Contents
MAKING DRINKS WITH MILK.................................. 14
Filling and attaching the milk container................................. 14
Making caffelatte.................................................................... 14
Making cappuccino................................................................. 15
Making macchiato . ................................................................ 15
Making milk............................................................................ 15
Cleaning the milk container after use..................................... 15
Programming the quantities of coffee and milk in the cup..... 15
INTRODUCTION....................................................... 8
Symbols used in these instructions........................................... 8
Letters in brackets..................................................................... 8
Troubleshooting and repairs..................................................... 8
SAFETY................................................................... 8
Fundamental safety warnings.................................................. 8
PREPARING HOT WATER OR STEAM......................... 16
DESIGNATED USE..................................................... 8
Delivering hot water .............................................................. 16
Steam delivery........................................................................ 16
Tips for using steam to froth milk............................................ 16
Cleaning the spout after use................................................... 16
INSTRUCTIONS........................................................ 8
DESCRIPTION.......................................................... 9
Description of the appliance . ................................................... 9
Description of milk container.................................................... 9
Description of the accessories................................................... 9
Description of control panel (touch screen)............................... 9
CLEANING............................................................. 16
Cleaning the coffee maker...................................................... 16
Cleaning the coffee grounds container.................................... 17
Cleaning the drip tray............................................................. 17
Cleaning the inside of the machine......................................... 17
Cleaning the water tank.......................................................... 17
Cleaning the coffee spouts...................................................... 17
Cleaning the pre-ground coffee funnel................................... 17
Cleaning the infuser................................................................ 17
Cleaning the milk container.................................................... 18
PRELIMINARY CHECKS............................................. 9
Checking the appliance............................................................. 9
Installing the appliance............................................................ 9
Connecting the appliance....................................................... 10
Using the coffee maker for the first time................................. 10
TURNING THE APPLIANCE ON ................................. 10
DESCALING............................................................ 18
TURNING THE APPLIANCE OFF................................ 10
SETTING WATER HARDNESS.................................... 19
MENU SETTINGS.................................................... 10
Measuring water hardness...................................................... 19
Set water hardness................................................................. 19
Rinsing.................................................................................... 11
Setting the language.............................................................. 11
Energy Saving......................................................................... 11
Adjust time............................................................................. 11
Auto-start............................................................................... 11
Auto-off (Stand by)................................................................. 11
Coffee temperature................................................................. 12
Install filter............................................................................. 12
Beep....................................................................................... 12
Statistics function................................................................... 12
Default values (reset).............................................................. 12
WATER SOFTENER FILTER (if fitted)..................... 19
Installing the filter ................................................................. 19
Replacing the filter . ............................................................... 19
TECHNICAL SPECIFICATION..................................... 20
DISPOSAL.............................................................. 20
DISPLAYED MESSAGES........................................... 20
TROUBLESHOOTING............................................... 21
MAKING COFFEE.................................................... 12
Selecting the coffee taste........................................................ 12
Selecting the quantity of coffee in the cup.............................. 12
Customising the espresso “my coffee” quantity....................... 12
Programming the long “my coffee” quantity........................... 13
Regulating the coffee mill....................................................... 13
Tips for a hotter coffee:........................................................... 13
Preparing espresso coffee using coffee beans......................... 13
Making long coffee using coffee beans................................... 13
Making espresso or long coffee using pre-ground coffee........ 14
7
INTRODUCTION
enabling the appliance to be unplugged when necessary.
Unplug directly from the plug only. Never pull the power
cable as you could damage it.
To disconnect the appliance completely, place the main
switch at the back of the appliance in the 0 position.
If the appliance is faulty, do not attempt to repair. Turn it
off, unplug from the mains socket and contact Customer
Services. Please see enclosed guarantee leaflet.
If the plug or power cable is damaged, it must be replaced
by De’Longhi Customer Services only to avoid all risk.
Please see enclosed guarantee leaflet.
Thank you for choosing this coffee machine ESAM6750. To get
the very best out of your new coffee machine it is advisable to
read these instructions before using the appliance. This is the
only way to ensure optimum results and ma­ximum safety.
The manufacturer is not liable for damage deriving from the
failure to comply with the user instructions.
•
Symbols used in these instructions
Important warnings are identified by these symbols. These
warnings must absolutely be respected.
•
Danger!
Failure to observe the warning could result in possible life
threatening injury from electric shock.
Important!
Keep all packaging (plastic bags, polystyrene foam) away from
children.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Important!
The appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Children must be
supervised to ensure they do not play with the appliance.
•
•
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Please note:
This symbol identifies important advice or information for the
user.
Danger of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
When the appliance is in operation, please be aware that the
cup warmer shelf (A7) becomes hot.
Letters in brackets
The letters in brackets refer to the legend in the Description of
the Appliance on page 3.
Troubleshooting and repairs
In the event of problems, first try and resolve them following
the information given in the section “Displayed messages” on
page 20 and “Troubleshooting” on page 21
If this does not resolve the problem or you require further
information, you should consult Customer Services. Please see
enclosed guarantee leaflet.
If repairs are required, contact De’Longhi Customer Services
only.
The addresses are given in the guarantee certificate provided
with the appliance.
DESIGNATED USE
This appliance is designed and made to prepare coffee and heat
drinks.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from
improper use of the appliance.
This is a household appliance only.
It is not suitable for use in:
• staff kitchen areas in shops, offices and other working
environments;
• farm houses;
• by clients in hotels, motels and other residential type
environments;
• bed and breakfast type environments.
SAFETY
Fundamental safety warnings
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore respect the following safety warnings:
• Never touch the appliance with damp hands.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
INSTRUCTIONS
Read these instructions carefully before using the appliance.
- Failure to follow these instructions may result in burns or
damage to the appliance.
8
Description of control panel (touch screen)
(page 3 - D )
Only the icons relating to the controls enabled for the particular
function currently being used will be lit on the control panel.
D1. Display: guides the user in using the appliance.
D2.
icon: to scroll forwards through the programming
menu.
D3.
icon: to deliver one cup of espresso coffee.
D4.
icon: to deliver two cups of espresso coffee.
D5. OK icon: to enable and confirm the selected function.
D6.
icon: to deliver hot water or steam.
D7. MILK icon: to deliver a cup of milk.
D8. LATTE MACCHIATO icon: to deliver a cup of
macchiato.
D9.
LONG icon: to deliver a cup of LONG coffee.
D10. CAPPUCCINO icon: to deliver a cappuccino.
D11. CAFFELATTE icon: to deliver a caffelatte.
D12. P icon: to access the Programming menu.
D13.ESC icon: to exit the selected function.
D14.
icon: to select the coffee taste.
D15.
icon: to select the coffee quantity.
D16.
icon: to scroll backwards through the programming
menu.
The manufacturer is not liable for damage deriving from
failure to respect these instructions.
Please note:
Keep these instructions. If the appliance is passed to other
persons, they must also be provided with these instructions.
DESCRIPTION
Description of the appliance
(page 3 - A )
A1. Grinding adjustment knob
A2. Beans container
A3. Main switch
A4. Beans container lid
A5. Cover for funnel and measure compartment
A6. Measure compartment
A7. Cup shelf (cup warmer active when Energy Saving is
disabled)
A8. Pre-ground coffee funnel
A9. Display
A10. Touch screen (control panel)
A11. Hot water and steam nozzle
A12. Infuser
A13. Water tank
A14. Power cable
A15. Cup tray
A16. Drip tray
A17. Compartment for macchiato/caffelatte glass
A18. Grounds tray
A19. Service door
A20. Coffee spout (adjustable height)
A21. Coffee guide
A22. ON/STAND-BY button
Please note :
A light touch is enough to activate the icon.
PRELIMINARY CHECKS
Checking the appliance
After removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged. Contact
Customer Services (see enclosed guarantee leaflet).
Description of milk container
(page 3 - B )
B1. Froth regulator
B2. Milk container handle
B3. CLEAN button
B4. Milk intake tube
B5. Frothed milk spout
B6. Lid with milk frother
Installing the appliance
Important!
When you install the appliance, you should follow the following
safety warnings:
• The appliance gives off heat. After positioning the
appliance on the worktop, leave a space of at least 3 cm
between the surfaces of the appliance and the side and
rear walls and at least 15 cm above the coffee maker.
• Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).
Description of the accessories
(page 3 - C )
C1. Hot water spout
C2. Measure
C3. Cleaning brush
C4. Indicator paper (total hardness test)
C5. Descaler
C6. Water softener filter (certain models only)
9
Connecting the appliance
TURNING THE APPLIANCE ON
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Please note:
Before turning the appliance on, make sure the main switch on
the back of the appliance is in the I position (fig. 1).
After setting up the appliance, each time the appliance is turned on, it performs an automatic preheat and rinse cycle which
cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
Danger of burns!
During rinsing, a little hot water is delivered from the coffee
spouts and collected in the drip tray underneath.
Avoid contact with splashes of water.
• To turn the appliance on, press the
button (fig. 5).
The message “Heating up, Please wait...” is displayed.
After heating, the message “Rinsing...” is displayed. As well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance is at temperature when the message “STANDARD
COFFEE”“Standard taste” is displayed.
Using the coffee maker for the first time
•
•
Please note :
Coffee has been used to factory test the appliance and it
is therefore completely normal for there to be traces of
coffee in the mill.
The machine is, however, guaranteed to be new.
You should customise water hardness as soon as possible
following the instructions in the section “Setting water
hardness” on page 19.
TURNING THE APPLIANCE OFF
1. Plug the appliance into the mains socket and place the
main switch on the back of the appliance in the I position
(fig. 1).
You must first choose the language (the languages scroll
through at intervals of about 3 seconds).
2. When English appears, press the OK icon for a few seconds
(fig. 2). Once the language has been saved, the message
“English set” is displayed.
Follow the instructions indicated by the appliance:
3. “FILL TANK!”: remove the water tank, fill to the MAX line
with fresh water then replace in the appliance (fig. 3).
4. “Insert water spout and press OK”: Check that the hot
water spout is inserted on the nozzle and place a container
with a minimum capacity of 100 ml underneath (fig. 4).
“Hot water, press OK “ Press the OK icon (fig. 2).
“Please wait.” is displayed and the appliance begins to
deliver water from the hot water spout. This is priming
the water system. (It is normal for the machine to make
some noise).
The appliance ends the first start up procedure, then the
message “Turning off, Please wait” is displayed and the
appliance goes off.
The coffee maker is now ready for normal use.
•
Please note:
When using the appliance for the first time, you need to
make 4/5 cups of coffee or 4/5 cappuccinos before the
appliance starts to give satisfactory results.
Each time the appliance is turned off, it performs an automatic
rinse cycle which cannot be interrupted.
Important!
To avoid damaging the appliance, always press the
button (fig. 5) to turn off.
Danger of burns!
During rinsing, a little hot water is delivered from the coffee
spouts.
Avoid contact with splashes of water.
•
To turn the appliance off, press the
button (fig. 5).
The appliance performs the rinse cycle then goes off.
Please note:
If the appliance is not used for an extended period, place the
main switch in the 0 position (fig. 6).
Never place the main switch in the 0 position while the
appliance is on.
MENU SETTINGS
When you access the programming menu by pressing the P button,
the following menu items are available: Rinse, Descale, Set language,
Energy Saving, Adjust time, Auto-start, Auto-off, Coffee temperature,
Water hardness, Water filter, Beep, Statistics, Default values.
10
Rinsing
To perform a rinse cycle to warm the internal circuits and make
the coffee delivered hotter, proceed as follows:
1. Press the P button to enter the menu;
2. Press the or
icon until “Rinsing” is displayed;
3. Press the OK icon: the message “Confirm?” is now
displayed.
4. Press the OK icon: hot water is delivered from the spout,
heating the internal circuits and making the coffee
delivered hotter.
3. Press the OK icon: the hours flash on the display;
4. Press the or
icon to change the hours;
5. Press the OK icon to confirm. The minutes flash on the
display;
6. Press the or
icon to change the minutes;
7. Press the OK icon to confirm;
8. Press the ESC icon to exit the programming menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Descaling
For instructions on descaling, see page 18.
Please note!
To enable this function, the time must be set correctly.
Setting the language
To modify the language on the display, proceed as follows:
1. Press the P icon to enter the programming menu;
2. Press the
or
: icon until “Set language” is
displayed;
3. Press the OK icon;
4. Press the or
icon until the required language is
displayed;
5. Press the OK icon to confirm;
6. Press the ESC icon to exit the menu.
1. Press the P icon to enter the programming menu;
2. Press the
or
icon until “Auto-start Disabled” is
displayed;
3. Press the OK icon. “Enable?” is displayed;
4. Press the or
icon to choose the hours;
5. Press the OK icon to confirm. The minutes flash on the
display;
6. Press the or
icon to change the minutes;
7. Press the OK icon to confirm. “Auto-start Enabled” is
displayed.
8. Press the ESC icon to exit the menu. The
symbol
appears next to the clock to indicate that auto-start has
been programmed.
To disable the function:
1. Press the P icon to enter the programming menu;
2. Press the or
icon until “Auto-start Enabled” is
displayed;
3. Press the OK icon. “Disable?” is displayed;
4. Press the OK icon to confirm;
5. Press the ESC icon to exit the menu. The
symbol is no
longer displayed.
Energy Saving
Use this function to enable or disable energy saving mode.
When enabled, the function reduces energy consumption in
compliance with European regulations.
1. Press the P icon to enter the programming menu;
2. Press the
or
icon until “Energy saving” is
displayed;
3. Press the OK icon. “Disable?” is displayed, or “Enable?” if
the function has already been disabled.
4. Press the OK icon to disable or enable the function or ESC
to exit the menu.
When the function is enabled, if the appliance is not used for
about 1 minute, “Energy Saving” is displayed.
•
•
Auto-off (Stand by)
Auto-off can be changed so that the appliance goes off after 15
or 30 minutes, or after 1, 2 or 3 hours.
1. Press the P icon to enter the programming menu;
2. Press the or
icon until “Auto-off” is displayed;
3. Press the OK icon;
4. Press the or
icon until the required time appears
(15 or 30 minutes, or 1, 2 or 3 hours);
5. Press the OK icon to confirm;
6. Press the ESC icon to exit the menu.
Auto-off is programmed.
Please note!
A few seconds may elapse between “Energy Saving” mode
and delivery of the first drink. This is indicated by the rapid
increase then decrease of the progress bar and display of
the message “Preparation underway”.
When “Energy Saving” is disabled, the appliance turns the
cup warmer on automatically.
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the P icon to enter the programming menu;
2. Press the or
icon until “Adjust time” is displayed;
11
Coffee temperature
To modify the temperature of the water used to make the
coffee, proceed as follows:
1. Press the P icon to enter the programming menu;
2. Press the
or
icon until “Coffee temperature” is
displayed;
3. Press the OK icon;
4. Press the or
icon until the required temperature
(l = low; llll = high) is displayed;
5. Press the OK icon to confirm;
6. Press the ESC icon to exit the menu.
displayed;
3. Press the OK icon;
4. The message “Confirm?” is now displayed.
5. Press the OK icon to confirm and exit.
MAKING COFFEE
Selecting the coffee taste
The appliance is set by default to make coffee with a standard
taste.
You can choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
Setting water hardness
For instructions on the water filter, see page 19.
Install filter
For instructions on the water filter, see page 19.
To change the taste, press the
until the required taste is displayed.
Beep
This enables or disables the beep emitted by the machine each
time an icon is pressed or an accessory is inserted/removed. The
beep is active by default.
1. Press the P button to enter the menu;
2. Press the
or
icon until “Beep enabled” is
displayed;
3. Press the OK icon. “Disable?” is displayed;
4. Press the OK icon to disable the beep. “Beep Disabled” is
displayed;
5. Press the ESC icon to exit the programming menu.
icon (fig. 7) repeatedly
Selecting the quantity of coffee in the cup
The appliance is set by default to make a standard quantity of
coffee.
To select the quantity of coffee, press the
icon (fig.
8) repeatedly until the message corresponding to the required
quantity of coffee is displayed:
Corresponding
coffee
Statistics function
This displays statistics relating to the machine.
To display, proceed as follows:
1. Press the P icon to enter the programming menu;
2. Press the or
icon until “Statistics” is displayed;
3. Press the OK icon;
4. By pressing the or
icon, you can check:
- how many coffees have been made;
- the total of drinks with milk made (CAPPUCCINO,
MACCHIATO, CAFFELATTE, MILK);
- how many times the machine has been descaled;
- the total number of litres of water delivered;
- how many filters have been used.
5. Press the ESC icon twice to exit the menu.
espresso
(ml)
LONG COFFEE
(ml)
MY COFFEE
program. from
20 to 180
program. from
20 to 250
SHORT
≃40
≃ 125
STANDARD
≃60
≃ 175
LONG
≃90
≃ 210
EXTRA LONG
≃120
≃ 250
Customising the espresso “my coffee” quantity
The appliance is set by default to automatically deliver 30 ml
of “my coffee”. To modify these settings, proceed as follows:The
appliance is set by default to automatically deliver 30 ml of “my
coffee”. To modify these settings, proceed as follows:
1. Place a cup under the coffee spouts ( fig. 13).
2. Press the
icon repeatedly (fig. 8) until “MY
COFFEE” is displayed.
3. Press and hold the
icon until “Program Quantity”
is displayed, then release. The appliance starts delivering
coffee and the
icon flashes;
4. As soon as the coffee in the cup reaches the required level,
press the
icon again.
The quantity set has now been programmed.
Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language
which remains as set).
1. Press the P icon to enter the menu;
2. Press the
or
icon until “Default Values” is
12
Programming the long “my coffee” quantity
The appliance is set by default to automatically deliver about
100ml of LONG coffee.
To modify this quantity, proceed as follows:
1. Place a cup under the coffee spouts ( fig. 18).
2. Press the
icon repeatedly (fig. 8) until “MY
COFFEE” is displayed.
3. Press the LONG icon (fig. 10) until “Program Quantity” is
displayed, then release. The appliance starts delivering
coffee and the LONG icon flashes;
4. As soon as the coffee in the cup reaches the required level,
press the LONG icon again.
The quantity set has now been programmed.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
Preparing espresso coffee using coffee beans
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
1.
2. 3.
Fill the container with coffee beans (fig. 12).
Place under the coffee spouts:
- 1 cup, if you want 1 coffee (fig. 13);
- 2 cups, if you want 2 coffees (fig. 14);
Lower the spouts as near as possible to the cup. This makes
a creamier coffee (fig. 15).
4. Press the icon corresponding to the number of coffees
required (1 cup
or 2 cups
) (fig. 9 and
16).
5. Preparation begins. The amount of coffee and taste
selected are displayed together with a progress bar which
gradually fills as preparation progresses (fig. 17).
Once the coffee has been made, the appliance prepares for use
again.
Regulating the coffee mill
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that
delivery is either too fast or too slow (a drop at a time), this
can be corrected by adjusting the grinding adjustment knob
(fig. 11).
Please note!
The grinding adjustment knob must only be turned when the
coffee mill is in operation.
For fuller bodied creamier coffee,
turn one click anticlockwise
towards “1” (finer ground coffee).
For faster delivery (not a drop at
a time), turn one click clockwise
towards “7” (coarser ground
coffee).
Please note:
While the machine is making coffee, delivery can be
interrupted at any moment by pressing one of the coffee
icons (
or
).
• At the end of delivery, to increase the quantity of coffee in
the cup, just press (within 3 seconds) one of the coffee icons
(
or
).
Once the coffee has been made, the appliance is ready to use
again.
•
These adjustments will only be evident after at least 2 cups of
coffee have been delivered.
If delivery is still too fast or too slow, repeat the correction,
turning the knob another click.
Important!
If the coffee is delivered a drop at a time, too fast and not creamy
enough or too cold, read the tips in the “Troubleshooting”
section on page 21.
Various alarm messages could be displayed while the machine
is in use. Their meaning is explained in the section “Displayed
messages” (page 20).
Tips for a hotter coffee:
For a hotter coffee, you are recommended to:
• perform a rinse cycle by selecting the “Rinsing” function
in the settings menu: Hot water is delivered from the
spout, heating the internal circuits and making the coffee
delivered hotter;
• enable the cup warmer and leave the cups to warm;
• warm the cups by rinsing them with hot water (using the
hot water function);
• set the “high” coffee temperature in the menu
(llll).
Making long coffee using coffee beans
Please note!
When this function is enabled, a long coffee similar to drip
coffee is obtained.
Important!
13
MAKING DRINKS WITH MILK
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
Please note!
A few seconds may elapse between energy saving mode and
delivery of the first drink.
1. Fill the container with coffee beans (fig. 12);
2. Adjust the height of the spout according to the cup used.
Put the cup for long coffee under the spouts (fig. 18);
3. Press the LONG icon (fig. 10). Preparation begins. A
progress bar appears on the display and gradually
advances as the procedure progresses.
Once the coffee has been made, the appliance prepares for use
again.
•
•
•
Filling and attaching the milk container
1. Turn the lid of the milk container clockwise until it
becomes noticeably difficult to turn, then remove the lid
(fig. 20).
2. Fill the milk container with a sufficient quantity of milk,
not exceeding the MAX level marked on the handle (fig.
21).
Please note:
While the machine is making coffee, delivery can be
interrupted at any moment by pressing the LONG icon.
Only one cup of long coffee can be made at a time.
When delivering more than 125 ml, the appliance
automatically grinds more coffee halfway through
delivery.
Please note!
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C). To avoid milk
with poor froth or large bubbles, always clean the milk lid and
hot water nozzle as described in the section “Cleaning the milk
container” on pages 15 and 18.
Making espresso or long coffee using pre-ground coffee
•
•
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (fig. 22).
4. Replace the milk container lid and turn anticlockwise as
far as it will go.
5. Remove the hot water spout from the nozzle (fig. 23).
6. Attach the container to the nozzle and push as far as it
will go (fig. 24). The machine emits a beep (if the beep
function is enabled).
7. Place a sufficiently large cup under the coffee spouts and
frothed milk spout.
To use particularly tall cups/glasses, raise the lid of the
special compartment in the cup tray (fig. 25).
8. Follow the instructions below for each function.
Important!
Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
it. This could damage the appliance.
Never use more than one level
measure or it could dirty the inside
of the machine or block the funnel.
Please note!
If you use pre-ground coffee, you can only make one cup of
coffee at a time.
Making caffelatte
1. After attaching the milk container, position the froth regulator on CAFFELATTE (fig. 26) printed on the milk container lid.
2. Press the CAFFELATTE icon (fig. 27). “Caffelatte... Froth
regulator in position 3” is displayed. After a few seconds,
frothed milk is delivered from the milk spout into the
cup below. Milk delivery stops automatically and coffee
delivery begins.
1. Press the
icon repeatedly (fig. 7) until “Preground” flashes on the display.
2. Put one level measure of pre-ground coffee into the
funnel (fig. 19).
3. Place a cup under the coffee spouts.
4. To make espresso coffee, press the 1 cup
icon
(fig. 9). To make long coffee, press the LONG icon (fig.
10).
5. Preparation begins. The amount of coffee and taste
selected are displayed together with a progress bar which
gradually fills as preparation progresses.
Once the coffee has been made, the appliance prepares for use
again.
Please note!
If during delivery you want to stop preparing milk, press the
CAFFELATTE icon or interrupt preparation of the coffee by
pressing the
icon.
14
Making cappuccino
1. After attaching the milk container, position the froth
regulator on CAPPUCCINO (fig. 28) printed on the milk
container lid. The quality of froth can be adjusted
during delivery by moving the regulator slightly
towards LATTE MACCHIATO for a denser froth.
Moving it towards the word CAPPUCCINO obtains a
less dense froth.
2. Press the CAPPUCCINO icon (fig. 29). “Cappuccino...
Froth regulator in position 1” is displayed. After a few
seconds, frothed milk flows out of the milk spout into the
cup below. Milk delivery stops automatically and coffee
delivery begins.
Cleaning the milk container after use
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water leaks out of the frothed milk tube (B5).
Avoid contact with splashes of water.
When “Press CLEAN button” flashes on the display (each time
you use a milk function):
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Press the CLEAN button (fig. 33) and keep pressing until
the progress bar which appears on the display together
with the message “Cleaning...” is complete.
4. Remove the milk container and always clean the nozzle
with a sponge (fig. 34).
Please note!
If during delivery you want to stop preparing milk, press the
CAPPUCCINO icon or interrupt preparation of the coffee by
pressing the
icon.
Making macchiato
1. After attaching the milk container, position the froth regulator (B1) on LATTE MACCHIATO (fig. 30) printed on the
milk container lid.
2. Press the LATTE MACCHIATO icon (fig. 31). “Latte Macchiato... Froth regulator in position 2” is displayed.
After a few seconds, frothed milk flows out of the milk
spout into the cup below.
Milk delivery stops automatically and coffee delivery
begins.
•
•
•
Nota Bene!
When “Press CLEAN button” flashes on the display, you
can still prepare any type of coffee or milk. If you have to
make a number of drinks with milk, wait until you have
delivered the last cup before cleaning the container.
The milk left in the container can be kept in the
refrigerator.
In some cases, to clean you must wait for the appliance to
heat up, holding the CLEAN button down.
Programming the quantities of coffee and milk in the
cup
The appliance is set by default to automatically deliver standard
quantities.
To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk spout.
2. Press the icon corresponding to the function you want to
programme (CAFFELATTE, CAPPUCCINO, LATTE MACCHIATO
or MILK) until “Milk for... Program quantity” appears on
the display and the icon corresponding to the selected
function flashes.
3. Release the icon. The appliance starts delivering milk.
4. When the required quantity of milk has been delivered
into the cup, press the icon again.
5. After a few seconds, the appliance starts delivering coffee
into the cup and the message “Coffee for... Program
quantity” is displayed (with the exception of the MILK
function) and the
icon flashes.
6. As soon as the coffee in the cup reaches the required level,
press the
icon. Coffee delivery stops.
The machine is now reprogrammed with the new quantities.
Please note!
If during delivery you want to stop preparing milk, press the
LATTE MACCHIATO icon or interrupt preparation of the coffee by
pressing the
icon.
Making milk
1. After attaching the milk container, position the froth
regulator according to the quantity of froth you require
(pos. 3 caffelatte = little froth; pos. 1 cappuccino =
abundant froth).
2. Press the MILK icon (fig. 32). “MILK” appears on the
display
After a few seconds, frothed milk is delivered from the
milk spout into the cup below.
Delivery of milk stops automatically.
Please note!
If during delivery you want to stop preparing milk, press the
MILK icon once.
15
PREPARING HOT WATER OR STEAM
Important!
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Important! Danger of burns.
Do not leave the appliance unattended while delivering hot
water or steam.
The spout becomes hot during delivery. Hold by the handle
only.
Tips for using steam to froth milk
• When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially skimmed milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow movements in an upward direction.
• To avoid milk with poor froth or large bubbles, always clean the spout as described in the following section.
Please note!
If “Energy Saving” is active, you may have to wait a few seconds
before hot water and steam are delivered.
Delivering hot water
1. Make sure the hot water spout is attached correctly (fig.
6).
2. Place a container under the spout (as close as possible to
avoid splashes).
3. Press the
button (fig. 35). “HOT WATER” AND “STEAM” is displayed with a flashing arrow near the selection:
press Ok to select: “Hot water” is displayed, together with
a progress bar which fills gradually as preparation proceeds.
4. The machine delivers 250 ml of hot water, then delivery
stops automatically.
To interrupt delivery of hot water manually, press the
button again.
Cleaning the spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
1. Place a container under the cappuccino maker and press
the
button to deliver a little water. Stop the flow of
hot water by pressing the
button again.
2. Wait a few minutes for the cappuccino maker to cool
down, then extract the hot water spout. Hold the spout
with one hand and with the other, turn the cappuccino
maker anticlockwise (fig. 36) and pull downwards to remove it.
3. Also remove the steam nozzle by pulling it downwards
(fig. 37).
4. Check the hole shown by the arrow in fig. 37 is not blocked. If necessary, clean with a pin.
5. Wash all parts of the cappuccino maker thoroughly with a
sponge and warm water.
6. Reinsert the nozzle and replace the cappuccino maker on
the nozzle, turning it and pushing it upwards until it is
attached.
Changing the quantity of water delivered automatically.
The machine is set by default to automatically delivery 250 ml
of hot water.
To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press and hold the
button until “Hot Water Program Quantity” is displayed, then release.
3. When the hot water in the cup reaches the required level,
press the
button again.
The machine is now reprogrammed with the new quantity.
CLEANING
Steam delivery
1. Make sure the hot water spout is attached correctly (fig. 4).
2. Fill a container with the liquid to be heated/frothed and
immerse the spout/cappuccino maker in the liquid.
3. Press the
button (fig. 35). “HOT WATER” AND “STEAM” is displayed with a flashing arrow near the selection:
to move the arrow near “STEAM”, press the
button
again. Press the OK button. After a few seconds, the steam
to heat the liquid comes out of the cappuccino maker;
4. When the required temperature is obtained, interrupt
steam delivery by pressing the
button again. (You
should not discharge steam for more than 3 minutes at a
time).
Cleaning the coffee maker
The following parts of the machine must be cleaned regularly:
- coffee grounds container (A18),
- drip tray (A16),
- inside the machine, accessible after opening the service
door (A19),
- water tank (A13),
- coffee spouts (A20) and hot water nozzle (A11),
- pre-ground coffee funnel (A8),
- infuser (A12),
- milk container (B)
- control panel (D)
16
•
•
•
4. Replace the drip tray complete with grounds container;
5. Close the service door.
Important!
Do not use solvents, abrasive detergents or alcohol to
clean the coffee maker. With De’Longhi superautomatic
coffee makers, you need not use chemical products to
clean the machine.
None of the components of the appliance can be washed
in a dishwasher with the exception of the milk container
(B).
Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
Cleaning the inside of the machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned
off (see “Turning off”) and unplugged from the mains power
supply.
Never immerse the coffee maker in water.
1. Check regularly (about every 100 coffees) that the inside
of the appliance (accessible after removing the drip tray)
is not dirty.If necessary, remove coffee deposits with the
brush or a sponge.
2. Remove the residues with a vacuum cleaner (fig. 43).
Cleaning the coffee grounds container
When “EMPTY GROUNDS CONTAINER” is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coffee cannot be made.
Even if not full, the empty grounds container message is
displayed 72 hours after the last coffee has been prepared. For
the 72 hours to be calculated correctly, the machine must never
be turned off with the main switch in the 0 position.
To clean (with the machine on):
• Open the service door on the front of the appliance (fig.
38), extract the drip tray (fig. 39), empty and clean.
• Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
with the spatula on the brush provided.
Cleaning the water tank
1. Clean the water tank (A13) regularly (about once a month)
with a damp cloth and a little mild washing up liquid.
2. After cleaning the water tank rinse it thoroughly to
remove all washing up liquid residues.
Cleaning the coffee spouts
1. Clean the coffee spouts with a sponge or cloth (fig. 41).
2. Check the holes in the coffee spout are not blocked. If
necessary, remove coffee deposits with a toothpick (fig.
42).
Cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the pre-ground
coffee funnel is not blocked.
If necessary, remove coffee deposits with the brush.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds. If this is not done,
when you make the next coffees, the grounds container may
fill up more than expected and clog the machine.
Cleaning the infuser
The infuser (A12) must be cleaned at least once a month.
Cleaning the drip tray
Important!
The infuser must not be extracted when the machine is on.
Important!
If the drip tray is not emptied regularly, the water could overflow from the edge and seep inside or around the machine.
This could damage the machine, the surface it rests on or the
surrounding area.
1. Make sure the machine is correctly turned off (see Turning
off).
2. Open the service door (fig. 38).
3. Remove the drip tray and grounds container (fig. 39);
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (fig. 44).
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 38).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned.
To remove the drip tray:
1. Open the service door (fig. 38);
2. Remove the drip tray and the grounds container (fig. 39);
3. Empty the drip tray and grounds container (A18) and
wash them;
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID - NO DISH WASHER
Do not use washing up liquid to clean the infuser as it could
cause damage.
17
top basket of the dishwasher.
Make sure there are no milk residues left inside the holes
and the groove on the fine end of the froth regulator.
5. Check that the intake tube and spout are not clogged with
milk residues.
6. Replace the froth regulator, milk spout and intake tube.
7. Replace the lid on the milk container, turning it
anticlockwise to hook it in place.
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
6. After cleaning, replace the infuser by sliding it onto the
internal support and pin at the bottom, then push the
PUSH symbol fully in until it clicks into place.
DESCALING
Descale the machine when the message “DESCALE!” flashes on
the display.
Important!
Descaler contains acids which may irritate the skin and eyes.
It is vital to respect the manufacturer’s safety warnings given on
the descaler pack and the warnings relating to the procedure to
follow in the event of contact with the skin and eyes.
Please note!
If you encounter difficulty
inserting the infuser, before
inserting it you must adapt it to
the right dimension by pressing it
forcefully from the bottom and
Please note!
Under no circumstances should you use sulphamic or acetic
based descalers. Their use invalidates the guarantee.
Failure to descale the appliance as described also invalidates
the guarantee.
top as shown in the figure.
7. Once inserted, make sure the two red
buttons have snapped out.
8. Replace the drip tray and grounds
container.
9. Close the service door.
1.
2. 3. Turn the machine on.
Enter the programming menu by pressing the P icon.
Select by pressing the OK icon.
“Descaling Confirm?” is displayed. Press OK to enable the
function.
4. The message “Add descaler”“Press OK” is displayed.
5. Before confirming, empty the water tank (A13).
Pour the descaler diluted with water (respecting the
proportions indicated on the descaler pack) into the water
tank.
Place an empty container with a minimum capacity of 1.5
litres under the hot water spout.
Cleaning the milk container
Clean the milk container each time you prepare milk as
described below:
1. Turn the lid of the milk
container clockwise
then remove it.
2. Remove the milk
spout and intake
tube.
3. Remove the froth
regulator by pulling it
outwards.
4. Wash
all
the
components
thoroughly
with
hot water and mild
washing-up liquid.
All
components
can be washed
in a dishwasher,
placing them in the
Important! Danger of burns
Hot water containing acid flows out of the hot water spout.
Avoid contact with splashes of water.
6. Confirm by pressing the OK icon.
7. The message “Descaling...” is displayed.
The descaling programme starts and the descaler liquid
comes out of the water spout. The descale programme
automatically performs a series of rinses and pauses to
remove limescale deposits from inside the machine.
After about 30 minutes, the message “Rinsing FILL TANK!” is
displayed.
8. The appliance is now ready for rinsing through with clean
water.
18
Remove the water tank, empty, rinse under running
water, fill with clean water and replace. “Rinsing... Press
OK” is displayed.
9. Empty the container used to collect the descaler solution
and replace it under the hot water spout.
10. Press the OK icon to start rinsing. Hot water flows out of
the spout and the message “Rinsing...” is displayed.
11. When the water tank is completely empty, the message
“Rinsing Complete... Press OK” is displayed.
12. Press the OK icon. The appliance goes off.
To use it again, turn the appliance on by pressing the
button.
The machine is now reprogrammed with the new water
hardness setting.
WATER SOFTENER FILTER (if fitted)
Certain models are fitted with a water softener filter. If this
is not the case with your model, you are recommended to
purchase one from De’Longhi Customer Services. To use the
filter correctly, follow the instructions below.
Installing the filter
1. Remove the filter from the packaging.
2. Turn the date indicator disk until the next two months of
use are displayed. (fig. 45).
SETTING WATER HARDNESS
Nota Bene
T��������������������������������������������������������������
he filter lasts about two months if the appliance is used normally. If the coffee machine is left unused with the filter installed, it will last a maximum of three weeks.
3. Extract the tank from the appliance and fill with water.
4. �������������������������������������������������������
Insert the filter in the water tank and immerse it completely for about 30 seconds, turning it upside down to
enable the air bubbles to escape (fig. 46).
5. Insert the filter in the filter housing and press as far as it
will go (fig. 46).
6. Close the tank with the lid, then put the tank back in the
machine (fig. 47).
When you install the filter, you must notify the appliance of its
presence.
7. Access the menu by pressing the P icon;
8. Scroll through the menu by pressing the or
icon
until “Install water filter” is displayed.
9. Press the OK icon.
10. The message “Water filter, Install?” is displayed.
11. Press the OK icon to confirm the selection. The message
“Insert water spout and press OK”.
12. ��������������������������������������������������������
Position a container under the hot water spout (min. capacity: 100 ml).
13. Press OK to confirm the selection. The appliance begins
delivering hot water and “Please wait” is displayed.
14. After delivery, the appliance is automatically ready to make
the next drink.
After delivery, the appliance is automatically ready to make the
next drink.
The DESCALE message is displayed after a period of time established according to water hardness.
The machine is set by default for a hardness value of 4 (very
hard water).
The machine can also be programmed according to the actual
hardness of the mains water in the various regions, varying the
frequency with which the message is displayed.
Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper from
its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
soft water l
slightly hard water
ll
hard water lll
very hard water
llll
Set water hardness
1. Press the P icon to enter the programming menu.
2. Press the or
icon and select “Water hardness”.
3. Confirm the selection by pressing the OK icon.
4. Press the or
icon to set the number of squares
formed on the reactive strip (see figure in the previous
section).
5. Press the OK icon to confirm the setting.
6. Press the ESC icon to exit the menu.
Replacing the filter
When “REPLACE FILTER” is displayed, after two months (see
date indicator) or if the appliance has not been used for 3
weeks, you should replace the filter:
1. Extract the tank and exhausted filter;
2. Remove the new filter from the packaging and proceed as
illustrated on the previous pragraph (points 3-4-5-6).
19
3. Position a container with a minimum capacity of 100 ml
under the hot water spout.
4. Access the menu by pressing the P icon;
5. Scroll through the menu by pressing the or
icon
until “Replace filter?” is displayed.
6. Press the OK icon.
7. “CONFIRM?” is displayed.
8. Press the OK icon to confirm.
9. “Insert water spout and press OK” is displayed;
10. Press OK to confirm the selection. The appliance begins
delivering hot water and “Please wait” is displayed.
11. After delivery, the appliance is automatically ready to make
the next drink.
The new filter is now active and you can use the coffee machine.
Size: LxHxD: Cable length: Weight:
Beans container capacity: The appliance complies with the following EC directives:
•
•
EC Regulation 1275/2008 for standby;
Low Voltage Directive 2006/95/EC and subsequent
amendments;
• EMC Directive 2004/108/EC and subsequent
amendments
• Materials and accessories coming into contact with food
conform to EEC regulation 1935/2004.
DISPOSAL
TECHNICAL SPECIFICATION
Voltage: In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with household waste, but taken to an authorised waste separation and recycling centre.
220-240 V~ 50/60 Hz max. 10A
Absorbed power:
Pressure:
Water tank capacity:
282x374x441 mm
1,5 m
11,4 Kg
250 g
1350W
15 bar
1,7 l
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
REMEDY
FILL TANK !
•
Insufficient water in the tank.
•
Fill the tank with water and/or insert it correctly,
pushing it as far as it will go until it clicks into place
(fig. 3).
GROUND TOO FINE ADJUST
MILL!
Insert water spout and press
OK
•
The grinding is too fine and the coffee is delivered
too slowly.
•
- Repeat coffee delivery and turn the grinding
adjustment knob one click clockwise towards “7”
while the coffee mill is in operation. If after making
at least 2 coffees delivery is still too slow, repeat
the correction procedure, turning the grinding
adjustment knob another click until delivery is
correct.
INSERT WATER SPOUT!
•
The water spout is not inserted or is inserted
incorrectly.
•
Insert water spout as far as it will go.
EMPTY GROUNDS
CONTAINER!
•
The grounds container is too full or more than 3
days have passed since you last made coffee (this
guarantees correct hygiene of the machine).
•
Empty the grounds container and clean, then
replace. Important: when removing the drip tray,
the grounds container must be emptied, even if it
contains few grounds. If this is not done, when you
make the next coffees, the grounds container may fill
up more than expected and clog the machine.
INSERT GROUNDS CONTAINER
•
After cleaning, the grounds container has not been
replaced.
•
Open the service door, remove the drip tray and
insert the grounds container.
ADD PRE-GROUND COFFEE
•
The “pre-ground coffee” function has been selected
without placing any pre-ground coffee in the funnel.
•
Place pre-ground coffee in the funnel or deselect the
“pre-ground” function.
DESCALE!
•
The machine must be descaled.
•
The descaling procedure described in the “Descaling”
section needs to be performed as soon as possible.
LESS COFFEE!
•
Too much coffee has been used.
•
Select a milder taste or reduce the quantity of preground coffee.
20
DISPLAYED MESSAGE
POSSIBLE CAUSE
REMEDY
FILL BEANS CONTAINER!
•
The coffee beans have run out.
•
Fill the beans container
•
The pre-ground coffee funnel is clogged.
•
Empty the funnel with the help of a brush as
described in the section “Cleaning the pre-ground
coffee funnel”.
INSERT INFUSER ASSEMBLY!
•
The infuser has not been replaced after cleaning.
•
Insert the infuser as described in the paragraph
“Cleaning the infuser”.
INSERT MILK CONTAINER
•
The milk container is not inserted correctly.
•
Insert the milk container as far as it will go.
CLOSE DOOR!
•
The service door is open
•
Close the service door.
PRESS CLEAN BUTTON
•
Milk has been delivered recently and the tubes
inside the milk container must be cleaned.
•
Press the CLEAN button and keep it pressed until the
progress bar which appears on the display together
with the message “Cleaning...” is complete.
ADD PRE-GROUND COFFEE
Press OK
•
The “pre-ground coffee” function has been selected
without placing any pre-ground coffee in the funnel.
•
Place pre-ground coffee in the funnel.
•
The funnel (A8) is blocked.
•
Empty the funnel with the help of a knife, as
described in the section “Cleaning the pre-ground
coffee funnel”.
Energy Saving
•
The function is active and reduces electricity
consumption.
•
Disable the function in the menu.
GENERAL ALARM!
•
The inside of the appliance is very dirty.
•
Clean the inside of the appliance thoroughly, as
described in the section “Cleaning and maintenance”.
If the message is still displayed after cleaning,
contact a Customer Service.
TROUBLESHOOTING
Below is a list of some of the possible problems.
If the problem cannot be resolved as described, contact a Customer Service.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The coffee is not hot
•
•
The cups were not preheated.
•
The coffee is not creamy
enough.
The coffee is delivered too
slowly or a drop at a time.
Enable the cup warmer, leave the cups at least 20
minutes to warm up.
Warm the cups by rinsing them with hot water
(using the hot water function).
•
The infuser has cooled down because 2/3 minutes
have elapsed since the last coffee was made.
•
Before making the coffee, heat the infuser by
pressing the
icon (see the sections “Tips for a
hotter coffee”).
•
A low coffee temperature is set.
•
Set a high coffee temperature in the menu.
•
The coffee is ground too coarsely.
•
Turn the grinding adjustment knob one click
anticlockwise towards “1” while the coffee mill is
in operation (fig. 8). Continue one click at a time
until coffee delivery is satisfactory. The effect is only
visible after delivering 2 coffees.
•
Wrong type of coffee
•
Use a type of coffee for espresso coffee makers.
•
The coffee is ground too finely.
•
Turn the grinding adjustment knob one click
clockwise towards “7” while the coffee mill is in
operation (fig. 11). Continue one click at a time
until coffee delivery is satisfactory. The effect is only
visible after delivering 2 coffees.
21
PROBLEM
POSSIBLE CAUSE
SOLUTION
The coffee does not come out
of the spouts, but from around
the service door.
•
The holes in the spouts are clogged with dry coffee
deposits.
•
Clean the spouts with a toothpick, sponge or hard
bristled kitchen brush.
•
The coffee guide inside the service door is blocked
and cannot swing.
•
Thoroughly clean the coffee guide, particularly near
the hinges.
The coffee is delivered too
quickly.
•
The coffee is ground too coarsely.
•
Turn the grinding adjustment knob one click
anticlockwise towards “1” while the coffee mill is
in operation (fig. 11). Avoid turning the grinding
adjustment knob excessively otherwise when you
select two cups, the coffee may be delivered a drop
at a time.
Coffee does not come out of
one of the spouts.
•
The spouts are blocked.
•
Clean the spouts with a toothpick (fig. 40).
Water comes out of the spouts
instead of coffee.
•
The pre-ground coffee may be blocked in the funnel
(A8).
•
Empty the funnel with the help of a knife, as
described in the section “Cleaning the pre-ground
coffee funnel”.
The milk contains bubbles or
squirts out of the milk spout.
•
The milk is not cold enough or is not semi-skimmed.
•
You should ideally use skimmed or semi-skimmed
milk at refrigerator temperature (about 5°C). If the
result is not as you wished, try changing brand of
milk.
•
The froth regulator is incorrectly adjusted.
•
Adjust following the instructions in the section on
preparing drinks with milk.
•
The milk container lid is dirty.
•
Clean the milk container lid as described in the
section “Cleaning the milk container”.
•
The froth regulator is incorrectly adjusted.
•
Adjust following the instructions in the section on
preparing drinks with milk.
•
The milk container lid is dirty.
•
Place the ring in the CAPPUCCINO position.
The appliance does not come
on.
•
It is not plugged into the mains socket.
•
Plug into the mains socket.
•
The main switch is not turned on.
•
Place the main switch in the I position (fig. 29).
The LONG coffee has too much
froth
•
The coffee is ground too finely.
•
Turn the grinding adjustment knob one click
clockwise towards “7” while the coffee mill is in
operation (fig. 11). Continue one click at a time until
coffee delivery is satisfactory. The effect is only
visible after delivering 2 coffees.
The milk does not come out of
the milk spout.
•
The milk container lid is dirty.
•
Clean the milk container lid as described in the
section “Cleaning the milk container”.
“Energy Saving” mode is
enabled, but the cup warmer
is hot
•
A number of drinks have been prepared in rapid
succession.
The milk is not frothed.
22