Øglaend System ETIN tubing clamps and the SPBE cable tray “snap

Help
Øglaend System ETIN tubing clamps
and the SPBE cable tray
“snap-together”
in no time
?
ETIN tubing clamps give 60-70% cost savings!
P
A
G
E
The ETIN Tubing Clamp is patented.
Manufactured by Øglaend System of Norway.
MINIMAL MOUNTING TIME
3 PARTS PER TUBING PAIR
FRONT-MOUNTED
Clamps for instrument tubing
(process/hydraulic/pneumatic).
Designed for inexpansive, easy and time-saving
assembly based on “press-lock” principle.
Adapted to Øglaend System cable trays type SPBE,
can also be mounted on type SPB
and the ladders LOE (light and medium duty)
and OE (heavy duty).
BACK TO
PLEASE SEE FOLLOWING PAGES FOR FURTHER DETAILS
CATALOGUE
Øglaend System
ETIN clamp - can be
front-mounted by one hand!
1. CLIP THE CLAMP
The clip secures the clamp to the tray. A great advantage when mounting on walls or ceilings.
Disassembling/moving is equally easy. The triangular
shape of the clip-holders prevents breakage of clip
arms.
P
2. PRESS-LOCK TUBING
Press tubing into place in the clamp. The recess in
the clamp jaw closes around the tubing and takes
over the securing function. The tubing is kept isolated
from the steel jacket of the clamp, whether using a
single clamp with cover or twin clamps with cover.
A
G
E
3. CLIP OVER TIGHT
Clip on the clamp cover in the same way as the
clamp. The unit is now ready for permanent securing
using the ETIN clamp’s self-locking, through-bolt.
4. SELF-LOCKING BOLT
The tie bolt comes with a lock nut, ready for assembly.
Put the specially designed head down through the
centre hole. It will lock the clamp to the tray at the
same time as the lock nut is tightened.
Disassembly is done just as easily: loosen the nut and
withdraw the bolt by twisting it the opposite direction.
BACK TO
THE ONLY TOOL YOU NEED IS A
10MM SPANNER
CATALOGUE
Major assembly work
is even easier.
E.g.: 8 tubes = 8 parts!
EFFICIENCY INCREASES
WITH AMOUNT OF WORK
The illustrations show the efficiency of the clamp when
mounting large numbers of tubes. The ETIN clamp
mounted on SPBE trays provides maximum use of space.
An improved hole pattern without dead zones means that
the entire width of the tray can be used. For greater
widths and mounting of many tubes, front-mounting of
the ETIN clamp has many advantages and give you a
considerably financial gain. The parts are the same. All
you need to remember is:
Two different bolts, one cover per bolt, one clamp per
tubing pair, and the tubing dimension.
ETIN CLAMPS ARE MANUFACTURED IN
ACID-RESISTING STEEL AND PLASTIC
The clamp’s material composition and design combine
easy mounting with good attachment (press-lock).
A stainless spring steel jacket encloses a flexible plastic
jaw. The plastic material absorbs noise and vibration, has
a high melting point and is flame-retardent without emitting
poisonous gases during fire. Delrin is chemical-resistant
and hardly influenced by known temperatures or atmospheric conditions.
P
A
G
E
THIS TUBING PROFILE BELOW MAKES
ALL TYPES OF CABLE TRAYS SUITABLE
FOR INSTRUMENT TUBING BY ETIN
CLAMP
This tubing profile is fixed to any cable tray with two
screws to obtain the efficiency of maximum use of space.
The tubing profile’s length is 190mm with a capacity of 16
pipes using 4 twin Etin clamps.
It pays to use the ETIN from the very
first clip!
Compare the ETIN clamp with all
BACK TO
competing clamps on the market.
ETIN has been developed for better
project economics.
The largest jobs give you the greatest advantages.
Front-mounting is only one of them. CATALOGUE
Compare ETIN with
competing clamps,
it pays!
MANY PARTS
COMPLICATE MATTERS
One of the common denominators of ETIN’s competitors
is many parts and/or little flexibility.
Bolts with loose washers and nuts that require nimble
hands for support on the back during mounting operations are still common. Brackets, clamp jaws, top plates
and lock plates are other loose parts that must be fitted
on site and take a lot of time and increase the cost of
the work at all staqes!
Single, standard ETIN clamps for
12mm tubes with top plate (cover) and
bolt.
One bolt (40mm) per 2 tubes left.
One bolt (65mm) per 4 tubes right.
FEW PARTS ARE MORE EFFICIENT
The greatest benefit from using the Øglaend ETIN
clamp is easier and quicker mounting. Few parts
also simplify ordering, storage, delivery and handling and make it easier to supplement, provide
better project control and greater flexibility. Loss
during mounting is reduced to a minimum. The
ETIN clamp combines all these advantages with
reasonable price. Mounted on the SPBE tray you
also obtain minimum use of space.
Adapters for 3/8”, 5/16” and 1/4” diameters.
Lugs lock adapter into clamps.
P
A
4 tubes =4 parts
Here you see four 12mm tubes mounted in a twin
ETIN clamp with top plate and bolt, clipped together to a self-supporting unit.
Insert the bolt through the hole. This locks the
clamp to the cable tray through tightening one of
the nuts.
G
E
ETIN TUBE CLAMP ORDERING LIST:
THE ETIN CLAMP IS SAFE DURING FIRE
Imperial tube (colour grey)
In the event of unnatural heating or fire the plastic core will
melt and the tubing assembly will lie freely in the clamp’s
steel jacket. The steel jacket encloses the tubes so that
they do not fall out, blocking escape routes. An important
safety detail. Because of the ETIN clamp’s simple design,
repair work following damage caused by heat/fire is
reduced to very fast disassembly and reclamping. - Select
a clamp type that does not loosen and fall out if the plastic jaw should melt.
FOR MAX. TUBE DIM. 1/2”
Type inch
ETIN TUBE CLAMP
OE-CBI
ADAPTER 1/2”-3/8”
OE-CA 1
ADAPTER 1/2”-5/16”
OE-CA 2*
ADAPTER 1/2”-1/4”
OE-CA 3
ETIN TOP PLATE
OE-CT
ETIN BOLTS in SS COMPL. WITH NUTS:
M6x40
OE-B1
M6x65
OE-B2
ETIN TUBING PROFILE
Order No.
77500
77501
77502*
77503
77422
77426
77427
EAP
ØgIaend System ETIN has only advantages!
BACK TO
CATALOGUE
Download PDF
Similar pages