PRELIMINARY DOCUMENT LEADERSHIP, INTEGRITY, QUALITY OTG 15W PORTABLE EMERGENCY POWER SYSTEM OWNERS AND OPERATION MANUAL www.linortek.com IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury to a person and serious damage to the unit. Use only with a stand, tripod, bracket, or mount recommended by the manufacturer, or sold with the product. Any mounting of the unit should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 8. Ventilation - Openings in the enclosure, if any, are provided for ventilation and to ensure reliable operation of the unit and to protect it from overheating. These openings must not be blocked or covered. This unit should not be placed in a built-in installation unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 9. Power Sources - This unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply you plan to use, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions. 10. Grounding or Polarization - This unit may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Alternately, this unit may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 11. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance. 12. Power Lines - An outdoor system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outdoor system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 13. Overloading - Do not overload outlets and extension cords as this can result in a risk of fire or electric shock. 14. Object and Liquid Entry - Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit. 3 15. Servicing - Only remove the back cover in accordance with the included instructions to replace the Sealed Lead Acid (SLA) batteries or replace the battery fuse. Do not attempt other service to this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all other servicing to qualified service personnel. 16. Damage Requiring Service - Unplug the unit from the outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation. e. If the unit has been dropped or the cabinet has been damaged. f. When the unit exhibits a distinct change in performance--this indicates a need for service. 17. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 18. Safety Check - Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition. 19. Coax Grounding - If an outside cable system is connected to the unit, be sure the cable system is grounded. U.S.A. models only-Section 810 of the National Electrical Code, ANSI/NFPA No.70-1981, provides information with respect to proper grounding of the mount and supporting structure, grounding of the coax to a discharge unit, size of grounding conductors, location of discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 20. Lightning - For added protection of this unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the unit due to lightning and power-line surges. 21. Outdoor Use - This unit is not water proof and should not be allowed to get wet. Do not expose to rain. Do not leave out-of-doors overnight as condensation may occurr. 22. While changing batteries or fuses be careful of eletrostatic discharge. It is best to use a grrouinded electronics service bench. If this is not available you can discharge yourself by touching a metal appliance or pipe. While changing the batteries or fuse do not touch i) any wires other than the battery wires and ii) the printed circuit board. LIMITATION OF LIABILITY IN NO EVENT WILL LINOR TECHNOLOGY BE LIABLE, WHETHER IN CONTRACT, TORT, OR OTHERWISE, FOR ANY INCIDENTAL, SPECIAL, INDIRECT, CONSEQUENTIAL OR PUNITIVE DAMAGES, INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, OR LOST PROFITS, SAVINGS, OR REVENUES TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. DISCLAIMER FOR CRITICAL APPLICATIONS This product is not intended or authorized for life support product or for other uses for which a failure could cause personal injury or death. If you or your customers use or permit the use of this product for such unintended or unauthorized uses, you agree to fully indemnify Linor Technology and its affiliates, and the officers, employees and distributors of each, from all liability related to such use, including attorneys’ fees and costs. This product contains SOFTWARE and is provided by THE PROVIDER "as is" and "with all faults." THE PROVIDER makes no representations or warranties of any kind concerning the safety, suitability, lack of viruses, inaccuracies, typographical errors, or other harmful components of this SOFTWARE PRODUCT. There are inherent dangers in the use of any software and THE PROVIDER will not be liable for any damages you may suffer in connection with using, this SOFTWARE PRODUCT. 4 U NPACKING WARNING: For additional safety disconnect the batteries by selecting "OFF" or "0" on the BATTERY switch. CAUTION: This product can and will break if the batteries are wired incorrectly. LINOR Technology assumes no responsibility for damaged products due to the user incorrectly attaching the batteries. Read the instructions through before attempting battery replacement. If you feel that you are unable to per-form this operation bring the unit to a small appliance or computer repair shop. Unpack carefully. This equipment should be handled with care. In order to prevent damage during shipping, the batteries for your unit are not installed. Carefully follow the instructions and cautions following for correct battery installation. If you bought your unit at a store, the batteries may be preinstalled. In either case, retain this manual in a safe place should you need to replace the batteries in the future. Use a pair of pliers and a Phillips screwdriver for the following proceedure. 1. Remove the AC power cord from the control panel. 2. Remove all cords from the control panel. 3. IMPORTANT - Disconnect the batteries from powering the unit by selecting "OFF" or "0" on the BATTERY switch. Check to ensure that the following items are included for the applicable model ordered: • Solar powered emergency battery unit. • Separate box with two batteries (if not pre-installed). • Removable 3-wire recharging cord. • Battery spacer ~2"x1"x3/8". • This manual. If an item appears to have been damaged in shipment, replace 4. Place the unit solar panel down on a clean surface with a it properly in its carton and notify the shipper. If any items are clear space above the unit so the top panel can be laid missing, notify LINOR Technology. down. The LED light should now be facing up. You might The shipping carton along with the handle box (double boxed) is want to put a towel or a piece of cardboard down to protect the safest packing in which the unit may be transported. Save it the top of a desk or table from being scratched. for possible future use. The handle box the unit comes in should 5. Remove the four #6 by 3/4 inch screws in each corner and not be used alone for shipping, but makes a suitable container place the screws in a small container or tray for safe for storing and transporting. keeping. Do not ship with the batteries installed. When you remove the cover in the following step there will be a wire that connects the LED light to the controller. Be careful not to pull on this wire or it might SERVICE break. Other than for replacing the SLA batteries, do not attempt 6. Carefully lift the cover with the LED light off the rest of the unit. service to this unit yourself as opening or removing covers may There is a wire connecting this panel to the main part. Without expose you to dangerous voltage or other hazards. Refer all moving it too far away, flip the cover over and place at the top of servicing to qualified service personnel. If your unit requires the main unit. service please contact LINOR Technology for information on how to obtain service. BATTERY REPLACEMENT The power storage devices used in this unit are sealed lead acid batteries (SLA). These batteries are chosen because of their simplicity, safety and long service life, typically 3 to 5 years under normal use. However, this comes at the cost of their weight. For this reason the unit is supplied with the batteries boxed separately. Carefully follow this procedure to initially install or replace the batteries: WARNING: To prevent electrical shock remove the AC power cord from the control panel. WARNING: For further safty remove all other cords from the control panel. 7. Remove the metal straps (2 pieces) that secure the batteries by unscrewing the #8 screw from each. Be careful not to drop the screw into the unit. Put them with the cover screws. 5 8. If you are installing the batteries for the first time skip to step 10. Never connect metal between the "+" and "-" terminals of the battery. Although there are not dangerous voltages present, there is high current (even in an exhausted battery) and this can cause a dangerous spark and even heat metal, such as a screwdriver to red hot which can cause serious burns. 9. Using pliers, carefully pull off the connectors from the batteries starting with the "–" or BLACK wires. Then remove the "+" or RED wires. Lift the two batteries from the unit. Do not lose the plastic spacer that is between the two batteries. The batteries are heavy. 10. Place the batteries into their respective slots With the plastic battery space removed in the previous step or supplied in the bag of parts if this is the first time batteries have been installed in the unit. The battery should be placed so that the terminals are on the right when the case is upright and the "+" terminals are on the outside. 11. Reattach the two metal battery straps by placing the long end through the metal opening in the bottom of the battery tray and fastening with the #8 screw removed in a previous step. Use care to make sure the wires are not pinched. previous step. The screw should go through the black plastic foot and into the internal bracket. Ensure that the panel is on all the way, but, do not over tighten. G ETTING STARTED Before using this product charge the batteries using one of the two methods described below. It is important to turn on the unit. The unit will not charge without the Battery Switch being in the ON (| ) position. The unit can be charged by using the built in solar panel. Make sure the solar panel is clean and is placed in as most direct sunlight as available. When there is enough light to charge the battery, the Solar Panel Indicator on the LCD will turn on. You can use the current monitor to help position the solar panel to get the maximum amount of charging current. In General , the solar panel should be directly perpendictular to the sun. As the battery capacity is 18 amp/hours, charging from the solar panel can take more than one day depending on the amount of power drained from the batteries. To charge the unit by household AC plug the unit in with the supplied line cord.The AC PLUG indicator on the LCD will turn on. If the unit is not turned on the unit will not charge. This system produces both 120VAC and 12VDC for powering a wide variety of devices as well as a USB port for powering or charging USB devices. It is useful for home or camp in use as emergency power or renewable energy. It is easy to operate with standard type power connectors, easy to carry and store. It also has a TIMER function for automatic operation. LOADs refers to the 110VAC outlet, 12VDC power outlet, USB outlet and the built in LED lamp. The system LOADs may be used while the unit is charging, but, the output power is still limited to the available battery energy plus the charging power from either the solar panel or AC line cord. 12 Locate the wires labeled positive (RED) and negative (BLACK). 13. Attach the negative (BLACK) wires to the negative "-" CONTROL PANEL (BLACK) terminal on the batteries. Make sure you have connected the proper wire to the proper terminal. 14. Attach the positive (RED) wires to the positive "+" (RED) terminal on the batteries. Make sure you have connected the proper wire to the proper terminal. 15. Carefully recheck that the RED wires are attached to the "+" terminals of the batteries and the BLACK wires are attached to the "-" terminals of the battery. 16. If you disconnected the LED light wires, reconnect them at this time. 17. Position the back panel over the unit, align the four corners and gently tap with your fingers the panel all the way in. 18. Attach the back panel with the four #6 screws removed in a • USB Charger - This port provides regulated +5VDC to USB devices. It is limited to 500mA. The power on this port is enabled whenever the STBY switch is in the UP or ON position. 6 • LCD Display - The LCD display provides details on battery level and power drain. The drain is measured in amps A (or milliamps mA).The system will limit the current to about 10A. • Load Switches - The three main functions, AC, DC and the LED light have individual On/Off switches.When this switch is moved to the UP position, the load is enabled and will turn on based on the position of the STBY Switch. • Menu Push Button - Is used to navigate through the menus on the LCD display. This switch as two modes. A TAP is a short push, and HOLD means to hold the button in. • STBY Switch - This is the master switch to turn on the unit. When this switch is down, the unit is in standby and the loads will not be on. If the load switches are on, they will be displayed on the LCD as *AC, *DC, *LED. When this switch is in the UP or ON position, any load that has it's switch on the UP (ON position) will be turned on. In this case the LCD will show +AC, +DC, +LED • Reset - A toothpick or similar nonmetal object can be used to reset the internal computer chip without turning the unit off. • DC Output - This standard "cigarette lighter style" outlet provides 12VDC output at 5A.The center conductor is positive. • Battery - This switch will disconnect the batteries. If the unit is to be stored, turning this switch to the OFF position will remove all power drain from the batteries for the longest storage life. It is not necessary to turn the unit off under normal circumstances between uses. This switch should be turned off whenever the unit is opened up to change the batteries. • AC Output - This connector provides 120VAC at 120 watts. If 150 watts is exceed or the batteries become low, the system will automatically switch the AC off. • AC Input - You can use the supplied line cord to plug the unit into a household outlet to recharge the battery. AC voltage should be in the range of 100~240VAC. This connection is also fused with a 2A fuse for safety. N AVIGATING When the unit is powered on the LCD screen shows the HOME PAGE. After a brief period it automatically transitions to a screen with the product model number and software version number. These pages can be skipped by pushing the menu button on each page. After another delay the MAIN screen that consists of a status area (showing "SBY" here), three indicators and the battery Auto charge bar. The status bar tells you whether the unit is in "ON" ,"SBY" (standby) or AUTO mode, and cycles through which outputs are activated. These outputs are AC, DC and LED (for the LED light). Preceding each is "*" for in standby, a "+" for on and a "!" for an error. This area will flash showing the system is properly running. • "ɸ" or "-" : The first indicator shows if an automatic mode is on. • or : The next shows if the unit is receiving power from the solar panel or if it is plugged in. • or or : The third indicator shows if the unit is charging. An empty battery means the battery is low. A half battery means it is charging. A full battery means the charging is complete. A "?" means there is a charging error. While the battery has a full charge, the status indicator may switch between the half and full battery as the unit does a maintenance charge. 7 The charge bar at the bottom of the screen gives an indication of how much charge remains in the battery. The system LOADs may be used while the unit is charging, but, the output power is still limited to the available battery energy and the charging power from either the solar panels or AC line cord. To navigate through the menus on the LCD display use the MENU button which has two modes: One TAP is a short push. HOLD means to hold the button in. If the screen is dark, the first push of the button will wake the screen up. From the main screen, a MENU button HOLD will transition the display to the battery information screen. It initially displays the batteries' voltage. A TAP will alternate between the voltage and the current displays. A HOLD press on the battery information screen will move to the programmable options screen. While on the GoBACK screen a HOLD will exit the program mode back to the battery level screen. A TAP will go to the next page. Now, pressing hold will put the program option in brackets (). Once the brackets are on, a TAP will increment the option. A button HOLD will remove the brackets and TAP to move onto the next option. You must navigate to the [GoBACK] page and HOLD to return to the information pages. The screen will automatically reset to the information page if no presses are made for a few seconds. There are two programmable MODES to select from, AUTOon will turn the system from SBY to ON when the solar panel no longer receives sufficient sunlight (adjustable in later settings) and go back to standby after the specified duration (adjustable in later settings). If the system is already ON, it will go to SBY after the specified duration. SLEEP mode may also be selected, which will automatically turn the loads off after the specified duration has expired. Notes: 1. In these automatic modes, the STBY/ON switch may not represent the current state as shown on the LED and LCD display. 2. If a mode is set, a "ɸ" will be shown in the AUTO area of the LCD display. 3. While active, the status area will show AUTO, 4. The hour timer used is only approximate. To adjust the amount of time the unit is ON in either automatic mode, navigate to the DURATION page, press HOLD to remove the brackets and set the ON time [1 to 12 hours]. HOLD again to save and navigate to exit. For the AUTO on mode, the light level can be manually set in the same way as the DURATION. Navigate to the SP page. The value of the light on the panel is displayed for reference. The value may be set from 1 to 16, the default is 4. There is a 5 minute delay once the SP threshold is meet to allow for the sun to set. The OTG 15W is also capable of send and SOS signal by flashing the high brightness 3 watt LED on the side on the case. This signal will be sent about 3 times a minute and will last under the monitored battery power for about 2 weeks. Buy charging the unit by day and running the distress signal by night, it should be able to run indefinately. Navagate to this screen in the programable options mode to turn this option ON and OFF. The state of this option is stored in the systems permanent memory. As discussed later in greater detail, the system has a real time battery monitor that will try to prevent deep discharges on the batteries. Although these deep discharges are permisable, they will eventually damage the batteries and shoud be avoided in normal operation. The default condition is to have this monitor turned on. Navagate to this screen in the programable options mode to turn this option ON and OFF. The state of this option is stored in the systems permanent memory. OPERATION Operation of the unit is simple. Use the three load switches to separately turn ON or off the AC, DC or LED light devices. Keeping the unused loads OFF will extend battery power by lowering power drain. Use the STBY/ON switch to turn on the enabled loads. This switch will also always enable the USB power plug. When using either the AUTOon or SLEEP modes, whatever loads are enabled will turn on under the pre-programmed conditions. The LED light can be turned on and off via its control switch, and is useful as an emergency flashlight in situation such as power outages. Another good use is to set the unit on a window sill and use the AUTOon mode to turn on the light. So as the sun goes down, your light comes on automatically. The back-light on the LCD panel will time out after a few seconds of non use. When this happens, the LED above the STBY switch will also go into a flash mode.This will save battery power and any activity on the switches will turn the lights back on. If the lights are off, the first tap of the MENU button will have no effect other to turn the lights back on. It is important to realize that any power used from the batteries needs to be replaced by recharging. For each amp of current out, at least one amp of current must be put back in for the same period. For example: If the AC out is used for a 60 watt light bulb for an hour, that's about 5 amps for an hour or 5 AH. When plugged in, about 2 amps of current is available for recharging, in this case it will take about 8 hours to fully recharge. This screen shows the unit recharging from the AC plug with the batteries at 13.4V, this voltage will increase to about 14.5V as the batteries complete their charge. If recharging with the solar panel, about 750mA is available, it could take up to 24 hours of direct sunlight for a full recharge from a low battery state. This screen shows the unit recharging from the solar panel with 415mA going into the batteries. The unit can be moved and positioned toward the sun to maximze the recharge current. Maintaining full power with the solar panel requires a good sunny day and continual reposition of the unit to face the sun. This is true of any solar panel system and shows why it is important to conserve power while using the system. Use the LCD display to help you see how much power you are using. 8 The LED light uses about 350mA and can run for over 50 hours on the batteries. Following is a chart that demonstrates how battery life decreases as power drain increases. M AINTENANCE • Before using this product, charge built-in battery under the direct sunlight through solar panel or AC line cord. • Keep in a dry environment. • Keep away from Children. • When not in use, the unit should be fully charged before storage and the BATTERY switch put in the OFF position. This will maximize storage time. • The unit should be recharged twice a year, even if not used. This will ensure that power is always available in an emergency and provide maintenance to maiximize batery life. • Although the unit needs to be placed in the sun, arrange it as to minimize the heat around the unit. For example, place the unit on a table or a box rather than on hot blacktop. Do not keep the system in high temperature environment for extended periods. • Clean the unit with a soft cloth. Use window cleaner by spraying first onto the cloth then wiping down the unit. Pay special attention to keeping the solar cell clean • DO NOT SPRAY LIQUID DIRECTLY ONTO THE UNIT. • The Solar Panel is covered with a sheet of glass. IT WILL BREAK IF STRUCK. OTHER I TEMS There is a regular type 5X20 mm cartridge fuse that will blow instantly and prevent currents higher than 16 Amps on the internal parts. This protects the wires, switches and others parts from excessive current and heat. On newer units, the BATTERY switch has been replaced by a circuit breaker type switch. This has the added benifits of being able to be reset without opening the unit. In addition, the circuit breaker will add additional protection duniting the install/replace batteries processes. The AC inverter also has protection that will prevent more than 150 watts being drawn on it. This is approximately 12.5 Amps. The DC circuit has a PTC type resettable fuse that is set for 8 Amps. This is a very slow type fuse, but if higher currents are drawn fo a period of time, this fuse will trip. It will not effect the other circuits and will self reset after a few minutes. There is also a software based monitor that will automatically remove loads should the current exceed about 13 Amps. This monitor is provided to prevent the internal fuse from being blown but it is not a fail safe like the internal fuse. High currents cannot be drawn from the AC and DC circuits simultaneously. If the unit drops to STBY, remove some of the power load and then simply turn the STBY switch OFF and then ON again. The system also monitors the battery voltage for low volts. The AC inverter has its own protection and will switch off at about 10.5 volts. In this case it turns itself off. There is also a software based battery monitor. This monitor will measure voltage in relation to current to determine if the unit should shut down. Using this battery monitor will ensure the longest usable battery life. However, should you need to use whatever power is available, such as in an emergency, this monitor can be disabled in the programable mode menu as detailed in the section titled NAVIGATING above. This table shows the aproximate battery voltage that the smart battery monitor will use to turn off the system. It is realative to the current being used because that is the nature of the SLA battery. SMART BATTERY M ONITOR mA 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475 500 SD Volts 11.15 11.14 11.14 11.14 11.13 11.13 11.13 11.13 11.12 11.12 11.12 11.11 11.11 11.11 11.10 11.10 11.10 11.09 11.09 11.09 mA 525 550 575 600 625 650 675 700 725 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 12000 SD Volts 11.08 11.08 11.08 11.08 11.07 11.07 11.07 11.06 11.06 11.03 10.90 10.78 10.65 10.53 10.40 10.28 10.15 10.03 9.90 9.65 Specifications: This monitor will disconnect as much as it can and then put itself in sleep mode. It will still draw about 4mA of current. Cycle the BATTERY switch to bring the unit ON. The unit will require recharging. This mode is a fail safe should it not be swtiched off when stored, however, it is always best to disconect all power by putting the BATTERY switch OFF when storing. If the batteries are driven down to a low voltage, it may be difficult to recover them. If the battery charger "sees" the battery voltage as being low, it will attempt to recharge them with about 200mA. If the battery voltage fails to recover to over 11 volts within about 30 minutes, the charger will reset and try again. Severely discharged batteries may be able to be recovered by the system cycling thought this automatic process. It is best not to let the batteries run this low as it will adversely impact their life and capacity. The OTG 15W uses a high quality inverter that changes 12VDC to 120VAC. This is a complex conversion and is not achieved properly with low cost converters. Our inverter is a "Modified Sine Wave" inverter. This is as opposed to a "True Sine Wave" inverter that more closely mimics true AC power. Below is a plot of our Modified Sine Wave. It may not power all devices. It may be produce noise on sensitive electronic equipment. 9 Solar Panel Type AC Input AC Output DC Output USB Output Standby Power Battery Capacity Battery Dimensions AC Low Battery Shutdown Low Battery Shutdown AC Charging Current Solar Charging Current LED Light Dimensions Weight Indicators Fuses Internal 15 W Mono Crystalline Silicon 100-240VAC 50-60Hz fused at 2A 5X20 120VAC 60Hz 150W Modified Sine Wave 12VDC 8A Unregulated PTC Fused 5V 500mA Regulated Current Limited 20mA Nominal, 4mA Protect Mode 2 X 12VDC 9AHr SLA F2 Terminals 151L x 65D x 94H mm ~10.5V 11.5V to 10V Depending on Load ~2 Amp ~750mA Full Sunlight 3W High Brightness 490W x 90D x 320H mm ~21.5 Lbs On/Standby LED, 2x8 Character LCD Panel 16A 5X20 Spare Included on Board or Storage Temp. Operating Temp. -15 to 40ºC Charge 0 to 40ºC, Discharge 15º to 50ºC External 20A Resetable Breaker LINOR ONE (1) YEAR LIMITED WARRANTY LINOR’s warranty obligations for this hardware product are limited to the terms set forth below: LINOR TECHNOLOGY, INC. (“LINOR”) warrants this product against defects in materials and workmanship under normal use for a period of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser (“Warranty Period”). A copy of a retail receipt is required as proof of purchase. If a hardware defect arises and a valid claim is received within the Warranty Period, at its option and to the extent permitted by law, LINOR will either (1) repair the hardware defect at no charge, using new or refurbished replacement parts, (2) exchange the product with a product that is new or which has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product, or (3) refund the purchase price of the product. When a refund is given, the product for which the refund is provided must be returned to LINOR and becomes LINOR’s property. The foregoing warranty is subject to Buyer’s (i) promptly written claim and (ii) timely provision to LINOR of an opportunity to inspect and test the Product claimed to be defective. Such inspection may be on Buyer’s premises and/or LINOR may request the return of the Product at Buyer’s expense. However, LINOR shall not be responsible for packing, inspection, or labor costs in connection with the return of Product. No Product shall be accepted for warranty service that is not accompanied by a Return Merchandise Authorization number (RMA#) issued by LINOR. EXCLUSIONS AND LIMITATIONS Software distributed by LINOR with or without the LINOR brand name (including, but not limited to system software) is not covered under this Limited Warranty. LINOR does not warrant that the operation of the product will be uninterrupted or error-free. LINOR is not responsible for damage arising from failure to follow instructions relating to the product’s use. To assure conformance with operating limitations, Buyer should refer to the applicable data sheet and instruction book. Batteries are not included in the Warranty. LINOR MAKES NO OTHER OR FURTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR WARRANTY OF MERCHANTABILITY. IN NO EVENT SHALL LINOR BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF ANTICIPATED PROFIT, OR OTHER ECONOMIC LOSS OR FOR ANY DAMAGES ARISING IN TORT WHETHER BY REASON OF STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE REGARDLESS OF WHETHER IT HAS BEEN APPRISED OF THE POSSIBILITY OF SUCH. This document and the information contained herein is provided on an "As Is" basis and Linor Technology, Inc. disclaims all warranties, express or implied, including but not limited to any warranty that the use of the information herein will not infringe any rights or any implied warranties of merchantability or fitness for a particular purpose. Linor Technology, Inc. takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Winston Salem NC 27101 firstname.lastname@example.org Data subject to change without notice. www.linortek.com 01-508-00003 B 11-12 R001V002 Printed in U.S.A.