Brew Max - Watts Water Technologies

ES-HS-Brew Max
For Foodservice Applications
Job Name –––––––––––––––––––––––––––––––––––––––––––– Contractor –––––––––––––––––––––––––––––––––––––––––––––
Job Location –––––––––––––––––––––––––––––––––––––––––– Approval ––––––––––––––––––––––––––––––––––––––––––––––
Engineer –––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. –––––––––––––––––––––––––––––––––––
Approval –––––––––––––––––––––––––––––––––––––––––––––– Representative –––––––––––––––––––––––––––––––––––––––––
Series Brew Max
Brew Station Filtration Systems
Flow Rate:
Brew Max-S2: Maximum 0.5 GPM (1.9 LPM)
Brew Max-S2L: Maximum 1 GPM (3.8 LPM)
Hydro-Safe Brew Max systems have been specifically engineered to address and correct multiple water related problems
for brew stations. Incorporating both high end coconut shell
carbon filtration with OneFlow® media for scale control, these
systems deliver superior filtration while providing advanced scale
protection. Advanced carbon filtration for the reduction of lead,
cyst and VOC in addition to chlorine taste and odor providing a
superior consistent quality beverage.
Brew Max-S2
•Coffee Brewers
•Tea Machines
• Soda Machines
•Increases brew machine life, performance and quality
•Reduces scale build-up
•Reduces lead, cyst, VOC's, sediment, chlorine taste and odor
•Reduces maintenance and system downtime
•Consistent quality and better tasting drinks
•In/Out valves allow for easy filter service
•Pressure gauges and flush kit included
• Easy to install
•Simple filter replacement
System Specifications
Maximum Pressure: 125psi/8.6 bar
Maximum Temperature: 100°F/38°C
pH 6.5 to 8.5
Hardness (maximum for systems containing OneFlow) 75 grains
(1282 ppm CaCO3)
Chlorine < 2ppm
Iron (maximum) 0.3 mg/l
Manganese (maximum) 0.05 mg/l
Copper (for systems containing OneFlow) < 0.1 mg/l
Oil & H2S- None allowed
Polyphosphate (for systems containing OneFlow)- None allowed
Silica (maximum for systems containing OneFlow) 10ppm
For all other feed water quality requirements abide by the
current USEPA Safe Drinking Water Act standards.
Brew Max-S2L
Brew Max Systems are Tested and Certified by WQA
to NSF/ANSI Standard 42 and 53 for the reduction
of claims specified on the Performance Data Sheet &
NSF/ANSI 372 for "lead free" compliance.
Please note: Cartridge capacities are estimates and may be
less depending on incoming water quality.
Note: Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before or after
the system.
* The wetted surface of this product contacted by consumable
water contains less than 0.25% of lead by weight.
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,
please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
System Specifications cont.
Filter Cartridge Life Span
Inlet/Outlet Connections: 3/8" NPT
Filter cartridges should be changed at end of filter life, due to lack of
filtering performance, or whenever a 15 psi pressure drop or greater
is experienced during normal operation, whichever comes first.
OneFlow® Application Practices
Note: Systems using OneFlow technology prevent hardness related
scale formation inside the plumbing system at influent hardness
levels of 75 grains per gallon of calcium carbonate and less. Due to
variances in water chemistry certain aesthetic conditions external of
the plumbing system may not be attained. New copper lines need
to be passivized before placing unit into service. Copper usually
originates from new copper plumbing upstream of the OneFlow
system. All new copper plumbing before the system should be allowed to passivate by operating under normal conditions for a period
of 4 weeks prior to starting the system up. This will allow the copper
surfaces to be fully flushed and develop a natural protective surface.
To further minimize any problem with excess copper, avoid applying
excess flux on the inner surfaces of the pipe and use a low-corrosivity water soluble flux listed under the ASTM B813 standard. OneFlow
is not for use on closed loop systems.
System Replacement Filters
System Model
Filter Ordering Code
All Filters for System
6 Months
10" Coconut Shell
Carbon Block
12 Months
10" OneFlow Anti-Scale
6 Months
10" Phosphate Scale
Control (Option)
Brew Max-S2
All Filters for System
System Model
Ordering Code
Max Flow Rate
Connection Size
Brew Max-S2
0.5 GPM (1.9 LPM)
3/8" NPT
Brew Max-S2L
1 GPM (3.8 LPM)
3/8" NPT
6 Months
20" Coconut Shell
Carbon Block
12 Months
20" OneFlow Anti-Scale
6 Months
20" Phosphate Scale
Control (Option)
Brew Max-S2L
System Diagrams
Brew Max-S2
Brew Max-S2L
Note: Allow 3" of clearance at bottom of system for removal of filter bowls for filter cartridge replacement
A Watts Water Technologies Company
ES-HS-Brew Max 1211
Tel: (800) 264-1183 • Fax: (724) 733-4808 •
© 2012 Watts
Download PDF
Similar pages