Extractor hood - Winning Appliances

Extractor hood
[en] Instructions for installation
and use
en
Table of contents
INSTRUCTION MANUAL.......................................................... 2
s no i t c u r t s n I ] ne [
rof
8 Intended use................................................................... 2
( Important safety information ........................................ 3
7 Environmental protection ............................................. 5
Ç Operating modes ........................................................... 5
1 Operating the appliance................................................ 6
2 Cleaning and maintenance ........................................... 7
3 Trouble shooting............................................................ 8
4 Customer service .......................................................... 9
INSTALLATION INSTRUCTIONS........................................... 10
( Important safety information ...................................... 11
K General information..................................................... 12
5 Installation.................................................................... 14
INSTRUCTION MANUAL
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.bosch-home.com and in the online shop
www.bosch-eshop.com
2
no i t a l a t s n i
8Intended use
dna
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside. Do
not leave the appliance unattended during
operation. The manufacturer is not liable for
damage which is caused by improper use or
incorrect operation.
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
This appliance may be used by children over
the age of 8 years old and by persons with
reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
Children must not play with, on, or around the
appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 8 years old and are
being supervised.
Keep children below the age of 8 years old at
a safe distance from the appliance and power
cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
e s u dedne t n I
esu
Important safety information
en
(Important safety
information
: Warning
no i t amro f n i y t e f as t na t ropmI
Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
: Warning
Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the room
if the appliance is being operated in exhaust
air mode at the same time as room airdependent heat-producing appliance is being
operated.
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or
water heaters) obtain combustion air from the
room in which they are installed and discharge
the exhaust gases into the open air through an
exhaust gas system (e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from the
kitchen and neighbouring rooms - a partial
vacuum is produced if not enough fresh air is
supplied. Toxic gases from the chimney or the
extraction shaft are sucked back into the living
space.
Adequate incoming air must therefore
always be ensured.
■
An incoming/exhaust air wall box alone will
not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for combustion
is able to enter through openings that cannot
be sealed, for example in doors, windows,
incoming/exhaust air wall boxes or by other
technical means.
■
In any case, consult your responsible Master
Chimney Sweep. He is able to assess the
house's entire ventilation setup and will
suggest the suitable ventilation measures to
you.
Unrestricted operation is possible if the vapour
extractor hood is operated exclusively in the
circulating-air mode.
: Warning
Risk of fire!
■
Grease deposits in the grease filter may
catch fire.
Clean the grease filter at least every
2 months.
Never operate the appliance without the
grease filter.
Risk
of fire!deposits in the grease filter may
■
Grease
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel
(e.g. wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
Risk
of oil
fire!
■
Hot
and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk
of fire!
■
When
gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
Risk
of fire! several gas burners at the same
■
Operating
time gives rise to a great deal of heat. A
ventilation appliance installed above the
cooker may become damaged or catch fire.
Never operate two gas burners
simultaneously on the highest flame for
longer than 15 minutes. One large burner of
more than 5 kW (wok) is equivalent to the
power of two gas burners.
3
en
Important safety information
: Warning
Risk of burns!
The accessible parts become very hot when in
operation. Never touch hot parts. Keep
children at a safe distance.
: Warning
Risk of injury!
■
Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk
of injury!
■
Items
placed on the appliance may fall
down. Do not place any objects on the
appliance.
Risk
of injury!
■
The
light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1). Do not look directly into the
switched on LED lights for longer than
100 seconds.
: Warning
Risk of electric shock!
■
A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk
of electric
shock!are dangerous. Repairs
■
Incorrect
repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the aftersales service.
Risk
electric
■
Doofnot
use shock!
any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
4
Causes of damage
Caution!
Risk of damage due to corrosion. Always
switch on the appliance while cooking to avoid
condensation. Condensate can produce
corrosion damage.
Always replace faulty bulbs to prevent the
remaining bulbs from overloading.
Risk of damage due to ingress of humidity into
the electronic circuitry. Never clean operator
controls with a wet cloth.
Surface damage due to incorrect cleaning.
Clean stainless steel surfaces in the direction
of the grain only. Do not use any stainless
steel cleaners for operator controls.
Surface damage due to strong or abrasive
cleaning agents. Never use strong and
abrasive cleaning agents.
Risk of damage from returning condensate.
Install the exhaust duct in such a way that it
falls away from the appliance slightly
(1° slope).
Environmental protection
7Environmental protection
Your new appliance is particularly energy-efficient. Here
you can find tips on how to save even more energy
when using the appliance, and how to dispose of your
appliance properly.
no i t ce t orp l a t nemnor i vnE
en
ÇOperating modes
Exhaust air mode
sedom gn i t arepO
The air which is drawn in is cleaned
by the grease filters and conveyed to
the exterior by a pipe system.
Saving energy
■
■
■
■
■
■
During cooking, ensure that there is a sufficient
supply of air so that the extractor hood can work
efficiently and with a low level of operating noise.
Adjust the fan speed to the intensity of the cooking
fumes. Only use intensive mode where this is
required. A lower fan speed means that less energy
is consumed.
If there are intensive cooking fumes, select a higher
fan speed in good time. If cooking fumes have
already spread in the kitchen, the extractor hood
must be operated for longer.
Switch off the extractor hood if you no longer require
it.
Switch off the lighting if you no longer require it.
Clean and, if required, replace the filter at regular
intervals in order to increase the effectiveness of the
ventilation system and to prevent the risk of fire.
Note: The exhaust air must not be conveyed into a
functioning smoke or exhaust gas flue or into a shaft
which is used to ventilate installation rooms which
contain heat-producing appliances.
■
■
Before conveying the exhaust air into a nonfunctioning smoke or exhaust gas flue, obtain the
consent of the heating engineer responsible.
If the exhaust air is conveyed through the outer wall,
a telescopic wall box should be used.
Air recirculation
The air which is drawn in is cleaned by
the grease filters and an activated
carbon filter, and is conveyed back into
the kitchen.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
Note: To bind odours in air recirculation mode, you
must install an activated carbon filter. The different
options for operating the appliance in air recirculation
mode can be found in the brochure. Alternatively, ask
your dealer. The required accessories are available
from specialist retailers, from customer service or from
the Online Shop.
5
en
Operating the appliance
1Operating the appliance
Control panel model 3
These instructions apply to several appliance variants. It
is possible that individual features are described which
do not apply to your appliance.
ecna i l p a eh t gn i t arepO
Note: Switch on the extractor hood when you start
cooking and switch it off again several minutes after you
have finished cooking. This is the most effective way of
removing the kitchen fumes.
Control panel model 1 and 2
Explanation
<
#
Light on/off
+
Reduces the fan speed
Increases the fan speeds/intensive setting
Fan on/off
Setting the fan
Switching on
Explanation
0, A
Light on/off
1
2
3
Fan speed 1
Fan speed 2
Fan speed 3
Pull out the filter pull-out and press the # button. The
fan starts at setting 2.
Press the + or - button to change the fan strength.
Switching off
Press the # button. Slide the filter pull-out in.
Intensive setting
Setting the fan
Switching on
Pull out the filter pull-out. The fan starts at the selected
level.
Press buttons 1, 2 or 3 in order to change the fan
strength.
Switching off
Slide the filter pull-out in as far as the limit stop.
Note: When you pull out the filter pull-out again, the fan
starts up at the fan speed that was last selected.
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
Press the + button until all of the LEDs in the display
light up. The intensive setting is activated.
After approx. six minutes, the electronics automatically
reduce the fan to a lower setting . If you want to end the
intensive setting before the preset time expires, press
the - button until the required fan setting is reached.
The run time is limited. The fan is then automatically
reduced to a lower fan setting. You can switch back
manually at any time.
Fan run-on time
If you slide in the filter pull-out, the run-on time will be
activated for as long as the extractor hood is operating.
After approx. 10 minutes, the fan switches off
automatically.
Lighting
The lighting can be switched on and off independently
of the ventilation.
Press the A button.
6
Cleaning and maintenance
2Cleaning and maintenance
Area
Glass
: Warning
ecnane t n i am dna gn i nae lC
Risk of burns!
The appliance will become hot during operation,
especially near the bulbs. Allow the appliance to cool
down before cleaning.
Controls
: Warning
Risk of electric shock!
Penetrating moisture may result in an electric shock.
Clean the appliance using a damp cloth only. Before
cleaning, pull out the mains plug or switch off the circuit
breaker in the fuse box.
: Warning
Risk of electric shock!
Do not use any high-pressure cleaners or steam
cleaners, which can result in an electric shock.
: Warning
Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
Cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Do not use any of the following:
■
■
■
■
Harsh or abrasive cleaning agents,
Cleaning agents with a high alcohol content,
Hard scouring pads or cleaning sponges,
High-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Follow all instructions and warnings included with the
cleaning agents.
Area
Stainless steel
Cleaning agent
Hot soapy water:
Clean with a dish cloth and then dry with a
soft cloth.
Clean stainless steel surfaces in the grind
direction only.
Special stainless steel cleaning products are
available from our after-sales service or from
specialist retailers. Apply a very thin layer of
the cleaning product with a soft cloth.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and dry with a
soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plastic Glass cleaner:
Clean with a soft cloth.
en
Cleaning agent
Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Hot soapy water:
Clean using a damp dish cloth and dry with a
soft cloth/towel.
Risk of electric shock caused by penetrating
moisture.
Risk of damage to the electronics from penetrating moisture. Never clean operating controls with a wet cloth.
Do not use any stainless steel cleaners.
Cleaning the metal mesh grease filters
These instructions apply to several appliance variants. It
is possible that individual features are described which
do not apply to your appliance.
: Warning
Risk of fire!
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Notes
■
Do not use any aggressive, acidic or alkaline
cleaning agents.
■
When cleaning the metal mesh grease filters, also
clean the holder for the metal mesh grease filters in
the appliance using a damp cloth.
■
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
By hand:
Note: You can use a special grease solvent for
stubborn dirt. It can be ordered via the Online Shop.
■
■
■
Soak the metal mesh grease filters in a hot soapy
solution.
Clean the filters with a brush and then rinse them
thoroughly.
Leave the metal mesh grease filters to drain.
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has
no effect on the function of the metal mesh grease
filters.
■
■
Do not clean heavily soiled metal mesh grease filters
together with utensils.
Place the metal mesh grease filters loosely in the
dishwasher. The metal mesh grease filters must not
be wedged in.
7
en
Trouble shooting
Removing metal grease filter
1. Open the lock and fold down the metal grease filter.
While doing this, place your other hand under the
metal grease filter.
2. Take the metal grease filter out of the holder.
3Trouble shooting
Malfunctions often have simple explanations. Please
read the following notes before calling the after-sales
service.
gn i t o h s e l buo r T
: Warning
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Malfunction table
Problem
The appliance
does not work
Possible cause
The plug is not
plugged in.
Power cut
Faulty fuse
Notes
– Fat may accumulate in the bottom of the metal
grease filter.
– Hold the metal grease filter level to prevent
grease from dripping out.
3. Clean the metal grease filter.
On appliances with a glass plate in the filter pull-out:
■
■
The glass plate can be removed easily and can be
cleaned in the dishwasher.
To remove it, carefully lift the glass plate.
The lighting does The bulbs are
not work.
faulty.
Solution
Connect the appliance to the
electricity supply
Check whether other kitchen
appliances are working
Check in the fuse box to make
sure that the fuse for the
appliance is OK
For information on changing
the bulbs, see the "Replacing
Bulbs" section.
--------
Replacing bulbs
These instructions apply to several appliance variants. It
is possible that individual features are described which
do not apply to your appliance.
: Warning
Risk of burns!
Halogen bulbs become very hot when switched on.
There is still a risk of burning for some time after they
have been switched off. Allow the halogen bulbs to cool
down before replacing them.
: Warning
Risk of electric shock!
When changing the bulbs, the bulb socket contacts are
live. Before changing the bulb, unplug the appliance
from the mains or switch off the circuit breaker in the
fuse box.
Important! Only use bulbs of the same type and
wattage.
Installing the metal mesh grease filter
1. Insert the metal mesh grease filter.
While doing this, place the other hand under the
metal mesh grease filter.
2. Fold the metal mesh grease filter upwards, locking it
in place.
8
Customer service en
Replacing halogen bulbs
Note: When inserting halogen bulbs, do not touch the
glass tube. Use a clean cloth to insert the halogen
bulbs.
1. Carefully remove the bulb ring using a suitable tool.
2. Pull out the bulb and replace it with a bulb of the
same type.
4Customer service
When calling us, please give the product number
(E no.) and the production number (FD no.) so that we
can provide you with the correct advice. The rating plate
with these numbers can be found inside the appliance
(remove the metal mesh grease filter to gain access).
You can make a note of the numbers of your appliance
and the telephone number of the after-sales service in
the space below to save time should it be required.
ec i v res remo t suC
E no.
3. Insert the bulb cover.
4. Insert the mains plug or switch on the fuse again.
LED lights
Defective LED lights may be replaced by the
manufacturer, their customer service or a qualified
technician (electrician) only.
: Warning
Risk of injury!
The light emitted by LED lights is very dazzling, and can
damage the eyes (risk group 1). Do not look directly
into the switched on LED lights for longer than
100 seconds.
FD no.
After-sales serviceO
Please be aware that a visit by an after-sales engineer
will be charged if a problem turns out to be the result of
operator error, even during the warranty period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
GB
0344 892 8979
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 €
per minute.
Rely on the professionalism of the manufacturer. You
can therefore be sure that the repair is carried out by
trained service technicians who carry original spare
parts for your appliances.
Accessories
(not included in the scope of delivery)
Note: These instructions apply to several appliance
models. It may be the case that an optional accessory
that is listed does not apply for your appliance.
Note: Observe the installation instructions in the
accessory.
Accessories
Basic equipment:
Starter set for circulating-air mode
Throw-away filter for starter set
Basic equipment:
CleanAir air recirculation module
Throw-away filter for CleanAir recirculation module
Handle strip: 60 cm:
Stainless steel
White
Black
Handle strip: 90 cm:
Stainless steel
White
Black
Order number
DSZ4545
DSZ4551
DSZ4680
DSZ4681
DSZ4655
DSZ4652
DSZ4656
DSZ4955
DSZ4952
DSZ4956
--------
9
Customer service
en
INSTALLATION INSTRUCTIONS
Installation instructions
These instructions apply to several appliance variants. It
is possible that individual features are described which
do not apply to your appliance.
■
■
■
Appliance width 60 cm:
This appliance is installed in a upper cabinet.
Follow the enclosed installation instructions for
additional special accessories (e.g. for circulating-air
mode).
The surfaces of the appliance are sensitive. Avoid
damaging them during installation.
[
Appliance width, 90 cm:
[
10
Important safety information
(Important safety
information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
The width of the extractor hood must
correspond at least with the width of the hob.
For the installation, observe the currently valid
building regulations and the regulations of the
local electricity and gas suppliers.
When conveying the exhaust air, official and
legal regulations (e.g. state building
regulations) must be followed.
no i t amro f n i y t e f as t na t ropmI
: Warning
Risk of death!
Risk of poisoning from flue gases that are
drawn back in. The exhaust air must not be
conveyed into a functioning smoke or exhaust
gas flue or into a shaft which is used to
ventilate installation rooms that contain
heating appliances. If the exhaust air is to be
conveyed into a non-functioning smoke or
exhaust gas flue, you must obtain the consent
of the heating engineer responsible.
: Warning
Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the room
if the appliance is being operated in exhaust
air mode at the same time as room airdependent heat-producing appliance is being
operated.
en
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or
water heaters) obtain combustion air from the
room in which they are installed and discharge
the exhaust gases into the open air through an
exhaust gas system (e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from the
kitchen and neighbouring rooms - a partial
vacuum is produced if not enough fresh air is
supplied. Toxic gases from the chimney or the
extraction shaft are sucked back into the living
space.
Adequate incoming air must therefore
always be ensured.
■
An incoming/exhaust air wall box alone will
not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for combustion
is able to enter through openings that cannot
be sealed, for example in doors, windows,
incoming/exhaust air wall boxes or by other
technical means.
■
In any case, consult your responsible Master
Chimney Sweep. He is able to assess the
house's entire ventilation setup and will
suggest the suitable ventilation measures to
you.
Unrestricted operation is possible if the vapour
extractor hood is operated exclusively in the
circulating-air mode.
: Warning
Danger of death!
Risk of poisoning from flue gases that are
drawn back in. If installing a ventilation system
in a room with a heat-producing appliance
connected to a chimney/flue, the electricity
supply to the hood must be equipped with a
suitable safety switch.
11
en
General information
: Warning
Risk of fire!
Grease deposits in the grease filter may catch
fire. The specified safety distances must be
observed in order to prevent an accumulation
of heat. Observe the specifications for your
cooking appliance. If gas and electric hobs
are operated together, the largest specified
distance applies.
Only one side of the appliance may be
installed directly next to a high-sided unit or a
wall. The distance between the appliance and
wall or high-sided unit must be at least
50 mm.
: Warning
Risk of injury!
■
Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk
of injury!
■
The
appliance may fall down if it has not
been properly fastened in place. All
fastening components must be fixed firmly
and securely.
Risk
of injury!
■
The
appliance is heavy. To move the
appliance, 2 people are required. Use only
suitable tools and equipment.
KGeneral information
Exhaust air mode
no i t amro f n i l areneG
: Warning
Risk of death!
Risk of poisoning from flue gases that are drawn back
in. The exhaust air must not be conveyed into a
functioning smoke or exhaust gas flue or into a shaft
which is used to ventilate installation rooms that contain
heating appliances. If the exhaust air is to be conveyed
into a non-functioning smoke or exhaust gas flue, you
must obtain the consent of the heating engineer
responsible.
If the exhaust air is conveyed through the outer wall, a
telescopic wall box should be used.
Exhaust duct
Note: The appliance manufacturer does not provide any
warranty for faults attributable to the pipe section.
‘
‘
: Warning
‘
‘
Risk of electric shock!
Components inside the appliance may have
sharp edges. These may damage the
connecting cable. Do not kink or pinch the
connecting cable during installation.
: Warning
Risk of electric shock!
It must always be possible to disconnect the
appliance from the electricity supply. The
appliance must only be connected to a
protective contact socket that has been
correctly installed. If the plug is no longer
accessible once the appliance has been
installed, or a fixed connection is required, the
installation must have an all-pole isolating
switch with a contact gap of at least 3 mm.
Only an electrician may install the fixed
connection. We recommend installing a
residual-current circuit breaker (RCCB) in the
appliance's power supply circuit.
: Warning
Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
12
■
■
■
The appliance achieves its optimum performance by
means of a short, straight exhaust air pipe and as
large a pipe diameter as possible.
As a result of long, rough exhaust air pipes, many
pipe bends or pipe diameters that are smaller than
150 mm, the optimum extraction performance is not
achieved and fan noise is increased.
The pipes or hoses for laying the exhaust air line
must consist of non-combustible material.
Round pipes
An inner diameter of 150 mm, but at least 120 mm, is
recommended.
Flat ducts
The inner cross-section must correspond to the
diameter of the round pipes.
150 mm diameter, approx. 177 cm2
120 mm diameter, approx. 113 cm2
■
■
Flat ducts should not have any sharp deflections.
Use sealing strips for different pipe diameters.
General information
Electrical connection
: Warning
Risk of electric shock!
Components inside the appliance may have sharp
edges. These may damage the connecting cable. Do
not kink or pinch the connecting cable during
installation.
The required connection data can be found on the
rating plate inside the appliance; to do this, remove the
metal mesh grease filter.
Length of the cable: approx. 1.30 m
This appliance complies with the EC interference
suppression regulations.
en
1. Make the cut-out for the exhaust air pipe. To do this,
make an opening in the ceiling or back wall of the
fitted unit with an additional recess for the power
cord.
PP
PP
: Warning
Risk of electric shock!
It must always be possible to disconnect the appliance
from the electricity supply. The appliance must only be
connected to a protective contact socket that has been
correctly installed. If the plug is no longer accessible
once the appliance has been installed, or a fixed
connection is required, the installation must have an allpole isolating switch with a contact gap of at least
3 mm. Only an electrician may install the fixed
connection. We recommend installing a residual-current
circuit breaker (RCCB) in the appliance's power supply
circuit.
2. If the cabinet base is present, remove this. Mark the
securing points on the inside of the cabinet and precut the holes using a piercer. Use the enclosed
template to mark the securing points. ¨
3. Screw in the four enclosed screws for the angle
bracket up to 5 mm. ©
Preparing the units
■
■
The fitted unit must be level and have sufficient loadbearing capacity.
The max. weight of the extractor hood is 18 kg.
Appliance dimensions and safety clearances
■
Observe the appliance's dimensions.
■
Comply with the safety clearances.
If the installation instructions for the gas cooking
appliances specify a different distance, the largest
distance must always be provided for.
The fitted unit must be heat-resistant up to 90 °C. The
fitted unit must still be sturdy after the cut-outs have
been made.
To install an upper cabinet, this extractor hood must be
provided with the following dimensions:
Width
Depth
Height
600 mm
Min. 320 mm
Min. 390 mm
13
Installation
en
Preparing the appliance
4. Screw the two angle brackets to the appliance.
Ensure that the screws are positioned correctly.ª
Screw in the screws until 8 mm of the threaded
section is still protruding. «
A handle strip must be screwed to the filter pull-out. This
handle strip can be one that is provided with the
appliance, or one that is available as an accessory.
1. Use the screws provided to secure the handle strip
to the filter pull-out.
[
2. Connect the power cord provided to the appliance.
¨
3. Use the strain relief to secure the power cord in
place.©
$
5Installation
Installation
no i t a l a t s n I
%
14
1. Use the angle brackets to hang the appliance on the
screws and align it.
Installation
2. Measure the distance from the appliance to the wall
and mark this on the filler strip.
3. If required, shorten the filler strip to the required
dimension.
4. Remove the appliance and screw in the filler strip.
en
Change the filter pull-out's limit stop
On some versions of the appliance, the limit stop for the
filter pull-out can be changed. Spacers are included
with these appliances in order to set the appliance's
handle strip so that it is flush with the fitted unit.
1. Pull the filter pull-out forwards.
2. Shorten the spacer to the required dimension and
insert it into the specified slot.
5. Remount the appliance, align it and screw it in place.
Carefully screw in all screws.
6. Establish the electrical connection.
Note: The extractor hood's housing can be concealed
within the upper cabinet. In doing so, you must observe
the following:
■
The intermediate floor must not be placed on the
extractor hood's housing.
■
The front panel must not be secured to the housing.
■
Access must be available in order to change the
filter and for after-sales service.
Appliance width, 90 cm:
You must also screw the appliance onto the side upper
cabinets.
Connecting the pipes
Note: If using an aluminium pipe, smooth the
connection area beforehand.
Exhaust-air pipe Ø 150 mm (recommended size)
Attach the exhaust-air pipe directly to the air-pipe
connector and seal.
Exhaust-air pipe Ø 120 mm
1. Attach the reducing connector directly to the air-pipe
connector.
2. Attach the exhaust air pipe to the reducing
connector.
3. Seal both joints appropriately.
15
Robert Bosch Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München
Germany
www.bosch-home.com
*9001057653*
9001057653
960915
Download PDF
Similar pages