Malibu Boats iRide XTi Specifications

2013
Product Catalog
We make booms to fit any type of boat and on the
tubing of any wakeboard tower. Call us to find out
which boom you need for your boat.
Designed • Manufactured
Crafted • Assembled
In the good old US of A
You can wakesurf on any boat by adding Fatsacs where needed.
Call us to find out what Fatsacs you need to wakesurf on your boat.
Barefoot International & Fly High Mfg. offers consumers a line of superior products developed through careful research and testing. As the rest of our competitors have been busy finding overseas
suppliers to fulfill their needs, we have been steadily upgrading our capabilities in-house. Our booms, pylons, towers, Fat Sacs™ and other products are specifically designed to provide added
safety, convenience and improved performance without causing damage to your boat. We don’t compromise safety nor ease of use for gimmick features. Barefoot International & Fly High Mfg. is
your assurance of the highest quality equipment available today.
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com E: orders@fatsac.com • 3879 N. Richards Street • Milwaukee, WI 53212
FLY HIGH | TOWERS
Pro X Series Tower Extension
#W2927 / #W2931 / #W2932
One of Barefoot International’s Awesome Inventions
The Super Fly High Tower Extension (Patented)
We make Super Fly High Tower Extensions
to fit any wakeboard tower. Call us for the
part # for the one that fits your tower.
Patented
The new Pro X Series Tower Extension is the most extreme new product to hit the market.
It fits all towers and allows you to go bigger and land softer. It also helps you learn new
tricks at slower speeds which will increase your confidence while reducing the punishment of
crashing. Trying to land that first raley? Slow the boat to 18 mph and give it a rip. It quickly
folds down entirely and can remain attached while your tower is collapsed, so there is no
need to remove it prior to parking your boat on the lift.
W2927 - 2” or less tower diameter
W2931 - 2¼” - 2½” tower diameter
W2932 - 2 ⅞” and 3” tower diameter
FLY HIGH | TOWERS
Pro X Series Tower
• Only universal wakeboard tower built strong enough to pull tubes
• Only stainless steel adjustable wakeboard tower
#W2923
The Pro X Series Tower is completely universal and the only one
constructed of stainless steel making it the strongest and most durable tower on the market. The Quick Release pins are user friendly
and make stowing and setup of the tower a simple task. Just pull
six pins and the tower folds down entirely allowing an easier fit into
your garage and lift. This tower offers exclusive overhead crossbar
engineering which locks it in and makes it as rigid as a factory installed tower. The crossbars of the tower act as an integrated board
rack that will store anything from a slalom ski to a wake surf board.
Classic swoop style looks great on any boat. Board pads included.
• Classic swoop style looks great on any boat
• Board pads on overhead crossbars double
as a board rack and provide shade when
loaded with skis & boards
• Folds down as low as the windshield
• Adjusts to fit any boat
Pro X Series Deck Boat Crossbar Tower
#W2934
The Pro X Series Deck Boat Crossbar Tower (W2934) is the same
as our Pro X Series Crossbar Tower (W2923) a far as looks and
everything. The only difference is that the Pro X Series Deck Boat
Crossbar Tower (W2934) is made to fit deck boats. The front of Deck
boats stay wide.
Board Pads
Pro X Series Crossbar Tower is the only tower that you can add to
your boat that is strong enough to pull multiple tubes...Or anything
else, and it will never vibrate loose or crack your boat’s fiberglass
when you do 3 key things:
1. Making sure that our supplied underplates are mounted flush.
2. Fully tighten the rear overhead adjustable crossbar with 3 guys using
their bare hands after the tower has been installed!
3. Double check that every nut bolt and screw is fully tightened.
#W2925
You can customize the look of your tower with these color board
pads.
You can use the crossbars of the tower
to quickly store all of your equipment.
The Pro X Series Tower is the only tower
on the market designed with this in
mind. The crossbars can accommodate
anything from a single slalom ski to a
wake surf board.
FLY HIGH | TOWERS & ACCESSORIES
Pro X Series Rolled Cage
Pro X Series Board Rack
#W2922
#W2906 / W2907
The Pro X Series Cage is a simple yet effective design. It’s made of high quality 2” and 2 ½” stainless
steel and adjusts to fit any boat. Mount the arms to the front or back of the boat to give it a distinct
look. It’s fully collapsible as well.
The Pro X Series Board Rack is designed to fit any tower and comes with arm extensions to
accommodate wake surf boards. (W2906 - 2” or less O.D. towers / W2907 - 2 ¼” - 2½” O.D.
towers.
Rope Guide
#W912
The Rope Guide can be used with all Fly High towers and the stainless steel Fly High X-Pole. It quickly attaches to the delron swivel and helps keep the rope off your racks and out of the boat.
FLY HIGH | PYLONS
Stainless Steel Fly High X-Pole
Aluminium Fly High X-Pole
#W2900
#W913x
The stainless steel Fly High X-Pole is still the only high quality stainless steel extended pylon on
the market and it is made to fit 2 ½” pylons. It’s the only extended pylon with a delron swivel at
the top and at pylon height. It’s superior strength and safety comes from our dual stainless steel
cable system. It has a poly carbonate sleeve inside to protect your factory pylon.
The Aluminium Fly High X-Pole is anodized black and made to fit 2 ½” pylons. This monster is similar to the stainless steel Fly High X-Pole but is one piece instead of two. It also
has a poly carbonate sleeve inside to protect your factory pylon and our dual stainless
steel cable system.
Pro Ski Pylon
Bass Boat Pylon
#W411 / W412
#W404
The Pro Ski Pylon comes in two forms, fixed and adjustable. The fixed version of the pylon is 45” tall while the
adjustable version can be set to a height from 34”-58”.
(W411 - adjustable height / W412 - fixed height)
The Bass Boat Pylon is designed to utilize the seat mount of your bass boat. It can be
quickly installed and removed and has two telescoping support arms that provide stability.
FLY HIGH | PYLONS & ACCESSORIES
Pro Deck Master Pylon
Cable Protector
#W400
#B108
The Pro Deck Master Pylon was designed to be fitted to the engine
well of a boat where the surface may not be horizontal. It’s design is
simple yet effective.
Replacement cable protector for your Fly High pylons.
Delron Height Adjuster
Delron Pro Ski Swivel
#W2902 / W2902-3
#W401
Fits extended pylons allowing you to adjust the height of the attachment point for the rope. (W2902 for 2 ½” pylons / W2902-3 for 3”
pylons)
Pylon Case
Ski Tow Hitch
#W501
#W403
Our Pylon case is the best way to transport and store your stainless steel Fly High X-Pole. You won’t have to worry
about the latch on the cable smacking your ankles when carrying the pylon with this thing.
The Delron Swivel is a compact design and can be permanently
mounted to any boat or jet ski. Just remove the ski tow ring and
replace it with this high tech delron swivel.
This pylon can be mounted to the transom of I/O Boats.
FLY HIGH | FAT SACS
You can wakesurf on any boat by adding
Fatsacs where needed. Call us to find out
what Fatsacs you need to wakesurf on
your boat.
You can get your custom fat sacs taylor
made to your exact specifications!
To make your wake, call 414-964-3668.
x.
Valme
d
e
l
l
l ca
ome
ateria hey also c s
m
g
ing
ftin
l. T
ter ra outer shel g these th to
a
w
e
hit
an
inin
ible
th a w support of g and dra es it poss aili
w
d
t he
uc t e
mak cs are av r
fillin
onstr nger need making ur valves
c
e
r
a
All sa ok of you
o
o
m
l
.
e
f
t
o
™
m
o
s
s
n
e
o
y
t
c
t
at Sa urable and ct Valve s placemen allast sys mize the l
F
s
e
i
er
ne
s to
he
yd
db
ro X S nbelievabl Quick Con ermore, t integrate olors to cu
P
w
e
h
t
The n sacs are u with our task. Furt he perfec assorted c .
d
m
n
sy
et
These equippe
syste
able i
creat
an ea
FLY HIGH | FAT SACS
You can wakesurf on any boat by adding Fatsacs where needed. Call us to find out what Fatsacs you need to wakesurf on your boat.
Pro X Series Fat Sac™
Custom Fat Sacs - W507-C
#W707 - 50x20x20 - 750 lbs. (Expand to about 950lbs.)
ANY SHAPE...ANY SIZE...ANY VALVE CONFIGURATION
#W707-EXV - 50x20x20 - 750 lbs. (Expand to about 950lbs.)
Get your custom fat sacs taylor made to your exact specifications!!
To make your wake call 1-414-964-3668
You can special order sacs to suit your needs. We make all of our Fat Sacs in house which
gives us the ability to create custom sacs for our customers. The same process that is
used to build our Pro X Series line of Fat Sacs will be utilized to create your custom sacs.
By using our advanced cutting machine, welding system and Valmex material we can
assure you that your designed sac will be extremely durable and of the highest quality.
You also decide on which type of Quick Connect fittings you would like to use, how many
there are and their exact location on the sac. Whether it’s a totally customized integrated
system you are looking for, or just a single sac, let your creative juices flow because you’re
in control.
The original Fat Sac™ redefined and setting new standards. These sacs are the most demanded on the market for their durability and ease of use. Two of these slobs will add 1500
lbs. of ballast when fully loaded.
Note: The W707-EXV comes with a 4th valve on the bottom of the other end; in grey only.
Pro X Series V-Drive Sacs (set)
#W701 - 42x16x16 - 400 lbs. each (Expand to about 550lbs.)
The Pro X Series V-Drive Sacs were designed to fit perfectly in the rear compartments in
v-drive boats. Combined with the weight of the engine, these sacs will produce a monster
wake.
Pro X Series Fat Brick
#W702 - 16x16x16 - 155 lbs. (Expand to about 185lbs.)
#W702
This little thing weighs in at 155 pounds. Its handles and compact size allow you to quickly
reposition it to fine-tune your boat’s wake and eliminate any unwanted wash.
#W707
#W707-EXV
Pro X Series Fat Seat
#W710 - 1525 lbs. Patented (Expand to about 1800lbs.)
#W710
The Pro X Series Fat Seat is design for inboard boats that have a removable rear seat. This
thing is huge with arms that extend forward on either side of the engine compartment to
add even more weight.
#W701
Pro X Series Nautique Wedge Sacs (set)
#W708 - 42x16x18 - 400 lbs. each (Expand to about 400lbs.)
The Pro X Series Nautique Wedge sacs are shaped to fit the rear compartments of Mid-2000
year Nautique V-Drive boats, but can be used in any boat.
#W708
available colors
FLY HIGH | FAT SACS
You can wakesurf on any boat by adding Fatsacs where needed. Call us to find out what Fatsacs you need to wakesurf on your boat.
Pro X Series Integrated Bow Sac
#W711
#W711 - 725 lbs. (Expand to about 1000lbs.)
The Pro X Series Integrated Bow Sac is designed to fit under the seats of open bow boats
adding needed weight to the front of the boat.
#W704
Pro X Series Tube Sac
#W704 - 62x16x10 - 370 lbs. (Expand to about 550lbs.)
The Pro X Series Tube Sac can be used in the ski locker of your boat or on the floor just
forward of the engine compartment. It’s longer and narrow enough to fit perfectly along the
walkway to the bow or in many other places.
Pro X Series Side Sacs (set)
#W703 - 48x12x12 - 260 lbs. each (Expand to about 350lbs.)
#W703
The Pro X Series Side Sacs fit along the side of the engine compartment on inboard boats
and they will conform to fit under the seats of open bow boats. They are designed to get
more weight forward in the boat to balance any ballast you may have back by the engine.
Pro X Series Open Bow Sac
#W706
#W706 - 1000 lbs. (Expand to about 1500lbs.)
The Pro X Series Open Bow Sac is triangular in shape and fits open bow boats.
Pro X Series Rear Seat Bottom/Center Locker Sac
#W705 - 60x26x10 - 650 lbs. (Expand to about 1000lbs.)
The Pro X Series Rear Seat Sac is a smaller version of the Fat Seat minus the arms. It has a
lower profile but adds a lot of weight to the rear of the boat. It will also conform to fit in any
center locker and many other places.
Custom Sacs
#W705
#W507-C
available colors
You can special order sacs to suit your needs. All of our Fat Sacs are made in house giving
us the ability to create custom sacs for you. We use the same process as we do in our Pro X
Series line to make custom sacs. Our advanced cutting machine, welding system and Valmex
material will assure you that your designed sac will be extremely durable and of the highest
quality. You also decide on which type of Quick Connect fittings you would like to use, how
many there are and their exact location on your custom sac.
FLY HIGH | FAT SACS & ACCESSORIES
You can wakesurf on any boat by adding Fatsacs where needed. Call us to find out what Fatsacs you need to wakesurf on your boat.
available colors
Pro X Series Ultimate Wake Surf Sac
#W718 - 60x24x16 arms 35x12x16 - 1150 lbs.
After filling any factory ballast and FatSac that fill the front and rear compartments of your
V-drive boat, put the Ultimate Wake Surf Sac on top of the rear seat and side seat that you are
wake surfing on for the ultimate surf wake. This will displace so much water that people will
no longer have to learn to wake surf behind your boat they will just be able to do it. Be sure
to remember to give the boat some throttle to bring the front of your boat up enough when
passing thru any wakes you are making so you don’t swamp the boat. Will also conform to fit in
other type boats and in other places. (Expands to about 1450lbs.)
#W713
#W718
It is important to hold the Ultimate Wakesurf
Sac (W718) when you are filling and emptying
it but when it is full it is firm so it cannot roll
off the seats because it is shaped like a ‘L’.
Pro X Series V-Drive Wake Surf Sac
#W713 - 42x16x16 - 400lbs.
The Pro X Series V-Drive Wake Surf Sac fits perfectly in the compartment of your v-drive
boat to produce a nice wake for surfing behind your v-drive boat. (Expands to about 550lbs.)
Pro X Series Jumbo V-Drive Wake Surf Sac
#W719 - 50x24x24 - 1100 lbs.
#W719-EXV - 50x24x24 - 1100 lbs.
Will conform to fit and fill any rear V-Drive compartment to give you maximum weight. Also will conform to fit in other places and in other type boats.
(Expands to about 1350lbs.)
Note: The W719-EXV comes with a 4th valve on the bottom of the other end; in
grey only.
Tsunami Pump
#W709
The Tsunami Pump System has a larger diameter hose
which doesn’t choke the pump, resulting in greater output.
#W719
#W719-EXV
Jabsco Ballast Pump
#W610-P
High volume, self-priming, reversible, metal ballast
pump. Best for automatic ballast systems.
Socket Splitter
#W405
The socket splitter is exactly what you would expect. Use this thing
to get two Tsunami Pumps flowing and fill those sacs double-time.
FLY HIGH | SEMI-CUSTOM SACS
You can wakesurf on any boat by adding Fatsacs where needed. Call us to find out what Fatsacs you need to wakesurf on your boat.
Enzo Fat Sac™
#W712
#W712 30x25x26 arm 72x25x12 - 1450 lbs.
The Enzo Sac is enormous. It’s designed for v-drive boats that have an opening in the rear
seat bulkhead which leads forward under the side passenger benches. The large part of the
sac fills the rear storage compartments while the lower profile extension runs forward below
the seats. FITTINGS SOLD SEPARATELY
MasterCraft X-2 Rear Fat Sac™
#W714
#W714 - 32x18x20 - 455 lbs. (Expand to about 600lbs.)
The X-2 Rear Fat Sac™ was designed to fit perfectly in the shorter rear compartments of
this boat. It may be a bit shorter that the traditional Pro X Series Fat Sac™ but it still adds
some serious weight to the boat. FITTINGS SOLD SEPARATELY
MasterCraft X-2 Integrated Bow Fat Sac™
#W717 - 690 lbs. (not pictured) (Expand to about 900lbs.)
#W841
The X-2 Integrated Bow Fat Sac™ was designed to fit perfectly under the open bow seats of
a X2. FITTINGS SOLD SEPARATELY
Mastercraft X-2 Fat Sac™ Additional Ballast System
#558032 - 1600 lbs. (not pictured)
2 Custom Rear X-2 Sac • 1 Custom X-2 Integrated Bow Sac (under seats) • 3 Custom Distribution Flow Valves • 50’ of 1” reinforced black bilge hose • 3 Check Valve T-assemblies •
30 hose clamps • all custom fittings
Rear Gravity Games Fat Sac™
#W841 - 42x19x19 - 565 lbs. (Expand to about 750lbs.)
#W842
The Rear Gravity Games Fat Sac™ is built to fit in the compartment of v-drive boats. Two
of these sacs combined with the Center Gravity Games Fat Sac™ provide over 2,300 lbs.
additional ballast to your boat. It’s easy to see why this is the combination used in all the
Gravity Games boats. FITTINGS SOLD SEPARATELY
Center Gravity Games Fat Sac™
#W842 - 88x19x19 - 1180 lbs. (Expand to about 1500lbs.)
X-Star Fat Sac™ Additional Ballast System
#W715 / #558031 - 2500 lbs. (not pictured)
W715 - Includes 2 Custom Rear V-Drive Compartment Sacs • 2 Custom Front Open Bow Sacs (Fittings sold separately)
558031 - Includes 2 Custom Rear V-Drive Compartment Sacs • 2 Custom Front Open Bow Sacs • 3 Custom Distribution
Flow Valves • 50’ of 1” reinforced black bilge hose • 3 Check Valve T-assemblies • 30 hose clamps • all custom fittings
558031 Control System - Jabsco Electronic pump timer (SOLD SEPARATELY; only needed for 2007 Mastercrafts)
The Center Gravity Games Sac is only one inch smaller in width and height of a Fat Sac™, but at over
3 feet longer it weighs in at nearly twice the weight of a single Fat Sac™. Try combining this sac with
two Rear Gravity Games Fat Sacs™ for one monster of a wake. FITTINGS SOLD SEPARATELY
X-Star Bow Walkthrough Fat Sac™
W752 - 39x13x20 - (not pictured)
This fat sac™ is combined with our additional ballast system for the complete package used
on the Pro Wakeboarding Tour. FITTINGS SOLD SEPARATELY
FLY HIGH | SEMI-CUSTOM SACS
You can wakesurf on any boat by adding Fatsacs where needed. Call us to find out what Fatsacs you need to wakesurf on your boat.
Super Air Nautique Center Locker Fat Sac™
#W031
#W721 - arrow 38x38x24 arm 10x11x21 - 650 lbs.
Designed to fit and maximize the weight in the arror shaped center locker of the
Super Air Nautique. FITTINGS SOLD SEPARATELY
Super Air Nautique Additional Ballast System
#W721
#W760 - 1600 lbs. (not pictured)
Includes 2 Pro X Series V-Drive Sacs • 1 Pro X Series Integrated Drive Sac • 1 Tsunami Pump
• 1 Pro X Series Fat Brick • all custom fittings
Malibu Plug & Play Wedge Rear Fat Sac™
#W034-1 1/8 (not pictured)
#W034-1 1/8 - 37.5x19.5x19 - (1 1/8” Fittings Included) - 550lbs.
Axis Wake Plug & Play Fat Sac™
W030 / W031 / W031-1 1/8 / W032 / W036-1 1/8 / W037-1 1/8 / W038-1 1/8
Everything comes done for you with these custom sacs and the Axis Wake Research. The fittings are already
screwed into the sac with pvc cement.
W030
- Axis Wake Plug & Play Rear Sac - 42x16x16 - (3/4” Fittings Included) - 400lbs.
W031
- Axis Wake Plug & Play Bow Sac - arrow 48x40x8 arm 32x15x8 (3/4” Fittings Included) - 950lbs.
W031-1 1/8 - Axis Wake Plug & Play Bow Sac - arrow 48x40x8 arm 32x15x8 (1 1/8” Fittings Included) - 950lbs.
W032
- Axis Wake Plug & Play Rear Sac - 50x20x20 - (3/4” Fittings Included) - 750lbs.
W036-1 1/8 - Axis Wake Plug & Play Rear Sac - 50x24x24 - (1 1/8” Fittings Included) - 1100 lbs. (not pictured)
W037-1 1/8 - Axis Wake Plug & Play Rear Sac - 50x20x20 - (1 1/8” Fittings Included) - 750 lbs. (not pictured)
W038-1 1/8 - Axis Wake Plug & Play Rear Sac - 42x16x16 - (1 1/8” Fittings Included) - 400 lbs. (not pictured)
#W030 / #W032
Mastercraft Plug & Play X-Star Ballast Sac™
#W040/#W041/#W042/#W043/#W044/#W045/#W048/#W049/#W140/#W141
Tige Custom Surf Fat Sacs™
#W004-STB / #W004-P / #W005-STB / #W005-P (not pictured)
These Semi-Custom Fat Sacs are made to the Tige Engineer’s specifications. FITTINGS SOLD SEPARATELY.
W004-STB - Tige 59” Custom Starboard Surf Sac - body 31x24x20 arm 28x24x9 - 800 lbs.
W004-P - Tige 59” Custom Portside Surf Sac - body 31x24x20 arm 28x24x9 - 800 lbs.
W005-STB - Tige 84” Custom Starboard Surf Sac - body 31x24x20 arm 53x24x9 - 1000 lbs.
W005-P - Tige 84” Custom Portside Surf Sac - body 31x24x20 arm 53x24x9 - 1000 lbs.
Supra SA Plug & Play Rear Fat Sac™
W892-1 1/8 - 750 lbs. - (not pictured)
Fittings included.
The Mastercraft engineers got together with us to make these different models of Mastercraft Plug &
Play Ballast Sacs for various Mastercraft boat models. Note: The Plug & Play plumbing must be in your
boat to use these plug and play ballast sacs. (Sacs not pictured)
W040 - 2010 X-Star Ballast Sacs - 1595 lbs. (4 sacs, fittings included)
W041 - 2010 235/X35 Ballast Sacs - 1320 lbs. (4 sacs, fittings included)
W042 - 2010 215/X15 Ballast Sacs - 960 lbs. (4 sacs, fittings included)
W043 - 2010 200/X2 Ballast Sacs - 800 lbs. (4 sacs, fittings included)
W044 - 2010 245/X45 Ballast Sacs - 1220 lbs. (4 sacs, fittings included)
W045 - 2010 225/X25 Ballast Sacs - 710 lbs. (3 sacs, fittings included)
W048 - 2012 230/X30 Ballast Sacs - 1400 lbs. (4 sacs, fittings included)
W049 - 2013 X-Star Ballast Sacs - 1450 lbs. (4 sacs, fittings included)
W140 - 2013 X-46 Fat Sacs - 850 lbs. (4 sacs, includes Tsunami Pump fittings for manual filling)
W141 - 2013 X-10 Fat Sacs - 1450 lbs. (4 sacs, includes Tsunami Pump fittings for manual filling)
FLY HIGH | PRO X SERIES FITTINGS
#W730
#W739
#W731
Female Quick Connect with
chain and Cap
Quick Connect Cap
(use with W730)
Waley Plug
#W732
#W733
#W734
Garden Hose to Quick Connect
Adapter
1” Barbed End
Tsunami Pump Adapter (comes
with pump)
#W735
#W736
#W737
Perfect Union to Quick Connect
Adapter
3/4” Flow-Rite to Quick
Connect Adapter
3/4” Barbed End
#W738
#W740
#W741
Tsunami Pump Hose Adapter
(comes with pump)
3/4” Straight Flow-Rite
Connect
1 ⅛” Straight Flow-Rite
Connect
#W742
#W743
#W744
3/4” Elbow Flow-Rite Connect
1 ⅛” Flow-Rite to Quick
Connect Adapter
Check Valve System (prevents
water spillage) *
* Note: All check valves of any type slow the flow of water making it take longer to fill an empty fat sac.
NOTE: Fitting numbers; W733, W736, W737, W740,
W741, W742, W746, W743, W748, W753 and W755
are made for automatic ballast systems.
NOTE: Fitting Numbers; W733, W736, W737, W743
and W747 should be screwed into the fatsacs with
pvc cement.
#W745
#W746
#W747
3/4” Barbed Tsunami Pump
fitting
1 ⅛” Elbow Flow-Rite Connect
Sac Valve Thread for Tsunami
Pump
#W748
#W749
#W753 / #W755
1” Barb to 1 ⅛” Quick
Connect
Air release plug. For use when
manually filling, not for venting
automatic systems.
Barbed In-Line Check Valves
W753 - 1” Valve
W755 - 1 1/8” Valves
#558031-CS
#558031-HOSE
#558031-Clamp
Jabsco Control System
(Not Pictured - only need for
2007 Mastercrafts)
Black Reinforced Ballast Hose
(per foot) (fits 1” & 1 ⅛”
fittings)
316 SS Worm-Drive Hose
Clamp - 15/16” to 1-1/2” Clamp
Diameter Range
BAREFOOT INTERNATIONAL | BOOMS
Deluxe Straight Boom
#B200
Fits inboard and outboard competition ski boats with a side windshield forward of a non-tapered pylon.
Deluxe Single/Straight Contour Boom
Deluxe Universal Contour Boom
#B201
#B202
Fits inboard competition boats with a side windshield frame forward
of the pylon.
Fits inboard competition boats with a side windshield frame up to 8”
aft of the pylon.
Malibu XTI Boom
Deluxe Quad Contour Boom
#B202-XTI
#B204
Fits the Malibu XTI ski boats with retractable pylon.
Fits inboard competition boats with a side windshield frame that is
more than 8” aft of the pylon.
Deluxe Quad V-Drive Boom
Deluxe Gunnel Boom
#B204V
#B205
Fits v-drive boats with a rear mounted or retractable pylons with a
minimum of 3 inches of 2.5 inch diameter, non-tapered pylon showing. DO NOT USE ON REMOVABLE QUICK RELEASE PYLONS.
Fits any boat without a factory installed pylon.
- The best way to learn to ski & wakeboard is on the boom.
- We have booms to fit every type of boat.
Call us to find out which boom is needed for any type boat.
I have used my 30 years of experience
and training to personally design each of
the Barefoot International booms without
compromising safety. They are all built to
stay strong and won’t damage your boat.
For added safety, our booms utilize a dual
stainless steel cable system that runs all
the way to the attachment point at the bow.
There are no levers or moving parts in my
clamp designs because they can loosen or
break during use. The clamps for each boom
are extremely strong with heavy duty hardware to ensure they remain mounted firmly
to the pylon. They also have a quick release pin which makes it easy to attach and
remove the boom. Other companies use
inferior designs such as a single cable
system or straps which will wear out or even
worse, entirely fail… I have seen it happen.
By purchasing a Barefoot International
boom you are guaranteeing that you have
the highest quality, strongest, and without
a doubt, safest boom on the market.
2 Time World Barefoot Champion
BAREFOOT INTERNATIONAL | BOOMS
Fly High Tower Boom
#W206 / W207 / W208 / W209
Patented
The only boom that was designed to be mounted on the tubing of any tower. This boom is rock solid and can be stowed by pulling three quick release pins and detaching the cable system from the bow. It can also be used to train new wakeboarders at slower speeds while an instructor directs them on what to do.
(W206 fits 1 ⅞” and 2” towers / W207 fits 2¼” to 2½” towers / W208 fits the Cage Tower W2922 / W209 fits 2 ⅞” and 3” towers)
- The best way to learn to ski & wakeboard is on the boom.
- We have booms to fit every type of boat.
Call us to find out which boom is needed for any type boat.
BAREFOOT INTERNATIONAL | BOOM ACCESSORIES
Gunnel Saver (A)
Handle Attachment (E)
#B114
#B111
A
Quick Release Pin (B)
#B113 (3” ) / B113-2 (2”)
C
B
D
Height Adjuster (C)
#B107
Boom Extension (D)
Cable Protector (F)
Instructional DVD
#B108
#B144 (not pictured)
Boom Pad
DVD features World Champion Barefooter
Mike Seipel, one of the sport’s most
recognized individuals.
#B109 (not pictured)
E
Boom Bag
F
#B110
#B106 (not pictured)
Easy Footer
#B228
The Easy Footer is one of the most important learning tools you can
own because of the support it provides while training on a boom.
It’s virtually impossible to fall, allowing individuals to focus more on
the positioning of their feet and body to get the perfect glide across
the water. This product includes a DVD that demonstrates how to
properly utilize it.
Foot Skis
#B115
Made of high density polyethylene with foam cushioned strap. One size fits all. (Quick Tip: Your feet must be centered
from front to back in the Foot Skis for them to work properly. To center your feet in them make sure you use binding
lube or dish soap and that your feet and the Foot Skis are very wet by dipping them completely in the water over the
side of the boat. Then put your feet in the bindings and tap the tips of the Foot Skis on the floor of the boat to slide
your feet forward until they are centered from front to back in them.)
BAREFOOT INTERNATIONAL | ROPES & HANDLES
Poly E Plus
Barefoot Spectra Fusion
Official Barefoot Tournament Line
#B227
#B231
#B233
Our new Poly E Plus is a low stretch 100’
line with three removable 10’ extensions.
Our Spectra Fusion line is a minimal stretch
100’ line with three removable 10’ extensions.
The Official Barefoot Tournament Line offers the control
you need. It’s a non-stretch line.
#1 selling barefoot handles in the world.
Wakes Handle
Back Toe Handle
#B223
#B222
Front Toe Handle **
Starts Handle
#B219
#B224
Bare Trap Handle
Jump Handle
#B221
#B226
** Jr. Front Toe Handle B220 not pictured
“The most durable, best
gripping handles in the
world, no gimmicks”
BAREFOOT INTERNATIONAL | IRON WETSUITS & ACCESSORIES
Iron Sleeveless / Jr. Iron Sleeveless
Iron Short Sleeve
Iron Shorts
#299 / #275
#301
#455
When worn under Iron wetsuits, these shorts will make the glide
even better.
“Our suits glide
like you’re on ice”
Heater Shirt
#456
Our Iron wetsuits have double-thick flotation padding which is double-glued. This design makes it
much easier to land jumps and flips. It also aids in performing deepwater starts and tumble turns.
Wet/Dry Bag
#118
This bag has 2 separate compartments for your gear. The wet compartment allows your equipment to breath.
The 0.5mm neoprene heater shirt will keep you warm when it’s cool.
one
ost duriendly
pull
it into
ssbar
y ind board
board.
ook of
Pro X Series Crossbar Tower is the only tower that you can add to your boat that is strong enough to pull multiple tubes...
Or anything else, and it will never vibrate loose or crack your boat’s fiberglass when you do 3 key things:
1. Making sure that our supplied underplates are mounted flush.
2. Fully tighten the rear overhead adjustable cross bar with 3 guys using their bare hands after tower has been installed!
3. Double check that every nut bolt and screw is fully tightened.
The Pro X Series Tower (W2923) is completely universal and the only one constructed of stainless steel making it the strongest and most durable
tower on the market. The Quick Release pins are user friendly and make stowing and setup of the tower a simple task. Just pull six pins and the
tower folds down entirely allowing an easier fit into your garage and lift. This tower offers exclusive adjustable overhead crossbar engineering which
locks it in place and makes it as rigid as a factory installed pylon (it won’t loosen up over time). The crossbars of the tower act as an integrated board
rack that will store anything from a slalom ski to a wake surf board. This tower will never vibrate loose or crack your boat’s fiberglass when
you; make sure you flush mount our factory supplied underplates, fully tighten the rear overhead crossbar (three people tightening with
their bare hands) after tower installation, and fully tighten every
bolt
and
screw.
FLY
HIGH
| TOWERS
TIP: Keep a small tube of clear silicone grease in the boat and apply a light coat to the hitch pins
on a regular basis. This will help with installation and removal of the pins.
IMPORTANT: Call us at 561-523-1947 for quick tips on installing the Pro X Series
tower. This will help you understand the uniqueness of it and do the best
installation of the tower.
• Only universal wakeboard tower built strong enough to pull tubes
• Only stainless steel adjustable wakeboard tower
• Adjusts to fit any boat
• Folds down as low as the windshield
• Board pads on overhead crossbars double as a board rack and
provide shade when loaded with skis & boards
• Classic swoop style looks great on any boat
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com E: orders@fatsac.com
3879 N. Richards Street • Milwaukee, WI 53212
How to Weight a V-Drive Ski/
Wakeboard Boat for Wakesurfing
If you weight your V-Drive boat like this diagram shows, people will not have to learn to wakesurf
behind it, they will immediately be able to do it the first time. People that already know how to
wakesurf will be able to do bigger tricks without losing the wake.
NOTE: When weighting your boat like this, make sure to give the boat a little throttle to
bring the bow of the boat up enough when passing through wakes so they don’t wash
over the front of the boat.
This diagram shows the way to weight a V-Drive ski/wakeboard boat for
wakesurfing. Fill all factory ballast if there is any in the boat in addition to the sacs
shown on the diagram to first get the whole boat down deep in the water. Put
the Ultimate Wake Surf Sac (W718) on top of the rear seat & side seat and the
V-Drive Wake Surf Sac (W713) on top of the front seat in the open bow that you
are wakesurfing on, to get the rear corner and side of the boat you are surfing on
even deeper in the water. This will displace the most water & create the biggest
possible wake. The diagram shows it on the passenger side for wakesurfing
on the passenger side. Put the Ultimate wakesurf Sac (W718) and the V-Drive
Wakesurf Sac (W713) in the same place on the drive side for wakesurfing on the
driver side. The Ultimate Wakesurf Sac (W718) is symmetrical so the fittings are
on top and on the bottom so you can put it on the rear seat and side seat you are
wakesurfing on & have the fittings on top to fill & empty from. Some wakesurfers
like the shape of the wake better when you empty all the weight from side of the
boat opposite from wakesurfing side, but the wake will not be as large.
NOTE: It is important to hold the Ultimate Wakesurf Sac (W718) when you are
filling and emptying it but when it is full it is firm so it cannot roll off the seats
because it is shaped like a ‘L’.
NOTE: One of the great things about fat sacs is that it doesn’t matter if they are
exactly the same size and shape as the compartment or space they are going
in because they will conform. If you want maximum weight out of a space or
compartment you need to go with sacs at least as big, if not bigger then the
space or compartment so when you fill them & they conform they will fill up the
whole area and give you maximum weight out of it.
P:414-964-3668 F: 414-964-5767 W: www.fatsac.com
E: orders@fatsac.com
A: 3879 N. Richards Street • Milwaukee, WI 53212
How to Weight an Inboard Mid Engine Direct
Drive Ski Boat for Wakesurfing.
This shows the way to weigh an Inboard Mid-engine Direct Drive Ski Boat for
wakesurfing. Fill all factory ballast if the boat has any and all additional sacs shown in
the diagram. Put the 2 Fat Sacs (W707) that go in the rear of the boat as far over as
possible to the same side you are wake surfing on. Put the V-Drive Wake Surf Fat
Sac (W713) on top of the front seat in the open bow or under the bow (on closed
bow boats) on the side that you are wakesurfing on. This diagram shows the
Fat Sacs as far over on the passenger side as possible for wakesurfing on the
passenger side. Switch them to the driver side when wakesurfing on the driver
side. Some wakesurfers like the shape of the wake better when you empty all
the weight from side of the boat opposite from wakesurfing side, but the wake
will not be as large.
NOTE: When weighting your boat like this, make sure to give the boat a little
throttle to bring the bow of the boat up enough when passing through wakes
so they don’t wash over the front of the boat.
One of the great things about fat sacs is that it doesn’t matter if they are
exactly the same size and shape as the compartment or space they are going
in because they will conform. If you want maximum weight out of a space or
compartment you need to go with sacs at least as big, if not bigger then the
space or compartment so when you fill them & they conform they will fill up
the whole area and give you maximum weight out of it.
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com
3879 N. Richards Street • Milwaukee, WI 53212
E: orders@fatsac.com
How to Hook Up an Automatic Ballast System.
The Best Possible Way is by Keeping it Basic!
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com E: orders@fatsac.com
3879 N. Richards Street • Milwaukee, WI 53212
Required parts for EACH Pro X Series Fat Sac you will need the following:
1 each of (W610-P) - Jabsco Metal Ballast Puppy Pump (high volume, self-priming, reversible) with Fill/Empty Switch
25 ft of (558031-Black Hose) - Black Reinforced Bilge Hose (fits 1” & 1⅛” fittings)
2 each of (W743) - 1⅛” Quick Connect - Sac Valve Thread (use PVC Cement to screw this fitting into the Fat Sac)
2 each of (W741) - Flow-Rite 1⅛” Straight Quick Connect Socket
2 each of (W746) - Flow-Rite 1⅛” Elbow Quick Connect Socket
Diagram -Showing
6 each of (558031-Clamp)
316 Stainless Steel Worm Drive Hose Clamp 5/16” - 1 1/2” Clamp Diameter Range
How
to Hook
Up Hulls
an Automatic
Ballast
2 each
of 1” Thru
- One for the bottom
of System
the boat for Filling/Emptying; One for Venting/Overflow
The
Best
and
Easiest
Way
Adequate length of electrical wire to wire up the fill/empty switch and the Jabsco Metal Ballast Puppy Pump
• We recommend 1” Black Reinforced Bilge Hose for ALL Automatic Ballast Systems
Directions:
2 x (W746)
2 x (W743)
Thru Hull in the side of
the boat; for Venting
and Overflow
Step 1:
Run Black Reinforced Hose from the Thru Hull Fitting in the bottom of
the boat to one side of the Jabsco Pump.
Step 2:
Run Black Reinforced Hose from the other side of the Jabsco Pump to
the bottom valve on the Pro X Series Fat Sac.
Step 3:
Run Black Reinforced Hose from the highest valve on the top of the
Pro X Series Fat Sac to the Thru Hull Fitting out the side of the boat.
NOTE: The vent overflow thru hull fitting needs to be higher then
where the Vent Hose is attached to the valve on the top of the Pro X
Series Fat Sac (When Full). This is to prevent water from coming out
of the vent overflow thru hull when starting, stopping, turning, hitting
waves or leaning the boat over.
Thru Hull in the bottom of boat;
for Filling and Emptying Through
available colors
Quick Tips for using the Tsunami
Pump (W709).
diump,
The Tsunami Pump is the fastest pump that you put over the side of the
boat and plug into the cigarette lighter accessory plug to manually fill
and empty the fat sacs. It is made to go on and off the Pro X Series Fat
Sacs very fast and easy to save time. The clear hose on the Tsunami
Pump (W709) allows you to clearly see when the water is flowing good. It
also allows you to see if there are any air bubbles, weeds, sand or dirt in
it that are slowing the flow or are being pumped into your fatsac.
)
metal
t
Socket Splitter
Directions:
Step 1:
#W405
First put the Tsunami pump over the side of the boat under the water.
The socket
splitter
Step
2: is exactly what you would expect. Use this thing
to get twoThen
Tsunami
Pumps twist
flowingthe
and end
fill those
double-time.
counter
of sacs
the hose
before sticking it in the quick connect
with cap and chain on the top of the Pro X Series Fat Sac so it twists back
and holds itself in the groove.
Step 3:
Plug the Tsunami Pump into the cigarette lighter accessory plug.
12/9/07 1:06:16 PM
NOTE: To empty do the same thing except the end of the hose goes over the
side of the boat first and the pump goes on the quick connect with cap and
chain on top of the Pro X Series Fat Sac. Then push the pump down into the
sac to prime the pump.
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com E: orders@fatsac.com
3879 N. Richards Street • Milwaukee, WI 53212
The Best Possible way to learn to waterski, wakeboard, and barefoot is on the boom!
We 4HE"EST0OSSIBLEWAYTOLEARNTOWATERSKIWAKEBOARDANDBAREFOOTISONTHEBOOM
have different booms to fit every type of boat and on the tubing of every tower.
7EHAVEDIFFERENTBOOMSTOlTEVERYTYPEOFBOATANDONTHETUBINGOFEVERYTOWER
Approximately 30 years ago, Barefoot
Approximately
years ago, Barefoot
International30
manufactured
the 1st boom on
International
manufactured
the
1st
boom
onthe #1
the market and today continues
to be
the
marketfor
and
today
be the #1and/or
choice
Pro’s,
skicontinues
schools,tofamilies,
choice for Pro’s, ski schools, families, and/or
anybody wanting to learn wakeboarding and
anybody wanting to learn wakeboarding and
water skiing. Our booms fit all boats and are
water skiing. Our booms fit all boats and are
item
needed
to make
any boat
byby
farfar
thethe
oneone
item
needed
to make
any boat
the
ultimate
learning
for wakeboarding
the
ultimate
learning
tooltool
for wakeboarding
and and
skiing.
guarantee
willless
do tubing
less tubing
skiing.
WeWe
guarantee
you you
will do
and
enjoy
your
time
on
the
water
100%
and enjoy your time on the water 100%
more more
while
saving
50%
on wasted
You can
while
saving
50%
on wasted
gas. gas.
You can
teach
or or
learn
everything
on the
in under
teach
learn
everything
on water
the water
in under
1515
minutes.
minutes.
Call
usus
at at
1-414-964-3668
to find
out which
Call
1-414-964-3668
to find
out which
one fits your boat or tower.
one fits your boat or tower.
Tower Boom Models:
W206
1 7/8” and 2” Towers
Tower
Boom
Models:
2¼”
to 2”
2½”Towers
Towers
W206W207
- -1 7/8”
and
W208
Fits
Cage
(W2922)
W207 - 2¼” to 2½” Towers
W209
Fits 2Ǭ”
and 3” Towers
W208 - Fits Cage
(W2922)
W209 - Fits 2⅞” and 3” Towers
Deluxe Boom Models:
B200
Deluxe Straight
Boom
Deluxe
Boom
Models:
B201
Single/Straight
Contour Boom
B200- - Deluxe
Deluxe
Straight Boom
B202
Deluxe
Universal
Contour
B201 - Deluxe Single/StraightBoom
Contour Boom
B202-XTI
Malibu
XTI
Boom
(boat
with
retractable
B202 - Deluxe Universal Contour
Boom Pylon)
B204 Deluxe Quad Contour Boom
B202-XTI - Malibu XTI Boom (boat with retractable Pylon)
B204V Deluxe Quad V-Drive Boom
B204 - Deluxe Quad Contour Boom
B205 Deluxe Gunnel Mount Boom
B204V - B205 - Deluxe Quad V-Drive Boom
Deluxe Gunnel Mount Boom
4HE"EST0OSSIBLEWAYTOLEARNTOWATERSKIWAKEBOARDANDBA
Center Pylon Boom Installation Instructions.
7EHAVEDIFFERENTBOOMSTOlTEVERYTYPEOFBOATANDONTHETU
Approxim
Internatio
the marke
choice fo
anybody
water skii
by far the
the ultima
skiing. We
and enjoy
while sav
teach or l
15 minute
The Best Possible way to learn to ski, barefoot and wakeboard is on the boom!
WARNING: FAILURE TO ADHERE TO ALL WARNINGS COULD CAUSE DAMAGE TO EQUIPMENT
OR VEHICLE, PERSONAL INJURY OR EVEN DEATH. BE AWARE OF YOUR SURROUNDINGS AND
ALWAYS STAY CLEAR OF BRIDGES, DOCKS AND ANY OTHER OBSTACLES • DO NOT USE THE BOOM
WITHOUT THE CABLES ATTACHED TO THE BOW OF THE BOAT • DO NOT TOW THE BOAT WITH THE
BOOM INSTALLED • DO NOT USE TO PULL TUBES, KITES, PARA SAILORS OR STRANDED BOATS • BE
SURE TO CHECK ALL HARDWARE, CLAMPS AND CABLES FOR WEAR AND PROPER INSTALLATION
PRIOR TO EACH USE.
WARNING: THE USE OF THIS PRODUCT INVOLVES INHERENT RISKS OF INJURY OR DEATH.
Call us a
one fits y
Tower Boom Models:
Deluxe Boom Mo
W206 1 7/8” and 2” Towers
B200 Deluxe St
TO REDUCE THESE RISKS THE INDIVIDUAL MUST ALWAYS STAY WITHIN THEIR LIMITS AND AT
W207 2¼” to 2½” Towers
B201 Deluxe Si
Fits Cage (W2922)
B202 Deluxe U
SPEEDS THAT DO NOT EXCEED THEIR LEVEL OF SKILL. THIS PRODUCT IS A TRAINING AID FOR ALL TYPESW208
OF
SKIING
AND
SHOULD
ONLY
BE
USED
W209 Fits 2Ǭ” and 3” Towers
B202-XTI - Malibu XT
FOR THAT PURPOSE. DO NOT HANG OFF THE BOOM WHEN THE BOAT IS IN MOTION UNLESS THE INTENT IS TO SKI. THE DRIVER OF THE BOAT SHOULDB204 - Deluxe Q
B204V Deluxe Q
B205 Deluxe G
ALWAYS FOCUS THEIR ATTENTION ON THE SURROUNDINGS, NOT THE SKIER.
7-
Hook the carabineer on the cables to the boat’s trailer under-bow eye hook.
NOTE- For the next step, the cables must have no slack hanging down.
8- Pull any slack out of the cables until they are snug. Make sure the cable loop at the end is approximately 1½” - 2” in
diameter. Tighten all 8 set screws on the cable clamp with provided allen wrench. Be sure you tighten them until they are
extremely tight.
9- Slide the cable pad over the cables and connect loop strap through the carabineer. Tuck any excess cable back into
the cable pad.
TO REMOVE THE BOOM: SIMPLY UNHOOK THE CABLES FROM THE BOAT, REMOVE THE OUTSIDE
SECTION, AND REMOVE THE INSIDE SECTION USING THE QUICK RELEASE PIN.
1. Read through all directions and warnings completely before installing this product.
Important: The Boom clamp must be installed on the non-tappered portion of the pylon.
2. Attach the boom clamp to the pylon using two bolts and washers. Be sure you tighten the
bolts evenly, only turning them a couple turns at a time and alternating between them. Don’t
tighten the bolts completely because you will be adjusting the clamp in a later step.
3. Pin the inside section of the boom to the clamp using the quick release pin.
4. Slide the outside boom section into the inside boom section until the push pin snaps entirely
into its hole.
Note: For the next step, the boom should be angled slightly up and forward.
5. Adjust the boom height so it will be positioned chest-high on an average height person when
in use.
6. Have someone hold the boom in position at the desired angle while you finish tightening the
bolts on the clamp. Be sure you tighten them evenly and firmly.
7. Hook the carabineer on the cables to the boat’s trailer under-bow eye hook.
Note: For the next step, the cables must have no slack hanging down.
8. Pull any slack out of the cables until they are snug. Make sure the cable loop at the end is approximately 1½” - 2” in diameter.
Tighten all 8 set screws on the cable clamp with provided allen wrench. Be sure you tighten them until they are extremely tight.
9. Slide the cable pad over the cables and connect loop strap through the carabineer. Tuck any excess cable back into the cable pad.
Boom Removal: To remove the Boom simply unhook the cables from the boat, remove the outside section, and remove the inside
section using the quick release pin. The clamp can remain on the pylon while the boom is not being used.
THE CLAMP CAN REMAIN ON THE PYLON WHILE THE BOOM IS NOT BEING USED.
YOU MUST CHECK ALL 8 SET SCREWS PRIOR
TO EACH USE TO ENSURE THAT THEY ARE TIGHT.
FAILURE TO DO SO COULD RESULT IN DAMAGE TO
EQUIPMENT OR PERSONAL INJURY
CABLE CLAMP
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com E: orders@fatsac.com • 3879 N. Richards Street • Milwaukee, WI 53212
Gunnel Mount Boom Installation Instructions
The Best Possible way to learn to ski, barefoot and wakeboard is on the boom!
WARNING: FAILURE TO ADHERE TO ALL WARNINGS COULD CAUSE DAMAGE TO EQUIPMENT OR VEHICLE, PERSONAL INJURY OR EVEN DEATH.
BE AWARE OF YOUR SURROUNDINGS AND ALWAYS STAY CLEAR OF BRIDGES, DOCKS AND ANY OTHER OBSTACLES • DO NOT USE THE BOOM WITHOUT
THE CABLES ATTACHED TO THE BOW OF THE BOAT • DO NOT TOW THE BOAT WITH THE BOOM INSTALLED • DO NOT USE TO PULL TUBES, KITES, PARA
SAILORS OR STRANDED BOATS • BE SURE TO CHECK ALL HARDWARE, CLAMPS AND CABLES FOR WEAR AND PROPER INSTALLATION PRIOR TO EACH
USE.
WARNING: THE USE OF THIS PRODUCT INVOLVES INHERENT RISKS OF INJURY OR DEATH. TO REDUCE THESE RISKS THE INDIVIDUAL MUST ALWAYS
STAY WITHIN THEIR LIMITS AND AT SPEEDS THAT DO NOT EXCEED THEIR LEVEL OF SKILL. THIS PRODUCT IS A TRAINING AID FOR ALL TYPES
OF SKIING AND SHOULD ONLY BE USED FOR THAT PURPOSE. DO NOT HANG OFF THE BOOM WHEN THE BOAT IS IN MOTION UNLESS THE INTENT
IS TO SKI. THE DRIVER OF THE BOAT SHOULD ALWAYS FOCUS THEIR ATTENTION ON THE SURROUNDINGS, NOT THE SKIER.
1. Read through all directions and warnings completely before installing this product.
Important: The most important thing to keep in mind when installing the Gunnel Mount Boom is that it’s positioned so the skier is
out of the side spray produced by the boat’s hull.
2. The boom is made up of three separate pieces; the gunnel extension, inside section and outside section. Pin the gunnel
extension to the inside section using the lock pin (be sure you secure it with the snap wire).
3. Slide the outside section of the boom into the inside section until the alignment pin snaps into place.
Note: You will need three people and some towels for the next step.
4. Take the boat and boom out onto the lake. Drive at speeds that you intend to pull skiers while
two friends experiment with the placement of the boom. Use the towels as padding to keep
the boom from damaging the gunnels of the boat. The goal at this point is to position the
boom so the skier is out of the side spray produced by the boat’s hull.
5. Once you have determined the best placement for the boom, note where it will be installed
and head back to shore.
6. Check behind both gunnels where you plan to drill and make sure that there are no
obstructions such as throttle cables or wires. You may have to reconsider the boom
placement if you are not positive that there are no obstructions.
ADJUSTING THE LEVEL OF THE BOOM: Depending on the design of your boat, you may
have to adjust where you mount the clamp. The goal here is to have the boom at chest level
for an average height person. Don’t’ forget that the boom will be slightly higher when the
boat is moving and on plane. To adjust the level of the boom, move the clamp up or down
accordingly. Due to the many types and shapes of boats, there is no way for us to describe a
predetermined placement for the clamp. If you have any questions, please contact us prior to
proceeding.
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com E: orders@fatsac.com • 3879 N. Richards Street • Milwaukee, WI 53212
Gunnel Tower Boom Installation Instructions (continued).
7. Use the boom clamp to mark where you will be drilling the holes to mount it. Drill through your marks and mount the clamp to the
gunnel using 4 screws, backing plate, washers and locking nuts. Be sure you tighten them firmly. (Fig. 1)
8. The boom should still be put together from step 4. Use the 1/2” x 3” bolt to temporarily pin the boom to the clamp. Rest the boom
on the opposite gunnel and use the u-bracket to mark where you will need to drill. Remove the boom from the boat.
9. Drill your holes and install the u-bracket using the 4 screws, backing plate, washers and lock nuts. The u-bracket stays mounted to
the boat permanently so be sure you tighten the bolts firmly. (Fig. 2)
10.Slide the boom through the u-bracket and pin it to the clamp using the 1/2” x 3” bolt. Secure the bolt using the flat washer and
wing nut. Tighten it as tight as you can with your hands.
11.Hook the carabineer on the cables to the boat’s trailer under-bow eye hook.
12.Pull any slack out of the cables until they are snug and the boom is pressed against the front of the u-bracket. Make sure the cable
loop at the end is approximately 1½” - 2” in diameter. Tighten all 8 set screws on the cable clamp with provided allen wrench. Be
sure you tighten them until they are extremely tight.
13.Slide the cable pad over the cables and connect loop strap through the carabineer. Tuck any excess cable back into the cable pad.
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com E: orders@fatsac.com • 3879 N. Richards Street • Milwaukee, WI 53212
Tower Boom Installation Instructions.
The Best Possible way to learn to ski, barefoot and wakeboard is on the boom!
WARNING: FAILURE TO ADHERE TO ALL WARNINGS COULD CAUSE DAMAGE TO EQUIPMENT OR VEHICLE, PERSONAL INJURY OR EVEN
DEATH. BE AWARE OF YOUR SURROUNDINGS AND ALWAYS STAY CLEAR OF BRIDGES, DOCKS AND ANY OTHER OBSTACLES • DO NOT USE THE BOOM
WITHOUT THE CABLES ATTACHED TO THE BOW OF THE BOAT • DO NOT TOW THE BOAT WITH THE BOOM INSTALLED • DO NOT USE TO PULL TUBES,
KITES, PARA SAILORS OR STRANDED BOATS • BE SURE TO CHECK ALL HARDWARE, CLAMPS AND CABLES FOR WEAR AND PROPER INSTALLATION
PRIOR TO EACH USE.
WARNING: THE USE OF THIS PRODUCT INVOLVES INHERENT RISKS OF INJURY OR DEATH. TO REDUCE THESE RISKS THE INDIVIDUAL MUST
ALWAYS STAY WITHIN THEIR LIMITS AND AT SPEEDS THAT DO NOT EXCEED THEIR LEVEL OF SKILL. THIS PRODUCT IS A TRAINING AID FOR ALL
TYPES OF SKIING AND SHOULD ONLY BE USED FOR THAT PURPOSE. DO NOT HANG OFF THE BOOM WHEN THE BOAT IS IN MOTION UNLESS THE
INTENT IS TO SKI. THE DRIVER OF THE BOAT SHOULD ALWAYS FOCUS THEIR ATTENTION ON THE SURROUNDINGS, NOT THE SKIER.
1. Read through all directions and warnings completely before installing this product.
Note: If your tower is smaller in diameter, use the supplied bushings with the clamp (Figure 3). This applies to all clamps. If the
bushings don’t fit perfectly flush, please contact us.
Note: On boats with a single bar tower such as the MasterCraft line, the Tower Boom will install differently. If your tower has a single
bar tower design, perform step 2a.
2. BOOM CLAMP ASSEMBLY - Attach the boom clamp to the rear tower leg. Position it on a straight portion of the tower as close
to the base as possible. Don’t tighten the bolts completely (Figures 1 & 3).
2a.Attach the boom clamp to the front tower leg. Position it as close to the base as possible. Don’t tighten the bolts completely
(Figures 2 & 3).
3. There are two types of clamps for the support braces (Figure 4). Attach a hitch pin clamp 2-3 feet above the boom clamp. Don’t
tighten the bolts completely because you will need to adjust the clamp.
Note: On boats with a single bar tower design, perform step 4a.
4. Attach the other hitch pin clamp to the front tower leg 2-3 feet above the boat’s gunnel. Don’t completely tighten the bolts
(Figure 1).
4a.Attach the other hitch pin clamp 1 foot above the first hitch pin clamp on the same tower leg (Figure 2). Don’t completely tighten
the bolts.
5. Attach the remaining two clamps to the inside section of the boom 3 feet out. Don’t tighten them completely.
6. Pin both braces to the clamps on the tower using the hitch pins.
7. Use the quick release pin to attach the inside section of the boom to the boom clamp. Be sure the ball on the quick release pin is
all the way through the clamp.
8. Bolt the braces to the clamps on the boom. You may have to adjust the length of the brace so it will reach. To adjust the length
of a brace, simply turn the inside section of the brace.
Tower Boom Installation Instructions (continued).
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com E: orders@fatsac.com
3879 N. Richards Street • Milwaukee, WI 53212
Note: For the next step, the boom should be chest high of an average height skier. If adjustments are needed while skiing, moving
people in the boat will shift the weight and raise or lower the boom.
9. Now you must adjust everything while someone holds the boom in position. The boom must be angled slightly forward and up. The
braces must be between 3-5 feet in length and have a minimum angle of 30˚ above horizontal.
10.After everything is set to the correct position, tighten the
FIG. 1
FIG. 2
hardware on all clamps. Start with the main boom clamp,
then the clamps on the tower, and finally the clamps on the
boom. Tighten the bolts firmly.
Note: For the next step, if you own a MasterCraft with the
pickle-fork bow design you will attach the carabineer to the
boat’s deck clevis (Figure 5).
11.Slide the outside boom section into the inside boom section
until the push pin snaps entirely into the hole. Hook the
carabineer on the cables to the boat’s trailer under-bow eye
hook.
Note: For the next step, the cables must have no slack hanging
FIG. 3
FIG. 4
down. If they are loose the Tower Boom will put too much
stress on the tower when in use.
12.Pull any slack out of the cables until they are snug. Make
sure the cable loop at the end is approximately 1½” - 2” in
diameter. Tighten all 8 set screws on the cable clamp with
provided allen wrench (Figure 6). Be sure you tighten them
until they are extremely tight.
13.Slide the cable pad over the cables and connect loop strap
through the carabineer. Tuck any excess cable back into the
cable pad.
To stow the Tower Boom: (1) Disconnect the cables from
FIG. 5
FIG. 6
the boat. (2) Telescope the outside boom section into the
inside section. (3) Pull the pins from the braces and raise the
boom. (4) Pull the quick release pin from the boom clamp. (5)
Remove the boom until its next use.
We recommend that you keep a small tube of clear silicone
grease in the boat and occasionally apply a light coat to the
pins. This will help keep them in good working condition and
ease their installation and removal.
CABLE CLAMP
V-Drive Boom Installation Instructions.
The Best Possible way to learn to ski, barefoot and wakeboard is on the boom!
WARNING: FAILURE TO ADHERE TO ALL WARNINGS COULD CAUSE DAMAGE TO EQUIPMENT OR VEHICLE, PERSONAL INJURY OR EVEN
DEATH. BE AWARE OF YOUR SURROUNDINGS AND ALWAYS STAY CLEAR OF BRIDGES, DOCKS AND ANY OTHER OBSTACLES • DO NOT USE THE BOOM
WITHOUT THE CABLES ATTACHED TO THE BOW OF THE BOAT • DO NOT TOW THE BOAT WITH THE BOOM INSTALLED • DO NOT USE TO PULL TUBES,
KITES, PARA SAILORS OR STRANDED BOATS • BE SURE TO CHECK ALL HARDWARE, CLAMPS AND CABLES FOR WEAR AND PROPER INSTALLATION
NOTE- Forthenextstep,theboomshouldbeangledslightlyupandforward.
PRIOR TO EACH USE.
5-
Adjust the boom height so it will be positioned chest-high on an average height person when in use.
WARNING: THE USE OF THIS PRODUCT INVOLVES INHERENT RISKS OF INJURY
ORsomeone
DEATH.
TO
REDUCE
THE
MUST
6- Have
hold the
boom
in position atTHESE
the desiredRISKS
angle. When
it’s in INDIVIDUAL
a suitable position, finish
tightening the
bolts evenly and firmly.
ALWAYS STAY WITHIN THEIR LIMITS AND AT SPEEDS THAT DO NOT EXCEED THEIR LEVEL OF SKILL. THIS PRODUCT IS A TRAINING AID FOR ALL
- Hook the carabineer on the cables to the boat’s trailer under-bow eye hook.
TYPES OF SKIING AND SHOULD ONLY BE USED FOR THAT PURPOSE. DO NOT HANG 7OFF
THE BOOM WHEN THE BOAT IS IN MOTION UNLESS THE
NOTE- Forthenextstep,thecablesmusthavenoslackhangingdown.
INTENT IS TO SKI. THE DRIVER OF THE BOAT SHOULD ALWAYS FOCUS THEIR ATTENTION ON THE SURROUNDINGS, NOT THE SKIER.
8- Pull any slack out of the cables until they are snug. Make sure the cable loop at the end is approximately 1½” - 2” in
diameter. Tighten all 8 set screws on the cable clamp with provided allen wrench. Be sure you tighten them until they are
extremely tight.
1. Read through all directions and warnings completely before installing this product.
9- of
Slide the
the cable
pad over the cables and connect loop strap through the carabineer. Tuck any excess cable back into
Important: The Boom clamp must be installed on the non-tappered portion
pylon.
the cable pad.
Note: For the next step, if your boat has a retractable pylon you must pull up on the pylon and push the clamp body down into the
10- The last thing you need to do is attach a section of rope from the boom to the rear of the boat. This keeps the boom
vinyl of the sun deck. The clamp is rounded so it will not damage the vinyl
on your
boat.
cutrunsaalong
hole
in(seeaillustration
rag and
slide
from recoiling
forward when
the skierYou
falls off can
it. Make also
sure the rope
gunnel
for details).
it over the pylon before you install the clamp. This will help keep the clamp
from rubbing
onUNHOOKTHE
the vinyl.CABLES
For questions
on
this, call
TO REMOVETHE
BOOM: SIMPLY
FROMTHE BOAT,
REMOVETHE
OUTSIDE
SECTION,DISCONNECTTHEROPETOTHEREAROFTHEBOAT,ANDREMOVETHEINSIDESECTION
us during normal business hours.
USINGTHEQUICKRELEASEPIN.
2. Attach the V-Drive boom clamp to the pylon using two bolts, washers, spacers, and three main clamp pieces (see illustration for
THECLAMPCANREMAINONTHEPYLONWHILETHEBOOMISNOTBEINGUSED.
details). Be sure you tighten the bolts evenly, only turning them a
couple turns at a time and alternating between them. Don’t tighten
YOU MUST CHECK ALL 8 SET SCREWS PRIOR TO EACH USE TO
the bolts completely because you will be adjusting the clamp in a
ENSURETHATTHEYARETIGHT.FAILURETODOSOCOULDRESULT
INDAMAGETOEQUIPMENTORPERSONALINJURY
later step.
3. Pin the inside section of the boom to the clamp using the quick
release pin.
4. Slide the outside boom section into the inside boom section until
the push pin snaps entirely into its hole.
Note: For the next step, the boom should be angled slightly up and
forward.
5. Adjust the boom height so it will be positioned chest-high on an
average height person when in use.
6. Have someone hold the boom in position at the desired angle.
When it’s in a suitable position, finish tightening the bolts evenly
and firmly.
CABLE CLAMP
V-Drive Boom Installation Instructions (continued).
P: 414-964-3668 F: 414-964-5767 W: www.fatsac.com E: orders@fatsac.com
3879 N. Richards Street • Milwaukee, WI 53212
7. Hook the carabineer on the cables to the boat’s trailer
under-bow eye hook.
Note: For the next step, the cables must have no slack
hanging down.
8. Pull any slack out of the cables until they are snug. Make
sure the cable loop at the end is approximately 1½” - 2” in
diameter. Tighten all 8 set screws on the cable clamp with
provided allen wrench. Be sure you tighten them until they
are extremely tight.
9. Slide the cable pad over the cables and connect loop
strap through the carabineer. Tuck any excess cable back
into the cable pad.
10.The last thing you need to do is attach a section of rope
from the boom to the rear of the boat. This keeps the
boom from recoiling forward when the skier falls off it.
Make sure the rope runs tight up touching the gunnel (see
illustration for details).
U-BRACKET
Boom Removal: Simply unhook the cables from the boat,
remove the outside section, disconnect the rope from
the rear of the boat, and remove the inside section using
the quick release pin. The clamp can remain on the pylon
while the boom is not being used.
THE PLACEMENT OF THE V-DRIVE BOOM CLAMP IS DEPENDENT UPON THE PYLON YOU ARE MOUNTING IT TO.
AT LEAST 3 INCHES OF A NON-TAPERED SURFACE WILL BE NEEDED TO ATTACH THE CLAMP BELOW THE TAPERED
PORTION IF THERE IS LESS THAN 3 INCHES, THE CLAMP MUST BE MOUNTED HIGHER ON THE PYLON.
SUPRA / MOOMBA
RETRACTABLE PYLON
Tips:
1. To lower the boom for shorter skiers, use the Boom Height
Adjuster (part # B107).
2. To help position the skier out of the spray from the boat,
use the Boom Extension (part # B110).
MALIBU
RETRACTABLE PYLON
OPTIONAL
U-BRACKET
PLACEMENT
U-BRACKET
PLACEMENT
3” or greater
above vinyl
less than 3”
above vinyl