Mira
Design cordless
phone (M560)
Design cordless
phone with answering
machine (M565)
Extended user
documentation
Register your product and get support at
www.philips.com/support
Contents
1 Important safety instructions
Enter text and numbers
16
Switch between uppercase and
lowercase16
3
7Phonebook
2 Your phone
What is in the box
Overview of the phone
Overview of the base station
4
4
5
6
3 Get started
7
Connect the base station
7
Install the supplied batteries
7
Configure your phone (country
dependent)8
Change the remote access PIN
(for M565)
9
Charge the handset
9
Check the battery level
9
What is standby mode?
9
Display icons
9
Check the signal strength
10
Switch the handset on or off
11
4Calls
12
12
12
12
Make a call
Answer a call
End a call
Adjust the earpiece/speaker
volume13
Mute the microphone
13
Turn the speaker on or off
13
Make a second call
13
Answer a second call
13
Switch between two calls
13
Make a conference call with the
external callers
13
5 Intercom and conference calls 14
Make a call to another handset
Make a conference call
6 Text and numbers
14
14
16
17
View the phonebook
17
Search a record
17
Call from the phonebook
17
Access the phonebook during a
call17
Add a record
18
Edit a record
18
Delete a record
18
Delete all records
18
8 Call log
19
Call list type
19
View the call records
19
Save a call record to the
phonebook19
Return a call
20
Delete a call record
20
Delete all call records
20
9 Redial list
21
View the redial records
21
Redial a call
21
Save a call record to the
phonebook21
Delete a redial record
21
Delete all redial records
21
10Phone settings
22
22
22
23
23
23
Sound settings
Name the handset
Set the date and time
Set the display language
ECO+ mode
11 Telephone answering machine24
Turn the answering machine on
or off
24
Set the answering machine
language24
EN
1
Announcements24
Incoming messages
25
Set the ring delay
26
Remote access
26
12 Privacy mode
28
Call barring (block outgoing calls) 28
Block incoming calls
28
Change the privacy mode PIN/
passcode29
13Services
Call list type
Auto conference
Network type
Auto prefix
Select the recall duration
Dial mode
Auto clock
Register additional handsets
Unregister the handsets
Restore default settings
30
30
30
30
30
31
31
31
32
32
32
14 Technical data
33
15Notice
34
34
34
34
Declaration of conformity
Use GAP standard compliance
Compliance with EMF
Disposal of your old product
and battery
34
16 Frequently asked questions
36
17Appendix
38
38
Text and number input tables
2
EN
1Important
safety
instructions
Power requirements
• This product requires an electrical
supply of 100-240 volts AC. In case
of power failure, the communication
can be lost.
• The voltage on the network
is classified as TNV-3
(Telecommunication Network
Voltages), as defined in the
standard EN 60950.
Warning
•• Do not open the handset, base station or
••
••
••
••
••
••
••
••
charger as you could be exposed to high
voltages.
For pluggable equipment, the socket-outlet
shall be installed near the equipment and
shall be easily accessible.
Handsfree activation could suddenly increase
the volume in the earpiece to a very high level:
make sure the handset is not too close to your
ear.
This equipment is not designed to make
emergency calls when the power fails. An
alternative has to be made available to allow
emergency calls.
Do not allow the product to come into contact
with liquids.
Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives as
these may harm the set.
Do not expose the phone to excessive heat
caused by heating equipment or direct
sunlight.
Do not drop your phone or allow objects to fall
on your phone.
Active mobile phones in the vicinity may cause
interference.
•• The Electrical network is classified as
hazardous. The only way to power down the
charger is to unplug the power supply from
the electrical outlet. Ensure that the electrical
outlet is always easily accessible.
To avoid damage or malfunction
Caution
•• Use only the power supply listed in the user
instructions.
•• Use only the batteries listed in the user
instructions.
About operating and storage
temperatures
• Operate in a place where
temperature is always between
0°C to +40°C (up to 90% relative
humidity).
• Store in a place where temperature
is always between -20°C and +45°C
(up to 95% relative humidity).
• Battery life may be shorter in low
temperature conditions.
•• Risk of explosion if battery is replaced by an
incorrect type.
•• Dispose of used batteries according to the
instructions.
•• Do not dispose of batteries in fire.
•• Always use the cables provided with the
product.
•• Do not allow the charging contacts or the
••
••
••
battery to come into contact with metal
objects.
Do not let small metal objects come into
contact with the product. This can deteriorate
audio quality and damage the product.
Metallic objects may be retained if placed near
or on the handset receiver.
Do not use the product in places where there
are explosive hazards.
EN
3
2 Your phone
Congratulations on your purchase and
welcome to Philips!
To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
Line cord*
What is in the box
2 x AAA rechargeable batteries**
Guarantee
Handset**
4XLFNVWDUWJXLGH
Short user manual
Note
Base station (with two connectors)
•• * In some countries, you have to connect the
••
Charger (with one connector)**
Power adapter**
4
EN
line adapter to the line cord, then plug the line
cord to the telephone socket.
** In multi-handset packs, there are additional
handsets, chargers, power adapters and
batteries.
• Press and hold to switch the
handset on or off.
Overview of the phone
d
a
n
m
l
b
c
d
k
j
i
e
f
• Scroll down on the menu.
• Decrease the earpiece/speaker
volume.
• Access the call log in standby
mode.
e
• Press and hold to enter a pause
when making a call.
• Switch to upper/lower case
during editing.
g
f
h
o
p
q
(for M560) or / (for M565)
• Mute or unmute the
microphone.
• Access to the answer machine
menu in standby mode (for
M565 only).
• Listen to new messages from the
answering machine (for M565
only).
g Microphone
h Battery door opening
i
• Turn the speaker phone on/off.
• Make and receive calls through
the speaker.
a Earpiece
b REDIAL/C
• Delete text or digits.
• Cancel operation.
• Access the redial list.
c
• End the call.
• Exit the menu/operation.
j
• Press and hold to make an
intercom call (for multi-handset
version only).
• Set the dial mode (pulse mode
or temporary tone mode).
EN
5
k
• Press to enter a space during
text editing.
• Press and hold to lock/unlock
the keypad in standby mode.
Overview of the base
station
l
• Make and receive calls.
• Recall key (This function is
network dependent.)
m MENU/OK
• Access the main menu.
• Confirm selection.
• Enter the options menu.
• Press to access phonebook
during a call.
n
• Scroll up on the menu.
• Increase the earpiece/speaker
volume.
• Access the phonebook in
standby mode.
o Loudspeaker
p LED indicator
• Off: no new event.
• On: for two seconds when
putting the handset on the base
station.
• Flashing: new miss calls/
new messages on answering
machine, new voice mails.
• Flashing quickly: new incoming
calls.
q Handset back cover
6
EN
a
a
• Press to find handsets.
• Press and hold to enter the
registration mode.
3 Get started
Caution
•• Make sure that you have read the safety
instructions in the 'Important safety
instructions' section before you connect and
install your handset.
Connect the base station
Warning
•• Risk of product damage! Ensure that the
••
power supply voltage corresponds to the
voltage printed on the back or the underside
of the phone.
Use only the supplied power adapter to
charge the batteries.
3
Connect each end of the power
adapter to (for multi handset
version only):
• the DC input jack at the bottom
of the extra handset charger.
• the power socket on the wall.
Note
•• If you subscribe to the digital subscriber line
••
1
2
(DSL) high speed internet service through
your telephone line, ensure you install a DSL
filter between the telephone line cord and
the power socket. The filter prevents noise
and caller ID problems caused by the DSL
interference. For more information on the DSL
filters, contact your DSL service provider.
The type plate is located on the bottom of the
base station.
Connect each end of the power
adapter to:
• the DC input jack at the bottom
of the base station;
• the power socket on the wall.
Connect each end of the line cord
to:
• the telephone socket at the
bottom of the base station;
• the telephone socket on the
wall.
Install the handset
The batteries are pre-installed in the
handset. Pull the battery tape off from
the battery door before charging.
EN
7
Note
•• The country/language setting option is
country dependent. If no welcome message
is displayed, it means the country/language
setting is preset for your country. Then you can
set the date and time.
To reset the language, see the following
steps.
1
Caution
•• Risk of explosion! Keep batteries away from
••
••
heat, sunshine or fire. Never discard batteries
in fire.
Use only the supplied batteries.
Risk of decreased battery life! Never mix
different brands or types of batteries.
2
Select MENU/OK > [Phone setup] >
[Language], then press MENU/OK
to confirm.
Select a language, then press
MENU/OK to confirm.
»» The setting is saved.
Set the date and time
Note
•• Charge the batteries for 8 hours before first
••
use.
If the handset becomes warm when the
batteries are charging, it is normal.
1
2
3
Warning
•• Check the battery polarity when inserting in
the battery compartment. Incorrect polarity
may damage the product.
Configure your phone
(country dependent)
1
2
When using your phone for the first
time, you see a welcome message.
Press MENU/OK.
Set the country/language
Select your country/language, then
press MENU/OK to confirm.
»» The country/language setting is
saved.
8
EN
4
5
Press MENU/OK.
Select [Phone setup] > [Date &
time], then press MENU/OK to
confirm.
Press the numeric buttons to enter
the date, then press MENU/OK to
confirm.
»» The time setting menu is
displayed on the handset.
Press the numeric buttons to enter
the time.
• If the time is in 12-hour format,
press
/
to select [am]
or [pm] (Country dependent).
Press MENU/OK to confirm.
Change the remote
access PIN (for M565)
Note
•• The default answering machine remote
access PIN code is 0000 and it is important to
change it to ensure the security.
1
2
3
4
5
Press / or MENU/OK > [Answer
machine].
Check the battery level
Select [Remote access] > [Change
PIN], then press MENU/OK to
confirm.
The battery icon displays the current
battery level.
Enter the old PIN, then press
MENU/OK to confirm.
Enter the new PIN code, then press
MENU/OK to confirm.
Enter the new PIN code again, then
press MENU/OK to confirm.
»» The setting is saved.
Charge the handset
When the handset is off
the base station, the bars
indicate the battery level
(full, medium and low).
When the handset is on the
base station/charger, the
bars flash until charging is
complete.
The empty battery icon
flashes. The battery is low
and needs recharging.
The handset turns off if the batteries
are empty. If you are on the phone,
you hear warning tones when the
batteries are almost empty. The call gets
disconnected after the warning.
What is standby mode?
Charge your handset by docking it in
either direction. When the handset is
placed correctly on the base station,
you hear a docking tone (see 'Set the
docking tone' on page 22).
»» The handset starts charging.
Note
•• Charge the batteries for 8 hours before first
use.
•• If the handset becomes warm when the
Your phone is in standby mode when
it is idle. The handset name, date
and time, and handset number are
displayed on the standby screen.
Display icons
In standby mode, the icons shown on
the main screen tell you what features
are available on your handset.
batteries are being charged, it is normal.
Your phone is now ready to use.
EN
9
Icon
Descriptions
When the handset is off the
base station/charger, the
bars indicate the battery level
(from full to low).
When the handset is on the
base station/charger, the bars
keep scrolling until charging is
complete.
The empty battery icon
flashes and you hear an alert
tone.
The battery is low and needs
recharging.
It displays the connection
status between the handset
and base station. The more
bars are shown, the better the
signal strength is.
It remains steadily on when
browsing answered incoming
calls in the call log.
It indicates an outgoing call in
the redial list.
It flashes when there is a new
missed call or when browsing
the unread missed calls in call
log.
It remains steadily on when
browsing the read missed
calls in call log.
It flashes when receiving
incoming call.
It remains steadily on when
you are in a call.
The speaker is on.
The ringer is off.
Answering machine (M565
only): it flashes when
there is a new message or
when the memory is full. It
displays when the telephone
answering machine is turned
on.
10
EN
/
ECO+
It flashes when there is a new
voice message.
It remains steadily on when
the voice messages are
already viewed in the call log.
The icon is not shown when
there is no voice message.
It is displayed when you scroll
up / down a list or increase /
decrease the volume.
There are more digits on the
right. Press REDIAL/C to read.
The ECO+ mode is activated.
Check the signal strength
The number of bars
indicates the connection
status between the handset
and base station. The more
bars are shown, the better
the connection is.
•
•
Make sure the handset is connected
to the base station before you make
or receive calls and carry out the
phone functions and features.
If you hear warning tones when you
are on the phone, the handset is
almost out of battery or the handset
is out of range. Charge the battery
or move the handset nearer to the
base station.
Note
•• When ECO+ is on, the signal strength is not
displayed (see 'ECO+ mode' on page 23).
Switch the handset on or
off
Press and hold
on or off.
to switch the handset
EN
11
4Calls
Note
•• The talk time of your current call is displayed
on the call timer.
•• If you hear warning tones, the phone is almost
Note
•• When the power fails, the phone cannot
access emergency services.
Tip
•• Check the signal strength before you make a
call or when you are in a call (see 'Check the
signal strength' on page 10).
Make a call
You can make a call in these ways:
• Normal call.
• Predial call.
You can also make a call from the
redial list (see 'Redial a call' on page
21), phonebook list (see 'Call from the
phonebook' on page 17) and call log
(see 'Return a call' on page 20).
Normal call
1
2
Press
or
.
Dial the phone number.
• To erase a digit, press REDIAL/C.
• To enter a pause, press and hold
.
Press
or
When there is an incoming call, the
phone rings. Press or to answer the
call.
Warning
•• When the handset rings or when the
handsfree is activated, keep the handset away
from your ear to avoid ear damage.
Note
•• The caller ID service is available if you have
registered to the caller ID service with your
service provider.
•• When there is a missed call, a notification
Dial the phone number.
»» The number is dialed out.
Predial call
2
Answer a call
Tip
»» The duration of your current call
is displayed.
1
out of battery or out of range. Charge the
battery or move the phone close to the base
station.
to dial out the call.
message appears.
Turn off the ringer of the current
incoming call
When the phone rings, press REDIAL/C
to temporarily turn off the ringer of the
current incoming call.
End a call
You can end a call in these ways:
• Press
;
12
EN
• Place the handset to the base
station or charging cradle.
Answer a second call
Note
Adjust the earpiece/
speaker volume
Press
/
to adjust the volume
during a call.
»» The earpiece/speaker volume is
adjusted and the phone is back
to the call screen.
Mute the microphone
1
Press during a call.
»» The handset displays [Mute on].
»» The caller cannot hear you, but
you can still hear his voice.
2
Press again to unmute the
microphone.
»» You can now communicate with
the caller.
Turn the speaker on or off
Press
.
Make a second call
•• This service is network dependent.
When there is a periodical beep to
notify you of an incoming call, you can
answer the call in these ways:
1
2
Press and
to answer the call.
»» The first call is put on hold, and
you are now connected to the
second call.
Press and to end the current
call and answer the first call.
Switch between two calls
Note
•• This service is network dependent. Check with
your network provider for operation.
Press and .
»» The current call is put on hold,
and you are now connected to
the other.
Make a conference call
with the external callers
Note
Note
•• This service is network dependent. Check with
your network provider for operation.
1
2
Press during a call.
»» The first call is put on hold.
Dial the second number.
»» The number displayed on the
screen is dialed out.
•• This service is network and country
dependent. Check with the service provider for
operation and additional charges.
When you are connected to two calls,
press , then .
»» The two calls are combined and
a conference call is established.
EN
13
5 Intercom and
conference
calls
»» For multi-handset versions, the
handsets available for intercom
are displayed, then go to step 2.
»» For two-handset versions, the
other handset rings, then go to
step 3.
2
An intercom call is a call to another
handset that shares the same base
station. A conference call involves a
conversation between you, another
handset user and the outside callers.
Make a call to another
handset
3
Select a handset, then press MENU/
OK to confirm.
»» Wait for the other side to answer
your call.
Press on the selected handset.
»» The intercom is established.
Switch between calls
Press and hold
to switch between
the outside call and the intercom call.
Note
•• If the base station only has 2 registered
handsets, press and hold
another handset.
1
to make a call to
Press and hold .
»» For multi-handset versions, the
handsets available for intercom
are displayed, then go to step 2.
»» For two-handset versions, the
other handset rings, then go to
step 3.
2
3
4
During an external call
1
Press
EN
»» For two-handset versions, the
other handset rings, then go to
step 3.
to end the intercom call.
Press and hold .
»» The current caller is put on hold.
Press and hold
to initiate an
internal call.
»» The external caller is put on
hold.
»» For multi-handset versions, the
handsets available for intercom
are displayed, then go to step 2.
Press on the selected handset.
»» The intercom is established.
You can go from one handset to
another during a call:
14
A 3-way conference call is between
you, another handset user and the
outside callers. It requires two handsets
to share the same base station.
Select a handset, then press MENU/
OK to confirm.
»» The selected handset rings.
While you are on the phone
1
Make a conference call
2
3
Select a handset, then press MENU/
OK to confirm.
»» The selected handset rings.
Press on the selected handset.
»» The intercom is established.
4
5
Press MENU/OK.
»» You are now in a 3-way
conference call with an external
call and a selected handset.
Press
to end the conference call.
Note
•• Press
to join an ongoing conference with
another handset if [Services] > [Conference] is
set to [Auto].
During the conference call
1
2
Press and hold
to put the
external call on hold and go back to
the internal call.
»» The external call is put on hold.
Press MENU/OK to establish the
conference call again.
Note
•• If a handset hangs up during the conference
call, the other handset remains connected to
the external call.
EN
15
6 Text and
numbers
You can enter text and numbers for
handset name, phonebook records, and
other menu items.
Enter text and numbers
1
2
3
Press once or several times on
the alphanumeric key to enter the
selected character.
Press REDIAL/C to delete a
character. Press and hold REDIAL/C
to delete all characters. Press
and
to move the cursor left
and right.
Press
to add a space.
Note
•• For information on key mapping of characters
and numbers, see the chapter 'Appendix'.
Switch between
uppercase and lowercase
By default, the first letter of each word
in a sentence is uppercase and the
rest is lowercase. Press and hold
to
switch between the uppercase and
lowercase letters.
16
EN
7Phonebook
This phone has a phonebook that
stores up to 100 records. You can access
the phonebook from the base station.
Each record can have a name up to 14
characters long and a number up to 24
digits long.
You have up to 2 direct access
memories (Keys 1 and 2). Depending on
your country, keys 1 and 2 are preset to
the voice mail number and information
service number of your service provider
respectively. When you press and hold
on the key in standby mode, the saved
phone number is dialed automatically.
•
Scroll the contact list
1
2
1
2
•• The availability of direct access memory is
country dependent.
only each time.
1
2
Press
or press MENU/OK >
[Phonebook] > [View] > MENU/OK
to access the phonebook list.
Select a contact and view the
available information.
Search a record
You can search the phonebook records
in these ways:
• Scroll the contacts list.
Press
and
to scroll through
the phonebook list.
Press
or press MENU/OK >
[Phonebook] > [View] to access the
phonebook list.
Press the alphanumerical key that
matches the character.
»» The first record that starts with
this character is displayed.
Call from the phonebook
1
Note
•• You can view the phonebook on one handset
Press
or press MENU/OK >
[Phonebook] > [View] to access the
phonebook list.
Enter the first character of a
contact
Note
View the phonebook
Enter the first character of the
contact.
2
3
Press
or press MENU/OK >
[Phonebook] > [View] > MENU/OK
to access the phonebook list.
Select a contact in the phonebook
list.
Press
to make the call.
Access the phonebook
during a call
1
2
Press MENU/OK.
Select the contact, then press
MENU/OK to view the number.
EN
17
Add a record
Note
•• If your phonebook memory is full, a
••
1
2
3
4
notification message is displayed on the
handset. Delete some records to add new
ones.
When you change the number of a record, the
new number will overwrite the old number.
Press MENU/OK.
Select [Phonebook] > [Add new],
then press MENU/OK to confirm.
Enter the name, then press MENU/
OK to confirm.
Enter the number, then press
MENU/OK to confirm.
»» Your new record is saved.
Delete a record
1
2
3
4
••
alphanumeric key to enter the selected
character.
Press REDIAL/C to delete the character. Press
and
to move the cursor left and
right.
Edit a record
1
2
3
4
5
18
Press MENU/OK.
Select [Phonebook] > [Edit], then
press MENU/OK to confirm.
Select a contact, then press MENU/
OK to confirm.
Edit the name, then press MENU/
OK to confirm.
Edit the number, then press MENU/
OK to confirm.
»» The record is saved.
EN
Select [Phonebook] > [Delete], then
press MENU/OK to confirm.
Select a contact, then press MENU/
OK to confirm.
»» A confirmation request is
displayed on the handset.
Press MENU/OK to confirm.
»» The record is deleted.
Delete all records
1
2
Tip
•• Press and hold to insert a pause.
•• Press once or several times on the
Press MENU/OK.
3
Press MENU/OK.
Select [Phonebook] > [Delete all],
press MENU/OK to confirm.
»» A confirmation request is
displayed on the handset.
Press MENU/OK to confirm.
»» All records (except the 2 direct
access memory records) are
deleted.
8 Call log
The call log stores the call history of all
missed or received calls. The incoming
call history includes the name and
number of the caller, call time and date.
This feature is available if you have
registered to the caller ID service with
your service provider.
Your phone can store up to 50 call
records. The call log icon on the
handset flashes to remind you of any
unanswered calls. If the caller allows the
display of his identity, you can view his
name or number. The call records are
displayed in chronological order with
the most recent received call at the top
of the list.
Note
Note
•• This is a country dependent feature.
Select the call list type
1
2
3
1
2
valid before you can call back directly from the
call list.
Icons
Description
It remains steadily on when
browsing incoming calls in the
call log.
It flashes when there is a new
missed call.
It remains steadily on when
browsing the missed calls in call
log.
Select an option, then press MENU/
OK to confirm.
Press
.
»» The incoming call log is
displayed.
Select a record, then press MENU/
OK and select [View] for more
available information.
Save a call record to the
phonebook
1
2
3
4
5
Call list type
Select [Services] > [Call list type],
then press MENU/OK to confirm.
View the call records
•• Make sure that the number in the call list is
The icons shown on the screen tell you
whether they are missed/received calls.
Press MENU/OK.
Press
.
»» The incoming call log is
displayed.
Select a record, then press MENU/
OK to confirm.
Select [Save number], then press
MENU/OK to confirm.
Enter and edit the name, then press
MENU/OK to confirm.
Enter and edit the number, then
press MENU/OK to confirm.
»» The record is saved.
You can set if you can see all incoming
calls or only missed calls from the call
log.
EN
19
Return a call
1
2
3
Press
.
Select a record on the list.
Press
to make the call.
Delete a call record
1
2
3
4
Press
.
»» The incoming call log is
displayed.
Select a record, then press MENU/
OK to confirm.
Select [Delete], then press MENU/
OK to confirm.
»» A confirmation request is
displayed on the handset..
Press MENU/OK to confirm.
»» The record is deleted.
Delete all call records
1
2
3
4
20
Press
.
»» The incoming call log is
displayed.
Press MENU/OK to enter the
options menu.
Select [Delete all], then press
MENU/OK to confirm.
»» A confirmation request is
displayed on the handset..
Press MENU/OK to confirm.
»» All records are deleted.
EN
9 Redial list
The redial list stores the call history of
dialed calls. It includes the names and/
or numbers you have called. This phone
can store up to 20 redial records.
View the redial records
Press REDIAL/C.
2
3
4
Redial a call
2
1
2
3
Select a record, then press .
»» The number is dialed out.
Save a call record to the
phonebook
1
2
3
4
5
Select [Delete], then press MENU/
OK to confirm.
»» A confirmation request is
displayed on the handset..
Press MENU/OK to confirm.
»» The record is deleted.
Delete all redial records
1
Press REDIAL/C.
Select a record, then press MENU/
OK to confirm.
4
Press REDIAL/C to enter the list of
dialed calls.
Press MENU/OK to enter the
options menu.
Select [Delete all], then press
MENU/OK to confirm.
»» A confirmation request is
displayed on the handset..
Press MENU/OK to confirm.
»» All records are deleted.
Press REDIAL/C to enter the list of
dialed calls.
Select a record, then press MENU/
OK to confirm.
Select [Save number], then press
MENU/OK to confirm.
Enter and edit the name, then press
MENU/OK to confirm.
Enter and edit the number, then
press MENU/OK to confirm.
»» The record is saved.
Delete a redial record
1
Press REDIAL/C to enter the list of
dialed calls.
EN
21
10Phone
settings
3
Select [On]/[Off], then press MENU/
OK to confirm.
»» The setting is saved.
Set the docking tone
You can customize the settings to make
it your own phone.
Sound settings
Set the handset's ringtone
volume
Docking tone is the sound made when
you place the handset on the base
station or charger.
1
2
3
You can select among 5 ringtone
volume levels or [Off].
1
2
3
Set the battery tone
Select a volume level, then press
MENU/OK to confirm.
»» The setting is saved.
1
2
Battery tone is the sound made when
the battery is low and needs recharging.
3
Press MENU/OK.
Select [Phone setup] > [Sounds] >
[Ring tones], then press MENU/OK
to confirm.
Select a ringtone, then press
MENU/OK to confirm.
»» The setting is saved.
Set the key tone
Key tone is the sound made when you
press a key on the handset.
1
2
22
Select [On]/[Off], then press MENU/
OK to confirm.
»» The setting is saved.
Select [Phone setup] > [Sounds] >
[Ring volume], then press MENU/
OK to confirm.
You can select from 10 ringtones.
3
Select [Phone setup] > [Sounds] >
[Docking tone], then press MENU/
OK to confirm.
Press MENU/OK.
Set the handset's ringtone
1
2
Press MENU/OK.
Select [Phone setup] > [Sounds] >
[Battery tone], then press MENU/
OK to confirm.
Select [On]/[Off], then press MENU/
OK to confirm.
»» The setting is saved.
Name the handset
The name of the handset can be up
to 12 characters. It is displayed on the
handset screen in standby mode.
1
2
Press MENU/OK.
3
Select [Phone setup] > [Sounds] >
[Key tone], then press MENU/OK to
confirm.
4
EN
Press MENU/OK.
Press MENU/OK.
Select [Phone setup] > [Phone
name], then press MENU/OK to
confirm.
Enter or edit the name. To erase a
character, press REDIAL/C.
Press MENU/OK to confirm.
»» The setting is saved.
Set the date and time
Note
•• Make sure that all the handsets registered to
For information, see 'Set the date and
time' in the 'Get started' section.
Set the display language
Note
•• This feature only applies to models with
multiple-language support.
•• Languages available vary from country to
country.
1
2
3
••
the base station are M560/M565 in order to
have the ECO+ feature functioning properly.
When ECO+ is activated, the standby time is
reduced. This is because in ECO+ mode the
base station is not transmitting any signal in
standby mode; therefore the handset needs
to “listen” more frequently for signals from the
base station to detect incoming calls or other
requests from the base station. The time it
takes for the handset to access features like
call setup, call log, paging, and phonebook
browsing is also delayed. The handset will not
alert you to link loss in case of power loss or
moving out of range.
Press MENU/OK.
Select [Phone setup] > [Language],
then press MENU/OK to confirm.
Select a language, then press
MENU/OK to confirm.
»» The setting is saved.
ECO+ mode
When the ECO+ mode is activated, it
eliminates the radiation of the handset
and base station in standby mode.
1
2
3
Press MENU/OK.
Select [Phone setup] >[ECO+
mode], then press MENU/OK to
confirm.
Select [On]/[Off], and press MENU/
OK to confirm.
»» The setting is saved.
»» ECO+ is displayed in standby
mode after a while.
EN
23
11Telephone
answering
machine
Set the answering
machine language
Note
•• This feature only applies to models with
multiple-language support.
Note
•• Available only for M565.
Your phone includes a telephone
answering machine that records
unanswered calls when it is on. You can
access the answering machine remotely
and change the settings through the
answering machine menu on the
handset.
Turn the answering
machine on or off
1
2
3
Press / or MENU/OK > [Answer
machine].
Select [On/off] > [On]/[Off], then
press MENU/OK to confirm.
Select [Record also]/ [Answer only]
when the answer machine is on,
then press MENU/OK to confirm.
»» The setting is saved.
Note
•• [Record also] means calls are answered and
messages are recorded. [Answer only] means
calls are only answered, messages are not
recorded.
»» The setting is saved.
The answering machine language is the
language for the announcements.
1
2
3
EN
Select [Voice language], then press
MENU/OK to confirm.
Select a language, then press
MENU/OK to confirm.
»» The setting is saved.
Announcements
The announcement is the message
your caller hears when the answering
machine picks up the call. The
answering machine has 2 pre-recorded
announcements: [Record also] and
[Answer only].
Record an announcement
The maximum length of the
announcement you can record
is 3 minutes. The newly recorded
announcement automatically replaces
the old one.
1
2
3
4
24
Press / or MENU/OK > [Answer
machine].
Press / or MENU/OK > [Answer
machine].
Select [Announcement], then press
MENU/OK to confirm.
Select [Answer only] or [Record
also], then press MENU/OK to
confirm.
Select [Record], then press MENU/
OK to confirm.
5
6
Start recording close to the
microphone after the beep.
Press MENU/OK to stop recording
or the recording stops after 3
minutes.
»» You can listen to the newly
recorded announcement on the
handset.
3
4
5
Note
Select [Record also]or [Answer
only], then press MENU/OK to
confirm.
Select [Use default], then press
MENU/OK to confirm.
»» A confirmation request is
displayed on the handset.
Press MENU/OK to confirm.
»» The default announcement is
restored.
•• Make sure that you speak close to
the microphone when you record an
announcement.
Listen to the announcement
1
2
3
4
Press / or MENU/OK > [Answer
machine].
Incoming messages
Each message can be up to 3 minutes
long. When you receive new messages,
the new message indicator flashes
on the answering machine and the
handset.
Select [Announcement], then press
MENU/OK to confirm.
Select [Answer only] or [Record
also], then press MENU/OK to
confirm.
Select [Play], then press MENU/OK
to confirm.
»» You can listen to the current
announcement.
Note
•• If you pick up the phone when the caller
••
leaves a message, the recording stops and you
can talk to the caller directly.
If the memory is full, the answering machine
switches to [Answer only] automatically.
Delete old messages to receive new ones.
Listen to the incoming messages
Note
•• You can no longer listen to the announcement
when you pick up an incoming call.
Restore the default
announcement
1
2
Press / or MENU/OK > [Answer
machine].
Select [Announcement], then press
MENU/OK to confirm.
You can listen to the incoming
messages in the sequence they are
recorded.
• If there are new messages, press
/ to listen. If there is no new
message, press / , then MENU/
OK to listen to old messages.
• Press MENU/OK > [Answer
machine] > [Play], then press
MENU/OK to confirm.
»» New messages start playing. Old
messages start playing if there is
no new message.
•
Press REDIAL/C to stop listening.
EN
25
•
•
Press MENU/OK to enter the
options menu.
Press
/
to increase/
decrease the volume.
Delete an incoming message
1
2
3
Note
•• Make sure that the answering machine
is switched on before this feature can be
applied.
When you listen to the message,
press MENU/OK to enter the
options menu.
Select [Delete], then press MENU/
OK to confirm.
»» The current message is deleted.
Tip
•• When you access the answering machine
remotely, you are recommended to set the
ring delay to [Toll saver] mode. This is a cost
effective way to manage your messages.
When there are new messages, the answering
machine picks up the call after 3 rings; When
there is no messages, it picks up the call after
5 rings.
Delete all old incoming
messages
1
2
3
Press /
machine]
or MENU/OK > [Answer
Select [Delete all], then press
MENU/OK to confirm.
»» A confirmation request is
displayed on the handset.
Press MENU/OK to confirm.
»» All old messages are
permanently deleted.
Remote access
You can operate your answering
machine when you are away from
home. Simply make a call to your phone
with a touch tone phone and enter your
4-digit PIN code.
Note
•• You can only delete the read messages. No
deleted messages can be recovered.
Select a new setting, then press
MENU/OK to confirm.
»» The setting is saved.
Note
•• The remote access PIN code is the same as
your system PIN. The preset PIN is 0000.
Set the ring delay
You can set the number of times the
phone rings before the answering
machine picks up the call.
1
2
26
Press /
machine]
or MENU/OK > [Answer
Select [Ring delay], then press
MENU/OK to confirm.
EN
Activate/deactivate the remote
access
You can allow or block remote access to
the answering machine.
1
2
Press /
machine]
or MENU/OK > [Answer
Select [Remote access], then press
MENU/OK to confirm.
3
Select [Activate]/[Deactivate], then
press MENU/OK to confirm.
»» The setting is saved.
Note
•• When there is no message, the phone hangs
up automatically if no key is pressed for 8
seconds.
Change the PIN code
1
2
3
4
5
Press / or MENU/OK > [Answer
machine].
Select [Remote access] > [Change
PIN], then press MENU/OK to
confirm.
Enter the old PIN, then press
MENU/OK to confirm.
2
3
Key
1
2
3
6
7
Enter the new PIN code, then press
MENU/OK to confirm.
Enter the new PIN code again, then
press MENU/OK to confirm.
»» The setting is saved.
Access the answering machine
remotely
1
Remote access commands
8
9
Function
Listen to the previous message.
Listen to messages.
Skip to the next message.
Delete the current message.
Switch the answering machine
on (not available when you listen
to the messages).
Stop listening to the message.
Switch the answering machine
off.
(not available when you listen to
the messages).
Make a call to your home number
with a touch tone phone.
Enter # when you hear the
announcement.
Enter your PIN code.
»» You now have access to your
answering machine, and you can
now listen to the new messages.
Note
•• You have 2 chances to enter the correct PIN
code before your phone hangs up.
4
Press a key to carry out a function.
See the Remote access commands
table below for a list of available
functions.
EN
27
12 Privacy mode
You can access the privacy mode menu
to block outgoing and incoming calls.
3
Enter the privacy mode PIN/
passcode. The default PIN is 0000.
Then press MENU/OK to confirm.
4
Select [Call barring] > [Barring
number], then press MENU/OK to
confirm.
5
Call barring (block
outgoing calls)
You can block outgoing calls to
numbers, such as overseas calls or
undesirable hotlines by barring calls
that start with certain digits. You can
create 2 sets of numbers with 4 digits
at maximum for each set of numbers.
When you make a call that starts with
one of these 2 sets of numbers, the
outgoing call is then barred.
Activate/deactivate the
outgoing call block mode
1
2
3
4
Press MENU/OK.
Select [Privacy mode], then press
MENU/OK to confirm.
Enter the privacy mode PIN/
passcode. The default PIN/
passcode is 0000. Then press
MENU/OK to confirm.
Select [Call barring] > [Barring
mode] > [On]/[Off], then press
MENU/OK to confirm.
»» The setting is saved.
6
Select a number from the list, then
press MENU/OK to confirm.
Edit the number, then press MENU/
OK to confirm.
»» The setting is saved.
Block incoming calls
You can put numbers into the blacklist
to block incoming calls from certain
undesirable numbers. You can create
4 sets of numbers with 24 digits at
maximum for each set of numbers.
When there is an incoming call with
leading digits that match any one of
these 4 sets of numbers, the ringer will
be muted.
Example:
Block number = 0123
Incoming call number = 0123456789
The call is blocked.
Block number = 23456789
Incoming call number = 03123456789
The call is not blocked.
Note
•• Make sure you have subscribed to the caller ID
service before you use this feature.
Add new numbers to the
outgoing call block list
1
2
28
•• The contact's name in phonebook will not be
displayed if this contact's number matches the
record saved in the blacklist.
Press MENU/OK.
Select [Privacy mode], then press
MENU/OK to confirm.
EN
Activate/deactivate the blacklist
1
Press MENU/OK.
2
3
4
Select [Privacy mode], then press
MENU/OK to confirm.
Enter the privacy mode PIN/
passcode. The default PIN is 0000.
Then press MENU/OK to confirm.
Select [Call block] > [Block mode] >
[On]/[Off], then press MENU/OK to
confirm.
»» The setting is saved.
Add blacklist numbers
1
2
3
4
5
Press MENU/OK.
Select [Privacy mode], then press
MENU/OK to confirm.
Enter the privacy mode PIN/
passcode. The default PIN is 0000.
Then press MENU/OK to confirm.
Select [Call block] > [Block number],
then press MENU/OK to confirm.
Enter the number, then press
MENU/OK to confirm.
»» The setting is saved.
Change the privacy mode
PIN/passcode
1
2
3
4
5
6
Press MENU/OK.
Select [Privacy mode], then press
MENU/OK to confirm.
Enter the old PIN/passcode. The
default PIN is 0000. Then press
MENU/OK to confirm.
Select [Change PIN], then press
MENU/OK to confirm.
Enter the new PIN/passcode, then
press MENU/OK to confirm.
Enter the new PIN/passcode again,
then press MENU/OK to confirm.
»» The setting is saved.
EN
29
13Services
2
3
The phone supports a number of
features that help you handle and
manage the calls.
Call list type
You can set if you can see all incoming
calls or only missed calls from the call
log.
Note
•• This is a country dependent feature.
3
Press MENU/OK.
Select [Services]> [Call list type],
then press MENU/OK to confirm.
Select an option, then press MENU/
OK to confirm.
Auto conference
To join an external call with another
handset, press .
Select [Auto]/[Off], then press
MENU/OK to confirm.
»» The setting is saved.
Network type
Note
•• This is a country dependent feature. It only
applies to models with network type support.
1
2
3
Select the call list type
1
2
Select [Services] > [Conference],
then press MENU/OK to confirm.
Press MENU/OK.
Select [Services] > [Network type],
then press MENU/OK.
Select a network type, then press
MENU/OK.
»» The setting is saved.
Auto prefix
This feature checks and formats your
outgoing call number before it is dialed
out. The prefix number can replace the
detect number you set in the menu.
For example, you set 604 as the detect
number and 1250 as the prefix. When
you have dialed out a number such as
6043338888, your phone changes the
number to 12503338888 when it dials
out.
Note
Note
•• This feature is available only for multi-handset
versions.
Activate/Deactivate auto
conference
1
Press MENU/OK.
30
EN
•• The maximum length of a detect number is 5
••
digits. The maximum length of an auto prefix
number is 10 digits.
This is a country dependent feature.
Set auto prefix
1
2
3
4
Dial mode
Press MENU/OK.
Select [Services] > [Auto prefix],
then press MENU/OK to confirm.
Enter the detect number, then press
MENU/OK to confirm.
Enter the prefix number, then press
MENU/OK to confirm.
»» The setting is saved.
Note
•• This feature only applies to models that
support both tone and pulse dial.
Dial mode is the telephone signal used
in your country. The phone supports
tone (DTMF) and pulse (rotary) dial.
Consult the service provider for detailed
information.
Note
•• To enter a pause, press and hold .
•• If the prefix number is set and the detect
••
number is left empty, the prefix number is
added to all outgoing calls.
The feature is unavailable if the dialed number
starts with * and #.
Set the dial mode
1
2
3
Press MENU/OK.
Select [Services] > [Dial mode], then
press MENU/OK to confirm.
Select a dial mode, then press
MENU/OK to confirm.
»» The setting is saved.
Select the recall duration
Note
Make sure that the recall time is set
correctly before you can answer a
second call. In normal case, the phone
is already preset for the recall duration.
You can select among 3 options: [Short],
[Medium] and [Long]. The number of
available options varies with different
countries. For details, consult your
service provider.
1
2
3
•• If your phone is in pulse dial mode, press
during a call for temporary tone mode. Digits
entered for this call are then sent out as tone
signals.
Auto clock
Press MENU/OK.
Select [Services] > [Recall time],
then press MENU/OK to confirm.
Select an option, then press MENU/
OK to confirm.
»» The setting is saved.
Note
•• This service is network dependent.
•• Make sure you have subscribed to the caller ID
service before you use this feature.
It synchronizes the date and time
on your phone with the public
switched telephone network (PSTN)
automatically. For the date to be
synchronized, make sure the current
year is set.
1
Press MENU/OK.
EN
31
2
3
Select [Services] > [Auto clock], then
press MENU/OK to confirm.
Select [On]/[Off]. Press MENU/OK.
»» The setting is saved.
Register additional
handsets
You can register additional handsets to
the base station. The base station can
register up to 4 handsets.
1
2
3
Unregister the handsets
1
2
3
4
5
32
Enter the system PIN. (The preset
PIN is 0000). Press REDIAL/C to
remove the number.
Select the handset to be
unregistered.
Press MENU/OK to confirm.
»» The handset is unregistered.
•• The handset name is displayed beside the
Press and hold on the base
station for 10 seconds.
•• A handset cannot unregister itself.
Enter the system PIN. Press
REDIAL/C to make corrections.
Then press MENU/OK to confirm
the PIN.
»» Registration is complete in
less than 2 minutes. The base
automatically assigns a handset
number to the handset.
•• If the PIN is incorrect or no base is found
••
Select [Services] > [Unregister], then
press MENU/OK to confirm.
You can register your handset as
follows:
• If the handset is in [Unregistered]
status, press MENU/OK.
• If the handset is in [searching]
and [Unavailable] status,
press MENU/OK > [Services] >
[Register] > MENU/OK.
Tip
handset number in standby mode.
Note
Restore default settings
You can reset your phone settings to the
original factory settings.
1
2
Note
••
Press MENU/OK.
within a certain period, a notification message
will be displayed on your handset.
If registration fails, unplug the power adapter
from the base station and plug it back. Wait for
15 seconds, and then repeat the registration
procedure.
The preset PIN is 0000. No change can be
made on it.
EN
3
Press MENU/OK.
Select [Services] > [Reset], then
press MENU/OK to confirm.
»» A confirmation request is
displayed on the handset.
Press MENU/OK to confirm.
»» All settings (except the
phonebook and direct access
keys information) are reset.
14Technical
data
General specification and features
• Talk time: 16 hours
• Standby time: 250 hours
• Range indoor: 50 meters
• Range outdoor: 300 meters
• Phonebook list with 100 entries
• Redial list with 20 entries
• Call log with 50 entries
• Answering machine with 30 minutes
recording time
• Caller identification standard
support: FSK, DTMF
Battery
• Philips: 2 x AAA Ni-MH 1.2V 500
mAh rechargeable batteries
Power adapter
Base and charger
• Tenpao: S003GB0600050, input:
100-240 V~, 50/60 Hz 150 mA,
output: 6 Vdc 500 mA
RF output power
• < 24 dBm
Frequency Band
• 1880 MHz ~ 1900 MHz
Power consumption
• Power consumption in standby
mode: around 0.7 W (M560), 0.75 W
(M565)
Weight and dimensions
• Handset: 132 grams
213 x 50 x 44 mm (H x W x D)
• Base: 86 grams
215 x 50 x 35 mm (H x W x D)
• Charger: 72 grams
215 x 50 x 35 mm (H x W x D)
EN
33
15Notice
regarding exposure to electromagnetic
fields.
Declaration of conformity
Disposal of your old
product and battery
Hereby, Gibson Innovations declares
that this product is in compliance with
the essential requirements and other
relevant provisions of Directive 2014/53/
EU. You can find the Declaration of
Conformity on www.p4c.philips.com.
Your product is designed and
manufactured with high quality
materials and components, which can
be recycled and reused.
Use GAP standard
compliance
The GAP standard guarantees that
all DECT™ GAP handsets and base
stations comply with a minimum
operating standard irrespective of their
make. The handset and base station
are GAP compliant, which means they
guarantee the minimum functions:
register a handset, take the line, make
a call and receive a call. The advanced
features may not be available if you use
them with other makes. To register and
use this handset with a GAP compliant
base station of different make, first
follow the procedure described in
the manufacturer's instructions, then
follow the procedure described in this
manual for registering a handset. To
register a handset from different make
to the base station, put the base station
in registration mode, then follow the
procedure described in the handset
manufacturer's instructions.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This symbol means that the product
contains batteries covered by European
Directive 2013/56/EU which cannot be
disposed of with normal household
waste.
Inform yourself about the local separate
collection system for electrical and
electronic products and batteries.
Follow local rules and never dispose of
the product and batteries with normal
household waste. Correct disposal
of old products and batteries helps
prevent negative consequences for the
environment and human health.
Removing the disposable batteries
To remove the disposable batteries, see
section ‘Frequently asked questions’.
Compliance with EMF
This product complies with all
applicable standards and regulations
34
EN
When this logo is attached to a product,
it means a financial contribution has
been paid to the associated national
recovery and recycling system.
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buffer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials
which can be recycled and reused
if disassembled by a specialized
company. Please observe the local
regulations regarding the disposal
of packaging materials, exhausted
batteries and old equipment.
EN
35
16Frequently
asked
questions
No signal bar is displayed on the
screen.
•• The handset is out of range. Move it
closer to the base station.
•• If the handset displays
[Unregistered], register your
handset.
Tip
•• For further information, see the chapter
'Services', section 'Register additional
handsets'.
If I fail to pair (register) the additional
handsets to the base station, what do
I do?
Your base memory is full. Unregister the
unused handsets and try again.
Tip
•• For further information, see the chapter
'Services', section 'Unregister the handsets'.
The range is short. How can I improve
it?
The range is subject to environmental
factors, like electrical devices or walls in
between.
•• Move the base station to another
corner/room.
•• Move the base station away from
other electrical appliances nearby
that could interfere with the range
(like routers, TV, radio, etc.).
•• Do not put the base station on a
metallic desk or a metallic table top.
36
EN
My handset is in searching or
unavailable status, what do I do?
• Make sure that the base station has
power supply.
• Move the handset closer to the
base station.
• Register the handset to the base
station.
I have chosen a wrong country in
Welcome screen, what do I do.
Reset your phone settings to the
original factory settings (see 'Restore
default settings' on page 32).
No dialing tone/no free line.
•• Check your phone connections.
•• The handset is out of range. Move it
closer to the base station.
•• The handset is in [searching] or
[Unavailable] status. Register the
handset to the base station.
No docking tone.
•• The handset is not placed properly
on the base station/charger.
•• The charging contacts are dirty.
Disconnect the power supply first
and clean the contacts with a damp
cloth.
I cannot change the settings of my
voice mail, what do I do?
The voice mail service is managed by
your service provider but not the phone
itself. Contact your service provider to
change the settings.
The handset on the charger does not
charge or the battery discharges too
fast.
•• Make sure the batteries are inserted
correctly.
•• Make sure the handset is placed
properly on the charger. If the
docking tone is turned on, you can
hear the docking tone when you
place the handset on the charging
cradle.
••
••
••
The charging contacts are dirty.
Disconnect the power supply first
and clean the contacts with a damp
cloth.
The battery is not fully recharged.
Leave the handset on the charging
cradle for at least 8 hours or until
the battery icon on the handset
stops scrolling and indicates full bar.
The batteries are old or defective.
Purchase and replace with new
rechargeable batteries with the
same specifications. To remove the
battery door, refer to the instruction
in the following picture.
No display.
•• Make sure the batteries are
charged.
•• Make sure there is power and the
phone is connected.
The handset does not ring.
•• Make sure the handset ringtone is
turned on.
•• Make sure the handset is registered
to the base station.
The caller ID does not display.
•• The service is not activated. Check
with your service provider.
•• The caller's information is withheld
or unavailable.
The handset cannot display characters
* and #.
Characters * and # respectively appear
as small ‘n’ and small ‘o’ in the LCD
display. This is normal behavior because
of the 7-segment in the 2nd row of the
display (you can find the characters on
these 4 buttons:
and
).
Note
•• If the above solutions do not help, disconnect
the power supply from both the handset and
base station. Try again after 1 minute.
Bad audio (crackles, echo, etc.).
•• The handset is nearly out of range.
Move it closer to the base station.
•• The phone receives interference
from the nearby electrical
appliances. Move the base station
away from them.
•• The phone is at a location with thick
walls. Move the base away from
them.
•• The phone receives interference
from the DSL (digital subscriber
line) connection. Install a DSL filter
to prevent the noise. Contact your
service provider for the DSL filter.
EN
37
17Appendix
8
9
tuv8ùúüūųμ
wxyz9øΩΞΨž
Text and number input
tables
Key
0
1
Key
2
3
4
5
6
7
8
9
Upper case characters (for Greek)
Space . 0 , / : ; " ' ! ¡ ? ¿ * + - % \^ ~|
1@_#=<>()&€£$¥[]{}¤
§ ...
ABГ2ABCÆÄÅÇ
ΔΕΖ3DEFÉ
ΗΘΙ4GHI
ΚΛΜ5JKL
ΝΞΟ6MNOÑÖ
ΠΡΣ7PQRS
Τ Υ Φ 8T UV Ü
Χ Ψ Ω 9 W XY Z Ø
0
1
2
3
4
5
6
7
8
9
Key
0
1
2
3
4
5
6
7
38
Upper case characters (for
English/French/ German/
Italian/Turkish/Portuguese/
Spanish/Dutch/Danish/Finnish/
Norwegian/ Swedish/Romanian/
Polish/Czech/Hungarian/
Slovakian/Slovenian/Croatian/
Lithuanian/Estonian/Latvian/
Bulgarian)
Space . 0 , / : ; " ' ! ¡ ? ¿ * + - % \^ ~|
1@_#=<>()&€£$¥[]{}¤
§ ...
ABC2ÀÂÆÁÃÄÅĄĀÇČ
DEF3ÈÉÊËĖĘĒΔΦ
GHI4ĞÍÏĮĪİΓ
JKL5Λ
MNO6ÑÓÔÕÖ
PQRS7ŞŠΠΘΣ
T UV 8 Ù Ú Ü Ū Ų
W XY Z 9 Ø Ω Ξ Ψ Ž
Lower case characters (for
English/French/ German/
Italian/Turkish/Portuguese/
Spanish/Dutch/Danish/Finnish/
Norwegian/Swedish)
Space . 0 , / : ; " ' ! ¡ ? ¿ * + - % \ ^ ~ |
1@_#=<>()&€£$¥[]{}¤
§…
abc2àâæáãäåąāçč
def3èéêëėęēΔΦ
ghi4ğíìïįīıΓ
jkl5Λ
mno6ñóôõöò
pqrs7βşšΠΘΣ
EN
Key
0
1
2
3
4
5
6
7
8
9
Lower case characters (for Greek)
Space . 0 , / : ; " ' ! ¡ ? ¿ * + - % \ ^ ~ |
1@_#=<>()&€£$¥[]{}¤§
…
αβγ2abcàæäå
δεζ3defèé
ηθι4ghiì
κλμ5jklΛ
νξο6mnoñöò
πρσς7pqrsß
τυφ8tuvùü
χψω9wxyzø
Key
0
1
2
3
4
5
6
7
8
9
Key
0
1
2
3
4
5
6
7
8
9
Upper case characters (for
Serbian)
Space . 0 , / : ; " ' ! ¡ ? ¿ * + - % \^ ~|
1@_#=<>()&€£$¥[]{}¤
§ ...
ABCЂĆČ2АБВГ
DEFЈĐ3ДЕЖЗΔΦ
GHIЉ4ИЙКЛΓ
JKLЊ5МНОПΛ
MNOЋ6РСТУ
PQRSҖŠ7ФХЦЧΠΘΣß
T UV 8 Ш Щ Ъ Ы
W XY Z Ž 9 Ь Э Ю Я Ω Ξ Ψ
Lower case characters (for
Serbian)
Space . 0 , / : ; " ' ! ¡ ? ¿ * + - % \ ^ ~ |
1@_#=<>()&€£$¥[]{}¤
§…
abcЂĆČ2АБВГ
defЈĐ3ДЕЖЗ
ghiЉ4ИЙКЛ
jklЊ5МНОП
mnoЋ6РСТУ
pqrsҖŠ7ФХЦЧΠΘΣß
t u v Lj 8 Ш Щ Ъ Ы
wxyzŽ9ЬЭЮЯΩΞΨ
2016 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold
under the responsibility of Gibson Innovations Ltd., and
Gibson Innovations Ltd. is the warrantor in relation to
this product.
Philips and the Philips’ Shield Emblem are registered
trademarks of Koninklijke Philips N.V.
UM_M560-M565_90_EN_V1.0
WK1618
Download PDF
Similar pages