BESPARA
AU
ENGLISH
4
ENGLISH
Table of contents
Safety information Product description Control panel
Washing programmes
Daily check
Daily use
4
4
6
7
8
9
10
Safety Information
Before using the appliance for the first time
carefully read this quick reference guide and
the assembly instruction!
The control panel of this dishwasher
activates pushing any button except cancel/
off button.
For energy saving the control panel
deactivates automatically after 30 seconds
if no cycle has started.
Removing the packaging and inspecting
the contents
After unpacking, make sure that the
dishwasher is undamaged and that the
door closes correctly. If in doubt, contact a
qualified technician or your local retailer.
Before using the dishwasher for the first
time
• The appliance is designed to operate
with a minimum ambient temperature
of 5°C.
• This dishwasher has been tested by
the manufacturer to ensure it functions
correctly. Such testing may leave slight
drips/ water marks which will disappear
with the first wash.
Energy and water savings
• Do not rinse crockery under running
water.
• Always fully load the dishwasher before
running it or select the “Half load/
Multizone” option (if available).
• If ecological energy sources are
available such as solar panel heating,
heat pumps or centralised heating
How to load the racks
Cleaning and maintenance
What to do if ... Environmental concerns
IKEA warranty
10
13
14
18
19
systems, the appliance may be
connected to the hot water mains up to
a maximum temperature of 60°C.
Make sure the water inlet hose is of
the correct type (“70°C Max” or “90°C
Max”).
Child safety
• Keep the packaging materials out of the
reach of children.
• Children must not be allowed to play
with the dishwasher.
• Store the detergent, rinse aid and salt
out of the reach of children
Safety warnings
• This appliance is not intended for use by
persons (including) children with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
• Children should be supervised to ensure
they do not play with the appliance.
• Do not operate the appliance in the
open air.
• Do not store flammable materials in
close proximity to the dishwasher.
• The water in the dishwasher is not
potable.
• Do not use solvents inside the
dishwasher: risk of explosion!
• The door should not be left in the open
position since this could present a
tripping hazard.
ENGLISH
• The open dishwasher door can only
support the weight of the loaded rack
when pulled out. Do not rest objects on
the open door or sit or stand on it.
• Sharp items that might cause injury
(e.g. knives), must be placed in the
cutlery basket with the sharp end facing
downwards. Long-handled utensils must
be arranged horizontally in the upper
rack, with the sharp end facing away
from the front of the appliance.
• Before cleaning or carrying out
maintenance, disconnect the mains plug
and turn off the water tap; also in the
event of any malfunction.
• Repairs and technical modifications must
be carried out exclusively by a qualified
technician.
WARNING: Some Dishwasher detergents
are strongly alkaline. They can be extremely
dangerous if swallowed. Avoid contact with
the skin and eyes and keep children away
from the dishwasher when the door is open.
Check the detergent receptacle is empty
after completion of the wash cycle.
Water connection
• Connection to the mains water supply
must be carried out by a qualified
technician in compliance with the
manufacturer’s instructions and
applicable local safety regulations.
• All local water board regulations
must be complied with. Water supply
pressure: 0.03 - 1.0 MPa.
• The inlet hose must be securely clamped
to the water tap to prevent leaks.
• The inlet water temperature varies
according to the model installed. Inlet
hose marked: “25°C Max”: up to a
maximum of 25°C. Other models: up to
a maximum of 60°C.
• Depending on the appliance model, the
solenoid valve of the inlet hose will be
activated by the mains voltage.
• Make sure the inlet and drain hoses are
5
kink-free and are not crushed.
• Fix the drain hose to the siphon with
a clamp to prevent it from coming off
during operation.
• When installing the appliance, make
sure water can drain freely (remove the
siphon plug if necessary).
• Do not use old or damaged hoses. Use
only the hoses provided or new ones,
which can be requested from the AfterSales Service.
• If hoses are not long enough, contact
your local dealer.
• Do not cut hoses and, in the case of
appliances fitted with a waterstop
system, do not immerse the plastic
casing containing the inlet hose in water.
• Before using the appliance for the first
time, check the water inlet and drain
hose for leaks.
Electrical Connection
• All local electricity board regulations
must be complied with.
• Voltage information is shown on the
rating plate mounted inside the door on
the right hand side.
• The appliance must be earthed as
prescribed by law.
• Do not use extension leads or multiple
adapters.
• If the power cable is damaged, replace
it with an identical one. The power cable
must only be replaced by a qualified
technician.
• After appliance installation, the mains
plug must be easily accessible so that
the appliance can be unplugged if
necessary at any time.
General indications
• The appliance must only be used in the
household and according its purpose.
• Do not use the dishwasher until it has
been fully assembled.
• Do not use the dishwasher if it has been
damaged in transit. Contact After-Sales
ENGLISH
6
Service or your local dealer.
• Before carrying out any cleaning or
maintenance operations, unplug the
appliance and turn off the water tap.
The same applies in the event of a
malfunction.
• Do not use abrasive products or alcohol
on the control panels.
the water drain away. Make sure there is at
least 1 kg of dissolved regeneration salt in
the salt reservoir, to protect the appliance
from temperatures of up to -20°C. When the
program resumes, an error message may be
indicated (see page 14).
CANCEL/Off indicator blinks 6 times - the
appliance must remain at an ambient
temperature of min. 5°C for at least 24
hours.
After eliminating these faults, RESET the
appliance (see chapter “What to do if...”).
Resistance to frost
If the appliance is placed in surroundings
exposed to the risk of frost, it must be
drained completely. Turn off the water tap,
remove the inlet and outlet hoses, and let all
Product description
2
5
6
7
1
4
3
1 Control panel
2 Upper basket
3 Rinse aid dispenser
4 Detergent dispenser
5 Upper spray arm
6 Lower rack
7 Lower spray arm
ENGLISH
7
Control panel
A
A PROGRAM SELECTION BUTTON
Push “Programs“ button (repeatedly)
until the indicator of the required
program lights up (see “washing
programmes”).
B ANTIBACTERIAL RINSE
This function activates an antibacterial
rinse at the end of the wash cycle,
guaranteeing a further reduction of
bacteria.
Press the button to activate or
deactivate the function.
This function can be used with the
programs indicated in the table of
programs.
The dishwasher door must be kept shut
for the entire duration of the program
in order to guarantee reduction of
bacteria. If the door is opened the
indicator lamp starts flashing.
C DELAYED START BUTTON
The wash cycle can be programmed to
start after 2, 4 or 8 hours.
Then press the Start button.
The wash program will start after the set
time.
B
C
D
E F
D START/RESUME BUTTON
Push this button to start the selected
program: the indicator lights up and
goes off at the end of the program.
When the door is opened during a
washing cycle, the cycle is temporarily
paused: the Start indicator blinks. To
resume the cycle push the Start button
and close the door within 3 seconds.
E CANCEL/OFF BUTTON
Push this button to switch off the control
panel.
If pressed when a program is running
it cancels the program ongoing
draining water for 1 minute.
If pressed when the dishwasher is
switched off it drains any possible
liquids from dishwasher (1 minute
process).
If the indicator flashes repeatedly, see
chapter ”What to do if ...”.
F RINSE AID INDICATOR
When lit (at the end of the cycle), the
rinse aid dispenser needs to be refilled.
ENGLISH
8
Washing programmes
Table of programs
P
Programs
Available
options
Loading instructions
Detergent
Drying
phase
1
Pre-Wash cold
Delay
Crockery to be washed later.
–
No
2
Quickwash 40°C
Delay
Lightly soiled crockery, with no
dried-on food.
X
No
3
Eco 40°C
Delay
Antibacterial
rinse
Normally soiled crockery.
Energy-saving program.
X
Full
4
Intensive 70°C
Delay
Antibacterial
rinse
Recommended program
for heavily soiled crockery,
especially suitable for pans and
saucepans.
X
Full
5
Half Load 50°C
Delay
Ideal for washing a half load
of lightly or normally soiled
crockery
X
Full
Load capacity
12 place settings.
ENGLISH
9
Daily check
Adding rinse aid (not necessary when you
use tablets).
How to adjust the rinse aid dosage
regulator
Check the rinse aid indicator to check
the level into the dispenser
Using a coin or similar object, turn the arrow
to the desired setting.
After adjusting the rinse aid setting, shut the
cover again.
Rinse aid indicator on the control panel
The indicator lamp lights up when RINSE
AID NEEDS TO BE ADDED.
Visual indicator
A
If required, open the cover A (press the
dedicated button).
Add rinse aid to the max. line ~150 ml
The rinse aid dosage can be adjusted to the
detergent used. The lower the setting, the
less rinse aid is dispensed (factory setting:
position 4).
Press the button to open the cover A.
Only use rinse aids recommended for
use in domestic dishwashers.
Immediately wipe away any rinse aid
spilt accidentally. This prevents the
formation of excess suds which can
cause a fault function of the appliance.
If there are streaks: reduce the dosage
by turning the dial to a lower setting
(1-3). If crockery is not perfectly dry:
increase the dosage by turning the dial
to a higher setting (5-6). Plastic dishes
have more difficulty drying and a
higher rinse aid setting will not improve
the situation.
Detergents with rinse aid incorporated
may be effective only with longer
programs. In the case of shorter
programs, detergent residue may be
a problem (if necessary, use powder
detergent). Detergents with rinse aid
incorporated tend to form excess suds.
ENGLISH
10
Daily use
Adding detergent - Use only detergent
specifically for dishwashers in accordance
with the supplier’s recommendations.
Open the cover B (press the dedicated
button).
Insert detergent: Tablet / powder / liquid
into the big chamber.
Only fill the detergent dispenser prior to
starting a wash programme.
Use only one tablet per one cycle, only
placed in detergent dispenser.
Shut the cover by pressing dedicated ribs.
B
How to load the racks
Upper rack
Adjustable flaps (A): In horizontal position
for cups/long utensils/stemmed glasses.
A
A
ENGLISH
11
How to adjust upper rack height
It could be useful to lift up the upper rack to
have more space in lower rack or bring it
down to load long stem glasses.
- Grasp and take out the two lateral handles
(B) - (they must be on the same level) and
lift up or take down the upper rack.
B
How to remove the upper rack
It could be useful to remove the upper rack
to load bulky items in the lower rack.
- Open the two retainers (C) to take off the
upper rack (when the upper rack is in place
the retainers must always be closed).
C
Lower rack
Foldable plate holders (D): they can be
folded down to load pots.
Cutlery baskets (E)
Grid (F): helps to keep the cutlery separate
for better washing results.
Items must be placed in the cutlery
basket with the sharp end facing
downwards.
D
F
E
Arrange crockery so that water does
not collect in cavities, ensuring that the
spray arms turn freely. Only use
dishwasher-proof crockery and dishes.
Do not use the dishwasher for washing
wooden items, aluminium, tin, silver
cutlery or decorated crockery
(unglazed). In the baskets, dishes (e.g.
plates, bowls, pots) must be placed in
a correct way to let water flow down!
Switching on the appliance. Press any
button (except CANCEL/Off button) to
switch on the control panel and start
programming.
Select programme
Overview of programs.
ENGLISH
The corresponding programs for your
appliance can be found on the panel.
Choose program according to washing
programmes.
Duration of the program depends
on the external conditions in the
apartment, temperature and pressure
etc.
Wash cycle
The dishwasher door must be closed and
the water tap open.
To pause the program (e.g. if you want to
insert an item):
-- Open the door with caution (the
program pauses) and insert the item/s,
(beware of HOT steam!).
-- Press the START button and close the
door within 3 seconds (the program
resumes the cycle from where it was
interrupted).
To Cancel the program on running:
-- Open the door, press the CANCEL/Off
button and close the door.
-- (Water drains for up to 1 minute then the
appliance switches off).
To change the program in progress:
-- Open the door, press the CANCEL/Off
button to cancel the running program
and close the door.
-- (Water drains for up to 1 minute then the
appliance switches off).
-- Open the door and press any button
except CANCEL/Off button to switch on
the appliance.
-- Select a new program.
-- Press the START button and close the
door within 3 seconds.
12
Switch off the appliance Everything o.k ...
After the program is completed appliance
turns into Standby mode automatically.
All indicator lamps switch off.
Exercise caution when opening the door:
beware of hot steam.
Unload the appliance starting from the
lower rack in order to avoid any residual
drips of water falling onto crockery below.
For even better drying results, leave
the dishwasher door open a little
before unloading in order to allow
the steam to dissipate, helping the
dishes to dry. The underside of the
kitchen worktop must be protected (see
instructions in ‘Assembly instructions’).
ENGLISH
13
Cleaning and maintenance
Spray arms
Remove blockages/deposits.
Unscrew and remove upper arm (A-B).
Filters
Check and clean if necessary.
Unscrew microfilter, remove it (E) and
remove fine sieve (F).
E
B
A
Unscrew and remove lower arm (C-D).
F
D
C
Clean spray nozzles under running water
(use toothpicks if necessary).
Insert and screw on upper and lower arms
tightly.
Rinse under running water and insert again.
ENGLISH
14
What to do if ...
If a fault occurs, before contacting the After-sales Service, make the following
checks to try and remedy the problem.
Most faults can be remedied by taking the following courses of action, quickly
restoring normal appliance operation.
The appliance...
...is not working/will not start
...the CANCEL/Off indicator
lamp blinks 6 times
...the CANCEL/Off indicator
lamp blinks 6 times/wash
program ended too early
(dishes are dirty and wet)
...the CANCEL/Off indicator
lamp blinks 8 times
Possible causes...
Solutions...
- The appliance must be
switched on.
- Check the household circuit fuse
if there is no power supply.
- The dishwasher door
doesn’t close
- Check if the dishwasher’s door
is closed.
- Delayed start option is
ON.
- Check whether the “Delayed
Start” option (if available) has
been selected. If it has, the
appliance will only start once
the set time has elapsed. If
necessary, set the delayed start
to “0” (RESET the appliance).
- Water tap closed.
- The water tap must be open.
- Kinked water inlet hose or
clogged inlet filters.
- The water inlet hose must not
be kinked and the relative inlet
filter in the water tap connector
must not be dirty or clogged.
- Water pressure too low.
- The water tap must be fully
open during water inlet
(minimum capacity: 0,5 liters per
minute).
- Dirty or clogged filters.
- The filters must not be dirty or
clogged.
- Too little water in the
dishwasher’s water
system.
- Concave items (e.g. Bowls,
cups) must be arranged facing
downwards in the rack.
- Drain hose incorrectly
fitted.
- The drain hose must be fitted
correctly (for high mounted
appliances, leave min. 200-400
mm from the lower edge of
the appliance) - see Assembly
Instruction.
- High level of foam inside.
- Repeat without detergent or
wait until foam disappears.
- Dirty filters.
- Clean the filters.
- Kinked drain hose
- The drain hose must not be
kinked.
- Syphon hose connection
closed.
- The closure disk of the syphon
hose connection must be
removed.
ENGLISH
15
After taking the above course of action, the fault message must be reset. In the majority of cases
the fault is thus eliminated.
RESET: ª Press the CANCEL/Off button.
ª Close the door.
ª Water drains automatically for up to 1 minute.
ª The appliance is now ready to be restarted.
Crockery and cutlery...
...are not perfectly clean/
have food residues
Possible causes...
Solutions...
- Too little space between
dishes ( Incorrect
arrangement of the
concave items in the rack).
- Arrange crockery so that
items do not touch each other.
Concave items (e.g. bowls,
cups) must be arranged facing
downwards in the rack.
- Too little detergent;
detergent too old or
incorrectly stored.
- If necessary, use more detergent,
observing the manufacturer’s
indications as regards dosage.
Always store detergent in a dry
place and do not store it for
excessively long periods of time.
- Temperature not high
enough for heavily soiled
crockery.
- For heavily soiled crockery,
select a wash program with
a higher temperature (see
“washing programmes”) .
- Loading of the
dishwasher using lower
and upper rack in the
same time with “Half load
/ Multizone” option
- If you select the “Half load /
Multizone” option (if available),
remember to load only the
upper rack or only the lower
rack to increase washing power
and thus obtain optimum wash
results.
- Frequent use of Eco 40°C.
- In the event of frequent use
of the Eco programe 40°C (if
available), from time to time
select the intensive o 70°C
program (if available).
- Clogged spray arms,
dirty filters or not fitted
correctly.
- The spray arms must not be
clogged, the filters must not
be dirty and must be fitted
correctly (see “Cleaning and
Maintenance”).
- Spray arms stuck
impeded by crockery or
cutlery.
- The spray arms must be able
to turn freely and must not be
impeded by crockery or cutlery.
ENGLISH
Crockery and cutlery...
...are not dry
16
Possible causes...
- Plastic containers dry
badly.
- Synthetic materials do not dry
well; if wet at end of cycle, wipe
dry.
- Clean dishes left in
dishwasher for a
long time after end of
cycle (e.g. when using
“Delayed start” option).
- In this situation, the presence of
drops of water on dishes and
on the sides of the dishwasher
is normal.
Try releasing the door 5 minutes
before removing the dishes.
- Incorrect arrangement of
the concave items in the
rack.
- Arrange crockery so that water
does not collect in cavities.
- Incorrect dosage the rinse
aid.
- Increase the dosage of rinse aid
(see “Adding rinse aid”).
- Rapid program selected.
- The rapid program 40°C / 45°C
is intended for quickly washing
lightly soiled dishes. If used for
a full load of medium/heavy
soiled dishes, the dishes may
not dry completely. If so, select
a standard-length programme.
For best results, open the door
after the end of the program
and wait 15 minutes before
unloading the dishwasher.
- Tomato/Carrot juice.
- Tomato sauce, for example,
can lead to discolouring of
plastic parts. Powder detergent
is recommended as it allows
slightly higher doses to be
used for improved whitening.
Programs with higher wash
temperatures should be used.
- Dishes unsuitable for
washing in dishwashers
(porcelain).
- Only use dishwasher-proof
crockery and dishes.
- Usage of incorrect
programmes for glasses.
- Dishes should be put together,
to avoid touching each other.
Do not put glassware together
in baskets.
Use suitable programme for
glass.
- Not conform of glasses to
washing in dishwashers
(porcelain).
- Some kinds of glass cannot be
washed in the dishwasher.
...have discoloured plastic
parts
...opaque glasses, etc.
...removable deposits on
glasses
...glasses not sparkling
Solutions...
ENGLISH
Crockery and cutlery...
17
Possible causes...
- Rainbow effect.
- This phenomenon is irreversible.
We recommend in future:
• Be careful – follow
recommended detergent
dosage,
• For combined action tablets
see detergent producer’s
recommendations.
- Not known.
- This phenomenon is inevitable.
Theine alters colours
permanently.
- Pre-wash programme not
used.
- Salty or acidic food residues
can cause rust marks even on
stainless steel cutlery. To avoid
this, always use the pre-wash
programme if the dishes are to
be washed later.
- Rinse aid dosage too low.
- In the presence of marks,
increase the rinse aid dosage
(see “Adding rinse aid”).
- If you use a combined action
detergent, possibly add more
rinse aid.
- Rinse aid dosage too
high.
- In the presence of streaks,
reduce the rinse aid dosage
(see “Adding rinse aid”).
- If you use a combined action
detergent try adding morel
rinse aid.
- Unsuitable dosage of
detergent/rinse aid.
- Only use the amount of
detergent / rinse aid required,
since excessive amounts can
lead to excess suds.
...permanent deposits on
glasses
...tea cups darken and dirt
does not disappear after
washing in dishwasher
...rust marks
...other marks
...streaks
...suds
Solutions...
If, after carrying out the above checks, the
fault persists, disconnect the mains plug and
turn off the water tap. Contact the Aftersales Service (see warranty).
Before contacting our After-Sales Service,
take note of the following:
-- the description of the fault,
-- the appliance type and model,
-- the service code (the number indicated
on the adhesive rating plate) inside the
door on the right-hand side:
ENGLISH
Environmental concerns
1. Packing
The packaging materials are 100%
recyclable and marked with the recycling
symbol.
2. Disposal
The appliance is manufactured using
recyclable materials. If you decide to scrap
the dishwasher, it must be disposed of
in compliance with local waste disposal
regulations. Make it unusable by cutting
off the power cord. To prevent situations of
potential danger to children (e.g. danger of
suffocation), break the lock of the door so
that it can no longer be closed.
This appliance is marked according to
the European directive 2002/96/CE on
Waste Electrical and Electronic Equipment
(WEEE). By ensuring that this appliance is
scrapped suitably, you can help prevent
potentially damaging consequences for the
environment and health. Unsuitable disposal
of an appliance of this type as household
waste could have detrimental effects on
the environment. The symbol
on the
appliance, or on documentation enclosed with
the appliance, indicates that this product must
not be treated as household waste, but must
be delivered to the nearest collection centre
for the recycling of electrical and electronic
appliances. Disposal must be carried out
in accordance with local environmental
regulations for waste disposal. For further
information on the treatment, recovery and
recycling of this appliance, contact your
competent local authority, the collection
service for household waste or the shop where
you purchased the appliance.
18
EC Declaration of conformity
• This appliance has been designed,
constructed and distributed in compliance
with the safety requirements of EC
Directives:
n
2006/95/CE, 89/336/CE, 93/68/CE and
2002/95/CE (RoHS Directive).
We reserve the right to make technical
modifications.
The guarantee is not applicable if fauts are
caused by incorrect use of the appliance.
ENGLISH
19
IKEA GUARANTEE
How long is the IKEA guarantee valid?
This guarantee is valid for five (5) years
from the original date of purchase of your
appliance at IKEA, unless the appliance is
named LAGAN in which case two (2) years
of guarantee apply. The original sales
receipt, is required as proof of purchase. If
service work is carried out under guarantee,
this will not extend the guarantee period for
the appliance.
Which appliances are not covered by the
IKEA five (5) years guarantee?
The range of appliances named LAGAN .
Who will execute the service?
IKEA has appointed Whirlpool (Australia)
Pty Ltd as the authorised service network
partner.
• If you encounter any trouble with the
appliance and wish to register a call
with Whirlpool, please call:
Australia contact centre:
1300 363 344.
What does this guarantee cover?
The guarantee covers applicable faults
of the appliance, as per the terms and
conditions, from the date of purchase from
IKEA. This guarantee applies to domestic
use only. The exceptions are specified under
the headline “What is not covered under this
guarantee?” Within the guarantee period,
the costs to remedy the fault e.g. repairs,
parts, labour and travel will be covered,
provided that the appliance is accessible
for repair without special expenditure.
Replaced parts become the property of
IKEA.
The services will be in-home service for
domestic appliances, and must to be done
by official Whirlpool service network.
Goods presented for repair may be
replaced by refurbished goods of the same
type rather than being repaired.
Refurbished parts may be used to repair the
goods.
If the authorized service agent requests
you to deliver the product directly to them,
please ensure that the appliance is suitably
packaged to prevent any damage during
transportation.
What will IKEA do to correct the problem?
IKEA appointed service provider will
examine the product and decide, at its
sole discretion, if it is covered under this
guarantee. If considered covered, IKEA
service provider or its authorized service
partner through its own service operations,
will then, at its sole discretion, either repair
the defective product or replace it with the
same or a comparable product.
What is not covered under this guarantee?
• Normal wear and tear.
• Deliberate or negligent damage,
damage caused by failure to observe
operating and maintenance instructions,
incorrect installation or by connection
to the wrong voltage, damage caused
by chemical or electrochemical reaction,
rust, abrasion or scratching, corrosion or
water damage including but not limited
to damage caused by excessive lime in
the water supply, damage caused by
abnormal environmental conditions.
• Damage caused from the use of the
appliance in a manner other than
the use for which it was specifically
designed.
• Damage caused by power outages,
electrical power surge or improper
supply voltage via connection to Supply
Authority mains or alternative supply
systems.
• Consumable parts including batteries
and lamps, removable wire, glass and
plastic trays and other accessories.
ENGLISH
• Internal or external damage as a result
of excessive use of cleaning products or
cleaning agents.
• Non-functional and decorative parts
which do not affect normal use of the
appliance, including any scratches and
possible color differences.
• Accidental damage or blockages caused
by foreign objects, eg. coins, underwires,
nails, buttons or jewellery, or substances
and cleaning or unblocking of filters,
drainage systems or soap drawers
• Damage caused by vermin, insects or
pets.
• Note – internal or external cabinet
transport damage must be reported
within 7 days of purchase date.
• Damage to the following parts: ceramic
glass, accessories, crockery and cutlery
baskets, feed and drainage pipes, seals,
lamps and lamp covers, screens, knobs,
casings and parts of casings. Unless such
damages can be proved to have been
caused by production faults.
• Cases where no fault could be found
during a technician’s visit.
• Any consequential loss due to appliance
failure.
• Repairs not carried out by our
appointed service providers and/or an
authorized service contractual partner
or where non original parts have been
used.
• Repairs to parts or systems caused by
unauthorized modifications made to
appliance.
• Repairs caused by installation which is
faulty or not according to specification.
• Problems caused by incorrect or
inadequate venting of the appliance.
• The use of the appliance in a non
domestic environment i.e. professional
use.
• Transportation damages. If a customer
transports the product to his home or
another address, IKEA is not liable for
20
any damage that may occur during
transport.
However, if IKEA delivers the product
to the customer’s delivery address, then
damage to the product that occurs
during this delivery will be covered by
IKEA.
• Cost for carrying out the initial
installation of the IKEA appliance.
However, if an IKEA appointed
service provider or its authorized
service partner repairs or replaces
the appliance under the terms of this
guarantee, the appointed service
provider or its authorized service
partner will reinstall the repaired
appliance or install the replacement, if
necessary.
• The benefits conferred by this express
warranty are in addition to all other
conditions, warranties, guarantees,
rights and remedies expressed or
implied by the Trade Practices Act and
similar State and Territory laws and all
other obligations and liabilities on the
part of the manufacturer or supplier and
nothing contained herein shall restrict or
modify such rights, remedies, obligations
or liabilities.
How country law applies?
Our goods come with guarantees that
cannot be excluded under the Australian
Consumer Law.
You are entitled to a replacement or refund
for a major failure and for compensation for
any other reasonably foreseeable loss or
damage.
You are also entitled to have the goods
repaired or replaced if the goods fail to be
of acceptable quality and the failure does
not amount to a major failure.
Area of validity
The IKEA guarantee applies only to
products purchased and installed in
AUSTRALIA .
ENGLISH
21
The dedicated AFTER SALES for IKEA
appliances
Please don’t hesitate to contact IKEA
appointed After Sales Service Provider to:
• make a service request under this
guarantee;
• ask for clarifications on installation of the
IKEA appliance in the dedicated IKEA
kitchen furniture;
• ask for clarification on functions of IKEA
appliances.
• Call our authorized service network
partner Whirlpool on 1300 363 344
(Australia).
WARRANTY PROCEDURE
Please ensure that installation procedure
entailed in the user manual has been
adhered to and in case of any doubts
please refer to the trouble shooting guide
that has been supplied with the appliance.
• Please read the user guide to ensure
that you are aware of all the features &
benefits of the appliance.
How to reach if you need our service
The Whirlpool call centre team will assist
you on the phone with basic trouble
shooting for your appliance at the time of
warranty call registration.
1300 363 344
Please describe the problem that you are
facing with the appliance in detail along
with your product model number, serial
number, date of purchase at the time of
call registration.
Please also always refer to the IKEA
article number (8 digit code) and 12 digit
service number placed on the rating plate
of your appliance.
SAVE THE SALES RECEIPT!
Kindly keep all these details and
original invoice of purchase handy
during the service technician’s visit to
enable him to carry out the job.
Whirlpool reserves the right not to
register the call under warranty if
you fail to provide these details at
the time of call registration.
Do you need extra help?
For any additional questions not related
to After Sales of your appliances please
contact your nearest IKEA store call centre.
We recommend you read the appliance
documentation carefully before contacting
us.
For details on service agents locations, please
visit – www.whirlpool.com.au/services.
5019 600 00428
© Inter IKEA Systems B.V. 2013
19069
AA-908215-1
Download PDF
Similar pages