GrandBed TEMPUR Advanced Ergo System

GrandBed TEMPUR® Advanced Ergo System™
COMPLETE REFERENCE GUIDE
U.S. Patent No. 7,321,811 and other patents pending
© 2011 Tempur-Pedic Management, Inc. All Rights Reserved.
TPNA-CRG-GBTAES-0111
GrandBed TEMPUR® Advanced Ergo System™
20-YEAR LIMITED WARRANTY
TEMPUR-PEDIC NORTH AMERICA, INC. (“TEMPUR-PEDIC”) GUARANTEES THAT WE WILL, AT TEMPUR-PEDIC’S OPTION,
REPLACE OR REPAIR PURCHASER’S GRANDBED TEMPUR® ADVANCED ERGO SYSTEM™ IF IT IS DEFECTIVE DUE TO FAULTY
WORKMANSHIP OR MATERIALS, SUBJECT TO THE LIMITATIONS DESCRIBED IN THIS WARRANTY.
YEAR 1 - FULL COVERAGE OF PARTS AND LABOR
Your GrandBed TEMPUR® Advanced Ergo System™ is warranted against defects in the workmanship or materials for a period of one (1) year from
the warranty commencement date. Electronics, electrical components, drive motors and massage motors are included. Upon notice during the first
year from the warranty commencement date, Tempur-Pedic will send replacement parts (at no cost to the purchaser) for any defective part to the
purchaser, and Tempur-Pedic will pay all authorized labor and transportation costs associated with the repair or replacement of any parts Tempur-Pedic
determines to be defective. This one (1) year warranty shall not apply if purchaser does not return any and all defective parts to Tempur-Pedic within 15
days of purchaser’s receipt of replacement part.
YEARS 2 AND 3 – FULL COVERAGE OF PARTS ONLY
Upon notice during the years two and three (2 - 3) from the warranty commencement date, Tempur-Pedic will offer replacement parts for any
defective part to the purchaser. Electronics, electrical components, drive motors and massage motors are included. This two (2) year warranty shall not
apply if purchaser does not return any and all defective parts to Tempur-Pedic within 15 days of purchaser’s receipt of replacement part. Purchaser shall
bear all service, transportation, labor, and shipping costs related to the delivery and/or replacement of the defective part.
YEARS 4 THROUGH 20 – PRORATED COVERAGE OF PARTS ONLY
Upon notice during the fourth through the twentieth (4 – 20) years from the warranty commencement date, Tempur-Pedic will offer replacement
parts (upon terms and conditions set forth in this paragraph) for any mechanical bed part found to be defective. Electronics, electrical components,
drive motors and massage motors are excluded. Purchaser shall pay 1/17th of the then current replacement cost of the defective part multiplied
by the number of years after three (3) years from the warranty commencement date, and Tempur-Pedic shall bear the remainder of the cost of the
replacement part. This seventeen (17) year warranty shall not apply if purchaser does not return any and all defective parts to Tempur-Pedic within 15
days of purchaser’s receipt of replacement part. Purchaser shall bear all service, transportation, labor, and shipping costs related to the delivery and/
or replacement of the defective part. After the 20th year, purchaser shall bear the entire cost of repair and replacement of all parts and materials,
including labor and transportation.
ADDITIONAL TERMS AND CONDITIONS
This warranty does not apply; (a) to any damage caused by the purchaser; (b) if there has been any unauthorized repair or replacement of the unit’s
parts; (c) if the unit has been mishandled (whether in transit or by other means), subjected to physical or electrical abuse or misuse, or otherwise
operated in any way inconsistent with the operation and maintenance procedures outlined in the Complete Reference Guide, this warranty, and any
other applicable document published or approved by Tempur-Pedic; (d) to damage to mattresses, fabric, cables, electrical cords or items supplied by
Resellers. Contact the Reseller or relevant party for warranty information on these items.; (e) if there has been any unnecessary service calls, including
costs for in-home service calls solely for the purpose of educating the consumer about the unit for finding an unsatisfactory power connection; (g) if
the recommended weight restrictions are not followed (Twin, Twin Long, Split/Dual Queen, Split/Dual CA King – 300 lbs.; Double, Double Long – 375
lbs.; Queen – 425 lbs.), the warranty will be void.
Repairs to or replacement of the GrandBed TEMPUR® Advanced Ergo System™ or its components under the terms of this limited warranty will apply to
the original warranty period and will not serve to extend such period.
The decision to repair or to replace defective parts under this warranty shall be made, or case to be made, by Tempur-Pedic at its option and in its sole
discretion.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE PURCHASER. THERE SHALL BE NO LIABILITY ON THE PART OF TEMPUR-PEDIC
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR FOR ANY OTHER DAMAGE, CLAIM, OR LOSS NOT EXPRESSLY
COVERED BY THE TERMS OF THIS WARRANTY. THIS LIMITED WARRANTY DOES NOT INCLUDE REIMBURSEMENT FOR INCONVENIENCE, REMOVAL,
INSTALLATION, SETUP TIME, LOSS OF USE, SHIPPING, OR ANY OTHER COSTS OR EXPENSES. TEMPUR-PEDIC MAKES NO OTHER WARRANTY
WHATSOEVER, EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED BY TEMPUR-PEDIC AND EXCLUDED FROM THIS AGREEMENT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to
every purchaser. This warranty gives the purchaser specific legal rights, and the purchaser may also have other rights, which may vary from state to
state. This warranty is valid in all 50 states, Puerto Rico, and Canada. This warranty is valid only for the original purchaser of the product. An original
purchaser is one who purchases the product directly from Tempur-Pedic North America, Inc. or an authorized Reseller of Tempur-Pedic North America,
Inc. If you are not the original purchaser of this product, you take it “as is” and “with all faults.” If you did not purchase this GrandBed TEMPUR®
Advanced Ergo System™ directly from Tempur-Pedic North America, Inc., we will require proof of purchase from you demonstrating that you are the
original purchaser and eligible to make a valid claim under this warranty. This warranty begins on the “warranty commencement date” which is the
date of purchase for new unused units, and the date of manufacture for units that have been used as floor or display models. Thus, on a floor model
unit, the warranty is a portion of the limited 20-year warranty. If original proof of purchase is not provided by purchaser, Tempur-Pedic reserves the
right to determine if the unit is not covered by this warranty or to use the manufacturing date as the warranty commencement date. This limited
warranty gives you specific legal rights. You may also have other rights that vary from state to state.
If you experience any trouble with your GrandBed TEMPUR® Advanced Ergo System™ during the warranty period, please consult the troubleshooting
section of your Reference Guide. If problems persist after following these instructions, please call: 1-800-979-1457
PLEASE RETAIN THIS WARRANTY AND YOUR ORIGINAL PROOF OF PURCHASE FOR AT LEAST 20 YEARS FROM THE DATE OF PURCHASE.
2
GrandBed TEMPUR® Advanced Ergo System™
Table of Contents
SAFETY PRECAUTIONS............................................................................................... 4
COMMONLY ASKED QUESTIONS AND ANSWERS..................................................... 8
SPECIFICATIONS......................................................................................................... 9
INSTALLATION.......................................................................................................... 10
OPERATION
WIRELESS REMOTE CONTROL PROGRAMMING................................................ 15
WIRELESS REMOTE CONTROL FEATURES.......................................................... 16
OPERATING INSTRUCTIONS............................................................................... 17
TROUBLESHOOTING................................................................................................. 18
SERIAL NUMBER:
Customer Service: 1–800–979–1457
3
GrandBed TEMPUR® Advanced Ergo System™
SAFETY PRECAUTIONS
WARNING!
IMPORTANT SAFETY
INSTRUCTIONS.
PLEASE READ THESE
INSTRUCTIONS
THOROUGHLY BEFORE
USING THIS PRODUCT.
• Keep the cord away from heated surfaces.
SAVE THESE INSTRUCTIONS!
foot support (or other similar parts).
been designed to provide you with the reliable operation
Risk of electric shock — connect this furnishing to a
Your GrandBed TEMPUR® Advanced Ergo System™ has
and durability you expect. This product has been inspected
• Never operate the furnishing with the air openings blocked.
Keep the air openings free of lint, hair and the like.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are
being used or where oxygen is being administered.
• To disconnect, turn all controls to the off position, then
remove plug from outlet.
WARNING:
Risk of Injury — keep children away from extended
WARNING!
properly grounded outlet only. See grounding instructions.
and tested prior to shipment.
When using an electrical furnishing, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING YOUR
GRANDBED TEMPUR® ADVANCED ERGO SYSTEM™
.
DANGER:
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction
or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric
shock. This product is equipped with a cord having an
equipment-grounding conductor and a grounding plug.
To reduce the risk of electric shock:
The plug must be plugged into an appropriate outlet that
• Always unplug this furnishing from the electrical outlet
is properly installed and grounded in accordance with all
local codes and ordinances.
before cleaning.
WARNING:
DANGER
To reduce the risk of burns, fire, electric shock, or injury to persons:
Improper connection of the equipment-grounding
• Unplug from outlet before putting on or taking off parts.
conductor can result in a risk of electric shock. Check with
• Close supervision is necessary when this furnishing is
a qualified electrician or serviceman if you are in doubt
used by, or near children, invalids, or disabled persons.
as to whether the product is properly grounded. Do not
• Use this furnishing only for its intended use as described
modify the plug provided with the product. If it will not
in these instructions. Do not use attachments not
fit the outlet, have a proper outlet installed by a qualified
recommended by the manufacturer.
electrician.
• Never operate this furnishing if it has a damaged cord
or plug, is not working properly, has been dropped or
damaged, or dropped in water. Return the furnishing to
a service center for examination and repair.
SAVE THESE INSTRUCTIONS!
Customer Service: 1–800–979–1457
4
Safety Precautions
GROUNDING SAFETY
WARRANTY PRECAUTION!
This product is for use on a nominal 120-volt circuit, and
Do not open control box, motors or wireless remote
has a grounding plug that looks like the plug illustrated
control (with the exception of the battery compartments).
in sketch A (see figure below). A temporary adapter that
The warranty is void if these units are tampered with.
looks like the adapter illustrated in sketches B and C able
Any repair or replacement of Ergo System parts must be
to be used to connect this plug to a 2-pole receptacle as
performed by an authorized service person.
shown in sketch B if a properly grounded outlet is not
available. The temporary adapter should be used only until
a properly grounded outlet (sketch A) can be installed by
a qualified electrician. The green colored rigid ear, lug, or
the like extending from the adapter must be connected to
a permanent ground such as a properly grounded outlet
box cover. Whenever the adapter is used, it must be held
IN-HOME USE AND HOSPITAL DISCLAIMER
Your Ergo System is strictly designed for in-home use
only. It is NOT designed for hospital use and is NOT
designed to meet hospital standards. DO NOT USE this
bed with TENT TYPE oxygen therapy equipment or near
explosive gases.
WARNING:
in place by a metal screw.
This product is for use on a circuit having a nominal rating
DO NOT USE NEAR PEOPLE USING OR WEARING
of more than 120 volts and is factory equipped with a
MEDICAL DEVICES. FOR HOUSEHOLD / RESIDENTIAL USE
specific electric cord and plug to permit connection to
ONLY. DO NOT USE OUTDOORS.
a proper electric circuit. Make sure that the product is
This product conforms to UL STD 962.
connected to an outlet having the same configuration as
the plug. No adapter should be used with this product. If
the product must be reconnected for use on a different
type of electric circuit, the reconnection should be made
by qualified service personnel.
Unauthorized modifications could void the electrical
portion of your warranty. Failure to use a properly
grounded outlet for this product or modification of the
plug will compromise this important grounding safety
feature and may result in electrical shock, electrical fire, or
faulty operation of the product.
FOR BEST RESULTS, YOUR ERGO SYSTEM SHOULD BE
PLUGGED INTO A SURGE PROTECTOR (not included).
Customer Service: 1–800–979–1457
5
GrandBed TEMPUR® Advanced Ergo System™
IMPORTANT SAFETY FEATURES
The input transformer voltage is AC120V (1 Amp) 60HZ,
Use this furnishing only for its intended use as described
and the output voltage is DC24V (3 Amp). When there is
in these instructions. Do not use attachments not
a short-circuit, a fuse on the transformer will be blown in
recommended by the manufacturer.
order to protect the electrical equipment (Fuse: 1A~1.5A.).
If there is an overload weight condition on the head
or foot mechanism, the control unit will automatically
stop all functions. Once the excess weight is removed,
the control unit will automatically allow all functions to
resume operation after 30 seconds.
Should the above situation occur, the customer should
seek professional assistance by calling a licensed electrician
or by contacting customer service at 1-800-979-1457.
SMALL CHILDREN AND
PETS WARNING
For your safety, this Ergo System is equipped with special
After your Ergo System has been unboxed, immediately
locking casters. In order to prevent the movement of this
dispose of packaging as it can smother small children
product, all six casters should be in the locked position.
and pets. To avoid injury, children and pets should not
This can be accomplished by pushing down the locking
be allowed to play on or under the bed. Children should
latch on the caster. To resume mobility of the product, lift
not operate this product without adult supervision. Close
the locking latch up. You are strongly encouraged to place
supervision is necessary when this furnishing is used by, or
rubber caster cups or carpet squares under the casters
near children, invalids, or disabled persons.
in addition to locking them in place if the product is
positioned on a hard surface floor such as hardwood, tile
SAVE THESE INSTRUCTIONS!
or linoleum. Although the casters are locked and will not
Your Ergo System has been designed to provide
roll, they may slide.
you with the reliable operation and durability you
CONSUMERS WITH PACEMAKERS
As with any product that produces a vibrating motion
expect. This product has been inspected and tested
prior to shipment.
(optional), it is possible that some pacemakers may
interpret this motion as a false sense of movement
and/or exercise. This may or may not affect your pacemaker.
If you have any concerns, please consult your physician.
For information on disabling the vibrating motors, please
contact customer service by calling 1-800-979-1457.
USER-SERVICEABLE PARTS
This product is specifically designed require no user
maintenance. Therefore, you are encouraged not to open
any motors, alter the wiring, or adjust, modify or change
the structure of the product, as it will void the warranty.
POWER RATINGS:
MODEL NO: SY-66D
INPUT: AC 100V/110V - 50/60HZ, 1AMP
OUTPUT: DC 24V-3A
FUSE: 1A 250V (MAX 1.5A)
Customer Service: 1–800–979–1457
6
Safety Precautions
RADIO FREQUENCY IS 433.92 MHZ.
INTENDED USAGE
The electric adjustable bed should be installed with
FCC COMPLIANCE
the head board bracket and/or the head of the
This device complies with part 15 of the FCC
frame should be positioned close to a wall.
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
To comply with the FCC RF exposure compliance
requirements, no change to the antenna or
the device is permitted. Any change to the
antenna or the device could result in the device
exceeding the RF exposure requirements and
void user’s authority to operate the device.
PRODUCT RATINGS
The lift motors in your Ergo System are NOT designed for
continuous use. Reliable operation and full life expectancy
will be attained as long as the lift motors do not operate
more than two (2) minutes over an eighteen (18) minute
period, or approximately 10% duty cycle. Any attempt
to circumvent or exceed this rating will shorten the life
expectancy of this product and may void the warranty. The
recommended weight restrictions on our Ergo Systems are
as follows: Twin Long – 300 lbs., Split/Dual Queen – 300
lbs., Split/Dual CA King – 300 lbs. This Ergo System will
structurally support the recommended weight distributed
evenly across the head and foot sections. This product is
not designed to support or lift this amount of weight in
the head or foot sections alone.
NOTE: Exceeding the recommended weight
restrictions could damage your Ergo System and
void your warranty.
For best performance, you should enter and exit the Ergo
System while it is in the flat or fully lowered position.
Customer Service: 1–800–979–1457
7
GrandBed TEMPUR® Advanced Ergo System™
Commonly asked Questions and Answers
WHAT IS THE HEIGHT OF THE ERGO SYSTEM BASE?
With standard legs and casters installed, the overall
height is approximately 15 1/8” floor to the bottom
of the mattress. The distance between the floor and
the bottom edge of the base, with standard legs and
casters installed, is approximately 7 3/4”. See chart on
page 9 for other options.
IS IT POSSIBLE TO RAISE THE HEIGHT OF THE
ERGO SYSTEM BASE?
Yes, you can add up to 4” to the overall height of the
Ergo System by ordering the riser leg set. These include 6
replacement legs with casters, and come with either an
overall height of approximately 8” or 10”. Please note
that the riser leg set replaces the standard leg set that
comes with the Ergo System. They are not used together.
DOES THE ERGO SYSTEM BASE COME WITH
FOOTBOARD ATTACHMENTS?
No, you cannot attach a footboard directly to the Ergo
System base. However, you can use a “freestanding”
bed including headboard, footboard and side rails
by placing the complete Ergo System within the
assembled bed. It may be easiest to assemble the bed
around the Ergo System. You should measure the
inside dimensions of the assembled bed to be sure the
Ergo System will fit. One of our riser leg sets may be
required in some cases.
WILL THE ERGO SYSTEM FIT INSIDE EXISTING
FURNITURE?
The Ergo System is designed to fit into most
“freestanding” beds. We always recommend you
measure the inside dimensions of the assembled bed
to be sure the Ergo System will fit. Please refer to the
specifications on page 9 for exact dimensions of the base.
One of our riser leg sets may be required in some cases.
WHERE IS THE SERIAL NUMBER ON THE ERGO
SYSTEM BASE?
The serial number can be found on the law tag
attached to the cover, the power down box under
the base and on the frame right below the foot end
of the base. It may be easier to see by lifting the foot
slightly if possible. The serial number is also located on
a sticker on page 3 of the Complete Reference Guide
(owner’s manual) shipped with the base.
WHAT IS THE LIFT CAPACITY OF THE GRANDBED
TEMPUR® ADVANCED ERGO SYSTEM™?
Please see the chart below for Tempur-Pedic’s
recommended and approved “total people weight” limits
per the available mattress and Ergo Base combinations.
Total People Weight
Product
GrandBed
Dual Bases
900 lbs.
WHO DO I CALL FOR SERVICE OR SUPPORT IF NEEDED?
Service and technical support is available by calling
our dedicated customer service group at 1-800-9791457. An owner’s manual is included with each base
including other information for making claims.
IS AN EXTENDED WARRANTY AVAILABLE?
No.
DO I GET A FULL WARRANTY IF I PURCHASE A
FLOOR MODEL?
Yes. However, your warranty start date is the date of
manufacture which is clearly marked on the law tag
attached to the base (not your actual purchase date).
WHAT ARE THE ELECTRICAL REQUIREMENTS OF
THE ERGO SYSTEM BASE?
During normal operation, the base will typically draw
1.0 Amp of electricity from a normal AC wall outlet.
The power supply has a 1.5 Amp fuse installed to
prevent damage to the unit should a power surge
occur. It is highly recommended that the customer use
a power surge protector (not included with the base).
DOES THE UNIT HAVE AC OR DC MOTORS?
The lift motors used on the Ergo System base are DC
motors. The base’s power supply converts the AC
power from the wall outlet to DC power.
Customer Service: 1–800–979–1457
8
Single Base
Not Available
Q&A / Specifications
Bed Type
Specifications
A. Frame
width
B. Base
Width
Twin Long
33 1/2”
37 1/2”
Split Queen
26 1/4”
Split CA King
33 1/2”
C. Base
Length
Weight
79”
172 lbs.
29 1/2”
79”
136 lbs.
35 3/4”
82 3/4”
159 lbs.
39 3/8”
21 1/4”
6 5/8”
A
61”
C
B
7”
15 1/8”
27 3/16”
27 3/16”
54 3/8”
Measurements are approximate and based on standard leg with caster.
No Leg
(rest on frame)
Caster Only
Standard Leg Standard Leg
8” Riser Leg
8” Riser Leg
(without caster)
(without caster)
(with caster)
(with caster)
E D
E
E D
E D
E
E
(with caster)
F
F
F
F
F
(without caster)
F
F
F
10” Riser Leg 10” Riser Leg
E
D
D
E
D
D
D) To Frame
0”
2 1/2”
4 1/8”
6 5/8”
6”
8 5/8”
7 1/2”
10 1/8”
E) To Base
1”
3 7/8”
5 1/4”
7 3/4”
7 1/2”
10 1/8”
9 1/8”
11 5/8”
F) To Mattress
8 1/2”
11 1/8”
12 1/2”
15”
14 5/8”
17 1/4”
16 1/8”
18 3/4”
Customer Service: 1–800–979–1457
9
GrandBed TEMPUR® Advanced Ergo System™
Installation Instructions
A.
B.*
C.
D.
E.
F.
G.*
H.
I.*
J.
K.
L.
M.
N.
Before discarding any packing materials,
check your GrandBed TEMPUR Advanced
®
®
Ergo System™ carton and verify the following
items in the parts list are included:
PARTS LIST
*Attached
to base for
shipping
A. Wireless Remote Control (1) and
Four (4) AAA Batteries
B. Mattress Retainer Bar (1)*
C. Mattress Retainer Bar Cover (1)
D. Bed Leg with Caster (6)
E. Inner Headboard Bracket (2)
F. Outer Headboard Bracket (2)
G. Retainer Bar Bolt (4)*
H. Bracket Bolt (6)
I. Retainer Bar Plate (2)*
J. 5/16 Inch Washer (12)
K. 5/16 Inch Locking Nut (6)
L. Allen Wrench (1)
M.Wrench (1)
N. 9-Volt Batteries (2)
Customer Service: 1–800–979–1457
10
Installation
Pre-Delivery Procedure
PRIOR TO LOADING FOR DELIVERY:
STEP 1
Lift carton top off box to reveal the bottom of the base.
STEP 2
Using a power extension cord* to reach the base,
plug in the base’s power cord.
NOTE: If the base does not perform properly,
immediately call Tempur-Pedic Customer Service
at 800-979-1457. Be prepared to provide the
service agent with the serial number of the
base, the retailer’s name, and facts about
the situation.
NOTE: Do not uncoil the base power cord as
STEP 6
packaged for shipment.
Once the warehouse test is successful and complete:
*AN ELECTRICAL SURGE PROTECTION UNIT IS
RECOMMENDED (NOT INCLUDED).
• Unplug the power extension cord.
• Return the remote control to the accessory carton
(remove batteries).
STEP 3
Cut and remove power down box from frame and
install 9-Volt batteries.
• Place the lid back on the outer carton and secure
for delivery.
NOTE: Always keep the Ergo base in a flat,
not vertical, position during transportation
STEP 4
Remove the remote control and (4) AAA batteries from
and delivery. Always open the box in the flat
the accessory carton, open the battery door on the
position.
backside of the remote control, and install the batteries.
NOTE: To avoid damage to the Ergo System,
always open the carton while the bed is in the
STEP 5
flat position.
Power Test Procedure:
Press each of the following buttons long enough to
illuminate the red LED Signature Light on the remote
control, and watch/listen for the base to activate.
This ensures you will be delivering a base that is fully
functional. Test the base by pressing the buttons in
OPEN FLAT
the following sequence:
• Head Lift / Foot Lift / Head Massage / Foot Massage /
Stop / Flat
— Only press each long enough to see/hear each
motor activate.
Customer Service: 1–800–979–1457
11
GrandBed TEMPUR® Advanced Ergo System™
Delivery Procedure
STEP 12
Install headboard brackets if they are being used and
COMPLETING HOME DELIVERY:
adjust to allow a minimum of two inches clearance to
permit unobstructed movement.
STEP 7
Carefully take base in the carton to the bedroom and
place next to where the customer wants it set up.
STEP 8
Carefully lift your Ergo System out of the shipping
carton, keeping the unit top side down. For safety
NOTE: All tools necessary for installation are
included in the box.
reasons, this should be performed by two (2) people.
STEP 9
STEP 13
Reinstall batteries in remote control, uncoil base
Install mattress retainer bar at the foot of the base(s).
power cord, plug into power source, and perform
the Power Test Procedure to assure nothing was
damaged during trip.
STEP 13A
Slide the Retainer Bar Cover (C) onto the Retainer Bar
(B) so the screw holes are on top of the retainer bar.
STEP 10
Attach Ergo System Legs: Open the accessories box,
STEP 13B
take out the 6 legs, and thread them in a clockwise
Place the retainer bar plate on top of the retainer bar
direction into the pre-threaded holes in the frame.
cover, slide the screw through the plate and cover,
and screw into place. Before final tightening, ensure
NOTE: Hand tighten the legs securely to the
frame. DO NOT over tighten. Make sure the legs
are screwed completely into the frame. Legs that
are not securely attached may become unsafe.
DO NOT unscrew a leg to compensate for an
uneven floor.
NOTE: Your Ergo System is equipped with
special locking casters. In order to prevent the
movement of this product, all six casters should
be in the locked position.
retainer bar cover is pulled down completely over the
retainer bar.
STEP 14
Program remotes per instructions on Page 15.
STEP 15
STEP 11
Carefully flip the Ergo System over to the “topside up”
position.
Place the mattress(es) on the base(s).
NOTE: For more detailed instruction see the
NOTE: Make sure to lift Ergo System off ground
before flipping over. DO NOT use legs as a
leverage point to ensure they do not break.
Owner’s Guide. Be sure to give Owner’s Guide
and other materials to the new owner.
Customer Service: 1–800–979–1457
12
Installation
HEADBOARD INSTALLATION
NOTE: This step is only needed if using a headboard
Place the Bracket Bolt (H) with a 5/16 inch washer (J)
ONLY. Not headboard, footboard and side rails.
through the predrilled hole in the C-channel frame
NOTE: Failure to follow the proper headboard
and pass it through the Inner Headboard Bracket.
bracket installation instructions may result in
damage to your Ergo System.
WARNING: The bottom of the headboard cross member
must be positioned so that there is no more than 3
inches between the bottom of the headboard and the
top of the mattress. Failure to follow this instruction
could result in serious injury or death to a person or
pet caught between the mattress and the headboard.
Adding the 5/16 inch washer (J) and 5/16 inch nut
(K), hand tighten the bolt in place using the supplied
wrenches (L and M).
STEP 1
Assemble the Headboard Bracket:
STEP 1A
Use the wireless remote to raise the head of the bed
in order to gain access to the Ergo System frame.
Repeat for the other side of the frame.
STEP 1C
Place the open side of the Outer Headboard Bracket
(F) onto the exposed C-channel of the Inner
Headboard Bracket (E). This will create a tight fit
between (E) and (F).
STEP 1B
Place the Inner Headboard Bracket (E) into the
C-channel frame, making sure the bracket opening and
the C-channel opening are facing each other. This will
create a box shape. This step does not require you to
loosen or remove any bolts on the delivered bed frame.
Customer Service: 1–800–979–1457
13
GrandBed TEMPUR® Advanced Ergo System™
Place Bracket Bolts (H) with a 5/16 inch washer (J)
STEP 2B
through the Outer Headboard Bracket (F) and into
Measure the center-to-center distance of the
the Inner Headboard Bracket (E). Use 5/16 inch
mounting holes in the Headboard Bracket Assemblies.
washers (J) and 5/16 inch nuts (K) and hand tighten
to allow for adjustment.
STEP 2C
If the Headboard Brackets require adjustment, loosen
the bolts that are holding the Outer Headboard
Brackets and move them so that the mounting holes
on the Outer Headboard Bracket align with the
mounting holes on your headboard. Reinstall the
bolts on the Outer Headboard Bracket and firmly
tighten.
STEP 2D
Place your headboard bolts through the mounting
holes on both the Outer Headboard Bracket and your
headboard. Firmly tighten.
STEP 3
Place your Tempur-Pedic mattress on top of your Ergo
Repeat on the other side.
System Base.
STEP 1D
Ensure the Headboard Bracket is assembled with a
distance of 1.5 (38.1 mm) to 2 inches (50.8 mm)
between the edge of the Ergo System and the
headboard bracket assemblies.
WARNING: Verify the space between the
headboard cross member and the top of the
mattress is no more than 3 inches.
Your GrandBed TEMPUR® Advanced Ergo System™
STEP 2
Attach your headboard to the Headboard Brackets
installation is now complete. Refer to the Wireless Remote
following the steps below:
Control Guide on the following pages or the supplied
Quick Reference Guide for additional usage instructions.
STEP 2A
Measure the center-to-center distance of the
mounting holes in your headboard.
Customer Service: 1–800–979–1457
14
Operation
Wireless Remote Control Programming
ONE WIRELESS REMOTE CONTROL AND TWO ERGO BASES
NOTE: The use of “Base A” and “Base B” is for
STEP 5
description purposes only and the beds will not
Lightly press the learn button in Base B for three (3)
actually be labeled “Base A” or “Base B”.
seconds.
Learn Button
STEP 1
Place four (4) AAA batteries into the Wireless Remote
Control A.
STEP 6
When the Green LED light illuminates, press any
button on the wireless remote control.
NOTE: If a new signal is not received within 10
STEP 2
seconds, step 5 and step 6 must be repeated.
Store Wireless Remote Control B for future use.
NOTE: The green LED light will blink once it
receives a remote signal. The bed will not
STEP 3
Ensure the Ergo System bases are plugged into a
functioning outlet.
respond for 10 seconds during the remote
learn process.
STEP 7
STEP 4
Locate the Emergency Power Down Boxes under both
When the Green LED light on the Emergency Power
Base A and Base B. Install two (2) new 9-volt batteries.
Down Box turns off, you have completed the learning
process of the RF frequency code.
NOTE: The remote programming procedure may also
be performed using the learn button on the PLC.
NOTE: Base A is already programmed upon
delivery.
Base A
Base B
Customer Service: 1–800–979–1457
15
GrandBed TEMPUR® Advanced Ergo System™
Wireless Remote Control Features
READ ADVISORY INFORMATION IN THE SAFETY PRECAUTIONS SECTION OF THIS GUIDE CAREFULLY BEFORE
USING THIS PRODUCT. THE POTENTIAL FOR ELECTRIC SHOCK EXISTS IF ELECTRICAL COMPONENTS ARE NOT
INSTALLED OR OPERATED PROPERLY.
LED SIGNATURE LIGHT
A. RAISE (+) / LOWER (-)
HEAD SECTION OF THE BASE
B. RAISE (+) / LOWER (-)
FOOT SECTION OF THE BASE
C. RETURN ALL SECTIONS
TO THE FLAT POSITION
D. PROGRAM UP TO 4 MEMORY POSITIONS
F. INCREASE (+) / REDUCE (-)
MASSAGE INTENSITY ON
FOOT SECTION OF THE BASE
E. INCREASE (+) / REDUCE (-)
MASSAGE INTENSITY ON
HEAD SECTION OF THE BASE
G. STOP ALL MASSAGE FEATURES
H. SELECT 1 OF 4 MASSAGE
WAVE SPEEDS
Customer Service: 1–800–979–1457
16
Operation
Operating Instructions
HEAD AND FOOT ADJUSTMENTS (A, B)
Light illuminates and the Massage feature stops. The
• Adjusts the Head and Foot sections to the desired
Massage feature is designed to automatically shut off after
positions. Press until the red LED Signature Light
30 minutes of continuous use. The unit will reset after 5
illuminates and desired position is achieved.
minutes, and the Massage feature will again be available for
use.
BED “FLAT” BUTTON (C)
• To level the Ergo System to the Flat position,
press until the red LED Signature Light illuminates.
NOTE: The “FLAT” cycle can be interrupted and
cancelled by pressing the head or foot adjustment
buttons (A or B).
• You MUST stop Massage motors each time before
switching between wave speeds/types.
WAVE MASSAGE SPEED ADJUSTMENTS (H)
• If the Massage feature is off, press any Wave Speed
button to initiate the Wave Massage feature. Each button
represents the amount of time the massage spends in
MEMORY BUTTONS (D)
each section (head or foot) before switching. If the Wave
• Your GrandBed TEMPUR® Advanced Ergo System™ can
Massage feature is already on, you must first stop the
store up to four (4) Memory Positions.
• To Set a Memory Position: When in desired position,
press and hold Memory button until the LED Signature
Light flashes 3 times to signal Memory position is stored.
• To Recall a Memory Position: Press and hold the
massage by pressing the STOP button (G), and then press
the desired Wave Speed; otherwise the Wave Massage
feature will not start.
NOTE: If the massage motors are operating and
the “FLAT” button (C) is pressed, the massage
corresponding Memory button until the red LED
motors will stop operating during the lowering
Signature Light illuminates.* Do not hold for more than
of the Ergo System. To then resume massage
five (5) seconds, otherwise a new Memory position
operation, press the Head and/or Foot Massage
could be set. If the LED Signature Light begins to flash,
Adjustments (E, F) or select a Wave Speed.
you are reprogramming the Memory position.
HEAD AND FOOT MASSAGE ADJUSTMENTS (E, F)
ADDITIONAL WIRELESS REMOTE CONTROL FEATURES
• Turns on the Head and Foot Massage units
• To aid in the visibility of the Wireless Remote control in low
light environments, the buttons are backlit and will light up
(starting at intensity 1 of 10).
• Slowly increases or decreases Massage Intensity.
when a button is pressed.
To increase Massage Intensity, press the (+) button.
• You are able to control your Ergo System with the Wireless
To decrease Massage Intensity, press the (-) button.
Remote control without pointing the Wireless Remote
control directly at the receiver (best transmission range is
MASSAGE STOP (G)
• Press and hold STOP button until the red LED Signature
within 9 feet or 3 meters).
*NOTE: An unintentional touch to any button that does not illuminate the red LED Signature Light on the
wireless remote control will cause the keys to light up without performing the associated function. Press
the appropriate wireless remote control button until the red LED Signature Light illuminates to activate
the desired function. This feature was included to prevent any undesired movement should the wireless
remote control be dropped, etc.
Customer Service: 1–800–979–1457
17
GrandBed TEMPUR® Advanced Ergo System™
Troubleshooting
In the event that your GrandBed TEMPUR® Advanced Ergo System™ fails to operate properly, investigate the symptoms
and possible solutions provided in the chart below:
SYMPTOM
SOLUTION
Wireless remote control LED Signature Light illuminates
and appears to be operable but will not activate the
Ergo System.
• Verify that the power cord is plugged into a working,
grounded electrical outlet. A grounded, electrical
surge protection device is recommended. Test the
outlet by plugging in another working appliance.
• Verify the Red LED light on the PLC control box
is lit – if not the unit is not receiving power.
No features of the
GrandBed TEMPUR® Advanced Ergo System™
will activate.
• Program the wireless remote control (see the
Wireless Remote Control Guide, included with
this product, for programming procedures). Make
certain the Power Down Box is easily accessible.
Relocate the Power Down Box if necessary.
• Unplug the power cord, wait 45 seconds and plug
the power cord back in to reset the electronic
components.
• Your surge protection device and/or electrical circuit
breaker may be tripped. Check both to verify.
• Your surge protection device and/or electrical outlet
may be defective. Test the outlet by plugging in
another working appliance.
Wireless Remote Control LED Signature Light
will not illuminate.
• Replace the batteries in the Wireless Remote Control.
The unit requires four (4) AAA batteries.
• Ensure the batteries are installed correctly.
• The Ergo System may be obstructed. Elevate and
check for an obstruction. Remove the obstruction.
Head and/or Foot section will elevate but will
not return to the horizontal (flat) position.
• The head section may be too close to the wall.
• The headboard may be too close the edge of
the mattress. Verify that a 1.5” (38.1mm) to 2”
(50.8mm) distance is between the headboard
brackets and the mattress. Adjust if required.
Customer Service: 1–800–979–1457
18
Troubleshooting
SYMPTOM
SOLUTION
• Check batteries in Wireless Remote Control, replace
with four (4) new AAA batteries if necessary.
Head or Foot lift function has minor
interference during operation.
• Make sure that you are following the duty cycle
of the motors (do not operate more than two (2)
minutes over an eighteen (18) minute period, or
approximately 10% duty cycle).
• Press the lift buttons squarely & accurately.
• Wireless Remote Control may be experiencing
common Radio Frequency Interference from other
radio transmitting devices. Wait several seconds,
and then try pressing appropriate button again. See
FCC Compliance Statement on page 5 of this guide.
• If the bed is located on hard surface flooring, place
carpet pieces or rubber pieces (not included) under
each leg or caster of your Ergo System.
• Using the Wireless Remote Control, elevate the head
or foot section a short distance to realign the lift/
lower mechanisms with the bed support platform.
Excessive massage motor noise.
• Verify that your Ergo System is not positioned against
a wall, nightstand, or other object that may cause
the vibration or noise.
• If the Ergo System is installed over a bed frame, verify
that the massage motors are not causing the bed
frame (or bed frame components) to vibrate.
• Verify that the headboard attachment hardware is
properly tightened (if used).
A clicking noise is heard under the
bed when raising or lowering.
• This is normal. The lift motor relays “click” when
they are engaged. No action is required.
Massage motor overheats or stops.
• If the vibration motor overheats, the
thermoprotection will turn the motor off. Wait 15
minutes, turn the MASSAGE ON back on. If it does
not come on, turn it off and report the situation to
customer service.
Customer Service: 1–800–979–1457
19
GrandBed TEMPUR® Advanced Ergo System™
Emergency Power Down Cycle
NOTE: In the event that your Ergo System loses
STEP 2
power, there is an Emergency Power Down Box.
Press the large Red Button until the Red LED lights up
This box only functions if there is not power at
on the Emergency Power Down Box.
the PLC Control Box.
STEP 1
Place two (2) new 9-volt batteries into the Emergency
Power Down Box.
STEP 3
Continue to press the Red Button until the base fully
lowers to the flat position. Ensure hands and arms are
not in the path of moving parts.
NOTE: Lowering using this method is much
slower than the standard process.
FOR TECHNICAL SUPPORT OR SERVICE,
PLEASE CHOOSE FROM THE FOLLOWING NUMBERS:
QUESTIONS ABOUT YOUR ERGO SYSTEM BASE:
1-800-979-1457
QUESTIONS ABOUT YOUR TEMPUR-PEDIC MATTRESS
OR TO ORDER ERGO SYSTEM ACCESSORIES:
1-800-821-6621
OR VISIT WWW.TEMPURPEDIC.COM
20
Download PDF
Similar pages