Polyeuro MH752 - Data Sheet - with logo

POLYCOAT
PRODUCTS
A Division of American Polymers Corp.
DESCRIPTION
Polyeuro® MH752 is a fast setting, rapid curing, aromatic, two
component, hybrid polyurea/polyurethane spray designed to
be applied over EPS, wood and many other surfaces. Its
excellent balance of stiffness and impact resistance provides
excellent plastic “shell-like” protection for delicate foams and
EPS. Polyeuro® MH752’s chemical design allows fast “userfriendly” application with excellent flow and appearance.
Polyeuro® MH752 offers a tensile strength of 3700 psi upon
curing with 75 Shore D hardness.
FEATURES
Plastic “Shell-Like” Protection Low Shrinkage
100% Solids
Zero VOC
Meets USDA Criteria
Fast Cure
Excellent Thermal Stability
High Productivity
Excellent Chemical Protection
Excellent Cold Temperature Impact Resistance
TYPICAL USES
Decorations / Props
Architectural Shapes
Steel Coating
Food Processing Plants
Speaker Boxes
Dock Flotations
Wood Pallets / Crates
Wood Cabinets
COLORS
Clear/Neutral. Custom colors are available upon request.
Color Packs, when used, must be added to Part-B.
Due to its aromatic composition, Polyeuro® MH752 will tend
to yellow or darken in color and will become flat after exposure
to UV light. Polyeuro® MH752 may be topcoated within twelve
hours of application with an aliphatic polyurethane/polyurea
coating for a colorfast finish.
PACKAGING
10 gallon kit: 5 gallons Part-A (Isocyanate side) and 5 gallons
Part-B (Resin side).
100 gallon kit: 50 gallons Part-A (Isocyanate side) and 50
gallons Part-B (Resin side).
COVERAGE
Polyeuro® MH752 may be applied at any rate to achieve
desired thickness. Theoretical coverage for 1 mil thickness
is one gallon per 1600 sq. ft.
SURFACE PREPARATION
In general, coating performance and adhesion are directly
proportional to surface preparation. Most failures in the
performance of surface coatings can be attributed to poor
surface preparation. Polyurea coatings rely on the structural
strength of the substrate to which they are applied. All surfaces must be free of dust, dirt, oil, grease, rust, corrosion and
other contaminants. When coating substrates previously
POLYEURO® MH752
Two Component Aromatic Hybrid
Polyurethane Protective Coating
Technical Data Sheet
TECHNICAL DATA
Mix Ratio by Volume .......................................... 1A : 1B
Pot Life @ 150°F ................................................ 2-4 seconds
Tack Free Time (150 mils thick) .......................................... 60-120 seconds
Recoat Time ........................................................ 0-12 hours
Viscosity at 150-160°F (66.5-71°C), Brookfield:
Part-A ................................................................. 90 ± 20 cps
Part-B ................................................................. 160 ± 20 cps
Density (Side A & B Combined) ........................ 9.03 lbs/gal
Flash Point .......................................................... >200°F
Hardness, ASTM D-2240 .................................. 75 ± 5 D
Tensile Strength, ASTM D-412* ........................ 3700 ± 200 psi
Elongation, ASTM D-412* .................................. 40% ± 20%
Tear, Die “C” ASTM D-624* ............................... 450 ± 50 pli
Service Temperature ......................................... -20°F to 250°F
(*These physical properties from sample sprayed with Graco Foam
Cat 200 @ 2000 psi minimum, with Gusmer GX7-400 mechanical
purge gun @ 150-160°F. Different machine and parameter will
change these properties. User should perform their own independent
testing as properties are approximate.)
used, it is important to consider the possibility of substrate
absorption, which may affect the adhesion of the coating
system, regardless of the surface preparation. Polycoat
recognizes the potential for unique substrates from one
project to another. The following information is for general
reference, and for project-specific questions, contact Polycoat.
New and Old Concrete:
Refer to SSPC-SP13/NACE 6, or ICRI 03732: CSP 3-5. New
concrete must be cured for 28 days prior to product application. Surface must be clean, dry, sound and offer sufficient
profile for product adhesion. Remove all dust, dirt, oil, form
release agents, curing compounds, salts, efflorescence,
laitance and other foreign matter by shotblasting and/or
suitable chemical means, in accordance with local chemical
regulations. Rinse thoroughly, to achieve a pH between 8.0
and 11.0. Allow to dry completely. If old concrete has a surface
that has deteriorated to an unacceptably rough surface,
Polycoat Products PC-260 or a mixture of Polyprime 21 and
sand should be used as a repair agent for cracks, spalls, bug
holes and voids. Upon full cure of the repair agent, prime the
entire surface intended for coating.
Concrete Surface Preparation Reference:
ASTM D4258 - Standard practice for cleaning concrete
ASTM D4259 - Standard practice for abrading concrete
ASTM D4260 - Standard practice for etching concrete
ASTM F1869 - Standard test method for measuring moisture
vapor emission rate of concrete
ICRI 03732 Concrete surface preparation
Wood:
All wood should be clean, dry and free of any knots, splinters,
oil, grease or other contaminants. Splintered or rough areas
14722 Spring Avenue  Santa Fe Springs, CA 90670-5108 USA  Tel: 562/802-8834  Fax: 562/921-7363  www.polycoatusa.com  Copyright  September 2011 Polycoat Products
should be sanded. Knots should be repaired using Polycoat
Products PC-260 with sand. Upon full cure of the repair agent,
prime the entire surface intended for coating.
Steel (Atmospheric and Immersion Exposure):
Remove all oil, grease, weld spatters and round off any sharp
edges from surface. Minimum surface preparation is Near
White Metal Blast Cleaning per SSPC-SP10/NACE 2. Optimum surface profile is 2-3 mils. Prime and shoot Polyeuro®
on to any bare metal the same day as it is cleaned to minimize
any potential flash rusting.
Aluminum:
Aluminum should be blasted with aluminum oxide or sand,
and not with steel or metal grit. Excessive blasting may result
in a warped or deformed surface. After blasting, wash aluminum with a commercially available aluminum cleaner. Allow
to dry, then prime.
Brass and Copper:
Brass and copper should be blasted with sand, and not with
steel or metal grit. Remove all dust and grease prior to
applying primer.
Galvanized Surfaces:
Clean and degrease any contaminated surfaces before
priming. Do not blast galvanized surfaces with an abrasive
grit. An adhesion test is recommended prior to starting the
project.
Fiberglass Reinforced Plastic:
The gel coat should be lightly blasted or sanded with 80 grit
sandpaper and cleaned.
Plastic Foams:
Enhanced adhesion is obtained when the foam is mechanically abraded. When coating polystyrene, do not use a
solvent-based primer.
Textiles, Canvas, Fabrics:
Adhesion to most fabrics, geothermal membranes and textiles does not require a primer.
Stainless Steel:
Stainless steel may be grit blasted and degreased before
priming. Some stainless steel alloys are so inert that it is not
possible to achieve a satisfactory bond. An adhesion test is
recommended prior to starting the project.
New and Old Cast Iron:
Blast with a steel grit and degrease before priming. Old cast
iron is difficult to prepare for a satisfactory bond. It can absorb
oil and water soluble contaminants that will keep returning to
the surface after the coating system has been applied and
affect the coating system adhesion. An adhesion test is
recommended prior to starting the project.
All Other Surfaces:
An adhesion test is recommended prior to starting the project.
MIXING
Polyeuro® MH752 may not be diluted under any circumstances. Thoroughly mix Polyeuro® MH752 Part-B material
with air driven power equipment until a homogeneous mixture and color is obtained.
APPLICATION
Both Part-A and Part-B material should be preconditioned at
80-90°F before application.
Recommended surface temperature must be at least 5°F
above the dew point.
Polyeuro® MH752 should be applied using a plural component, heated, high pressure 1:1 spray mixing equipment like
Graco’s Reactor, Glass Craft or other equivalent machine
may be used.
Both Part-A and Part-B materials should be sprayed at a
minimum of 2000 psi and at temperatures above 150°F.
Adequate pressure and temperature should be maintained
at all times.
Polyeuro® MH752 should be sprayed in smooth, multidirectional passes to improve uniform thickness and appearance.
STORAGE
Polyeuro® MH752 has a shelf life of six (6) months from
date of manufacture in original, factory-sealed containers.
Part-A and Part-B drums are recommended to be stored
above 60°F.
Avoid freezing temperatures.
Store drums on wooden pallets to avoid direct contact with the
ground.
If stored for a long period of time, rotate Part-A and Part-B
drums regularly.
LIMITATIONS
Do not open until ready to use.
Both Part-A and Part-B containers must be fitted with a
desiccant device during use.
WARNING
This product contains Isocyanates and Curative Material.
Please read all information in the general guidelines, product data sheets, guide specifications and material safety data sheets (MSDS) before applying material. Published technical data and instructions are subject to change without notice. Contact your local Polycoat
Products representative or visit our website for current technical data and instructions.
LIMITED WARRANTY
Polycoat Products warrants its products to be free of manufacturing defects and that they will meet Polycoat Products current published physical properties. Polycoat Products warrants that its products, when properly installed by a state licensed waterproofing contractor according to
Polycoat Products guide specifications and product data sheets over a sound, properly prepared substrate, will not allow water migration for a period of one (1) year. Seller’s and manufacturer’s sole responsibility shall be to replace that portion of the product of this manufacturer
which proves to be defective. There are no other warranties by Polycoat Products of any nature whatsoever expressed or implied, including any warranty of merchantability or fitness for a particular purpose in connection with this product. Polycoat Products shall not be liable for
damages of any sort, including remote or consequential damages resulting from any claimed breach of any warranty whether expressed or implied. Polycoat Products shall not be responsible for use of this product in a manner to infringe on any patent held by others. In addition, no
warranty or guarantee is being issued with respect to appearance, color, fading, chalking, staining, shrinkage, peeling, normal wear and tear or improper application by the applicator. Damage caused by abuse, neglect and lack of proper maintenance, acts of nature and/or physical
movement of the substrate or structural defects are also excluded from the limited warranty. Polycoat Products reserves the right to conduct performance tests on any material claimed to be defective prior to any repairs by owner, general contractor, or applicator.
DISCLAIMER
All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or
implied. It is the users responsibility to satisfy himself, by his own information and test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest or guarantee
that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements,
whether in writing or oral, other than those contained herein shall not be binding upon the manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the
material and proper application procedures. Test performance results were obtained in a controlled environment and Polycoat Products makes no claim that these tests or any other tests, accurately represent all environments.
14722 Spring Avenue  Santa Fe Springs, CA 90670-5108 USA  Tel: 562/802-8834  Fax: 562/921-7363  www.polycoatusa.com  Copyright  September 2011 Polycoat Products
Download PDF
Similar pages