High Security Heavy Duty Shredders VZ 14.00

High Security
Heavy Duty Shredders
VZ 14.00
Perfect shredding and high performance
in DIN security levels 4 and 5
Documentation High Security Heavy Duty Shredders VZ 14.00 / Page 1of 5
Technical changes and colour variances reserved; issue 02/2012
MARTIN YALE International GmbH, D-88677 Markdorf • Tel. +49(0)75 44 / 60-0 • vertrieb@martinyale.de • www.intimus.com
High Security Heavy Duty Shredders
VZ 14.00
Perfect shredding and high performance.
The large high security shredders VZ 14.00/4 and VZ 14.00/5 have proven
themselves for over 10 years for the destruction of large quantities of data with
high and maximum security requirements. The machine is easily loaded via the
generously sized loading table with integrated conveyor belt.
Pre-shredding
The shredded material from the primary shredder – 6 x 50 mm particles –
falls onto a conveyor belt and is transported directly to the cutting shafts
of the security shredder.
Only the combination of primary and security shredder enables such a large
throughput at high security levels.
Execution VZ 14.00/4:
2 x 15 mm Security Shredder
The 2 x 15 mm cutter guarantees security level 4 as per DIN 32757-1.
Thanks to the subsequent compaction of the fine
particles in the integrated bale press, even
the requirements for security level 5 are met.
Execution VZ 14.00/5:
2 x 4.5 mm Security Shredder
The security shredder with 2 x 4.5 mm particle
size enables compliance with security level 5
as per DIN 32757-1. Thanks to the subsequent compaction
of the particles, the requirements of security level 5 are even exceeded.
Documentation High Security Heavy Duty Shredders VZ 14.00 / Page 2 of 5
Technical changes and colour variances reserved; issue 02/2012
MARTIN YALE International GmbH, D-88677 Markdorf • Tel. +49(0)75 44 / 60-0 • vertrieb@martinyale.de • www.intimus.com
High Security Heavy Duty Shredders
VZ 14.00
Efficient, thermally protected gear motors
(4.0 + 3.3 kW motor output) and robust drive
Optimum cutting performance thanks to robust,
low-wear blade shafts made of galvanised special steel
Working width: 500 mm;
suitable for the most common EDP formats
Professional solution
■ Automatic control of primary and security shredder
■ Parallel operation of shredder and press
■ Electronic fill level monitoring of the press chamber
■ Automatic triggering of the press cycle
■ Shredder can still be loaded during this process
Visual signal of the message „Bale ready“ and
simultaneous interruption of the cutting process
■ Integrated automatic oiler for the security shredder
■
Optimum handling
■ Push-button bale ejection
■ Compact bales
■ Ejection into collection bag for low-dust, clean transport
as well as packaging protected from the elements
Standard safety equipment
■ Wide EMERGENCY-STOP bar on feed table for immediate
machine stop in the event of danger
■ Lockable master switch and key-operated switch
■ Safety switch on the service door of the security shredder
for machine stop when the door is opened
■ Overload protection in transfer area between shredder and press
■
■
■
■
Safety switch on the loading door of the press
Safety lock on the bale ejection door
Safety switch for machine standstill in the event of missing or moved press
Motor protection via thermal sensor and overcurrent protection relay
Advantageous
Sturdy bales and
low-dust handling
■
Practical additional benefit
■ Separate insertion slot to reduce
volume of small cardboard boxes
in the pressing chamber
Practical extension: dust extractor
■ Prepared as standard for connection of a dust extractor
■ Significant improvement in room climate and working conditions
■ Space-saving, mobile positioning next to the shredder
Documentation High Security Heavy Duty Shredders VZ 14.00 / Page 3 of 5
Technical changes and colour variances reserved; issue 02/2012
MARTIN YALE International GmbH, D-88677 Markdorf • Tel. +49(0)75 44 / 60-0 • vertrieb@martinyale.de • www.intimus.com
High Security Heavy Duty Shredders
VZ 14.00
Perfect, easy operation
■ Lockable main switch to protect
against unauthorised use
■ Selection switch for manual/automatic operation
■ Clear, robust buttons for On / Off and Reverse on both cutters
■ Visual operating status displays for both cutters and the press
Trouble-free operation
All machine functions controlled via programmable
logic control (PLC)
■ Automatic reverse for both cutters with subsequent
restart in the event of overload
■ Fully automatic control of the complete system in automatic mode
■
Unique feed technology
Integrated conveyor belt transports the material
to the primary shredder shredder
■ Both cutting units easily accessible for maintenance
■
Optimum all-round safety
Comprehensive safety equipment at all important
operating points to protect operator and machine
■
VZ 14.00/4
VZ 14.00/5
Security Level
DIN 32757-1 Level 4 DIN 32757-1 Level 5
Size of Shreds
mm
2 x 15
2 x 4.5
Shredding Capacity1Sheets
90-100
90-100
Shredding Capacity2kg/h
250150
Cutting Speed approx. m/sec
0.24
Working Width
approx. mm
500
Press Force
approx. kN
Bale Weight3kg
Transport Packaging
■ Packed in a wooden crate
■ Dimensions L x W x H
Shredder
2,490 x 1,360 x 1,730 mm
Baler
2,260 x 980 x 940 mm
■ Weight with packaging 1,580 kg
Noise Level
dBA
Power Supply
Volt
80
60-80
74
400 / 3ph
Motor Power
kW
11.3
(4 kW Pre-Shredder + 3.3 kW Post-Shredder + 4 kW Baler)
Dimensions L x B x H
Weight mm3,030 (with bale-ejection flap open 3,660) x 1,200 x 1,670
kg1,370
1
based on 70 g/m2 A4 paper. Sheet capacities vary depending on quality, weight, grain of paper and sufficient
power supply. It may be lower if the voltage is below the rated/nominal value.
2
depending on feeding, material and power supply, with cutters in mint condition
3
depending on material and cutting width
Documentation High Security Heavy Duty Shredders VZ 14.00 / Page 4 of 5
Technical changes and colour variances reserved; issue 02/2012
MARTIN YALE International GmbH, D-88677 Markdorf • Tel. +49(0)75 44 / 60-0 • vertrieb@martinyale.de • www.intimus.com
Installation instructions
intimus VZ 14.00/4 und VZ 14.00/5
High Security Heavy Duty Shredders
Scale 1:40
Shredder:
Operator‘s
position
Dimensions mm
[1] Length 3,030
[2]
[2] Length
with bale ejection flap open 3,660
[3] Height 1,670
[4] Inlet height or desk height 1,305
[5] Width 1,200
[1]
[3]
Baling press:
Operator‘s
position
Required space / distances mm
[1] min.
600
[3] min. 800
[2] min.
1,000
[4] min. 1,200
Position of controls
Power Supply 3 Phase
- Power lead = 5.10 m
- 400-415 V / 50 Hz supplied with
Cekon CEE 32 A plug, 5-pin
- other voltages on request
Required Fusing by customer
- Circuit breaker with tripping characteristic C
- or fuse gL/gG Classification type 1
as per IEC/EN 60947-4-1
[4]
400-415 V / 50 Hz = 35 A slow blow
220-230 V / 50-60 Hz = 40 A slow blow
200 V / 50-60 Hz = 63 A slow blow
[3]
[4]
[1]
[5]
[2]
Documentation High Security Heavy Duty Shredders VZ 14.00 / Page 5 of 5
Technical changes and colour variances reserved; issue 02/2012
MARTIN YALE International GmbH, D-88677 Markdorf • Tel. +49(0)75 44 / 60-0 • vertrieb@martinyale.de • www.intimus.com
Download PDF
Similar pages