with
BACK BOX
TECHNOLOGY
TECHNOLOGY
Solid State LED
Installation Instructions
TOOLS
NEEDED:
1/8” Allen wrench
Phillips Screwdriver
Waterproof Wire connectors
Warning
Low Voltage
Hot Surface
By Others
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
•
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield. SAVE THESE INSTRUCTIONS
Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
•
Follow product label information and instructions.
•
Qualified Personnel must perform all servicing or relamping of
this product.
•
Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
•
The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
•
Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
•
Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
•
Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
•
Replace lamp only with correct wattage and type of lamp
marked on fixture label.
•
All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
IMPORTANT LISTINGS AND CERTIFICATIONS
· Suitable for wet location · Additionally suitable for mounting within 4 ft. of the ground • Type Non-IC
Please refer to the low voltage design guide at www.bklighting.com/lvguide before installation for proper wire selection.
LED and Heatsink
Assembly
Driver
BQ
This set of instructions works for:
BQ
BQL
SQ
SQL
VQ
VQL
-
Brick Star™
Louvered Brick Star™
Square Step Star™
Louvered Square Step Star™
Square Versa Star™
Louvered Square Versa Star™
BQ
Faceplate
Rectangular Junction Box
(MB2) with Extension
BQL
SQ
Adjustable Aiming
Bracket
SQL
IMPORTANT NOTE
VQ and VQL mount in ceiling.
Orientation of installed back
box determines faceplate screw
orientation.
VQ
VQL
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
B-K LIGHTING
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • info@bklighting.com
RELEASE DATE
5-18-16
REFERENCE NUMBER
INS001003
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
with
BACK BOX
TECHNOLOGY
TECHNOLOGY
Solid State LED
Installation Instructions
Phase 1 - Rough In
Installation of Back box
Additional Info
•
•
•
•
•
1. Remove canopy and/or fixture from MB2
housing. Ensure unused tapped holes are
plugged to maintain seal. Plugs are provided.
2. Install Conduit (By Others) to be used with
this product.
NOTE: Surface conduit is a common entrance
for water if not properly sealed. Seal
connector threads and conduit with a suitable
sealant (Teflon tape, adhesive, etc.). Sealing
the conduit after knockouts are removed is
required to maintain warranty.
Please follow National and Local electrical codes for your area.
Suitable for through wire.
Suitable for installation into combustible materials.
Rated for 90° C.
Orientation of installed back box determines faceplate screw
orientation.
3. To prepare MB2 for mounting, align
mounting brackets on back of box. Brackets
can be aligned to vertical, horizontal or 45°
orientation. Secure with mounting screw
using screwdriver.
Install back box so that front face is flush
with finished wall or ceiling. Make sure
rectangular back box is plumb before
proceeding.
4. Mount MB2 box to surface using mounting
hardware (Provided) using the mounting
brackets attached to back of MB2 box.
Alternative mounting methods may
compromise integrity of MB2 against water
intrusion and will void warranty.
5. Connect box to conduit and pull wires for
connections (See Wiring diagram).
Phase 2 - Finish Installation of Fixture with Remote Transformer
LINE
Remote
Transformer
12V
Fixture
COM
COM
WIRING DIAGRAM
remote
LED - For use with 12VAC
transformer or magnetic transformers only. B-K
Lighting cannot guarantee performance with
third party manufacturers’ transformers.
­2. To aim, loosen the two (2) Phillips screws
attaching the adjustable bracket to the
faceplate. Aim to desired position. Tighten two
(2) Phillips screws to lock in place when desired
angle is set.
3. Mount faceplate using two (2) #10-24 screws with
1/8” Allen wrench. Tighten evenly to compress
gasket. Do not over tighten.
1. Make watertight connections from remote
transformer to LED leads using waterproof wire
connectors. (By Others) See wiring diagram.
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
B-K LIGHTING
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • info@bklighting.com
RELEASE DATE
5-18-16
REFERENCE NUMBER
INS001003
Download PDF
Similar pages