Datasheet
Small Form-factor Pluggable (SFP)
Optical Module Cartridges (Ethernet)
For Densité Frames and Grass Valley/Telecast Standalone Fiber Products
The Small Form-factor Pluggable (SFP) optical module cartridges are small, hot-pluggable devices used
to provide Ethernet fiber connectivity to IP-based
products from either a Densité frame or standalone
fiber products. Multimode fiber links can be used for
links of a few hundred meters, while single-mode fiber
links can be used at distances up to 10 kilometer and
over (dependent on SFP type) without degrading signal quality.
All SFP optical module cartridges that are available
from by Grass Valley, a Belden Brand, are RoHS
compliant.
TABLE OF CONTENTS
SFP-ETH-10-RT-CXX-LC........................................ 2
CWDM / 1.25 Gb/s Single Mode SFP Transceiver
SFP-ETH10G-RT-S13-LC....................................... 9
1310 nm / 10.3 Gb/s Single Mode SFP Transceiver
SFP-ETH-10-RT-W13-LC........................................ 4
1310 nm / 1.25 Gb/s Single Mode SFP Transceiver
SFP-ETH10G-RT-CXX-LC.................................... 10
CWDM / 10.3 Gb/s Single Mode SFP Transceiver
SFP-ETH-10-RT-W15-LC........................................ 5
1310 nm / 1.25 Gb/s Single Mode SFP Transceiver
SFP-ETH10G-RT-W27-LC.................................... 12
WDM / 10.3 Gb/s Single Mode SFP Transceiver
SFP-ETH-10-S13-LC.............................................. 6
1310 nm / 1.25 Gb/s Single Mode SFP Transceiver
SFP-ETH10G-RT-W33-LC.................................... 13
WDM / 10.3 Gb/s Single Mode SFP Transceiver
SFP-ETH-RT-M85-LC............................................. 7
850 nm / 1.25 Gb/s Multimode SFP Transceiver
Global Services..................................................... 14
SFP-ETH10G-RT-M85-LC....................................... 8
850 nm / 10.3 Gb/s Multimode SFP Transceiver
www.grassvalley.com
1
SFP-ETH-10-RT-CXX-LC
CWDM / 1.25 Gb/s Single Mode SFP Transceiver
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products.
The SFP-ETH-10-RT-CXX-LC is a single mode optical transceiver that supports signals up to 1.25 Gb/s for bidirectional serial data communications
such as 1000BASE-ZX. It is equipped with Duplex LC connectors.
KEY FEATURES
• SFP MSA Compliant
• 1.25 Gb/s:
–– 1000BASE-ZX compliant
• CWDM Multiple Quantum Well DFB laser Transmitter
• RoHS-6 compliant
• Hot pluggable
• Diagnostic Monitoring Interface (DMI)
SPECIFICATIONS
Transmitter Specifications (0°C < Tc < 70°C, 3.13V < Vcc < 3.47V)
Parameter
Symbol
Min.
Typ.
Max.
Units
Notes
Po
0
—
5
dBm
Output power is power coupled into a
9/125 µm single mode fiber
l
lc – 6.5
lc
lc + 6.5
nm
ITU-T G.694.2 CWDM wavelength from
1271 nm to 1611 nm, each step 20 nm
—
1
nm
-20 dB width
Optical
Optical Transmit Power
Output Center Wavelength
Output Spectrum Width
Δl
—
SMSR
30
Extinction Ratio
ER
9
Optical Rise Time
tr
Side Mode Suppression Ratio
Optical Fall Time
Relative Intensity Noise
dB
—
—
dB
260
ps
20% to 80% values
20% to 80% values
tf
260
ps
RIN
-120
dB/Hz
Electrical
Data Input Current – Low
IIL
Data Input Current – High
IIH
Differential Input Voltage
VIH – VIL
-350
mA
0.5
350
mA
2.4
V
Peak-to-peak
There is an internal 4.7 kΩ to 10 kΩ
pull-up resistor to VccTX
TX Disable Input Voltage – Low
VTDIS, L
0
0.5
V
TX Disable Input Voltage – High
VTDIS, H
2.0
Vcc
V
TX Disable Assert Time
TX Disable De-assert Time
TASSERT
10
ms
TDEASSERT
1
ms
TX Fault Output Voltage – Low
TFaultL
0
0.5
V
TX Fault Output Voltage – High
TFaultH
2.0
Vcc+0.3
V
-24
dBm
Open collector compatible, 4.7 kΩ to
10 kΩ pull-up to Vcc (host supply voltage)
Receiver Specifications (0°C < Tc < 70°C, 3.13V < Vcc < 3.47V)
Optical
Sensitivity
Sens
Measured at 27-1 PRBS at BER 1E-12
Maximum Input Power
Pin
-3
Signal Detect – Asserted
Pa
—
—
-24
dBm
dBm
Transition: low to high
Signal Detect – De-Asserted
Pd
-36
—
—
dBm
Transition: high to low
Signal detect – Hysteresis
1.0
—
Wavelength of Operation
1100
—
1620
nm
dB
Electrical
Differential Output Voltage
VOH –VOL
0.6
2.0
V
Output LOS Voltage – Low
VOL
0
0.5
V
Output LOS Voltage – High
VOH
2.0
Vcc+0.3
V
www.grassvalley.com
Open collector compatible, 4.7 kΩ to
10 kΩ pull-up to Vcc (Host Supply Voltage)
2
SFP-ETH-10-RT-CXX-LC
ORDERING
Part number
SFP-ETH-10-RT-CXX-LC
Bit Rate
(Gb/s)
1000
BASE
Wavelength
(nm)
Package
Temp. (°C)
Tx Power
(dBm)
Rx Sens.
(dBm)
RoHS
Compliant
1.25
ZX
CWDM*
SFP with DMI
0 to 70
0 to 5
-24
Yes
*CWDM: 18 Wavelengths from 1271 nm to 1611 nm, each step 20 nm (0 to 70°C).
Value for
-CXX
Central Wavelength (nm)
Min.
Typ.
Max.
Clasp Color Code
Value for
-CXX
Central Wavelength (nm)
Min.
Typ.
Max.
Clasp Color Code
-C27
1264.5
1271
1277.5
Light Purple
-C45
1444.5
1451
1457.5
Yellow Orange
-C29
1284.5
1291
1297.5
Sky Blue
-C47
1464.5
1471
1477.5
Gray
-C31
1304.5
1311
1317.5
Yellow Green
-C49
1484.5
1491
1497.5
Violet
-C33
1324.5
1331
1337.5
Yellow Ocher
-C51
1504.5
1511
1517.5
Blue
-C35
1344.5
1351
1357.5
Pink
-C53
1524.5
1531
1537.5
Green
-C37
1364.5
1371
1377.5
Beige
-C55
1544.5
1551
1557.5
Yellow
-C39
1384.5
1391
1397.5
White
-C57
1564.5
1571
1577.5
Orange
-C41
1404.5
1411
1417.5
Silver
-C59
1584.5
1591
1597.5
Red
-C43
1424.5
1431
1437.5
Black
-C61
1604.5
1611
1617.5
Brown
Note: Only connections with patch cords with PC or UPC connectors are supported.
www.grassvalley.com
3
SFP-ETH-10-RT-W13-LC
1-Fiber 1310 nm / 1.25 Gb/s Single Mode SFP Transceiver
KEY FEATURES
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products.
The SFP-ETH-10-RT-W13-LC is a single mode optical transceiver that supports signals up to 1.25 Gb/s for bidirectional serial data communications
such as 1000BASE-BX10. It is equipped with Simplex LC connectors.
SPECIFICATIONS
• 1-Fiber Bidirectional Transceiver
• SFP MSA Compliant
• 1.25 Gb/s:
–– 1000BASE-BX10 compliant
• 1310 nm Multiple Quantum Well LD Transmitter
• 1550 nm receiver
• Link distance up to 10 km at 1.25 Gb/s
• RoHS-6 compliant
• Hot pluggable
• Diagnostic Monitoring Interface (DMI)
Transmitter Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)
Parameter
Symbol
Min.
Typ.
Max.
Units
Notes
Po
-9
—
-3
dBm
Output power is power coupled into
a 9/125 µm single mode fiber
Optical
Optical Transmit Power
Output Center Wavelength
l
1260
1310
1360
nm
Output Spectrum Width
Δl
—
—
2.5
nm
Extinction Ratio
ER
9
—
—
dB
Optical Rise Time
tr
260
ps
20% to 80% values
Optical Fall Time
tf
260
ps
20% to 80% values
RIN
-120
dB/Hz
Relative Intensity Noise
RMS (s)
Electrical
Data Input Current – Low
IIL
Data Input Current – High
IIH
Differential Input Voltage
VIH - VIL
-350
µA
0.5
350
µA
2.4
V
Peak-to-peak
There is an internal 4.7 kΩ to 10 kΩ
pull-up resistor to VccTX
TX Disable Input Voltage – Low
VTDIS, L
0
0.5
V
TX Disable Input Voltage – High
VTDIS, H
2.0
Vcc
V
TX Disable Assert Time
TX Disable De-assert Time
TASSERT
10
µs
TDEASSERT
1
ms
TX Fault Output Voltage – Low
TFaultL
0
0.5
V
TX Fault Output Voltage – High
TFaultH
2.0
Vcc+0.3
V
-20
dBm
Open collector compatible, 4.7 kΩ
to 10 kΩ pull-up to Vcc (Host Supply
Voltage)
Receiver Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)
Optical
Sensitivity
Sens
dBm
Measured at 27-1 PRBS at
BER 1E-12
Maximum Input Power
Pin
-3
Signal Detect – Asserted
Pa
—
—
-20
dBm
Transition: low to high
Signal Detect – De-Asserted
Pd
—
dBm
Transition: high to low
-31
—
Signal detect – Hysteresis
1.0
—
Wavelength of Operation
1480
—
dB
1580
nm
2.0
V
At least 30 dB optical isolation for
the wavelength 1260 to 1360 nm
Electrical
Differential Output Voltage
VOH –VOL
0.6
Output LOS Voltage – Low
VOL
0
0.5
V
Output LOS Voltage – High
VOH
2.0
Vcc+0.3
V
Open collector compatible, 4.7 kΩ
to 10 kΩ pull-up to Vcc (Host Supply
Voltage)
Bit Rate
(Gb/s)
1000 BASE
Distance
(km)
Tx (nm)
Rx (nm)
Package
Temp. (°C)
Tx Power
(dBm)
Rx Sens.
(dBm)
RoHS
Compliant
1.25
BX10
10
1310
1550
SFP with
DMI
0 to 70
-9 to -3
-20
Yes
ORDERING
Part number
SFP-ETH-10-RT-W13-LC
Note: Only connections with patch cords with PC or UPC connectors are supported.
www.grassvalley.com
4
SFP-ETH-10-RT-W15-LC
1310 nm / 1.25 Gb/s Single Mode SFP Transceiver
KEY FEATURES
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products.
The SFP-ETH-10-RT-W15-LC is a single mode optical transceiver that supports signals up to 1.25 Gb/s for bidirectional serial data communications
such as 1000BASE-BX10. It is equipped with Simplex LC connectors.
SPECIFICATIONS
• 1-Fiber Bidirectional Transceiver
• SFP MSA compliant
• 1.25 Gb/s:
–– 1000BASE-BX10 compliant
• 1550 nm DFB LD Transmitter
• 1310 nm receiver
• Link distance up to 10 km at 1.25 Gb/s
• RoHS compliant
• Hot pluggable
• Diagnostic Monitoring Interface (DMI)
Transmitter Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)
Parameter
Symbol
Min.
Typ.
Max.
Units
Notes
Po
-9
—
-3
dBm
Output power is power coupled into a
9/125 µm single mode fiber
l
1480
1580
nm
1
nm
Optical
Optical Transmit Power
Output Center Wavelength
Output Spectrum Width
Δl
—
SMSR
30
Extinction Ratio
ER
9
Optical Rise Time
Optical Fall Time
Side Mode Suppression Ratio
Relative Intensity Noise
—
-20 dB width
dB
—
—
dB
tr
260
ps
20% to 80% values
tf
260
ps
20% to 80% values
RIN
-120
dB/Hz
Electrical
Data Input Current – Low
IIL
-350
µA
Data Input Current – High
IIH
350
µA
Differential Input Voltage
VIH -VIL
0.5
2.4
V
Peak-to-peak
TX Disable Input Voltage – Low
VTDIS, L
0
0.5
V
TX Disable Input Voltage – High
VTDIS, H
2.0
Vcc
V
There is an internal 4.7 kΩ to 10 kΩ
pull-up resistor to VccTX
TX Disable Assert Time
TASSERT
10
µs
TX Disable De-assert Time
1
ms
TX Fault Output Voltage – Low
TDEASSERT
TFaultL
0
0.5
V
TX Fault Output Voltage – High
TFaultH
2.0
Vcc+0.3
V
-20
dBm
Open collector compatible, 4.7 kΩ
to 10 kΩ pull-up to Vcc (Host Supply
Voltage)
Receiver Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)
Optical
Sensitivity
Sens
dBm
Measured at 27-1 PRBS at BER 1E-12
@1300 nm
Maximum Input Power
Pin
-3
Signal Detect – Asserted
Pa
—
—
-20
dBm
Transition: low to high
Signal Detect – De-Asserted
Pd
—
dBm
Transition: high to low
-31
—
Signal detect – Hysteresis
1.0
—
Wavelength of Operation
1260
—
Optical Return Loss
dB
1360
nm
At least 30 dB optical isolation for the
wavelength 1480 to 1580 nm
ORL
14
dB
Differential Output Voltage
VOH – VOL
0.6
2.0
V
Output LOS Voltage – Low
VOL
0
0.5
V
Output LOS Voltage – High
VOH
2.0
Vcc+0.3
V
Bit Rate
(Gb/s)
1000 BASE
Distance
(km)
Wavelength
(nm)
Package
Temp. (°C)
Tx Power
(dBm)
Rx Sens.
(dBm)
RoHS
Compliant
1.25
BX10
10
1550 DFB
SFP with
DMI
0 to 70
-9 to -3
-20
Yes
Electrical
Open collector compatible, 4.7 kΩ to
10 kΩ pull-up to Vcc (Host Supply Voltage)
ORDERING
Part number
SFP-ETH-10-RT-W15-LC
Note: Only connections with patch cords with PC or UPC connectors are supported.
www.grassvalley.com
5
SFP-ETH-10-S13-LC
1310 nm / 1.25 Gb/s Single Mode SFP Transceiver
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products..
The SFP-ETH-10-S13-LC is a single mode optical transceiver that supports
signals up to 1.25 Gb/s for bidirectional serial data communications such
as 1000BASE-LX. It is equipped with Duplex LC connectors.
KEY FEATURES
• SFP MSA compliant
• 1.25 Gb/s:
–– 1000BASE-LX compliant
• 1310 nm Multiple Quantum Well LD Transmitter
• Link distance up to 10 km at 1.25 Gb/s
• RoHS compliant
• Hot pluggable
• Diagnostic Monitoring Interface (DMI)
SPECIFICATIONS
Transmitter Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)
Parameter
Symbol
Min.
Typ.
Max.
Units
Notes
Po
-9.5
—
-3
dBm
Output power is power coupled into
a 9/125 µm single mode fiber
Optical
Optical Transmit Power
Output Center Wavelength
l
1270
1310
1350
nm
Output Spectrum Width
Δl
—
—
2.5
nm
9
—
RMS (s)
Extinction Ratio
ER
—
dB
Optical Rise Time
tr
260
ps
20% to 80% values
Optical Fall Time
tf
260
ps
20% to 80% values
RIN
-120
dB/Hz
Relative Intensity Noise
Electrical
Data Input Current – Low
IIL
Data Input Current – High
IIH
Differential Input Voltage
VIH -VIL
-350
µA
0.5
350
µA
2.4
V
Peak-to-peak
There is an internal 4.7 kΩ to 10 kΩ
pull-up resistor to VccTX
TX Disable Input Voltage – Low
VTDIS, L
0
0.5
V
TX Disable Input Voltage – High
VTDIS, H
2.0
Vcc
V
TX Disable Assert Time
TASSERT
10
µs
TX Disable De-assert Time
1
ms
TX Fault Output Voltage – Low
TDEASSERT
TFaultL
0
0.5
V
TX Fault Output Voltage – High
TFaultH
2.0
Vcc+0.3
V
-21
dBm
Open collector compatible, 4.7 kΩ
to 10 kΩ pull-up to Vcc (Host Supply
Voltage)
Receiver Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)
Optical
Sensitivity
Sens
dBm
Measured at 27-1 PRBS at BER
1E-12 @1300 nm
Maximum Input Power
Pin
-3
Signal Detect – Asserted
Pa
—
—
-21
dBm
Transition: low to high
Signal Detect – De-Asserted
Pd
—
dBm
Transition: high to low
-31
—
Signal detect – Hysteresis
1.0
—
Wavelength of Operation
1100
—
dB
1600
nm
2.0
V
Electrical
Differential Output Voltage
VOH – VOL
0.6
Output LOS Voltage – Low
VOL
0
0.5
V
Output LOS Voltage – High
VOH
2.0
Vcc+0.3
V
Open collector compatible, 4.7 kΩ
to 10 kΩ pull-up to Vcc (Host Supply
Voltage)
Bit Rate
(Gb/s)
1000
BASE
Distance
(km)
Wavelength
(nm)
Package
Temp. (°C)
Tx Power
(dBm)
Rx Sens.
(dBm)
RoHS
Compliant
1.25
LX
10
1310
SFP with DMI
-10 to 85
-9.5 to -3
-21
Yes
ORDERING
Part number
SFP-ETH-10-S13-LC
Note: Only connections with patch cords with PC or UPC connectors are supported.
www.grassvalley.com
6
SFP-ETH-RT-M85-LC
850 nm / 1.25 Gb/s Multimode SFP Transceiver
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products.
The SFP-ETH-RT-M85-LC is a multimode optical transceiver that supports
signals up to 1.25 Gb/s for bidirectional serial data communications such
as 1000BASE-SX. It is equipped with Duplex LC connectors.
KEY FEATURES
• SFP MSA Compliant
• 1.25 Gb/s:
–– 1000BASE-SX compliant
• 850 nm VCSEL Transmitter
• Link distances:
–– 300m for 62.5/125 mm multimode fiber
–– 550m for 50/125 mm multimode fiber
• RoHS-6 compliant
• Hot pluggable
• Diagnostic Monitoring Interface (DMI)
SPECIFICATIONS
Transmitter Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)
Parameter
Symbol
Min.
Typ.
Max.
Units
Notes
Po
-9
—
-3
dBm
Output power is power coupled into
a 50/125 µm multimode fiber
l
830
860
nm
Output Spectrum Width
Δl
—
—
0.85
nm
Extinction Ratio
ER
9
—
—
dB
Optical Rise Time
tr
260
ps
20% to 80% values
Optical Fall Time
tf
260
ps
20% to 80% values
RIN
-117
dB/Hz
Optical
Optical Transmit Power
Output Center Wavelength
Relative Intensity Noise
RMS (s)
Electrical
Data Input Current – Low
IIL
-350
µA
Data Input Current – High
IIH
350
µA
Differential Input Voltage
VIH - VIL
0.5
2.4
V
Peak-to-peak
VTDIS, L
0
0.5
V
TX Disable Input Voltage – High
VTDIS, H
2.0
Vcc
V
There is an internal 4.7 kΩ to 10 kΩ
pull-up resistor to VccTX
TX Disable Assert Time
TASSERT
10
µs
TX Disable Input Voltage – Low
TX Disable De-assert Time
1
ms
TX Fault Output Voltage – Low
TDEASSERT
TFaultL
0
0.5
V
TX Fault Output Voltage – High
TFaultH
2.0
Vcc+0.3
V
-17
dBm
Open collector compatible, 4.7 kΩ
to 10 kΩ pull-up to Vcc (Host Supply
Voltage)
Receiver Specifications (-10°C < Tc < 85°C, 3.1V < Vcc < 3.5V)
Optical
Sensitivity
Sens
Measured at 27-1 PRBS at
BER 1E-12
Maximum Input Power
Pin
-3
Signal Detect – Asserted
Pa
—
—
-17
dBm
dBm
Transition: low to high
Signal Detect – De-Asserted
Pd
—
dBm
Transition: high to low
-30
—
Signal Detect – Hysteresis
1.0
—
Wavelength of Operation
700
—
dB
900
nm
Electrical
Differential Output Voltage
VOH – VOL
0.6
2.0
V
Output LOS Voltage – Low
VOL
0
0.5
V
Output LOS Voltage – High
VOH
2.0
Vcc+0.3
V
Open collector compatible, 4.7 kΩ
to 10 kΩ pull-up to Vcc (Host Supply
Voltage)
ORDERING
Part number
SFP-ETH-RT-M85-LC
Bit Rate
(Gb/s)
1000
BASE
Distance (m)
Wavelength
(nm)
Package
Temp. (°C)
Tx Power
(dBm)
Rx Sens.
(dBm)
RoHS
Compliant
1.25
SX
300 / 550*
850 VCSEL
SFP with DMI
-10 to 85
-9 to -3
-17
Yes
* 300 meter for 62.5/125 mm MM fiber; 550 meter for 50/125 mm MM Fiber.
www.grassvalley.com
Note: Only connections with patch cords with PC or UPC connectors are supported.
7
SFP-ETH10G-RT-M85-LC
850 nm / 10.3 Gb/s Multimode SFP Transceiver
KEY FEATURES
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products.
The SFP-ETH10G-RT-M85-LC is a multimode optical transceiver that supports signals up to 10.5 Gb/s for bidirectional serial data communications
such as 10GBASE-SR and 10GBASE-SW. It is equipped with Duplex LC
connectors.
SPECIFICATIONS
• SFP+ MSA compliant
• 10.5 Gb/s:
–– 10GBASE-SR compliant
–– 10GBASE-SW compliant
• Link distance at 10.3 Gb/s:
–– 300m links with OM3 MMF
–– 82m links with OM2 MMF
–– 33m links with OM1 MMF
• RoHS-6 compliant
• Hot pluggable
• Diagnostic Monitoring Interface (DMI)
Specifications (0°C < Tc < 70°C, 3.14V < Vcc < 3.46V)
Parameter
Symbol
Min.
Typ.
Max.
Units
Notes
Average Launch Power
Po, Avg
-7.3
-1.0
dBm
Output power is power coupled into
a 50/125 µm multimode fiber
Optical Modulation Amplitude
Po, OMA
*
mW
* Trade-offs between center wavelength, spectral width, and minimum
OMA based on IEEE 802.3ae Table
52-8 are used
Output Center Wavelength
lc
840
860
nm
Output Spectrum Width
sl
0.45
nm
Transmitter Dispersion Penalty
TDP
3.9
dB
Relative Intensity Noise
RIN
-128
dB/Hz
12 dB reflection
Receiver Sensitivity
Sens1
-9.9
dBm
Measured with worst ER;
BER < 10-12 and PRBS 231-1
Stress Sensitivity in OMA
Sens2
180
µWp-p
ISI=3.5 dB. Measured with worst ER;
BER < 10-12 and PRBS 231-1
Transmitter Optical Specifications
850
RMS (s)
Receiver Optical Specifications
Receiver Overload
PMAX
LOS – De-asserted
LOS – Asserted
Wavelength of Operation
Optical Return Loss
—
-1
—
LOSD
—
—
-9.9
dBm
Transition: low to high
LOSA
-25
—
—
dBm
Transition: high to low
lc
840
850
860
nm
-12
dB
10.5
Gb/s
ORL
dBm
Electrical Characteristics
High-Speed Signal (CML) Interface Specification
Input Data Rate
10.3125
Differential Input Impedance
Rin
Differential Data Input Amplitude
100
150
Output Data Rate
10.3125
Differential Output Impedance
Rout
Differential Data Output Amplitude
Ω
1200
mVp-p
10.5
Gb/s
100
350
600
Internally AC coupled
Ω
700
mVp-p
Internally AC coupled
Low-Speed Signal (LVTTL) Interface Specification
Input High Voltage
2.0
Vcc+0.3
V
Input Low Voltage
GND
0.8
V
Output High Voltage
2.4
Vcc
V
Output Low Voltage
GND
0.5
V
ORDERING
Part number
SFP-ETH10G-RT-M85-LC
Bit Rate (Gb/s)
10GBASE
Distance (m)
Wavelength (nm)
Package
Temp. (°C)
RoHS Compliant
10.3
SR / SW
300 / 82 / 33*
850 VCSEL
SFP+ with DMI
0 to 70
Yes
* 300m for OM3 MMF, 82m for OM2 MMF and 33m for OM1 MMF. www.grassvalley.com
Note: Only connections with patch cords with PC or UPC connectors are supported.
8
SFP-ETH10G-RT-S13-LC
1310 nm / 10.3 Gb/s Single Mode SFP Transceiver
KEY FEATURES
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products.
The SFP-ETH10G-RT-S13-LC is a single mode optical transceiver that supports signals up to 10.5 Gb/s for bidirectional serial data communications
such as 10GBASE-LR and 10GBASE-LW. It is equipped with Duplex LC
connectors.
SPECIFICATIONS
• SFP+ MSA compliant
• 10.5 Gb/s:
–– 10GBASE-LR compliant
–– 10GBASE-LW compliant
• 1310 nm DFB LD Transmitter
• Link distance up to 10 km at 10.3 Gb/s
• RoHS-6 compliant
• Hot pluggable
• Diagnostic Monitoring Interface (DMI)
Specifications (0°C < Tc < 70°C, 3.13V < Vcc < 3.47V)
Parameter
Symbol
Min.
Average Launch Power
Po, Avg
-8
Optical Modulation Amplitude
Po, OMA
-5.2
Δl
1270
Typ.
Max.
Units
Notes
0.5
dBm
Output power is power coupled into a
9/125 µm single mode fiber
Transmitter Optical Specifications
Output Center Wavelength
Output Spectrum Width
dBm
1310
sl
Side Mode Suppression Ratio
SMSR
30
Extinction Ratio
ER
3.5
Relative Intensity Noise
RIN
1355
nm
1
nm
-20 dB width
dB
Average launch Power of OFF
Transmitter
-128
dB/Hz
-30
dBm
Receiver Optical Specifications
Receiver Sensitivity
Sens1
-14.4
dBm
Measured with worst ER; BER < 10-12
and PRBS 231-1 at 10.3125 Gb/s average received power
Sensitivity in OMA
Sens1
-12.6
dBm
Measured with worst ER; BER < 10-12
and PRBS 231-1 at 10.3125 Gb/s
Stress Sensitivity in OMA
Sens2
-10.3
dBm
Per IEEE 802.3ae. Equivalent to -13.3 dBm
average power at Infinite ER
—
Receiver Overload
PMAX
LOS – De-asserted
LOSD
LOS – Asserted
LOSA
-28
lc
1260
Wavelength of Operation
Optical Return Loss
0.5
—
dBm
-16
—
ORL
dBm
Transition: low to high
dBm
Transition: high to low
1565
nm
-12
dB
10.5
Gb/s
Electrical Characteristics
High-Speed Signal (CML) Interface Specification
Input Data Rate
10.3125
Differential Input Impedance
Rin
100
Differential Data Input Amplitude
150
Output Data Rate
10.3125
Differential Output Impedance
Rout
Ω
1200
mVp-p
10.5
Gb/s
100
Differential Data Output Amplitude
400
600
Internally AC coupled
Ω
700
mVp-p
Internally AC coupled
Low-Speed Signal (LVTTL) Interface Specification
Input High Voltage
2.0
Vcc+0.3
V
Input Low Voltage
GND
0.8
V
Output High Voltage
2.4
Vcc
V
Output Low Voltage
GND
0.5
V
ORDERING
Part number
SFP-ETH10G-RT-S13-LC
Type
Bit Rate
(Gb/s)
10GBASE
Distance (km)
Wavelength
(nm)
Package
Temp. (°C)
RoHS
Compliant
1-TX+ 1-RX
10.3
LR / LW
10
1310 DFB
SFP+ with DMI
0 to 70
Yes
Note: Only connections with patch cords with PC or UPC connectors are supported.
www.grassvalley.com
9
SFP-ETH10G-RT-CXX-LC
CWDM / 10.3 Gb/s Single Mode SFP Transceiver
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products.
The SFP-ETH10G-RT-CXX-LC is a single mode optical transceiver that
supports signals up to 10.5 Gb/s for bidirectional serial data communications such as 10GBASE-LR. It is equipped with Duplex LC connectors.
KEY FEATURES
• SFP+ MSA compliant
• 10.5 Gb/s:
–– 10GBASE-LR compliant
• Uncooled 18-wavelength CWDM DFB laser transmitter
• RoHS-6 compliant
• Hot pluggable
• 11 dB minimum power budget
• Diagnostic Monitoring Interface (DMI)
SPECIFICATIONS
Specifications (0°C < Tc < 70°C, 3.13V < Vcc < 3.47V)
Parameter
Symbol
Min.
Typ.
Max.
Units
Notes
Po, AVG
-3
—
1
dBm
Output power is power coupled into
a 9/125 µm single mode fiber
l
lc - 6.5
lc
lc + 6.5
nm
ITU-T G.694.2 CWDM wavelength
from 1271 nm to 1611 nm, each step
20 nm
1
nm
-20 dB width
Transmitter Optical Specifications
Average Launch Power
Output Center Wavelength
Output Spectrum Width
Side Mode Suppression Ratio
Relative Intensity Noise
Δl
—
SMSR
30
dB
RIN
Average Launch Power of OFF
transmitter
-128
dB/Hz
-30
dBm
-14.4
dBm
Receiver Optical Specifications
Sensitivity
Receiver Overload
PMAX
LOS – De-Asserted
LOSD
—
—
-16
dBm
Transition: low to high
LOS – Asserted
LOSA
-28
—
—
dBm
Transition: high to low
lc
1260
—
1620
nm
Wavelength of Operation
0.5
Measured with average power;
BER < 10-12 and PRBS 231-1
dBm
Electrical Characteristics
High-Speed Signal (CML) Interface Specification
Input Data Rate
10.3125
TX Clock Tolerance
Differential Input Impedance
±100
Rin
Differential Data Input Amplitude
100
150
Output Data Rate
Rout
Differential Data Output Amplitude
1200
600
Clock tolerance for 9.95 Gb/s,
10.3125 Gb/s and 10.5187 Gb/s
mVp-p
Internally AC coupled
Gb/s
±100
ppm
700
mVp-p
100
350
ppm
Ω
10.3125
RX Clock Tolerance
Differential Output Impedance
Gb/s
Clock tolerance for 9.95 Gb/s,
10.3125 Gb/s and 10.5187 Gb/s
Ω
Internally AC coupled
Low-Speed Signal (LVTTL) Interface Specification
Input High Voltage
2.0
Vcc+0.3
V
Input Low Voltage
GND
0.8
V
Output High Voltage
2.4
Vcc
V
Output Low Voltage
GND
0.5
V
www.grassvalley.com
10
SFP-ETH10G-RT-CXX-LC
ORDERING
Part number
Bit Rate (Gb/s)
10GBASE
Wavelength (nm)
Package
Temp. (°C)
RoHS Compliant
10.3
LR
CWDM*
SFP+ with DMI
0 to 70
Yes
SFP-ETH10G-RT-CXX-LC
*CWDM: 18 Wavelengths from 1271 nm to 1611 nm, each step 20 nm (0 to 70°C).
Central Wavelength (nm)
Central Wavelength (nm)
Value for
-CXX
Min.
Typ.
Max.
Clasp Color Code
Value for
-CXX
Min.
Typ.
Max.
Clasp Color Code
-C27
1264.5
1271
1277.5
Light Purple
-C45
1444.5
1451
1457.5
Yellow Orange
-C29
1284.5
1291
1297.5
Sky Blue
-C47
1464.5
1471
1477.5
Gray
-C31
1304.5
1311
1317.5
Yellow Green
-C49
1484.5
1491
1497.5
Violet
-C33
1324.5
1331
1337.5
Yellow Ocher
-C51
1504.5
1511
1517.5
Blue
-C35
1344.5
1351
1357.5
Pink
-C53
1524.5
1531
1537.5
Green
-C37
1364.5
1371
1377.5
Beige
-C55
1544.5
1551
1557.5
Yellow
-C39
1384.5
1391
1397.5
White
-C57
1564.5
1571
1577.5
Orange
-C41
1404.5
1411
1417.5
Silver
-C59
1584.5
1591
1597.5
Red
-C43
1424.5
1431
1437.5
Black
-C61
1604.5
1611
1617.5
Brown
Note: Only connections with patch cords with PC or UPC connectors are supported.
CWDM units are only available on special request. Lead time is usually 6 to 8 weeks ARO.
www.grassvalley.com
11
SFP-ETH10G-RT-W27-LC
1-Fiber WDM / 10.3 Gb/s Single Mode SFP Transceiver
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products.
The SFP-ETH10G-RT-W27-LC is a single mode optical transceiver that
supports signals up to 10.5 Gb/s for bidirectional serial data communications over a single fiber. It is equipped with Simplex LC connectors.
KEY FEATURES
•
•
•
•
•
•
•
•
SPECIFICATIONS
1-fiber bidirectional transceiver
SFP+ MSA compliant
10GBASE-BX compliant
10.5 Gb/s:
–– 1270 nm multiple quantum well LD transmitter
RoHS-6 compliant
Hot pluggable
Link distance up to 10 km at 10.3 Gb/s
Diagnostic Monitoring Interface (DMI)
Specifications (0°C < Tc < 70°C, 3.13V < Vcc < 3.47V)
Parameter
Symbol
Min.
Typ.
Max.
Units
Notes
Po, AVG
-5
—
0
dBm
Output power is power coupled into
a 9/125 µm single mode fiber
Output Center Wavelength
lc
1260
1270
1280
nm
Output Spectrum Width
σl
1
nm
-128
dB/Hz
-30
dBm
-14
dBm
Transmitter Optical Specifications
Average Launch Power
Side Mode Suppression Ratio
SMSR
Relative Intensity Noise
30
-20 dB width
dB
RIN
Average Launch Power of OFF
transmitter
Receiver Optical Specifications
Sensitivity at 10.3 Gb/s
Receiver Overload
PMAX
0.5
—
LOS – De-Asserted
LOSD
—
—
LOS – Asserted
LOSA
-26
—
lc
1320
Wavelength of Operation
Measured with average power;
BER < 10-12 and PRBS 231-1
dBm
-16
dBm
Transition: low to high
—
dBm
Transition: high to low
1340
nm
At least 30 dB optical isolation for
the wavelength 1260 to 1280 nm
Electrical Characteristics
High-Speed Signal (CML) Interface Specification
Input Data Rate
Differential Input Impedance
Rin
Differential Data Input Amplitude
10.3125
Gb/s
100
Ω
150
Output Data Rate
Differential Output Impedance
Rout
Differential Data Output Amplitude
350
1000
mVp-p
10.3125
Gb/s
100
Ω
600
700
mVp-p
Vcc+0.3
V
Internally AC coupled
Internally AC coupled
Low-Speed Signal (LVTTL) Interface Specification
Input High Voltage
2.0
Input Low Voltage
GND
0.8
V
Output High Voltage
2.4
Vcc
V
Output Low Voltage
GND
0.5
V
ORDERING
Part number
SFP-ETH10G-RT-W27-LC
Bit Rate
(Gb/s)
Distance
(km)
TX (nm)
RX (nm)
Package
Temp. (°C)
RoHS Compliant
10.3
10
1270 DFB
1330
SFP+ with DMI
0 to 70
Yes
Note: Only connections with patch cords with PC or UPC connectors are supported.
WDM units are only available on special request. Lead time is usually 6 to 8 weeks ARO.
www.grassvalley.com
12
SFP-ETH10G-RT-W33-LC
1-Fiber WDM / 10.3 Gb/s Single Mode SFP Transceiver
Small form-factor pluggable (SFP) optical module cartridge for Densité
frames and Grass Valley/Telecast standalone fiber products.
The SFP-ETH10G-RT-W27-LC is a single mode optical transceiver that
supports signals up to 10.5 Gb/s for bidirectional serial data communications over a single fiber. It is equipped with Simplex LC connectors.
KEY FEATURES
•
•
•
•
•
•
•
•
1-fiber bidirectional transceiver
SFP+ MSA compliant
10GBASE-BX compliant
10.5 Gb/s:
–– 1330 nm multiple quantum well LD transmitter
RoHS-6 compliant
Hot pluggable
Link distance up to 10 km at 10.3 Gb/s
Diagnostic Monitoring Interface (DMI)
SPECIFICATIONS
Specifications (0°C < Tc < 70°C, 3.13V < Vcc < 3.47V)
Parameter
Symbol
Min.
Typ.
Max.
Units
Notes
Po, AVG
-5
—
0
dBm
Output power is power coupled into
a 9/125 µm single mode fiber
Output Center Wavelength
lc
1320
1330
1340
nm
Output Spectrum Width
σl
1
nm
Transmitter Optical Specifications
Average Launch Power
Side Mode Suppression Ratio
SMSR
Relative Intensity Noise
30
-20 dB width
dB
RIN
Average Launch Power of OFF
transmitter
-128
dB/Hz
-30
dBm
-14
dBm
Receiver Optical Specifications
Sensitivity at 10.3 Gb/s
Measured with average power;
BER < 10-12 and PRBS 231-1
Receiver Overload
PMAX
0.5
—
LOS – De-Asserted
LOSD
—
—
-16
dBm
Transition: low to high
LOS – Asserted
LOSA
-26
—
—
dBm
Transition: high to low
lc
1260
1280
nm
At least 30 dB optical isolation for
the wavelength 1320 to 1340 nm
Wavelength of Operation
dBm
Electrical Characteristics
High-Speed Signal (CML) Interface Specification
Input Data Rate
Differential Input Impedance
Rin
Differential Data Input Amplitude
10.3125
Gb/s
100
Ω
150
Output Data Rate
Differential Output Impedance
Rout
Differential Data Output Amplitude
350
1000
mVp-p
10.3125
Gb/s
100
Ω
600
700
mVp-p
Internally AC coupled
Internally AC coupled
Low-Speed Signal (LVTTL) Interface Specification
Input High Voltage
2.0
Vcc+0.3
V
Input Low Voltage
GND
0.8
V
Output High Voltage
2.4
Vcc
V
Output Low Voltage
GND
0.5
V
ORDERING
Part number
SFP-ETH10G-RT-W33-LC
Bit Rate
(Gb/s)
Distance
(km)
TX (nm)
RX (nm)
Package
Temp. (°C)
RoHS Compliant
10.3
10
1330 DFB
1270
SFP+ with DMI
0 to 70
Yes
Note: Only connections with patch cords with PC or UPC connectors are supported.
WDM units are only available on special request. Lead time is usually 6 to 8 weeks ARO.
www.grassvalley.com
13
Small Form-factor Pluggable (SFP) Optical Module Cartridges (Ethernet)
Global Services
In a world of ever-increasing complexity and system distribution,
broadcast producers inside a studio or outside in a vehicle need production control equipment suppliers who can provide industry-leading
technical support. Personnel is but one part of the support equation. The other is a business infrastructure capable of deploying and
cost-effectively supporting reliable solutions. Grass Valley Global Services has the depth of knowledge, industry experience and technical
expertise to achieve this objective. The Global Services portfolio provides everything necessary insure maximum uptime and high velocity
problem resolution.
Grass Valley Global Services delivers a comprehensive array of tangible
value:
• A global network of field engineers with the experience, knowledge and skill
to keep production switchers/vision mixers and associated equipment up to
date, operational and optimized
• A worldwide parts distribution system that ensures rapid access to replacement parts
• A team of educators skilled in the nuances of production control and switcher
operations
• Technical and operational training, provided on-site at Grass Valley facilities
worldwide and online, that maximizes productivity through tailored learning
paths
• Comprehensive support agreements that ensure every Grass Valley system
remains in peak condition — all while supporting the enterprise’s need for
financial predictability
Grass Valley Global Services offerings deliver tangible value. The Global
Services organization does this by providing the resources to ensure that
users get the maximum value from an investment in Grass Valley production switchers — from initial startup through the entire in-service lifespan.
Global Services empowers users to meet tactical day-to-day objectives
while giving staff more time to focus on strategic business initiatives. A
global presence, logistics expertise and world-renowned team of media
professionals are here to help the achievement of financial performance
objectives by reducing risk while boosting operational efficiencies.
GLOBAL SERVICES PROVIDES:
• Unequalled depth of industry knowledge and technical expertise
• Over 50 years of worldwide experience
• Complete set of services:
–– Strategic advice
–– System architecture
–– Workflow analysis and design
–– Project management
–– Integration and implementation
–– Performance optimization
–– Technical and operational training
–– Educational services
• Address today’s challenges and prepare for tomorrow’s opportunities
GVB-1-0643B-EN-DS
WWW.GRASSVALLEY.COM
Join the Conversation at GrassValleyLive on Facebook, Twitter, YouTube
and Grass Valley - A Belden Brand on LinkedIn.
www.grassvalley.com/blog
Belden, Belden Sending All The Right Signals, and the Belden logo are trademarks or registered trademarks of Belden Inc.
or its affiliated companies in the United States and other jurisdictions. Grass Valley products listed above are trademarks or
registered trademarks of Belden Inc., GVBB Holdings S.A.R.L. or Grass Valley Canada. Belden Inc., GVBB Holdings S.A.R.L.,
Grass Valley Canada and other parties may also have trademark rights in other terms used herein.
Copyright © 2017 Grass Valley Canada. All rights reserved. Specifications subject to change without notice.
14