(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
OWNER’S MANUAL
English
108
GS
I­­­ MPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
Krystal Clear™
Model 636G Filter Pump
12 V~, 50 Hz, 15 A
Hmax 1.0 m, H min 0.19 m, IPX5
Max. Water Temperature 35 °C
For illustrative purposes only.
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves the
right to change specifications and appearance, which may result in
updates to the instruction manual, without notice.
©2012 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O
Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European
Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
108-*GS-R0-1307
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
Warnings.......................................................................... 3
Parts List & Reference................................................... 4-6
Setup Instructions.......................................................... 7-10
Operating Instructions................................................... 11
Maintenance.................................................................... 12-13
Pool Care and Chemicals............................................... 12
Long Term Storage..........................................................13
Troubleshooting Guide...................................................14
Common Pool Problems.................................................15
General Aquatic Safety...................................................16
Limited Warranty............................................................. 17
SAVE THESE INSTRUCTIONS
108
GS
TABLE OF CONTENTS
English
Page 2
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
IMPORTANT SAFETY RULES
Read, understand and follow all instructions carefully before installing and using this product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
• To reduce the risk of injury, do not permit children to use this product. Always supervise children and those with disabilities.
• Children must stay away from this product and electrical cord(s).
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. They must at all times be supervised by a knowledgeable and experienced adult
responsible for their safety.
• Assembly and disassembly by adults only.
• Risk of electric shock. Connect transformer only to a grounding type receptacle
protected by a ground-fault circuit interrupter (GFCI) or residual current device (RCD). Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, which has a maximum rate of 30mA. Do not use a portable residual current device (PRCD).
• Always unplug the transformer from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product.
• The plug must be accessible after produc­­­t is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and other equipment.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to connect unit to electric supply; provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
• Keep the transformer more than 3.5m away from the pool.
• Keep the plug of the transformer more than 3.5m away from the pool.
• Position this product away from the pool, so as to prevent children from climbing on it and accessing the pool.
• Do not operate this product when the pool is occupied.
• This product is for use with storable pools only. Do not use with permanently installed pools. A storable pool is constructed so that it may be readily disassembled for storage and reassembled to its original configuration.
• This product is intended to be used only for the purposes described in the manual!
108
GS
SAFETY RULES
English
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and danger. Please use common sense and good judgement when enjoying any water activity.
SAVE THESE INSTRUCTIONS
Page 3
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
108
GS
PARTS LIST
English
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
SAVE THESE INSTRUCTIONS
Page 4
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
1
2
3
4
5
6
8
8
3
2
7
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
4
QTY. ­­­­­­SPARE PART NO.
10749
1
10460
2
AIR RELEASE VALVE/SEDIMENT RELEASE VALVE
10264
2
VALVE O-RING
10750
1
FILTER HOUSING COVER
5
FILTER HOUSING O-RING
1
6
FILTER CARTRIDGE (59900)
1
7
PUMP HOSE WITH NUTS
2
10493
8
TRANSFORMER
1
10985
DESCRIPTION
REF. NO.
1
THREADED FILTER HOUSING COLLAR
2
3
108
GS
PARTS REFERENCE
English
10325
When ordering parts, be sure to quote the model number and part numbers.
SAVE THESE INSTRUCTIONS
Page 5
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
11
12
13
14
15
9
10
11
12
13
14
9
10
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
DESCRIPTION
QTY. ­­­­­­SPARE PART NO.
REF. NO.
9
PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED)
2
10747
10
HOSE O-RING
10262
11
STEP WASHER
12
STRAINER NUT
2
10256
13
FLAT STRAINER RUBBER WASHER
2
10255
14
THREADED STRAINER CONNECTOR
2
11235
15
ADJUSTABLE POOL INLET NOZZLE
1
11074
10745
108
GS
PARTS REFERENCE
English
When ordering parts, be sure to quote the model number and part numbers.
SAVE THESE INSTRUCTIONS
Page 6
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. The plunger valve assembly prevents water from flowing into the
filter pump while the filter cartridge is being placed or cleaned. If your pool
has an inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The parts numbers here onward, refer to the
parts depicted in the Parts List section of this manual. To install, do the
following:
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (14) (see drawing 1). Be careful not to lose the step rubber washer (11). Place the plunger valve on the ground in a safe place.
2. In a counter-clockwise motion unscrew
the strainer nut (12) from the threaded
connector (14). Leave the flat
washer (13) on the connector (14).
3. Install the strainer and plunger valve at the lower position of pool outlet (marked "+").
From the inside of the pool liner insert
the connector (14) into one of the
pre-cut holes with the washer remaining on the connector to be placed against
the inside of the liner wall.
4. Before assembly, lubricate the threads with a petroleum jelly. Then, with the flat side of the strainer nut (12) facing the
outside wall of the liner in a clockwise motion screw the strainer nut (12) back onto the threaded connector (14) (see drawing 2).
5. Finger tighten the strainer nut (12) onto the threaded connector (14).
6. Grasp the plunger valve assembly. Make
sure the step washer (11) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (14) (see drawing 3).
8. In a clockwise motion turn the plunger valve handle to close position. Ensure the plunger valve is securely closed. This will prevent water from flowing out during
filling of the pool (see drawing 4).
1
2
1
INSIDE
LINER WALL
12
SAVE THESE INSTRUCTIONS
13
2
14
3
1
2
4
INSIDE
LINER WALL
108
GS
SETUP INSTRUCTIONS
English
Page 7
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
POOL INLET - NOZZLE & PLUNGER VALVE SETUP
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (14) (see drawing 5). Be careful not to lose the step rubber washer (11). Place the plunger valve on the ground in a safe place .
2. In a counter-clockwise motion unscrew
the strainer nut (12) from the threaded
connector (14). Leave the flat
washer (13) on the connector (14).
3. Install the nozzle and plunger valve at the upper position of the pool inlet. From the inside of the pool liner insert the connector (14) into one of the pre-cut holes with the washer remaining on the connector to be placed against the inside of the liner wall.
4. Before assembly, lubricate the threads with a petroleum jelly. Then, with the flat side of the strainer nut (12) facing the outside wall of the liner in a clockwise motion screw the strainer nut (12) back onto the threaded connector (14) (see drawing 6).
5. Finger tighten the adjustable pool inlet nozzle (15) and the strainer nut (12) onto the threaded connector (14).
6. Grasp the plunger valve assembly. Make
sure the step washer (11) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (14) (see drawing 7).
8. In a clockwise motion turn the plunger valve handle to close position. Ensure the plunger valve is securely closed. This will prevent water from flowing out during
filling of the pool (see drawing 8).
9. Adjust the direction of the nozzle head pointing away from the pool outlet for a better circulation result (see drawing 9).
10. The pool liner is now ready to be filled with water. Consult the above-ground-
pool owner’s manual for the filling
instructions.
5
2
1
INSIDE
LINER WALL
12
SAVE THESE INSTRUCTIONS
13
14
6
15
7
1
2
8
INSIDE
LINER WALL
9
Pool
WATER
FLOW
108
GS
SETUP INSTRUCTIONS
English
Page 8
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
SETTING UP FILTER PUMP
For your own personal safety, it is very important that you place your transformer
more than 3.5m away from your pool.
­3.5 m
FILTER PUMP STATIONARY MOUNTING OPTION
Some countries, especially in the European community, require the filter-pump to
be secured to the ground or to a base in a permanent upright position. Check your
local authorities to determine if there is a regulation in your area regarding above-the-ground swimming pool filter-pumps. If yes, then the filter-pump can be
mounted to a platform using the two holes located in the base. See drawing below.
130 mm
The filter-pump can be mounted on a cement base or onto a wooden platform to
prevent accidental falling over. Total assembly must exceed 18kg.
1. The mounting holes are 6.4mm in diameter and spaced 130mm apart.
2. Use two bolts and lock nuts with a maximum of 6.4mm in diameter.
SAVE THESE INSTRUCTIONS
108
GS
SETUP INSTRUCTIONS
English
Page 9
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
FILTER PUMP HOSE CONNECTION SETUP
­­­1. Remove the Krystal Clear™ filter pump and hoses from the packaging.
2. Place the filter pump in such a manner, that you can easily assemble the
hose (7) connections to the plunger valve.
Note: Some regional regulations may require the filter pump to be mounted on a stationary platform. There are two mounting holes located in the pump base for this reason. Consult your local authorities for
filter-pump mounting requirements.
3. Grasp the two pump hoses (7) and connect the hose nuts to the filter pump.
4. In a counter-clockwise motion unscrew the threaded filter housing collar (1) from the filter housing. Place it in a safe place.
5. The filter pump is an airtight system. Turn the top air release valve (2) once or twice in a counter-clockwise motion. DO NOT remove the air release valve from the top cover, as water will expel with force if the motor is turned on. This may cause injury.
6. Grasp and remove the filter housing cover (4). Check to see if a cartridge is inside the housing. If yes, replace the cover, finger tighten the housing
collar (1) back onto the filter housing.
7. Gently finger tighten the sediment release valve located at the bottom of the housing to be sure that water does not leak out.
8. When the pool is filled connect the hose from the bottom of the filter housing to the highest strainer assembly. You will find the hose connection at the bottom of the plunger valve assembly. Use
­­­
the hose nut to attach the hose.
9. Connect the second hose which is fixed to the middle of the motor housing to the remaining liner connection.
WARNING
Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.
PLUNGER VALVE
ASSEMBLY
HOSE NUT
FILTER HOUSING
COVER
MOTOR
HOUSING
ADJUSTABLE POOL
INLET NOZZLE
OUTLET HOSE
INSIDE LINER
WALL
THREADED FILTER
HOUSING COLLAR
FILTER CARTRIDGE
INSIDE
AT
ER
FLOW
AIR RELEASE
VALVE
WATER LEVEL
THREADED
STRAINER
CONNECTOR
W
ER
WAT
HOSE O-RING
TRANSFORMER
OW
FL
INLET HOSE
OUTSIDE LINER
WALL
(ILLUSTRATION NOT TO SCALE)
The installation instruction shall provide information on requirements specified for
the electrical installation and shall include reference to national wiring rules.
SAVE THESE INSTRUCTIONS
108
GS
SETUP INSTRUCTIONS
English
Page 10
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
OPERATING INSTRUCTIONS
1. Make sure the filter pump is switched off. The switch is located on the motor housing.
2. Connect the filter pump power cord end to the transformer output receptacle and screw in the cover. Plug the transformer power cord into a properly installed electrical socket.
WARNING
Risk of electric shock. Connect transformer only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI) or residual
current device (RCD). Contact a qualified electrician if you cannot verify
that the receptacle is protected by a GFCI/RCD. Use a qualified electrician
to install the GFCI/RCD, which has a maximum rate of 30mA. Do not use a
portable residual current device (PRCD).
3. Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valve, allowing water to flow into the filter pump.
4. With water flowing into filter pump, the water pressure will allow the air trapped inside to escape from the air release valve (2). When all the air has escaped water will flow out of the valve (2). When this occurs gently finger tighten the valve (2) in a clockwise direction.
5. Turn on the switch. The filter pump is now filtering the water.
6. Operate the filter pump until the desired water clarity is obtained. But take very
good care not to overheat the motor.
IMPORTANT
To prevent air lock, open the lower plunger valve (connected inlet hose)
first and then the upper plunger valve (connected outlet hose). Open the
air release valve, wait until water starts to flow out of the air release valve,
close air release valve.
SAVE THESE INSTRUCTIONS
108
GS
OPERATING INSTRUCTIONS
English
Page 11
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
POOL CARE AND CHEMICALS­
• All pools require care to keep the water clear and hygienically clean. With
proper chemical control, your filter will help attain this objective. Consult your pool supply dealer for instructions regarding the proper use of chlorine,
algaecide and other chemical agents required for sparkling clear water.
• Keep pool chemicals away from children.
• Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations could occur.
• Daily pH checking and chemical treatment of the water is very important and cannot be overemphasized. Chlorine, algaecide and maintenance of proper pH levels are required when filling the pool as well as during the season. Consult your local swimming pool supply store for instructions.
• The season's first filling of the pool may have brackish water requiring extra water additives and extra filter changes. Do not allow swimming in pool until the pH level is balanced. Consult your local swimming pool supply store for
instructions.
• Keep spare filter cartridges on hand. Replace cartridges every two weeks.
• Chlorinated water may damage lawns, gardens or shrubbery as children play in the pool and splash water outside the pool. Lawn areas underneath the pool liner will be destroyed. Note that some types of grass may grow through the liner.
• Filter run time depends on pool size, weather and usage level. Experiment with various run times so as to produce clean clear water.
CAUTION
Concentrated chlorine solutions may damage the pool liner. Always follow the chemical manufacturer’s directions, and the health warnings.
CLEANING OR REPLACING FILTER CARTRIDGES
108
GS
MAINTENANCE
English
It is recommended that the filter cartridge be replaced at least
every 2 weeks.
1.
2.
3.
4.
5.
6.
Make sure the filter pump is turned off, then unplug the transformer power cord from the electrical socket.
Grasp a plunger valve handle. Turn the handle counter-clockwise, push down until it stops and then turn it clockwise until the plastic protruding notch anchors in the "0/1" position. Repeat for the second plunger valve. This prevents the water from flowing out of the pool.
Gently turn the top air release valve once or twice in a counter-clockwise
direction. The housing cover can now be easily removed.
In a counter-clockwise direction remove the filter housing collar (1). Place it in a safe location.
Remove the housing cover (4).
Now remove the used filter cartridge.
SAVE THESE INSTRUCTIONS
Page 12
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
CLEANING OR REPLACING FILTER CARTRIDGES (continued)
7. Examine the inside of the filter housing.
8. If dirt or sediment is located on the bottom of the housing then:
A. In a counter-clockwise motion gently unscrew and remove the sediment valve (2) located at the bottom of the housing. Place it in a safe place.
B. With a bucket of water or a garden hose pour water into the housing flushing out the sediment.
C. Screw back the sediment valve (2) in a gentle clockwise motion. Do not over-tighten.
9. Place a new cartridge filter in the housing.
10. Return the housing cover (4) to its position and in a clockwise direction rescrew the housing collar (1) onto the filter housing.
11. Turn both plunger valve handles in a counter-clockwise direction, pull up until they stop, and then turn them clockwise until the metal protruding notch anchors in the "0/1" position.
12. When the trapped air has escaped through the air release valve gently retighten the valve (2) in a clockwise direction.
13. Reconnect the power cord.
14. Turn on the pump.
LONG TERM STORAGE
1. Before emptying your pool for long term storage, or relocation, be sure the water is directed towards an acceptable drain water receptacle away from the house. Check local regulations for specific directions regarding disposal of swimming pool water.
2. Disconnect power cord from electrical outlet.
3. Now, drain the pool.
4. When the pool is empty, disconnect all hoses from the pump and plunger valves and remove the strainers from the pool wall.
5. Drain all water from the filter pump.
6. Leave filter pump pieces & hoses outside to thoroughly air dry.
7. Twist the plunger collar counter-clockwise removing the water flow control mechanism from the plunger housing.
8. Coat the following O-rings and washers with petroleum jelly for long term storage:
• Air release valve & sediment O-rings (3).
• Filter housing cover O-ring (5).
• Pump hose O-rings (10).
• Strainer valve assembly step washers (11).
• Flat strainer rubber washers (13).
9. Discard the used filter cartridge. Put aside 1 or 2 new cartridges for next
season’s use.
10. It is best to place all dry pieces in the original packaging for storage or place them in an airtight plastic bag.
11. Store the unit and accessories in a dry place. The storage's temperature should be controlled, between 32 degrees Fahrenheit (0 degrees Celsius)
and 104 degrees Fahrenheit (40 degrees Celsius) storage location.
108
GS
MAINTENANCE
English
IMPORTANT
It is best to store away your poolsystem in its original packaging.
SAVE THESE INSTRUCTIONS
Page 13
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
TROUBLESHOOTING GUIDE
TROUBLE
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POOL
CAUSE
• The motor is not plugged in.
• The Fuse box needs checking.
• The GFCI/RCD circuit breaker is tripped.
• Motor too hot and overload protection is shut off.
­
• Improper chlorine or pH
levels.
• Filter cartridge is dirty.
• Damaged cartridge.
• Excessively dirty pool.
• The strainer screen is
restricting the water flow.
SOLUTION
• Filter cord must be plugged into a 3 wire outlet that is protected by a Class A Ground Fault Circuit Interrupter, or RCD.
• Reset circuit breaker. If circuit breaker
trips repeatedly, your electrical system
may have a defect. Turn off circuit
breaker and call an electrician to correct the problem.
• Let the motor cool down.
• Adjust the chlorine and pH level. Consult your local swimming pool
supply stores.
• Clean or replace cartridge.
• Check the cartridge for holes. Replace if damaged.
• Operate the filter for longer periods.
• Clean the strainer screen at the inlet.
FILTER DOESN’T
PUMP WATER OR
THE WATER FLOW
IS VERY SLOW
• Clogged inlet or discharge.
• An air leak on the intake line.
• Scale or buildup on cartridge.
• Excessively dirty pool.
• Dirty filter cartridge.
• The nozzle and strainer connection are reversed.
• Clear any obstructions in the intake hose by discharging it inside pool wall.
• Tighten hose nuts, check hoses for
damage, check pool water level.
• Replace cartridge.
• Clean cartridge more often.
• Clean inside the plunger valve.
• Pull valve handle to full upright position.
• Install the nozzle at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet.
PUMP DOESN’T
WORK
• Low water level.
• Strainer screen plugged up.
• An air leak on the intake hose.
• Faulty motor or the impeller is jammed.
• An air lock inside the cartridge chamber.
• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose nuts, check hose for damage.
• Clear any sticks or leaves in the
intake hose.
• Turn and pull valve handle to full upright position.
TOP COVER
LEAKING
• O-ring missing.
• Cover is not tight.
• Filter cartridge is dirty.
• Remove cover & check for O-ring.
• Tighten cover (Manually).
• Replace or clean cartridge.
HOSE LEAKING
• Hose nuts are not well-fitted.
• Tighten or reinstall hose nut.
AIR LOCK
• There’s air trapped in the pump housing and inlet hose.
• The inlet and outlet hoses connection are reversed.
• Open air release valve, wait until water starts to flow out of the valve, then close it.
• The lower position of pool outlet
connects to filter pump water inlet. The upper position of pool inlet connects to filter pump water outlet.
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service
Department for assistance. See separate “Authorized Service Centers” sheet.
SAVE THESE INSTRUCTIONS
108
GS
TROUBLESHOOTING GUIDE
English
Page 14
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
COMMON POOL PROBLEMS
PROBLEM
DESCRIPTION
CAUSE
SOLUTION
ALGAE
•Greenish water.
•Chlorine and pH levels • Super chlorinate with shock •Green or black need adjustment.
treatment. Correct pH to your spots on pool liner.
pool store's recommended •Pool liner is
level.
slippery and/or has • Vacuum pool bottom.
a bad odor.
• Maintain proper chlorine level.
COLORED
WATER
•Water turns blue, brown, or black when first treated with chlorine.
•Copper, iron or
manganese in water being oxidized by the added chlorine. This is common.
• Adjust pH level to the
recommended level.
• Run filter until water is clear.
• Clean cartridge frequently.
FLOATING
MATTER IN
WATER
•Water is cloudy or milky.
•"Hard water" caused by a too high pH level.
•Chlorine content is low.
•Foreign matter in water.
• Correct the pH level. Check with your pool dealer for advice.
• Adjust the chlorine level.
• Clean or replace your filter.
CHRONIC
LOW WATER
LEVEL
•Level is lower than •Rip or hole in pool on previous day.
liner or hoses.
•The drain valves are loose.
• Repair with a patch kit.
• Finger tighten all caps.
SEDIMENT
ON POOL
BOTTOM
•Dirt or sand on pool floor.
•Heavy use, getting in and out of pool.
• Use Intex pool vacuum to clean bottom of pool.
SURFACE
DEBRIS
•Leaves, insects etc. •Pool too close to trees.
• Use Intex pool skimmer.
SAVE THESE INSTRUCTIONS
108
GS
COMMON PROBLEMS
English
Page 15
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all risks and or dangers.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally recognized Safety Organizations:
• Demand constant supervision. A competent adult should be appointed as a “lifeguard” or water watcher, especially when children are in and around the pool.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is supervising pool users about potential pool hazards and about the use of protective devices such as locked doors, barriers, etc.
• Instruct all pool users, including children what to do in case of an
emergency.
• Always use common sense and good judgement when enjoying any water activity.
• Supervise, supervise, supervise.
SAVE THESE INSTRUCTIONS
108
GS
SAFETY GUIDELINES
English
Page 16
(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012
English
108
GS
LIMITED WARRANTY
Your Krystal Clear™ Filter-Pump has been manufactured using the highest quality
materials and workmanship. All Intex products have been inspected and found free of
defects prior to leaving the factory. This Limited Warranty applies only to the Krystal
Clear™ Filter-Pump and accessories listed below.
The following provision is only valid within the European member states countries: The
legal regulation of Directive 1999/44/EC will not be effected by this Intex warranty.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this manual, as proof of purchase will be required and must accompany warranty claims or the Limited Warranty is
invalid.
Krystal Clear™ Filter-Pump Warranty – 1 Year
Hoses, Plunger Valves & Fittings Warranty – 180 days
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in the separate “Authorized Service Centers” sheet.
The Service Center will determine the validity of the claim.
IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY AND IN
NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR EMPLOYEES BE LIABLE
TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL DAMAGES OR LIABILITIES. Some countries, or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
This Limited Warranty does not apply if the products are subject to negligence, abnormal
use or operation, accident, improper operation, improper voltage or current contrary to
operating instructions, or to damage by circumstances beyond Intex’s control, including but
not limited to, ordinary wear and tear and damage caused by exposure to fire, flood,
freezing, rain, or other external environmental forces. This Limited Warranty applies only to
those parts and components sold by Intex. The Limited Warranty does not cover
unauthorized alterations, repairs or disassembly by anyone other than Intex Service
Center personnel.
The Limited Warranty is also not applicable if this product is used with another product
other than an Intex product, when setting up your pool.
The costs associated with the loss of pool water, chemicals or water damage are not covered by this warranty. Injury or damage to any property or person is not covered by this
warranty.
SAVE THESE INSTRUCTIONS
Page 17
Download PDF
Similar pages