FFR 2x2, 2x4, 1x4 Installation Instructions

LUMEN FOCUS FFR KIT INSTALL INSTRUCTIONS
CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PREFORMED BY A QUALIFIED ELECTRICIAN OR SERVICE PERSONNEL
WARNING - RISK OF FIRE OR ELECTRIC SHOCK.
INSTALL THIS KIT ONLY IN LUMINAIRES THAT HAVE
THE CONSTRUCTION FEATURES AND / OR DRAWINGS
AND WHERE THE IMPUT RATING OF THE REROFIT KIT
DOES NOT EXCEED THE INPUT RATING OF THE LUMINAIRE.
WARNING - TO PREVENT WIRING DAMAGE OR ABRASION,
DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR
OTHER SHARP OBJECTS.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK, LUMINAIRE
WIRING AND ELECTRICAL PARTS MAY BE DAMAGED WHEN
DRILLING FOR INSTALLATION OF LED RETROFIT KIT.
CHECK FOR ENCLOSED WIRING AND COMPONENTS.
REMOVAL PROCESS
1. TURN OFF POWER
2. REMOVE LENS / DOORFRAME FROM FIXTURE
3. REMOVE LAMPS(RECYCLE AS NEEDED)
4. REMOVE FLUORESCENT REFLECTOR, BALLAST,
SOCKETBARS AND EXCESS WIRING FROM
FIXTURE
CAUTION: UNLESS OTHERWISE INDICATED, DO NOT
MAKE OR ALTER ANY OPENINGS IN THE COMPARTMENT
OF WIRING OR ELECTRICAL DURING INSTALLATION OF THIS
RETROFIT ASSEMBLY. PLUG ALL UNUSED OPENINGS IN THE
COMPARTMENT OF WIRING OR ELECTRICAL COMPONENTS.
"DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE
OF WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.
WARNING - RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL
INJURY. BEFORE INSTALLATION TURN POWER OFF.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK, LED RETROFIT
KIT INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES
ELECTRICAL SYSTEMS. IF NOT QUALIFIED DO NOT ATTEMPT
INSTALLATION. CONTACT A QULIFIED ELECTRICIAN.
2X4 KIT SHOWN
FIXTURE IN CEILING GRID
PAGE 1 OF 3
LUMEN FOCUS FFR KIT INSTALL INSTRUCTIONS
CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PREFORMED BY A QUALIFIED ELECTRICIAN OR SERVICE PERSONNEL
WARNING - RISK OF FIRE OR ELECTRIC SHOCK.
INSTALL THIS KIT ONLY IN LUMINAIRES THAT HAVE
THE CONSTRUCTION FEATURES AND / OR DRAWINGS
AND WHERE THE IMPUT RATING OF THE REROFIT KIT
DOES NOT EXCEED THE INPUT RATING OF THE LUMINAIRE.
WARNING - TO PREVENT WIRING DAMAGE OR ABRASION,
DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR
OTHER SHARP OBJECTS.
WARNING - RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL
INJURY. BEFORE INSTALLATION TURN POWER OFF.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK, LUMINAIRE
WIRING AND ELECTRICAL PARTS MAY BE DAMAGED WHEN
DRILLING FOR INSTALLATION OF LED RETROFIT KIT.
CHECK FOR ENCLOSED WIRING AND COMPONENTS.
SQUARE CUT OUT ON
LED PANEL
KIT INCLUDES
CAUTION: UNLESS OTHERWISE INDICATED, DO NOT
MAKE OR ALTER ANY OPENINGS IN THE COMPARTMENT
OF WIRING OR ELECTRICAL DURING INSTALLATION OF THIS
RETROFIT ASSEMBLY. PLUG ALL UNUSED OPENINGS IN THE
COMPARTMENT OF WIRING OR ELECTRICAL COMPONENTS.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK, LED RETROFIT
KIT INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES
ELECTRICAL SYSTEMS. IF NOT QUALIFIED DO NOT ATTEMPT
INSTALLATION. CONTACT A QULIFIED ELECTRICIAN.
DETAIL A
SEE PAGE #3
SEE PAGE #3
QTY.
1
1
1
1
2
2
2
2
1
1
PART NUMBER.
FFR ENDCAP LEFT HAND
FFR ENDCAP RIGHT HAND
FFR LED PANEL
FFR BLANK PANEL
QUARTER TURNS
SAFETY STRAPS
SELF-TAPPING SCREWS
TEK-SCREWS
LENS
873-902 DISCONNECT
ITEM
A1
A2
B
C
D
E
F
G
H
I
ITEM D
ROUND HOLE IN LED PANEL
DIMPLE ON FORM TAB
SLIDE LED PANEL
FORM TAB ON
FFREC LH & RH
INSTALL FFREC'S BY
SLIDE IN BETWEEN
TROFFER AND GRID
A1
ITEM B
A2
1. PLACE FFR ENDCAP AT EACH END OF THE
2. SLIDE LED PANEL BETWEEN GRID AND TROFFER FASTEN USING SQ CUT OUT
ON LED PANNEL AND FORM TAB ON ENDCAP SEE DETAIL A
3. CONNECT LED PANEL ELECTRICAL WITH PROVIDED DISCONNECT
WHITE(NEUTRAL) TO WHITE, BLACK(POWER FEED) TO BLACK
CONNECT GREEN GROUND TO FIXTURE BACK WITH PROVIDED SCREW
4. INSTALL SAFETY-STRAP AT EACH END OF FIXTURE
1 SELF-TAPPING SCREW USED TO ATTACH STRAP TO ENDCAP
CONNECT OTHER END OF SAFETY-STRAP TO FIXTURE USING TEK-SCREW
ALL SCREWS ARE PROVIDED IN KIT.
5. SLIDE BLANK PANEL BETWEEN GRID AND TROFFER
FASTEN WITH PROVIDED QUARTER TURNS ITEM D 2X
ITEM C
VIEW OF KIT WITH SAFETY CABLES INSTALLED
SEE DETAL A 2X
FFREC,S INSTALLED
ITEM D
A1
A2
ITEM E
ITEM E
USE SELF-TAPPING SCREW
TO INSTALL TO END CAP
PROVIDED IN KIT ITEM F 2X
INSTALL LUMINAIRE
MODIFICATION LABEL
PROVIDED IN KIT
USE TEK-SCREW
TO INSTALL IN
THE FIXTURE
PROVIDED IN KIT ITEM G 2X
PAGE 2 OF 3
LUMEN FOCUS FFR KIT INSTALL INSTRUCTIONS
CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PREFORMED BY A QUALIFIED ELECTRICIAN OR SERVICE PERSONNEL
WARNING - RISK OF FIRE OR ELECTRIC SHOCK.
INSTALL THIS KIT ONLY IN LUMINAIRES THAT HAVE
THE CONSTRUCTION FEATURES AND / OR DRAWINGS
AND WHERE THE IMPUT RATING OF THE REROFIT KIT
DOES NOT EXCEED THE INPUT RATING OF THE LUMINAIRE.
WARNING - TO PREVENT WIRING DAMAGE OR ABRASION,
DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR
OTHER SHARP OBJECTS.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK, LUMINAIRE
WIRING AND ELECTRICAL PARTS MAY BE DAMAGED WHEN
DRILLING FOR INSTALLATION OF LED RETROFIT KIT.
CHECK FOR ENCLOSED WIRING AND COMPONENTS.
CAUTION: UNLESS OTHERWISE INDICATED, DO NOT
MAKE OR ALTER ANY OPENINGS IN THE COMPARTMENT
OF WIRING OR ELECTRICAL DURING INSTALLATION OF THIS
RETROFIT ASSEMBLY. PLUG ALL UNUSED OPENINGS IN THE
COMPARTMENT OF WIRING OR ELECTRICAL COMPONENTS.
WARNING - RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL
INJURY. BEFORE INSTALLATION TURN POWER OFF.
WARNING - RISK OF FIRE OR ELECTRIC SHOCK, LED RETROFIT
KIT INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES
ELECTRICAL SYSTEMS. IF NOT QUALIFIED DO NOT ATTEMPT
INSTALLATION. CONTACT A QULIFIED ELECTRICIAN.
WIRE SCHEMATIC
Line side input to driver
120V to 277V and all voltages in between
120V - 277V input
BLACK
WHITE
LINE
SNAP LENS IN
INSTALL LENS ON TO KIT.
1. TO INSTALL LENS SNAP INTO TRACK. ITEM H
2. TURN POWER BACK ON
ITEM H
DRIVER
ITEM I
PAGE 3 OF 3
Download PDF
Similar pages