70 F-16说明书-Q.cdr

-
FIGHTING
FALCON
USER MANUAL
Wingspan:B7Bmm
lten No.: FJ211
Version No.: FJ211-V01
1- 12
13-24
www.sz-flieewi
Introduction
EN
The F-16C "Fighting Falcon" was originally developed for the United States Air Force (USAF)
as an air superiority day fighter, but it eventually evolved into a successful all-weather multirole aircraft. The F-16C features an internal M61 Vulcan cannon and multiple locations for
mounting weapons and other mission-specific equipment. Operating in nearly 30 countries to
this day, the F-16 has distinguished its place in aviation history.
Freewing has modeled this brilliant EPO foam aircraft around a 70mm electric ducted fan
(EDF) powerplant. With a 1306mm length and 878mm wingspan, this 1/12 scale flying replica
includes many exciting features! An accurate scale outline with sharp surface details and panel
lines will make this model stand out at your airfield. Removable main wings and a magnetic
nose cone make transport very convenient. The cockpit battery bay cover is secured with a
sliding latch to prevent separation during flight, and the entire aircraft is reinforced with
strategic placement of carbon fiber tubes to withstand vigorous flying maneuvers.
Our Freewing 70mm F-16C V2 model jet uses electric retractable landing gear for lower drag
and better scale appearance during flight. The model is offered in three different powerplant
options: 4s Standard, 6s Upgrade, and 6s Professional. These powerplants achieve a maximum
flying speed of 125kph, 140kph, and 165kph, respectively. The aircraft is designed for stability,
strong climbing performance, and short takeoff distance, suitable for all levels of jet pilots. The
aircraft can also maintain a high alpha of 30 degrees to demonstrate its superior low speed
stability.
We feature this exciting aircraft in the modern three tone gray US Air Force base colors as
well as an Artic Camo paint scheme, and three decal sets are included for you to choose from to
customize your model from various actual Air Force squadrons.
&
NOTE: This is not a toy. Not for children under 14 years. Young people under the age of 14 should only be permitted to operate
this model under the instruction and supervision of an adult. Please keep these instructions for further reference after completing
model assembly.
Note:
1.
This is not a toy! Operators should have some basic experience. Beginners should operate only under the
guidance of a professional instructor.
2. Before beginning assembly, please read through the instructions and carefully follow them throughout the build.
3. Freewing and it's vendors will not be held responsible for any losses due to improper assembly and operation.
4. Model airplane operators must be at least 14 years of age.
5. This airplane is made of EPO foam material, covered with surface spray paint. Don't use chemicals to clean as it
may cause damage.
6. You should avoid flying in areas such as public places, areas with high voltage power lines, nearby highways,
airports or in other areas where laws and regulations clearly prohibit flight.
7. Do not fly in bad weather conditions, including thunderstorms, snow, etc...
8. Lipo batteries should be properly stored in a fire proof container and be kept at a minimum of 2M distance away
from flammable or explosive materials.
9. Damaged or scrap batteries must be properly discharged before disposal or recycling to avoid spontaneous
combustion and fire.
10. At the Flying Field, properly dispose of any waste you have created, don't leave or burn your waste.. Ensure that
your throttle is in the low position and that your radio is turned on before connecting the Lipo battery.
11.Ensure that the throttle is in the lowest position and transmitter switch on, before connecting a Lipo Battery to the
ESC of the aircraft.
12.
Do not try to catch the airplane while in flight or during landing. Wait for the airplane to come to a complete stop
before handling.
13.
Index
Introduction
Product basic parameters
Parts List
PNP Assembly Instructions
Servo Installation Instructions
Landing ear Installation Instructions
Servo parameters
C-wr&g·
1
2
2
3
5
6
7
Control board Instruction
8
Motor parameters
8
Powersystem installation Instructions 9
Battery Installation
10
Center of Gravity
10
11
Control surface diagram
12
Dual rates
F-16 Fighting Falcon
!ten No.: FJ211
Version No.: FJ211-V01
...
Product basic parameters
Standard version
Wing loading: 121g/dm2
Motor: 2849-2850KV(4S)
brushless outrunner motor
Ducted fan: 70mm 12-blade ducted fan
Flight speed: 125km/h
ESC: 60A brushless ESC
Servo: 9g digit plastic servo(6pcs)
Weight: 1400g (without battery)
Thrust: 1500g
-.
C:
.
.....
-E
Lt)
"'1:1'
C")
Upgrade version
Wing loading:145g/dm 2
Motor: 3048-2150KV(6S)
brushless outrunner motor
Ducted fan: 70mm 12-blade ducted fan
Flight speed: 140km/h
ESC: 60A brushless ESC
Servo: 9g digit metal gear servo (6pcs)
Weight: 1450g (without battery)
Weight: 2150g (without battery)
E
co
.....
co
1
Professional version
1306mm(51.4in.)
Wing loading:145g/dm 2
Motor: 3048-2300KV(6S)
Note: The parameters stated here are derived from test results using our accessories.
brushless outrunner motor
If you use other accessories, the test results will differ. We cannot provide technical support if you
Ducted fan: 70mm 12-blade ducted fan
have a problem when using other accessories.
ESC: BOA brushless ESC
Servo: 9g digit metal gear servo(6pcs)
The kit doesn't include the optional missiles and pylons, if you wish to have them, please contact your Flight speed: 165km/h
local dealer.
Weight: 1450g (without battery)
Weight: 2400g (without battery)
&
Parts List
Different types of kits will come with certain specific parts. Refer to the list of parts for your type of kit in the chart below.
NO.
Parts Name
1
Fuselage
2
Main wing
3
Vertical tail
4
Horizontal tail
5
Nose cone, Fin
F-16 Fighting Falcon
lten No.: FJ211
Version No.. FJ211 V01
PNP
r;:t��i:�1cf�:r�6s
Pre-installed all
electronic parts
Pre-Installed all
electronic parts
v
v
KIT Plus Airframe
Pre-installed No electronic
equipment
servo
Pre-installed No electronic
equipment
servo
Pre-installed No electronic
equipment
servo
v
v
v
v
NO.
Parts Name
PNP
6
Missiles and pylons
Optional part,
purchase seperately
7
Pushrod
8
Carbon Fiber tube
9
Glue/Decals
10
Manual
v
v
v
v
KIT Plus
Airframe
Optional part,
Optional part,
purchase seperately purchase seperately
v
v
v
v
r-wtng·
v
v
v
v
•
PNP Assembly Instructions
EN
Main wing assembly
1.lnsert the carbon
Carbon tube ( 06x5OOmm)
�
Screw ( PWA3x8 4pcs )
0
.>.
�
'
I
�
---
1
r-I----,-
"'·�-
; "'-
�
L
,_./
1�
StepQ
Horizontal Stabilizer Assembly
Referring to the photo:
1.Use the provided glue to attach
the horizontal stabilizer to the
tail of the fuselage.
2.Use glue to attach the carbon
rod into the trough for
additional strength.
3.Repeat the above steps for the
other side.
A-Tail fuselage
8-Horizontal tail
C-Carbon piece
Note:Please use the
provided EPO glue. For best
results, glue should be spread
evenly, then wait for 90
seconds before assembly
•
-F-16 Fighting Falcon
!ten No.: FJ211
Version No.: FJ211-V01
PNP Assembly Instructions
EN
Vertical Stabilizer Assembly
1.Feed the rudder servo cable into the trough.
2.Use glue to attach the vertical tail.
A-Vertical tail
B-Trough
C-Servo cable
A
Missile and Pylon Installation
(Note: This kits does not come with missiles and pylons. Contact your local dealer to
purchase them.
A-AIM-9 Missile
8-Carbon tube
C-Screw driver
Step@
Step0
\
___-AIM-120 Missile
Step@)
F-16 Fighting Falcon
lten No.: FJ211
Version No.: FJ211-V01
Introduction to Servo Installation
EN
Main wing servo Installation A- 9g servo
1.Use a servo tester or radio to
center the servo arm.
2.Use glue to install the servo and
aileron horn to the main wing.
3.Feed the servo cable through
the trough, after the servo is
installed, apply the decal.
4. Insert one end of the pushrod
to the servo arm and adjust its
length. Then snap the clevis to
the aileron horn.
5.Repeat the above four steps for
the other wing.
Elevator servo Installation
1.Use a servo tester or radio to
center the servo arm.
2.Use glue to install the servo and
control horn to the elevator.
3.Feed the servo cable through
the trough.
4.Inset one end of the pushrod
to the servo arm and adjust its
length. Then snap the clevis to
the elevator control horn.
5.Repeat the above four steps for
the other elevator
Rudder servo Installation
1.Use a servo tester or radio to
center the servo arm.
2.Use glue to intall the servo and
servo arm to the rudder.
3.Feed the servo cable through
the trough.
4.Insert one end of the pushrod
to the servo arm and adjust its
length. Then snap the clevis to
the rudder control horn.
B - Main wing pushrod
C -Aileron horn
D - Main wing servo trough
D--------,
\
A- 9g servo
B - Elevator horn
C - Elevator pushrod
A- 9g servo
B - Rudder horn
C -Rudder pushrod
+--- 55mm ---+I
Pushrod diameter 01.2mm
(2-1/5")
�·· · ·0·��
3 ··· ··· ·· ·O
0
�n��:
'-'========- �
� ·-·:_ ·_·_·····.-.
3
-
Elevator pushrod mounting hole
Elevator pushrod size
'll�=======IWM�
C
Aileron pushrod mounting hole
Aileron pushrod size
'l]�=======IW-�
A·-._
Pushrod diameter 01.5mm
----- 168mm ---+I
(6-3/4")
Rudder pushrod mounting hole
Rudder pushrod size
°11...::::=====••
-----,1
----- 55mm
(2-1/5')
Pushrod diameter 01.2mm
1· ········m0�
� • .• •.• . :
0
�n��_· ,·-····
71---========::::i-- � �· ·.
1
······.·.·.
J
F-16 Fighting Falcon
!ten No.: FJ211
Version No.: FJ211-VO1
Landing gear Installation Instructions
EN
Nose landing gear Assembly
Please refer to the following diagram to assemble, replace or revise the nose landing gear.
sparepart name and parameters
A- Grub screws (M3x3 1pcs)
B- Wheel lock
C- Wheel
D- Nose gear main strut
E- Steering arm tiller
F- Grub screw (M3x3)
G- Nose gear steering ring
H- Nose gear steering rod
I - Metal trunion
J -C clip (02.0mm 1pc)
K- Servo plastic cover(left)
L - Servo plastic cover(right)
M- Screw (PA1.7x8 2pcs)
M1 - Screw (PB1.0x10 3pcs)
N-Screw (KA2.6x12 4pcs)
0- Nose gear metal reinforcement plate.
P -Assembled Nose gear
Q-Servo
R-Screw (PWA2.0x8 2pcs)
S-Steering pushrod
T- Nose gear cover
J·---
Step@
StepQ
\
Step@)
Step8
\
\
StepG,
Nose steering pushrod size
I----- 65mm --+-I
(2-9/16")
Step(i)
Servo pushrod installing hole
Pushrod diameter: 01.2mm
�O
�
i=--...,,,;
S.'E':SLJaaa;aaa;acaael
�gp'
-;::·=·=o
�
� Note: Ensure that the flat side of the gear shaft is facing towards the screw hole before tightening the grub screw in order to ensure that
the gear is both anchored and facing in the proper direction. Failure to do so may result in the the gear coming loose and falling off.
F-16 Fighting Falcon
lten No.: FJ211
Version No.: FJ211-V01
Landing gear Installation Instructions
Main landing gear Installation
EN
Step@)
Please assemb le and disassemble the main landing gear with
reference to the following photo and diagrams.
A-Grub screw (M3x3 1pc).
B-Wheel lock.
C-Wheel.
D-Rear gear main strut.
E-Electric landing gear retract.
F-Grub screw (M3x3 2pcs).
G-Assembled Main Landing
Gear.
H-Metal reinforcement plate.
I -Screw (KA2.6x12 8pcs)
J -Main Gear cover.
'\_/
:tj)
StepC,
J
C
D
�E
Step8
Step@
Servo parameters
A servo or reversed servo is defined as follows:
When the servo input signal changes from 1000ųs to
2000ųs, if the servo arm rotates clockwise, it's a
positive servo. If it rotates counter clockwise, it's a
reversed servo.
.....-
If you choose to purchase a different brand of servo, please refer to
the following 11st to ensure it is the correct size .
Servo position Servo regulation No. Standard/Reverse Servo cable length
Nose steering
9g Digit-Plastic
Left aileron
Right aileron
Standard
100mm
9g Digit-Plastic
1
2
Standard
200mm
9g Digit-Plastic
3
Standard
200mm
Left elevator
9g Digit-Plastic
Standard
850mm
Right aileron
9g Digit-Plastic
4
5
Reverse
850mm
Rudder
9g Digit-Plastic
6
Standard
900mm
F-16 Fighting Falcon
lten No.: FJ211
Version No.: FJ211-V01
Control board instruction
EN
Strobe Ii ht
Landin Gear
Rudder/Nose steering
Elevator
Aileron
Fla
(power to the receiver)
Connect all the control surfaces listed on
the control board to the control board. All
others will be connected directly to the
receiver.
Land in
Rudder
Elevator
Aileron
Motor parameters
0
0
N
N
LO
CY)
N
0
16.7
11.4
3048-21 S0KV
3048-2300KV
53.9
\S1
I\.)
0)
3
3
Unit: mm
0
\S1
.I>,
3-+-�-------j
3+--�---1
LO
CY)
N
0
38.6
Item No.
EDF Fans
Voltage
(V)
Current
Power
(W)
Thrust
(Kg)
(A)
2849-2850KV
Unit: mm
Efficiency
Motor
Specifications
(g/w)
Rotating speed
(rpm)
Weight
(g)
E7215
70mm
12-blade EDF
14.8
55-60
880
1.5-1.6
1.76
2849-2850
42000
146
E7216
70mm
12-blade EDF
22.2
55-60
1330
2.05-2.25
1.65
3048-2150
47700
180.7
E7217
70mm
12-blade EDF
22.2
65-72
1510
2.3-2.5
1.6
3048-2300
51000
180.7
F-16 Fighting Falcon
lten No.: FJ211
Version No.: FJ211-V01
Power system instructions
EN
Standard version
A- 2849-2850KV Brushless
outrunner motor
B- 70mm Outrunner ducted frame
C-Screw (PWM3x6 4pcs)
D- Motor chuck
E- Motor chuck fixed plate
F - 70mm 12-blade ducted fan
G-Spacer
H-Nut
I -Spinner
J -Screw (M3x8 1pc)
F
i.
J
H
E
G
Upgrade version
,
I
I
!
.
F
A- 3048-21S0KV Brushless
outrunner motor
B- 70mm Outrunner ducted frame
C-Screw (PWM3x6 4pcs)
D- Motor chuck
E- Motor chuck fixed plate
F - 70mm 12-blade ducted fan
G-Spacer
H-Nut
I -Spinner
J -Screw (M3x8 1pc)
\
E
Professional version
A- 3048-2300KV Brushless
outrunner motor
B- 70mm Outrunner ducted frame
C-Screw (PWM3x6 4pcs)
D- Motor chuck
E- Motor chuck fixed plate
F - 70mm 12-blade ducted fan
G-Spacer
H-Nut
I -Spinner
J -Screw (M3x8 1pc)
F
\
E
J
& When the ESC is connected to the battery, to not touch the ESC or motor to avoid serious injury.
When testing the EDF, use a test stand for safety.
Refer to the following diagram to
install the ESC and power system:
A-Sc rews (PA3x25 2pcs)
B-ESC fixed wood piece 1
C-ESC
D-ESC fixed wood piece 2
E-1 ntake grid
F -Sc rews (PWA3x8 4pcs)
G- 70mm EDF power system
H- Sc rews (KA2.6x8 3pcs)
I -EDF cover
J -Sc rews (KA2.6x8 4pcs)
K-Fin
Step@
F-16 Fighting Falcon
!ten No.: FJ211
Version No.: FJ211-V01
Battery Installation
C
Install the battery and use velcro to secure it.
battery tray
=45(mm)
The battery capacity and discharge rate
we advise to use are as follows:
45 14.8V 2600-4000mAh
65 22.2V 2600-4000mAh
discharge rate� 30C
Before connectting the battery to the ESC, please
switch on the transmitter and make sure the
throttle is in the lowest position. Use a the kill
switch if you have one assigned.
Center of Gravity
The correct center of gravity is directly related to the success of the flight, please refer to the following CG
diagram to adjust your plane's center of gravity.
- You can move the battery forward or backward
to adjust the center of gravity.
- If you can not adjust the CG by moving the
battery, you can also use some other suitable
material such as sticky backed weight to
counterweight. It's highly important to make
sure that CG is in the correct position,
especially for the first few flights.
- Afterwards, you can adjust it to suit your
individual taste.
90mm
(3-1 /2")
F-16 Fighting Falcon
lten No.: FJ211
Version No.: FJ211-V01
Control direction test
EN
After the airplane is completely assembled but before the first flight, turn on your radio and ensure that the
throttle is in the lowest position, engage the kill switch if you have one assigned. Connect a fully charged battery
to the ESC, then use your radio to test and ensure that every control surface is moving in the correct direction.
Aileron
Stick Left
Stick Right
Elevator
Stick Back
•!!!!!!!!
!!!!!!!!
!!!!!!!!
•-
-•
•-
-
iiiiiiii
Stick Forward
....
Rudder
Stick Left
Stick Right
�Ill
Ill�
...
F-16 Fighting Falcon
!ten No.: FJ211
Version No.: FJ211-V01
Dual Rates
EN
According to our test results, the following rates proved to be a good starting point. Low rates are good for initial
flights or less experienced pilots. High Rates will be more sensitive to control inputs After intial flights, adjust the
rates to suit your own style.
2
H
H
_____l_ 1
Note: carefully check to see if there are any movements
from the other control surfaces when you move your control
sticks, say, the ailerons move when you pull up elevator. If
so, you can adjust the expo until only the control surface
you engage moves.
Aileron
Elevator
Rudder
Low Rates
H1/H2 22mm/22mm
D/R Rate: 65%
H1/H2 19mm/19mm
D/R Rate: 80%
H1/H2 30mm/30mm
D/R Rate: 85%
High Rates
H1/H2 34mm/34mm
D/R Rate: 100%
H1/H2 23mm/23mm
D/R Rate: 100%
H1/H2 35mm/35mm
D/R Rate: 100%
F-16 Fighting Falcon
lten No.: FJ211
Version No.: FJ211-V01
Dongguan Freewing Electronic Technology Ltd
HK Freewing Model International Limited
Add.:FeiYi Building,face to Labor Bureau, Fumin Middle Road, Dalang Town,
Dongguan City , Guangdong Province, China
Web: http://www.sz-freewing.com
Email:freewing@sz-freewing.com
Tel: 86-769-82669669
Fax:86-769-82033233
*�mt w � -=r-*31-t� � �& 0 �
� � t Htl� IE �j� �& 0 �
:1:-fu:l:Jl:: '*�*%m1:M�'M � q:r n402-408% lSJ!� !J]�
Web: http://www.sz-freewing.com
Email:freewing@sz-freewing.com
Tel: 86-769-82669669
Fax:86-769-82033233
Download PDF
Similar pages