AGF-10 SERIES
AC/DC Power Module 10W
FEATURES
►Fully Encapsulated Plastic Case for PCB Mounting
►Universal Input 85~264VAC, 47~440Hz
►Protection Class II as per IEC/EN 60536
►I/O Isolation 3000VAC with Reinforced Insulation
►Operating Ambient Temp. Range -25°C to +70°C
►Overload/Voltage and Short Circuit Protection
►Designed-in EMI Emission meets EN 55011/32 Class B & FCC Level B
►Designed-in EMC Immunity meets EN61000-4-2,3,4,5,6,8,11
►Eco Design, Compliant to Energy Star Specification and
ErP Directive 2009/125/EC
►UL/cUL/IEC/EN 60950-1 Safety Approval & CE Marking
PRODUCT OVERVIEW
The MINMAX AGF-10 series is a new range of fully encapsulated AC/DC power supply modules. They are designed for direct PCB mounting with solder
pins. The product features EMI-filter to EN 55011/32, class B and EMS compliance to the EN 61000-4 standard. Universal input voltage 85-264VAC and
International safety approvals qualifies these power modules for applications in products with worldwide markets.
The AGF-10 series provide a cost effective solution for many space critical applications in commercial and industrial electronic equipment.
Model Selection Guide
Model
Number
Output
Voltage
AGF-10S03
AGF-10S05
AGF-10S12
AGF-10S15
AGF-10S24
VDC
3.3
5
12
15
24
Output Current
Input Current
Max.
mA
2500
2000
833
667
417
115VAC, 60Hz
@Max. Load
mA(typ.)
171
201
191
193
201
Max. capacitive
Load
Efficiency
(typ.)
@Max. Load
%
70
72
76
75
72
uF
2200
2200
1000
1000
680
Input Specifications
Parameter
Conditions / Model
Input Voltage Range
Input Frequency Range
Input Voltage Range
No-Load Power Consumption
All Models
115VAC
230VAC
Inrush Current
Cold Start at 25℃
External Fuse (Recommended)
Min.
85
47
120
-------
All Models
Typ.
Max.
--264
--440
--370
--0.3
--15
--30
1.5A Slow – Blow Type
Unit
VAC
Hz
VDC
W
A
A
Output Specifications
Conditions / Model
Parameter
Output Voltage Setting Accuracy
Line Regulation
Load Regulation
Vin=Min. to Max.
Io=Min. to Max.
0-20 MHz Bandwidth
Ripple & Noise
Minimum Load
Over Voltage Protection
Temperature Coefficient
Overshoot
Zener diode clamp
Short Circuit Protection
E-mail:sales@minmax.com.tw
REV:15
-------
Typ.
±1.0
±0.5
±0.5
1.5
0.8
Max.
±2.0
±1.0
±1.0
1.8
1.0
Unit
%Vnom.
%
%
%VPP of Vo
%VPP of Vo
---------
10
120
±0.01
---
----±0.02
5
%Inom.
% of Vo
%/℃
% Vout
---
%Inom.
Foldback, auto-recovery
105
--(long term overload condition may cause damage)
Hiccup mode, Automatic Recovery
Over Load Protection
2017/09/15
3.3 & 5.0VDC Output Models
Other Output Models
Min.
-----
Tel:886-6-2923150
Page 1 of 3
AGF-10 SERIES
AC/DC POWER MODULE 10W
General Specifications
Parameter
I/O Isolation Voltage
I/O Isolation Resistance
Switching Frequency
Hold-up Time
MTBF (calculated)
Protection Class II
Safety Approvals
Conditions
Input to Output, 60 Seconds
500 VDC
Min.
3000
100
-----
Typ.
----125
20
300,000
Max.
---------
Unit
VACrms
MΩ
KHz
ms
Hours
Typ.
----0.375
142
67
---
Max.
+70
+85
----95
℃
℃
W/℃
℃
℃
% rel. H
---
260
℃
MIL-HDBK-217F@25℃, Ground Benign
According IEC/EN 60536
UL/cUL 60950-1 recognition(UL certificate) , IEC/EN 60950-1(CB-report)
Environmental Specifications
Parameter
Conditions
Operating Ambient Temperature Range
Storage Temperature Range
Power Derating
Min.
-25
-40
Natural Convection
+50℃ to +70℃
Shutdown, Internal IC Junction Temperature
Automatic Recovery, Internal IC Junction Temperature
Thermal Shutdown
------Natural Convection
---
Humidity (non condensing)
Cooling
Lead Temperature (1.5mm from case for 10Sec.)
Unit
EMC Specifications
Parameter
Standards & Level
Conduction and Radiation
EN 55011, EN 55024
ESD
Radiated immunity
Fast transient
Surge
Conducted immunity
PFMF
Dips
Interruptions
EMI
EMS
Performance
EN 55011, EN 55032, FCC part 15
Class B
EN 61000-4-2 air ± 8kV, Contact ± 4kV
EN 61000-4-3 10V/m
EN 61000-4-4 ±2kV
EN 61000-4-5 ±1kV
EN 61000-4-6 10Vrms
EN 61000-4-8 30A/m
EN 61000-4-11 30% 10ms
EN 61000-4-11 >95% 5000ms
B
A
B
B
B
A
B
C
Notes
1
2
3
4
5
6
Specifications typical at Ta=+25℃, resistive load, 115VAC, 60Hz input voltage and after warm-up time rated output current unless otherwise noted.
We recommend to protect the converter by a slow blow fuse in the input supply line.
These power modules require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage the power
supplies however they may not meet all listed specifications.
Other input and output voltage may be available, please contact factory.
That “natural convection” is about 20LFM but is not equal to still air (0 LFM).
Specifications are subject to change without notice.
E-mail:sales@minmax.com.tw
2017/09/15
REV:15
Tel:886-6-2923150
Page 2 of 3
AGF-10 SERIES
AC/DC POWER MODULE 10W
Package Specifications
Mechanical Dimensions
Pin Connections
23.5 [0.93]
10.0 [0.39]
10.16
[0.40]
AC(N) – AC Neutral
2
AC(L) – AC Line
3
+Vout
4
-Vout
5.0 [0.20]
Bottom View
Function
1
52.4 [2.06]
1.0 [ 0.04]
3
45.72 [1.80]
4
0.7 [0.03]
Pin
2
1
►All dimensions in mm (inches)
►Tolerance: ±0.5 (±0.02)
20.32 [0.80]
►Pin diameter  1.0 ±0.1 (0.04±0.004)
27.2 [1.07]
Physical Characteristics
Case Size
:
52.4x27.2x23.5mm (2.06x1.07x0.93 Inches)
Case Material
:
Plastic resin (flammability to UL 94V-0 rated)
Weight
:
54g
Minmax Technology Co., Ltd.
18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan
Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: sales@minmax.com.tw
2017/09/15
REV:15
Page 3 of 3
Download PDF
Similar pages