LAST UPDATE 22/03/2018
TECHNICAL DATA SHEET ART. S.1068W - MINIFOCUS
9 MODULES LED 3000K 230V 2313lm 28.4W CRI 90 MacAdam step 3
Rated luminaire luminous flux: 1972lm
Rated input power: 30W
Luminaire efficacy: 66lm/W
Electronic ballast 220÷240V 0/50/60Hz
IP 66
Fixture available with integral DALI driver on request with surcharge.
PRODUCT TYPE
Projector. IP rating IP 66
MATERIAL CHARACTERISTICS
Aluminium die cast housing in EN AB-47100 (low copper content) with high resistance against corrosion. Stone wash surface treatment prior to painting process. A4 grade
Stainless Steel screws with 2,5-3% molybdenum content which increases the resistance against corrosion. Pre treated Silicone Gaskets. Painting Process : 3 Step
Process
1) Surface treatment with BONDERITE. A heavy metal free chemical surface treatment containing ceramic nano particles giving a cohesive, inorganic and highly dense
protective coating. 2) PRE POLYMERIZATION a process of introducing an epoxy primer with excellent characteristics to the paint which also offers very high resistance to
oxidation due to its Zinc content. 3) POLYMERIZATION a process with the application of polyester powder with high resistance against UV rays and harsh weather
conditions. Resistance test protection for Marine applications for 1200h. The 5 mm thick tempered glass diffuser is fixed to the external body by a silicon resin and
positioned flush with the support ring. Mechanical resistance IK 10 Maximum load capacity -LIGHTING PERFORMANCE
The lathed anodized reflector is composed of 99,98% pure anodized aluminium with a bright polish finish (Version with LED COB). LOR -INSTALLATION AND MAINTENANCE
The projector is supplied with graduated ferrules in AISI 316L stainless steel on both sides of the fitting. The screws that fix the front glass holder to the main body of the
projector are also in AISI 316L stainless steel with anti loss washers . The glass diffuser and front support ring are secured to the body of the projector by a pivoting hinge
assembly that when opened allows for easy access to the lamp and the reflector.
WIRING
Double cable entries with PG13,5 (Ø 6÷12 mm) cable glands in nickeled brass. Isolation: CLASS I . Available colours: Aluminium grey (cod.14). Weight: 3.9 Kg Glow Wire
test: 960°C
L.E.D circuit included.
MINIFOCUS REGISTERED DESIGN
This luminaire contains built-in LED modules with energy class: A, A+, A++. In case of damage or malfunction please contact the manufacturer to receive
additional instructions on how to replace and relative spare parts to order. The LED modules cannot be handled in the luminaire by the end user (Regulation
UE 874/2012).
LED circuit boards are engineered accordingly to actual Lumen Maintenance regulation (LM80) and Technical Memorandum (TM21) where uniformity and
quality of light is 50.000 hours referred to L70 B20 Ta 25°C.
Lifecycle refers to LED circuit boards only, all others components of the luminaire are excluded.
EMERGENCY VERSIONS
The fittings operates both on AC ( 50/60Hz ) and DC ( 0Hz ) voltage.
SIMES S.p.A. - Via G.Pastore 2/4 - 25040 - Corte Franca - BRESCIA (ITALY) - http://www.simes.com - e-mail: simes@simes.com
Export Sales: Tel. +39 0309860440 - Fax +39 0309860449 / Technical Dep.: Tel. +39 0309860450 - Fax +39 0309860459 / Lighting Design Dep.:Tel. +39 0309860425 - Fax +39 0309860429
The present technical data sheet and all the information contained is property of SIMES S.p.A. All rights reserved.
We reserve the right to change specifications without prior written notice.
1/6
LAST UPDATE 22/03/2018
TECHNICAL DATA SHEET ART. S.1068W - MINIFOCUS
ACCESSORIES
S.1013
FLANGE FOR POLE INSTALLATION Ø 120mm
Flange in die-cast aluminium suitable only for Ø 120 mm
poles. The flange can be used for maximum 2 projectors,
one for each side.
S.1022
VISOR
Colour: black (code 09).
S.1023
ADJUSTABLE BARN DOORS
Every box S.1023 contains only one flap. To receive the
complete system of 4 flaps you have to order n°4 S.1023.
Colour: black (code 09).
S.1005
STAKE
In POLYPROPYLENE.
Colour: black (code .09). The 100 mm upper part must
stay above ground level, according to the norm.
Available until 31/12/2017 but subject to stock levels
S.1016
FLANGE FOR POLE Ø 60mm INSTALLATION
Die-cast aluminium flange suitable only for Ø 60 mm
poles. To install the flange on Ø 76mm pole the screws
kit SACVITFOCTOWER2 must be purchased separately.
The flange can be used for maximum 2 projectors, one
for each side.
Product is suitable for installation on SIMES poles Ø
60mm Art.S.2842-S.2843 and Ø 76mm S.2844-S.2845
S.2842
Ø60mm CYLINDRICAL POLE TO BE BURIED
Cylindrical shaped poles consisting of: straight circular
section shaft, Ø 60mm, 4mm in thickness, total length
4,00m , single section built by using longitudinally welded
tubes by induction welding (ERW) UNI EN 10219-2-ISO
4200
Suitable for ground recessed installation to a cement
base 0,50m : Suggested reinforced concrete footstall
dimension 0,7m x 0,7m h 0,7m. Footstall dimension can
be calculated according to your country norms and
ground properties.
The grade of steel used is S235JR (Fe360B) with
material characteristics as per normative UNI EN 10025;
The surface protection treatment is done through hot dip
galvanization.
Painting Process: PRE POLYMERIZATION a process of
introducing an epoxy primer with excellent characteristics
to the paint which also offers very high resistance to
oxidation due to its Zinc content. POLYMERIZATION a
process with the application of polyester powder with high
resistance against UV rays and harsh weather conditions.
Resistance test protection for Marine applications for
1500h.
S.2843
Ø60mm CYLINDRICAL POLE WITH BASE
Cylindrical shaped poles consisting of: straight circular
section shaft, Ø 60mm, 4mm in thickness, total length
3,50m , single section built by using longitudinally welded
tubes by induction welding (ERW) UNI EN 10219-2-ISO
4200
Suitable for installation to a planted root flange through a
base plate in steel S355JO Footstall dimension can be
calculated according to your country norms and ground
properties.
The grade of steel used is S235JR (Fe360B) with
material characteristics as per normative UNI EN 10025;
The surface protection treatment is done through hot dip
galvanization.
Painting Process: PRE POLYMERIZATION a process of
introducing an epoxy primer with excellent characteristics
to the paint which also offers very high resistance to
oxidation due to its Zinc content. POLYMERIZATION a
process with the application of polyester powder with high
resistance against UV rays and harsh weather conditions.
Resistance test protection for Marine applications for
1500h.
TO BE USED WITH THE FOLLOWING ACCESSORIES:
S.2849 PLANTED ROOT for CYLINDRICAL POLE
S.2849
PLANTED ROOT for CYLINDRICAL POLE
C= 200mm, D=200mm E=Ø80mm, h=407mm, h1=90mm
and bolts in galvanized steel with M16 threads.
Suggested reinforced concrete footstall dimension **:
A = 0.7 m
B = 0.7 m
S.2809
POLE BASE COVER
For pole with base and pole to be buried Ø102mm or
Ø120mm.
Die-cast aluminium housing.
S.2826
Ø 120mm CYLINDRICAL POLE TO BE BURIED
Cylindrical shaped poles consisting of: straight circular
section shaft, Ø 120mm, 3mm in thickness, total length
4,80m , single section built by using longitudinally welded
tubes by induction welding (ERW) UNI EN 10219-2-ISO
**Footstall dimension can be calculated according to your
country norms and ground properties.
TO BE USED WITH THE FOLLOWING ACCESSORIES:
S.2800, S.2801, S.2812, S.2813, S.2843, S.2845
CYLINDRICAL POLE
SIMES S.p.A. - Via G.Pastore 2/4 - 25040 - Corte Franca - BRESCIA (ITALY) - http://www.simes.com - e-mail: simes@simes.com
Export Sales: Tel. +39 0309860440 - Fax +39 0309860449 / Technical Dep.: Tel. +39 0309860450 - Fax +39 0309860459 / Lighting Design Dep.:Tel. +39 0309860425 - Fax +39 0309860429
The present technical data sheet and all the information contained is property of SIMES S.p.A. All rights reserved.
We reserve the right to change specifications without prior written notice.
2/6
4200
Suitable for ground recessed installation to a cement
base 0,60m : Suggested reinforced concrete footstall
dimension 0,8m x 0,8m h 0,8m. Footstall dimension can
be calculated according to your country norms and
ground properties.
The grade of steel used is S235JR (Fe360B) with
material characteristics as per normative UNI EN 10025;
The surface protection treatment is done through hot dip
galvanization.
Painting Process: PRE POLYMERIZATION a process of
introducing an epoxy primer with excellent characteristics
to the paint which also offers very high resistance to
oxidation due to its Zinc content. POLYMERIZATION a
process with the application of polyester powder with high
resistance against UV rays and harsh weather conditions.
Resistance test protection for Marine applications for
1500h.
Including inspection door, terminal cable block and fuse.
Cap COPE2826PVC.09 already installed.
TO BE USED WITH THE FOLLOWING ACCESSORIES:
S.2809 POLE BASE COVER
3/6
S.2846
Ø 120mm CYLINDRICAL POLE WITH BASE
Cylindrical shaped poles consisting of: straight circular
section shaft, Ø 120mm, 3mm in thickness, total length
4,20m , single section built by using longitudinally welded
tubes by induction welding (ERW) UNI EN 10219-2-ISO
4200
Suitable for installation to a planted root flange through a
base plate 250mm x250mm x12mm in steel S355JO :
Suggested reinforced concrete footstall dimension 1m x
1m h 0,7m. Footstall dimension can be calculated
according to your country norms and ground properties.
The grade of steel used is S235JR (Fe360B) with
material characteristics as per normative UNI EN 10025;
The surface protection treatment is done through hot dip
galvanization.
Painting Process: PRE POLYMERIZATION a process of
introducing an epoxy primer with excellent characteristics
to the paint which also offers very high resistance to
oxidation due to its Zinc content. POLYMERIZATION a
process with the application of polyester powder with high
resistance against UV rays and harsh weather conditions.
Resistance test protection for Marine applications for
1500h.
Including inspection door, terminal cable block and fuse.
Cap COPE2826PVC.09 already installed.
TO BE USED WITH THE FOLLOWING ACCESSORIES:
S.2840 PLANTED ROOT for CYLINDRICAL POLE
4/6
S.2848
Ø 120mm CYLINDRICAL POLE WITH BASE
Cylindrical shaped poles consisting of: straight circular
section shaft, Ø 120mm, 3mm in thickness, total length
6,00m , single section built by using longitudinally welded
tubes by induction welding (ERW) UNI EN 10219-2-ISO
4200
Suitable for installation to a planted root flange through a
base plate 250x250x12mm in steel S355JO : Suggested
reinforced concrete footstall dimension 1x1 h 0,7m.
Footstall dimension can be calculated according to your
country norms and ground properties.
The grade of steel used is S235JR (Fe360B) with
material characteristics as per normative UNI EN 10025;
The surface protection treatment is done through hot dip
galvanization.
Painting Process: PRE POLYMERIZATION a process of
introducing an epoxy primer with excellent characteristics
to the paint which also offers very high resistance to
oxidation due to its Zinc content. POLYMERIZATION a
process with the application of polyester powder with high
resistance against UV rays and harsh weather conditions.
Resistance test protection for Marine applications for
1500h.
MINISLOT AVANT-GARDE INSTALLED ON S.2848
POLE:
Finished product total height = 7.13 m
Cap COPE2826PVC.09 already installed.
TO BE USED WITH THE FOLLOWING ACCESSORIES:
S.2840 PLANTED ROOT for CYLINDRICAL POLE
S.2809 POLE BASE COVER
S.2840
PLANTED ROOT for CYLINDRICAL POLE
h = 470 mm and bolts in galvanized steel with M16
threads.
Suggested reinforced concrete footstall
dimension:
A = 0.7 m
B=1 m
Footstall dimension can be calculated according to your
country norms and ground properties.
Footstall dimension can be calculated according to your
country norms and ground properties.
TO BE USED WITH THE FOLLOWING ACCESSORIES:
S.2846, S.2848 CYLINDRICAL POLE
S.2812
Ø 76 mm CYLINDRICAL POLE TO BE BURIED
Cylindrical shaped poles consisting of: straight circular
section shaft, Ø 76mm, 3mm in thickness, total length
3,50m, single section built by using longitudinally welded
tubes by induction welding (ERW) UNI EN 10219-2-ISO
4200
Suitable for ground recessed installation to a cement
base 0,50m: Suggested reinforced concrete footstall
dimension 1m x1m h 0,7m. Footstall dimension can be
calculated according to your country norms and ground
properties.
The grade of steel used is S235JR (Fe360B) with
material characteristics as per normative UNI EN 10025;
Painting Process: PRE POLYMERIZATION a process of
introducing an epoxy primer with excellent characteristics
to the paint which also offers very high resistance to
oxidation due to its Zinc content. POLYMERIZATION a
process with the application of polyester powder with high
resistance against UV rays and harsh weather conditions.
Resistance test protection for Marine applications for
1500h.
Including inspection door, terminal cable block and fuse.
5/6
LAST UPDATE 22/03/2018
TECHNICAL DATA SHEET ART. S.1068W - MINIFOCUS
ACCESSORIES
S.2813
Ø 76mm CYLINDRICAL POLE WITH BASE
Cylindrical shaped poles consisting of: straight circular
section shaft, Ø 76mm, 3mm in thickness, total length
3,00m , single section built by using longitudinally welded
tubes by induction welding (ERW) UNI EN 10219-2-ISO
4200
Suitable for installation to a planted root flange through a
base plate 250mm x250mm x12mm in steel S355JO :
Suggested reinforced concrete footstall dimension 1m x
1m h 0,7m. Footstall dimension can be calculated
according to your country norms and ground properties.
The grade of steel used is S235JR (Fe360B) with
material characteristics as per normative UNI EN 10025;
The surface protection treatment is done through hot dip
galvanization.
Painting Process: PRE POLYMERIZATION a process of
introducing an epoxy primer with excellent characteristics
to the paint which also offers very high resistance to
oxidation due to its Zinc content. POLYMERIZATION a
process with the application of polyester powder with high
resistance against UV rays and harsh weather conditions.
Resistance test protection for Marine applications for
1500h.
Including inspection door, terminal cable block and fuse.
TO BE USED WITH THE FOLLOWING ACCESSORIES:
S.2849 PLANTED ROOT for CYLINDRICAL POLE
Further information
FIXING BASE
SIMES S.p.A. - Via G.Pastore 2/4 - 25040 - Corte Franca - BRESCIA (ITALY) - http://www.simes.com - e-mail: simes@simes.com
Export Sales: Tel. +39 0309860440 - Fax +39 0309860449 / Technical Dep.: Tel. +39 0309860450 - Fax +39 0309860459 / Lighting Design Dep.:Tel. +39 0309860425 - Fax +39 0309860429
The present technical data sheet and all the information contained is property of SIMES S.p.A. All rights reserved.
We reserve the right to change specifications without prior written notice.
6/6
Download PDF
Similar pages