contents 1. fundamental safety warnings ............. 7 2. safety warnings

CONTENTS
1. FUNDAMENTAL SAFETY WARNINGS .............7
2. SAFETY WARNINGS ....................................8
9.5 Making coffee using coffee beans ...............14
9.6 Making coffee using pre-ground coffee.......14
10. MAKING CAPPUCCINOS AND MILK-BASED
COFFEES .................................................. 15
2.1 Symbols used in these instructions ...............8
2.2 Designated use..............................................8
2.3 Instruction for Use .........................................8
10.1 Filling and attaching the milk container......15
10.2 Adjusting the amount of froth.....................15
10.3 Making cappuccinos and milk-based coffees
automatically ..............................................15
10.4 Cleaning the milk container after every use 16
3. INTRODUCTION..........................................8
3.1 Letters in brackets .........................................8
3.2 Troubleshooting and repairs..........................8
3.3 Download the App! .......................................8
11. MAKING HOT CHOCOLATE ..........................16
12. DELIVERING HOT WATER .......................... 17
13. STEAM DELIVERY ..................................... 17
4. DESCRIPTION.............................................9
4.1
4.2
4.3
4.4
Description of the appliance..........................9
Description of the homepage (main screen) 9
Description of the milk container ..................9
Description of the chocolate carafe ...............9
13.1 Tips for using steam to froth milk ................17
13.2 Clean the hot water/steam spout after use .17
14. CUSTOMISING THE DRINKS ...................... 18
15. MEMORISING YOUR PERSONAL PROFILE .... 18
16. CLEANING................................................ 18
5. BEFORE USE...............................................9
5.1
5.2
5.3
5.4
Checking the appliance .................................9
Installing the appliance.................................9
Connecting the appliance............................10
Setting up the appliance .............................10
16.1 Cleaning the machine.................................18
16.2 Cleaning the machine’s internal circuit ........18
16.3 Cleaning the coffee grounds container ........18
16.4 Cleaning the drip tray..................................19
16.5 Cleaning the inside of the coffee machine ...19
16.6 Cleaning the water tank ..............................19
16.7 Cleaning the coffee spouts ..........................19
16.8 Cleaning the pre-ground coffee funnel .......19
16.9 Cleaning the infuser ....................................20
16.10 Cleaning the milk container ........................20
16.11 Cleaning the hot water/steam connection
nozzle..........................................................21
16.12 Cleaning the hot chocolate carafe (E) ..........21
6. TURNING THE APPLIANCE ON.................... 10
7. TURNING THE APPLIANCE OFF .................. 10
8. MENU SETTINGS ...................................... 11
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
Rinsing ......................................................11
Descaling ...................................................11
Water filter ...............................................11
Drinks settings ...........................................11
Setting the time ........................................11
Auto-start ..................................................11
Auto-off (standby) ..................................... 12
Cup warmer ................................................ 12
Energy saving ............................................12
Coffee temperature ....................................12
Water hardness ..........................................12
Selecting the language ..............................12
Beep ..........................................................12
Cup lighting ..............................................12
Background ............................................... 13
Bluetooth ...................................................13
Demo mode ................................................13
Default values ...........................................13
Statistics ....................................................13
17. DESCALING .............................................. 21
18. SETTING WATER HARDNESS ...................... 22
18.1 Measuring water hardness ..........................22
18.2 Setting water hardness ..............................22
19. WATER SOFTENER FILTER ......................... 23
19.1 Installing the filter ......................................23
19.2 Replacing the filter......................................23
22. DISPLAYED MESSAGES.............................. 24
19.3 Removing the filter .....................................24
20.
21.
23.
24.
9. MAKING COFFEE....................................... 13
9.1
9.2
9.3
9.4
Selecting the coffee aroma..........................13
Selecting the coffee quantity ......................13
Adjusting the coffee mill .............................14
Tips for a hotter coffee.................................14
6
TECHNICAL DATA ...................................... 24
DISPOSAL ................................................ 24
TROUBLESHOOTING ................................. 29
ELECTRICAL REQUIREMENTS (UK ONLY) ..... 31
1. FUNDAMENTAL SAFETY WARNINGS
•
The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
•
Children should be supervised to ensure that they do not play with the appliance.
•
Cleaning and user maintenance shall not be made by children without supervision.
•
Never clean by immersing the appliance in water.
•
This is a household appliance only. It is not intended to be used in: staff kitchen areas in
shops, offices and other working environments; farm houses; by clients in hotels, motels and other residential type environments; bed and breakfast type environments.
•
If the plug or cord is damaged, it must be replaced by Customer Services only to avoid
all risk.
FOR EUROPEAN MARKETS ONLY:
•
This appliance can be used by children aged from 8 years and above if they have been
given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. User cleaning and maintenance shall not be made
by children unless they are above 8 years old and supervised. Keep the appliance and
power cord away from children under 8 years of age.
•
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are supervised or have been given
instruction concerning use of the appliance in a safe way and if they understand the
hazards involved.
•
Children shall not play with the appliance.
•
Always unplug the appliance when left unattended and before assembly, taking apart
or cleaning.
Surfaces marked with this symbol become hot during use (the symbol is present in
certain models only).
7
Any other use is considered improper and thus dangerous. The
manufacturer is not liable for damage deriving from improper
use of the appliance.
2. SAFETY WARNINGS
2.1 Symbols used in these instructions
Important warnings are identified by these symbols. It is vital to
respect these warnings.
2.3
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Please note:
Keep this Instruction for Use. If the appliance is passed to other
persons, they must also be provided with this Instruction for
Use.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Please note:
This symbol identifies important advice or information for the
user.
3. INTRODUCTION
Thank you for choosing this bean to cup espresso and cappuccino machine.
Take a few minutes to read this Instruction for Use. This will
avoid all risks and damage to the appliance.
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore follow these safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
• Unplug directly from the plug only. Never pull the cord as
you could damage it.
• To disconnect the appliance completely you must unplug it
from the mains socket.
• If the appliance is faulty, do not attempt to repair.
Turn it off, unplug from the mains socket and contact Customer Services.
• Before cleaning the appliance, turn it off, unplug from the
mains socket and allow to cool.
3.1
Letters in brackets
The letters in brackets refer to the legend in the description of
the appliance on pages 2-3.
3.2
Troubleshooting and repairs
In the event of problems, first try and resolve them by reading
the information given in sections “23. Displayed messages” and
“24. Troubleshooting”.
If this does not resolve the problem or you require further information, you should consult Customer Services by calling the
number given on the annexed “Customer Service” sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee. If repairs are required, contact
De’Longhi Customer Services only. The addresses are given in
the guarantee certificate provided with the machine.
Important:
Keep all packaging (plastic bags, polystyrene foam) away from
children.
3.3
Danger Scottature!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
When the appliance is in operation, the cup shelf could become
very hot.
2.2
Instruction for Use
Read this Instruction for Use carefully before using the appliance. Failure to follow this Instruction for Use may result in
burns or damage to the appliance.
The manufacturer is not liable for damage deriving from failure
to respect this Instruction for Use.
Download the App!
Designated use
This appliance is designed and made to prepare coffee, milk and
chocolate and to heat drinks.
A number of functions can be controlled remotely using the
De’Longhi Coffee Link App.
8
In the App, you can also find information, tips and curious facts
about the world of coffee, together with information on your
machine at your fingertips.
B9. Drinks available for selection (press the < or > scroll arrows to display all the drinks, the bottom bar indicates
which screen you are viewing)
B10. <: scroll arrow
B11. Customisable profiles (see “15. Memorising your personal
profile”)
This symbol highlights the functions you can control or
consult using the App.
You can also create up to 6 new drinks and save them in your
appliance.
Description of the accessories
(page 2 - C )
C1. “Total Hardness Test” indicator paper
C2. Pre-ground coffee measure
C3. Descaler
C4. Water softener filter (certain models only)
C5. Cleaning brush
C6. Hot water/steam spout
C7. Spout release button
C8. Power cord
Please note:
Check compatible devices on “PrimaDonnaElite. delonghi.com”.
4. DESCRIPTION
4.1 Description of the appliance
(page 3 - A )
A1. Beans container lid
A2. Pre-ground coffee funnel lid
A3. Beans container
A4. Pre-ground coffee funnel
A5. Grinding adjustment dial
A6. Cup warmer shelf
button: to turn the appliance on and off (standby)
A7.
A8. Coffee spouts (adjustable height)
A9. Hot water/steam connection nozzle
A10. Coffee grounds container
A11. Cup tray
A12. Drip tray water level indicator
A13. Drip tray grille
A14. Drip tray
A15. Water tank lid
A16. Water tank
A17. Water softener filter housing
A18. Infuser door
A19. Infuser
A20. Power cord connector socket
A21. Main switch (ON/OFF)
4.2
Description of the homepage (main screen)
B1.
(page 2 - B )
: menu to customise the drinks settings
4.3
Description of the milk container
(page 2 - D )
D1. Froth adjustment and CLEAN dial
D2. Milk container lid
D3. Milk container
D4. Milk intake tube
D5. Frothed milk spout (adjustable)
4.4
Description of the chocolate carafe
(page 2 - E )
E1. Chocolate carafe lid
E2. Funnel
E3. Steam spout
E4. Stirrer
E5. Hot chocolate carafe
E6. Funnel release slide
5. BEFORE USE
5.1 Checking the appliance
After removing the packaging, make sure the product is complete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact De’Longhi
Customer Services.
B2.
: appliance settings menu
B3. Selected aroma
B4. Clock
B5. Selected quantity
: aroma selection
B6.
: quantity selection
B7.
B8. >: scroll arrow
5.2
Installing the appliance
Important!
When you install the appliance, you should respect the following safety warnings:
• The appliance gives off heat. After positioning the appliance on the worktop, leave a space of at least 3 cm be-
9
•
•
•
tween the surfaces of the appliance and the side and rear
walls and at least 15 cm above the coffee maker.
Water penetrating the coffee maker could cause damage.
Do not place the appliance near taps or sinks.
The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
Arrange the cord in such a way that it cannot be damaged
by sharp edges or contact with hot surfaces (e.g. electric
hot plates).
5.
“WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS” appears on the display;
6. Press “ OK” to confirm. The appliance delivers water
from the spout (fig. 8) then goes off automatically.
The coffee machine is now ready for normal use.
•
•
5.3
Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to a correctly installed and efficiently
earthed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
electrician.
5.4
•
•
•
Please note!
When setting up the appliance, you need to make 4-5 cups
of coffee or 4-5 cappuccinos before the appliance starts to
give satisfactory results.
When making the first 5-6 cappuccinos, it is normal to hear
the noise of boiling water. After this, the noise becomes
less.
To improve the performance of your appliance, we recommend installing a water softener filter (C4) as described
in section “19. Water softener filter”. If your model is not
provided with a filter, you can request one from De’Longhi
Customer Services.
6. TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch
(A21) is pressed (fig. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appliance is ready for use only after completion of this cycle.
Setting up the appliance
Please note!
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee in the mill. The machine is, however, guaranteed to be
new.
You should customise water hardness as soon as possible
following the instructions in section “18. Setting water
hardness”.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
(A8) and is collected in the drip tray (A14) underneath. Avoid
contact with splashes of water.
button (A7-fig.
• To turn the appliance on, press the
9). The message “HEATING UP UNDERWAY PLEASE WAIT”
appears on the display.
When heating is complete, the message changes to “RINSING
UNDERWAY, HOT WATER FROM SPOUTS”. As well as heating the
boiler, this also heats the internal circuits by circulating hot
water.
The appliance is at temperature when the main screen (homepage) appears.
1. Plug the power cord (C8) connector into the socket (A20) at
the back of the appliance and connect the appliance to the
mains electricity supply (fig. 1). Make sure the main switch
(A21) at the back of the appliance is pressed (fig. 2);
2. “SELECT LANGUAGE”: press the flag corresponding to the
required language;
then follow the instructions which appear on the appliance
display:
3. “FILL TANK WITH FRESH WATER”: remove the water tank
(A16) (fig. 3), open the lid (A15) (fig. 4), fill to the MAX line
with fresh water (fig. 5), close the lid and put the tank back
in the appliance (fig. 6);
4. “INSERT WATER SPOUT”: Check that the hot water/steam
spout (C6) is inserted on the connection nozzle (A9) (fig. 7)
and place a container holding a minimum of 100 ml underneath (fig. 8);
7. TURNING THE APPLIANCE OFF
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts
(A8). Avoid contact with splashes of water.
• To turn the appliance off, press the
button (A7) (fig.
9).
10
”
•
The message “TURNING OFF UNDERWAY PLEASE WAIT”
appears on the display, then (if envisaged) the appliance
performs a rinse cycle and goes off (standby).
8.3
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• first turn the appliance off by pressing the
button
(fig. 9);
• release the main switch (A21) at the back of the appliance
(fig. 2).
8.4
8.1
indicated by the
, symbol, while the current value is
highlighted by the solid part of the vertical bar.
5. To go back to the settings menu, press “ ESC”.
To scroll and display the drinks, press
NEXT;
6. To reset the default values for the drink displayed, press “
RESET”;
7. “CONFIRM RESET?”: to confirm, press “ OK” (to cancel,
press “ ESC”);
8. “RESET DEFAULT VALUES DONE”: press “ OK” .
The drink has been reset to the default values. Continue with the
other drinks, or go back to the settings menu.
MENU SETTINGS
Rinsing
Use this function to deliver hot water from the coffee spouts
(A8) and hot water/steam spout (C6), if inserted, to clean and
heat the appliance’s internal circuit.
Place a container with a minimum capacity of 100ml under the
coffee and hot water spouts (fig. 8).
To enable the function, proceed as follows:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “ RINSING” appears on the
display (B);
3. Press “ ” to start rinsing.
8.5
•
8.2
Setting the time
To set the time on the display (B), proceed as follows:
” (B2) to enter the menu;
1. Press “
2. Press < (B10) or > (B8) until “ SET TIME” appears on the
display (B);
3. Press “ ”. The time setting panel appears on the display;
4. Press < o > corresponding to the hours and minutes until
the current time is displayed;
5. To confirm, press “ OK” (to cancel, press “ ESC”),
then press “ ESC” to go back to the homepage.
The time is now set.
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
4. After a few seconds, hot water is delivered first from the coffee spouts, then from the hot water/steam spout (if inserted) to clean and heat the appliance’s internal circuit. “RINSING UNDERWAY, HOT WATER FROM SPOUTS” appears on the
display, together with a progress bar which fills gradually as
preparation proceeds;
5. To stop rinsing, press “ STOP” or wait for rinsing to stop
automatically.
•
Drinks settings
In this section, you can consult your customised settings and, if
you wish, reset the default values for each drink.
” (B2) to enter the menu;
1. Press “
DRINKS SETTINGS” ap2. Press < (B10) or > (B8) until “
pears on the display (B);
3. Press “ ”. The values for the first drink appear on the
display;
4. The reference user profile is highlighted on the display. The
values are displayed on vertical bars. The default value is
Important!
Never press the main switch while the appliance is on.
8.
Water filter
For instructions on how to install the filter (C4), see section “19.
Water softener filter”.
8.6
Please note!
If the appliance is not used for more than 3-4 days, when
you turn it on again, we strongly recommend performing
2/3 rinses before use;
After cleaning, it is normal for the grounds container (A10)
to contain water.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function, the time must already be set correctly
(see section “8.5 Setting the time
”).
Descaling
To enable auto-start, proceed as follows:
1. Press “
” (B2) to enter the menu;
For instructions on descaling, see section “17. Descaling”.
11
8.10 Coffee temperature
2. Press < (B10) or > (B8) until “ AUTO-START” appears on
the display (B);
3. Select the function by pressing ”
”. The time setting
panel appears on the screen;
4. Press < o > corresponding to the hours and minutes until
the auto-start time is displayed;
5. Press
or
to enable or disable
auto-start.;
6. To confirm, press “ OK” (or cancel and go back to the
settings menu by pressing “ ESC”), then press “ ESC”
to go back to the homepage.
The auto-start time is now set and the corresponding symbol is
displayed to indicate that the function has been enabled.
8.7
To modify the temperature of the water used to make the coffee,
proceed as follows:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “ COFFEE TEMPERATURE” appears on the display (B) together with the current selection
(LOW, MEDIUM, HIGH or MAX);
3. Press “ ” to select the required temperature;
4. Press “ ESC” to go back to the homepage.
Please note!
A different temperature can be set for each profile (see section
“15. Memorising your personal profile”).
8.11 Water hardness
Auto-off (standby)
For instructions on setting water hardness, see section “18. Setting water hardness”.
Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-off, proceed as follows:
1. Press “
” (B2) to enter the menu;
AUTO-OFF” appears on
2. Press < (B10) or > (B8) until “
the display (B), together with the current selection (15 or 30
minutes, or 1, 2 or 3 hours);
3. Press “ ” to select the required value;
4. Press “ ESC” to go back to the homepage.
Auto-off is now programmed.
8.8
8.12 Selecting the language
To modify the language of the display (B), proceed as follows:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) o > (B8) finché appare sul display “
SELECT LANGUAGE” appears on the display;
3. Press “ ” : press < (B10) or > to display and select the flag
corresponding to the required language;
4. Press “ ESC” twice to go back to the homepage.
Cup warmer
8.13 Beep
To warm the cups before making coffee, you can enable the cup
warmer (A6) and rest the cups on the shelf.
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “ CUP WARMER” appears
on the display (B);
or disable3. Press “ ” per attivarethe cup warmer.
4. Press “ ESC” to go back to the homepage.
8.9
This enables or disables the beep emitted by the machine each
time an icon is pressed or an accessory is inserted/removed. To
disable or enable the beep, proceed as follows:
1. Press “
” (B2) to enter the menu;
BEEP” appears on the
2. Press < (B10) or > (B8) until “
display (B);
“ to enableor disable3. Press “
the beep;
4. Press “ ESC” to go back to the homepage.
Energy saving
Use this function to enable or disable energy saving. When enabled, the function reduces energy consumption in compliance
with European regulations.
To disable or enable “Energy Saving”, proceed as follows:
1. Press “
” (B2) to enter the menu;
8.14 Cup lighting
This function enables or disables the cup lights. The lighting is
enabled by default.
The lights comes on each time a coffee or milk-based drink is
made and during each rinsing cycle.
To disable or enable this function, proceed as follows:
” (B2) to enter the menu;
1. Press “
2. Press < (B10) o > (B8) until “ ENERGY SAVING” appears
on the display (B);
or disable 3. Press “ “ to enableenergy saving.
4. Press “ ESC” to go back to the homepage.
The corresponding symbol appears on the display alongside the
time to indicate that the function has been enabled.
2. Press < (B10) or > (B8) until “ CUP LIGHTING” appears on
the display (B);
3.
12
Press “ “ to enablecup lighting;
or disable -
the
4. Press “
ESC” to go back to the homepage.
3.
Press “ “ and then “ OK” to restore the original parameters (or “ ESC” to leave the parameters unaltered);
4. Press “ OK” to go back to the settings menu and “
ESC” to go back to the homepage.
8.15 Background
You can choose the display background from the following 4 alternatives: “SHADED BLUE”, “STAINLESS STEEL”, “COFFEE BROWN”,
“DARK BLUE”. Proceed as follows:
1. Press “
” (B2) to enter the menu;
BACKGROUND” appears
2. Press < (B10) or > (B8) until “
on the display (B);
3. Press “ ”: The backgrounds available appear on the
display;
4. Select the required background by pressing the chosen
panel. The appliance goes back to the settings menu with
the new background;
5. Press “ ESC” to go back to the homepage.
8.19 Statistics
This displays statistics relating to the machine. To display the
statistics, proceed as follows:
1. Press “
” (B2) to enter the menu;
STATISTICS” appears
2. Press < (B10) or > (B8) until “
on the display (B);
3. Press “ ” to verify all the available statistics by pressing
< or >;
4. Press “ ESC” to go back to the homepage.
8.16 Bluetooth
9.
9.1
This function enables or disables the protection PIN to connect
to the appliance from a device.
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “ BLUETOOTH” appears on the
display (B);
3. Enable or disable the PIN protection by pressing
;
or
4. Press “ ESC” to go back to the homepage.
The preset PIN is “0000”. You are recommended to customise the
PIN directly from the APP.
MAKING COFFEE
Selecting the coffee aroma
Select the required aroma by pressing “
AROMA” (B6):
(see “9.6 Making coffee
using pre-ground coffee”)
EXTRA LIGHT AROMA
LIGHT AROMA
MEDIUM AROMA
Please note!
The serial number of the appliance enables it to be identified
unambiguously when an association is created with the APP.
STRONG AROMA
EXTRA STRONG AROMA
8.17 Demo mode
When this mode is enabled, the appliance’s main functions are
illustrated on the display:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “
DEMO MODE” appears
on the display (B);
3. Press “ “ to start the demo;
4. Press “ ESC” to go back to the homepage.
Custom (if programmed) /
Standard
9.2
Selecting the coffee quantity
Select the required quantity of coffee in the cup by pressing “
QUANTITY” (B7):
SMALL SIZE
8.18 Default values
MEDIUM SIZE
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language which
remains as set).
To reset the default values, proceed as follows:
1. Press “
” (B2) to enter the menu;
DEFAULT VALUES”
2. Press < (B10) or > (B8) until “
appears on the display (B);
LARGE SIZE
EXTRA LARGE SIZE
Custom quantity (if programmed)/Standard quantity
13
9.3
6. Preparation begins. An image of the selected drink appears
on the display (B) together with a progress bar which gradually fills as preparation progresses.
Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that the
coffee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment dial (A5 - fig. 10).
•
“ during preparation of 1
time by pressing “2X
ESPRESSO (the image is displayed for a few seconds at the
start of preparation).
• While the machine is making coffee, delivery can be interrupted at any moment by pressing “ STOP”.
• As soon as delivery has ended, to increase the quantity of
coffee in the cup, just press “ EXTRA”. When the required
quantity is reached, press “ STOP”.
Once the coffee has been made, the appliance is ready to make
the next drink.
Please note!
The grinding adjustment dial must only be turned when the
coffee mill is in operation.
If the coffee is delivered too slowly or
not at all, turn one click clockwise towards “7”.
For fuller bodied creamier coffee, turn
one click anticlockwise towards “1” (do
not turn more than one click at a time
otherwise the coffee could be delivered a drop at a time).
These adjustments will only be evident after at least 2 cups of
coffee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
9.4
•
Tips for a hotter coffee
•
•
For hotter coffee, you should:
• perform a rinse cycle by selecting the “Rinse” function in
the settings menu (see section “8.1 Rinsing
”);
• warm the cups with hot water (using the hot water function, see section “12. Delivering hot water”);
• increase the coffee temperature in the settings menu (see
section “8.10 Coffee temperature ”).
•
9.6
9.5
Please note:
You can prepare 2 cups of ESPRESSO coffee at the same
Making coffee using coffee beans
•
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
•
1. Fill the container (A3) (fig. 11) with coffee beans;
2. Place a cup under the coffee spouts (A8);
3. Lower the spouts as near as possible to the cup (fig. 12).
This makes a creamier coffee;
4. Press <(B10) or > (B8) until the required coffee is
displayed;
5. Then select your required coffee:
• ESPRESSO
• DOPPIO+
• COFFEE
• LONG
• 2 ESPRESSO
Please note!
Various alarm messages could be displayed while using
the appliance (FILL TANK, EMPTY GROUNDS CONTAINER,
etc.). Their meaning is explained in section “23. Displayed
messages”.
For hotter coffee, see section “9.4 Tips for a hotter coffee”.
If the coffee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in section “9.3 Adjusting the coffee mill” and section “24. Troubleshooting”.
Preparation of each coffee can be customised (see sections
“14. Customising the drinks” and “15. Memorising your
personal profile”).
Making coffee using pre-ground coffee
Important!
Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
it. This could damage the appliance.
Never use more than 1 level measure (C2) or it could dirty
the inside of the coffee machine or block the funnel (A4).
Please note!
If you use pre-ground coffee, you can only make one cup of coffee at a time.
1. Press “
AROMA” (B6) repeatedly until “ ” (preground) appears on the display (B);
2. Open the pre-ground coffee funnel lid (A2);
3. Make sure the funnel (A4) is not blocked, then add one
level measure of pre-ground coffee (fig. 13);
4. Place a cup under the coffee spouts (A8) (fig. 12);
5. Press the image corresponding to the required coffee (ESPRESSO, COFFEE, LONG);
14
6. Preparation begins. An image of the selected drink appears
on the display, together with a progress bar which gradually fills as preparation progresses.
10.2
Important! Making LONG coffee
:
Halfway through preparation, the message “ADD PRE-GROUND
COFFEE, MAXIMUM ONE MEASURE” is displayed. Add one level
measure of pre-ground coffee and press “ OK” .
Dial
position
Please note!
If “Energy Saving” mode is active, you may have to wait a few
seconds before the first coffee is delivered.
f
10. MAKING CAPPUCCINOS AND MILK-BASED
COFFEES
•
Please note!
To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid (D2) and hot water connection nozzle (A9) as described in sections “10.4 Cleaning
the milk container after every use”, “16.10 Cleaning the
milk container” and “16.11 Cleaning the hot water/steam
connection nozzle”.
10.3
1. Remove the lid (D2) (fig. 14);
2. Fill the milk container (D3) with a sufficient quantity of
milk, not exceeding the MAX level marked on the handle
(fig. 15). Each mark on the side of the container corresponds to about 100 ml of milk;
•
Description
Recommended for…
NO FROTH
HOT MILK (not frothed)
CAFFELATTE
MIN. FROTH
LATTE MACCHIATO / FLAT
WHITE
MAX. FROTH
CAPPUCCINO/ CAPPUCCINO+ / CAPPUCCINO MIX/
ESPRESSO MACCHIATO /HOT
MILK (frothed)
Making cappuccinos and milkbased coffees automatically
1. Fill the milk container (D) and attach it as described above.
2. Select the required drink:
• CAPPUCCINO
• LATTE MACCHIATO
• CAFFELATTE
• LATTE CALDO
• CAPPUCCINO+
• ESPRESSO MACCHIATO
• FLAT WHITE
• CAPPUCCINO MIX
3. A message on the display (B) instructs you to turn the froth
adjustment dial (D1) according to the froth required by the
original recipe. Turn the dial on the milk container lid (D2)
and confirm the selection by pressing “ OK”.
4. After a few seconds, preparation begins automatically and
an image of the selected drink appears on the display, together with a progress bar which gradually fills as preparation progresses.
10.1 Filling and attaching the milk container
•
Adjusting the amount of froth
Turn the froth adjustment dial (D1) to adjust the amount of froth
on the milk delivered while making cappuccinos and milk-based
coffees.
Please note!
For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
If “Energy Saving” mode is enabled, you may have to wait a
few seconds before the drink is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (fig. 16);
4. Place the lid back on the milk container;
5. If present, extract the hot water/steam spout (C6) by pressing the release button (C7) (fig. 17);
6. Attach the milk container (D) to the connection nozzle (A9)
(fig. 18) and push as far as it will go. The machine emits a
beep (if the beep function is enabled);
7. Place a sufficiently large cup under the coffee spouts (A8)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(fig. 19).
8. Follow the instructions below for each function.
•
•
•
15
Please note: general indications when preparing all
milk-based drinks
“ ESC”: press to interrupt preparation completely and
go back to the homepage.
“ STOP”: press to interrupt milk or coffee delivery and
move on to the next delivery to complete the drink.
At the end of delivery, to increase the quantity of coffee in
the cup, press “ EXTRA”.
Choose CHOCOLATE from the homepage, then proceed as
follows:
1. Lift the carafe lid (E1) (fig. 23);
2. Pull the release slide (E6) and extract the carafe funnel (E2)
(fig. 23);
3. Make sure the steam spout (E3) and stirrer (E4) are inserted (fig. 24);
4. “INSERT STIRRER IN CHOCOLATE CARAFE (STEP 1 OF 4)”
(fig. 25): attach the funnel to the carafe, then press “
NEXT”;
5. “POUR MILK OR WATER (STEP 2 OF 4)” (fig. 26): to make
one cup of chocolate, pour milk at refrigerator temperature
(or cold water) into the funnel up to the
level. To
make two cups or one mug of hot chocolate, pour the milk
level.
(or water) into the funnel up to the
When you have added the milk, press “ NEXT”;
6. “ADD CHOCOLATE POWDER THROUGH THE FUNNEL (STEP
3 OF 4)” (fig. 27): to make one cup of chocolate, add two
measures (C2) (25 g) of hot chocolate powder. To make two
cups or one mug of hot chocolate, added 4 measures of hot
chocolate powder. When you have added the hot chocolate
powder, press “ NEXT”;
•
Preparation of each cappuccino or milk-based coffee can
be customised (see sections “14. Customising the drinks”
and “15. Memorising your personal profile”).
• Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poorer
the quality of froth produced.
Once the coffee has been made, the appliance is ready to make
the next drink.
10.4 Cleaning the milk container after every use
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water and steam leak out of the frothed milk spout (D5).
Avoid contact with splashes of water.
Each time you use a milk function, “TURN DIAL TO <CLEAN>
POSITION TO START CLEANING” appears on the display:
1. Leave the milk container (D) in the machine (you do not
need to empty it);
2. Place a cup or other recipient under the frothed milk spout
(fig. 20);
3. Turn the froth adjustment dial (D1) to “CLEAN”. “CLEANING
MILK CONTAINER UNDERWAY PLACE A RECIPIENT UNDER
MILK SPOUT” appears on the display (B) (fig. 21) together with a bar which gradually fills as cleaning progresses.
Cleaning stops automatically;
4. Turn the dial back to one of the froth selections;
5. Remove the milk container and always clean the steam
connection nozzle (A9) with a sponge (fig. 22).
•
•
•
•
11.
•
•
Please note!
To prepare a number of cappuccinos or milk-based coffees,
clean the milk container after you have prepared the last
drink only. To proceed with making the next drinks, press “
ESC”.
symIf you do not clean the milk container, the
bol appears on the display to remind you that it needs
cleaning.
The milk container can be kept in the refrigerator.
In some cases, before cleaning you must wait for the appliance to heat up.
•
•
Important!
Make sure the hole in the funnel shown in fig. 28 is clean.
Please note!
The milk must be poured into the funnel when the steam
spout and stirrer are already in place. Do not exceed the
MAX level marked on the carafe. Increase or reduce the
quantity of hot chocolate powder according to taste.
To use water instead of milk, follow the instructions for
milk.
To prepare hot chocolate correctly, first pour the milk into
the funnel, then add the hot chocolate or cocoa powder as
shown on the hot chocolate carafe lid.
7. “CLOSE THE LID AND INSERT CHOCOLATE CARAFE (STEP 4
OF 4)”: Close the lid (fig. 29) and attach the carafe to the
connection nozzle, pushing as far as it will go (fig. 30). The
appliance emits a beep (if the beep function is enabled).
The hot chocolate settings screen is displayed;
8. “SELECT CUPS NUMBER AND DENSITY, PRESS OK TO START”:
press the selection arrows to choose 1 cup (
or 2 cups (
) and the required density (min=
; max =
). Press “
OK” to start the function. The appliance starts mixing the
hot chocolate powder then delivers steam to heat it.
MAKING HOT CHOCOLATE
Please note!
When in energy saving mode, a few seconds may elapse before
the first drink is delivered.
You can make one or two cups of hot chocolate.
16
”
•
•
1. Make sure the hot water/steam spout (C6) is attached correctly to the hot water/steam connection nozzle (A9);
2. Fill a container with the liquid to be heated or frothed and
immerse the hot water/steam spout in the liquid;
Please note!
If the hot chocolate powder used does not contain thickener, adjusting the density will have no effect.
To stop making chocolate, press “ STOP”.
STEAM”. The corresponding image appears
3. Press “
on the display (B), together with a progress bar which fills
gradually as preparation proceeds and after a few seconds,
steam to heat the liquid is delivered from the hot water/
steam spout;
4. When the required temperature or level of froth is obtained, interrupt steam delivery by pressing “ STOP”.
(You should not deliver steam for more than 3 minutes at a
time);
Once the chocolate has been made, the appliance prepares to
make the next drink. The chocolate is ready to be poured into
the cup.
•
•
•
•
Danger of burns!
While making the chocolate, the carafe and lid become
very hot. Hold by the handle only to remove the carafe and
pour the chocolate.
While making the hot chocolate, it is normal for steam to
come out of the holes in the chocolate carafe lid.
Heating the milk causes splashes inside the carafe. This is
normal.
The quantity of hot chocolate in the cup varies according to
the density selected. The quantity is less with a high density than with a low density.
Important!
Always stop steam delivery before extracting the container containing the liquid to avoid burns from splashes.
Please note!
If “Energy Saving” mode is active, you may have to wait a few
seconds before the hot water is delivered.
12. DELIVERING HOT WATER
13.1 Tips for using steam to froth milk
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached correctly to the hot water/steam connection nozzle (A9);
2. Place a container under the spout (as close as possible to
avoid splashes);
•
•
•
•
HOT WATER”. The corresponding image ap3. Press “
pears on the display (B), together with a progress bar
which fills gradually as preparation proceeds;
4. The machine delivers about 250 ml of hot water, then
delivery stops automatically. To interrupt delivery of hot
water manually, press “ STOP” .
•
•
When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
For a creamier froth, rotate the container with slow movements in an upward direction.
To avoid milk with poor froth or large bubbles, always clean
the spout (C6) as described in the following section.
13.2 Clean the hot water/steam spout after use
Always clean the hot water/steam spout (C6) after use to avoid
the build-up of milk residues and prevent it from clogging.
1. Place a container under the hot water/steam spout and deliver a little water (see section “12. Delivering hot water”).
Stop delivery of hot water by pressing “ STOP”.
2. Wait a few minutes for the hot water/steam spout to cool
down, then extract (fig. 17) by pressing the release button
(C7). Hold the spout with one hand and with the other,
turn the hot water/steam spout and pull it downwards
(fig. 31).
3. Also remove the steam connection nozzle by pulling it
downwards (fig. 32).
4. Check the hole in the connection nozzle is not blocked. If
necessary, clean using a toothpick.
5. Wash all parts of the spout thoroughly with a sponge and
warm water.
Please note!
If “Energy Saving” mode is active, you may have to wait a
few seconds before the hot water is delivered.
Preparation of hot water can be customised (see sections
“14. Customising the drinks” and “15. Memorising your
personal profile”).
13. STEAM DELIVERY
Important! Danger of burns.
Do not leave the appliance unattended while steam is being
delivered.
17
6. Insert the nozzle and hot water/steam spout on the connection nozzle by pushing it upwards and turning it clockwise until it is attached.
•
•
14.
CUSTOMISING THE DRINKS
The aroma (when required) and quantity of the drinks can be
customised.
1. Make sure the profile for which you want to customise the
drink is active;
16. CLEANING
16.1
(B1);
2. From the homepage, press
3. To access the customising screen, choose the drink you
want to customise;
4. “CHOOSE COFFEE AROMA”: Select the required aroma by
pressing
or
and press “ OK” ;
5. “CUSTOMISING COFFEE QUANTITY, STOP TO SAVE”: Preparation begins and the appliance displays the quantity
customising screen in the form of a vertical bar. The star
alongside the bar represents the current quantity;
6. When the quantity reaches the minimum quantity you can
set, “ STOP” is displayed.
7. When the required quantity is reached, press “ STOP”.
8. “SAVE NEW SETTINGS?”: Press “YES” or “NO”.
The appliance confirms if the values have been saved or not (depending on the previous selection). Press “ OK”.
The appliance goes back to the homepage.
•
•
•
“ GUEST” profile: when you select this profile, you can
deliver drinks with the default settings. The
function
is not active.
You can rename your personal profile by connecting with
the DeLonghi Coffee Link App.
Cleaning the machine
The following parts of the machine must be cleaned regularly:
- the appliance’s internal circuit;
- coffee grounds container (A10);
- drip tray (A14);
- water tank (A16);
- coffee spouts (A8);
- pre-ground coffee funnel (A4);
- infuser (A19), accessible after opening the infuser door
(A18);
- milk container (D);
- chocolate carafe (E);
- hot water/steam connection nozzle (A9);
- display (B).
•
Please note!
Cappuccino and milk-based coffees: the coffee aroma
is saved first, followed by the quantities of first milk, then
coffee;
Hot water: the appliance delivers hot water. Press “
STOP” to save the required quantity.
You can also customise the drinks by connecting with the
DeLonghi Coffee Link App.
•
•
Important!
Do not use solvents, abrasive detergents or alcohol to clean
the coffee machine. With De’Longhi superautomatic coffee
machines, you need not use chemical products to clean the
machine.
None of the components of the appliance can be washed in
a dishwasher with the exception of the milk container (D)
and chocolate carafe (E).
Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
16.2 Cleaning the machine’s internal circuit
15.
If the appliance is not used for more than 3/4 days, before using
it again, we strongly recommend switching it on and:
• performing 2-3 rinse cycles by selecting the “Rinse” function (section “8.1 Rinsing ”;
• delivering hot water for a few seconds (section “12. Delivering hot water”).
MEMORISING YOUR PERSONAL
PROFILE
The appliance allows you to memorise 6 different profiles, each
associated with a different icon.
The profile displays the drinks most frequently selected from
that profile and the aroma and quantity selections for each drink
are memorised.
To select your personal profile, from the homepage press “
PROFILE 1” (B11), then select another numbered profile.
To enter another profile, press the profile currently in use then
press another profile.
Please note!
After cleaning, it is normal for the grounds container (A10) to
contain water.
16.3 Cleaning the coffee grounds container
When “EMPTY GROUNDS CONTAINER” appears on the display
(B), the grounds container must be emptied and cleaned. The
Please note!
18
appliance cannot be used to make coffee until you have cleaned
the grounds container (A10). Even if not full, the empty grounds
container message is displayed 72 hours after the first coffee has
been prepared. For the 72 hours to be calculated correctly, the
machine must never be turned off with the main switch.
16.5 Cleaning the inside of the coffee machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned off
(see section “7. Turning off”) and unplugged from the mains
power supply. Never immerse the coffee machine in water.
1. Check regularly (about
once a month) that the
inside of the appliance
(accessible after removing the drip tray (A14) )
is not dirty. If necessary,
remove coffee deposits
with the brush (C5) supplied and a sponge.
2. Remove all the residues
with a vacuum cleaner
35
(fig. 35).
Important! Danger of burns
If you make a number of cappuccinos one after the other, the
metal cup tray (A11) becomes hot. Wait for it to cool down before touching it and handle it from the front only.
To clean (with the machine on):
•
Remove the drip tray
(A14) (fig. 33), empty
and clean.
•
Empty the grounds container (A10) and clean
thoroughly to remove
all residues left on the
bottom. This can be
done using the spatula on the brush (C5)
33
provided.
16.6 Cleaning the water tank
1. Clean the water tank (A16) regularly (about once a month)
and whenever you replace the water softener filter (C4) (if
provided) with a damp cloth and a little mild washing up
liquid;
2. Remove the filter (if present) and rinse with running water;
3. Replace the filter (if provided), fill the tank with fresh
water and replace the tank;
4. (Models with water softener filter only) Deliver about
100ml of hot water to reactivate the filter.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds. If this is not done,
when you make the next coffees, the grounds container may fill
up more than expected and clog the machine.
16.4 Cleaning the drip tray
16.7 Cleaning the coffee spouts
Important!
34
The drip tray (A14) is fitted
with a level indicator (A12)
(red) showing the level of
water it contains (fig. 34).
Before the indicator protrudes from the cup tray
(A11), the drip tray must be
emptied and cleaned, otherwise the water may overflow
the edge and damage the
appliance, the surface it rests
on or the surrounding area.
36A
1. Clean the coffee spouts
(A8) regularly with a
sponge or cloth (fig.
36A);
2. Check that the holes in
the coffee spouts are not
blocked. If necessary,
remove coffee deposits
with a toothpick (fig.
36B).
36B
To remove the drip tray:
1. Remove the drip tray and the coffee grounds container
(A10) (fig. 33);
2. Empty the drip tray and grounds container and wash them;
3. Replace the drip tray and grounds container.
16.8 Cleaning the pre-ground coffee funnel
Check regularly (about once a month) that the pre-ground
coffee funnel (A4) is not blocked. If necessary, remove coffee
deposits with the brush (C5) supplied.
19
16.9
Please note!
If the infuser is difficult to insert, before insertion, adapt it to the
right size by pressing the two levers shown in fig. 40.
8. Once inserted, make sure
the two coloured buttons have snapped out
(fig. 41);
9. Close the infuser door;
10. Put the water tank back.
Cleaning the infuser
The infuser (A19) must be cleaned at least once a month.
PU
SH
PU
SH
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned off (see section
“7. Turning off”);
2. Remove the water tank (A16) (fig. 3);
PU
SH
41
16.10
37
Cleaning the milk container
To keep the frother efficient, clean the milk container (D) every
two days as described below:
1. Remove the lid (D2);
2. Remove the milk spout (D5) and intake tube (D4) (fig. 42);
3. Turn the froth adjustment dial (D1) anticlockwise to the
“INSERT” position (fig. 42) and pull it off upwards;
38
3. Open the infuser door (A18) (fig. 37) on the right side of
the appliance;
4. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (fig. 38);
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap;
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID - NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
6. Use the brush (C5) to remove any coffee residues left in the
infuser housing, visible through the infuser door;
7. After cleaning, replace the infuser by sliding it onto the
internal support (fig. 39), then push the PUSH symbol fully
in until it clicks into place;
42
4. Wash all the components thoroughly with hot water and
mild washing-up liquid. All components are dishwasher
safe, placing them in the top basket of the dishwasher.
Make sure there are no milk residues on the hollow and
groove under the dial (fig. 43). If necessary, scrape the
groove with a toothpick;
39
40
20
•
43
You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer’s guarantee.
Descale the appliance when “DESCALING NEEDED PRESS OK TO
”: appears on the display (B). To descale
START (~40min)
the appliance immediately, press “ OK” and follow the instructions from point 4.
To descale the appliance later, press “ ESC”. The
symbol
appears on the display to remind you that the appliance needs
descaling.
To access the descaling menu:
1. Press “
” (B2) to enter the menu;
2. Press < (B10) or > (B8) until “ DESCALING” appears on
the display;
3. Press “ “ to start the descaling cycle then follow the instructions on the display;
4. “REMOVE WATER SOFTENER FILTER” (fig. 45):
extract the water tank
(A16), remove the water
softener filter (C4) (if
present) and empty the
water tank. Press “
NEXT”;
44
5. Rinse inside the froth adjustment dial seat with running
water (fig. 44);
6. Check that the intake tube and spout are not clogged with
milk residues;
7. Replace the dial (in correspondence to the word “INSERT”),
spout and milk intake tube;
8. Place the lid back on the milk container (D3).
16.11 Cleaning the hot water/steam connection
nozzle
Each time you prepare milk, clean the connection nozzle (A9)
with a sponge to remove milk residues from the gaskets (fig.
22).
16.12 Cleaning the hot chocolate carafe (E)
45
5
Clean the carafe each time you make hot chocolate as described
below:
1. Lift the lid (E1) and remove the funnel (E2) by pressing
the release button (E6) and lifting (fig. 23);
2. Extract the steam spout (D3) and stirrer (D4);
3. Wash all the components thoroughly with hot water and
mild washing-up liquid.
All components are dishwasher safe, placing them
in the top basket of the dishwasher.
4. Replace all the components in the appliance.
A
•
B
B
A
Please note!
It is normal to find residues on the stirrer while cleaning. These
consist of traces of iron in the cocoa attracted by the magnets
in the stirrer.
17.
+
5. “ADD DE’LONGHI DESCALER (LEVEL A) AND WATER
(UP TO LEVEL B)” (fig. 46);
Pour the descaler into the
tank up to the level A
marked inside the tank
(equal to one 100 ml
pack), then add water
(one litre) up to level B
and put the water tank
back. Press “ NEXT”;
46
6
6. “EMPTY DRIP TRAY” (fig.
47): Remove, empty
and replace the drip tray
(A14) and grounds container (A10). Press “
NEXT”;
DESCALING
Important!
Before use, read the instructions and the labelling on the
descaler pack.
47
21
7. “PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
DESCALING”: Place an empty container with a minimum
capacity of 2 litres under the hot water/steam spout (C6)
and coffee spouts (A8) (fig. 8);
17. Hot water is delivered from the hot water/steam spout and
“RINSING UNDERWAY” is displayed;
18. “EMPTY DRIP TRAY” (fig. 45): At the end of rinsing, remove,
empty and replace the drip tray (A14) and grounds container (A10). Press “ NEXT”;
18. “DESCALE COMPLETE”: press “ OK”;
19. “FILL TANK WITH FRESH WATER”: empty the container used
to collect the rinse water, remove the water tank and fill
with fresh water up to the MAX level, then put back in the
appliance.
Descaling is complete.
Important! Danger of burns
Hot water containing acid flows out of the hot water/steam
spout. Take care to avoid contact with splashes of this solution.
8. Press “ OK” to confirm that you have added the descaling solution. “DESCALING UNDERWAY” appears on the
display. The descale programme starts and the descaler
liquid comes out of the hot water/steam and coffee spouts.
A series of rinses and pauses is performed automatically to
remove all the scale residues inside the coffee machine;
After about 25 minutes, descaling stops;
9. “RINSE AND FILL WATER TANK UP TO MAX LEVEL” (fig. 5):
the appliance is now ready to rinse with fresh water. Empty
the container used to collect the descaler solution. Extract
the water tank, empty, rinse under running water, fill
with fresh water up to the MAX level and put back in the
appliance;
10. “PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
RINSING”: Place the container used to collect the descaler
solution empty under the coffee spouts and hot water/
steam spout (fig. 8) and press “ OK” ;
11. Hot water is delivered first from the coffee spouts, then
from the hot water/steam spout and “RINSING UNDERWAY”
is displayed;
12. When the water in the tank has run out, empty the container used to collect the rinsing water;
13. “INSERT FILTER INTO ITS
HOUSING” (fig. 48). Press
“
NEXT” and extract
the water tank. Replace
the water softener filter if
removed previously;
14. “RINSE AND FILL WATER
TANK UP TO MAX LEVEL”
(fig. 5): Fill the tank up to
the MAX level with fresh
water;
•
•
18.
Please note!
If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
After descaling, it is normal for the grounds container
(A10) to contain water.
SETTING WATER HARDNESS
The “DESCALE” message is displayed after a period of time established according to water hardness.
The machine is set by default for a hardness of “LEVEL 4”. The
machine can also be programmed according to the hardness
of the mains water in the various regions so that the machine
needs to be descaled less often.
18.1 Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper (C1)
from its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
soft water
slightly hard water
48
8
hard water
15. “INSERT WATER TANK” (fig. 6): Put the water tank back in the
appliance;
16. “PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
RINSING”: Place the container used to collect the descaler
solution empty under the hot water/steam spout (fig. 8)
and press “ OK” ;
very hard water
18.2 Setting water hardness
1. Press “
” (B2) to enter the menu;
2.
22
Press < (B10) or > (B8) until “
pears on the display (B);
WATER HARDNESS” ap-
3. To change the level selected, press the symbol itself until
the required level is displayed (Level 1 = soft water; Level 4
= very hard water);
4. Press “ ESC” to go back to the homepage.
The machine is now reprogrammed with the new water hardness setting.
19.
7. Extract the tank (A16) from the appliance and fill with
water.
8. “IMMERSE FILTER IN THE
WATER TANK LETTING AIR
BUBBLES ESCAPE” (fig.
51): Insert the filter in the
water tank and immerse
it completely for about
ten seconds, sloping it
and pressing it lightly to
enable the air bubbles
to escape. Press “
NEXT”;
WATER SOFTENER FILTER
Certain models are fitted with a water softener filter (C4). If this
is not the case with your model, you are recommended to purchase one from De’Longhi Customer Services.
To use the filter correctly, follow the instructions below.
5
51
19.1 Installing the filter
9. “INSERT FILTER INTO ITS HOUSING AND PUSH IT DOWN TO
THE BOTTOM”: Insert the filter in the filter housing (A17)
(fig. 48) and press as far as it will go. Press “ NEXT”;
10. “INSERT WATER TANK”: Close the tank with the lid (A15),
then replace the tank in the machine.
11. “PLACE 0.5l CONTAINER UNDER SPOUTS, PRESS OK TO FILL
FILTER” (fig. 8): Place the container under the hot water
spout (C6) and press “ OK”. Delivery begins and stops
automatically.
The filter is now active and you can use the coffee machine.
1. Remove the filter (C4) from the packaging;
2. Press “
” (B2) to enter the menu;
3. Press <(B10) or > (B8) until “ WATER FILTER” appears on
the display;
4. Press “ “;
5. “TURN THE DATE INDICATOR UNTIL THE NEXT 2
MONTHS ARE DISPLAYED”
(fig. 49): turn the date
disk to display the next
2 months of use. Press “
NEXT”;
19.2 Replacing the filter
Replace the filter (C4) when “REPLACE WATER SOFTENER FILTER, PRESS OK TO START
” appears on the display (B). To
replace the filter immediately, press “ OK” and follow the
instructions from point 4.
symbol
To replace the filter later, press “ ESC”. The
appears on the display to remind you that the filter needs
replacing.
To replace the filter, proceed as follows:
1. Extract the tank (A16) and exhausted filter;
2. Remove the new filter from the packaging;
3. Press “
” (B2) to enter the menu;
Please note
The filter lasts about two
months if the appliance is
49 used normally. If the coffee
machine is left unused with
the filter installed, it will last a maximum of three weeks.
6. “RUN WATER INTO FILTER
HOLE UNTIL IT COMES
OUT FROM OPENINGS”
(fig. 50): To activate
the filter, run tap water
through the hole in the
filter as shown in the
figure until water comes
out of the openings at the
side for more than a minute. Press “ NEXT”;
4. Press <(B10) or > (B8) until “ WATER FILTER” appears on
the display;
5. Press “ “;
6. “ REPLACE FILTER” appears on the display;
7. Press “ “;
8. Follow the operations described in the previous section
from point 5.
The filter is now active and you can use the coffee machine.
50
23
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the filter even if
the message has not yet been displayed.
19.3 Removing the filter
20. TECHNICAL DATA
Replace the filter (C4) when “REPLACE WATER SOFTENER FILTER,
PRESS OK TO START
” appears on the display (B). To replace the filter immediately, press “ OK” and follow the instructions from point 3.
symbol
To replace the filter later, press “ ESC”. The
appears on the display to remind you that the filter needs
replacing.
To use the appliance without the filter, proceed as follows:
1. Extract the tank (A16) and exhausted filter;
2. Press “
” (B2) to enter the menu;
3. Press <(B10) or > (B8) until “ WATER FILTER” appears on
the display;
4. Press “ “;
Voltage:
220-240 V~ 50/60 Hz max. 10 A
Power:
1450 W
Pressure:
1,5 MPa (15 bar)
Water tank capacity:
2l
Size LxDxH:
260x480x375 mm
Cord length:
1750 mm
Weight:
12,4 kg
Beans container capacity:
400 g
The appliance complies with the following EC
directives:
•
•
5. “ REMOVE FILTER” appears on the display;
6. Press “ ”;
CONFIRM REMOVE FILTER”: press “
OK” (or
7. “
press “ ESC” to go back to the settings menu);
European Standby Regulation 1275/2008
Materials and accessories coming into contact with food
conform to EEC regulation 1935/2004.
21. DISPOSAL
The appliance must not be disposed of with household waste, but taken to an authorised waste separation and recycling centre.
8. “
REMOVE FILTER COMPLETED”: the change has
been saved. Press “ OK” to go back to the homepage.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the filter even if
the message has not yet been displayed.
22.
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
SOLUTION
FILL TANK WITH FRESH
WATER
Insufficient water in the tank (A16).
Fill the tank with water and/or insert it correctly, pushing it as far as it will go until it
clicks into place.
INSERT WATER TANK
The tank (A16) is not correctly in place.
Insert the tank correctly and press as far as it
will go.
24
EMPTY GROUNDS CONTAINER The grounds container (A10) is full.
Empty the grounds container and drip tray
(A14), clean and replace. Important: when
removing the drip tray, the grounds container
MUST be emptied, even if it contains few grounds. If this is not done, when you make the next
coffees, the grounds container may fill up more
than expected and clog the machine.
INSERT GROUNDS CONTAINER After cleaning, the grounds container has not Remove the drip tray (A14) and insert the
been replaced (A10).
grounds container.
ADD PRE-GROUND COFFEE
MAXIMUM ONE MEASURE
With the “pre-ground coffee” function selected, Place pre-ground coffee in the funnel (fig. 13)
pre-ground coffee has not been poured into the and repeat delivery
funnel (A4).
ESC
ADD PRE-GROUND COFFEE
MAXIMUM ONE MEASURE
A LONG coffee with pre-ground coffee has been Place pre-ground coffee in the funnel (A4) (fig.
requested
13) and press “ OK” to continue and complete delivery.
OK
FILL BEANS CONTAINER
The coffee beans have run out.
Fill the beans container (A3) (fig. 11).
The pre-ground coffee funnel (A4) is clogged.
Empty the funnel with the help of the brush
(C5) as described in section “16.8 Cleaning the
pre-ground coffee funnel”.
ESC
25
GROUND TOO FINE. ADJUST
MILL 1 CLICK WHILE IN
OPERATION
The grinding is too fine and the coffee is delive- Repeat coffee delivery and turn the grinding adjustment dial (A5) (fig. 13) one click
red too slowly or not at all.
clockwise towards “7” while the coffee mill is
in operation. If after making at least 2 coffees
delivery is still too slow, repeat the correction
procedure, turning the grinding adjustment
dial another click until delivery is correct (see
section “9.3 Adjusting the coffee mill”). If the
problem persists, make sure the water tank
(A16) is fully inserted.
If the water softener filter (C4) is present, an Insert the hot water/steam spout (C6) in the
air bubble may have been released inside the appliance and deliver a little water until the
circuit, obstructing delivery.
flow becomes regular.
ESC
SELECT A MILDER TASTE
OR REDUCE PRE-GROUND
COFFEE QUANTITY
Too much coffee has been used.
Select a milder taste by pressing “
AROMA” (B6) or reduce the quantity of preground coffee (maximum 1 measure).
INSERT WATER SPOUT
The hot water spout (C6) is not inserted or is
inserted incorrectly
Insert the water spout as far as it will go.
INSERT MILK CONTAINER
The milk container (D) is not inserted correctly. Insert the milk container as far as it will go (fig.
18).
INSERT INFUSER ASSEMBLY
The infuser (A19) has not been replaced after Insert the infuser as described in section “16.9
cleaning.
Cleaning the infuser”.
ESC
PUSH
26
PRESS OK TO START FILLING
PROCESS
The water circuit is empty
Press “ OK” to deliver water from the spout
(C6) until it flows out normally.
If the problem persists, make sure the water
tank (A16) is fully inserted.
The milk container has been inserted with
the froth adjustment dial (D1) in the “CLEAN”
position.
To proceed with the CLEAN function press “
OK”, or turn the froth adjustment dial to one of
the milk positions.
OK
PRESS OK TO START CLEANING
PROCESS OR TURN MILK
FROTH ADJUSTMENT DIAL
OK
TURN DIAL TO <CLEAN> POSI- Milk has been delivered recently and the tubes
TION TO START CLEANING
inside the milk container must be cleaned (D).
Turn the froth adjustment dial (D1) to CLEAN
(fig. 20).
CLEAN
ESC
TURN THE MILK FROTH
ADJUSTMENT DIAL TO MILK
POSITION
The milk container has been inserted with
the froth adjustment dial (D1) in the “CLEAN”
position.
Turn the dial to the required froth position.
DESCALING NEEDED PRESS
OK TO START (~40MIN)
The machine must be descaled.
Press “ OK” to start descaling or “ ESC”
to descale later. The descaling procedure described in section “17. Descaling” needs to be performed as soon as possible.
ESC
OK
27
REPLACE WATER SOFTENER FIL- The water softener filter (C4) is exhausted.
TER PRESS OK TO START
ESC
Press “ OK” to replace or remove the filter,
or “ ESC” to carry out the procedure later.
Follow the instructions in section “19. Water
softener filter”.
OK
GENERAL ALARM. REFER
TO USER MANUAL / SMART
COFFEE APP
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly,
as described in section “16. Cleaning”. If the
message is still displayed after cleaning, contact a service centre.
The appliance needs descaling and/or the filter The descaling procedure described in section
(C4) must be replaced.
“17. Descaling” needs to be performed and/or
the filter needs replacing or removing as described in section “19. Water softener filter”.
The tubes inside the milk container (C) must be Turn the froth adjustment dial (D1) to CLEAN
cleaned.
(fig. 20).
The filter (C4) must be replaced.
Replace or remove the filter as described in
section “19. Water softener filter”.
The machine must be descaled.
The descaling procedure described in section
“17. Descaling” needs to be performed as soon
as possible.
The auto-start function is enabled.
To disable the function, proceed as described in
section “8.6 Auto-start ”.
Energy saving is enabled.
To disable energy saving, proceed as described
in section “8.9 Energy saving
The appliance is connected to a device via
bluetooth.
28
”.
23.
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The coffee is not hot.
The cups were not preheated.
Warm the cups by rinsing them with hot
water (Please note: you can use the hot water
function).
The infuser has cooled down because Before making the coffee, heat the infuser by
2/3 minutes have elapsed since the last rinsing using the rinse function (see section
”).
coffee was made.
“8.1 Rinsing
A low coffee temperature is set.
The coffee is weak or not creamy The coffee is ground too coarsely.
enough.
The coffee is unsuitable.
Set a higher coffee temperature in the menu
(see section “8.10 Coffee temperature ” ).
Turn the grinding adjustment dial (A5) one
click anticlockwise towards “1” while the coffee mill is in operation (fig. 10). Continue one
click at a time until coffee delivery is satisfactory. The effect is only visible after delivering
2 coffees (see section “9.3. Adjusting the coffee
mill”).
Use pre-ground coffee for espresso machines.
The coffee is delivered too slowly or a The coffee is ground too finely.
drop at a time.
Turn the grinding adjustment dial (A5) one
click clockwise towards “7” while the coffee
mill is in operation (fig. 10). Continue one click
at a time until coffee delivery is satisfactory.
The effect is only visible after delivering 2
coffees (see section “9.3. Adjusting the coffee
mill”).
Coffee does not come out of one or The coffee spouts (A8) are blocked.
both of the spouts.
Clean the spouts with a toothpick (fig. 36B).
The appliance does not come on
The power cord (C8) connector is not Insert the connector as far as it will go in the
inserted correctly.
socket at the back of the appliance (fig. 1).
It is not plugged into the mains socket. Plug into the mains socket (fig. 1).
The main switch (A21) is not turned on. Press the main switch (fig. 2).
The infuser cannot be extracted
The appliance has not been turned off Turn the appliance off by pressing the
correctly
(see section “7. Turning off”).
(A7)
The milk does not come out of the The lid (D2) of the milk container lid Clean the milk container lid as described in secmilk spout (D5)
(D) is dirty
tion “16.10 Cleaning the milk container”.
29
The milk contains large bubbles and The milk is not cold enough or is not Use skimmed or semi-skimmed milk at refrigesquirts out of the milk spout (D5) or semi-skimmed.
rator temperature (about 5° C). If the result is
there is little froth
not as you wished, try changing brand of milk.
The froth adjustment dial (D1) is incor- Adjust following the instructions in section
rectly adjusted.
“10. Making cappuccinos and milk-based
coffees”.
The milk container lid (D2) or froth Clean the milk container lid and dial as deadjustment dial (D1) are dirty.
scribed in section “16.10 Cleaning the milk
container”.
The hot water/steam connection noz- Clean the connection nozzle as described in
zle (A9) is dirty
section “16.11 Cleaning the hot water/steam
connection nozzle”.
The cup warmer is hot, even though it A number of drinks have been prepared
has been disabled
in rapid succession
The chocolate is not sufficiently dense The hot chocolate powder used does Change the type of powder used.
not contain thickener.
The highest density has not been se- Select the highest density in the corresponding screen.
lected.
The quantities of milk and hot chocola- Follow the instructions in section "11. Making
te powder are not correct.
hot chocolate"
The chocolate is cold or there are
lumps
The stirrer (E4) and steam spout (E3) Insert the stirrer and steam spout on the funare not inserted correctly in the funnel nel.
(E2).
The instructions have not been follo- Pour the milk/water into the funnel (E2) first,
wed.
followed by the hot chocolate powder.
During cleaning, there are traces of
black on the stirrer (E4)
The magnets in the stirrer attract traces Clean as described in section "16.12 Cleaning
of iron naturally present in the hot cho- the hot chocolate carafe (E)".
colate powder.
30
24. ELECTRICAL REQUIREMENTS (UK ONLY)
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt
about your supply contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined
below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and
plug it into a supply socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in use.
IMPORTANT: the wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth
GREEN AND YELLOW
BLUE
BROWN
EARTH
NEUTRAL
LIVE
13 amp
Fuse
Blue to
neutral
Brown to
live
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth
or coloured green or green and yellow.
symbol
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the
plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced
with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a replacement cover is
obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. Always
state this colour when ordering a replacement fuse cover. Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
31
Download PDF
Similar pages