SUPERSERVER®
7048R-TR
7048R-TRT
USER’S MANUAL
1.0a
Preface
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other reproductive harm.
Manual Revision 1.0a
Release Date: April 5, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Preface
About This Manual
This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 7048RTR/7048R-TRT. Installation and maintainance should be performed by experienced
technicians only.
The SuperServer 7048R-TR/7048R-TRT is a high-end server based on the SC745TQ-R920B 4U tower/rackmountable chassis and the X10DRi/X10DRi-T dual
processor serverboard.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the server system and describes the main features of the X10DRi/X10DRi-T serverboard
and the SC745TQ-R920B chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 7048RTR/7048R-TRT into a rack and check out the server configuration prior to powering up the system. If your server was ordered without processor and memory
components, this chapter will refer you to the appropriate sections of the manual
for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: Standardized Warning Statements
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 7048R-TR/7048R-TRT.
Printed in the United States of America
iii
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
Preface
Notes
Chapter 5 provides detailed information on the X10DRi/X10DRi-T serverboard,
including the locations and functions of connections, headers and jumpers. Refer
to this chapter when adding or removing processors or main memory and when
reconfiguring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC745TQ-R920B server chassis.
You should follow the procedures given in this chapter when installing, removing or
reconfiguring SATA or peripheral drives and when replacing system power supply
units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specifications
iv
v
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Table of Contents
3-2
1-1Overview.......................................................................................................... 1-1
Power............................................................................................................... 3-1
3-3
HDD.................................................................................................................. 3-2
NIC1................................................................................................................. 3-2
Memory............................................................................................................ 1-2
NIC2................................................................................................................. 3-2
SATA ............................................................................................................... 1-2
Information LED............................................................................................... 3-3
PCI Expansion Slots........................................................................................ 1-2
I/O Ports........................................................................................................... 1-2
Graphics Controller.......................................................................................... 1-2
1-4
Power Fail........................................................................................................ 3-3
3-4 Drive Carrier LEDs..........................................................................................3-4
Server Chassis Features................................................................................. 1-3
Chapter 4 Standardized Warning Statements for AC Systems
SATA Subsystem.............................................................................................. 1-3
4-1
Warning Definition............................................................................................ 4-1
Front Control Panel.......................................................................................... 1-3
Installation Instructions..................................................................................... 4-4
Cooling System................................................................................................ 1-3
Circuit Breaker................................................................................................. 4-5
Contacting Supermicro..................................................................................... 1-5
Power Disconnection Warning......................................................................... 4-6
Equipment Installation...................................................................................... 4-8
Restricted Area................................................................................................. 4-9
2-1Overview.......................................................................................................... 2-1
2-2
Unpacking the System..................................................................................... 2-1
2-3
Preparing for Setup.......................................................................................... 2-1
Battery Handling............................................................................................. 4-10
Redundant Power Supplies........................................................................... 4-12
Backplane Voltage......................................................................................... 4-13
Choosing a Setup Location.............................................................................. 2-1
Comply with Local and National Electrical Codes......................................... 4-14
Warnings and Precautions............................................................................... 2-2
Product Disposal............................................................................................ 4-15
Rack Precautions............................................................................................. 2-2
Hot Swap Fan Warning.................................................................................. 4-16
Server Precautions........................................................................................... 2-2
Rack Mounting Considerations........................................................................ 2-3
Power Cable and AC Adapter ....................................................................... 4-18
Ambient Operating Temperature................................................................. 2-3
Chapter 5 Advanced Serverboard Setup
Reduced Airflow.......................................................................................... 2-3
5-1
Unpacking........................................................................................................ 5-2
Circuit Overloading...................................................................................... 2-3
Reliable Ground.......................................................................................... 2-3
Handling the Serverboard................................................................................ 5-1
Precautions...................................................................................................... 5-1
Mechanical Loading.................................................................................... 2-3
2-5
About Standardized Warning Statements........................................................ 4-1
System Power.................................................................................................. 1-3
Chapter 2 Server Installation
2-4
Control Panel LEDs......................................................................................... 3-2
Power............................................................................................................... 3-2
Serverboard Features...................................................................................... 1-2
Processors....................................................................................................... 1-2
1-3
Control Panel Buttons...................................................................................... 3-1
Reset................................................................................................................ 3-1
Chapter 1 Introduction
1-2
Table of Contents
5-2
Connecting Cables........................................................................................... 5-2
Installing the System into a Rack.................................................................... 2-4
Connecting Data Cables.................................................................................. 5-2
Identifying the Sections of the Rack Rails...................................................... 2-4
Connecting Power Cables............................................................................... 5-2
Installing the Chassis Rails.............................................................................. 2-5
Connecting the Control Panel.......................................................................... 5-2
Installing the Rack Rails.................................................................................. 2-6
5-3
I/O Ports........................................................................................................... 5-3
Installing the Server into the Rack................................................................... 2-7
5-4
Installing the Processor and Heatsink............................................................. 5-4
Installing an LGA2011 Processor..................................................................... 5-4
Chapter 3 System Interface
3-1Overview.......................................................................................................... 3-1
vi
Installing a CPU Heatsink................................................................................ 5-7
vii
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Removing the Heatsink.................................................................................... 5-7
5-5
Installing Memory............................................................................................. 5-8
Memory Support............................................................................................... 5-8
DIMM Installation............................................................................................. 5-8
Processor & Memory Module Population Configuration............................. 5-9
5-6
Adding PCI Add-On Cards............................................................................. 5-10
5-7
Serverboard Details........................................................................................5-11
X10DRi/X10DRi-T Quick Reference.............................................................. 5-12
5-8
Connector Definitions .................................................................................... 5-14
5-9
Jumper Settings............................................................................................. 5-20
5-10 Onboard Indicators......................................................................................... 5-23
5-11 SATA Ports..................................................................................................... 5-24
5-12 Installing Software.......................................................................................... 5-25
SuperDoctor® 5............................................................................................. 5-26
5-13 Onboard Battery............................................................................................. 5-27
Chapter 6 Advanced Chassis Setup
6-1
Static-Sensitive Devices................................................................................... 6-1
Precautions...................................................................................................... 6-1
6-2
Front Control Panel.......................................................................................... 6-3
6-3
System Fans.................................................................................................... 6-4
Fan Failure....................................................................................................... 6-4
6-4
Drive Bay Installation....................................................................................... 6-6
SATA Hard Drives............................................................................................ 6-6
SATA Backplane............................................................................................... 6-7
Storage Module................................................................................................ 6-8
6-5
Power Supply................................................................................................. 6-10
Power Supply Failure..................................................................................... 6-10
Chapter 7 BIOS
7-1 Introduction....................................................................................................... 7-1
7-2 Main Setup....................................................................................................... 7-2
7-3 Advanced Setup Configurations...................................................................... 7-4
7-4 Event Logs..................................................................................................... 7-29
7-5 IPMI................................................................................................................ 7-31
7-6
Security Settings............................................................................................ 7-34
7-7
Boot Settings.................................................................................................. 7-35
7-8 Save & Exit.................................................................................................... 7-37
Appendix A BIOS Error Beep Codes
Appendix B System Specifications
viii
Chapter 1: Introduction
Chapter 1
Introduction
1-1Overview
The SuperServer 7048R-TR/7048R-TRT is a high-end server comprised of two main
subsystems: the SC745TQ-920B 4U server chassis and the X10DRi/X10DRi-T dual
processor serverboard. Please refer to our web site for information on operating
systems that have been certified for use with the system (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 7048R-TR/7048R-TRT, as listed below:
•Two passive CPU heatsinks (SNK-P0048PS)
•Three 8-cm system fans (FAN-0074L4)
•Two 8-cm rear exhaust fans (FAN-0082L4)
•One air shroud (MCP-310-49001-0N)
•SATA Accessories
One SATA backplane (CSE-SAS-743TQ-O-P)
Eight drive carriers (MCP-220-00092-0B)
Optional
•One rackmount kit (CSE-PT26L-B)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
•Supermicro product manuals: http://www.supermicro.com/support/manuals/
•Product drivers and utilities: ftp://ftp.supermicro.com
•Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm
•If you have any questions, please contact our support team at:
support@supermicro.com
1-1
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
1-2 Serverboard Features
Chapter 1: Introduction
1-3 Server Chassis Features
The SuperServer 7048R-TR/7048R-TRT is built around the X10DRi/X10DRi-T, a
The following is a general outline of the main features of the SC745TQ-920B server
dual processor serverboard based on the Intel® PCH C612 chipset and designed
to provide maximum performance. Below are the main features of the X10DRi/
X10DRi-T. (See Figure 1-1 for a block diagram of the chipset).
chassis.
SATA Subsystem
The chassis was designed to support eight 3.5" hot-swap SATA hard drives.
Processors
The X10DRi/X10DRi-T supports single or dual Intel E5-2600 (v3/v4) Series Socket
R3 processors in LGA 2011 sockets. Please refer to our website for a complete
listing of supported processors (www.supermicro.com). Note that with only a single
processor installed (in the CPU1 socket), PCI-E slots 4~6 will not function.
Memory
The X10DRi/X10DRi-T has sixteen DIMM slots that can support up to 1 TB of ECC
LRDIMM or ECC RDIMM DDR4-2400/2133/1866/1600 memory. Please refer to
Chapter 5 for details on installing memory.
SATA
A SATA controller is integrated into the chipset to provide a ten-port SATA 3.0
subsystem, which is RAID 0, 1, 10 and 5 capable. Six ports are supported by the
Intel PCH (I-SATA0-5: I-SATA 4 and 5 are colored yellow to indicate that they have
embedded power to support SATA DOMs) and four are supported by the Intel SCU
(S-SATA0-3).
PCI Expansion Slots
System Power
The SC745TQ-920B features a redundant 920W power supply composed of two
separate power modules. This power redundancy feature allows you to replace a
failed power supply without shutting down the system.
Front Control Panel
The control panel on the SuperServer 7048R-TR/7048R-TRT provides you with
system monitoring and control. LEDs indicate system power, HDD activity, network
activity, system overheat and power supply failure. A main power button and a
system reset button are also included. In addition, two USB ports have been incorporated into the control panel to provide front side USB access.
Cooling System
The chassis has an innovative cooling design that includes three 8-cm hot-plug
system cooling fans located in the middle section of the chassis as well as two 8-cm
hot-plug exhaust fans located at the rear of the chassis. An air shroud channels the
airflow from the system fans to efficiently cool the processor area of the system.
The power supply module also includes a cooling fan.
The X10DRi/X10DRi-T has three PCI-E 3.0 x16 and three PCI-E 3.0 x8 expansion
slots. Note that the PCI slots are controlled by the CPU so some slots may not be
available when two CPUs are not installed on the board at the same time. See the
serverboard layout in Chapter 5 for details.
I/O Ports
The I/O ports include one COM port, a VGA (monitor) port, four USB ports, two
Ethernet LAN ports (10 Gb ports on the X10DRi-T and 1 Gb ports on the X10DRi)
and a dedicated IPMI LAN port.
Graphics Controller
The X10DRi/X10DRi-T features an integrated Aspeed 2400 controller.
1-2
1-3
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 1: Introduction
1-4 Contacting Supermicro
Headquarters
Figure 1-1. Chipset Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
PCI-E X16
VCCP1 12v
VR12.5
5 PHASE
145W
P0
DDR4 2133
SLOT 2
SNB CORE
DDR-IV
P1
P1
QPI
9.6G
P0
QPI
9.6G
#2 #3A#1 #3B DMI2
SNB CORE
DDR-IV
#1 #2 #3
DMI2
PCI-E X8 G3
PCI-E X8
DMI2
4GB/s
RMII/NCSI
#3
PCH
6.0 Gb/S
SPI
AST2400
USB 2.0
Tel:
+31 (0) 73-6400390
Fax:
+31 (0) 73-6416525
Email:
sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
USB 3.0
#12 USB2.0
Zhonghe Dist., New Taipei City 235
USB
SPI
LPC
VGA CONN
Temp Sensor
COM1
Connector
COM2
Header
Taiwan (R.O.C)
SPI
TPM HEADER
Debug Card
BIOS
HEADER
SYSTEM POWER
FRONT PANEL
1-4
FAN SPEED
CTRL
Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
SPI
BIOS
www.supermicro.nl
Asia-Pacific
Address:
#5
Super Micro Computer B.V.
's-Hertogenbosch, The Netherlands
SLOT 4
USB
BMC Boot Flash
USB 2.0
www.supermicro.com
Het Sterrenbeeld 28, 5215 ML
Web Site:
RGRMII
PCI-E X1 G2
support@supermicro.com (Technical Support)
SATA
SATA
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
RTL8211E-VB-CG
BMC
marketing@supermicro.com (General Information)
Europe
SLOT 6
#2
DDR3
SLOT 5
LAN
PCI-E X16
PCI-E X16 G3
#6/7/8
LAN3
+1 (408) 503-8008
Email:
PCI-E X16
PCI-E X8 G3 (LAN REVERSE)
PCI-E X8
PCI-E X8
PCI-E X16 G3
X540
RJ45
Fax:
Address:
PCI-E X8 G3 (LAN REVERSE)
SLOT 1
+1 (408) 503-8000
Web Site:
PCI-E X16 G3 (LAN REVERSE)
SLOT 3
PCI-E X8
VCCP0 12v
VR12.5
5 PHASE
145W
#2-8
#2-7
#2-6
#2-5
#2-4
#2-3
#2-2
#2-1
DDR4 2133
#1-8
#1-7
#1-6
#1-5
#1-4
#1-3
#1-2
#1-1
Tel:
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3992
Email:
support@supermicro.com.tw
Web Site:
www.supermicro.com.tw
1-5
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Notes
1-6
Chapter 2: Server Installation
Chapter 2
Server Installation
2-1Overview
This chapter provides a quick setup checklist to get your SuperServer 7048RTR/7048R-TRT up and running. Following these steps in the order given should
enable you to have the system operational within a minimum amount of time.
This quick setup assumes that your system has come to you with the processors and memory preinstalled. If your system is not already fully integrated with a
serverboard, processors, system memory etc., please turn to the chapter or section
noted in each step for details on installing specific components.
The 7048R-TR/7048R-TRT may be employed either as a tower or mounted in a
rack as a 4U rackmount chassis.
2-2 Unpacking the System
You should inspect the box the system was shipped in and note if it was damaged
in any way. If the server itself shows damage you should file a damage claim with
the carrier who delivered it.
Decide on a suitable location for the SuperServer 7048R-TR/7048R-TRT. It should
be situated in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fields are generated. You will also need
it placed near a grounded power outlet. Be sure to read the Rack and Server Precautions in the next section.
2-3 Preparing for Setup
The box the system was shipped in may include two sets of rail assemblies, two
rail mounting brackets and mounting screws needed for installing the system into
a rack (optional kit). Follow the steps in the order given to complete the installation
process in a minimum amount of time. Please read this section in its entirety before
you begin the installation procedure outlined in the sections that follow.
Choosing a Setup Location
•Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufficient airflow and ease in servicing.
2-1
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
•This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
Chapter 2: Server Installation
Rack Mounting Considerations
Ambient Operating Temperature
2-4 Warnings and Precautions
Rack Precautions
•Ensure that the leveling jacks on the bottom of the rack are fully extended to
the floor with the full weight of the rack resting on them.
•In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
•Always make sure the rack is stable before extending a component from the
rack.
•You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable.
•Slide/rail-mounted equipment is not to be used as a shelf or workspace.
Server Precautions
•Review the electrical and general safety precautions in Chapter 4.
•Determine the placement of each component in the rack before you install the
rails.
•Install the heaviest server components on the bottom of the rack first, and then
work up.
•Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
•Allow the hot plug drives and power supply modules to cool before touching
•This unit should be mounted at the bottom of the rack if it is the only unit in
•Always keep the rack's front door and all panels and components on the servers
•When mounting this unit in a partially filled rack, load the rack from the bottom
them.
closed when not servicing to maintain proper cooling.
the rack.
to the top with the heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
2-2
2-3
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
2-5 Installing the System into a Rack
This section provides information on installing the system into a rack unit. Rack
installation requires the use of the optional rackmount kit. If the system has already
been mounted into a rack or if you are using it as a tower, you can skip ahead to
Sections 2-5 and 2-6.
There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. The following is a guideline for installing the server into
a rack with the rack rails provided in the rackmount kit. You should also refer to the
installation instructions that came with the rack unit you are using.
Identifying the Sections of the Rack Rails
The optional rackmount kit includes two rack rail assemblies. Each of these assemblies consist of three sections: an inner fixed chassis rail that secures to the
chassis, an outer rack rail that secures directly to the rack itself and two rail brackets,
which also attach to the rack (see Figure 2-1.) The inner and outer rails must be
detached from each other to install.
To remove the inner chassis rail, pull it out as far as possible - you should hear a
"click" sound as a locking tab emerges from inside the rail assembly and locks the
inner rail. Depress the locking tab to pull the inner rail completely out. Do this for
both assemblies (one for each side).
Figure 2-1. Identifying the Sections of the Rack Rails
Chapter 2: Server Installation
Installing the Chassis Rails
You will need to remove the top cover and the feet to add rack rails to the chassis.
First, remove the top and right covers (top and left covers when standing as a tower
chassis) by first removing the screws that secure them to the chassis. Depress the
button on the top (side if tower) of the chassis to release the cover and then pull
the cover off. Then unscrew the four feet and remove them from the chassis (see
Figure 2-2).
You can now attach rack rails to the top and bottom (now the sides) of the chassis.
First add the rack handles. Then position the inner chassis rail sections you just
removed along the side of the chassis making sure the screw holes line up. Note
that these two rails are left/right specific. Screw the rail securely to the side of the
chassis (see Figure 2-3). Repeat this procedure for the other rail on the other side
of the chassis. You will also need to attach the rail brackets when installing into a
telco rack.
Locking Tabs: As mentioned, the chassis rails have a locking tab, which serves
two functions. The first is to lock the server into place when installed and pushed
fully into the rack, which is its normal position. Secondly, these tabs also lock the
server in place when fully extended from the rack. This prevents the server from
coming completely out of the rack when you pull it out for servicing.
Warning: In any instance of pulling the system from the rack, always use
a rack lift and follow all associated safety precautions.
Figure 2-2. Preparing to Install the Chassis Rails
Outer rail
Inner rail
Rail brackets
Warning: do not pick up the server with the front handles. They are designed to pull the system from a rack only.
2-4
2-5
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 2: Server Installation
Installing the Server into the Rack
Figure 2-3. Installing the Rails to the Chassis
You should now have rails attached to both the chassis and the rack unit. The next
step is to install the server into the rack. You should have two brackets in the rack
mount kit. Install these first keeping in mind that they are left/right specific (marked
with "L" and "R"). Then, line up the rear of the chassis rails with the front of the rack
rails. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting).
When the server has been pushed completely into the rack, you should hear the
locking tabs "click". Finish by inserting and tightening the thumbscrews that hold
the front of the server to the rack (see Figure 2-4).
Figure 2-4. Installing the Server into a Rack
Installing the Rack Rails
Determine where you want to place the SuperServer 7048R-TR/7048R-TRT in the
rack. (See Rack and Server Precautions in Section 2-3.) Position the fixed rack rail/
sliding rail guide assemblies at the desired location in the rack, keeping the sliding
rail guide facing the inside of the rack. Screw the assembly securely to the rack
using the brackets provided. Attach the other assembly to the other side of the rack,
making sure both are at the exact same height and with the rail guides facing inward.
Slide rail mounted equipment is not to be used as a shelf or a work space.
Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the floor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.
Warning: When initially installing the server to a rack, test that the rail
locking tabs engage to prevent the server from being overextended. Have
a rack lift in place as a precaution in case the test fails.
2-6
Note: figures are for illustrative purposes only. Always install servers to the bottom
of a rack first.
2-7
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Notes
2-8
Chapter 3: System Interface
Chapter 3
System Interface
3-1Overview
The control panel on the 7048R-TR/7048R-TRT has several LEDs and two buttons. There are also two LEDs on each hard drive carrier. These LEDs keep you
constantly informed of the overall status of the system and the activity and health
of specific components.
3-2 Control Panel Buttons
There are two push-buttons located on the front of the chassis: a power on/off
button and a reset button.
Power
This is the main power button, which is used to apply or turn off the main system
power. Turning off system power with this button removes the main power but keeps
standby power supplied to the system.
Reset
Use the reset button to reboot the system.
3-1
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 3: System Interface
3-3 Control Panel LEDs
The control panel located on the front of the SC745 chassis has six LEDs that
provide you with critical information related to different parts of the system. This
section explains what each LED indicates when illuminated and any corrective action you may need to take.
Power
Indicates power is being supplied to the system's power supply. This LED should
normally be on when the system is operating.
Information LED
This LED will be solid blue when the UID function has been activated. When this
LED flashes red, it indicates a fan failure. When red continuously it indicates an
overheat condition, which may be caused by cables obstructing the airflow in the
system or the ambient room temperature being too warm. Check the routing of
the cables and make sure all fans are present and operating normally. You should
also check to make sure that the chassis covers are installed. Finally, verify that
the heatsinks are installed properly (see Chapter 5). This LED will remain flashing
or on as long as the indicated condition exists.
Information LED States
HDD
Indicates hard disk drive activity when flashing.
1
NIC1
Indicates network activity on LAN1 when flashing.
State
Indication
Continuously On (Red)
An overheat condition has occured.
Fast Blinking Red (1 Hz)
Fan Failure
Slow Blinking Red (.25 Hz)
Power Fail
Solid Blue
Local UID button has been activated.
Blinking Blue
IPM/Remote UID has been activated
Note: deactivating the UID LED must be performed in the same way it was activated.
(If the UID LED was activated via IPMI, you can only turn the LED off via IPMI and
not with the UID button.)
2
NIC2
Power Fail
Indicates network activity on LAN2 when flashing.
3-2
This LED functions only when two power supply modules have been installed in the
system and indicates a power supply module has failed (when illuminated). This
should be accompanied by an audible alarm. A backup power supply module will
take the load and keep the system running but the failed module will need to be
replaced. Refer to Chapter 6 for details on replacing the power supply. This LED
should be off when the system is operating normally.
3-3
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
3-4 Drive Carrier LEDs
•Green: Each hard drive carrier has a green LED. When illuminated, this green
LED (on the front of the hard drive carrier) indicates drive activity. A connection to the backplane enables this LED to blink on and off when that particular
drive is being accessed. Please refer to Chapter 6 for instructions on replacing
failed hard drives.
•Red: The red LED to indicate a hard drive failure. If one of the hard drives fail,
you should be notified by your system management software. Please refer to
Chapter 6 for instructions on replacing failed hard drives.
3-4
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certified technicians should attempt to install or configure
components.
Read this appendix in its entirety before installing or configuring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning Definition
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
この警告サインは危険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前,必须充分
意识到触电的危险,并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前,請注意觸
電的危險,並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。
4-1
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Warning Statements for AC Systems
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
. ‫تحذٌز!هذا الزهز ٌعًٌ خطز اًك فً حالة ٌوكي أى تتسبب فً اصابة جسذٌة‬
‫كي على علن بالوخاطز الٌاجوة عي الذوائز‬،‫قبل أى تعول على أي هعذات‬
‫الكهزبائٍة‬
‫وكي على دراٌة بالووارسات الىقائٍة لوٌع وقىع أي حىادث‬
‫استخذم رقن البٍاى الوٌصىص فً ًهاٌة كل تحذٌز للعثىر تزجوتها‬
안전을 위한 주의사항
BEWAHREN SIE DIESE HINWEISE GUT AUF.
경고!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
final de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.
GUARDE ESTAS INSTRUCCIONES.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
IMPORTANTES INFORMATIONS DE SÉCURITÉ
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
CONSERVEZ CES INFORMATIONS.
‫תקנון הצהרות אזהרה‬
‫ על מנת להזהיר את המשתמש מפני חבלה‬,‫הצהרות הבאות הן אזהרות על פי תקני התעשייה‬
‫ יש ליצור קשר עם מחלקת תמיכה‬,‫ במידה ויש שאלות או היתקלות בבעיה כלשהי‬.‫פיזית אפשרית‬
.‫ טכנאים מוסמכים בלבד רשאים להתקין או להגדיר את הרכיבים‬.‫טכנית של סופרמיקרו‬
.‫יש לקרוא את הנספח במלואו לפני התקנת או הגדרת הרכיבים במארזי סופרמיקרו‬
4-2
4-3
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Installation Instructions
Chapter 4: Warning Statements for AC Systems
Circuit Breaker
Warning!
Warning!
Read the installation instructions before connecting the system to the power source.
設置手順書
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
サーキット・ブレーカー
システムを電源に接続する前に、設置手順書をお読み下さい。
この製品は、短絡(過電流)保護装置がある建物での設置を前提としています。
警告
将此系统连接电源前,请先阅读安装说明。
警告
將系統與電源連接前,請先閱讀安裝說明。
Warnung
保護装置の定格が250 V、20 Aを超えないことを確認下さい。
警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.
警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。
¡Advertencia!
Warnung
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschlussbzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.
.‫יש לקרוא את הוראות התקנה לפני חיבור המערכת למקור מתח‬
‫اقر إرشادات التركيب قبل توصيل النظام إلى مصدر للطاقة‬
시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
4-4
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)
del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit
dépend de l'installation électrique du local. Vérifiez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.
‫ יש לוודא כי‬.‫מוצר זה מסתמך על הגנה המותקנת במבנים למניעת קצר חשמלי‬
60VDC, 20A-‫המכשיר המגן מפני הקצר החשמלי הוא לא יותר מ‬
‫هذا المنتج يعتمد على معداث الحمايت مه الدوائرالقصيرة التي تم تثبيتها في‬
‫المبنى‬
20A, 250VDC :‫تأكد من أن تقييم الجهاز الوقائي ليس أكثر من‬
4-5
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 4: Warning Statements for AC Systems
경고!
¡Advertencia!
이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
El sistema debe ser disconnected de todas las fuentes de energía y del cable
eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.
Attention
Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van
uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V, 20A.
Power Disconnection Warning
Warning!
The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.
電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、
シャーシー内部にアクセス
するには、
Le système doit être débranché de toutes les sources de puissance ainsi que de
son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.
‫אזהרה מפני ניתוק חשמלי‬
!‫אזהרה‬
‫יש לנתק את המערכת מכל מקורות החשמל ויש להסיר את כבל החשמלי מהספק‬
.‫לפני גישה לחלק הפנימי של המארז לצורך התקנת או הסרת רכיבים‬
‫يجب فصم اننظاو من جميع مصادر انطاقت وإزانت سهك انكهرباء من وحدة امداد‬
‫انطاقت قبم‬
‫انىصىل إنى انمناطق انداخهيت نههيكم نتثبيج أو إزانت مكىناث الجهاز‬
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り
外す必要があります。
경고!
警告
시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.
在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。
Waarschuwing
警告
在您打開機殼安裝或移除內部元件前,必須將系統完全斷電,並移除電源線。
Warnung
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren
of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel
getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.
4-6
4-7
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Equipment Installation
Chapter 4: Warning Statements for AC Systems
Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door
geschoold en gekwalificeerd personeel.
Warning!
Only trained and qualified personnel should be allowed to install, replace, or service
this equipment.
Restricted Area
Warning!
機器の設置
トレーニングを受け認定された人だけがこの装置の設置、交換、
またはサービスを許可
されています。
警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。
This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).
アクセス制限区域
このユニットは、
アクセス制限区域に設置されることを想定しています。
警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。
アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての
み出入りが可能です。
Warnung
警告
此部件应安装在限制进出的场所,限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifiziertem Personal gestattet werden.
¡Advertencia!
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
警告
此裝置僅限安裝於進出管制區域,進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。
Warnung
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la
maintenance de ces équipements à des personnels qualifiés et expérimentés.
!‫אזהרה‬
.‫ להחליף את הציוד או לתת שירות עבור הציוד‬,‫צוות מוסמך בלבד רשאי להתקין‬
‫يجب أن يسمح فقط للمىظفيه المؤهليه والمدربيه لتزكيب واستبدال أو خدمة هذا الجهاس‬
경고!
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.
Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.
¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.
Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.
Attention
훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.
4-8
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une
zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.
4-9
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 4: Warning Statements for AC Systems
‫אזור עם גישה מוגבלת‬
!‫אזהרה‬
‫ הגישה ניתנת בעזרת‬.‫יש להתקין את היחידה באזורים שיש בהם הגבלת גישה‬
.)'‫ מנעול וכד‬,‫כלי אבטחה בלבד (מפתח‬
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Attention
. ‫تم تخصيص هذه انىحذة نتركُبها فٍ مناطق محظورة‬
،‫َمكن انىصىل إنً منطقت محظورة فقط من خالل استخذاو أداة خاصت‬
‫قفم ومفتاح أو أٌ وسُهت أخري نالمألما‬
경고!
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및
키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.
Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.
Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.
!‫אזהרה‬
‫ יש להחליף‬.‫קיימת סכנת פיצוץ של הסוללה במידה והוחלפה בדרך לא תקינה‬
.‫את הסוללה בסוג התואם מחברת יצרן מומלצת‬
Battery Handling
.‫סילוק הסוללות המשומשות יש לבצע לפי הוראות היצרן‬
Warning!
There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
‫هناك خطر من انفجار في حالة اسحبذال البطارية بطريقة غير صحيحة فعليل‬
‫اسحبذال البطارية‬
‫فقط بنفس النىع أو ما يعادلها مما أوصث به الشرمة المصنعة‬
‫جخلص من البطاريات المسحعملة وفقا لحعليمات الشرمة الصانعة‬
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、
または同等のものを使用下さい。使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
4-10
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.
4-11
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 4: Warning Statements for AC Systems
Redundant Power Supplies
경고!
Warning!
This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.
冗長電源装置
このユニットは複数の電源装置が接続されている場合があります。
ユニットの電源を切るためには、すべての接続を取り外さなければなりません。
警告
此部件连接的电源可能不止一个,必须将所有电源断开才能停止给该部件供电。
警告
此裝置連接的電源可能不只一個,必須切斷所有電源才能停止對該裝置的供電。
.‫قد يكون لهذا الجهاز عدة اتصاالت بوحدات امداد الطاقة‬
‫يجب إزالة كافة االتصاالت لعسل الوحدة عن الكهرباء‬
이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.
Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle
aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.
Backplane Voltage
Warning!
Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.
バックプレーンの電圧
Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass
der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.
¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.
Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。
修理する際には注意ください。
警告
当系统正在进行时,背板上有很危险的电压或能量,进行维修时务必小心。
警告
當系統正在進行時,背板上有危險的電壓或能量,進行維修時務必小心。
Attention
Warnung
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute
tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche
Spannungen oder Energien auf. Vorsicht bei der Wartung.
‫אם קיים יותר מספק אחד‬
!‫אזהרה‬
‫ יש להסיר את כל החיבורים על מנת לרוקן‬.‫ליחדה יש יותר מחיבור אחד של ספק‬
.‫את היחידה‬
¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.
Tenga cuidado cuando lo revise.
Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur
le fond de panier. Prendre des précautions lors de la maintenance.
4-12
4-13
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 4: Warning Statements for AC Systems
‫מתח בפנל האחורי‬
!‫אזהרה‬
‫ יש להיזהר במהלך‬.‫קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת‬
.‫העבודה‬
‫هناك خطز مه التيار الكهزبائي أوالطاقة المىجىدة على اللىحة‬
‫عندما يكىن النظام يعمل كه حذرا عند خدمة هذا الجهاس‬
Attention
L'équipement doit être installé conformément aux normes électriques nationales
et locales.
‫תיאום חוקי החשמל הארצי‬
!‫אזהרה‬
.‫התקנת הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬
‫تركيب المعدات الكهربائية يجب أن يمتثل للقىاويه المحلية والىطىية المتعلقة‬
‫بالكهرباء‬
경고!
시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.
경고!
현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.
Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het
systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.
Comply with Local and National Electrical Codes
Warning!
Installation of the equipment must comply with local and national electrical codes.
地方および国の電気規格に準拠
機器の取り付けはその地方および国の電気規格に準拠する必要があります。
警告
设备安装必须符合本地与本国电气法规。
Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。
警告
設備安裝必須符合本地與本國電氣法規。
Warnung
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
¡Advertencia!
Warnung
La instalacion del equipo debe cumplir con las normas de electricidad locales y
nacionales.
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
4-14
4-15
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 4: Warning Statements for AC Systems
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y
reglamentos nacionales.
警告
當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。
Warnung
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
‫סילוק המוצר‬
!‫אזהרה‬
.‫סילוק סופי של מוצר זה חייב להיות בהתאם להנחיות וחוקי המדינה‬
‫عند التخلص النهائي من هذا المنتج ينبغي التعامل معه وفقا لجميع القىانين واللىائح الىطنية‬
경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
Hot Swap Fan Warning
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis
genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.
¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador
del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador
Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez
le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.
!‫אזהרה‬
‫ יש‬.‫ יתכן והמאווררים עדיין עובדים‬,‫כאשר מסירים את חלקי המאוורר מהמארז‬
‫להרחיק למרחק בטוח את האצבעות וכלי עבודה שונים מהפתחים בתוך המאוורר‬
‫مه انممكه أن انمراوح ال تسال تدورعند إزانة كتهة انمروحة مه انهيكم يجب إبقاء‬
‫األصابع ومفكات انبراغي‬
.‫وغيرها مه األشياء بعيدا عه انفتحات في كتهة انمروحة‬
Warning!
The fans might still be turning when you remove the fan assembly from the chassis.
Keep fingers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.
ファン・ホットスワップの警告
シャーシから冷却ファン装置を取り外した際、
ファンがまだ回転している可能性がありま
す。ファンの開口部に、指、
ドライバー、およびその他のものを近づけないで下さい。
警告
当您从机架移除风扇装置,风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇
4-16
경고!
섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.
Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het
ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers
en eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.
4-17
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Power Cable and AC Adapter
Chapter 4: Warning Statements for AC Systems
Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.
L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
Warning!
When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.
電源コードとACアダプター
製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター
を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ
ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表
記)を Supermicroが指定する製品以外に使用することを禁止しています。
警告
安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。
警告
安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。
Warnung
Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt
Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifizierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.
¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los
cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certificados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.
4-18
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifiés qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.
AC
‫חשמליים ומתאמי‬
!‫אזהרה‬
‫ אשר‬AC ‫ ספקים ומתאמים‬,‫ יש להשתמש בכבלים‬,‫כאשר מתקינים את המוצר‬
‫ שימוש בכל כבל או מתאם אחר יכול לגרום לתקלה או‬.‫נועדו וסופקו לשם כך‬
‫ קיים איסור‬,‫ על פי חוקי שימוש במכשירי חשמל וחוקי בטיחות‬.‫קצר חשמלי‬
‫ (כשאר מופיע עליהם קוד של‬CSA -‫ או ב‬UL -‫להשתמש בכבלים המוסמכים ב‬
.‫) עבור כל מוצר חשמלי אחר שלא צוין על ידי סופרקמיקרו בלבד‬UL/CSA
‫والكابالث الكهربائيت‬،‫عىذ تركيب الجهاز يجب استخذام كابالث التىصيل‬
‫ومحىالث التيار المتردد‬
.‫ أن استخذام أي كابالث ومحىالث أخري يتسبب في حذوث عطل أو حريق‬. ‫التي‬
‫تم تىفيرها لك مع المىتج‬
UL ‫ أو‬CSA ‫األجهسة الكهربائيت ومىاد قاوىن السالمت يحظر استخذام الكابالث‬
‫معتمذة مه قبل‬
Supermicro ‫ألي أجهسة كهربائيت أخري غير المىتجاث المعيىت مه قبل‬
(UL/CSA ‫)التي تحمل عالمت‬
경고!
제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.
Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,
stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertificeerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.
4-19
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Notes
4-20
Chapter 5: Advanced Serverboard Setup
Chapter 5
Advanced Serverboard Setup
This chapter covers the steps required to connect the data and power cables and
install add-on cards. All serverboard jumpers and connections are also described.
A layout and quick reference chart are included in this chapter for your reference.
Remember to completely close the chassis when you have finished working with
the serverboard to better cool and protect the system.
5-1 Handling the Serverboard
Electrostatic Discharge (ESD) can damage electronic com­ponents. To prevent damage to any printed circuit boards (PCBs), it is important to handle them very carefully
(see previous chapter). To prevent the serverboard from bending, keep one hand
under the center of the board to support it when handling. The following measures
are generally sufficient to protect your equipment from electric static discharge.
Precautions
•Use
a grounded wrist strap designed to prevent Electrostatic Discharge
(ESD).
•Touch a grounded metal object before removing any board from its antistatic
bag.
•Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
•When handling chips or modules, avoid touching their pins.
•Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
•For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
5-1
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
Unpacking
Figure 5-1. Control Panel Header Pins
The serverboard is shipped in antistatic packaging to avoid electrical static discharge. When unpacking the board, make sure the person handling it is static
20
19
Ground
protected.
NMI
X
X
3.3 V
FP PWRLED
5-2 Connecting Cables
UID Switch
HDD LED
The cables listed below should already be connected to the serverboard. These
include the data cables for the peripherals and control panel and the power cables.
Connecting Data Cables
NIC1 Link LED
NIC1 Activity LED
NIC2 Link LED
NIC2 Activity LED
OH/Fan Fail/
PWR Fail LED)
UID LED
Power Fail LED
The cables used to transfer data from the peripheral devices have been carefully
routed to prevent them from blocking the flow of cooling air that moves through the
system from front to back. If you need to disconnect any of these cables, you should
take care to keep them routed as they were originally after reconnecting them (make
sure the red wires connect to the pin 1 locations). The following data cables (with
their locations noted) should be connected. (See the layout for connector locations.)
•SATA (I-SATA0-5, S-SATA0-3) drive cables
•Control Panel cable (JF1)
3.3V
Ground
Ground
2
Reset
Reset Button
PWR
Power Button
1
5-3 I/O Ports
The I/O ports are located on the backplane of the motherboard. See Figure 5-2
below for the descriptions of the various I/O ports.
Figure 5-2. I/O Ports
Important! Make sure the cables do not come into contact with the fans.
4
Connecting Power Cables
6
The X10DRi/X10DRi-T has a 24-pin primary power supply connector (J24) for connection to the ATX power supply. In addition, there are two 8-pin 12V processor
power connectors (JPWR1 and JPWR2) that must be connected to your power
supply. See Section 5-9 for power connector pin definitions.
3
1
Connecting the Control Panel
JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the various front control panel buttons and LED indicators.
All JF1 wires have been bundled into a single cable to simplify this connection. Make
sure the red wire plugs into pin 1 as marked on the board. The other end connects
to the Control Panel PCB board, located just behind the system status LEDs on
the chassis. See Chapter 5 for details and pin descriptions.
5
7
8
9
2
IO Ports
1
COM1 Port
6
USB Port 13 (USB 3.0)
2
USB Port 0 (USB 2.0)
7
LAN Port 1*
3
USB Port 1 (USB 2.0)
8
LAN Port 2*
4
IPMI LAN Port
9
VGA Port
5
USB Port 12 (USB 3.0)
* These are Gb LAN ports on the X10DRi and 10 Gb LAN ports on the X10DRi-T.
5-2
5-3
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
5-4 Installing the Processor and Heatsink
Warning: When handling the processor package, avoid placing direct pressure on the
label area of the fan.
Notes
•Always connect the power cord last and always remove it before adding, re-
moving or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.
•If you buy a CPU separately, make sure that you use an Intel-certified multidirectional heatsink only.
•Make sure to install the serverboard into the chassis before you install the CPU
heatsinks.
•When receiving a serverboard without a processor pre-installed, make sure that
the plastic CPU socket cap is in place and none of the socket pins are bent;
otherwise, contact your retailer immediately.
•Refer to the Supermicro web site for updates on CPU support.
Installing an LGA2011 Processor
3. With the lever labeled 'Close 1st'
fully retracted, gently push down
on the 'Open 1st' lever to open the
load plate. Lift the load plate to
open it completely.
WA
R
NI
OP
EN
NG
!
1st
Gently push
down to pop
the load plate
open.
4. Using your thumb and the index
finger, remove the 'WARNING'
plastic cap from the socket.
5. Use your thumb and index finger
to hold the CPU by its edges. Align
the CPU keys, which are semicircle cutouts, against the socket
keys.
WA
R
NI
NG
!
6. Once they are aligned, carefully
lower the CPU straight down into
the socket. (Do not drop the CPU
on the socket. Do not move the
CPU horizontally or vertically and
do not rub the CPU against any
pins of the socket, which may
damage the CPU or the socket.)
Press down on the lever labeled
'Close 1st'
1. There are two levers on the
LGA2011 socket. First press and
release the load lever labeled
'Open 1st'.
WA
R
NI
2. Press the second load lever
labeled 'Close 1st' to release the
load plate from its locked position.
OP
EN
NG
Socket Keys
!
CPU Keys
1st
Pull lever away
from the socket
WA
R
NI
OP
EN
5-4
NG
!
1st
5-5
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
Warning: You can only install the CPU to the socket in one direction. Make sure that
the CPU is properly inserted into the socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.
Installing a CPU Heatsink
1. Place the heatsink on top of the CPU so that the four mounting holes are
aligned with those on the retention mechanism.
2. Screw in two diagonal screws (i.e. the #1 and the #2 screws) until just snug
(do not over-tighten the screws, which may damage the CPU.)
7. With the CPU in the socket, inspect the four corners of the CPU
to make sure that they are flush
with the socket.
8. Close the load plate. Lock the
lever labeled 'Close 1st', then lock
the lever labeled 'Open 1st'. Use
your thumb to gently push the
load levers down until the lever
locks.
3. Finish the installation by fully tightening all four screws.
Gently close
the load plate.
Push down and lock the
level labeled 'Close 1st'.
Removing the Heatsink
OP
EN
Warning: We do not recommend removing the CPU or the heatsink. If you do need
to remove the heatsink, please follow the instructions below to prevent damage to the
CPU or other components.
1st
1. Unplug the power cord from the power supply.
1. Unscrew and remove the heatsink screws in the
sequence shown in the picture below.
Lever Lock
2. Hold the heatsink and gently wiggle it to loosen it
from the CPU. (Do not use excessive force when
doing this!)
OP
EN
1st
Push down
and lock the
lever labeled
'Open 1st'.
5-6
3. Once the heatsink is loosened, remove it from
the CPU.
4. Clean the surface of the CPU and the heatsink
to get rid of the old thermal grease. Reapply the
proper amount of thermal grease before you reinstall the heatsink.
5-7
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
5-5 Installing Memory
Processor & Memory Module Population Configuration
For memory to work properly, follow the tables below for memory installation.
Warning: Exercise extreme care when installing or removing DIMM modules to prevent
Processors and their Corresponding Memory Modules
any possible damage.
CPU#
Memory Support
The X10DRi/X10DRi-T supports up to 1 TB of ECC LRDIMM or ECC RDIMM DDR42400/2133/1866/1600 memory. Use memory modules of the same type and speed.
See the following tables for memory installation. Please refer to the Supermicro
website for possible updates to supported memory.
DIMM Installation
Installing Memory Modules
1. Insert the desired number of DIMMs into the memory slots starting with DIMM
#P1-DIMMA1. When populating two DIMM modules within a channel, always
start with Bank1 first. For optimal memory performance, please install a pair
(or pairs) of memory modules of the same type and speed with a maximum of
12 modules (see the Memory Installation Table below).
2. Insert each DIMM module vertically into its slot. Pay attention to the notch
along the bottom of the module to avoid installing incorrectly (see Figure 5-3).
3. Gently press down on the DIMM module until it snaps into place in the slot.
Repeat for all modules.
Corresponding DIMM Modules
CPU 1
P1DIMMA1
P1DIMMB1
P1DIMMC1
P1DIMMD1
P1DIMMA2
P1DIMMB2
P1DIMMC2
P1DIMMD2
CPU2
P2DIMME1
P2DIMMF1
P2DIMMG1
P2DIMMH1
P2DIMME2
P2DIMM F2
P2DIMMG2
P2DIMMH2
Processor and Memory Module Population for Optimal Performance
Number of
CPUs+DIMMs
CPU and Memory Population Configuration Table
(For memory to work properly, please follow the instructions below.)
1 CPU &
2 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1
1 CPU &
4 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
1 CPU &
5~8 DIMMs
CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + Any memory pairs in P1DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slots
2 CPUs &
4 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
2 CPUs &
6 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1
2 CPUs &
8 DIMMs
CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2DIMMG1/P2-DIMMH1
2 CPUs &
8~16 DIMMs
CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2DIMMG1/P2-DIMMH1 + Any memory pairs in P1, P2 DIMM slots
2 CPUs &
16 DIMMs
CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1,P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/
P2-DIMMF2/P2-DIMMG2/P2-DIMMH2
Figure 5-3. DIMM Installation
Populating RDIMM/LRDIMM DDR4 Memory Modules
Speed (MT/s); Voltage (V); Slots per Channel (SPC) and
DIMMs per Channel (DPC)
Type
Release Tab
Socket Key
Release Tab
5-8
Ranks
Per DIMM
and Data
Width
DIMM Capacity
(GB)
2 Slots per Channel
1 DPC
2 DPC
E5-2600 V3
E5-2600 V4
E5-2600 V3
E5-2600 V4
4 GB
8 GB
1.2 V
1.2 V
1.2 V
1.2 V
RDIMM
SRx4
8 GB
16 GB
2133
2400
1866
2133
RDIMM
SRx8
4 GB
8 GB
2133
2400
1866
2133
RDIMM
DRx8
8 GB
16 GB
2133
2400
1866
2133
RDIMM
DRx4
16 GB
32 GB
2133
2400
1866
2133
LRDIMM
QRx4
32 GB
64 GB
2133
2400
2133
2400
LRDIMM 3DS
8Rx4
64 GB
128 GB
2133
2400
2133
2400
5-9
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
5-6 Adding PCI Add-On Cards
Chapter 5: Advanced Serverboard Setup
5-7 Serverboard Details
The 7048R-TR/7048R-TRT can accommodate six full-height, full-length PCI addon cards.
Figure 5-4. X10DRi/X10DRi-T Layout
(not drawn to scale)
Installing an Add-on Card
1. Begin by removing the shield for the PCI slot you wish to populate.
LE1
Fan6
VGA/BMC CPU1 SLOT2 PCI-E 3.0 X16
Memory
LAN CTRL
LEDM1
COM1
Fan5
BIOS
LAN2
LAN1
USB12/13
(USB 2.0)
IPMI_LAN
CPU2 SLOT6 PCI-E 3.0 X16
CPU2 SLOT5 PCI-E 3.0 X8
CLOSE 1st
CPU2
BAR CODE
MAC CODE
J29
J30
JPME2
CPU2 SLOT4 PCI-E 3.0 X16
CPU1 SLOT3 PCI-E 3.0 X8
CPU1 SLOT1 PCI-E 3.0 X8
JIPMB1
COM2
JPLAN1
JI2C2
JI2C1
JPB1
3. Finish by using a screw to secure the top of the card shield to the chassis.
The PCI slot shields protect the serverboard and its components from EMI
and aid in proper ventilation, so make sure there is always a shield covering
each unused slot.
BMC FW
JPG1
2. Fully seat the card into the slot, pushing down with your thumbs evenly on
both sides of the card.
USB0/1(3.0) USB0/1(2.0)
VGA
UID
BMC
OPEN 1st
P2 DIMMG1
P2 DIMMG2
P2 DIMMH1
P2 DIMMH2
P1 DIMMA1
P1 DIMMA2
P1 DIMMB1
P1 DIMMB2
P2 DIMME2
P2 DIMME1
P1 DIMMD2
P1 DIMMD1
P1 DIMMC2
P1 DIMMC1
T-SGPIO1
T-SGPIO2
T-SGPIO3
P2 DIMMF2
P2 DIMMF1
JTPM1
X10DRi-(T)
Rev. 1.01
JPWR1
JPI2C1
CLOSE 1st
CPU1
JPWR2
S-SATA3
Intel PCH
OPEN 1st
FAN1
FAN2
FAN3
FAN4
JOH1
JD1
JBR1
JWD1FANA
I-SATA3
JBT1 SP1
I-SATA0
I-SATA1
I-SATA2
I-SATA4
I-SATA5
S-SATA1 JSTBY1
J24 FPCTRL
JF1
LE2
USB8/9(2.0) JSD1 JSD2
USB10 (2.0) USB3/4(3.0)S-SATA2 S-SATA0 FANB JL1
USB6 (3.0)
USB2/3 USB4/5
(USB2.0)(USB2.0)
USB6/7
(USB2.0)
Battery
Notes
•Jumpers not indicated are for test purposes only and should not have their
settings changed.
•"
" indicates the location of pin 1.
•LAN1/LAN2 ports support Gigabit LAN connections on the X10DRi and 10G
LAN connections on the X10DRi-T.
5-10
5-11
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
X10DRi/X10DRi-T Quick Reference
(CPU2) Slot5
PCI-Express 3.0 x8 Slot from CPU2
(CPU2) Slot6
PCI-Express 3.0 x16 Slot from CPU2
Jumper
Description
Default Setting
JBR1
BIOS Recovery Enable/Disable
Pins 1-2 (Normal)
(T-)SGPIO1/2/3
Serial Link General Purpose I/O Headers
Internal Speaker/Buzzer
JBT1
Clear CMOS
See Section 5-9
SP1
JI2C1/JI2C2
SMB to PCI-E Slots Enable/Disable
Off (Disabled)
(BP) USB 0/1
Backpanel USB 2.0 Ports 0/1
Pins 1-2 (Enabled)
(BP) USB 12/13
Backpanel USB 2.0 Ports 12/13, or USB 3.0 Ports 0/1
Front Accessible USB 2.0 Connection Headers 2/3, 4/5
JPB1
BMC Enable/Disable
JPG1
VGA Enable/Disable
Pins 1-2 (Enabled)
(FP) USB 2/3, 4/5
JPL1
LAN1/LAN2 Enable/Disable
Pins 1-2 (Enabled)
(FP) USB Type A
JPME2
Manufacture (ME) Mode Select
Pins 1-2 (Normal)
Front Panel Accessible Type A Connector USB 3.0 Port 6 or
USB 2.0 Port 10
JWD1
Watch Dog Timer
Pins 1-2 (Reset)
J-USB3-1
Front Panel Accessible USB 3.0 Ports 3/4, USB 2.0 8/9
Connector
Description
COM1/COM2
Backplane COM Port1/Front Accessible COM2 Header
Fan1-6, FanA-B
CPU/System Fan Headers
J24
24-pin ATX Main Power Connector
JD1
Speaker/Power LED
JF1
Front Panel Control Header
JIPMB1
4-pin External BMC I2C Header (for an IPMI Card)
JL1
Chassis Intrusion Header
JOH1
Overheat LED Indicator
JPI2C1
Power Supply SMBbus I2C Header
JPWR1/2
12V 8-Pin Power Connectors
JSD1/JSD2
SATA DOM (Device on Module) Power Connectors
JSTBY1
Standby Power Connector
JTPM1
TPM (Trusted Platform Module)/Port 80 Header
JUIDB1
UID (Unit Identification) Button
(I-)SATA 0-5
SATA 3.0 Ports supported by Intel PCH
(S-)SATA 0-3
SATA 3.0 Ports supported by Intel SCU
(CPU1) Slot1
PCI-Express 3.0 x8 Slot from CPU1
(CPU1) Slot2
PCI-Express 3.0 x16 Slot from CPU1
(CPU) Slot3
PCI-Express 3.0 x8 Slot from CPU1
(CPU2) Slot4
PCI-Express 3.0 x16 Slot from CPU2
5-12
LED
Description
State
Status
LE1
Rear UID LED
Solid Blue
Unit Identified
LE2
Onboard PWR LED
On
System Power On
LEDM1
BMC Heartbeat LED
Blinking Green
BMC Normal
5-13
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
5-8 Connector Definitions
Chapter 5: Advanced Serverboard Setup
ATX Power 24-pin Connector
Pin Definitions
Pin#
Definition
Power Connectors
13
+3.3V
Pin #
1
+3.3V
Definition
A 24-pin main power supply connector
(J24) and two 8-pin power connectors
(JPWR1/JPWR2) are provided on the
serverboard. These power connectors
meet the SSI EPS 12V specification.
These power connectors must be connected to your power supply. See the
table on the right for pin definitions.
14
-12V
2
+3.3V
15
COM
3
COM
16
PS_ON
4
+5V
17
COM
5
COM
18
COM
6
+5V
19
COM
7
COM
20
Res (NC)
8
PWR_OK
21
+5V
9
5VSB
22
+5V
10
+12V
23
+5V
11
+12V
24
COM
12
+3.3V
Required Connection
Secondary Power Connector
JPWR1 and JPWR2 must also be
connected to the power supply. See
the table on the right for pin definitions.
+12V 8-pin Power
Pin Definitions
Pins
Definition
1-4
Ground
5-8
+12V
Required Connection
Power Button
The Power On connection is on pins 1
and 2 of JF1. Momentarily contacting
both pins will power on/off the system.
This button can also be configured to
function as a suspend button (with a
setting in the BIOS). To turn off the
power when the system is in suspend
mode, press the button for 4 seconds
or longer. Refer to the table on the
right for pin definitions.
Power Fail LED
to the table on the right for pin definitions.
Overheat (OH)/Fan Fail/PWR Fail/
UID LED
Connect an LED cable to pins 7 and
8 of Front Control Panel to use the
Overheat/Fan Fail/Power Fail and UID
LED connections. The red LED on pin
8 provides warnings of overheat, fan
failure or power failure. The blue LED
on pin 7 works as the front panel UID
LED indicator. Refer to the table on
the right for pin definitions.
NIC2 (LAN2) LED
The LED connections for LAN2 are on
pins 9 and 10 of JF1. Attach an LED
cable to display network activity. See
the table on the right for pin definitions.
Power Button
Pin Definitions (JF1)
Pin#
Definition
1
Power Signal
2
Ground
PWR Fail LED
Pin Definitions (JF1)
The Power Fail LED connection is
located on pins 5 and 6 of JF1. Refer
NIC1 (LAN1) LED
The LED connections for LAN1 are on
pins 11 and 12 of JF1. Attach an LED
cable to display network activity. See
the table on the right for pin definitions.
Pin#
Definition
5
3.3V
6
Ground
OH/Fan Fail/ PWR Fail/Blue_UID
LED Pin Definitions (JF1)
Pin#
Definition
7
Blue_UID LED
8
OH/Fan Fail/Power Fail
OH/Fan Fail/PWR Fail
LED Status (Red LED)
State
Definition
Off
Normal
On
Overheat
Flashing
Fan Fail
NIC2 LED
Pin Definitions (JF1)
Pin#
Definition
9
Vcc
10
Ground
NIC1 LED
Pin Definitions (JF1)
Pin#
Definition
11
Vcc
12
Ground
HDD LED
Reset Button
The Reset Button connection is
located on pins 3 and 4 of JF1 and
attaches to the reset switch on the
computer chassis. See the table on
the right for pin definitions.
5-14
Reset Button
Pin Definitions (JF1)
Pin#
Definition
3
Reset
4
Ground
The HDD LED connection is located on
pins 13 and 14 of JF1. Attach a cable
to Pin 14 to show HDD activity status.
Attach a cable to Pin 13 to use UID
switch. See the table on the right for
pin definitions.
5-15
HDD LED
Pin Definitions (JF1)
Pin#
Definition
13
UID Switch
14
HD Active
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Power LED
Chapter 5: Advanced Serverboard Setup
Power LED
Pin Definitions (JF1)
The Power LED connection is located
on pins 15 and 16 of JF1. Refer to the
table on the right for pin definitions.
Pin#
Definition
15
3.3V
16
PWR LED
The Internal Speaker, located at SP1,
can be used to provide audible indications for various beep codes. See the
table on the right for pin definitions.
Pin#
Definition
1
Ground
2
+12V
3
Tachometer
4
PWR Modulation
Beep In
Pin 2
Neg. (-)
Alarm
Speaker
Overheat/Fan Fail LED
Pin#
Definition
The JOH1 header may be connected
to an LED indicator to provide warnings of chassis overheating or fan
failure. Refer to the table on right for
pin definitions.
1
5vDC
Pin#
Definition
1
Intrusion Input
DOM Power Connectors
2
Ground
Two power connectors for DOM (Disk
On Module) devices are located at
JSD1/JSD2. Connect appropriate
cables here to provide power support
for your Serial Link DOM devices.
T-SGPIO
Pin Definitions
5-16
Pos. (+)
Overheat LED
Pin Definitions
2
Pin#
Definition
Pin
Definition
1
NC
2
NC
3
Ground
4
Data
5
Load
6
Ground
7
Clock
8
NC
NC= No Connection
T-SGPIO 0-3, 4/5 & S-SATA 0-3 Support
OH Active
OH/Fan Fail LED
Status
Chassis Intrusion
Pin Definitions
The Chassis Intrusion header is designated JL1. Attach an appropriate
cable from the chassis to inform you
of a chassis intrusion when the chassis is opened
Three SGPIO (Serial Link General
Purpose Input/Output) headers are
located at T-SGPIO1/2/3 to support the
SATA ports. See the table on the right
for pin definitions.
Definitions
Pin 1
Fan Header
Pin Definitions
Chassis Intrusion
T-SGPIO1/2/T-SGPIO-S Headers
Pin#
Internal Speaker
Fan Headers
There are eight fan headers on the
serverboard (Fan 1-Fan 6, Fan A, Fan
B), all of which are 4-pin fans. Pins
1-3 of the fan headers are backward
compatible with the traditional 3-pin
fans. (Fan speed control is supported
with 4-pin fans only.) See the table
on the right for pin definitions. The
fan speeds are controlled by Thermal
Management via IPMI 2.0 interface.
Internal Buzzer (SP1)
Pin Definition
State
Message
Solid
Overheat
Blinking
Fan Fail
DOM PWR
Pin Definitions
Pin#
Definition
1
+5V
2
Ground
3
Ground
TPM/Port 80 Header
Pin Definitions
Pin #
Definition
Pin #
Definition
TPM Header/Port 80 Header
1
LCLK
2
GND
A Trusted Platform Module/Port 80
header is located at JTPM1 to provide
TPM support and Port 80 connection.
Use this header to enhance system
performance and data security. See
the table on the right for pin definitions.
3
LFRAME#
4
<(KEY)>
5
LRESET#
6
+5V (X)
7
LAD 3
8
LAD 2
9
+3.3V
10
LAD1
11
LAD0
12
GND
13
SMB_CLK4
14
SMB_DAT4
15
+3V_DUAL
16
SERIRQ
T-SGPIO#
I-SATA Ports Supported
T-SGPIO1
I-SATA Ports 0/1/2/3 Supported
T-SGPIO2
I-SATA Ports 4/5 Supported
17
GND
18
CLKRUN# (X)
T-SGPIO3
S-SATA Ports 0/1/2/3 Supported
19
LPCPD#
20
LDRQ# (X)
5-17
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
Standby Power
Pin Definitions
Standby Power
The Standby Power header is located
at JSTBY1 on the serverboard. See
the table on the right for pin definitions. (You must also have a cable to
use this feature.)
Definition
Two USB 2.0 ports (USB 0/1) and two
1
+5V Standby
2
Ground
3
Wake-up
USB 2.0/3.0 ports (USB12/13) are located on the I/O backpanel. (Note that
USB ports 12/13 support both USB
2.0 and 3.0.) In addition, two internal
USB headers provides a total of four
USB 2.0 connections (USB 2/3, 4/5)
for front panel support. A Type A USB
connector (USB 10 (3.0) and a vertical
USB connector (J-USB3-1) support 3.0
connections for front access (cables
not included). See the tables for pin
definitions.
PWR SMB
Pin Definitions
Power SMB (I2C) Connector
Power System Management Bus (I2C)
Connector (JPI2C1) monitors power
supply, fan and system temperatures.
See the table on the right for pin
definitions.
Universal Serial Bus (USB)
Pin#
Pin#
Definition
1
Clock
2
Data
3
PWR Fail
4
Ground
5
+3.3V
Backplane USB
(USB 0/1, 2/3)
Pin Definitions
Pin# Definition
USB 4, 6
Pin # Definition
1
+5V
1
+5V
1
+5V
2
PO-
2
PO-
2
PO-
3
PO+
3
PO+
3
PO+
4
Ground
4
Ground
4
Ground
5
NA
A System Management Bus header
for IPMI 2.0 is located at JIPMB1.
Connect the appropriate cable here
to use the IPMB I2C connection on
your system.
Pin#
Definition
1
Data
2
Ground
3
Clock
4
No Connection
5
USB 5
Pin # Definition
NC
5
Key
(NC= No connection)
USB (3.0) USB 10, USB 12/13 (3.0), JUSB3-1 Pin Definitions
Pin #
IPMB Header
Pin Definitions
IPMB
FP USB (4/5, 6)
Pin Definitions
Definition
Pin #
Definition
1
VBUS
2
SSRX-
3
SSRX+
4
Ground
5
SSTX-
6
SSTX+
7
GND DRAIN
8
D-
9
D+
Serial Ports
Serial COM) Port
Pin Definitions
Two COM connections (COM1 &
COM2) are located on the serverboard.
COM1 is located on the rear I/O panel.
COM2, located next to PCI-E Slot1
Pin #
is used to provide front access support. See the table on the right for pin
definitions.
Definition
Pin #
Definition
1
DCD
6
DSR
2
RXD
7
RTS
3
TXD
8
CTS
4
DTR
9
RI
5
Ground
10
N/A
PWR LED Connector
Pin Definitions
Power LED/Speaker
Pin Setting
Pins 1-3 of JD1 are used for power
LED indication, and pins 4-7 are for
the speaker. See the tables on the
right for pin definitions. Please note
that the speaker connector pins (4-7)
are used with an external speaker. If
you wish to use the onboard speaker,
you should close pins 6-7 with a cap.
Definition
Pin 1
JD1_PIN1
Pin 2
FP_PWR_LED
Pin 3
FP_PWR_LED
Speaker Connector
Pin Settings
Pin Setting
Definition
Pin 4
P5V
Pin 5
Key
Pin 6
R_SPKPIN_N
Pin 7
R_SPKPIN
LAN Ports
Pin Definitions
Ethernet Ports
Two Ethernet ports (LAN1/2) are
located on the I/O backplane. These
are 10 Gb ports on the 7048R-TRT
and 1 Gb ports on the 7048R-TR. In
addition, a dedicated IPMI LAN port,
located above the USB 0/1 ports on
the backplane. All these ports accept
RJ45 type cables.
Note: Please refer to the LED Indicator
Section for LAN LED information.
5-18
5-19
Pin# Definition
1
P2V5SB
10
SGND
2
TD0+
11
Act LED
3
TD0-
12
P3V3SB
4
TD1+
13
Link 100 LED (Yellow, +3V3SB)
5
TD1-
14
Link 1000 LED
(Yellow, +3V3SB)
6
TD2+
15
Ground
7
TD2-
16
Ground
8
TD3+
17
Ground
9
TD3-
18
Ground
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
CMOS Clear
Unit Identifier Switch/UID LED
Indicator
A Unit Identifier (UID) switch and an
LED indicator are provided on the
motherboard. The rear UID switch is
located next to the VGA port on the
backplane. The front UID switch is
located on pin 13 of the JF1 header.
The rear UID LED (LE1) is located
next to the UID switch and the front
UID LED is located on pin 7 on JF1.
When you press the UID switch, the
UID LED will be turned on. Press the
UID switch again to turn off the LED
indicator. The UID indicator provides
easy identification of a system unit that
may be in need of service.
JBT1 is used to clear CMOS (which will also clear any passwords). Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.
To clear CMOS,
UID Switch
Pin#
Definition
1
Ground
2
Ground
3
Button In
4
Ground
1. First power down the system and unplug the power cord(s).
2. With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver.
3. Remove the screwdriver (or shorting device).
UID LED
Status
4. Reconnect the power cord(s) and power on the system.
Color/State Status
Blue: On
Unit Identified
Note: Do not use the PW_ON connector to clear CMOS.
LAN Enable/Disable
Note: UID can also be triggered via
IPMI on the motherboard. For more
information on IPMI, please refer to
the IPMI User's Guide posted on our
website.
Use JPL1 to enable/disable the LAN
ports 1/2. See the table on the right
for jumper settings. The default setting
is Enabled.
LAN1/2 Enable/Disable
Jumper Settings
Jumper Setting Definition
Pins 1-2
Enabled (default)
Pins 2-3
Disabled
Watch Dog Enable/Disable
5-9 Jumper Settings
Explanation of Jumpers
To modify the operation of the
serverboard, jumpers can be used
to choose between optional settings.
Jumpers create shorts between two
pins to change the function of the connector. Pin 1 is identified with a square
solder pad on the printed circuit board.
See the serverboard layout pages for
jumper locations.
Note: On a two-pin jumper, "Closed"
means the jumper is on both pins and
"Open" means the jumper is either on
only one pin or completely removed.
5-20
Connector
Pins
3
2
1
Jumper
3
Setting
2
Jumper JWD controls the Watch Dog
function. Watch Dog is a system monitor that can reboot the system when a
software application hangs. Close pins
1-2 to to reset the system if an application hangs. Close pins 2-3 to generate
a non-maskable interrupt signal for the
application that hangs. See the table
on the right for jumper settings. Watch
Dog must also be enabled in BIOS.
Watch Dog
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Reset (default)
Pins 2-3
NMI
Open
Disabled
1
VGA Enable/Disable
JPG1 allows you to enable or disable
the VGA port. The default position is on
pins 1 and 2 to enable VGA. See the
table on the right for jumper settings.
5-21
VGA Enable/Disable
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
5-10 Onboard Indicators
Close pins 2 and 3 of jumper JPME2
to bypass SPI flash security and force
the system to operate in the Manufacturer Mode, which allows the user to
flash the system firmware from a host
server for system setting modifications.
See the table on the right for jumper
settings.
BIOS Recovery Enable (JBR1)
Close pins 1 and 2 of jumper JBR1 for
BIOS recovery. The default setting is
on pins 2 and 3 for normal operation.
See the table on the right for jumper
settings.
ME Mode Select
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Normal (Default)
Pins 2-3
Manufacture Mode
BIOS Recovery Jumper
Settings
Both Jumpers
Definition
Pins 1-2
Enabled
Pins 2-3
Normal
BMC Enable
Jumper JPB1 allows you to enable
the embedded Winbond BMC (Baseboard Management Controller) to
provide IPMI 2.O/KVM support on the
serverboard. See the table on the right
for jumper settings.
BMC Enable
Jumper Settings
Jumper Setting
Definition
Pins 1-2
BMC Enabled
Pins 2-3
Disabled
LAN LEDs
The Ethernet ports (located beside the
VGA port) have two LEDs. On each
port, one LED flashes to indicate activity while the other LED may be green,
amber or off to indicate the speed of
the connection. See the table on the
right for the functions associated with
the connection speed LED.
5-22
I2C to PCI-E Slots
Jumper Settings
Jumper Setting
Definition
Pins 1-2
Enabled
Pins 2-3
Disabled
LED Color
Definition
Off
10 Mb/s, 100 Mb/s or no
connection
Green
10 Gb/s (X10DRi-T only)
Amber
1 Gb/s
IPMI LAN
IPMI Dedicated LAN LEDs
Activity LED
Link LED
An additional Dedicated IPMI LAN is
also located on the I/O backplane.
The amber LED on the right indicates
activity, while the green LED on the
left indicates the speed of the connection. See the table at right for more
information.
IPMI LAN Link LED (Left) &
Activity LED (Right)
LED
Status
Definition
Link (Left)
Green: Solid
100 Mb/s
Activity
(Right)
Amber: Blinking
Active
Onboard PWR LED Indicator
LED Settings
Onboard Power LED (LE1)
An Onboard Power LED is located at
LE2. This LED Indicator is lit when
the system is on. Be sure to unplug
the power cable before removing or
adding any components. See the table
on the right for more details.
I2C Bus to PCI-Exp. Slots
Jumpers JI2C1 and JI2C2 allow you to
connect the System Management Bus
(I2C) to the PCI-Express slots. The
default setting is disabled. Both jumpers must be set to the same setting
See the table on the right for jumper
settings.
JLAN1/2 LED
(Connection Speed Indicator)
X8DT3-LN4/LN4F
Manufacturer Mode Select
BMC Heartbeat LED
A BMC Heartbeat LED is located at
LEDM1 on the serverboard. When
D1 is blinking, BMC is functioning
normally.
5-23
LED Color
Status
Off
System Off (PWR cable
not connected)
Green
System On
Green:
Flashing
Quickly
ACPI S1 State
Green:
Flashing
Slowly
ACPI S3 (STR) State
BMC Heartbeat LED
Status
Color/State
Green:
Blinking
Definition
BMC: Normal
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
5-11 SATA Ports
5-12 Installing Software
The Supermicro FTP site contains drivers and utilities for your system at ftp://ftp.
supermicro.com. Some of these must be installed, such as the chipset driver.
SATA 3.0 Ports
There are ten Serial ATA Ports, which
include six SATA supported by the
PCH C612 (I-SATA0 ~5) and four
SATA supported by the Intel SCU (SSATA0~3). See the table on the right
for pin definitions. The 7048R-TRT/TR
supports a total of eight 3.5" hot-swap
hard drives.
SATA Port
Pin Definitions
Pin#
Definition
Pin
Definition
1
Ground
2
TXP
3
TXN
4
Ground
5
RXN
6
RXP
7
Ground
After accessing the FTP site, go into the CDR_Images directory and locate the ISO
file for your motherboard. Download this file to create a CD/DVD of the drivers and
utilities it contains. (You may also use a utility to extract the ISO file if preferred.)
Another option is to go to the Supermicro website at http://www.supermicro.com/
products/. Find the product page for your motherboard here, where you may download individual drivers and utilities.
After creating a CD/DVD with the ISO files, insert the disk into the CD/DVD drive
on your system and the display shown in Figure 5-5 should appear.
Figure 5-5. SuperDoctor III Interface Display Screen (Health Information)
Note: Click the icons showing a hand writing on paper to view the readme files
for each item. Click the computer icons to the right of these items to install each
item (from top to the bottom) one at a time. After installing each item, you must
re-boot the system before moving on to the next item on the list. The bottom
icon with a CD on it allows you to view the entire contents of the CD.
5-24
5-25
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 5: Advanced Serverboard Setup
5-13 Onboard Battery
SuperDoctor® 5
The Supermicro SuperDoctor 5 is a program that functions in a command-line or
web-based interface in Windows and Linux operating systems. The program monitors system health information such as CPU temperature, system voltages, system
power consumption, fan speed, and provides alerts via email or Simple Network
Management Protocol (SNMP).
SuperDoctor 5 comes in local and remote management versions and can be used
with Nagios to maximize your system monitoring needs. With SuperDoctor 5 Management Server (SSM Server), you can remotely control power on/off and reset
chassis intrusion for multiple systems with SuperDoctor 5 or IPMI. SD5 Management Server monitors HTTP, FTP, and SMTP services to optimize the efficiency of
your operation.
Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfill. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.
Figure 5-7. Installing the Onboard Battery
Note: The default User Name and Password for SuperDoctor 5 is admin / admin.
OR
Figure 5-6. SuperDoctor 5 Interface Display Screen (Health Information)
Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfill. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.
Note: The SuperDoctor 5 program and User’s Manual can be downloaded from
the Supermicro web site at http://www.supermicro.com/products/nfo/sms_sd5.cfm.
5-26
5-27
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Notes
5-28
Chapter 6: Advanced Chassis Setup
Chapter 6
Advanced Chassis Setup
This chapter covers the steps required to install components and perform simple
maintenance on the SC745TQ-R920B chassis. Following the component installation
steps in the order given will eliminate most common problems. If some steps are
unnecessary, skip ahead to the step that follows. Refer to Chapter 2 for instructions
on installing the system as a 4U rackmount.
Tools Required: The only tool you will need is a Philips screwdriver.
6-1 Static-Sensitive Devices
Static electrical discharge can damage electronic com­ponents. To prevent damage
to any printed circuit boards (PCBs), it is important to handle them very carefully.
The following measures are generally sufficient to protect your equipment from
static discharge.
Precautions
•Use a grounded wrist strap designed to prevent static discharge.
•Touch a grounded metal object before removing any board from its antistatic
bag.
•Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or gold contacts.
•When handling chips or modules, avoid touching their pins.
•Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
•For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
Unpacking
The serverboard is shipped in antistatic packaging. When unpacking the board,
make sure the person handling it is static protected.
6-1
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 6: Advanced Chassis Setup
Figure 6-1. Chassis Front and Rear Views
USB Ports
Control Panel
5.25" Drive Bays (3)
6-2 Front Control Panel
The front control panel must be connected to the JF1 connector on the serverboard
to provide you with system status and alarm indications. A ribbon cable has bundled
these wires together to simplify this connection. Connect the cable from JF1 on the
serverboard (making sure the red wire plugs into pin 1) to the appropriate comnnector on the front control panel PCB (printed circuit board). Pull all excess cabling over
to the control panel side of the chassis. The LEDs on the control panel inform you
of system status -See Figure 6-2 for details. See Chapter 5 for details on JF1.
Figure 6-2. Front Control Panel LEDs
8 Hard Drive Bays
(behind locking bezel)
Power
Indicates power is being supplied to the system.
On the SC745TQ-R920B, this LED indicates hard drive
activity when flashing.
HDD
Power Supplies
NIC1
1
Indicates network activity on LAN port 1.
NIC2
2
Indicates network activity on LAN port 2
Rear Fans
Rear I/O Ports
6-2
Information LED
This LED will be solid blue when the UID function has
been activated. When flashing red it indicates a fan failure
and when solid red it indicates an overheat condition (see
Chapter 3 for details).
Power Fail
Indicates a power supply failure. This LED is functional
only when two power supply modules are installed in the
system.
PCI Slots
6-3
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
6-3 System Fans
Chapter 6: Advanced Chassis Setup
Removing the Air Shroud
Three 8-cm chassis cooling fans (located in the center of the chassis) provide cooling airflow while two 8-cm exhaust fans expel hot air from the chassis. The chassis
is also fitted with an air shroud to concentrate the flow of cooling air over the areas
of highest generated heat. The fans should all be connected to headers on the
serverboard (see Chapter 5). Each power supply module also has a cooling fan.
Fan Failure
Under most circumstances you will not need to remove the air shroud to perform
any service on the system. However, if you wish to temporarily remove it (the air
shroud should always be in place when the system is operating), please follow
this procedure.
1. Begin by depressing the tabs at the front and rear of the shroud to unlock it.
2. Lift the air shroud up and out of the chassis (see Figure 6-4).
Under normal operation, all three chassis fans, both exhaust fans and the
power supply fans run continuously. The chassis fans and the exhaust fans are
hot-swappable and can be replaced without powering down the system.
Accessing the Inside of the System
1. If rack mounted, first release the screws that secure the unit to the rack.
3. To reinstall, simply position the air shroud in its proper place and push it in
until you hear it click.
Figure 6-3. Removing a Chassis Fan
2. Grasp the two handles on either side and pull the unit straight out until it
locks (you will hear a "click").
3. There are two screws that secure the cover to the chassis - remove these
first.
4. Locate the latch on the top (side if tower) of the chassis - depress where it
says "push" then lift the latch to release the cover.
5. Lift the cover from the chassis to gain full access to the inside of the server.
Replacing Chassis Cooling Fans
1. First, remove the top/left chassis cover (see Chapter 2 for details on removing
the cover) to locate the fan that has stopped working.
Figure 6-4. Removing the Air Shroud
2. Depress the locking tab on the failed fan: on a chassis fan, push the tab on
the side of the housing inward, on the exhaust fan push down on the colored
tab. With the tab depressed, pull the unit straight out (see Figure 6-3). The
wiring for these fans has been designed to detach automatically.
3. Replace the failed fan with an identical one. Install it in the same position
and orientation as the one you removed; it should click into place when fully
inserted. Check that the fan is working then replace the top/left side chassis
panel.
6-4
6-5
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
6-4 Drive Bay Installation
Chapter 6: Advanced Chassis Setup
Figure 6-5. Removing a Drive Carrier
SATA Hard Drives
A total of eight 3.5" SATA drives may be housed in the SC745 chassis. The drive
IDs are preconfigured as 0 through 7 in order from bottom to top (or from left to right
if rackmounted). A bezel covers the drive area but does not need to be removed
to access the drives; simply swing open the bezel. If you wish to remove the bezel
piece, push on the three tabs on the inside of the left lip of the front chassis cover.
Then slightly swing out the same (left) side of the cover - about ½ inch only. Remove
by pushing on the open side of the cover to remove it from the chassis (do not try
to swing or pull it straight out after opening the left side).
The drives are mounted in drive carriers to simplify their installation and removal
from the chassis. These drives are hot-swappable, meaning they can be removed
and installed without powering down the system. The carriers also work to promote
proper airflow for the system. For this reason, even carriers without drives must
remain in the server.
Figure 6-6. Mounting a Drive in a Carrier
Warning: Regardless of how many drives are installed, all drive carriers must remain
in the drive bays to promote proper airflow.
Warning: Enterprise level hard disk drives are recommended for use in Supermicro
chassis and servers. For information on recommended HDDs, visit the Supermicro
website at http://www.supermicro.com/products/nfo/storage.cfm
Installing/Removing Hard Drives
1. To remove a carrier, first open the front bezel.
Warning: Use extreme caution when working around the SATA backplane. Do not
touch the backplane with any metal objects and make sure no cables touch the backplane or obstruct the airflow holes.
2. Push the release button located beside the drive LEDs (See Figure 6-5).
3. Swing the handle fully out and then use it to pull the unit straight out.
Note: Your operating system must have RAID support to enable the hot-swap
capability of the drives.
Mounting a Hard Drive in a Drive Carrier
SATA Backplane
The SATA drives plug into a backplane. SATA cables must be connected from the
serverboard to the appropriate connectors on the backplane to support eight SATA
drives.
1. Insert the drive into the carrier with the printed circuit board side facing down
so that the mounting holes align with those in the carrier.
2. Secure the drive to the carrier with four screws (see Figure 6-6).
6-6
6-7
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 6: Advanced Chassis Setup
Installing Components in the 5.25" Drive Bays
The 7048R-TR/7048R-TRT has two 5.25" drive bays. DVD-ROM drives can be
installed into these 5.25" drive bays.
1. First power down the system and then remove the top/left chassis cover to
access the drive components.
2. With the cover off, remove the two or four screws that secure the drive carrier
to the chassis (one side only) then push the entire empty drive carrier out
from the back.
Figure 6-7. Rotating the Storage Module
Adding a DVD-ROM Drive
1. Remove the guide plates (one on each side) from the empty drive carrier and
screw them into both sides of the DVD-ROM drive using the holes provided.
2. Slide the DVD-ROM into the bay and secure it to the chassis with the drive
carrier screws you first removed.
3. Attach the power and data cables to the drive.
Storage Module
Storage Module
Release Lever
4. Replace the top/left chassis cover before restoring power to the system.
Storage Module
If the 7048R-TR/7048R-TRT is to be used in a rack configuration, you must turn
the storage module 90 degrees. This can be done before, during, or after setup.
Rotating the Storage Module
1. Open the chassis cover.
2. Disconnect any cables from the storage module to any components in the
chassis.
3. Push the storage module release lever to unlock the storage module.
4. Grasp the external edges of the storage module and pull it from the chassis.
5. Turn the storage module 90 degrees (as illustrated).
6. Reinsert the module into the chassis and reconnect the cords.
6-8
6-9
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
6-5 Power Supply
The SuperServer 7048R-TR/7048R-TRT has a redundant 920 watt power supply
consisting of two power modules. Each power supply module has an auto-switching
capability, which enables it to automatically sense and operate at a 100V - 240V
input voltage.
Power Supply Failure
If either of the two power supply modules fail, the other module will take the full load
and allow the system to continue operation without interruption. The PWR Fail LED
will illuminate and remain on until the failed unit has been replaced. Replacement
units can be ordered directly from Supermicro (see contact information in the Preface). The hot-swap capability of the power supply modules allows you to replace
the failed module without powering down the system.
Replacing the Power Supply
You do not need to shut down the system to replace a power supply module. The
redundant feature will keep the system up and running while you replace the failed
hot-swap unit. Replace with the exact same model (see Appendix B).
1. Unplug the AC power cord from the failed power supply module.
2. Remove the chassis left-top cover as described in Section 6-3.
3. Remove the screws that secure the power module to the chassis then pull it
completely out.
4. Replace the failed unit with another unit of the exact same part number (see
Appendix).
5. Gently but firmly push the new unit all the way into the open bay.
6. Secure it to the chassis using the screws you previously removed.
7. Finish by replacing the chassis left/top cover and then plugging the AC power
cord back into the new module you just added.
6-10
Chapter 7: BIOS
Chapter 7
BIOS
7-1 Introduction
This chapter describes the AMI BIOS setup utility for the X10DRi/X10DRi-T. The
ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter
describes the basic navigation of the AMI BIOS setup utility screens.
Note: For AMI BIOS recovery, please refer to the UEFI BIOS Recovery
Instructions in Appendix C.
Starting BIOS Setup Utility
To enter the AMI BIOS setup utility screens, press the <Delete> key while the
system is booting up.
Note: In most cases, the <Delete> key is used to invoke the AMI BIOS
setup screen. There are a few cases when other keys are used, such as
<F1>, <F2>, etc.
Each main BIOS menu option is described in this manual. The AMI BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be configured. Grayed-out options cannot be configured. Options in blue can be
configured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it.
Note: the AMI BIOS has default text messages built in. Supermicro retains
the option to include, omit, or change any of these text messages.
The AMI BIOS setup utility uses a key-based navigation system called "hot keys."
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F4>, <Enter>, <Esc>, arrow
keys, etc.
Note: Options printed in Bold are default settings.
How To Change the Configuration Data
The configuration data that determines the system parameters may be changed by
entering the AMI BIOS setup utility. This setup utility can be accessed by pressing
<Del> at the appropriate time during system boot.
7-1
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
How to Start the Setup Utility
Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS setup utility. From the main menu, you can access the other setup
screens. An AMI BIOS identification string is displayed at the left bottom corner of
the screen, below the copyright message.
Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event
shall Supermicro be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS update. If you have to update the BIOS, do not shut down
or reset the system while the BIOS is updating. This is to avoid possible boot failure.
Chapter 7: BIOS
The following Main menu items will be displayed:
System Date/System Time
Use this option to change the system date and time. Highlight System Date or
System Time using the arrow keys. Enter new values using the keyboard. Press the
<Tab> key or the arrow keys to move between fields. The date must be entered in
Day MM/DD/YYYY format. The time is entered in HH:MM:SS format.
Note: The time is in the 24-hour format. For example, 5:30 P.M. appears
as 17:30:00.
Supermicro X10DRi
Version: This item displays the version of the BIOS ROM used in the system.
7-2 Main Setup
When you first enter the AMI BIOS setup utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS setup screen is shown below.
Build Date: This item displays the date when the version of the BIOS ROM
used in the system was built.
Memory Information
Total Memory: This item displays the total size of memory available in the
system.
Memory Speed: This item displays the default speed of the memory modules
installed in the system.
7-2
7-3
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
7-3 Advanced Setup Configurations
Use the arrow keys to select Advanced setup and press <Enter> to access the
submenu items:
Chapter 7: BIOS
Wait For 'F1' If Error
Select Enabled to force the system to wait until the 'F1' key is pressed if an error
occurs. The options are Disabled and Enabled.
Interrupt 19 Capture
Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Immediate, the ROM BIOS of the host adaptors will "capture" Interrupt 19 at bootup immediately and allow the drives that are attached to these host
adaptors to function as bootable disks. If this item is set to Postponed, the ROM
BIOS of the host adaptors will not capture Interrupt 19 immediately and allow the
drives attached to these adaptors to function as bootable devices at bootup. The
options are Immediate and Postponed.
Re-try Boot
When EFI Boot is selected, the system BIOS will automatically reboot the system
from an EFI boot device after its initial boot failure. Select Legacy Boot to allow
the BIOS to automatically reboot the system from a Legacy boot device after its
initial boot failure. The options are Disabled, Legacy Boot, and EFI Boot.
Warning: Take Caution when changing the Advanced settings. An incorrect value, a
very high DRAM frequency or an incorrect BIOS timing setting may cause the system
to malfunction. When this occurs, restore the setting to the manufacture default setting.
Boot
Power Configuration
Watch Dog Function
Select Enabled to allow the Watch Dog timer to reboot the system when it is inactive for more than 5 minutes. The options are Enabled and Disabled.
Feature
Power Button Function
Quiet Boot
Use this feature to select the screen display between POST messages or the OEM
logo at bootup. Select Disabled to display the POST messages. Select Enabled
to display the OEM logo instead of the normal POST messages. The options are
Enabled and Disabled.
This feature controls how the system shuts down when the power button is pressed.
Select 4 Seconds Override for the user to power off the system after pressing and
holding the power button for 4 seconds or longer. Select Instant Off to instantly
power off the system as soon as the user presses the power button. The options
are 4 Seconds Override and Instant Off.
AddOn ROM Display Mode
Restore on AC Power Loss
Use this item to set the display mode for the Option ROM. Select Keep Current to
use the current AddOn ROM display setting. Select Force BIOS to use the Option
ROM display mode set by the system BIOS. The options are Force BIOS and
Keep Current.
Use this feature to set the power state after a power outage. Select Power-Off for
Bootup Num-Lock
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last power state before a power loss. The options are Power-On,
Stay-Off and Last State.
Use this feature to set the Power-on state for the Numlock key. The options are
Off and On.
7-4
7-5
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
CPU
Configuration
Chapter 7: BIOS
The following items will be display:
PCI-E Port Link Status
North Bridge
PCI-E Port Link Max
This feature allows the user to configure the settings for the Intel North Bridge.
PCI-E Port Link Speed
PCI-E Port L0s Exit Latency
IIO Configuration
EV DFX (Device Function On-Hide) Features
When this feature is set to Enable, the EV_DFX Lock Bits that are located on a
processor will always remain clear during electric tuning. The options are Disable and Enable.
Use this feature to set the length of time required for the port specified by the
user to complete the transition from L0s to L0. The default setting is 4uS - 8uS.
PCI-E Port L1 Exit Latency
Use this feature to set the length of time required for the port specified by the
user to complete the transition from L1 to L0. The default setting is <1uS, 1uS 2uS, 2uS - 4uS, 4uS - 8uS, 8uS - 16uS, 16uS - 32uS, 32uS - 64uS, and >64uS.
IIO0 Configuration
Fatal Err (Error) Over
IOU2 (II0 PCIe Port 1)
Select Enable to force fatal error prorogation to the II0 core error logic for the
port specified by the user. The options are Disable and Enable.
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4, x8, and Auto.
IOU0 (II0 PCIe Port 2)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
IOU1 (II0 PCIe Port 3)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
No PCIe Port Active ECO
Use this feature to select a workaround setting to implement the engineeringchange order (ECO) on the system when the PCI ports specified by the user
are not active. The options are PCU Squelch exit ignore option and Reset the
SQ FLOP by CSR option.
Non-Fatal Err (Error) Over
Select Enable to force non-fatal error prorogation to the II0 core error logic for
the port specified by the user. The options are Disable and Enable.
Corr Err (Correctable Error) Over
Select Enable to force correctable error prorogation to the II0 core error logic for
the port specified by the user. The options are Disable and Enable.
L0s Support
When this item is set to Disable, II0 will not put its transmitter in the L0s state.
The default setting is Disable.
IIO1 Configuration
IOU2 (II0 PCIe Port 1)
Socket 0 PCIeD00F0 - Port 0/DMI
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4, x8, and Auto.
Link Speed
IOU0 (II0 PCIe Port 2)
This item configures the link speed of a PCI-E port specified by the user. The
options are Gen 1 (Generation 1) (2.5 GT/s) and Gen 2 (Generation 2).
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
PCI-E Port DeEmphasis
IOU1 (II0 PCIe Port 3)
This item configures the De-Emphasis Control (LANKCON2 [6]) setting for this
computer. The options are -6.0 dB and -3.5 dB.
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.
7-6
7-7
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 7: BIOS
No PCIe Port Active ECO
Coherency Support (Isoch)
Use this feature to select a workaround setting to implement the engineeringchange order (ECO) on the system when PCI ports are not active. The options
Select Enable for the Iscoh VT-d engine to pass through ATS to enhance system
performance. The options are Enable and Disable.
are PCU Squelch exit ignore option and Reset the SQ FLOP by CSR option.
QPI (Quick Path Interconnect) Configuration
IOAT Configuration
The following QPI information will be displayed:
Enable I/OAT
•Number of CPU
Select Enable to enable Intel I/OAT (I/O Acceleration Technology), which significantly reduces CPU overhead by leveraging CPU architectural improvements
and freeing the system resource for other tasks. The options are Enable and
Disable.
•Number of II0
No Snoop
•Current QPI Link Frequency: This item displays the frequency of the QPI
Select Enable to support no-snoop mode for each CB device. The options are
Disable and Enable.
Relaxed Ordering
Select Enable to enable Relaxed Ordering support which will allow certain transactions to violate the strict-ordering rules of PCI and to be completed prior to
other transactions that have already been enqueued. The options are Disable
and Enable.
•Current QPI Link Speed: This item displays the current QPI Link speed.
Link.
•QPI Global MMIO Low Base / Limit
•QPI Global MMIO High Base / Limit
•QPI PCI-E Configuration Base / Siz (Size)
Link Speed Mode
 Intel VT for Directed I/O (VT-d)
Intel VT for Direct I/O (VT-d)
Use this feature to select data transfer speed for QPI Link connections. The options are Fast and Slow.
Link Frequency Select
Intel® VT for Directed I/O (VT-d)
Select Enable to use Intel Virtualization Technology support for Direct I/O VT-d
support by reporting the I/O device assignments to the VMM (Virtual Machine
Monitor) through the DMAR ACPI tables. This feature offers fully-protected I/O
resource sharing across Intel platforms, providing greater reliability, security and
availability in networking and data-sharing. The options are Enable and Disable.
Interrupt Remapping
Select Enable for Interrupt Remapping support to enhance system performance.
The options are Enable and Disable.
Coherency Support (Non-Isoch)
Select Enable for the Non-Iscoh VT-d engine to pass through DMA (Direct
Memory Access) to enhance system performance. The options are Enable and
Disable.
7-8
Use this feature to select the desired QPI frequency. The options are 6.4 GT/s,
8.0 GT/s, 9.6 GT/s, Auto, and Auto Limited.
Link L0p Enable
Select Enable to enable Link L0p. The options are Disable and Enable.
Link L1 Enable
Select Enable to enable Link L1 (Level 1 link). The options are Disable and
Enable.
Isoc Mode
Select Enabled to enable Isochronous support to meet QoS (Quality of Service)
requirements. This feature is especially important for Virtualization Technology.
The options are Enable and Disable.
7-9
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 7: BIOS
Memory Configuration
Rank Interleaving
Enforce POR
Use this item to select a rank memory interleaving method. The options are Auto,
1-Way, 2-Way, 4-Way, and 8-Way.
Select Enable to enforce POR restrictions on DDR4 frequency and voltage programming. The options are Auto, Enforce POR, Disabled and Enforce Stretch
Goals.
Memory Frequency
Use this feature to set the maximum memory frequency for onboard memory
modules. The options are Auto, 1333, 1400, 1600, 1800, 1867, 2000, 2133,
2200, 2400, 2600, 2667, and Reserved (Do not select Reserved).
A7 Mode
Select Enabled to support the A7 (Addressing) mode to improve memory performance. The options are Enable and Disable.
DIMM Information
This item displays the status of a DIMM module specified by the user.
ECC Support
•P1 DIMMA1
Select Enable to enable Error Checking & Correction (ECC) support for onboard
memory modules. The options are Auto, Enable and Disable.
•P1 DIMMB1
•P1 DIMMC1
Data Scrambling
Select Enabled to enable data scrambling to enhance system performance and
data integrity. The options are Auto, Disabled and Enabled.
Enable ADR
Select Enabled for ADR (Automatic Diagnostic Repository) support to enhance
memory performance. The options are Enabled and Disabled.
DRAM RAPL (Running Average Power Limit) Baseline
Use this feature to set the run-time power-limit baseline for DRAM modules. The
options are Disable, DRAM RAPL Mode 0, and DRAM RAPL Mode 1.
Set Throttling Mode
Throttling improves reliability and reduces power consumption in the processor via automatic voltage control during processor idle states. The options are
Disabled and CLTT (Closed Loop Thermal Throttling).
Socket Interleave Below 4GB
Select Enabled for the memory above the 4G Address space to be split between
two sockets. The options are Enable and Disable.
Channel Interleaving
Use this item to set DIMM channel interleaving mood. The options are Auto,
1-Way Interleave, 2-Way Interleave, 3-Way Interleave, and 4-Way Interleave.
•P1 DIMMD1
Memory RAS (Reliability_Availability_Serviceability)
Configuration
Use this submenu to configure the following Memory RAS settings.
RAS Mode
When Disable is selected, RAS is not supported. When Mirror is selected, the
motherboard maintains two identical copies of all data in memory for data backup.
When Lockstep is selected, the motherboard uses two areas of memory to run
the same set of operations in parallel to boost performance. The options are
Disable, Mirror, and Lockstep Mode.
Lockstep x4 DIMMs
Select Enable to enable Lockstep support for x4 DIMM modules. The options
are Auto, Disabled, and Enabled.
Memory Rank Sparing
Select Enable to enable memory-sparing support for memory ranks to improve
memory performance. The options are Disabled and Enabled.
Patrol Scrub
Patrol Scrubbing is a process that allows the CPU to correct correctable memory
errors detected on a memory module and send the correction to the requestor
(the original source). When this item is set to Enabled, the IO hub will read and
7-10
7-11
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
write back one cache line every 16K cycles, if there is no delay caused by internal
processing. By using this method, roughly 64 GB of memory behind the IO hub
will be scrubbed every day. The options are Enable and Disable.
Patrol Scrub Interval
This feature allows you to decide how many hours the system should wait before the next complete patrol scrub is performed. Use the keyboard to enter a
value from 0-24.
Demand Scrub
Demand Scrubbing is a process that allows the CPU to correct correctable
memory errors found on a memory module. When the CPU or I/O issues a
demand-read command, and the read data from memory turns out to be a
correctable error, the error is corrected and sent to the requestor (the original
source). Memory is updated as well. Select Enable to use Demand Scrubbing
for ECC memory correction. The options are Enable and Disable.
Device Tagging
Select Enable to support device tagging. The options are Disable and Enable.
Chapter 7: BIOS
XHCI Hand-Off
This is a work-around solution for operating systems that do not support XHCI (Extensible Host Controller Interface) hand-off. The XHCI ownership change should be
claimed by the XHCI driver. The settings are Enabled and Disabled.
EHCI Hand-Off
This item is for operating systems that do not support Enhanced Host Controller
Interface (EHCI) hand-off. When this item is enabled, EHCI ownership change will
be claimed by the EHCI driver. The settings are Enabled and Disabled.
USB Mass Storage Driver Support
Select Enabled for USB mass storage device support. The options are Disabled
and Enabled.
Port 60/64 Emulation
Select Enabled for I/O port 60h/64h emulation support, which in turn, will provide
complete legacy USB keyboard support for the operating systems that do not support legacy USB devices. The options are Disabled and Enabled.
USB Transfer Time-outs:
South
Bridge Configuration
The following South Bridge information will display:
USB
Configuration
•USB Configuration
USB Transfer Time-out
This feature is used to set the USB time-out value so that the tasks of USB control,
bulk, and interrupt transfer can be performed during the time-out period. The settings
are 1 second, 5 seconds, 10 seconds, and 20 Seconds.
Device Reset Time-out
•USB Module Version
This feature is used to set the time-out value for the USB mass storage device
before a start commend is issued to this device. This will provide the time needed
for the system to detect the presence of the device. The options are 10 Seconds,
20 Seconds, 30 Seconds and 40 Seconds.
•USB Devices
Legacy USB Support
Device Power-up Delay
Select Enabled to support onboard legacy USB devices. Select Auto to disable
legacy support if there are no legacy USB devices present. Select Disable to have
all USB devices available for EFI applications only. The options are Enabled,
Disabled and Auto.
Use this feature to set the maximum time allowed for a USB device to wait before
it properly reports itself to the host controller. The options are Auto and Manual.
USB 3.0 Support
Select Enabled for USB 3.0 support. The options are Smart Auto, Auto, Enabled,
Disabled and Manual.
7-12
7-13
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
SATA
Configuration
Chapter 7: BIOS
Port 0 ~ Port 5 SATA Device Type
When this submenu is selected, AMI BIOS automatically detects the presence of
the SATA devices that are supported by the Intel PCH chip and displays the following items:
SATA Controller
This item enables or disables the onboard SATA controller supported by the Intel
PCH chip. The options are Enabled and Disabled.
Configure SATA as
Select IDE to configure a SATA drive specified by the user as an IDE drive. Select
AHCI to configure a SATA drive specified by the user as an AHCI drive. Select
RAID to configure a SATA drive specified by the user as a RAID drive. The options
are IDE, AHCI, and RAID.
*If the item above "Configure SATA as" is set to AHCI, the following items
will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
SATA Port 0~ Port 5
This item displays the information detected on the installed SATA drive on the
particular SATA port.
•Model number of drive and capacity
•Software Preserve Support
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure SATA as" is set to IDE, the following items
will display:
Serial ATA Port 0~ Port 5
This item indicates that a SATA port specified by the user is not installed or not
present.
Port 0 ~ Port 5 SATA Device Type (Available when a SATA port is
detected)
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure SATA as" is set to RAID, the following items
will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
SATA RAID Option ROM/UEFI Driver
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy
driver for system boot. The options are Disabled, EFI, and Legacy.
Serial ATA Port 0~ Port 5
Port 0~ Port 5
Select Enabled to enable a SATA port specified by the user. The options are
Disabled and Enabled.
This item displays the information detected on the installed SATA drives on the
particular SATA port.
•Model number of drive and capacity
•Software Preserve Support
Port 0 ~ Port 5 Hot Plug
Select Enabled to enable hot-plugging support for a port specified by the user,
which will allow the user to replace a SATA disk drive installed on this port without
shutting down the system. The options are Enabled and Disabled.
Port 0 ~ Port 5 Spin Up Device
Port 0~ Port 5
Select Enabled to enable a SATA port specified by the user. The options are
Disabled and Enabled.
On an edge detect from 0 to 1, set this item to allow the PCH to initialize the
device. The options are Enabled and Disabled.
7-14
7-15
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
•Software Preserve Support
Port 0 ~ Port 5 Hot Plug
Select Enabled to enable hot-plugging support for a port specified by the user,
which will allow the user to replace a SATA disk drive installed on this port without
shutting down the system. The options are Enabled and Disabled.
Port 0 ~ Port 5 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
Port 0 ~ Port 5 SATA Device Type
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
sSATA
Chapter 7: BIOS
Configuration
When this submenu is selected, AMI BIOS automatically detects the presence of
the SATA devices that are supported by the PCH-sSATA controller and displays
the following items:
sSATA Controller
This item enables or disables the onboard SATA controller supported by the Intel
PCH-sSATA controller. The options are Enabled and Disabled.
Configure sSATA as
Select IDE to configure an sSATA drive specified by the user as an IDE drive. Select
AHCI to configure an sSATA drive specified by the user as an AHCI drive. Select
RAID to configure an sSATA drive specified by the user as a RAID drive. The options are IDE, AHCI, and RAID.
*If the item above "Configure sSATA as" is set to AHCI, the following items
will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
sSATA Port 0~ Port 3
This item displays the information detected on the installed on the sSATA port.
specified by the user.
sSATA Port 0~ Port 3
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
sSATA Port 0 ~ Port 3 Hot Plug
Select Enabled to enable hot-plugging support for a port specified by the user,
which will allow the user to replace a sSATA disk drive installed on this port
without shutting down the system. The options are Enabled and Disabled.
sSATA Port 0 ~ Port 3 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
Port 0 ~ Port 3 sSATA Device Type
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to IDE, the following items
will display:
sSATA Port 0~ Port 3
This item indicates that an sSATA port specified by the user is not installed or
not detected.
Port 0 ~ Port 3 sSATA Device Type (Available when a SATA port is
detected)
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to RAID, the following items
will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link to a low power state when
the I/O is inactive for an extended period of time, and the power state will return
to normal when the I/O becomes active. The options are Enabled and Disabled.
•Model number of drive and capacity
7-16
7-17
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
sSATA RAID Option ROM/UEFI Driver
Chapter 7: BIOS
•ME Firmware Status #2
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy
driver for system boot. The options are Disabled, EFI, and Legacy.
•Current State
sSATA Port 0~ Port 3
•Error Code
This item displays the information detected on the installed sSATA drives on the
particular sSATA port.
•Model number of drive and capacity
•Software Preserve Support
Altitude
This feature indicates the altitude of the platform this machine is located above the
sea level. The value is shown in meters. If the value is unknown, enter the number
"80000000".
MCTP (Management Component Transport Protocol) Bus Owner
sSATA Port 0~ Port 3
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
This feature indicates the location of the MCTP Bus owner. Enter 0s to all fields to
disable the MCTP Bus owner
sSATA Port 0 ~ Port 3 Hot Plug
PCIe/PCI/PnP Configuration
This feature designates this port for hot plugging. Set this item to Enabled for
hot-plugging support, which will allow the user to replace an sSATA drive without
shutting down the system. The options are Enabled and Disabled.
The following PCI information will be displayed:
•PCI Bus Driver Version
sSATA Port 0 ~ Port 3 Spin Up Device
•PCI Latency Timer
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
PCI Latency Timer
Port 0 ~ Port 3 sSATA Device Type
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
Use this item to configure the PCI latency timer for a device installed on a PCI bus.
Select 32 to set the PCI latency timer to 32 PCI clock cycles. The options are 32,
64, 96, 128, 160, 192, 224 and 248 (PCI Bus Clocks).
VGA Palette Snoop
This feature displays the following system ME configuration settings.
Select Enabled to support VGA palette register snooping which will allow a PCI
card that does not contain its own VGA color palette to examine a video card palette and mimic it for proper color display. The options are Disabled and Enabled.
•General ME Configuration
PERR# Generation
Server ME (Management Engine) Configuration
•Operational Firmware Version
Select Enabled to allow a PCI device to generate a PERR (PCI/PCI-E Parity Error)
number for a PCI bus error event. The options are Enabled and Disabled.
•Recovery Firmware Version
SERR# Generation
•ME Firmware Features
Select Enabled to allow a PCI device to generate an SERR (System Error) number
for a PCI bus error event. The options are Enabled and Disabled.
•ME Firmware Status #1
7-18
7-19
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 7: BIOS
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
Onboard LAN Option ROM Type
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G
Address. The options are Enabled and Disabled.
Select Enabled to enable Option ROM support to boot the computer using a device
installed on the slot specified by the user. The options are Legacy and EFI.
SR-IOV (Available if the system supports Single-Root Virtualization)
Onboard LAN1 Option ROM/Onboard LAN2 Option ROM
Select Enabled for Single-Root IO Virtualization support. The options are Enabled
and Disabled.
Use this option to select the type of device installed in LAN Port1 or LAN Port2
used for system boot. The default setting for LAN1 Option ROM is PXE, and the
default setting for LAN2 Option ROM is Disabled.
Maximum Payload
Select Auto for the system BIOS to automatically set the maximum payload value for
a PCI-E device to enhance system performance. The options are Auto, 128 Bytes,
256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
VGA Priority
Maximum Read Request
Network Stack
Select Auto for the system BIOS to automatically set the maximum size for a read
request for a PCI-E device to enhance system performance. The options are Auto,
128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible Firmware Interface) for network stack support. The options are
Enabled and Disabled.
ASPM Support
Super
Use this item to set the Active State Power Management (ASPM) level for a PCI-E
device. Select Auto for the system BIOS to automatically set the ASPM level based
on the system configuration. Select Disabled to disable ASPM support. The options
are Disabled, Auto and Force L0s.
Warning: Enabling ASPM support may cause some PCI-E devices to fail!
Use this item to select the graphics device to be used as the primary video display
for system boot. The options are Onboard and Offboard.
IO Configuration
Super IO Chip AST2400
Serial Port 1 Configuration/Serial Port 2 Configuration
Serial Port 1/Serial Port 2
Select Enabled to enable the onboard serial port specified by the user. The options
are Enabled and Disabled.
MMIOHBase
Use this item to select the base memory size according to memory-address mapping for the IO hub. The base memory size must be between 4032G to 4078G. The
options are 56T, 48T, 24T, 512G, and 256G.
MMIO High Size
Use this item to select the high memory size according to memory-address mapping
for the IO hub. The options are 256G, 128G, 512G, and 1024G.
CPU1 Slot 1 PCI-E x8 (OPROM)/CPU1 Slot 2 PCI-E x16 (OPROM)/CPU1 Slot
3 PCI-E x8 (OPROM)/CPU2 Slot 4 PCI-E x16 (OPROM)/CPU2 Slot 5 PCI-E x8
(OPROM)//CPU2 Slot 6 PCI-E x16 (OPROM)
Select Enabled to enable Option ROM support to boot the computer using a device installed on the slot specified by the user. The options are Disabled, Legacy
and EFI.
7-20
Device Settings
This item displays the base I/O port address and the Interrupt Request address of
a serial port specified by the user.
Change Port 1 Settings/Change Port 2 Settings
This feature specifies the base I/O port address and the Interrupt Request address
of Serial Port 1 or Serial Port 2. Select Auto for the BIOS to automatically assign
the base I/O and IRQ address to a serial port specified.
The options for Serial Port 1 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12); (IO=3E8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12).
The options for Serial Port 2 are Auto, (IO=2F8h; IRQ=3), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12); (IO=3E8h; IRQ=3, 4, 5,
6, 7, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12).
7-21
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Device Mode
Use this feature to configure SUART clock source settings. The options are
24MHz/13 and 24MHz.
Serial Port 2 Attribute
Select SOL to use COM Port 2 as a Serial_Over_LAN (SOL) port for console redirection. The options are COM and SOL.
Serial
Port Console Redirection
Chapter 7: BIOS
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.
Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.
Flow Control
COM 1 Console Redirection
Console Redirection
Select Enabled to enable COM Port 1 for Console Redirection, which will allow a
client machine to be connected to a host machine at a remote site for networking.
The options are Enabled and Disabled.
*If the item above set to Enabled, the following items will become available
for configuration:
Use this item to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start sending data when the
receiving buffer is empty. The options are None and Hardware RTS/CTS.
VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100
terminals. The options are Enabled and Disabled.
Console Redirection Settings
Recorder Mode
Terminal Type
Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.
This feature allows the user to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to
add color and function key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters
into one or more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Bits Per second
Use this item to set the transmission speed for a serial port used in Console
Redirection. Make sure that the same speed is used in the host computer and the
client computer. A lower transmission speed may be required for long and busy
lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Use this feature to set the data transmission size for Console Redirection. The
options are 7 (Bits) and 8 (Bits).
Parity
A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
7-22
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.
Legacy OS Redirection Resolution
Use this item to select the number of rows and columns used in Console Redirection for legacy OS support. The options are 80x24 and 80x25.
Putty KeyPad
This feature selects Function Keys and KeyPad settings for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX,
XTERMR6, SCO, ESCN, and VT400.
Redirection After BIOS Post
Use this feature to enable or disable legacy Console Redirection after BIOS
POST. When the option-Bootloader is selected, legacy Console Redirection is
disabled before booting the OS. When the option- Always Enable is selected,
legacy Console Redirection remains enabled upon OS bootup. The options are
Always Enable and Bootloader.
7-23
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
SOL/COM2
Chapter 7: BIOS
Flow Control
Console Redirection
Select Enabled to use the SOL port for Console Redirection. The options are
Enabled and Disabled.
*If the item above set to Enabled, the following items will become available
for user's configuration:
SOL/COM2 Console Redirection Settings
Use this feature to specify how the host computer will exchange data with the client
computer, which is the remote computer used by the user.
Terminal Type
Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color
and function key support. Select ANSI to use the Extended ASCII Character Set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Bits Per second
Use this feature to set the transmission speed for a serial port used in Console
Redirection. Make sure that the same speed is used in the host computer and the
client computer. A lower transmission speed may be required for long and busy
lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Use this feature to set the data transmission size for Console Redirection. The
options are 7 (Bits) and 8 (Bits).
Parity
A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.
Use this feature to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start data-sending when the
receiving buffer is empty. The options are None and Hardware RTS/CTS.
VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100
terminals. The options are Enabled and Disabled.
Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.
Legacy OS Redirection Resolution
Use this feature to select the number of rows and columns used in Console
Redirection for legacy OS support. The options are 80x24 and 80x25.
Putty KeyPad
This feature selects Function Keys and KeyPad settings for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX,
XTERMR6, SCO, ESCN, and VT400.
Redirection After BIOS Post
Use this feature to enable or disable legacy Console Redirection after BIOS
POST. When this feature is set to Bootloader, legacy Console Redirection is
disabled before booting the OS. When this feature is set to Always Enable,
legacy Console Redirection remains enabled upon OS boot. The options are
Always Enable and Bootloader.
Serial Port for Out-of-Band Management/Windows Emergency
Management Services (EMS)
The submenu allows the user to configure Console Redirection settings to support Out-of-Band Serial Port management.
Stop Bits
Console Redirection
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.
Select Enabled to use a COM port selected by the user for EMS Console Redirection. The options are Enabled and Disabled.
7-24
7-25
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 7: BIOS
*If the item above set to Enabled, the following items will become available
for user's configuration:
Trusted Computing (Available when a TPM device is
installed and detected by the BIOS)
Out-of-Band Management Port
Configuration
The feature selects a serial port in a client server to be used by the Windows
Emergency Management Services (EMS) to communicate with a remote host
server. The options are COM1 Console Redirection and COM2/SOL Console
Redirection.
Security Device Support
Terminal Type
Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII character set. Select VT100+ to add color
and function key support. Select ANSI to use the extended ASCII character set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
If this feature and the TPM jumper on the motherboard are both set to Enabled,
onboard security devices will be enabled for TPM support to enhance data integrity
and network security. Please reboot the system for a change on this setting to take
effect. The options are Enabled and Disabled.
TPM State
Select Enabled to use TPM (Trusted Platform Module) settings to enhance system
data security. Please reboot your system for any change on the TPM state to take
effect. The options are Disabled and Enabled.
Pending Operation
Bits Per Second
This item sets the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in both host computer and the client
computer. A lower transmission speed may be required for long and busy lines.
The options are 9600, 19200, 57600, and 115200 (bits per second).
Use this item to schedule a TPM-related operation to be performed by a security
device for system data integrity. Your system will reboot to carry out a pending TPM
operation. The options are None, Enable Take Ownership, Disable Take Ownership, and TPM Clear.
Note: Your system will reboot to carry out a pending TPM operation.
Flow Control
Use this item to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop data-sending when
the receiving buffer is full. Send a "Start" signal to start data-sending when
the receiving buffer is empty. The options are None, Hardware RTS/CTS, and
Software Xon/Xoff.
Current Status Information
This item displays the status of the TPM support on this motherboard.
The setting for each these features is displayed:
Data Bits, Parity, Stop Bits
7-26
7-27
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
ACPI
Chapter 7: BIOS
7-4 Event Logs
Settings
Use this feature to configure Event Log settings.
WHEA Support
Select Enabled to support the Windows Hardware Error Architecture (WHEA) platform and provide a common infrastructure for the system to handle hardware errors
within the Windows OS environment to reduce system crashes and to enhance
system recovery and health monitoring. The options are Enabled and Disabled.
High Precision Timer
Select Enabled to activate the High Precision Event Timer (HPET) that produces
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does in
synchronizing multimedia streams, providing smooth playback and reducing the dependency on other timestamp calculation devices, such as an x86 RDTSC Instruction embedded in the CPU. The High Performance Event Timer is used to replace
the 8254 Programmable Interval Timer. The options are Enabled and Disabled.
NUMA Support (Available when the OS supports this feature)
Select Enabled to enable Non-Uniform Memory Access support to enhance system
performance. The options are Enabled and Disabled.
COD Enable (Available when the OS and the CPU support this feature)
Select Enabled for Cluster-On-Die support to enhance system performance in cloud
computing. The options are Enabled, Disabled and Auto.
Change SMBIOS Event Log Settings
This feature allows the user to configure SMBIOS Event settings.
Enabling/Disabling Options
SMBIOS Event Log
Select Enabled to enable SMBIOS (System Management BIOS) Event Logging
during system boot. The options are Enabled and Disabled.
iSCSI Configuration
This item displays iSCSI configuration information:
iSCSI Initiator Name
This item displays the name of the iSCSI Initiator, which is a unique name used
in the world. The name must use the IQN format. The following actions can also
be performed:
Add an Attempt
Runtime Error Logging Support
Select Enabled to support Runtime Error Logging. The options are Enabled and
Disabled. If this item is set to Enable, the following item will be available for configuration:
Memory Corrected Error Enabling (Available when the item above-Runtime
Error Logging Support is set to Enable)
Delete Attempts
Select Enabled for the BIOS to correct a memory error if it is correctable. The options are Enabled and Disabled.
Change Attempt Order
PCI-Ex (PCI-Express) Error Enable
Select Enabled for the BIOS to correct errors occurred in the PCI-E slots. The options are Enabled and Disabled.
7-28
7-29
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Memory Correctable Error Threshold
Use this item to enter the threshold value for correctable memory errors. The default
setting is 10.
Chapter 7: BIOS
7-5 IPMI
Use this feature to configure Intelligent Platform Management Interface (IPMI)
settings.
Erasing Settings
Erase Event Log
Select Enabled to erase all error events in the SMBIOS (System Management BIOS)
log before an event logging is initialized at bootup. The options are No and Yes.
When Log is Full
Select Erase Immediately to immediately erase all errors in the SMBIOS event log
when the event log is full. Select Do Nothing for the system to do nothing when
the SMBIOS event log is full. The options are Do Nothing and Erase Immediately.
SMBIOS Event Log Standard Settings
Log System Boot Event
Select Enabled to log system boot events. The options are Disabled and Enabled.
MECI (Multiple Event Count Increment)
IPMI Firmware Revision
Enter the increment value for the multiple event counter. Enter a number between
1 to 255. The default setting is 1.
This item indicates the IPMI firmware revision used in your system.
METW (Multiple Event Count Time Window)
This item indicates the status of the IPMI firmware installed in your system.
This item is used to determine how long (in minutes) should the multiple event
counter wait before generating a new event log. Enter a number between 0 to 99.
The default setting is 60.
System Event Log
IPMI Status
Enabling/Disabling Options
Note: Please reboot the system for the changes to take effect.
View SMBIOS Event Log
This item allows the user to view the event in the SMBIOS event log. Select this
item and press <Enter> to view the status of an event in the log. The following
categories are displayed:
Date/Time/Error Code/Severity
SEL Components
Select Enabled to enable all system event logging support at bootup. The options
are Enabled and Disabled.
Erasing Settings
Erase SEL
Select Yes, On next reset to erase all system event logs upon next system reboot.
Select Yes, On every reset to erase all system event logs upon each system reboot.
Select No to keep all system event logs after each system reboot. The options are
No, Yes, On next reset, and Yes, On every reset.
7-30
7-31
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 7: BIOS
When SEL is Full
Gateway IP Address
This feature allows the user to determine what the BIOS should do when the system event log is full. Select Erase Immediately to erase all events in the log when
the system event log is full. The options are Do Nothing and Erase Immediately.
This item displays the Gateway IP address for this computer. This should be in
decimal and in dotted quad form (i.e., 192.168.10.253).
Note: After making changes on a setting, be sure to reboot the system for
the changes to take effect.
Router MAC Address
This item displays the Router MAC address for this computer.
Log EFI Status Codes
Select EFI (Extensible Firmware Interface) Status Codes to log EFI status codes.
Select Error Codes to log EFI error codes. Select Progress Code to log the EFI
progress code. Select both to log both EFI error codes and progress codes. The
options are Disabled, Both, Error code and Progress code.
Note: After making changes on a setting, be sure to reboot the system for
the changes to take effect.
BMC Network Configuration
The following items will be displayed:
LAN Channel 1
Configuration Address Source
Use this item to select the IP address source for this computer. If Static is selected,
you will need to know the IP address of this computer and enter it to the system
manually in the field. If DHCP is selected, AMI BIOS will search for a DHCP (Dynamic Host Configuration Protocol) server attached to the network and request the
next available IP address for this computer. The options are DHCP Unspecified,
and Static.
Current Configuration Address Source
This item displays the current configuration address source.
Station IP Address
This item displays the Station IP address for this computer. This should be in decimal
and in dotted quad form (i.e., 192.168.10.253).
Subnet Mask
This item displays the sub-network that this computer belongs to. The value of each
three-digit number is separated by dots and it should not exceed 255.
Station MAC Address
This item displays the Station MAC address for this computer. Mac addresses are
6 two-digit hexadecimal numbers.
7-32
7-33
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Chapter 7: BIOS
7-7 Boot Settings
7-6 Security Settings
This menu allows the user to configure the following security settings for the
system.
Use this feature to configure Boot Settings:
Boot Mode Select
Administrator Password
Use this feature to set the administrator password which is required before entering
the BIOS setup utility. The length of the password should be from 3 characters
to 20 characters long.
User Password
Use this feature to set the user password which is required to enter the BIOS
setup utility. The length of the password should be from 3 characters to 20 characters long.
Use this item to select the type of device to be used for system boot. The options
are Legacy, UEFI, and Dual. The default setting is Dual.
Fixed Boot Order Priorities
This option prioritizes the order of bootable devices that the system to boot from.
Press <Enter> on each entry from top to bottom to select devices.
•Dual Boot Order #1
•Dual Boot Order #2
•Dual Boot Order #3
Password Check
Select Setup for the system to prompt for a password at Setup. Select Always for
the system to prompt for a password at bootup and upon entering the BIOS Setup
utility. The options are Setup and Always.
•Dual Boot Order #4
•Dual Boot Order #5
•Dual Boot Order #6
•Dual Boot Order #7
•Dual Boot Order #8
•Dual Boot Order #9
7-34
7-35
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
•Dual Boot Order #10
Chapter 7: BIOS
7-8 Save & Exit
•Dual Boot Order #11
Select the Save & Exit tab from the BIOS setup screen to configure the settings
below.
•Dual Boot Order #12
•Dual Boot Order #13
•Dual Boot Order #14
•Dual Boot Order #15
Add New Boot Option
This feature allows the user to add a new boot option to system boot features.
Add Boot Option
Use this item to specify the name of the driver that the new boot option is
added to.
Path for Boot Option
Discard Changes and Exit
This item is used to specify the path to the driver that the new boot option is
added to. The format for the path is "fsx:\path\filename.efi".
Select this option to quit the BIOS setup without making any permanent changes
to the system configuration, and reboot the computer. Select Discard Changes and
Exit from the Exit menu and press <Enter>.
Boot Option File Path
Save Changes and Reset
Create
Delete Boot Option
When you have completed the system configuration changes, select this option to
leave the BIOS setup utility and reboot the computer for the new system configuration parameters can take effect. Select Save Changes and Exit from the Exit menu
and press <Enter>.
Use this item to select a boot device to delete from the boot priority list.
Save Options
After the driver option name and the file path are set, press <Enter> to enter to
submenu and click OK to create the new boot option drive.
Delete Boot Option
Save Changes
Select the target boot device to delete.
When you have completed the system configuration changes, select this option to
save all changes made. This will not reset (reboot) the system.
Delete Drive Option
Use this item to select a driver to delete from the boot priority list.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to the
AMI BIOS Utility Program.
Delete Driver Option
Select the target driver to delete.
Hard Disk Driver BBS Priorities
This item sets the boot sequence of available hard disk drives.
7-36
7-37
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Restore Defaults
To set this feature, select Restore Defaults from the Exit menu and press <Enter>.
These are manufacture default settings designed for maximum system performance
but not for maximum stability.
Save As User Defaults
To set this feature, select Save as User Defaults from the Exit menu and press <Enter>. This enables the user to save any changes to the BIOS setup for future use.
Restore User Defaults
To set this feature, select Restore User Defaults from the Exit menu and press <Enter>. Use this feature to retrieve user-defined settings that were saved previously.
Boot Override
This feature allows the user to override the Boot priorities sequence in the Boot
menu, and immediately boot the system with another device specified by the user.
This is a one-time override.
7-38
Appendix A: BIOS Error Beep Codes
Appendix A
BIOS Error Beep Codes
During the POST (Power-On Self-Test) routines, which are performed at each
system boot, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue to
boot. The error messages normally appear on the screen.
Fatal errors will not allow the system to continue with bootup procedure. If a fatal
error occurs, you should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps.
The numbers on the fatal error list correspond to the number of beeps for the corresponding error.
Motherboard BIOS Error Beep Codes
Beep Code/LED
Error Message
Description
1 beep
Refresh
Ready to boot
5 short beeps + 1 long beep
Memory error
No memory detected in the
system
5 beeps
No Con-In or No
Con-Out devices
Con-In includes USB or PS/2
keyboard, PCI or Serial Console
Redirection, IPMI KVM or SOL.
Con-Out includes Video Controller, PCI or Serial Console
Redirection, IPMI SOL.
1 beep per device
Refresh
1 beep or each USB device
detected
IPMI Error Codes
1 Continuous Beep
System OH
A-1
System Overheat
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Notes
A-2
Appendix B: System Specifications
Appendix B
System Specifications
Processors
Single or dual Intel® E5-2600 Series (v3/v4) Socket R3 processors in LGA 2011
sockets (both CPUs must be of the same type)
Note: All PCI-E slots will not be enabled when using only a single processor. See the motherboard
layout on page 5-11 for details. Please refer to our web site for a complete listing of supported
processors.
Chipset
Intel C612 chipset
BIOS
16 MB AMI® SPI Flash ROM
Memory Capacity
Sixteen DIMM Slots supporting up to 1 TB of ECC LRDIMM or ECC RDIMM
DDR4-2400/2133/1866/1600 memory
Note: See Section 5-5 for details.
SATA Controller
Intel chipset-based SATA controller for 10 SATA 3.0 ports
Drive Bays
Eight 3.5" hot-swap drive bays to house eight SATA drives
Peripheral Drive Bays
Three 5.25" drive bays
Expansion Slots
Three PCI-E 3.0 x16 and three PCI-E 3.0 x8 expansion slots
B-1
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
Serverboard
Appendix B: System Specifications
Regulatory Compliance
X10DRi/X10DRi-T
Dimensions: 12.1 x 13.05 in (307 x 331 mm)
Electromagnetic Emissions: FCC Class A, EN 55022 Class A, EN 61000-3-2/-33, CISPR 22 Class A
Chassis
SC745TQ-R920B, tower/4U rackmount
Dimensions (as tower): (WxHxD) 7 x 19 x 27 in. (178 x 483 x 686 mm)
Weight
Electromagnetic Immunity: EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3,
EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11)
Safety: CSA/EN/IEC/UL 60950-1 Compliant, UL or CSA Listed (USA and
Canada), CE Marking (Europe)
California Best Management Practices Regulations for Perchlorate Materials:
This Perchlorate warning applies only to products containing CR (Manganese
Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate”
70 lbs. (31.8 kg.)
System Cooling
Three 8-cm system cooling fans
Two 8-cm rear exhaust fans
One air shroud
System Input Requirements
AC Input Voltage: 100 - 240V AC auto-range
Rated Input Current: 13 - 4A max
Rated Input Frequency: 50 to 60 Hz
Power Supply
Rated Output Power: 920W (Part# PWS-920P-1R)
Rated Output Voltages: +12V (75A), +5Vsb (4A)
Operating Environment
Operating Temperature: 10º to 35º C (50º to 95º F)
Non-operating Temperature: -40º to 70º C (-40º to 158º F)
Operating Relative Humidity: 20% to 95% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
B-2
B-3
SUPERSERVER 7048R-TR/7048R-TRT User's Manual
(continued from front)
The products sold by Supermicro are not intended for and will not be used in life support systems,
medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to
result in significant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous
applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend
and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
B-4
Download PDF
Similar pages