Delonghi ESAM 04.350 S User Guide Manual

5713215081/09.10
0
BEAN TO CUP ESPRESSO AND
CAPPUCCINO MACHINE
DE
Instruction for use
GB
ESAM04.350
Electrical requirements
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you
are in any doubt about your supply contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure
outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children
might find it and plug it into a supply socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in use.
important: the wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth
green and yellow blue brown
earth
neutral
live
13 amp Fuse
Brown to live
Blue to
neutral
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or
by the earth symbol
or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains
lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified
electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should
only be replaced with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a
replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse
recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed
2
A
A6
A3 A4 A5
B
A7
A2
B1
B6
B3
B5
A1
A8
B4
B2
A19
A18
A9
A17
A20
A16
A21
A10
A15
A11
A22
A12
A14
A23
A13
C
C1
C2
C8
C3
C9
C4
C10
C5
C11
C6
C7
3
A24
1
2
3
4
5
6
8
9
10
11
12
13
14
15
4
7
M
A
X
16
20
7
24
28
17
18
19
22
23
25
26
27
29
30
31
21
5
Contents
HEATING WATER.................................................... 14
Electrical requirements.................................... 2
Preparation............................................................................. 14
Change the quantity of water delivered automatically. . ........ 14
INTRODUCTION....................................................... 7
CLEANING............................................................. 14
Symbols used in these instructions........................................... 7
Letters in brackets..................................................................... 7
Troubleshooting and repairs..................................................... 7
Cleaning the coffee maker...................................................... 14
Cleaning the coffee grounds container.................................... 15
Cleaning the drip tray............................................................. 15
Cleaning the inside of the machine......................................... 15
Cleaning the water tank.......................................................... 15
Cleaning the coffee spouts...................................................... 15
Cleaning the pre-ground coffee funnel................................... 15
Cleaning the infuser................................................................ 15
Cleaning the milk container.................................................... 16
Cleaning the hot water/steam nozzle..................................... 16
SAFETY................................................................... 7
Fundamental safety warnings.................................................. 7
DESIGNATED USE..................................................... 7
INSTRUCTIONS........................................................ 8
DESCRIPTION.......................................................... 8
DESCALING............................................................ 16
Description of the appliance..................................................... 8
Description of the milk container.............................................. 8
Description of control panel ..................................................... 8
SETTING WATER HARDNESS.................................... 17
Measuring water hardness...................................................... 17
Set water hardness................................................................. 17
The machine is now reprogrammed with the new water
hardness setting. . .................................................................. 17
PRELIMINARY CHECKS............................................. 9
Checking the appliance............................................................. 9
Installing the appliance............................................................ 9
Connecting the appliance......................................................... 9
Using the appliance for the first time........................................ 9
TECHNICAL SPECIFICATION..................................... 17
TURNING THE APPLIANCE ON................................... 9
disposal.............................................................. 17
TURNING THE APPLIANCE OFF................................ 10
DISPLAYED MESSAGES........................................... 18
MENU SETTINGS.................................................... 10
TROUBLESHOOTING............................................... 19
Descaling................................................................................ 10
Setting the language ............................................................. 10
Energy Saving......................................................................... 10
Adjust time............................................................................. 10
Auto-Start............................................................................... 10
Auto-Off (Stand-by)................................................................ 11
Setting the temperature......................................................... 11
Statistics function................................................................... 11
Default values (reset).............................................................. 11
MAKING COFFEE.................................................... 11
Selecting the coffee taste........................................................ 11
Selecting the quantity of coffee in the cup . ........................... 11
Customising the “my coffee” quantity..................................... 12
Adjusting the coffee mill......................................................... 12
Tips for a hotter coffee............................................................ 12
Making coffee using coffee beans........................................... 12
Making coffee using pre-ground coffee.................................. 12
MAKING DRINKS WITH MILK.................................. 13
Filling and attaching the milk container................................. 13
Making Cappuccino of Latte Macchiato................................... 13
Making frothed milk (without coffee)..................................... 13
Preparing milk (unfrothed and without coffee)...................... 13
Cleaning the milk frother with the CLEAN button . ................ 14
Programming the quantities of coffee and milk in the cup..... 14
6
INTRODUCTION
SAFETY
Thank you for choosing the ESAM04.350 automatic coffee
and cappuccino maker. We hope you enjoy using your new
appliance. Take a few minutes to read these instructions.
This will avoid all risks and damage to the machine.
Fundamental safety warnings
Symbols used in these instructions
Important warnings are identified by these symbols. These
warnings must absolutely be respected.
You should therefore respect the following safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
• Unplug directly from the plug only. Never pull the power
cable as you could damage it.
• To disconnect the appliance completely, place the main
switch at the back of the appliance in the 0 position (fig.
6).
• If the appliance is faulty, do not attempt to repair. Turn it
off, unplug from the mains socket and contact Customer
Services.
• If the plug or power cable is damaged, it must be replaced
by De’Longhi Customer Services only to avoid all risk.
Danger!
This is an electrical appliance and may cause electric shock.
Danger!
Failure to observe the warning could result in possibly life
threatening injury from electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Please note :
This symbol identifies important advice or information for the
user.
•
Letters in brackets
The letters in brackets refer to the legend in the Description of
the appliance on page 3.
•
Troubleshooting and repairs
In the event of problems, first try and resolve them following
the information given in the sections “Displayed messages” on
page 18 and “Troubleshooting” on page 19.
If this does not resolve the problem or you require further
information, you should consult Customer Services by calling
the number given on the annexed “Customer Service” sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee.
If repairs are required, contact De’Longhi Customer Services
only.
The addresses are given in the guarantee certificate provided
with the machine.
Important!
Keep all packaging (plastic bags, polystyrene foam) away
from children.
The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children must be supervised to ensure
they do not play with the appliance.
Danger of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
DESIGNATED USE
This appliance is designed and made to prepare coffee and heat
drinks.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from
improper use of the appliance.
This is a household appliance only.
It is not intended for use in:
• staff kitchen areas in shops, offices and other working
environments;
• farm houses;
7
•
•
DESCRIPTION
by clients in hotels, motels and other residential type
environments;
bed and breakfast type environments.
Description of the appliance
(page 3 - A )
A1. Grinding adjustment knob
A2. Main switch
A3. Beans container
A4. Beans container lid
A5. Cover for funnel and measure compartment
A6. Measure compartment
A7. Cup shelf (cup warmer active, when Energy Saving is
disabled)
A8. Pre-ground coffee funnel
A9. Hot water and steam nozzle
A10. Water tank
A11. Power cable
A12. Cup tray
A13. Drip tray
A14. Service door
A15. Grounds tray
A16. Coffee spout (adjustable height)
A17. Coffee guide
A18. Infuser
A19. Control panel
A20. Hot water spout
A21. Measure
A22. Cleaning brush
A23.Descaler
A24.Reactive strip to detect water hardness (Total hardness
test)
INSTRUCTIONS
Read these instructions carefully before using the appliance.
- Failure to respect these instructions may result in burns or
damage to the appliance.
The manufacturer is not liable for damage deriving from
failure to respect these instructions.
Please note:
Keep these instructions.
If the appliance is passed to other persons, they must also be
provided with these instructions.
Description of the milk container
(page 3 - B )
B1.Lid with milk frother
B2. Container handle
B3. CLEAN button
B4. Milk intake tube
B5. Frothed milk spout
B6. Milk container
Description of control panel
(page 3 - C )
A number of buttons on the panel have a dual function. This is
indicated in brackets in the description.
C1.Display: guides the user in using the appliance.
C2.
button: to deliver two cups of coffee (when
you access the MENU: to scroll backwards through the
menu)
C3.
button: to make 1 cup of coffee (when you access
the MENU: OK button to enable and confirm the selected
function)
8
s
n
s
d
C4.
C5.
C6.
C7.
C8.
C9.
C10.
C11.
MENU button: to access the settings menu.
button: to turn the appliance on and off (standby)
button to deliver hot water.
CAPPUCCINO button to deliver a cappuccino or
frothed milk (press button twice)
button: to select coffee quantity (when
you access the MENU: to scroll forwards through the
menu)
button: to select coffee taste (When you access
the MENU: ESC to exit the menu)
button: to perform a rinse cycle
button: to select pre-ground coffee
Using the appliance for the first time
•
•
Please note :
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee
in the grinder. The machine is, however, guaranteed to be
new.
You should customise water hardness as soon as possible
following the instructions in the section “Setting water
hardness” on page 17.
1. Plug the appliance into the mains socket and place the
main switch on the back of the appliance in the I position
(fig. 1).
You must first choose the language (the languages scroll
through at intervals of about 3 seconds).
2. When “English” appears, press the OK button (fig. 2). Once
the language has been saved, the message “ENGLISH set”
is displayed.
Follow the instructions indicated by the appliance:
3. “FILL TANK”: remove the water tank, fill to the MAX line
with fresh water then replace in the appliance (fig. 3).
4. “INSERT WATER SPOUT”: Check that the hot water spout
is inserted on the nozzle and place a container holding a
minimum of 100 ml underneath (fig. 4).
5. “Hot water Press OK”: press the OK button (fig. 2). “Please
wait” is displayed and the appliance begins to deliver
water from the hot water spout.
PRELIMINARY CHECKS
Checking the appliance
After removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact De’Longhi Customer Services.
Installing the appliance
Important!
When you install the appliance, you should respect the
following safety warnings:
• The appliance gives off heat. After positioning the
appliance on the worktop, leave a space of at least 3 cm
between the surfaces of the appliance and the side and
rear walls and at least 15 cm above the coffee maker.
• Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).
The appliance ends the first start up procedure, then the
message “Turning off Please wait” is displayed and the
appliance goes off.
The coffee maker is now ready for normal use.
•
Connecting the appliance
Please note:
When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before the
appliance starts to give satisfactory results.
TURNING THE APPLIANCE ON
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Please note:
Before turning the appliance on, make sure the main switch on
the back of the appliance is in the I position (fig. 1).
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
The appliance is ready for use only after completion of this
cycle.
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
9
4. Press the or button until the required language is
displayed;
5. Press the OK button to confirm;
6. Press the ESC button exit the menu.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath. Avoid contact with
splashes of water.
• To turn the appliance on, press the
button (fig. 5).
The message “Heating up Please wait” is displayed.
After heating, the message “Rinsing” is displayed, together with
a progress bar which gradually fills as preparation progresses.
As well as heating the boiler, the appliance also heats the
internal circuits by circulating hot water.
The appliance is at temperature when the message indicating
the taste and quantity of coffee appears.
Energy Saving
Use this function to enable or disable “Energy saving” mode.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To enable or disable the function, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Energy saving” is displayed;
3. Press the OK button. “Disable?” is displayed (or “Enable?”
if the function has already been disabled).
4. Press the OK button to disable or enable the function or
the ESC button to exit the menu.
When the function is active, if the machine is not used for
about 1 minute, “Energy saving” is displayed.
TURNING THE APPLIANCE OFF
Each time the appliance is turned off, it performs an automatic
rinse cycle which cannot be interrupted.
Important!
To avoid damaging the appliance, always press the
button to turn off.
•
Please note!
To exit “Energy saving” mode, press any button, then press
the button corresponding to the drink you want to make.
A few seconds may elapse between “Energy saving” mode
and delivery of the first drink; “Preparation underway...” is
displayed.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts
(only if coffee has been made).
Avoid contact with splashes of water.
•
To turn the appliance off, press the button
appliance performs a rinse cycle then goes off.
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Adjust time” is displayed;
3. Press the OK button. The hours flash on the display;
4. Press the or button to change the hours;
5. Press the OK button to confirm. The minutes flash on the
display;
6. Press the or button to change the minutes;
7. Press the OK button to confirm;
8. Press the ESC button to exit the settings menu.
(fig. 5). The
Please note:
If the appliance is not used for an extended period, place the
main switch in the 0 position (fig. 6).
Never place the main switch in the 0 position while the
appliance is on.
No rinse is performed if no drinks with coffee have been made
while the machine has been on.
MENU SETTINGS
When you access the settings menu by pressing the MENU button, the
following menu items can be selected: Descale, Set language, Energy
saving, Adjust time, Auto-start, Auto-off, Set temperature, Water
hardness, Statistics, Default values.
Please note!
The time is displayed when the appliance is in stand-by or
energy saving mode. If the time has not been adjusted, “0:00”
flashes on the display.
Descaling
For instructions on descaling, see page 16.
Auto-Start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Setting the language
To modify the language of the display, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Set language” is displayed;
3. Press the OK button;
Please note!
To enable this function, the time must be set correctly.
To enabled Auto-on, proceed as follows:
10
”
r
r
s
”
n
Press the MENU button to enter the settings menu.
Press the or button until “Auto-start” is displayed;
Press the OK button. “Enable?” is displayed;
Press the OK button. The hours flash on the display;
Press the or button to select the hours;
Press the OK button to confirm. The minutes flash on the
display;
7. Press the or button to change the minutes;
8. Press the OK button to confirm. The
symbol appears
under “Auto-start” on the display.
9. Press the ESC button to exit the menu. When the appliance
is in stand-by, the
symbol appears next to the clock
to indicate that auto-start has been programmed.
To disable the function:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Auto-start” is displayed;
3. Press the OK button. “Disable?” is displayed;
4. Press the OK button to confirm;
5. Press the ESC button to exit the menu. When the appliance
is in stand-by, the
symbol is no longer displayed.
Statistics function
This displays statistics relating to the machine.
To display, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Statistics” is displayed;
3. Press the OK button;
4. By pressing the or button, you can check:
- how many coffees have been made;
- how many cappuccinos have been made;
- how many times the machine has been descaled;
- the total number of litres of water delivered.
5. Press the ESC button twice to exit the menu.
1. 2. 3. 4.
5.
6. Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language which
remains as set). To reset all settings, proceed as follows:
1. Press the MENU button to enter the menu;
2. Press the or button until “Default values” is
displayed;
3. Press the OK button;
4. The message “Confirm?” is now displayed;
5. Press the OK button to confirm and exit.
Auto-Off (Stand-by)
The appliance is set by default to go off if not used for two
hours.
The time can be changed so that the appliance switches off
after 15 or 30 minutes, or after 1, 2 or 3 hours.
To re-programme Auto-off, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Auto-off” is displayed;
3. Press the OK button;
4. Press the or button until the required time (15 or 30
minutes, or 1, 2 or 3 hours) is displayed;
5. Press the OK button to confirm;
6. Press the ESC button exit the menu.
Auto-off is programmed.
MAKING COFFEE
Please note!
A few seconds may elapse between energy saving mode and
delivery of the first coffee.
Selecting the coffee taste
The appliance is set by default to make coffee with a standard
taste.
You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
Setting the temperature
To modify the temperature of the water used to make the
coffee, proceed as follows:
1. Press the MENU button to enter the settings menu.
2. Press the or button until “Set temperature” is
displayed;
3. Press the OK button;
4. Press the or button until the required temperature is
displayed (l = low; llll = high);
5. Press the OK button to confirm;
6. Press the ESC button exit the menu.
To change the taste, press the
button (fig. 7)
repeatedly until the required taste is displayed.
Selecting the quantity of coffee in the cup
The appliance is set by default to make a standard quantity of
coffee.
To select the quantity of coffee, press the
button (fig.
8) repeatedly until the message corresponding to the required
quantity of coffee is displayed:
Setting water hardness
For instructions on setting water hardness, see page 17.
11
Corresponding coffee
MY COFFEE
espresso (ml)
program.
from ≃20 to ≃180
SHORT
≃40
STANDARD
≃60
LONG
≃90
EXTRA LONG
≃120
•
•
•
Hot water is delivered from the spout, heating the internal
circuits of the appliance and thus raising the coffee
temperature.
place the cups on the cup warmer until they are warm.
warm the cups by rinsing them with hot water (using the
hot water function).
set the “high” coffee temperature (llll) in the
menu.
Making coffee using coffee beans
Customising the “my coffee” quantity
The appliance is set by default to automatically deliver 30 ml of
“MY COFFEE”. To modify these settings, proceed as follows:
1. Place a cup under the coffee spouts ( fig. 9).
2. Press the
(button repeatedly (fig. 8) until “MY
COFFEE” is displayed.
3. Keep the button (fig. 2) pressed until the message
“Program Quantity” is displayed. Release the button. The
machine starts making the coffee;
4.As soon as the coffee in the cup reaches the required level,
press the
button again.
The quantity set has now been programmed.
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
1. Fill the container with coffee beans (fig. 11).
2. Place under the coffee spouts:
- 1 cup, if you want to make 1 coffee (fig. 9);
- 2 cups, if you want 2 coffees (fig. 12);
3.Lower the spouts as near as possible to the cup. This makes
a creamier coffee (fig. 13).
4. Press the button corresponding to the number of coffees
required (1 cup
or 2 cups
) (fig. 2 and 14).
5. Preparation begins. The quantity of coffee is displayed
together with a progress bar which gradually fills as
preparation progresses.
Once the coffee has been made, the appliance prepares for use
again.
Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that
delivery is either too fast or too slow (a drop at a time), this
can be corrected by adjusting the grinding adjustment knob
(fig. 10).
Please note:
While the machine is making coffee, delivery can be
interrupted at any moment by pressing one of the coffee
buttons (
or
).
• At the end of delivery, to increase the quantity of coffee
in the cup, just press (within 3 seconds) one of the coffee
buttons (
or
).
Once the coffee has been made, the appliance is ready to use
again.
•
Please note!
The grinding adjustment knob must only be turned when the
coffee mill is in operation.
For faster delivery (not a drop at
a time), turn one click clockwise
towards “7” (coarser ground coffee).
For fuller bodied creamier coffee,
turn one click anticlockwise towards
“1” (finer ground coffee).
These adjustments will only be
evident after at least 2 cups of coffee have been delivered.
If delivery is still too fast or too slow, repeat the correction,
turning the knob another click.
Important!
If the coffee is delivered a drop at a time, too fast and not creamy
enough or too cold, read the tips in the “Troubleshooting”
section on page 19.
Various alarm messages could be displayed while using the
machine. Their meaning is explained in the section “Displayed
messages” (page 18).
Tips for a hotter coffee
For a hotter coffee, you are recommended to:
• before delivering the coffee, perform a rinsing cycle by
pressing the
button to select the “Rinsing” function.
Making coffee using pre-ground coffee
•
12
Important!
Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
e
s
e
•
it. This could damage the appliance.
Never use more than one level
measure or it could dirty the inside
of the machine or block the funnel.
During this time, “Preparation underway...” is displayed.
Please note!
If you use pre-ground coffee, you can only make one cup of
coffee at a time.
1. Press the
(C11) button: “Pre-ground” flashes on
the display.
2. Put one level measure of pre-ground coffee into the
funnel (fig. 14).
3. Place a cup under the coffee spouts (fig. 9).
4. Press the
delivery button (fig. 2).
5. Preparation begins. A bar appears on the display and
gradually fills as preparation progresses.
Once the coffee has been made, the appliance prepares for
use again.To disable the pre-ground coffee function, press the
or
button again.
Please note!
To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid and hot water nozzle as
described in the section “Cleaning the milk container” and
“Cleaning the hot water/steam nozzle” (page 16).
e
e
•
t
y
Making Cappuccino of Latte Macchiato
1.Attach the milk container (see previous section) and place
a sufficiently large cup under the coffee spouts and milk
spout.
2. Place the frothed milk regulator between “CAPPUCCINO”
and “CAFFELATTE” (fig. 21).
3. Press the CAPPUCCINO button (fig. 22). “CAPPUCCINO”
is displayed, together with a progress bar which fills
gradually as preparation proceeds.
4.After a few seconds, frothed milk flows out of the milk
spout into the cup below. If the froth is not satisfactory,
move the milk regulator towards “CAPPUCCINO” (= +
froth) or towards “CAFFELATTE” (= - froth). Milk delivery
stops automatically and coffee delivery begins.
5. The cappuccino is ready. Sweeten to taste and, if desired,
sprinkle the froth with a little cocoa powder.
MAKING DRINKS WITH MILK
Filling and attaching the milk container
1.Remove the lid (fig. 16);
2. Fill the milk container with a sufficient quantity of milk,
not exceeding the MAX level marked on the handle (fig.
17).
y
”
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (fig. 18).
4. Place the lid back on the milk container.
5.Remove the hot water spout from the nozzle (fig. 19).
6.Attach the container to the nozzle, pushing as far as it will
go (fig. 20).
7. Follow the instructions for each function.
Please note!
If you want to interrupt preparation during delivery, press
the CAPPUCCINO button.
• At the end of delivery, to increase the quantity of coffee
in the cup, just press (within 3 seconds) the CAPPUCCINO
button.
•Do not leave the milk container out of the refrigerator for
longer than strictly necessary. The warmer the milk (5°C
ideal), the poorer the froth will be.
•
Please note!
For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
The quality of froth can be adjusted during delivery
by moving the regulator slightly towards the word
CAFFELATTE for less froth.
Moving it towards the word CAPPUCCINO obtains a
more froth.
Making frothed milk (without coffee)
To make frothed milk, proceed as described in the previous
section, placing the milk froth regulator in the CAPPUCCINO
position and pressing the CAPPUCCINO button twice
consecutively (within two seconds) (fig. 22).
The appliance displays “Frothed milk” .
Please note!
If during delivery you want to stop making milk or coffee, press
the CAPPUCCINO button once.
- froth
Preparing milk (unfrothed and without coffee)
Proceed as described in the previous section, placing the milk
froth regulator in the CAFFELATTE position.
+ froth
•
If “Energy Saving” mode is enabled, you may have to wait
a few seconds before the first cappuccino is delivered.
13
Cleaning the milk frother with the CLEAN button
HEATING WATER
Important! Danger di scottature
When cleaning the internal tubes of the milk container, a little
hot water leaks out of the frothed milk tube (B5).
Avoid contact with splashes of water.
“Press CLEAN button” flashes on the display each time you
use a milk function. To eliminate all milk residues, proceed as
follows:
1.Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Press the “CLEAN” button (fig. 23) and keep pressing until
the progress bar which appears on the display together
with the message “Cleaning underway” is complete;
4.Remove the milk container and always clean the nozzle
with a sponge (fig. 24).
Please note:
A few seconds may elapse between “Energy saving” mode and
delivery of hot water; “Preparation underway...” is displayed.
•
•
•
Preparation
Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water.
The hot water spout becomes hot while water is being delivered
and must be handled by the handle only.
1. Make sure the hot water spout is attached correctly
2. Place a container under the water spout (as close as
possible to avoid splashes) (fig. 4).
3. Press the
button The message “Hot Water” is
displayed.
4. Water flows out of the spout. Delivery stops automatically
after about 250 ml.
5. To interrupt delivery of hot water manually, press the
button again.
Please note!
When “Press CLEAN button” flashes on the display, you
can still prepare any type of coffee or milk. If you have to
make a number of drinks with milk, wait until you have
delivered the last cup before cleaning the container.
The milk left in the container can be kept in the
refrigerator.
In some cases, to clean you must wait for the appliance to
heat up, holding the CLEAN button down.
Change the quantity of water delivered automatically.
The appliance is set by default to automatically deliver 250ml.
To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press the
button until the message “Hot Water
Program Quantity” is displayed.
3. When the hot water in the cup reaches the required level,
press the
button again.
The machine is now reprogrammed with the new quantity.
Programming the quantities of coffee and milk in the
cup
The appliance is set by default to automatically deliver standard
quantities.
To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk spout.
2. Press the CAPPUCCINO button and hold down for at
least 8 seconds until the message “Milk for CAPPUCCINO
Program Quantity” is displayed.
3. Release the button. The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the CAPPUCCINO button again.
5. After a few seconds, the appliance starts delivering coffee
into the cup and the message “Coffee f. CAPPUCCINO
Program Quantity” is displayed.
6. Once the required quantity of coffee has been delivered
into the cup, press the CAPPUCCINO button. Coffee
delivery stops.
The machine is now reprogrammed with the new quantities.
CLEANING
•
•
•
Important!
Do not use solvents, abrasive detergents or alcohol to
clean the appliance. With De’Longhi superautomatic
coffee makers, you need not use chemical products to
clean the machine.
None of the components can be washed in a dishwasher
apart from the milk container (B).
Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
Cleaning the coffee maker
The following parts of the machine must be cleaned regularly:
- coffee grounds container (A15),
- drip tray (A13),
- the inside of the machine, accessible after opening the
service door (A14),
14
d
t
r
,
c
e
e
-
-
-
-
-
water tank (A10),
coffee spouts (A16) and hot water nozzle (A9),
pre-ground coffee funnel (A7),
infuser (A18)
milk container (B).
Never immerse the coffee maker in water.
1. Check regularly (about every 100 coffees) that the inside
of the appliance (accessible after removing the drip tray)
is not dirty. If necessary, remove coffee deposits with the
brush supplied.
2.Remove the residues with a vacuum cleaner (fig. 28).
Cleaning the coffee grounds container
When “EMPTY GROUNDS CONTAINER” is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coffee cannot be made.
1.Open the service door on the front of the appliance (fig.
25), extract the drip tray (fig. 26), empty and clean.
2.Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
with the spatula on the brush provided.
3.Replace the drip tray complete with grounds container.
4. Close the service door.
Cleaning the water tank
1. Clean the water tank (A10) regularly (about once a month)
with a damp cloth and a little mild washing up liquid.
2. Clean to remove all washing up liquid residues, then rinse
the water tank thoroughly.
3. Fill the tank with fresh water and put back in the
appliance.
Cleaning the coffee spouts
1. Clean the coffee spouts with a sponge or cloth (fig. 29).
2. Check the holes in the coffee spout are not blocked. If
necessary, remove coffee deposits with a toothpick (fig.
30).
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds. If this is not done,
when you make the next coffees, the grounds container may
fill up more than expected and clog the machine.
Cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the pre-ground
coffee funnel (A7) is not blocked. If necessary, remove coffee
deposits with the brush (A22) supplied.
Cleaning the drip tray
Important!
If the drip tray is not emptied regularly, the water could overflow
from the edge and seep inside or around the machine.
This could damage the machine, the surface it rests on or the
surrounding area.
Cleaning the infuser
The infuser (A18) must be cleaned at least once a month.
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 26).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned.
To remove the drip tray:
1.Open the service door (fig. 25);
2.Remove the drip tray and the grounds container (fig. 26);
3.Empty the drip tray and grounds container and wash
them;
4.Replace the drip tray complete with grounds container;
5. Close the service door.
1. Make sure the machine is correctly turned off (see “Turning
off”, page 10).
2.Open the service door (fig. 24).
3.Extract the drip tray and the grounds container (fig. 26).
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (fig. 31).
Important!
The infuser may not be extracted when the machine is on.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID - NO DISH WASHER
Do not use washing up liquid to clean the infuser as it could
cause damage.
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
6. Use the brush (A22) to remove any coffee residues left in
the infuser housing, visible through the infuser door.
7.After cleaning, replace the infuser by sliding it onto the
internal support and pin at the bottom, then push the
Cleaning the inside of the machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned
off (see “Turning off”, page 10) and unplugged from the mains
power supply.
15
Cleaning the hot water/steam nozzle
Each time you prepare milk, clean the nozzle with a sponge to
remove milk residues from the gaskets (fig. 24).
PUSH symbol fully in until it clicks into place.
DESCALING
Descale the machine when the message “DESCALE” flashes on
the display.
Important!
Descaler contains acids which may irritate the skin and eyes.
It is vital to respect the manufacturer’s safety warnings given on
the descaler pack and the warnings relating to the procedure to
follow in the event of contact with the skin and eyes.
Please note!
If the infuser is difficult to insert,
you must first adapt it to the right
dimensions by pressing it
forcefully from the bottom and
top as shown in the figure.
8. Once inserted, make sure the two red buttons have
snapped out.
9.Replace the drip tray and waste coffee
container.
10. Close the service door.
Please note!
Use De’Longhi descaler only. Under no circumstances should
you use sulphamic or acetic based descalers. Their use
invalidates the guarantee.
Failure to descale the appliance as described above also
invalidates the guarantee.
1. Turn the machine on.
2. Press the MENU button to enter the settings menu. Press
the or button until “Descale” is displayed;
3. Press the OK button to confirm: The message “Add descaler
Press OK” is displayed.
4. Before confirming empty the water tank (A10) completely.
Pour the descaler (A23) diluted with water (respecting the
proportions indicated on the descaler pack) into the water
tank and replace the tank in the appliance.
Cleaning the milk container
Clean the milk container each time you prepare milk as
described below:
1. Remove the lid of the
milk container.
2. Remove the milk
spout and intake
tube.
3. Wash
all
the
components
thoroughly
with
hot water and mild
washing-up liquid.
All components are
dishwasher safe,
placing them in the
top basket of the
dishwasher.
4. Make sure there are
no milk residues left
inside the holes.
5. Check that the intake
tube and spout are not clogged with milk residues.
6.Replace the milk spout and intake tube.
7.Replace the milk container lid.
Important! Danger of burns
Hot water containing acid flows out of the hot water spout.
Avoid contact with splashes of water.
5. Place an empty container with a minimum capacity of 1.5
litres under the hot water spout.
6. Confirm with the OK button.
7. After confirming by pressing OK, the message “Descale
underway” is displayed. The descale programme starts
and the descaler liquid comes out of the water spout.
The descale programme automatically performs a series
of rinses and pauses to remove limescale deposits from
inside the machine.
After about 30 minutes, the message “Rinsing FILL TANK” is
displayed.
8. The appliance is now ready for rinsing through with
clean water. Remove the water tank, empty, rinse under
running water, fill with clean water and replace. “Rinsing
Press OK” is displayed.
9.Empty the container used to collect the descaler solution
and replace it under the cappuccino maker.
16
o
e
s
.
e
r
e
s
.
s
r
g
TECHNICAL SPECIFICATION
10. Press the OK button to start rinsing. Hot water flows out
of the spout and the message “Rinsing Please wait” is
displayed.
11. When the water tank is completely empty, the message
“Rinsing complete Press OK” is displayed.
12. Press the OK button. The appliance goes off
automatically.
To turn the appliance on again, press the
button.
Voltage:
220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1350W
Pressure: 15 bar
Water tank capacity: 1,8 L
Size: LxHxD: 282x364x425 mm
Cable length:
1,5 m
Weight: 11 Kg
Max. beans container capacity:
200 g
SETTING WATER HARDNESS
The appliance complies with the following EC directives:
The DESCALE message is displayed after a period of time
established according to water hardness.
The machine is set by default for a hardness value of 4.
The machine can also be programmed according to the actual
hardness of the mains water in the various regions, varying the
frequency with which the message is displayed.
•
•
•
•
Measuring water hardness
1.Remove the “TOTAL HARDNESS TEST” (A24) indicator
paper from its pack.
2.Immerse the paper completely in a glass of water for one
second.
3.After about a minute, 1, 2, 3, or 4 red squares form,
depending on the hardness of the water. Each square
corresponds to one level.
Level 1
lmmm
Level 2
llmm
Level 3
lllm
Level 4
llll
Stand-by Directive no. 1275/2008
Low Voltage Directive 2006/95/EC and subsequent
amendments;
EMC Directive 2004/108/EC and subsequent
amendments
Materials and accessories coming into contact with food
conform to the provisions of EC regulation 1935/2004.
disposal
Important information for correct disposal of the
product in accordance with EC Directive 2002/96/EC.
At the end of its working life, the product must not
be disposed of as urban waste.
It must be taken to a special local authority differentiated
waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids
possible negative consequences for the environment and
health deriving from inappropriate disposal and enables the
constituent materials to be recovered to obtain significant
savings in energy and resources.
As a reminder of the need to dispose of household appliances
separately, the product is marked with a rubbish bin bearing
a cross.
Set water hardness
1. Press the MENU button to enter the settings menu.
2. Press the or button and select “Water hardness”.
3. Confirm the selection by pressing the OK button.
4. Press or to set the water hardness identified using the
indicator paper (see figure in the previous section).
5. Press the OK button to confirm the setting.
6. Press the ESC button to exit the menu.
The machine is now reprogrammed with the new water
hardness setting.
17
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
REMEDY
FILL TANK
Insufficient water in the tank.
Fill the tank with water and/or insert it correctly, pushing it
as far as it will go until it clicks into place (fig. 3).
GROUND TOO FINE ADJUST
MILL
The grinding is too fine and the coffee is delivered too
slowly or not at all.
Repeat coffee delivery and turn the grinding adjustment
knob one click clockwise towards “7” while the coffee mill
is in operation.
If after making at least 2 coffees delivery is still too slow,
repeat the correction procedure, turning the Grinding
adjustment knob another click until delivery is correct.
INSERT WATER SPOUT
The water spout is not inserted or is inserted incorrectly.
Insert water spout as far as it will go (fig. 4).
EMPTY GROUNDS CONTAINER
The grounds container is full.
Empty the grounds container and clean, then replace.
Important: when removing the drip tray, the grounds
container MUST be emptied, even if it contains few
grounds. If this is not done, when you make the next
coffees, the grounds container may fill up more than
expected and clog the machine. (To ensure the 72 hours are
calculated correctly, the appliance must never be turned off
with the main switch in the 0 position.)
72 hours have passed since the first coffee after the
grounds container was last emptied.
INSERT GROUNDS CONTAINER
After cleaning, the grounds container has not been
replaced.
Open the service door, remove the drip tray and insert the
grounds container.
ADD PRE-GROUND COFFEE
The “pre-ground coffee” function has been selected
without placing any pre-ground coffee in the funnel.
Place pre-ground coffee in the funnel or deselect the
“pre-ground” function.
DESCALE
The machine must be descaled.
The descaling procedure described in the “Descaling”
section needs to be performed as soon as possible.
LESS COFFEE
Too much coffee has been used.
Select a milder taste or reduce the quantity of pre-ground
coffee.
FILL BEANS CONTAINER
The coffee beans have run out.
Fill the beans container
The pre-ground coffee funnel is clogged.
Empty the funnel as described in the section “Cleaning the
pre-ground coffee funnel”.
INSERT INFUSER ASSEMBLY
The infuser has not been replaced after cleaning.
Insert the infuser as described in the paragraph “Cleaning
the infuser”.
CLOSE DOOR
The service door is open
Close the service door.
INSERT MILK CONTAINER
The milk container is not inserted correctly.
Insert the milk container as far as it will go.
PRESS CLEAN
Milk has been delivered recently and the tubes inside the
milk container must be cleaned.
Press the “CLEAN” button and keep pressing until the
progress bar is complete. “Cleaning underway” is displayed.
Energy Saving
The function is active and reduces electricity consumption.
Disable the function from the menu (See section “Energy
Saving”).
GENERAL ALARM
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly, as described
in the section “Cleaning and maintenance”. If the message
is still displayed after cleaning, contact a service centre.
EMPTY CIRCUIT FILL CIRCUIT
alternating with...
Hot water Press OK
The water circuit is emtpy
Press OK button to deliver water from the spout until it
flows out normally.
18
TROUBLESHOOTING
Below is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact Customer Services.
PROBLEM
POSSIBLE CAUSE
REMEDY
The coffee is not hot
The cups were not preheated.
Warm the cups by rinsing them with hot water (using the
hot water function).
The infuser has cooled down because 2/3 minutes have
elapsed since the last coffee was made.
Before making the coffee, heat the infuser using the rinse
button.
A low coffee temperature is set.
Set maximum coffee temperature in the menu (llll).
The coffee is ground too coarsely.
Turn the grinding adjustment knob one click anticlockwise
towards “1” while the coffee mill is in operation (fig.
8). Continue one click at a time until coffee delivery is
satisfactory. The effect is only visible after delivering 2
coffees (see the section: “Adjusting the coffee mill” on
page 12).
Wrong type of coffee
Use a type of coffee for espresso coffee makers.
The coffee is delivered too
slowly or a drop at a time.
The coffee is ground too finely.
Turn the grinding adjustment knob one click clockwise
towards “7” while the coffee mill is in operation (fig. 11).
Continue one click at a time until coffee delivery is
satisfactory. The effect is only visible after delivering 2
coffees (see the section: “Adjusting the coffee mill” on
page 12).
The coffee does not come out
of the spouts, but from around
the service door.
The holes in the spouts are clogged.
Clean the spouts with a toothpick (fig. 29).
The coffee guide inside the service door is blocked.
Thoroughly clean the coffee guide, particularly near the
hinges.
The milk contains bubbles or
squirts out of the milk spout.
The milk is not cold enough or is not semi-skimmed.
You should ideally use skimmed or semi-skimmed milk at
refrigerator temperature (about 5°C).
If the result is not as you wished, try changing brand
of milk.
The milk container lid is dirty.
Clean the milk container lid as described in the section
“Cleaning the milk container” (page 16).
The hot water/steam nozzle is dirty
Clean the nozzle as described in the section “Cleaning the
hot water/steam nozzle” (page 16).
The milk container lid is dirty.
Clean the milk container lid as described in the section
“Cleaning the milk container” (page 16).
The hot water/steam nozzle is dirty
Clean the nozzle as described in the section “Cleaning the
hot water/steam nozzle” (page 16).
the frothed milk regulator is in the "CAFFELATTE" position.
Put the milk regulator in the “CAPPUCCINO” position.
The appliance does not come
on.
It is not plugged into the mains socket.
Plug into the mains socket.
The main switch is not in position I.
Place the main switch in the I position (fig. 1).
The milk does not come out of
the milk spout.
The milk container lid is dirty.
Clean the milk container lid as described in the section
“Cleaning the milk container” (page 16).
“Energy Saving” mode is
enabled, but the cup warmer
is hot
A number of drinks have been prepared in rapid succession.
The coffee is not creamy
enough.
The milk is not frothed.
19
Download PDF
Similar pages