Important Battery lnformation
Instructions for M-888
Series Digital Game Cameras
- Only use Alkaline or Lithium batteries. We recommend the use of Energizer batteries.
- Do not mix old and new batteries. Always replace ALL the batteries at the same time.
- When the camera is not in use, please remove the batteries.
Moultrie Limited Warranty
This product has been thoroughly tested and inspected before shipment. It is guaranteed from
defects in material and workmanship from the date of purchase for 2 years. Under this limited
guarantee we agree to replace or repair free of charge any part or parts which have been found to
be defective in original material or workmanship. Should you require in-warranty service, call our
Customer Service Department. If your problem cannot be addressed over the telephone, we may
need you to send us your defective product plus proof of purchase.
You must register your camera at www.moultriefeeders.com/warranty to activate
your 2-year warranty.
THANK YOU for your purchase of an M-888 Series Digital Game Camera. Please
read this booklet before using the unit. If you should have any questions about this product
or any other Moultrie product, please contact us using the information on the back of
this booklet. Please register your camera at www.moultriefeeders.com/warranty
to activate your warranty.
A
CAMERA OVERVIEW
FRONT VIEW
Troubleshooting
Please visit www.moultriefeeders.com/contact-us for troubleshooting and helpful tips.
Infrared LED Flash
Motion Sensor
Returns and Repairs
Please visit http://www.moultriefeeders.com/return-policy and complete the form or our
Service Department will gladly answer any questions you have. Call 800-653-3334,
Monday - Friday, 8:00 AM to 5:00 PM CST.
LCD Display
FCC Statements
Moultrie Products
MCG-13067
M-888
Camera Lens
SD Card Slot
Moultrie Products
MCG-13068
Status Indicator
M-888i
Note: changes and modifications not expressly approved by the party responsible could void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Reorient or relocate the receiving antenna.
- lncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
OK/Select Button
Navigation Buttons
Push Button Release for battery compartment
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE: This device complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Menu Button
QUICK START
CUSTOM START
AIM
OFF
BOTTOM VIEW
External Power Port
USB Port
Battery Tray
www.moultriefeeders.com
PRADCO Outdoor Brands • 3280 Highway 31, Ste B • Calera, AL 35040
11232015 / MCG-13067 • MCG-13068
1/4” 20 Mount
M-888 Series Digital Game Camera
Page 1
MOULTRIE M-888 SERIES
M
MOULTRIE ACCESSORIES (Sold Separately)
Moultrie Mobile® Compatibility
R ES ET
OP TIONS
RESET
O PTI O N S
PHO TO OR
VI DEO
MULT I-SHOT
PIR
SE NSIT IVIT Y
T. L. PRO GRA M # 2
STO P TI ME
T. L. PRO GRAM #2
STA RT TI ME
T .L. PROGRAM #1
ST OP T IME
T .L. PROGRAM #1
ST ART T IME
*If Timelapse Program #1 is set to Always On,
settings for Program #2 will be disabled.
Your camera is compatible with our Moultrie Mobile®
DE T E CT ION
STA R T M OTION
DETEC T
cellular
service whenMOTION
combined
with the DETEC
DE LAY
T C A P TU R E
M A IN SC R EEN
Field Modem MV1.
Please
visit www.moultriemobile.com
TIM E L A P SE
T IME LAPSE
E RVAL information.M A IN SC R EEN
forINTmore
STA R T TIM E
L A P SE C A P TU R E
STA R T M OTION +
M OTION
+ T.L . may be required
update
T.L . C A P TU R E
M A IN SC R EEN
firmware
*SetNOTE:
options in theCamera
respective menus.
for full Moultrie Mobile functionality.
INFOST RIP
ACT IVE
T E MPE RAT URE
(ºF OR ºC)
INFOSTR IP
OP TIONS
DA TE & TIM E
C A M ER A NA M E
Using the Moultrie AC Adapter
VIDE O QUALIT Y
UPGRADE
FIRMWARE
DEFAULT SETTINGS
SY STEM
Note:
FACT
ORYLeave
RE SE T internal batteries in the camera during
A C C ONNEC TED
OP TIONS
use. In the event of power loss to the outlet into which
the AC adapter is plugged, the internal batteries will
keep your camera running.
M OTION FR EEZE
M A NA G ED M EM OR Y
P R OG R A M
SEC U R ITY C ODE
C ONFIR M
SEC U R ITY C ODE
Using the Moultrie Camera Power Panel
General
Page 2
PH OTO/V IDEO
Keep
your
with
VIDE O LE
NGT HMoultrie camera running in the field
P H OTO
QU A L ITY
OP TIONS
the constant power of an AC adapter. Plug into a
standard 110-240VAC 50-60Hz electrical outlet and
M EM ORPower
Y
then connect to the External
Port onERyour
A SE A L L IM A G ES
OP TIONS
Moultrie camera.
DATE/TIME:
01/01/2016 11:11pm
PHOTO QUALITY:
MED (4 MP)
VIDEO QUALITY:
HD (1280 x 720)
VIDEO LENGTH:
10 SECONDS
MOTION FREEZE:
ON (FAST FLASH)
CAMERA NAME:
MOULTRIECAM
INFOSTRIP ACTIVE:
YES
TEMPERATURE:
FAHRENHEIT
AC CONNECTED?:
NO
PROGRAM SECURITY CODE:
00000
MANAGED MEMORY:
DO NOT OVERWRITE
ERASE ALL IMAGES:
NO
FACTORY RESET:
NO
M-888 Series Digital Game Camera
Place near the tree where the camera is mounted.
Place for best exposure to sun. To attach to a
tripod secure the power panel to the tripod
angled upward for best exposure. Plug the power
panel to the Power Panel Plug. This will extend the
life of your camera in the field.
Note: Leave internal batteries in the camera
during use. The Camera Power Panel needs
4 hours of sunlight to fully power the camera.
Using the Moultrie Battery Box
Extend the field life of your Moultrie camera with a
long-lasting, rechargeable external power source.
Place near the tree where the camera is mounted.
Plug the Battery Box to the Power Panel Plug.
This will extend the life of your camera in the field.
M-888 Series Digital Game Camera
Page 15
L
MENU MAP
VIEWING YOUR IMAGES
There are a number of ways for you download and view
the pictures, videos in the field or at another location.
RESET
PHO TO OR
O PTI O N S
VI DEO
Removing the SD Card
To remove the SD Memory Card, open the camera cover
and push gently on the
SD card andT. L.it PRO
willGRA
pop
out slightly
R ES ET
T. L. PRO GRAM #2
M #2
allowing you to remove
it. Load the SD
OP TIONS
STA RT TI ME
STOcard
P TI MEinto the
player or card reader to view or move stored images to
*If Timelapse Program #1 is set to Always On,
another location.
settings for Program #2 will be disabled.
MULT I-SHOT
PIR
SE NSIT IVIT Y
DE T E CT ION
DE LAY
MOTION DETEC T
M A IN SC R EEN
STA R T M OTION
DETEC T C A P TU R E
T .L. PROGRAM #1
ST OP T IME
T .L. PROGRAM #1
ST ART T IME
T IME LAPSE
INT E RVAL
TIM E L A P SE
M A IN SC R EEN
STA R T TIM E
L A P SE C A P TU R E
M OTION + T.L .
M A IN SC R EEN
STA R T M OTION +
T.L . C A P TU R E
INFOSTR IP
OP TIONS
DA TE & TIM E
PH OTO/V IDEO
OP TIONS
P H OTO QU A L ITY
M OTION FR EEZE
M EM OR Y
OP TIONS
ER A SE A L L IM A G ES
M A NA G ED M EM OR Y
SY STEM
OP TIONS
A C C ONNEC TED
P R OG R A M
SEC U R ITY C ODE
*Set options in the respective menus.
Important
Make sure that the camera is in the OFF position before
removing SD card.
ln the Field
You can download the pictures, videos, and time lapse
pictures with the aid of external devices. To download,
use an external player or card reader that is
supported by 12V DC or Mini USB Jack.
INFOST RIP
ACT IVE
VIDE O QUALIT Y
UPGRADE
FIRMWARE
At Home
Remove the entire camera and transport to another location to download images. To connect the
camera to a PC computer, turn the camera ON, press the MENU button once to change to SETUP
Mode. Connect the USB cord (not included) between the USB out port and the PC computer. The
computer will recognize the camera as a removable drive. The unit works with Windows XP/Vista/7 or
Mac OS X 10.1 or higher. Copy the images and videos from the camera onto your PC for further
editing or printing. When the USB cable is disconnected, the camera will go back to SETUP mode.
T E MPE RAT URE
(ºF OR ºC)
VIDE O LE NGT H
FACT ORY RE SE T
Motion Detect
C A M ER A NA M E
C ONFIR M
SEC U R ITY C ODE
Time Lapse
RESET OPTIONS?:
DO NOT RESET
TIME LAPSE INTERVAL:
10 SECONDS
DETECTION DELAY:
10 SECONDS
TIME LAPSE PROGAMS/DAY:
2 PROGRAM
PIR SENSITIVITY:
HIGH
T.L. PROGRAM #1 START TIME:
6 AM
MULTI-SHOT:
1 (OFF)
T.L. PROGRAM #1 STOP TIME:
9 AM
PHOTO OR VIDEO:
PHOTO
T.L. PROGRAM #2 START TIME:
4 PM
T.L. PROGRAM #2 STOP TIME:
7 PM
See the full line of Moultrie camera accessories at www.moultriefeeders.com
Page 14
M-888 Series Digital Game Camera
M-888 Series Digital Game Camera
Page 3
A
CAMERA OVERVIEW (cont.)
QUICK START / CUSTOM START / AIM / OFF
Aim - When Aim is ON and the PIR Motion Sensor detects motion, the Status Indicator’s red LED on
the front of the camera will come on and remain lit as long as motion is detected.
MENU BUTTON
The Menu Button selects Camera Setup or Main Screen. When camera mode is selected, the LEFT and
RIGHT buttons navigate through the menu options. The Menu Button is also used to wake-up the
camera and turn on the display when the camera is in power saving (or sleep) mode.
OK, UP/DOWN and LEFT/RIGHT BUTTONS
The OK button selects the item to be changed. The UP/DOWN and LEFT/RIGHT buttons are used
to step through and modify the menu options. Pressing the OK button again, selects the option
indicated on the display. The OK button is also used to manually take a picture.
K
CAMERA SPECIFICATIONS
Memory & Storage
Your camera supports external SD memory cards ONLY and will accept up to a 32GB card
(Class 4 or higher). Using large memory cards can slow the camera response. The camera
cannot capture any photo or video without external memory. Please insert an SD memory card
to operate camera. Estimates are based on the most common types of memory cards that can be
purchased at electronic stores, office supply stores, or online. Estimates may vary based on camera
settings or environmental conditions.
Important
Always turn the unit off when inserting or removing an SD memory card to avoid damage and ensure
that the camera properly updates the memory information.
Photo Mode
SD Card Size:
2 GB
16 GB
MAX ZOOM 4992 x 2808
1300
10400
HIGH 3840 x 2160
1800
15200
BATTERY COMPARTMENT
MED 2688 x 1512
3800
30400
The camera is powered by eight (8) AA alkaline or lithium batteries. Push the battery compartment
release button to eject the battery tray. Install batteries as indicated on the engravings on the battery
tray, taking care to note the correct polarity.
LOW 1920 x 1080
7500
60000
SD Card Size:
2 GB
16 GB
HD 1280 x 720 (based on 10 sec video)
110
880
VGA 640 x 480 (based on 10 sec video)
310
2480
See Important Battery Information section on the back page of this manual.
SD CARD SLOT
Accepts up to a 32GB SD Card (Class 4 or higher) for photo and video storage.
NOTE: A Class 4 or higher SD Card must be installed for the camera to operate (sold separately).
USB PORT
Actual capacity will vary based on image properties.
Specifications
Download still pictures and video onto your computer by connecting a micro-B to USB cable
(not included) to the USB port.
EXTERNAL POWER PORT
Accepts the Moultrie PowerPanel, Moultrie AC Adapter or Moultrie Battery Box accessories
(sold separately) only. Refer to www.moultriefeeders.com for more information.
NOTE: The use of any other power source will void your warranty and possibly harm your camera.
Page 4
Video Mode
M-888 Series Digital Game Camera
Operational Mode
Motion Detect / Time Lapse / Motion + Time Lapse
Resolution
14.0 MP
Still Resolutions
JPEG
Low 1920 x 1080, Med 2688 x 1512,
High 3840 x 2160, Max Zoom 4992 x 2808
Video Resolutions
VGA- 640 x 480, HD 1280 x 720
SD Memory Card
Up to 32 GB SD card, Class 4 or higher (not included)
Format
JPEG - Still pictures, AVI - Video clips
Power Supply
8 AA Alkaline or Lithium batteries (not included)
M-888 Series Digital Game Camera
Page 13
J
SYSTEM OPTIONS (cont.)
CONFIRM
SECURITY
CODE00000
Confirm Security Code
Once a Security Code has been entered, the camera will prompt you to verify the code. This will keep
you from mis-entering a code or seting a code inadvertantly.
B
QUICK START INSTRUCTIONS
Use the steps below as a guide to quickly set up your camera so it will function using the factory
default settings.
STEP 1
Open camera cover. Press the battery chamber release button. Install eight (8) AA size alkaline or
lithium batteries with polarities as indicated in the Battery Tray. Re-install the Battery Tray and insert
your SD card. We recommend that you erase the SD card (ERASE IMAGES) inside the camera before
taking pictures: this will not only erase all images, but will also format your SD card for use in the camera.
STEP 2
FACTORY
RESET?
NO
Reset to Default settings
You can reset your camera to the factory default settings. Press UP or DOWN to choose YES - all
setups restored to factory default or NO - keep custom settings. Press the OK button again to
make selection. Press the Right button to go to the Main Screen.
UPGRADE
FIRMWARE
4M880-130903
NO
Upgrade Firmware
The firmware version is displayed. Press Up/Down to choose setting.
YES - To upgrade firmware.
NO - Keep current firmware.
Insert SD Memory Card until you hear an audible click. Camera will not operate without SD Card.
Slide the power switch to Quick Start. Press the Left button to set the time and date.
STEP 3
Eyelet
Mount camera in desired location using a mounting
strap. NOTE: Camera must be attached to a stable
object for motion detection to function properly.
Mounting camera on an unstable structure may
result in excess image captures with no subject
(false triggers).
STEP 4
Switch camera to Aim. Aim camera using motion
detection to determine target area. Walk in front of the
camera at the desired distance and the camera LED will flash
showing the covered area. Switch camera to Quick Start.
Mounting
Strap
STEP 5
NOTE: This operation should only be performed when prompted by a technician to do so.
Close cover. The camera will operate using Default settings. You may also customize the settings if
desired in Custom Start.
Setting Run Mode
When you choose Quick Start, the only settings that
you will be able to change will be Date and Time, allowing
for rapid setup. Other settings are:
Page 12
M-888 Series Digital Game Camera
OPTION
SETTING
Mode
Motion Detect
Detection Delay
30 seconds
Multi-Shot
3-Triggered
Photo or Video
Photo
M-888 Series Digital Game Camera
Page 5
C
I
CAPTURE MODES
Setting Capture Mode
Use the Up/Down buttons to choose between operating modes. This camera has 3 modes.
MANAGED
DO
1. Motion Detect - Capture photo or video when
motion or heat is detected.
2. Time Lapse - Capture photo at periodic intervals
based on the Time Lapse program setting.
3. Motion + Time Lapse - Uses a combination of
Time Lapse and Motion Detect modes at different
times of the day. Press the Right button to move to
start motion capture.
MOTION
DETECT
<OPTIONSSTART>
TIMELAPSE
<OPTIONSSTART>
MOTION+T.L.
<OPTIONSSTART>
NOTE: Options for Motion and Time Lapse
can be set in their respective option menus.
D
SETTING MOTION DETECT OPTIONS
MOTION
DETECT
<OPTIONSSTART>
Setup Selection Setting
From the Default Screen, pressing the Menu button will enter the current capture mode’s Main
Screen. Press the Down button 3 times to enter GENERAL SETTINGS. Press the Left button to move to
the next setting. Using this method you can customize your camera’s feature settings.
From this Main Screen, press OK to get to the Test Capture screen.
MEMORY OPTIONS
NOT
Managed Memory
Selecting the OVERWRITE OLDEST option will cause the oldest files to be overwritten with new
captures when the SD card reaches its capacity. With the DO NOT OVERWRITE option selected, the
camera will cease image capture once the SD card reaches capacity. Press the OK button to select.
When your selection has been made, press Right button to go to the next option.
ERASE
ALL
10
DELAY
SECONDS
Event Delay Setting
Detection Delay determines the number of minutes between pictures when an animal is detected and
remains in range. Press the OK button. Use the Up/Down buttons to choose between (0 sec, 10 sec,
30 sec, 1 min, 5min, 10min, or 30 min). Press OK to lock in your selection, then press Left button to go
to the next option.
Page 6
M-888 Series Digital Game Camera
IMAGES
NO
Erase Images
Press the OK button. Use the Up/Down buttons to choose between Yes - erase all images, or
No - does not change stored images. Press the OK button to select. When your selections has been
made, press the Right button to move to the next option.
NOTE: This will also format your SD card for use in your camera.
J
AC
SYSTEM OPTIONS
CONNECTED?
NO
AC Connected
Press the OK button. When the camera is connected to an AC power supply and this option is
selected, the camera will remain on instead of going to a sleep state between detection and capture
sequences. This will greatly improve camera speed and performance and can be used in conjunction
with most external supplies, but is only recommended when connected to an AC power supply.
In the event this option is selected but no external supply is detected, it will default to the NO state.
Press the OK button to confirm the selection. Press the Right button to move to the next option.
PROGRAM
DETECTION
MEMORY
OVERWRITE
SECURITY
CODE00000
Security Code
Press the OK button. Use the Up/Down and Left/Right buttons to select a 5 digit security code
for your camera. Press the OK button to confirm the selection. Press the Right button to move to the
next option.
NOTE: Please remember your security code. If the code is lost, you can contact Moultrie customer
support to reset the password (charges may apply). Also, use caution when navigating through
the Security Code option as not to set a code by mistake. For no Security Code, the setting should
remain as “00000”.
M-888 Series Digital Game Camera
Page 11
H
SETTING PHOTO/VIDEO OPTIONS
PHOTO
QUALITY
MED(4MP)
Setting Photo Quality
Press the OK button. Use the Up/Down buttons to choose between 4 image resolution settings.
1. Max Zoom:
4992 x 2808
2. High:
3840 x 2160
3. Medium:
2688 x 1512
4. Low:
1920 x 1080
Press the OK button to confirm the selection. Press the Right button to move to the next option.
MOTION
ON
FREEZE
(FAST
FLASH)
Setting Motion Freeze
This feature maximizes the image clarity during night photos. When this feature is on the camera
will adjust the exposure time to reduce blur associated with motion. Other adjustments are made to
increase the brightness and clarity of the photo. When this feature is turned off the camera will use a
maximum exposure time that will not reduce blur, but will increase the effective flash range and image
brightness of night photos. Press the OK button to confirm the selection. Press the Right button to
move to the next option.
VIDEO
QUALITY
HD
(1280X720)
Setting Video Quality
Press the OK button. Use the Up/Down buttons to choose between 2 image quality settings.
1. HD:
1280 x 720
2. VGA:
640 x 480
Press the OK button to confirm the selection. Press the Right button to move to the next option.
VIDEO
LENGTH
10
SECONDS
Setting Video Length
Press the OK button. Use the Up/Down buttons to choose between 5 video length settings
(5, 10, 30, 60 or 90 seconds). Press the OK button to confirm the selection. Press the Right button to
move to the next option. NOTE: Night videos are limited to a maximum of 30 seconds.
Page 10
M-888 Series Digital Game Camera
D
SETTING MOTION DETECT OPTIONS (cont)
PIR
SENSITIVITY
HIGH
PIR Sensitivity
PIR Sensitivity allows you to control as to how much movement and at what distance the camera
will trigger. HIGH sensitivity will allow for more distance, but will make the camera slightly more
susceptible to false triggers and is ideal for open areas such as fields and food plots. LOW sensitivity
will shorten the distance but lower the chance of false triggers and is ideal for close range traps and
deeply wooded areas. Press the OK button. Use the Up/Down buttons to choose between
(HIGH or LOW). Press OK to lock in your selection, then press Left button to go to the next option.
MULTI-SHOT
1 (OFF)
Setting Multi-Shot
Press the OK button. Use the Up/Down buttons to choose between settings. Choose how many
pictures you would like captured in a sequence when the camera is triggered (1 or 3).
Available options are:
1 (OFF) - Single photo taken per event.
3 BURST - Three rapidly captured photos taken per event. All 3 photos are captured within one second.
NOTE: Burst mode is only capable of up to 4MP captures, regardless of your resolution setting.
3 TRIGGERED - Up to three photos are captured per event with an approximate one second delay
between each capture. Each subsequent photo after the first requires an individual trigger. This
allows for multiple potential image captures of the same event while reducing the chance of empty
images if the subject moves out of the field of view after the first shot.
Press OK to lock in your selection, then press Left button to go to the next option.
PHOTO
OR
VIDEO
PHOTO
Setting Photo or Video
Press the OK button. Use the Up/Down buttons to choose between Photo, Video or Both. Press the
OK button. Press Left button to go to the Main Screen.
RESET
OPTIONS?
DO
NOT
RESET
Reset Options
Press the OK button. Use the Up/Down buttons to choose between a set of predefined configurations
for the motion detect capture mode to quickly configure your camera for certain levels of performance.
Press OK to lock in your selection, then press Left button to go to the next option.
M-888 Series Digital Game Camera
Page 7
E
SETTING TIMELAPSE OPTIONS
TIMELAPSE SOFTWARE INSTALLATION
Download your free Time Lapse software at www.moultriefeeders.com/timelapsesoftware
F
SETTING MOTION + TIMELAPSE OPTIONS
Setting Motion + Timelapse Features
For PC users: Installation and operation instructions are available here, as well.
The camera operates in Time Lapse Mode during the programmed intervals and
Motion Detect Mode for the remainder of the day.
For Mac users: This software is not Mac-compatible. You can import your image files into a program
such as iMovie and create timelapse movies this way.
NOTE: The settings entered for both Timelapse and Motion Detect modes
will be used when in this mode. Settings can be made in their respective menus.
TIMELAPSE
INTERVAL
10
SEC
Interval Time Setting
Press the OK button. Use the Up/Down buttons to choose between 10, 30 seconds / 1, 5, 10, 15, or
30 minutes / 1, 2, 3, 6, 12 hours or 1 day. When your selection has been made, press the Left button
to go to the next option.
T.L.
PROGRAM
#1
START6AM
Setting Program Wake up
Press the OK button. Use the Up/Down buttons to choose between 24 different settings: any hour
from MlDNlGHT to 11 PM. This will determine what time the camera will wake up during the program
and begin its time lapse program. Setting to ALWAYS ON will make the camera operate in timelapse
24 hours/day. Press Left button to go to the next option.
G
SETTING INFOSTRIP OPTIONS
INFOSTRIP
ACTIVE
YES
Infostrip Active
Use the Up/Down buttons to choose between:
YES - Camera Name, Time, etc, information will be imprinted at the bottom of the image/video
as an information bar
Note: Remember to input the camera name in the setup and set the clock accordingly.
NO - No information bar will be imprinted.
Press the OK button to confirm the selection. Press the Right button to move to the next option.
TEMPERATURE
FAHRENHEIT
T.L.
PROGRAM
#1
STOP10AM
Setting Program Sleep
When wakeup time is set, the camera will automatically move to the Sleep option. Set the sleep time
after the wakeup time you already set. This will set the wake up and sleep during the time lapse
photography. Press the OK button. Press Left button to go to the next option.
Temperature
The temperature is imprinted on each photo and can be in degrees Fahrenheit or Celsius.
To change the temperature units, press the Up/Down buttons to highlight the desired setting.
Press the OK button to confirm the selection. Press the Right button to move to the next option.
DATE
&
TIME
01/01/16
11:11pm
NOTE: Repeat the above steps for each Program #2 to be set.
Press Left button to go to the Main Screen.
WARNING: If Program #1 is set to Always On, settings for Program #2 will
be disabled.
RESET
OPTIONS?
DO
NOT
RESET
Reset Options
Press the OK button. Use the Up/Down buttons to choose between to reset your Timelapse options.
Page 8
M-888 Series Digital Game Camera
Setting Date and Time
Press the OK button. Use the Left/Right buttons to move from one value to the next and the
Up/Down buttons to adjust each value. Press the OK button to lock in selections. When all your
selections have been made, and the date and time has been set, press the Right button to move to
the next option.
CAMERA
NAME
MOULTRIECAM
Setting Camera Name
Press the OK button. Use theUp/Down and Left/Right buttons to select an identity for your
camera. For example, you can use a name or a location; the identity you wish to use is up to you.
Press the OK button to confirm the selection. Press the Right button to move to the next option.
M-888 Series Digital Game Camera
Page 9