the clamp during removal, because the
clamp could be damaged. Do not strike the clamp with metal
tools as they can damage the clamp.
7. Lift off upper filter body. Do not use the pressure gauge to lift
the upper filter body.
Clamp Nut
Figure 5
Clamp Bolt
Figure 6
Manual Air Relief Shown in Open
REMOVING CARTRIDGES
1. Remove the top closure plate, which is exposed when the upper filter body is
removed. (Fig 4)
2. Remove the filter cartridge elements by using slight rocking motion and lifting up.
3. Clean filter cartridge elements.
CLEANING CARTRIDGES
The Cartridge filter element can be cleaned by washing inside and outside with a garden hose. After hosing cartridge, for
best results, carefully brush the pleated surface to remove fine particles. Do not pressure wash as it can damage the filter
element.
You may find some debris on the cartridge pleats, which may not have been removed with hosing.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 7 of 12
SWIMCLEAR CARTRIDGE FILTER
ISC2028 REV C
FILTER RE-ASSEMBLY INSTRUCTIONS
WARNING
RE-INSTALLING CARTRIDGES
1.
Flush and drain any dirt or debris from the bottom of the lower filter
body.
2.
Flush any dirt or debris from the upper filter body and from around
the manual air relief area.
3.
Carefully replace the cartridges over the hubs on the bottom
manifold.
4.
Place top closure plate securely on top of cartridges.
CLEAN SEAL RING AND SEAL SURFACE
1.
Remove filter tank seal.
2.
With a clean cloth, wipe the lower filter body seal surface and
clean seal of all dirt and debris. (Fig 4) Do not use a solvent.
3.
With a clean cloth wipe the upper filter body seal surface.
Figure 7
Notice: • Do not use any petroleum solvents to clean filter
components.
• Do not lubricate DEX2422Z2 seal.
Clamp bolt
WARNING
Rounded end
of nut
This product should be installed and serviced only by a qualified
pool professional.
Figure 8
BODY AND CLAMP RE-ASSEMBLY
1.
Place the metal reinforced seal on lower filter
Tighten clamp
Clamp Bolt
body. (Fig 4) Place upper filter body on metal
bolt and nut
reinforced seal and lower filter body in a
using a
position which allows all operation and safety
torque
labels to be clearly visible and the upper filter
body to be centered on the lower filter body.
wrench to 150
Press down firmly and evenly on the upper
inch-lbs.
filter body to seat the seal. (Fig 7)
Clamp Nut
2.
Replace the filter clamp around the upper and
Figure 9
lower filter bodies. Hold the clamp ends to
position the clamp on the filter bodies with the clamp ends adjacent to the safety and operation labels on the filter
bodies. (Fig 7)
3.
Insert clamp bolt through the clamp ends and thread the clamp nut onto clamp bolt with rounded end of the nut
(Fig 8) towards the ends of the clamp.
4.
Never rely on hand tightening of clamp nut to clamp bolt. Using a 3/4” socket on a torque wrench, torque clamp nut
to clamp bolt to 150 inch-lbs. (Fig 9)
DO NOT HIT OR STRIKE CLAMP WITH HAMMER OR METAL TOOLS.
5.
Follow Operation Instructions for “Starting the Pump and Filter System” (Page 5).
VACUUMING POOL
Vacuuming can be performed directly into the filter whenever needed.
Clean cartridges after vacuuming, if required.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 8 of 12
SWIMCLEAR CARTRIDGE FILTER
ISC2028 REV C
REMOVING THE MANUAL AIR RELIEF VALVE
WARNING
This product should be installed and serviced only by a
qualified pool professional.
Your Filter comes with a Manual Air Relief Valve (MAR) preinstalled from the factory.
For Qualified pool professionals only: If MAR valve needs to
be serviced, follow these instructions carefully.
1. Turn off all system circulation pumps and all electric power
on the equipment pad.
2. Set all system valves in a position to prevent water from
flowing to the filter.
3. The manual air relief valve must be placed in the OPEN
Figure 10
position.
4. Wait until all water leakage has stopped.
Manual Air relief Shown Open
5. Grasp the MAR body at the flats, turn the MAR
In Locked Position
counterclockwise until the indicator on the on the MAR
Rotate
counterclockwise
to UNLOCK
flange is aligned with the “UNLOCK” position on the upper
filter body.
6. Pull straight up to remove the MAR, a slight rocking motion may help.
This product should be installed and serviced only by a qualified pool professional.
RE-INSTALLATION OF THE MANUAL AIR RELIEF VALVE
1.
Check the o-ring seals, replace as needed.
2.
With a clean cloth, wipe upper filter body and o-ring groove. Remove all dirt and debris.
3.
Align the notch in the MAR Flange with notch on top of the upper filter body.
4.
Press the MAR straight down into the upper filter body.
5.
Turn the MAR clockwise until the indicator is aligned with the “LOCK” position on the upper filter body.
6.
Verify the MAR discharge points away from all electrical connections.
WINTERIZING FILTER
WARNING
This product should be installed and serviced only by a qualified pool professional.
In areas where subfreezing temperatures can be expected, the filter should be drained to protect the filter from
damage.
1. The filter should be disassembled and the filter cartridges elements cleaned or replaced.
2. Follow directions under FILTER DISASSEMBLY INSTRUCTIONS
3. Then follow REMOVING CARTRIDGES per instructions
4. Reassemble per FILTER RE-ASSEMBLY INSTRUCTIONS.
5. Be sure to leave the drain plug unattached during the winter season to avoid cracking the filter body.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
SWIMCLEAR CARTRIDGE FILTER
Page 9 of 12
ISC2028 REV C
SERVICE AND REPAIRS
Consult your local authorized Hayward dealer or service center. No returns may be made directly to the factory without
the expressed written authorization of Hayward Pool Products.
SUGGESTED POOL CHEMISTRY LEVELS
pH
7.2 to 7.8
TOTAL ALKALINITY
80 to 120 ppm
CALCIUM HARDNESS
200 to 400 ppm
COMBINED CHLORINE
.2 ppm Maximum
CHLORINE (STABILIZED)
1.0 to 3.0 ppm
CHLORINE STABILIZER
(Cyanuric Acid)
60 to 80 ppm
PROBLEM SOLVING LIST
REMEDY
LOW WATER FLOW
1. Check skimmer and pump
strainer baskets for debris.
SHORT FILTER CYCLES
1. Check for algae in pool and
super-chlorinate as required.
2. Check for restrictions in
intake and discharge lines.
2. Be sure chlorine and pH
levels are in proper range
(adjust as required).
3. Check for air leak in intake
line (indicated by bubbles
returning to pool).
POOL WATER WON’T CLEAR UP
1. Check chlorine, pH and total
alkalinity levels and adjust as
required.
2. Be sure flow rate through filter
is sufficient.
3. Operate filter for longer
periods.
4. Clean Filter Cartridges,
(see Page 6)
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 10 of 12
Item Part No.
1
2
3
4
5
6a
6b
6c
6d
6e
7
ECX2712B1
DEX2420Z8A
CCX1000N
CCX1000V
DE2420MAR2
DEX2420BT
DEX3620BT
DEX4820BT
DEX6020BT
DEX7220BT
DEX2421J2
8
DEX2421JKIT
9
10a
DEX2422Z2
CX2020DA
10b
CX3020DA
10c
CX5020DA
10d
CX3020D4
11a
11b
11c
11d
11e
CX800Z4
CX3000Z3
CX4000Z3
CX5000Z3
CX7000Z3
12a
CX480XRE
12b
CX580XRE
12c
CX880XRE
12d
CX875RE
12e
CX1280XRE
12f
CX1380RE
12g
CX590XRE
-
CX7020M
13
14
15
16
17
18
19
20
21
22
CX3000F1
CX3020FB
DEX360M
CX3000C
DEX2420AT
SP1022C
DEX2420DCKIT
SX220Z2
DEX2420F
DE2400PAK2CS
23
DEX2420LA6PAK
24
25
DEX2420LA6PAK
DEX2420LA6PAK
SWIMCLEAR CARTRIDGE FILTER
ISC2028 REV C
Description
Pressure Gauge
O-Ring Kit (Set of 2)
Air Relief Valve Nut
Manual Air Relief w/O-Ring
Manual Air Relief Assembly
Upper Filter Body C2025
Upper Filter Body C3025
Upper Filter Body C4025
Upper Filter Body C5025
Upper Filter Body C7000
Clamp Bolt & Nut
Clamp System including:
Clamp, Clamp Nut and Bolt,
Hang tag, Metal Reinforced
Seal, and Labels
Metal Reinforced Seal
Top Closure Plate C2025
Top Closure Plate
C3025,C4025
Top Closure Plate C5025
Top Closure Plate C7000
Series
Air Relief Tube Assy C2025
Air Relief Tube Assy C3025
Air Relief Tube Assy C4025
Air Relief Tube Assy C5025
Air Relief Tube Assy C7000
Cartridge Element C2025
4 Required
Cartridge Element C3025
4 Required
Cartridge Element C4025
4 Required
Cartridge Element C4520
Series
4 Required
Cartridge Element C5025
4 Required
Cartridge Element C5520
Series
4 Required
Cartridge Element C7000
Series
8 Required
Mid plate Connector C7000
only
Inlet Elbow
Outlet Elbow
O-Ring
Bottom Collector Manifold
Lower Filter Body
1 ½” Drain Plug w/O-Ring
Strap kit (Optional)
O-ring
Bulkhead Fitting
Cartridge Filter Plumbing Kit
Label Pack: Includes all
Warning and Operation
Label’s Hang Tag, Wire Tie
and Owner’s Manual
Complete as listed above
Complete as listed above
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 11 of 12
SWIMCLEAR CARTRIDGE FILTER
ISC2028 REV C
HAYWARD® LIMITED WARRANTY
To Buyer, as original purchaser of this equipment, Hayward Pool Products, 620 Division Street, Elizabeth, New Jersey, warrants its
products free from defects in materials and workmanship for a period of ONE (1) year from the date of purchase.
Parts which fail or become defective during the warranty period, except as a result of freezing, negligence, improper installation, use, or
care, shall be repaired or replaced, at our option, without charge, within 90 days of the receipt of defective product, barring unforeseen
delays.
To obtain warranty replacements or repair, defective components or parts should be returned, transportation paid, to the place of
purchase, or to the nearest authorized Hayward service center. For further Hayward dealer or service center information, contact
Hayward customer service department. No returns may be made directly to the factory without the express written authorization of
Hayward Pool Products.
To original purchasers of this equipment, Hayward Pool Products warrants its products to be free from defects in materials and
workmanship for a period of ONE (1) year from the date of purchase.
Filters which become defective during the warranty period, except as a result of freezing, negligence, improper installation, use or care,
shall be repaired or replaced, at our option, without charge.
All other conditions and terms of the standard warranty apply.
Hayward shall not be responsible for cartage, removal and/or reinstallation labor or any other such costs incurred in obtaining warranty
replacements.
The Hayward Pool Products warranty does not apply to components manufactured by others. For such products, the warranty
established by the respective manufacturer will apply.
Some states do not allow a limitation on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
*Supersedes all previous publications.
Hayward Pool Products
620 Division Street
Elizabeth, NJ 07207
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Page 12 of 12
SWIMCLEAR CARTRIDGE FILTER
ISC2028 REV C
PRODUCT REGISTRATION
(Retain For Your Records)
DATE OF INSTALLATION ____________________
INITIAL PRESSURE GAUGE READING (CLEAN FILTER)
_______________________
PUMP MODEL ________________
HORSEPOWER
_______________________
FILTER MODEL ________________
SERIAL NUMBER _______________________
▲Retain this Warranty Certificate in a safe and convenient location for your records
DETACH HERE: REGISTER ONLINE AT WWW.HAYWARDNET.COM
or Fill out bottom portion completely and mail within 10 days of purchase/installation.
-----------------------------------------------------------------------------------------------------------Mail to: Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207, Attn: Warranty Dept.
Please Print Clearly:
Warranty Registration Card
Name__________________________________________________
Purchased Date:____________________________________________
Address________________________________________________
Purchased from: ______________________________________________
City______________________ State_________ Zip____________
Company name________________________________________________
E-mail Address__________________________________________
Address_______________________________________________________
City__________________________ State_________ Zip_______________
Product Purchased ______________________________________
Product Serial No. _______________________________________
□ New Installation
Please send me more information on these other
products from Hayward:
□ Replacement
□ Pump □ Filter □ Automatic Pool Cleaner □ Light
□ Chlorinator □ Skimmer □ Heater □ Heat Pump
□ Salt/Chlorine Generator □ Controls
Type of Pool:
□ Vinyl □ Fiberglass □ Gunite □ Above-ground
Size of Pool__________________________
May we contact you for future product promotions and offerings?
Yes
REGISTER YOUR WARRANTY ON-LINE AT WWW.HAYWARDNET.COM
© Hayward Pool Products. 2008 All rights reserved.
Pomona, CA
Clemmons, NC
Nashville, TN
West Palm Beach, FL
North Kingstown, RI
Oakville, ON, Canada
www.haywardpool.com
St. Vulbas, France
Wuxi, China
No
Download PDF
Similar pages