Operating Instructions
Basic Guide
Touch screen LCD display
English
Model No.
For business use
TH-75BQE1W
75-inch model
Contents
For more detailed instructions, refer to the
Operating Instructions on the CD-ROM.
Important Safety Instructions······················ 2
FCC STATEMENT··································· 3
Important Safety Notice····························· 4
Safety Precautions··································· 5
Precautions for use·································· 9
Introduction···········································11
Installation············································ 17
Operation············································· 21
Specifications······································· 23
Panasonic Professional Flat Panel Display
Limited Warranty··································· 25
LIMITED WARRANTY STATEMENT·········· 26
Customer Service·································· 27
•• Please read these instructions before operating your set and retain
them for future reference.
•• Illustrations and screens in this Operating Instructions are images for
illustration purposes, and may be different from the actual ones.
*Actual resolution: 3840 × 2160p
EU
DPQX1221ZA
WARNING
Important Safety
Instructions
WARNING: To reduce the risk of electric shock,
do not remove cover or back.
1)Read these instructions.
No user-serviceable parts inside. Refer servicing
to qualified service personnel.
3)Heed all warnings.
The lightning flash with arrow-head within a
triangle is intended to tell the user that parts
inside the product are a risk of electric shock
to persons.
The exclamation point within a triangle
is intended to tell the user that important
operating and servicing instructions are in the
papers with the appliance.
WARNING:
To prevent damage which may result in fire or
shock hazard, do not expose this apparatus to
rain or moisture.
Do not place containers with water (flower vase,
cups, cosmetics, etc.) above the set.
(including on shelves above, etc.)
WARNING:
1)To prevent electric shock, do not remove cover. No
user serviceable parts inside. Refer servicing to
qualified service personnel.
2) Do not remove the grounding pin on the power
plug. This apparatus is equipped with a three pin
grounding-type power plug. This plug will only fit
a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the
outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
2)Keep these instructions.
4)Follow all instructions.
5)Do not use this apparatus near water.
6)Clean only with dry cloth.
7)Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8)Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9)Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The
wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the
obsolete outlet.
10)Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11)Only use attachments / accessories specified by the
manufacturer.
12)Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart / apparatus combination
to avoid injury from tip-over.
13)Unplug this apparatus during lightning storms or
when unused for long periods of time.
14)Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15)To prevent electric shock, ensure the grounding pin
on the AC cord power plug is securely connected.
2
English
FCC STATEMENT
This equipment has been tested and found to comply
with the limits for a class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
FCC CAUTION:
To assure continued compliance, follow the attached
installation instructions and use only the provided
power supply cord. Any changes or modifications
not expressly approved by Panasonic Corp. of North
America could void the user’s authority to operate
this device.
Declaration of Verification
Model No.
TH-75BQE1W
Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, New Jersey
07102-5490
Contact Source:
Panasonic System Communications Company of
North America
1-877-655-2357
General Contact:
http://shop.panasonic.com/support
This device complies with Part 15 of the FCC Rules and
all applicable IC RSS standards. Operation is subject
to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation.
CANADIAN NOTICE:
This Class A digital apparatus complies with
Canadian ICES-003.
WARNING:
•• Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/
Data Processing Equipment, ANSI/NFPA 75.
•• For permanently connected equipment, a readily
accessible disconnect device shall be incorporated
in the building installation wiring.
•• For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
Note:
Image retention may occur. If you display a still
picture for an extended period, the image might
remain on the screen. However, it will disappear when
a general moving picture is displayed for a while.
Trademark Credits
•• Microsoft, Windows and Internet Explorer are the
registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other
countries.
•• Macintosh, Mac, Mac OS, OS X and Safari are the
trademarks of Apple Inc. registered in the United
States and other countries.
•• HDMI, High-Definition Multimedia Interface and the
HDMI Logo are trademarks or registered trademarks
of HDMI Licensing Administrator, Inc. in the United
States and other countries.
•• Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
Even if no special notation has been made of company
or product trademarks, these trademarks have been fully
respected.
English
3
Important Safety
Notice
WARNING
1)To prevent damage which may result in fire or
shock hazard, do not expose this appliance to
dripping or splashing.
Do not place containers with water (flower vase,
cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
No naked flame sources, such as lighted candles,
should be placed on / above the set.
If a display is not positioned in a sufficiently stable
location, it can be potentially hazardous due to falling.
Many injuries, particularly to children, can be avoided
by taking simple precautions such as:
•• Using cabinets or stands recommended by the
manufacturer of the display.
•• Only using furniture that can safely support the
display.
•• Ensuring the display is not overhanging the edge
of the supporting furniture.
•• Not placing the display on tall furniture (for
example, cupboards or bookcases) without
anchoring both the furniture and the display to a
suitable support.
2)To prevent electric shock, do not remove cover. No
user serviceable parts inside. Refer servicing to
qualified service personnel.
•• Not standing the displays on cloth or other
3)Do not remove the earthing pin on the power
plug. This apparatus is equipped with a three pin
earthing-type power plug. This plug will only fit an
earthing-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet,
contact an electrician.
•• Educating children about the dangers of climbing
Do not defeat the purpose of the earthing plug.
4)To prevent electric shock, ensure the earthing pin
on the AC cord power plug is securely connected.
CAUTION
This appliance is intended for use in environments
which are relatively free of electromagnetic fields.
Using this appliance near sources of strong
electromagnetic fields or where electrical noise may
overlap with the input signals could cause the picture
and sound to wobble or cause interference such as
noise to appear.
To avoid the possibility of harm to this appliance, keep
it away from sources of strong electromagnetic fields.
WARNING:
This equipment is compliant with Class A of CISPR32.
In a residential environment this equipment may
cause radio interference.
4
IMPORTANT INFORMATION
English
materials placed between the display and
supporting furniture.
on furniture to reach the display or its controls.
Safety Precautions
IMPORTANT: THE MOULDED PLUG
FOR YOUR SAFETY, PLEASE READ THE
FOLLOWING TEXT CAREFULLY.
This display is supplied with a moulded three pin
mains plug for your safety and convenience. A 10
amp fuse is fitted in this plug. Shall the fuse need to
be replaced, please ensure that the replacement fuse
has a rating of 10 amps and that it is approved by
ASTA or BSI to BS1362.
Check for the ASTA mark
the body of the fuse.
or the BSI mark
on
If the plug contains a removable fuse cover, you must
ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used
until a replacement cover is obtained.
A replacement fuse cover can be purchased from
your local Panasonic dealer.
Do not cut off the mains plug.
Do not use any other type of mains lead except the
one supplied with this display.
The supplied mains lead and moulded plug are
designed to be used with this display to avoid
interference and for your safety.
If the socket outlet in your home is not suitable, get it
changed by a qualified electrician.
If the plug or mains lead becomes damaged,
purchase a replacement from an authorized dealer.
WARNING : — THIS DISPLAY MUST BE EARTHED.
How to replace the fuse.
Open the fuse compartment with a screwdriver and
replace the fuse.
WARNING
■■Setup
This LCD Display is for use only with the following
optional accessory.
Use with any other type of optional accessories may
cause instability which could result in the possibility
of injury.
(The following accessory is manufactured by Panasonic
Corporation.)
Please firmly install the Pedestal sold separately.
Installation should be done by a professional vendor.
Work in a team of 4 persons when installing.
Pedestal
•• TY-ST75PE9
Note
● When installing the Pedestal, thoroughly read the
instructions manual included with the product and
correctly install the stand. Make sure to take the fallprevention measures.
● For ensuring safety and performance, ask your
distributor or a professional vendor to carry out the
installation work.
● Please note that we will not be responsible for any
product damage that happens due to defects in the
installation environment of stand or wall-mounting
clasp even if it is within the warranty period.
● For the products that you are no longer using, ask
a professional contractor to promptly remove such
products.
● When installing, “crack in LCD panel” may occur
because of impact etc. Therefore, please carefully
handle the product.
● The part numbers of optional items are subject to
change without notice.
We are not responsible for any product damage, etc.
caused by failures in the installation environment even
during the warranty period.
Always be sure to ask a qualified technician to carry out
set-up.
Small parts can present choking hazard if accidentally
swallowed. Keep small parts away from young children.
Discard unneeded small parts and other objects,
including packaging materials and plastic bags/sheets to
prevent them from being played with by young children,
creating the potential risk of suffocation.
Do not place the Display on sloped or unstable
surfaces, and ensure that the Display does not hang
over the edge of the base.
•• The Display may fall off or tip over.
Install this unit at a location with minimal vibration
and which can support the weight of the unit.
•• Dropping or falling of the unit may cause injury or
malfunction.
English
5
Do not place any objects on top of the Display.
•• If foreign objects or water get inside the Display, a
short-circuit may occur which could result in fire or
electric shock. If any foreign objects get inside the
Display, please consult your local Panasonic dealer.
Transport only in upright position!
•• Transporting the unit with its front panel facing upright
or downward may cause damage to the internal
circuitry.
Ventilation should not be impeded by covering
the ventilation openings with items such as
newspapers, table cloths and curtains.
For sufficient ventilation, see page 9.
Caution - For use only with UL Listed Wall Mount
Bracket with minimum weight/load 68.0
(150.0 lbs).
When installing the Display vertically;
When installing the Display vertically, be sure that
the Power Indicator comes to the downside. Heat is
generated and it may cause fire or damage to the
Display.
■■When using the LCD Display
The Display is designed to operate on 110 – 240 V
AC, 50/60 Hz.
Do not cover the ventilation holes.
•• Doing so may cause the Display to overheat, which
can cause fire or damage to the Display.
Do not stick any foreign objects into the Display.
•• Do not insert any metal or flammable objects into the
ventilations holes or drop them onto the Display, as
doing so can cause fire or electric shock.
Do not remove the cover or modify it in any way.
•• High voltages which can cause severe electric shocks
are present inside the Display. For any inspection,
adjustment and repair work, please contact your local
Panasonic dealer.
Ensure that the mains plug is easily accessible.
The mains plug shall be connected to a mains
socket outlet with a protective earthing connection.
Do not use any power supply cord other than that
provided with this unit.
•• Doing so may cause short-circuit, generates heat,
etc., which could cause electric shock or fire.
Do not use the supplied power supply cord with any
other devices.
•• Doing so could cause electric shock or fire.
Securely insert the power supply plug as far as it
will go.
•• If the plug is not fully inserted, heat may be generated
Power indicator
Cautions for Wall or Pedestal Installation
•• The installation should be performed by an installation
professional. Installing the Display incorrectly may
lead to an accident that results in death or serious
injury. Use the optional Pedestal. (see page 5)
•• When installing on a wall, a wall hanging bracket that
conforms to VESA standards must be used.
75-inch model : VESA 400 × 400
(see page 9)
•• Before installation, be sure to check if the mounting
location has enough strength to support the weight
of the LCD display and the wall hanging bracket for
anti drop.
•• If you terminate the use of the Display on the Wall or
Pedestal, ask a professional to remove the Display as
soon as possible.
which could cause fire. If the plug is damaged or the
wall socket is loose, they shall not be used.
Do not handle the power supply plug with wet
hands.
•• Doing so may cause electric shocks.
Do not do anything that may damage the power
cable. When disconnecting the power cable, pull on
the plug body, not the cable.
•• Do not damage the cable, make any modifications
to it, place heavy objects on top of it, heat it, place it
near any hot objects, twist it, bend it excessively or
pull it. To do so may cause fire and electric shock. If
the power cable is damaged, have it repaired at your
local Panasonic dealer.
Do not touch the power supply cord or the plug
directly by hand when they are damaged.
•• Electric shock could occur.
Do not remove covers and NEVER modify the
Display yourself.
•• When mounting the Display on the wall, prevent the
•• Do not remove the rear cover as live parts are
Do not install the product to a place where the
product is exposed to direct sunlight.
•• Have the Display checked, adjusted, or repaired at
mounting screws and power cable from contacting
metal objects inside the wall. An electric shock may
occur if they contact metal objects inside the wall.
•• If the unit is exposed to direct sunlight even indoors,
the temperature rise of the liquid crystal panel may
cause malfunction.
accessible when it is removed. There are no user
serviceable parts inside. (High-voltage components
may cause serious electrical shock.)
your local Panasonic dealer.
Keep the screws (supplied) out of reach of children.
If accidentally swallowed, it will be harmful to the
body.
•• Please contact a doctor immediately in case you
doubt that the child may have swallowed it.
6
English
When using the unit in an area where there are
passers-by, do not connect the USB cable for the
touch panel to the PC.
Doing so may cause them to bump into the unit, or their
feet may be entangled in the USB cable, resulting in a
fire, electric shock or injury.
•• When using the unit in an area where there are
passers-by, provide an enclosure around the unit to
prevent people from approaching it.
If the Display is not going to be used for any
prolonged length of time, unplug the power supply
plug from the wall outlet.
Picture noise may occur if you connect / disconnect
the cables connected to the input terminals you
are currently not watching, or if you turn the power
of the video equipment on / off, but it is not a
malfunction.
To prevent the spread of fire, keep
candles or other open flames away from
this product at all times.
CAUTION
If problems or malfunction occur, stop using
immediately.
■■If problems occur, unplug the power supply
plug.
•• Smoke or an abnormal odour come out from the unit.
•• No picture appears or no sound is heard,
occasionally.
•• Liquid such as water or foreign objects got inside the
unit.
•• The unit has deformed or broken parts.
If you continue to use the unit in this condition, it
could result in fire or electric shock.
•• Turn the power off immediately, unplug the power
supply plug from the wall outlet, and then contact the
dealer for repairs.
•• To cut off the power supply to this Display completely,
you need to unplug the power supply plug from the
wall outlet.
•• Repairing the unit yourself is dangerous, and shall
never be done.
•• To enable to unplug the power supply plug
immediately, use the wall outlet which you can reach
easily.
■■Do not touch the unit directly by hand when
it is damaged.
Electric shock could occur.
■■When using the LCD Display
Do not bring your hands, face or objects close to the
ventilation holes of the Display.
•• Heated air comes out from the ventilation holes at the
top of Display will be hot. Do not bring your hands or
face, or objects which cannot withstand heat, close to
this port, otherwise burns or deformation could result.
4 people are required to carry or unpack this unit.
•• If this is not observed, the unit may drop, resulting in
injury.
Always work in a team of 4 persons when attaching
or removing the speakers supplied in the accessory.
•• The display unit may fall down and it may cause
injury.
Be sure to disconnect all cables and overturn
prevention accessories before moving the Display.
•• If the Display is moved while some of the cables are
still connected, the cables may become damaged,
and fire or electric shock could result.
Do not apply too much force or impact shock.
•• The front panel may crack, resulting in injury.
Disconnect the power supply plug from the wall
socket as a safety precaution before carrying out
any cleaning.
•• Electric shocks can result if this is not done.
English
7
Clean the power cable regularly to prevent it
becoming dusty.
•• If dust built up on the power cord plug, the resultant
humidity can damage the insulation, which could
result in fire. Pull the power cord plug out from the
wall outlet and wipe the mains lead with a dry cloth.
Do not step on, or hang from the display or the
Pedestal.
•• They might tip over, or might be broken and it may
result in injury. Pay special attention to the children.
Do not reverse the polarity (+ and -) of the battery
when inserting.
•• Mishandling the battery may cause its explosion
or leakage, resulting in fire, injury or damage to
surrounding properties.
•• Insert the battery correctly as instructed. (see page
12)
Do not use batteries with the outer cover peeling
away or removed.
(The outer cover is attached to the battery for safety.
It must not be removed. Doing so may cause short
circuits.)
•• Mishandling the batteries may cause the batteries
to short circuit, resulting in fire, injury or damage to
surrounding properties.
Remove the batteries from the remote control
transmitter when not using for a long period of time.
•• The battery may leak, heat, ignite or burst, resulting in
fire or damage to surrounding properties.
Do not burn or breakup batteries.
•• Batteries must not be exposed to excessive heat such
as sunshine, fire or the like.
Do not turn the Display upside down.
Do not position the unit with its liquid crystal panel
facing upright.
Parts of the unit become hot.
•• Even when the temperature of parts of the front panel
surface, top and rear of the unit has risen, these
temperature rises will not pose any problems in terms
of performance or quality.
8
English
Precautions for use
About the screws used when using a wall hanging
bracket that conforms to VESA standards
Cautions when installing
Inch
model
Screw pitch for
installation
Depth of
screw
hole
Screw
(quantity)
Do not set up the Display outdoors.
75
400 mm × 400 mm
25 mm
M6 (4)
•• The Display is designed for indoor use.
Install this unit at a location which can support the
weight of the unit.
•• Use the installation bracket that conforms to VESA
standards
Environmental temperature to use this unit
•• When using the unit where it is below 1 400 m
(4 593 ft) above sea level: 0 °C to 40 °C (32 °F to
104 °F)
•• When using the unit at high altitudes (1 400 m
(4 593 ft) and higher and below 2 800 m (9 186 ft)
above sea level): 0 °C to 35 °C (32 °F to 95 °F)
Do not install the unit where it is 2 800 m (9 186 ft)
and higher above sea level.
•• Failure to do so may shorten the life of the internal
Be careful of the movable structure of the power
indicator and remote control sensor.
•• As factory default, the power indicator and remote
control sensor are stored in the main unit. In
normal cases, pull the remote control sensor box
from the end face of the unit until it gets locked at
the designated position. Depending on the setup
condition such as when using the multi display, store
the remote control sensor in the main unit. (see page
21)
Depending on the temperature or humidity
conditions, uneven brightness may be observed.
This is not a malfunction.
•• This unevenness will disappear while applying current
continuously. If not, consult the distributor.
parts and result in malfunctions.
We are not responsible for any product damage, etc.
caused by failures in the installation environment
even during the warranty period.
Do not place the display where it may be affected by
salt or corrosive gas.
•• Failure to do so may shorten the life of the internal
parts and result in malfunctions due to corrosion.
Required space for ventilation
•• When using the Pedestal (optional accessory), leave
a space of 10 cm (3 15/16”) or more at the top, left and
right, and 5 cm (1 31/32”) or more at the rear, and also
keep the space between the bottom of the display
and the floor surface.
If using some other setting-up method (wall-hanging,
etc.), follow the manual of it. (If there is no specific
indication of installation dimension in the installation
manual, leave a space of 10 cm (3 15/16”) or more at
the top, bottom, left and right, and 5 cm (1 31/32”) or
more at the rear.)
Minimum distance:
a
a
a
b
a: 10 cm
(3 15/16”)
b: 5 cm
(1 31/32”)
•• Operation of this unit is guaranteed up to an ambient
temperature of 40 °C (104 °F). When installing the
unit in a case or chassis, be sure to provide adequate
ventilation with a cooling fan or ventilation hole so
that the surrounding temperature (inside the case or
chassis) including the temperature of the front surface
of the liquid crystal panel can be kept at 40 °C
(104 °F) or less.
English
9
Cleaning and maintenance
First, remove the mains plug from the mains socket.
The front panel surface has been specially treated.
Wipe the surface of the front panel gently using only
a cleaning cloth or a soft, lint-free cloth.
•• If the surface is particularly dirty, wipe with a soft,
lint-free cloth which has been soaked in pure water or
water in which neutral detergent has been diluted 100
times, and then wipe it evenly with a dry cloth of the
same type until the surface is dry.
Wipe off dirt on the IR transmission part with soft
cloth.
•• Wipe off dirt on the IR
IR transmission
transmission part with soft
part
cloth once a day.
If malfunction is due to dirt
on the IR transmission part,
simply wiping it off lightly can
recover the performance.
If dirt is sticky, wipe it off with cloth wrung out of
neutral detergent diluted with water and then wipe the
part with dry cloth.
•• If the substance such as the material of the supplied
pen is stuck on the glass surface, wipe it with a wet
cloth.
Note that if a deep scratch is caused by using objects
other than the supplied pen, it may not be wiped off.
•• Do not scratch or hit the surface of the front panel
with fingernails or other hard objects, otherwise the
surface may become damaged. Furthermore, avoid
contact with volatile substances such as insect
sprays, solvents and thinner, otherwise the quality of
the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry
cloth.
•• If the cabinet is particularly dirty, soak the cloth in
water to which a small amount of neutral detergent
has been added and then wring the cloth dry. Use this
cloth to wipe the cabinet, and then wipe it dry with a
dry cloth.
•• Do not allow any detergent to come into direct contact
with the surface of the Display. If water droplets get
inside the unit, operating problems may result.
•• Avoid contact with volatile substances such as insect
sprays, solvents and thinner, otherwise the quality of
the cabinet surface may be adversely affected or the
coating may peel off. Furthermore, do not leave it for
long periods in contact with articles made from rubber
or PVC.
Usage of a chemical cloth
•• Do not use a chemical cloth for the panel surface.
•• Follow the instructions for the chemical cloth to use it
for the cabinet.
10
English
Touch panel
Carefully observe the following instructions as the
display has an optical touch panel.
Do not expose the display to direct sunlight or
strong light source during use.
•• Otherwise malfunction may occur since the optical
touch panel of the display uses infrared rays.
Always use a finger or the supplied pen to operate
the touch panel. Do not use a hard or sharp tip such
as nail, ball-point pen, and pencil.
When using any other infrared device, keep a
distance to prevent erroneous operation.
Disposal
When disposing the product, ask your local
authority or dealer about the correct methods of
disposal.
Introduction
Checking the accessories
Check that you have all accessories.
□Operating Instructions
□Clamper × 3
● DPVF1697ZA
□Speaker × 1
● DPVF1698ZA
(CD-ROM × 1)
□Speaker
Mounting Clasp × 2
● DPVF1709ZA (Left)
□Power Supply Cord
(Approx. 2 m)
● 1JP155AF1U
● DPVF1710ZA (Right)
(Right)
(Left)
(These clasps are assembled with the speaker and
supplied with it.)
□Screw for Mounting the
Speaker (M3) × 4
● DPVF1701ZA
● 1JP155AF1W
□Speaker Cable × 2
(Approx. 0.7 m)
● DPVF1702ZA
● 2JP155AF1W
Attention
● 3JP155AF1W
● Store small parts in an appropriate manner, and keep
them away from young children.
● The part numbers of accessories are subject to
change without notice.
(The actual part number may differ from the ones
shown above.)
□Remote Control × 1
● DPVF1671ZA
● In case you have lost accessories, please purchase
them from your dealer. (Available from the customer
service)
● Dispose the packaging materials appropriately after
taking out the items.
□Batteries for the Remote
Control Transmitter × 2
(AA/R6/LR6 type)
□Pen × 1
● TKR5ZA45001
English
11
Remote Control Batteries
Open the battery cover.
AA/R6/LR6 type
Note
Insert batteries and close
the battery cover.
(Insert starting from the
side.)
● Incorrect installation of the batteries can cause
battery leakage and corrosion that will damage the
remote control.
● Disposal of batteries should be done in an
environment-friendly manner.
Take the following precautions.
1. Batteries shall always be replaced as a pair.
2.Do not combine a used battery with a new one.
3.Do not mix battery types (example; manganese
dioxide battery and alkaline battery etc.).
4.Do not attempt to charge, disassemble, or burn used
batteries.
5.Do not burn or breakup batteries.
Moreover, batteries must not be exposed to excessive
heat such as sunshine, fire or the like.
12
English
Names and functions of parts
■■Button and indicator
Back side
Control button
1
2
3
4
5
6
7
1
[MENU] button
It shows the on-screen display (OSD) menu.
2
[INPUT] button
It shows the OSD menu and changes the input source.
3
Plus (+) button
It increases the volume.
4
Minus (−) button
It lowers the volume.
5
Up (▲) button
It moves up the item highlighted in the OSD menu.
6
Down (▼) button
7
[POWER] button (
You can select [HDMI1], [HDMI2], [DVI-D], [PC], and [USB] with the up (▲) /
down (▼) buttons.
It moves down the item highlighted in the OSD menu.
)
It turns ON/OFF the power supply. This button cannot be operated when the
power indicator is turned off. In this case, turn on the Main power switch. (see
page 14)
English
13
Back side
2
2
Base
2
1
14
1
Main power switch
It turns “Off ( ) / On ( )” the main power supply. It is used for starting /
stopping power supply to the device.
2
Hole for cable clamp
installation
It is used for fastening cable with the main unit.
English
Cable and terminal
Back side
6
7
8
14
9
10
11
EXT SP
1
12
5
(8Ω,20W [10W+10W])
13
Base
2
3
4
1 Hole for installing
It is used for security and theft prevention.
5 Remote control
It is connected with the power supply cord provided in accessories. For Class I products, it
is mandatory to connect the main power supply having earthing.
It is used for connecting to a PC for controlling the main unit.
It is an IR input terminal that is connected with an IR cable. Please contact your distributor
for purchasing an IR cable.
Remote control sensor:It receives signals from the remote control.
theft prevention
lock
2 AC IN (3-pin, with
earthing terminal)
3 SERIAL IN
4 IR IN
sensor /
Power indicator
6 USB
7 AUDIO OUT
8 AUDIO IN
9
10
11
12
13
PC IN
DVI-D IN
HDMI 2
HDMI 1
EXT SP
Power indicator:It shows the status of LCD display.
It is a USB input terminal for USB flash drives.
This terminal is for connecting a speaker having amplifier. It will output audio when [AUDIO
OUT] is specified in [Sound] - [Output Select]. Output can be adjusted with the [VOL] button
(+/−) of the remote control.
It is used for connecting audio output cables of external devices such as PC, VCR, and
DVD player. For HDMI input, you can select [AUDIO IN] in [Sound] - [Audio Source].
[AUDIO IN] is default in DVI-D/PC input.
It is used for connecting with the analogue video signal output terminal of a PC.
It is connected with a digital video signal output terminal such as a PC.
It is used for connecting with a device compatible with audio / video signal of HDMI interface.
It is used for connecting with a device compatible with audio / video signal of HDMI interface.
It is connected with L/R and +/− terminal of the speaker provided as accessory.
It will output audio when [EXT SP] is specified in [Sound] - [Output Select]. Output can be
adjusted with the [VOL] button (+/−) of the remote control.
14 USB cable for
touch panel
It is connected to a PC's USB terminal for using the touch panel.
English
15
Remote control
1 [POWER]
It turns ON/OFF the power supply. Remote
control cannot be operated when the power
indicator is turned off.
2 [AUTO ADJUST]
It shows the automatic adjustment selection
menu during PC input.
3 [PICTURE STYLE]
It shows the settings menu of the image
mode for the displayed input.
4 [SOUND STYLE]
It shows the settings menu of the audio mode
for the displayed input.
5 [PICTURE]
It shows the image settings menu for the
displayed input.
6 [SOUND]
It shows the audio settings menu for the
displayed input.
7 [SET UP]
It shows the [Setup] menu.
8 [ASPECT]
It shows the settings menu of aspect ratio.
9 [MENU]
It turns ON/OFF the OSD menu.
10 [RETURN]
It is used for going back to the previous menu
screen.
11 Cursor buttons
They are used for operating the menu screen.
12 [OK]
It is used for selecting menu items.
13 [EXIT]
It turns OFF the OSD menu.
14 [INFO]
It shows the selected input source.
3
4
7
8
10
12
1
2
5
6
9
11
14
13
15
17
16
19
21
22
18
20
23
25
24
15 [MEDIA CONTROL] It provides various control functions of a specific menu. Function of each button will appear
in OSD in the colour of the respective button.
16 [VOL]
Pressing the plus (+) side will increase the audio output level.
17 [SLEEP]
It adjusts the sleep timer.
18 [MUTE]
It mutes the audio. Press once again to unmute.
19 [INPUT]
It is used for changing the input source.
20 [HDMI]
It is used for selecting HDMI input.
21 [DVI]
It is used for selecting DVI-D input.
22 [PC]
It is used for selecting PC input.
23 Media operation
It provides control functions when a media file is playing. Rewind (
Fast forward (
), Previous (
), Stop ( ), Pause ( ), Next (
24 [USB]
It is used for selecting USB input.
25 [−]
Not supported in this device.
button
16
English
Pressing the minus (−) side will decrease the audio output level.
Turning off the power supply and changing the volume level will restore the audio.
), Play ( ),
).
Installation
Connecting and fixing the power
supply cord
Back side of the unit
Fixing the connection cables
Note
● Three clampers are provided as accessories with
the device. When not using the touch panel, use one
of the clampers to fix the USB cable for touch panel
at the position of A. Moreover, with the other two
clampers, fix the other cables at the position of B. If
you wish to purchase clampers, please contact your
dealer. (Available from the customer service)
A
Fixing the power supply cord
B
B
B
B
1. Mounting the clampers
Mounting hole
Power supply cord (supplied)
Insert the convex part in the
mounting hole.
Insert the connector in the main unit
Insert until you hear the clicking sound.
Note
● Check that both sides are locked.
When removing the power supply cord
Note
● Once you mount the clampers in the clamper
mounting holes, you will not be able to remove them.
2. Bundling the cables
Pass the band and
pull it.
Loosening the band
Pull the tip of the band
while pressing the
knob.
Remove while pressing the knobs located next to the
connector.
Note
● When removing the power supply cord, make sure
to first remove the power supply plug on the power
socket side.
● The power supply cord provided in the accessories is
for exclusively using with the device. Do not use it for
any other purpose.
Knob
English
17
Using the touch panel
1
2
3
4
Turn off the Main power switch of the display.
Connect the computer and the USB cable of the display.
Connect the computer and the video input terminal of the display.
Turn on the Main power switch of the display. If required, press the [POWER] button of the remote control to turn
on the display.
■■Display settings
Please make the following display settings.
•• Switch the input signal to the video input from the computer.
•• Set the screen position such that the computer’s screen correctly appears on the display.
A
A
A
A
A
(Approx. 2 m)
USB
TYPE A
A: Infrared transmitting part
Computer
Note
● Pulling the USB cable with excessive force may result in the breakdown of the touch panel. Therefore, handle it
carefully.
● For preventing disconnection of the USB cable for touch panel, fix it with the device by using the clamper. (see page
17)
● Wipe off dirt on the infrared transmitting part with a soft cloth.
Wipe off dirt on the infrared transmitting part with a soft cloth once in a day. When a defect has occurred because of
dirt on the infrared transmitting part, lightly wiping it will restore the function. If the infrared transmitting part is heavily
soiled, dip the cloth in a neutral cleaning agent diluted with water and firmly squeeze it. Use this cloth and gently
clean the infrared transmitting part. Finally, wipe it with a dry cloth.
Using WhiteBoard software
WhiteBoard software allows you to use various functions, for example, you can capture documents and pictures, draw
with pen, etc.
18
1
Obtain the WhiteBoard software (Windows / Mac) from the support site below.
2
For details of operation, refer to the manual of WhiteBoard software on the site above.
https://panasonic.net/cns/prodisplays/
English
Mounting sequence of the speaker
Mount the speaker (supplied).
A cross slot screw driver is required for assembling. Therefore, arrange it in advance.
1
Preparing the display
Work in a team of 4 persons when installing.
Spreading out a soft cloth, etc., place the display with the screen facing down.
● Be careful not to damage the display screen, for example, by dragging it.
● When placing the display with the screen facing down, or lifting it up, never hold or put pressure on the front
panel. Inside of the front panel may be damaged.
2
As shown in the figure below, mount the speaker on the display.
Fix the speaker with 2 speaker mounting clasps and 4 speaker mounting screws (supplied).
Tightening torque: 0.5 to 0.8 N•m
Note
● Speaker mounting clasps are assembled with the speaker and supplied with it.
■■In the case of lateral placement
Speaker
Screws for mounting the speaker
(M3)
*Fix the opposite side in the symmetric position.
■■In the case of vertical placement
*This side is the top side
of the unit.
Screws for mounting the speaker (M3)
Speaker
*Fix the opposite side in the symmetric position.
English
19
3
Connecting the speaker cables
With the 2 speaker cables (supplied), connect the EXT SP terminal of the display and the speaker.
Note
● Connect the R terminal on the display to the R terminal on the speaker, and the same applies for the L terminals
on them.
● Connect the red terminal on the display to the red terminal on the speaker, and the same applies for the black
terminals on them.
● When connecting the speaker cable, please take precaution so that short circuit doesn’t happen in the core
wire.
1.While pushing the lever
1. Pushing down the lever
2.Insert the cable
3.Release the
lever
2.Insert the cable
3. Return the lever
EXT SP
(8Ω,20W [10W+10W])
R
L
Mount the clamper (supplied) at the following places, and then fix the cable.
When the cable is long, bundle and fix the cable using this clamper.
20
English
Operation
Turn on the power supply of all connected devices
1
2
Turn on the power supply of all connected devices such as PC and DVD player.
Set the remote control sensor.
Before using the remote control, decide the position of remote control sensor of LCD display.
Remote control sensor is the small black box located on the left side of the back of LCD display. Until the sensor
gets locked at the designated position, push the position of A with thumb etc. and slide it in the downward direction
(refer to bottom right of the illustration).
Follow these steps in the opposite order for returning the sensor to its original position.
A
When the remote control
sensor is stored
When the remote control
sensor is used
English
21
3
Turn on the Main power switch.
The power indicator will light up, and you can now operate remote control and control buttons on the back side,
avail serial control, and enable the scheduler.
When the Main power switch is off (power indicator is light out), control buttons on the back side, remote control,
and the settings of scheduler will not work. For using these, check that the Main power switch is on (power
indicator has light up).
Main power switch
4
22
Turn on the device.
Press the [POWER] button located on the left side of the device, or the [POWER] button located on top left of the
remote control.
English
Specifications
Main unit
Model No.
TH-75BQE1W
Type
Touch screen LCD display
Power source
110 ‒ 240 V ~ (110 ‒ 240 V alternating current), 50/60 Hz
Power consumption
Power off with the Main power switch: approx. 0 W
370 W
Power off with the remote control: approx. 0.5 W
VA panel (Direct LED backlight)
LCD display panel
75-inch model (16:9 aspect ratio)
1 650 mm (W) × 928 mm (H) × 1 893 mm (diagonal) /
Screen size
64.9” (W) × 36.5” (H) × 74.5” (diagonal)
Number of pixels
8 294 400 pixels (3 840 (horizontal) × 2 160 (vertical))
Operating condition
Temperature: 0 °C ‒ 40 °C (32 °F ‒ 104 °F)*1 Humidity: 20 % ‒ 80 % (no condensation)
Storing condition
Temperature: -20 °C ‒ 60 °C (-4 °F ‒ 140 °F) Humidity: 20 % ‒ 80 % (no condensation)
HDMI input terminal
HDMI 1 / HDMI 2
Digital RGB input
terminal
DVI-D IN
PC input terminal
PC IN
Audio input terminal
AUDIO IN
TYPE A Connector*2 × 2
Audio signal: Linear PCM (sampling frequencies - 48 kHz, 44.1 kHz, 32 kHz)
DVI-D 24 Pin × 1
Mini D-sub 15 Pin (Compatible with DDC2B) × 1
R/G/B
0.7 Vp-p (75 Ω) (without sync signal)
HD/VD
TTL
Stereo mini jack (M3) × 1, 0.5 Vrms, shared with DVI-D IN and PC IN
Audio output terminal Stereo mini jack (M3) × 1, 0.5 Vrms
AUDIO OUT
Serial input terminal
SERIAL IN
External speaker
terminal
EXT SP
IR input terminal
IR IN
USB flash drive
terminal
USB
Output: Variable (-∞ ‒ 0 dB) (1 kHz 0 dB input, 10 kΩ load)
External Control Terminal
D-sub 9 Pin × 1
RS-232C compatible
8Ω, 20 W [10 W + 10 W] (10 % THD)
Stereo mini jack (M3) × 1
TYPE A USB connector × 1
DC 5V / 1A (USB 3.0 is not supported.)
1 710 mm × 989 mm × 102 mm / 67.3” × 39.0” × 4.02”
Outer dimensions
(W × H × D)
Mass
Cabinet material
1 710 mm × 1 072 mm × 102 mm / 67.3” × 42.3” × 4.02” (horizontal installation /
when the speaker mounted)
989 mm × 1 793 mm × 102 mm / 39.0” × 70.6” × 4.02” (vertical installation /
when the speaker mounted)
Approx. 66.0
/ 145.5 lbs (Approx. 68.0
/ 150.0 lbs when the speaker mounted.)
Front: metal / Back cover: metal
English
23
Remote control
Power source
DC 3 V (battery (AA/R6/LR6 type) × 2)
Operating range
Approx. 5 m (from the front of the remote control sensor)
Mass
Approx. 113 / 0.3 lbs (including batteries)
Outer dimensions
(W × H × D)
160 mm × 50 mm × 20 mm / 6.3” × 2.0” × 0.8”
Speaker
Impedance
8Ω
Rated input
20 W [10 W + 10 W]
Outer dimensions
(W × H × D)
Mass
Cabinet material
763 mm × 82 mm × 59 mm / 30.1” × 3.3” × 2.4”
Approx. 2.0
/ 4.4 lbs
Resin
*1Environmental temperature to use this unit at high altitudes (1 400 m (4 593 ft) and higher and below 2 800 m
(9 186 ft) above sea level): 0 °C to 35 °C (32 °F to 95 °F)
*2VIERA LINK is not supported.
24
English
Panasonic Professional Flat Panel Display Limited Warranty
(for the U.S.A and Puerto Rico)
Panasonic Solutions Company
Unit of Panasonic Corporation of
North America
Two Riverfront Plaza, Newark,
New Jersey 07102-5490
Panasonic Professional Flat Panel Display
Limited Warranty
Panasonic Solutions Company. (referred to as “the
Warrantor”) will repair this product and all included
accessories with new or refurbished parts, free of
charge in the USA or Puerto Rico, of the original
purchase in the event of a defect in materials or workmanship as follows:
Models or Parts
Part
Warranty
Professional Flat
Panel Display
2 Years
Labor
Warranty
2 Years
On-site or carry-in service in the USA and Puerto Rico
may be obtained during the warranty period by contacting
Panasonic Solutions Company Service toll free at
1-877-655-2357.
This warranty is extended only to the original purchaser
and is non transferable. A purchase receipt or other
proof of date of original purchase will be required before
warranty service is rendered.
This warranty only covers failures due to defects in
materials or workmanship, which occur during normal
use. The warranty does not cover damage which occur
in shipment, or failures which are caused by products
not supplied by the warrantor, or failures which result
from improper installation, set-up adjustments, improper
antenna, inadequate signal pickup, maladjustment of
consumer controls, improper operation, power line surge,
improper voltage supply, lighting damage, or service by
anyone other than an authorized repair facility, or
damage that is attributable to acts of God.
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING, WITHOUT LIMITION, DAMAGE
TO DISCS) RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF
THE WARRANTY. ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH
ABOVE.
Some states do not allow the exclusion or limitation
of incidental or consequential damages, or limitations
on how long an implied warranty lasts, so the above
exclusions or limitations may nor apply to you. This
warranty gives you specific legal rights and you may
other rights, which vary from state to state.
If you have a problem with this product that is not
handled to your satisfaction, then write the Consumer
Affairs Department at the Company address indicated
above.
In the USA and Puerto Rico
FOR SERVICE
CALL TOLL FREE
1-877-655-2357
English
25
LIMITED WARRANTY STATEMENT
(for Canada)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
Item
Video Tape
P2/SD Cards
Video Heads
D5 Video heads
Maintenance Items
Colour Camera CCD
Imaging Block
All LCD Monitors
* DLP™ Projectors
* LCD Projectors above
2,500 ANSI Lumens
* LCD Projectors below
2,500 ANSI Lumens
Projector Lamps
All Plasma displays
1 year or 1,000 hrs.
Whichever comes first
90 days
2 years
Labour
N/A
N/A
1 year or 2,000 hrs.
Whichever comes first
1 year or 1,000 hrs.
Whichever comes first
90 days
2 years
3 years
1 year
2 years
2 years (burn-in not covered)
3 years or 17,000 hrs.
3 years or 17,000 hrs.
Whichever comes first
Whichever comes first
3 years or 2,500 hrs.
3 years or 2,500 hrs.
Whichever comes first.
Whichever comes first
3 years or 1,500 hrs.
3 years or 1,500 hrs.
Whichever comes first
Whichever comes first
50% of the rated lamp life or 1 year. 50% of the rated lamp life or 1 year.
Whichever comes first.
Whichever comes first
2 years (burn-in not covered)
2 years
3 years (burn-in not covered)
1 year plus balance (if any) of
the original Manufacturer’s
Limited Warranty.
(Content not covered)
• Dust, smoke, rental/staging environment and twenty-four/seven operation,
dramatically decreases the interval between performances of routine preventive
maintenance required to maintain this warranty coverage.
103 inch Plasma displays
Hard Drive Disk Unit
Parts
30 days—Replacement only
(content not covered)
(Content not covered)
1 year or 2,000 hrs. (prorated)
Whichever comes first
WARRANTY COVERAGE PERIOD EXCEPTIONS
LIMITED WARRANTY STATEMENT
Panasonic Canada Inc. (also known as PCI) warrants this product to be free of
defects in material and workmanship under normal use during the applicable
warranty coverage period described below. PCI agrees to repair, or at its option,
exchange, any part that becomes defective. However, the product must be
purchased and serviced in Canada. The product or part that shows evidence of
defect must be delivered prepaid or carried in to an authorized Panasonic Broadcast
Service Center. This warranty does not cover shipping costs.
The warranty coverage period is one year for both parts and labour beginning with
the date of original end user purchase, subject to the exceptions as stated below.
Repaired or replacement parts supplied during the warranty coverage period carry
the unexpired portion of the original warranty coverage period. Proof of product
purchase is a condition of warranty service. The owner must produce the product
purchase receipt or other satisfactory evidence of date of original purchase.
This warranty does not apply to external appearance items, such as handles, knobs,
safety windows, etc. This warranty does not apply to any part, or parts, of the
product, installed, altered, repaired or misused in any way that, in the opinion of PCI,
affects the reliability of or detracts from the performance of the product.
For products requiring routine preventive maintenance, that maintenance must be
performed in order to maintain warranty coverage.
Serial numbers that have been altered, defaced or removed void this warranty. This
warranty does not cover replacements or repairs necessitated by loss or damage
resulting from any cause beyond the control of PCI.
Marking or retained images (sometimes called “burn-in”) resulting from the display of
fixed images on video display products are not defects and are not covered under
this warranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or the exclusion of implied warranties, so the
above limitations and exclusions may not be applicable.
Warranty Service
If the product needs to be shipped for service, carefully pack (preferably in the
original carton) and enclose a letter, detailing the complaint. Send prepaid and
adequately insured to the local authorized Panasonic Service Centre in your
area or to Panasonic Technical Support and Product Services Department, 5770
Ambler Drive, Mississauga, Ontario, L4W 2T3. Shipping to the latter location
requires a return authorization before shipment. No liability is assumed for loss
or damage to the product while in transit.
English
26
Customer Service
English
27
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take
them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any
potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
EU
Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case it complies with
the requirement set by the Directive for the chemical involved.
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union.
If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of
disposal.
Notice (U.S.A. only)
Disposal may be regulated in your community due to environmental considerations. For disposal or
recycling information, please visit Panasonic website:
http://www.panasonic.com/environmental
or call 1-888-769-0149.
Customer’s Record
The model number and serial number of this product may be found on its rear panel. You should note this serial
number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of
your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number
Serial Number
Panasonic System Communications Company of North America
Unit of Panasonic Corporation of North America
Executive Office :
Two Riverfront Plaza, Newark, New Jersey 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive
Mississauga, Ontario
L4W 2T3
Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
English
Web Site: http://panasonic.com
© Panasonic Corporation 2017
DA0717TS0 -PB
Printed in China
Download PDF
Similar pages