knox freestanding tub faucet

KNOX FREESTANDING TUB FAUCET
INSTALLATION INSTRUCTIONS
Before you begin, read the installation instructions below.
Observe all local plumbing and building codes.
For the following installation instructions for your new
freestanding tub faucet it is assumed that the water supply lines
are in place underneath the floor and are directly accessible for
faucet installation.
3"
7-7/8"
Installation on a concrete slab is not recommended.
36"
Unpack and inspect faucet for any shipping damages and
ensure that none of the required pieces are missing. If you
find any damages, do not install. Contact Customer Service at
1-866-855-2284. If you need assistance while installing your
new freestanding tub faucet, call our Customer Service number.
We recommend consulting a professional if you are unfamiliar
with installing bathroom fixtures and plumbing. Signature
Hardware accepts no liability for any damages to the floor,
walls, plumbing or personal injury during installation.
1"-2"
Shut off the water supply lines at the tub where the new faucet
is being installed.
1/2"
1/2"
1"
TOOLS AND MATERIALS:
Level
Teflon
Drill
Pencil
6mm Hex Wrench
(provided)
Goggles
2.5mm Hex Wrench
(provided)
Adjustable Wrench
Knox Freestanding Tub Faucet Installation Instructions
1
1. Use the inlet base to mark the mounting hole
locations. Drill mounting holes in the 2 holes on the
floor.
Note: The base is marked to indicate the inlets for
hot and cold water.
2. Attach 4 expansion bolts to the inlet base. Tighten
with hex nut to secure.
Hex Nut
Protective Cover
3"
3"
Inlet Base
Spring Washer
Flat Washer
Mounting Hole
Expansion Bolt
3. Insert the expansion bolts into the mounting holes.
Adjust the top surface of the inlet base to a level
position and tighten hex nuts.
Note: The cold water inlet should be facing the
bathtub.
4. Wrap the connections with teflon tape and connect
the inlet base to the hot and cold water supply pipes.
Remove the protective cover and insert a plug into
the base outlet and attach the base flange with
counter bore facing upward.
Hex Wrench
Locking Screw
Level
Base Flange
Side to Side
BS立柱浴缸龙头
Top to Bottom
Cold Water Inlet
Plug
Hot Water Inlet
Knox Freestanding Tub Faucet Installation Instructions
2
5. Turn on the water supply to test the water pressure
and ensure the each connection is tight (no water
should be leaking).
6. Unthread the locking screw to remove the flange
and plug.
Cold Water Inlet
Hot Water Inlet
7. Place on protective cover back on the base and
complete flooring installation.
Note: The finished floor should be level or slightly
higher than the top of the protective cover.
8. Remove the protective cover from the inner pipe
on the faucet body. Slide the escutcheon onto the
faucet body and secure it to the faucet flange with
locking screws.
Faucet Body
Inner Pipe
Protective Cover
Escutcheon
Knox Freestanding Tub Faucet Installation Instructions
3
9. Remove the protective cover and insert the inner pipe
into inlet base outlet. Attach the faucet flange to the
base with locking screws. Tighten with a hex wrench to
secure. Slide the escutcheon down the faucet body to
the finished floor.
10. Connect hand shower and faucet body with hand
shower hose.
BS立柱浴缸龙头
11. When the faucet is installed turn on the water supply,
check to make sure that all connections are tight and
that the hot and cold supplies are working correctly.
12. Divert the water to the hand shower and allow the
water to flow through the hose for approximately 60
seconds.
Hot
Cold
Knox Freestanding Tub Faucet Installation Instructions
4
Download PDF
Similar pages